Vivitek D8 PointRacer Series User manual

D8 Series
User Manual
ϡ͗͘Ί
⫼᠋᠟‫ݠ‬
Manual del usuario
Manuel de l'utilisateur
Benutzerhandbuch
㇠㟝㣄 ㉘⮹㉐
Ɋɭɤɨɜɨɞɫɬɜɨɩɨɥɶɡɨɜɚɬɟɥɹ
Gebruikershandleiding
,QVWUXNFMDREVáXJL
8åLYDWHOVNiSĜtUXþND
ǼȖȤİȚȡȓįȚȠȤȡȒıȘȢ
.XOODQÕP.ÕODYX]X
Manuale d'uso
Handbok
%UXJHUYHMOHGQLQJ
%UXNHUYHLOHGQLQJ
Käyttöohje
)HOKDV]QiOyLNp]LN|Q\Y
Ωϝϱϝ΍ϝϡαΕΥΩϡ
0DQXDOGR8VXiULR
Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be
reproduced without written consent of the author.
© Copyright 2011
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied
warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to
revise this publication and to make changes from time to time in the content hereof without obligation of
the manufacturer to notify any person of such revision or changes.
Trademark Recognition
Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations and pending applications in other countries throughout the world.
All other product names used in this manual are the properties of their respective owners and are acknowledged.
—i—
DLP Projector—User’s Manual
Important Safety Information
Important:
It is strongly recommended that you read this section carefully before using the projector. These
safety and usage instructions will ensure that you enjoy many years of safe use of the projector.
Keep this manual for future reference.
Symbols Used
Warning symbols are used on the unit and in this manual to alert you of hazardous situations.
The following styles are used in this manual to alert you to important information.
Note:
Provides additional information on the topic at hand.
Important:
Provides additional information that should not be overlooked.
Caution:
Alerts you to situations that may damage the unit.
Warning:
Alerts you to situations that may damage the unit, create a hazardous environment, or cause personal injury.
Throughout this manual, component parts and items in the OSD menus are denoted in bold font as in this
example:
“Push the Menu button on the remote control to open the Main menu.”
General Safety Information
¾
Do not open the unit case. Aside from the projection lamp, there are no user-serviceable parts in
the unit. For servicing, contact qualified service personnel.
¾
Follow all warnings and cautions in this manual and on the unit case.
¾
The projection lamp is extremely bright by design. To avoid damage to eyes, do not look into the
lens when the lamp is on.
¾
Do not place the unit on an unstable surface, cart, or stand.
¾
Avoid using the system near water, in direct sunlight, or near a heating device.
¾
Do not place heavy objects such as books or bags on the unit.
— ii —
Preface
Projector Installation Notice
¾
Place the projector in a horizontal position
The tilt angle of the projector should not exceed 15 degrees, nor should the projector be installed in
any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically.
¾
Allow at least 50 cm clearance around the exhaust vent.
¾
Ensure that the intake vents do not recycle hot air from the exhaust vent.
¾
When operating the projector in an enclosed space, ensure that the surrounding air temperature
within the enclosure does not exceed 5 – 35°C while the projector is running, and the air intake and
exhaust vents are unobstructed.
¾
All enclosures should pass a certified thermal evaluation to ensure that the projector does not
recycle exhaust air, as this may cause the device to shutdown even if the enclosure temperature is
with the acceptable 5 – 35°C range.
– iii –
DLP Projector—User’s Manual
Power Safety
¾
Only use the supplied power cord.
¾
Do not place anything on the power cord. Place the power cord where it will not be in the way of
foot traffic.
¾
Remove the batteries from the remote control when storing or not in use for a prolonged period.
Replacing the Lamp
Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 41
for clear and safe instructions for this procedure. Before replacing the lamp:
¾
Unplug the power cord.
¾
Allow the lamp to cool for about one hour.
Cleaning the Projector
¾
Unplug the power cord before cleaning. See Cleaning the Projector page 44.
¾
Allow the lamp to cool for about one hour.
Regulatory Warnings
Before installing and using the projector, read the regulatory notices in the Regulatory Compliance on
page 58.
Important Recycle Instructions:
Hg
Lamp(s) inside this product contain mercury. This product may contain other electronic waste that
can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal
Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG. For lamp
specific disposal information check WWW.LAMPRECYCLE.ORG.
Symbol Explanations
DISPOSAL: Do not use household or municipal waste collection services for
disposal of electrical and electronic equipment. EU countries require the use
of separate recycling collection services.
— iv —
Preface
Main Features
•
Lightweight unit, easy to pack away and transport.
•
Compatible with all major video standards including NTSC, PAL, and SECAM.
•
A high brightness rating allows for presentations in daylight or in lit rooms.
•
Supports resolutions up to UXGA at 16.7 million colors to deliver crisp, clear images.
•
Flexible setup allows for front, rear projections.
•
Line-of-vision projections remain square, with advanced keystone correction for angled
projections.
•
Input source automatically detected.
About this Manual
This manual is intended for end users and describes how to install and operate the DLP projector. Wherever possible, relevant information—such as an illustration and its description—has been kept on one
page. This printer-friendly format is both for your convenience and to help save paper, thereby protecting
the environment. It is suggested that you only print sections that are relevant to your needs.
–v–
DLP Projector—User’s Manual
Table of Contents
GETTING STARTED .......................................................................................................................................................... 1
PACKING CHECKLIST ........................................................................................................................................................... 1
VIEWS OF PROJECTOR PARTS ............................................................................................................................................... 2
Front-right View ............................................................................................................................................................. 2
Top view—On-screen Display (OSD) buttons and LEDs ............................................................................................... 3
Rear view ........................................................................................................................................................................ 4
Bottom view..................................................................................................................................................................... 5
REMOTE CONTROL PARTS ................................................................................................................................................... 6
REMOTE CONTROL OPERATING RANGE ............................................................................................................................... 8
PROJECTOR AND REMOTE CONTROL BUTTONS .................................................................................................................... 8
SETUP AND OPERATION................................................................................................................................................. 9
INSERTING THE REMOTE CONTROL BATTERIES ................................................................................................................... 9
CONNECTING INPUT DEVICES ............................................................................................................................................ 10
STARTING AND SHUTTING DOWN THE PROJECTOR ............................................................................................................. 11
SETTING AN ACCESS PASSWORD (SECURITY LOCK) .......................................................................................................... 13
ADJUSTING THE PROJECTOR LEVEL ................................................................................................................................... 15
ADJUSTING THE ZOOM, FOCUS AND KEYSTONE ................................................................................................................ 16
ADJUSTING THE VOLUME .................................................................................................................................................. 17
ON-SCREEN DISPLAY (OSD) MENU SETTINGS....................................................................................................... 18
OSD MENU CONTROLS ..................................................................................................................................................... 18
Navigating the OSD ...................................................................................................................................................... 18
SETTING THE OSD LANGUAGE .......................................................................................................................................... 19
OSD MENU OVERVIEW ..................................................................................................................................................... 20
OSD SUB-MENU OVERVIEW ............................................................................................................................................. 21
IMAGE MENU ..................................................................................................................................................................... 22
Advanced Feature ......................................................................................................................................................... 23
Color Manager.............................................................................................................................................................. 24
COMPUTER MENU.............................................................................................................................................................. 25
VIDEO/AUDIO MENU ......................................................................................................................................................... 26
Audio............................................................................................................................................................................. 27
INSTALLATION I MENU ...................................................................................................................................................... 28
Advanced Feature ......................................................................................................................................................... 29
Presentation Timer........................................................................................................................................................ 30
INSTALLATION II MENU..................................................................................................................................................... 31
Advanced Feature ......................................................................................................................................................... 32
OSD Menu Setting......................................................................................................................................................... 33
Peripheral Test.............................................................................................................................................................. 33
Lamp Hour Reset .......................................................................................................................................................... 34
3D ................................................................................................................................................................................. 34
Network......................................................................................................................................................................... 35
Factory Reset ................................................................................................................................................................ 40
Status............................................................................................................................................................................. 40
U
MAINTENANCE AND SECURITY................................................................................................................................. 41
REPLACING THE PROJECTION LAMP................................................................................................................................... 41
Resetting the Lamp........................................................................................................................................................ 43
CLEANING THE PROJECTOR................................................................................................................................................ 44
Cleaning the Lens ......................................................................................................................................................... 44
Cleaning the Case ......................................................................................................................................................... 44
USING THE KENSINGTON® LOCK ....................................................................................................................................... 45
Using the Kensington® Lock ......................................................................................................................................... 45
Using the Security Bar .................................................................................................................................................. 45
TROUBLESHOOTING ..................................................................................................................................................... 46
COMMON PROBLEMS AND SOLUTIONS ............................................................................................................................... 46
TIPS FOR TROUBLESHOOTING ............................................................................................................................................ 46
— vi —
Preface
LED ERROR MESSAGES ..................................................................................................................................................... 47
IMAGE PROBLEMS .............................................................................................................................................................. 47
LAMP PROBLEMS ............................................................................................................................................................... 48
REMOTE CONTROL PROBLEMS .......................................................................................................................................... 48
AUDIO PROBLEMS ............................................................................................................................................................. 48
HAVING THE PROJECTOR SERVICED .................................................................................................................................. 48
HDMITM Q & A................................................................................................................................................................. 49
SPECIFICATIONS............................................................................................................................................................. 50
SPECIFICATIONS................................................................................................................................................................. 50
PROJECTION DISTANCE VS. PROJECTION SIZE .................................................................................................................... 52
Projection Distance and Size Table .............................................................................................................................. 52
TIMING MODE TABLE ........................................................................................................................................................ 55
PROJECTOR DIMENSIONS ................................................................................................................................................... 57
REGULATORY COMPLIANCE ..................................................................................................................................... 58
FCC WARNING .................................................................................................................................................................. 58
CANADA ............................................................................................................................................................................ 58
SAFETY CERTIFICATIONS ................................................................................................................................................... 58
APPENDIX I ....................................................................................................................................................................... 59
RS-232C PROTOCOL.......................................................................................................................................................... 59
– vii –
DLP Projector – User’s Manual
GETTING STARTED
Packing Checklist
Carefully unpack the projector and check that the following items are included:
DLP PROJECTOR WITH LENS CAP
REMOTE CONTROL
(WITH TWO AAA BATTERIES)
CARRYING CASE
RGB CABLE
CD-ROM
(THIS USER’S MANUAL)
QUICK START GUIDE
POWER CORD
WARRANTY CARD
Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work. It
is recommend that you keep the original packing material should you ever need to return the equipment
for warranty service.
Caution:
Avoid using the projector in dusty environments.
–1–
DLP Projector—User’s Manual
Views of Projector Parts
Front-right View
23
1
ITEM
4 5
LABEL
67
DESCRIPTION
1.
IR receiver
Receive IR signal from remote control
2.
Height-adjuster button
Push to release height adjuster
3.
Height adjuster
Adjusts level of projector
4.
Lens
Projection Lens
5.
Focus ring
Focuses the projected image
6.
Zoom ring (*)
Enlarges the projected image
7.
Function keys
See Top view—On-screen Display (OSD) buttons
and LEDs.
SEE PAGE:
6
15
16
3
Note: (*)Not available in some models.
Important:
Ventilation openings on the projector allow for good air circulation, which keeps the projector lamp
cool. Do not obstruct any of the ventilation openings.
–2–
DLP Projector – User’s Manual
Top view—On-screen Display (OSD) buttons and LEDs
10
5
MENU
AU TO
2
SOUR CE
4
3
12
9
1
11
ITEM
1.
TEMP
POWER
LAMP
6
8
7
LABEL
(POWER)
DESCRIPTION
11
10
SOURCE
Detects the input device
3.
AUTO
Optimizes image size, position, and resolution
4.
▲ (Up cursor) /
KEYSTONE
Navigates and changes settings in the OSD
Quick Menu – For Keystone
5.
► (Right cursor)
Navigates and changes settings in the OSD
6.
TEMP LED
7.
LAMP LED
POWER LED
On
System over temperature
Off
Normal State
On
Lamp Error.
Off
Normal State
Green
Power On
Off
Power Off (AC Off)
Flashing
System Initialized / Cooling / Error code
9.
▼ (Down cursor) /
KEYSTONE
Navigates and changes settings in the OSD
Quick Menu – For Keystone
10.
MENU
Open and exits the OSD buttons
11.
◄ (Left cursor)
Navigates and changes settings in the OSD
12.
Enter
PAGE:
Turns the projector On or Off
2.
8.
SEE
Changes settings in the OSD
–3–
18
18
18
DLP Projector—User’s Manual
Rear view
1
3 4 567
2
8
9
10
11
12 13 14 15
ITEM
1.
LABEL
AC IN
2.
DESCRIPTION
Connect the POWER CABLE
(USB)
16 17
SEE PAGE:
11
Connect the USB CABLE from a computer
3.
12V TRIGGER (*)
Connect the DC 12V OUT
4.
LAN
Connect a LAN CABLE from Ethernet
5.
VIDEO IN
Connect the COMPOSITE CABLE from a video device
6.
AUDIO IN (L and R)
Connect the AUDIO CABLES from a audio device
7.
AUDIO IN – 1
Connect an AUDIO CABLE from the input device
8.
VGA OUT
Connect the RGB CABLE to a display
9.
VGA IN
Connect the RGB CABLE from a computer and components
10.
DVI
Connect the DVI CABLE to a display
11.
HDMITM (*)
Connect the HDMITM CABLE from a HDMITM device
12.
AUDIO IN – 2 (*)
Connect an AUDIO CABLE from the input device
13.
RS-232C
Connect RS-232 serial port cable for remote control
14.
AUDIO OUT
Connect an AUDIO CABLE for audio loop through
15.
MIC
Connect the Microphone input device
16.
Kensington Lock
Secure to permanent object with a Kensington® Lock system
17.
IR receiver
Receive IR signal from remote control
10
Note: (*)Not available in some models.
–4–
45
DLP Projector – User’s Manual
Bottom view
1
2
1
ITEM
LABEL
4 3
DESCRIPTION
SEE PAGE:
1.
Ceiling support holes
Contact your dealer for information on mounting the projector on a ceiling
2.
Tilt adjustor
Rotate adjuster lever to adjust angle position.
3.
Height adjustor
Adjuster drops down when adjuster button is pushed.
4.
Height adjustor button
Push to release adjustor.
15
15
Note:
When installing, ensure that you use only UL Listed ceiling mounts.
For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw
depth of 12 mm (0.47 inch).
The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount
load capacity must exceed the weight of the installed equipment, and as an additional precaution
be capable of withstanding three times the weight of the equipment (not less than 5.15 kg) over a
period of 60 seconds.
–5–
DLP Projector—User’s Manual
Remote Control Parts
Important:
1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluorescent lights can disrupt remote control operation.
2. Be sure nothing obstructs the path between the remote control and the projector. If the path between the remote control and the projector is obstructed, you can bounce the signal off certain
reflective surfaces such as projector screens.
3. The buttons and keys on the projector have the same functions as the corresponding buttons on
the remote control. This user’s manual describes the functions based on the remote control.
–6–
DLP Projector – User’s Manual
ITEM
LABEL
DESCRIPTION
1.
IR transmitter
Transmits signals to projector
2.
Status LED
Lights when the remote control is used
3.
Laser
Press to operate the on-screen pointer
4.
Up
Up arrow when connected through USB to a PC
5.
Right
Right arrow when connected through USB to a PC
6.
Down
Down arrow when connected through USB to a PC
7.
Page Down
Page down when connected through USB to a PC
8.
Up cursor
9.
Right cursor
10.
Down cursor
11.
SEE PAGE:
Navigates and changes settings in the OSD
18
Volume +/-
Adjusts volume
17
12.
Mute
Mutes the built-in speaker
13.
Zoom+
Zoom in
14.
Zoom-
Zoom out
15.
Freeze
Freeze/unfreezes the on-screen picture
16.
Blank
Makes the screen blank
17.
Source
Detects the input device
18.
Auto
Auto adjustment for phase, tracking, size, position
19.
Menu
Opens the OSD
18
20.
Status
Opens the OSD Status menu (the menu only opens when an
input device is detected)
40
21.
Keystone top/bottom
Corrects image-trapezoid (wider top/bottom) effect
16
22.
Left cursor
Navigates and changes settings in the OSD
23.
Enter
Changes settings in the OSD
24.
Page Up
Page up when connected through USB to a PC
25.
Left
Left arrow when connected through USB to a PC
26.
Enter
Enter key when connected through USB to a PC
27.
Power
Turns the projector on or off
28.
Laser
Use as on-screen pointer. DO NOT POINT IN EYES.
–7–
18
11
DLP Projector—User’s Manual
Remote Control Operating Range
The remote control uses infrared transmission to control the projector. It is not necessary to point the
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or
the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and
15 degrees above or below the projector level. If the projector does not respond to the remote control,
move a little closer.
Projector and Remote Control Buttons
The projector can be operated using the remote control or the buttons on the top of the projector. All
operations can be carried out with the remote control; however, the buttons on the projector are limited in use.
–8–
DLP Projector – User’s Manual
SETUP AND OPERATION
Inserting the Remote Control Batteries
1.
2.
3.
Remove the battery compartment cover
by sliding the cover in the direction of
the arrow.
Insert the battery with the positive side
facing up.
Replace the cover.
Caution:
1. Only use AAA batteries (Alkaline batteries are recommended).
2. Dispose of used batteries according to local ordinance regulations.
3. Remove the batteries when not using the projector for prolonged periods.
–9–
DLP Projector—User’s Manual
Connecting Input Devices
A PC or notebook computer and video devices can be connected to the projector at the same time. Video
devices include DVD, VCD, and VHS players, as well as movie camcorders and digital still cameras.
Check the user manual of the connecting device to confirm it has the appropriate output connector.
A
B
C
D E F
K
ITEM
LABEL
A
(USB)
H
G
L
M
I
J
N
DESCRIPTION
Connect the USB CABLE from a computer
B
12V TRIGGER (*)
Connect the DC 12V OUT
C
LAN
Connect a LAN CABLE from Ethernet
D
VIDEO IN
Connect the COMPOSITE CABLE from a video device
E
AUDIO IN (L and R)
Connect the AUDIO CABLES from a audio device
F
AUDIO IN -1
Connect an AUDIO CABLE from the input device
G
VGA OUT
Connect the RGB CABLE to a display (Loop Thru only for VGA IN-1)
H
VGA IN
Connect the RGB CABLE from a computer and components
I
DVI
Connect the DVI CABLE to a display
J
HDMITM (*)
Connect the HDMITM CABLE from a HDMITM device
K
AUDIO IN -2 (*)
Connect an AUDIO CABLE from the input device
L
RS-232C
Connect the RS-232 serial cable for remote control
M
AUDIO OUT
Connect an AUDIO CABLE for audio loop through
N
MIC
Connect the Microphone input device
Note:
(*)Not available in some models.
Warning:
As a safety precaution, disconnect all power to the projector and connecting devices before making
connections.
– 10 –
DLP Projector – User’s Manual
Starting and Shutting down the Projector
1.
2.
3.
Connect the power cord to the projector.
Connect the other end to a wall outlet.
The
POWER LED on the projector
light.
Turn on the connected devices.
Ensure the LAMP LED not a flashing
POWER
orange. Then press the
button to turn on the projector.
The projector splash screen displays and
connected devices are detected.
See Setting an Access Password
(Security Lock) on page 13 if security
lock is enabled.
4.
If more than one input device is connected, press the SOURCE button and
use ▲▼ to scroll among devices.
(Component is supported through the
RGB to COMPONENT ADAPTER.)
•
VGA: Analog RGB
Component: DVD input YCbCr / YPbPr, or
HDTV input YPbPr via HD15 connector
•
Composite Video: Traditional composite video
•
DVI: Analog RGB, DVI
•
HDMI: HDMI (Not available in some models.)
– 11 –
DLP Projector—User’s Manual
5.
When the “Power Off? /Press Power
again” message appears, press the
POWER button. The projector turns
off.
Caution:
1. Be sure to remove the lens cap before starting projector.
2. Do not unplug the power cord until the POWER LED stops flashing–indicating the projector has
cooled down.
– 12 –
DLP Projector – User’s Manual
Setting an Access Password (Security Lock)
You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projector.
When enabled, the password must be entered after you power on the projector. (See Navigating the
OSD on page 18 and Setting the OSD Language on page 19 for help on using OSD menus.)
Important:
Keep the password in a safe place. Without the password, you will not be able to use the projector.
If you lose the password, contact your reseller for information on clearing the password.
1.
2.
3.
4.
Press the MENU button to open the OSD
menu.
Press the cursor ◄► button to move to
the Installation I menu, press the cursor
▲▼ button to select Advanced.
Press the cursor ▲▼ button to select
Security Lock.
Press the cursor ◄► button to enable or
disable security lock function.
A password dialog box automatically
appears.
– 13 –
DLP Projector—User’s Manual
5.
You can use the cursor buttons ▲▼◄►
either on keypad or IR remote control for
password entry. You can use any
combination including the same arrow five
times, but not less than five.
Press the cursor buttons in any order to set
the password. Push the MENU button to
exit the dialog box.
6.
The password confirm menu appears when
user presses the power-on key in case the
Security Lock is enabled.
Enter the password in the order you set it
at step 5. In case you forget the password,
please contact the service center.
The service center will validate the owner
and help reset the password.
– 14 –
DLP Projector – User’s Manual
Adjusting the Projector Level
Take note of the following when setting up the projector:
•
The projector table or stand should be level and sturdy.
•
Position the projector so that it is perpendicular to the screen.
•
Ensure the cables are in a safe location. You could trip over them.
D
A
C
1.
To raise the level of the projector, lift the projector [A] and press the height-adjuster
button [B].
The height adjuster drops down [C].
2.
3.
To lower the level of the projector, press the height-adjuster button and push down
on the top of the projector.
To adjust the angle of the picture, turn the tilt-adjuster [D] right or left until the
desired angle has been achieved.
– 15 –
DLP Projector—User’s Manual
Adjusting the Zoom, Focus and Keystone
1.
2.
Use the Image-zoom
control (on the projector
only) to resize the projected image and screen
size B .(*)
B
A
Use the Image-focus
control (on the projector
only) to sharpen the projected image A .
C
MENU
Use the KEYSTONE
buttons (on the projector
or the remote control) to
correct image-trapezoid
(wider top or bottom)
effect.
AU TO
SOUR CE
3.
Volume
-
+
TEMP
POWER
LAMP
Remote control and OSD panel
4.
The keystone control
appears on the display.
Note: (*)Not available in some models.
– 16 –
DLP Projector – User’s Manual
Adjusting the Volume
1.
Press the Volume +/buttons on the remote
control.
The volume control
appears on the display.
Volume
-
+
MENU
SOUR CE
Press the Left or Right
Cursor buttons on the
keypad to adjust Volume
+/-.
TEMP
3.
Press the MUTE button to
turn off the volume (This
feature is available only
on the remote).
– 17 –
AU TO
2.
POWER
LAMP
DLP Projector—User’s Manual
ON-SCREEN DISPLAY (OSD) MENU SETTINGS
OSD Menu Controls
The projector has an OSD that lets you make image adjustments and change various settings.
Navigating the OSD
You can use the remote control cursor buttons or the buttons on the top of the projector to navigate
and make changes to the OSD. The following illustration shows the corresponding buttons on the
projector.
5
4
MENU
1
4
3
2
AU TO
SOUR CE
1
2
Volume
-
5
+
Mute
3
TEMP
POWER
LAMP
1. To enter the OSD, press the
MENU button.
2. There are five menus. Press
the cursor ◄► button to
move through the menus.
3. Press the cursor ▲▼ button
to move up and down in a
menu.
4. Press ◄► to change values
for settings.
5. Press MENU to close the
OSD or leave a submenu.
Note:
Depending on the video source, not all items in the OSD are available. For example, the Horizontal/Vertical Position items in the Computer menu can only be modified when connected to a PC.
Items that are not available cannot be accessed and are grayed out.
– 18 –
DLP Projector – User’s Manual
Setting the OSD Language
Set the OSD language to your preference before continuing.
1. Press the MENU button. Press the cursor ◄► button to navigate to Installation I.
2. Press the cursor ▲▼ button until Language is highlighted.
3. Press the cursor ◄► button until the language you want is highlighted.
4. Press the MENU button twice to close the OSD.
– 19 –
DLP Projector—User’s Manual
OSD Menu Overview
Use the following illustration to quickly find a setting or determine the range for a setting.
– 20 –
DLP Projector – User’s Manual
OSD Sub-Menu Overview
Note:
(*)Not available in some models.
– 21 –
DLP Projector—User’s Manual
Image Menu
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Image
Menu. Press the cursor ▲▼ button to move up and down in the Image menu. Press ◄► to change
values for settings.
ITEM
DESCRIPTION
Display Mode
Press the cursor ◄► button to set the Display Mode.
Brilliant Color
Press the cursor ◄► button to adjust the Brilliant Color value.
Brightness
Press the cursor ◄► button to adjust the display brightness.
Contrast
Press the cursor ◄► button to adjust the display contrast.
Sharpness
Press the cursor ◄► button to adjust the display sharpness level.
Gamma
Press the cursor ◄► button to adjust the gamma correction of the display.
Advanced
Press
(Enter) / ► to enter the Advanced menu. See Advanced Feature on page 23.
Reset
Press
(Enter) / ► to reset all settings to default values.
– 22 –
DLP Projector – User’s Manual
Advanced Feature
Press the Menu button to open the OSD menu. Press ◄► to move to the Image menu. Press ▼▲
to move to the Advanced menu and then press Enter or ►. Press ▼▲ to move up and down in the
Advanced menu.
ITEM
DESCRIPTION
Color Space
Press the cursor ◄► button to adjust the color space.
(Range: Auto – RGB – YPbPr – YCbCr)
Color Temperature
Press the cursor ◄► button to adjust the color temperature.
(Range: Cold – Normal – Warm)
Color Manager
Press
(Enter) / ► to enter the color manager menu. (Range: Red-Green-Blue-CyanMagenta-Yellow-White). See page 24 for more information on Color Manager.
– 23 –
DLP Projector—User’s Manual
Color Manager
Press
(Enter) / ► to enter the Color Manager sub menu.
ITEM
DESCRIPTION
Red
Select to enter the Red Color Manager.
Press the ◄► buttons to adjust the Hue, Saturation, and Gain.
Green
Select to enter the Green Color Manager.
Press the ◄► buttons to adjust the Hue, Saturation, and Gain.
Blue
Select to enter the Blue Color Manager.
Press the ◄► buttons to adjust the Hue, Saturation, and Gain.
Cyan
Select to enter the Cyan Color Manager.
Press the ◄► buttons to adjust the Hue, Saturation, and Gain.
Magenta
Select to enter the Magenta Color Manager.
Press the ◄► buttons to adjust the Hue, Saturation, and Gain.
Yellow
Select to enter the Yellow Color Manager.
Press the◄► buttons to adjust the Hue, Saturation, and Gain.
White
Select to enter the White Color Manager.
Press the ◄► buttons to adjust the Red, Green, and Blue.
– 24 –
DLP Projector – User’s Manual
Computer Menu
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Computer menu. Press the cursor ▲▼ button to move up and down in the computer menu. Press ◄► to
change values for settings.
ITEM
DESCRIPTION
Horizontal Position
Press the cursor ◄► button to adjust the display position to left or right.
Vertical Position
Press the cursor ◄► button to adjust the display position to up or down.
Frequency
Press the cursor ◄► button to adjust the A/D sampling clock.
Tracking
Press the cursor ◄► button to adjust the A/D sampling dot.
Auto Image
Press
(Enter) / ► to automatically adjustment for phase, tracking, size and position.
– 25 –
DLP Projector—User’s Manual
Video/Audio Menu
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the
Video/Audio menu. Press the cursor ▲▼ button to move up and down in the Video/Audio menu.
Press ◄► to change values for settings.
ITEM
DESCRIPTION
Video AGC
Press the ◄► buttons to enable or disable the Automatic Gain Control for video source.
Video Saturation
Press the ◄► buttons to adjust the video saturation.
Video Tint
Press the ◄► buttons to adjust the video tint/hue.
Film Mode
Press the ◄► buttons to select a different film mode.
Video Overscan
Press the ◄► buttons to enable or disable video over scan.
Closed Captioning
Press the ◄► buttons to enable or disable Closed Captioning
Audio
Press
(Enter) / ► to enter the Audio menu. See Audio on page 27.
Reset
Press
(Enter) / ► to reset all settings to default values.
Note:
Video jagging may occur when playing interlace video. To overcome this issue, open the
Video / Audio menu and adjust the Film Mode feature.
– 26 –
DLP Projector – User’s Manual
Audio
Press
(Enter) / ► to enter the Audio sub menu.
ITEM
DESCRIPTION
Volume
Press the ◄► buttons to adjust the audio volume.
(Range: 0~8)
Mute
Press the ◄► buttons to turn on or off the speaker.
Audio Input
Press the cursor ◄► button to select audio input.
(Range: Mini ~ RCA)
– 27 –
DLP Projector—User’s Manual
Installation I Menu
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Installation I menu. Press the cursor ▲▼ button to move up and down in the Installation I menu. Press
◄► to change values for settings.
ITEM
DESCRIPTION
Language
Press the cursor ◄► button to select a different localization Menu.
Blank Screen
Press the cursor ◄► button to select different color to blank the screen.
Projection
Press the cursor ◄► button to choose from four projection methods:
Aspect Ratio
Press the cursor ◄► button to adjust the video aspect ratio.
Keystone
Press the cursor ◄► button to adjust the display keystone.
Digital Zoom
Press the cursor ◄► button to adjust the Digital Zoom menu. (Range: -10 ~ +10)
Advanced
Press
Reset
(Enter) / ► to reset all settings to default values
Press
(expect Language and Security Lock).
(Enter) / ► to enter the Advanced menu. See Advanced Feature on page 32.
– 28 –
DLP Projector – User’s Manual
Advanced Feature
Press the Menu button to open the OSD menu. Press ◄► to move to the Installation I menu. Press
▲▼ to move to the Advanced menu and then press Enter or ►. Press ▲▼ to move up and down in
the Advanced menu. Press ◄► to change values for setting.
ITEM
DESCRIPTION
Security Lock
Press the cursor ◄► button to enable or disable security lock function.
Keypad Lock
Press the cursor ◄► button to enable or disable keypad lock function.
Wall Color
Press the cursor ◄► button to select different wall color setting.
Presentation Timer
Press
Projector ID
Press the cursor ◄► button to adjust a two digit projector ID from 0 through 99.
Auto Keystone
Press the cursor ◄► button to enable or disable auto keystone function.
(Enter) / ► to enter the Presentation menu. See Presentation Timer on page 30.
– 29 –
DLP Projector—User’s Manual
Presentation Timer
The Presentation Timer function can indicate the presentation time on the screen to help you achieve
better time management when giving presentations.
Press
(Enter) / ► to enter the Presentation Timer sub menu.
ITEM
DESCRIPTION
Timer
Press the cursor ◄► button to enable or disable presentation timer function.
Timer Period
Press the cursor ◄► button to adjust the display timer period.
Timer Reset
Press
(Enter) / ► to reset presentation timer counter.
– 30 –
DLP Projector – User’s Manual
Installation II Menu
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Installation II menu. Press the cursor ▲▼ button to move up and down in the Installation II menu.
ITEM
DESCRIPTION
Auto Source
Press the cursor ◄► button to enable or disable automatic source detection. (Range: On ~ Off)
Auto Power Off
(min.)
Press the cursor ◄► button to enable or disable automatic shutdown of lamp when no signal.
Auto Power On
Press the cursor ◄► button to enable or disable automatic power On when AC power is supplied.
Fan Speed
Press the cursor ◄► button to toggle between Normal and High fan speeds.
Note: We recommend selecting high speed in high temperatures, high humidity, or high
altitude areas.
Lamp Mode
Press the cursor ◄► button to select the lamp mode for higher brightness or lower brightness
to save lamp life.
Advanced
Press
(Enter) / ► to enter the Advanced menu. See Advanced Feature on page 32.
Factory Reset
Press
(Enter) / ► to reset all items to factory preset values.
Status
Press
(Enter) / ► to enter the Status menu. See page 40 for more information on Status.
– 31 –
DLP Projector—User’s Manual
Advanced Feature
Press the Menu button to open the OSD menu. Press ◄► to move to the Installation II menu.
Press ▲▼ to move to the Advanced menu and then press Enter or ►. Press ▲▼ to move up and
down in the Advanced menu. Press ◄► to change values for setting.
ITEM
DESCRIPTION
OSD Menu Setting
Press Enter / ► to enter the OSD setting menu. See page 33 for more information on OSD
Menu Setting.
Peripheral Test
Press Enter/ ► to enter the Peripheral Test menu. See page 33 for more information on
Peripheral Test.
Lamp Hour Reset
After replacing the lamp, this item should be reset. See page 34 for more information on Lamp
Hour Reset.
Low Power Mode
Press ◄► to turn Low Power Mode on or off.
3D
Press
RS232
Press ◄► to select RS232 (remote) or Network (LAN) mode depending on projector connection method.
Network
Press
(Enter) / ► to enter the Network menu. See page 35 for more information on
Network.
Enter/ ► to enter the 3D menu. See page 34 for more information on 3D setting..
Note:
To enjoy the 3D function, first enable the Play Movie in 3D setting found in your DVD
device under the 3D Disc Menu.
– 32 –
DLP Projector – User’s Manual
OSD Menu Setting
ITEM
DESCRIPTION
Menu Position
Press ◄► button to select different OSD location.
Translucent Menu
Press ◄► button to select OSD background translucent level.
Menu Display
Press ◄► button to select OSD timeout delay.
Peripheral Test
ITEM
DESCRIPTION
Remote Control Test
Press
(Enter) / ► to test the IR remote controller for diagnostic.
Color Test
Press
(Enter) / ► to select different colors on screen.
Button Test
Press
(Enter) / ► to test the button on keypad.
USB Test
Press
(Enter) / ► to test the USB connection with connected PC.
– 33 –
DLP Projector—User’s Manual
Lamp Hour Reset
Please refer to Resetting the Lamp on page 43 to reset the lamp hour counter.
3D
ITEM
DESCRIPTION
3D
Press ◄► to select Off, DLP-Link or IR.
3D Sync Invert
Press ◄► to turn 3D Sync Invert On or Off.
– 34 –
DLP Projector – User’s Manual
Network
ITEM
Network State
DESCRIPTION
Displays the network connection status.
Press ◄► to turn DHCP On or Off.
DHCP
Note: If you select DHCP Off, complete the IP Address, Subnet Mask, Gateway, and DNS
fields.
IP Address
Enter a valid IP address if DHCP is turned off.
Subnet Mask
Enter a valid Subnet Mask if DHCP is turned off.
Gateway
Enter a valid Gateway address if DHCP is turned off.
DNS
Enter a valid DNS name if DHCP is turned off.
Apply
Press
(Enter) / ► to confirm settings.
– 35 –
DLP Projector—User’s Manual
For simplicity and ease of operation, the projector provides diverse networking and remote management
features.
The LAN/RJ45 function of the projector through a network, such as remotely manage: Power On/Off,
Brightness and Contrast settings. Also, projector status information, such as: Video-Source, Sound-Mute,
etc.
LAN_RJ45
1. Connect an RJ45 cable to RJ45 ports on the projector and the PC (Laptop).
2. On the PC (Laptop), select Start → Control Panel → Network Connections.
– 36 –
DLP Projector – User’s Manual
3. Right-click on Local Area Connection, and select Properties.
4. In the Properties window, select the General tab, and select Internet Protocol (TCP/IP).
5. Click Properties.
6. Click Use the following IP address and fill in the IP address and Subnet mask, then click OK.
– 37 –
DLP Projector—User’s Manual
7. Press the Menu button on the projector.
8.
Select Installation II → Advanced → Network.
9.
After getting into Network, input the following:
` DHCP: Off
` IP Address: 10.10.10.10
` Subnet Mask: 255.255.255.0
` Gateway: 0.0.0.0
` DNS Server: 0.0.0.0
10. Press
(Enter) / ► to confirm settings.
Open a web browser
(for example, Microsoft Internet Explorer with Adobe Flash Player 9.0 or higher).
11. In the Address bar, input the IP address: 10.10.10.10.
12. Press
(Enter) / ►.
The projector is setup for remote management. The LAN/RJ45 function displays as follows.
– 38 –
DLP Projector – User’s Manual
CATEGORY
Crestron Control
Projector
Network Configuration
User Password
Admin Password
ITEM
INPUT-LENGTH
IP Address
14
IP ID
2
Port
5
Projector Name
10
Location
9
Assigned To
8
DHCP (Enabled)
(N/A)
IP Address
15
Subnet Mask
15
Default Gateway
15
DNS Server
15
Enabled
(N/A)
New Password
15
Confirm
15
Enabled
(N/A)
New Password
15
Confirm
15
For more information, please visit http://www.crestron.com.
– 39 –
DLP Projector—User’s Manual
Factory Reset
Press the cursor ▲▼ button to move up and down in the Installation II menu. Select the Factory
(Enter) / ► to reset all the menu items to the factory default values
Reset sub menu and press
(expect Language and Security Lock).
Status
Press the cursor ▲▼ button to move up and down in the Installation II menu. Select the
(Enter) / ► to enter the Status sub menu.
Installation II sub menu and press
ITEM
DESCRIPTION
Active Source
Display the activated source.
Video Information
Displays resolution/video information for RGB source and color standard for Video source.
Lamp Hours
Lamp hour used information is displayed. Eco and Normal counters are separated.
– 40 –
DLP Projector – User’s Manual
MAINTENANCE AND SECURITY
Replacing the Projection Lamp
The projection lamp should be replaced when it burns out. It should only be replaced with a certified
replacement part, which you can order from your local dealer.
Important:
a. The projection lamp used in this product contains a small amount of mercury.
b. Do not dispose this product with general household waste.
c. Disposal of this product must be carried out in accordance with the regulations of your local
authority.
Warning:
Be sure to turn off and unplug the projector at least 30 minutes before replacing the lamp. Failure to
do so could result in a severe burn.
1.
2.
Loosen the single screw on
the lamp compartment cover.
Remove the lamp compartment cover.
– 41 –
DLP Projector—User’s Manual
3.
Remove the three screws
from the lamp module.
4.
Lift the module handle up.
5.
Pull firmly on the module
handle to remove the lamp
module.
steps 1 to 5 to install
6. GReverse
the new lamp module.
While installing, align the
lamp module with the
connector and ensure it is
level to avoid damage.
Note: The lamp module must
sit securely in place and the
lamp connector must be connected properly before
tightening the screws.
– 42 –
DLP Projector – User’s Manual
Resetting the Lamp
After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following:
1.
2.
3.
4.
Press the MENU button to open the
OSD menu.
Press the cursor ◄► button to move
to the Installation II menu. Press the
cursor button to move down to
Advanced.
Press the cursor ▼▲ button to move
down to Lamp Hour Reset.
Press the cursor ► or Enter button.
A message screen appears.
5.
6.
Press ▼▲◄► buttons to reset the
lamp hour.
Press the MENU button to get back
to Installation II.
– 43 –
DLP Projector—User’s Manual
Cleaning the Projector
Cleaning the projector to remove dust and grime will help ensure trouble-free operation.
Warning:
1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do so
could result in a severe burn.
2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings
on the projector.
3. If a little water gets into the projector interior while cleaning, leave unplugged in a well-ventilated
room for several hours before using.
4. If a lot of water gets into the projector interior when cleaning, have the projector serviced.
Cleaning the Lens
You can purchase optic lens cleaner from most camera stores. Refer to the following to clean the projector lens.
1. Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly to the lens.)
2. Lightly wipe the lens in a circular motion.
Caution:
1. Do not use abrasive cleaners or solvents.
2. To prevent discoloration or fading, avoid getting cleaner on the projector case.
Cleaning the Case
Refer to the following to clean the projector case.
1. Wipe off dust with a clean dampened cloth.
2. Moisten the cloth with warm water and mild detergent (such as used to wash dishes), and then wipe
the case.
3. Rinse all detergent from the cloth and wipe the projector again.
Caution:
To prevent discoloration or fading of the case, do not use abrasive alcohol-based cleaners.
– 44 –
DLP Projector – User’s Manual
Using the Kensington® Lock
Using the Kensington® Lock
If you are concerned about security, attach the projector to a permanent object with the Kensington
slot and a security cable.
Note:
Contact your vendor for details on purchasing a suitable Kensington security cable.
The security lock corresponds to Kensington’s MicroSaver Security System. If you have any comment, contact: Kensington, 2853 Campus Drive, San Mateo, CA 94403, U.S.A. Tel: 800-535-4242,
http://www.Kensington.com.
Using the Security Bar
In addition to the password protection function and the Kensington lock, the Security Bar helps protect the projector from unauthorized removal. See the following picture.
– 45 –
DLP Projector—User’s Manual
TROUBLESHOOTING
Common problems and solutions
These guidelines provide tips to deal with problems you may encounter while using the projector. If
the problem remains unsolved, contact your dealer for assistance.
Often after time spent troubleshooting, the problem is traced to something as simple as a loose connection. Check the following before proceeding to the problem-specific solutions.
•
Use some other electrical device to confirm that the electrical outlet is working.
•
Ensure the projector is turned on.
•
Ensure all connections are securely attached.
•
Ensure the attached device is turned on.
•
Ensure a connected PC is not in suspending mode.
•
Ensure a connected notebook computer is configured for an external display.
(This is usually done by pressing an Fn-key combination on the notebook.)
Tips for Troubleshooting
In each problem-specific section, try the steps in the order suggested. This may help you to solve the
problem more quickly.
Try to pin point the problem and thus avoid replacing non-defective parts.
For example, if you replace batteries and the problem remains, put the original batteries back and go
to the next step.
Keep a record of the steps you take when troubleshooting: The information may be useful when calling for technical support or for passing on to service personnel.
– 46 –
DLP Projector – User’s Manual
LED Error Messages
POWER LED
BLINK
OVER TEMP
LED
LAMP LED
BLINK
ON
0
0
Over temperature
0
ON
0
Thermal break status error
4
0
0
Lamp error
0
0
ON
Fan1 error
6
0
1
Fan2 error
6
0
2
Fan3 error
6
0
3
Lamp door open
7
0
0
DMD error
8
0
0
Color wheel error
9
0
0
ERROR CODE MESSAGES
Standby mode
In the event of an error, please disconnect the AC power cord and wait for one (1) minute before restarting
the projector. If the Power or Lamp LEDs are still blinking or the Over Temp LED is lit, or any other situation that isn't listed in the chart above, please contact your service center.
Image Problems
Problem: No image appears on the screen
1. Verify the settings on your notebook or desktop PC.
2. Turn off all equipment and power up again in the correct order.
Problem: The image is blurred
1. Adjust the Focus on the projector.
2. Press the Auto button on the remote control or projector.
3. Ensure the projector-to-screen distance is within the 10-meter (33-feet) specified range.
4. Check that the projector lens is clean.
Problem: The image is wider at the top or bottom (trapezoid effect)
1. Position the projector so it is as perpendicular to the screen as possible.
2. Use the Keystone button on the remote control or projector to correct the problem.
Problem: The image is reversed
Check the Projection setting on the Installation I menu of the OSD.
Problem: The image is streaked
1. Set the Frequency and Tracking settings on the Computer menu of the OSD to the default settings.
2. To ensure the problem is not caused by a connected PC’s video card, connect to another
computer.
Problem: The image is flat with no contrast
Adjust the Contrast setting on the Image menu of the OSD.
Problem: The color of the projected image does not match the source image.
Adjust the Color Temperature and Gamma settings on the Image menu of the OSD.
– 47 –
DLP Projector—User’s Manual
Lamp Problems
Problem: There is no light from the projector
1. Check that the power cable is securely connected.
2. Ensure the power source is good by testing with another electrical device.
3. Restart the projector in the correct order and check that the Power LED is green.
4. If you have replaced the lamp recently, try resetting the lamp connections.
5. Replace the lamp module.
6. Put the old lamp back in the projector and have the projector serviced.
Problem: The lamp goes off
1. Power surges can cause the lamp to turn off. Re-plug power cord. When the Power LED
is on, press the power button.
2. Replace the lamp module.
3. Put the old lamp back in the projector and have the projector serviced.
Remote Control Problems
Problem: The projector does not respond to the remote control
1. Direct the remote control towards remote sensor on the projector.
2. Ensure the path between remote and sensor is not obstructed.
3. Turn off any fluorescent lights in the room.
4. Check the battery polarity.
5. Replace the batteries.
6. Turn off other Infrared-enabled devices in the vicinity.
7. Have the remote control serviced.
Audio Problems
Problem: There is no sound
1. Adjust the volume on the remote control.
2. Adjust the volume of the audio source.
3. Check the audio cable connection.
4. Test the source audio output with other speakers.
5. Have the projector serviced.
Problem: The sound is distorted
1. Check the audio cable connection.
2. Test the source audio output with other speakers.
3. Have the projector serviced.
Having the Projector Serviced
If you are unable to solve the problem, you should have the projector serviced. Pack the projector in
the original carton. Include a description of the problem and a checklist of the steps you took when
trying to fix the problem: The information may be useful to service personnel. For servicing, return the
projector to the place you purchased it.
– 48 –
DLP Projector – User’s Manual
HDMITM Q & A
Q. What is the difference between a “Standard” HDMITM cable and a “High-Speed”
HDMITM cable?
Recently, HDMITM Licensing, LLC announced that cables would be tested as Standard or
High-Speed cables.
․Standard (or “category 1”) HDMITM cables have been tested to perform at speeds of 75Mhz
or up to 2.25Gbps, which is the equivalent of a 720p/1080i signal.
․High Speed (or “category 2”) HDMITM cables have been tested to perform at speeds of
340Mhz or up to 10.2Gbps, which is the highest bandwidth currently available over an
HDMITM cable and can successfully handle 1080p signals including those at increased color
depths and/or increased refresh rates from the Source. High-Speed cables are also able to
accommodate higher resolution displays, such as WQXGA cinema monitors (resolution of
2560 x 1600).
Q. How do I run HDMITM cables longer than 10 meters?
There are many HDMITM Adopters working on HDMITM solutions that extend a cable’s effective
distance from the typical 10 meter range to much longer lengths. These companies
manufacture a variety of solutions that include active cables (active electronics built into
cables that boost and extend the cable’s signal), repeaters, amplifiers as well as CAT5/6 and
fiber solutions.
Q. How can I tell if a cable is an HDMITM certified cable?
All HDMITM products are required to be certified by the manufacturer as part of the HDMITM
Compliance Test Specification. However, there may be instances where cables bearing the
HDMITM logo are available but have not been properly tested. HDMI TM Licensing, LLC actively
investigates these instances to ensure that the HDMITM trademark is properly used in the
market. We recommend that consumers buy their cables from a reputable source and a
company that is trusted.
For more detail information check http://www.hdmi.org/learningcenter/faq.aspx#49
– 49 –
DLP Projector—User’s Manual
SPECIFICATIONS
Specifications
Model
D850
D851
D853W
D855ST
D85AA~AE
D85CWA~CWE
D85ESTA~ESTH
Display type
TI DMD 0.55”
TI DMD 0.55”
TI DMD 0.65”
TI DMD 0.55”
Resolution
SVGA 800x600
XGA 1024x768
WXGA 1280x800
XGA 1024x768
1 ~ 10 m
1.5 ~ 10 m
0.5 ~5 m
25.6” ~ 307.6”
40” ~ 306”
37.3” ~ 373”
Projection distance
Projection screen size
Manual Focus/
Fix Zoom
Manual Focus/Manual Zoom
Projection lens
1.2x
Zoom ratio
1.15x
+/- 30 steps
Vertical keystone correction
Front, Rear, Desktop/Ceiling (Rear, Front)
Projection methods
Data compatibility
VGA, SVGA, XGA, SXGA, SXGA+, UXGA, Mac
SDTV/EDTV/ HDTV
480i, 480p, 720p, 1080i, 1080p
Video compatibility
NTSC/NTSC 4.43, PAL (B/G/H/I/M/N/60), SECAM
H-Sync
15, 30 – 90 kHz
V-Sync
43 – 85 Hz
Safety certification
FCC-B, cUL, UL, CE, C-tick, CCC, KC, CB, GOST, NOM, SASO, Taiwan Green Mark
5° ~ 35°C
Operation temperature
306 mm (W) x 206 mm (D) x 104 mm (H)
Dimensions
AC Input
AC Universal 100-240, Typical @ 110VAC (100-240)/+-10%
Typical 280W (Normal) / Typical 240W (Eco)
Power consumption
<1 watts
Stand By
220W (Normal) / 190W (Eco)
Lamp
10W mono speaker
Audio speaker
VGA x 1
DVI-I x 1
Input Terminals
Fix
Composite video x 1
HDMITM x 1
─
AUDIO RCA x 2
Audio Mini-jack x 1
Audio Mini-jack x 2
VGA x 1
Output Terminals
Audio Mini-jack x 1
RS-232C
RJ45
Control Terminals
MIC mini-jack x 1
─
DC 12V screen trigger
USB
Kensington lock / Security Bar
Security
Note: For questions regarding product specifications, please contact your local distributor.
– 50 –
DLP Projector – User’s Manual
Model
Display type
Resolution
Projection distance
Projection screen size
Projection lens
Zoom ratio
D857WT
D85GWTA~GWTE
D859
D85IA~IE
TI DMD 0.65”
TI DMD 0.55”
WXGA 1280x800
XGA 1024x768
0.5 ~ 5 m
1 ~ 10 m
43.8” ~ 438”
30” ~ 300”
Manual Focus/Fix Zoom
Manual Focus/Manual Zoom
Fix
1.2x
+/- 30 steps
Vertical keystone correction
Projection methods
Front, Rear, Desktop/Ceiling (Rear, Front)
Data compatibility
VGA, SVGA, XGA, SXGA, SXGA+, UXGA, Mac
SDTV/EDTV/ HDTV
480i, 480p, 720p, 1080i, 1080p
Video compatibility
NTSC/NTSC 4.43, PAL (B/G/H/I/M/N/60), SECAM
H-Sync
15, 30 – 90 kHz
V-Sync
43 – 85 Hz
Safety certification
FCC-B, cUL, UL, CE, C-tick, CCC, KC, CB, GOST, NOM, SASO, Taiwan Green Mark
5° ~ 35°C
Operation temperature
Dimensions
306 mm (W) x 206 mm (D) x 104 mm (H)
AC Input
AC Universal 100-240, Typical @ 110VAC (100-240)/+-10%
Power consumption
Typical 280W (Normal) /
Typical 230W (Eco)
Typical 290W (Normal) /
Typical 240W (Eco)
<1 watts
Stand By
220W (Normal) / 190W (Eco)
Lamp
10W mono speaker
Audio speaker
VGA x 1
DVI-I x 1
─
Composite video x 1
Input Terminals
HDMITM x 1
AUDIO RCA x 2
Audio Mini-jack x 2
Audio Mini-jack x 1
VGA x 1
Output Terminals
Audio Mini-jack x 1
RS-232C
RJ45
Control Terminals
MIC mini-jack x 1
DC 12V screen trigger
─
USB
Kensington lock / Security Bar
Security
Note: For questions regarding product specifications, please contact your local distributor.
– 51 –
DLP Projector—User’s Manual
Projection Distance vs. Projection Size
Projection Distance and Size Table
D850 / D851 / D85AA~AE
IMAGE DIAGONAL
(INCH)
IMAGE WIDTH
(INCH)
PROJECTION
DISTANCE
(MM)
FROM
IMAGE HIGHT
(INCH)
PROJECTION
DISTANCE
(MM)
TO
OFFSET-A
( MM )
40
32
24
1300
1561
85
60
48
36
1951
2341
127
70
56
42
2276
2731
148
72
57.6
43.2
2341
2809
153
80
64
48
2601
3121
169
84
67.2
50.4
2731
3277
178
90
72
54
2926
3511
191
96
76.85
57.6
3121
3745
203
100
80
60
3251
3901
212
120
96
72
3901
4682
254
135
108
81
4389
5267
286
150
120
90
4877
5852
318
200
160
120
6502
7803
424
– 52 –
DLP Projector – User’s Manual
D853W / D85CWA~CWE
IMAGE DIAGONAL
(INCH)
IMAGE WIDTH
(INCH)
PROJECTION
DISTANCE
(MM)
FROM
IMAGE HIGHT
(INCH)
PROJECTION
DISTANCE
(MM)
TO
OFFSET-A
( MM )
40
33.92
21.20
1310
1516
61
60
50.88
31.80
1964
2275
92
70
59.36
37.10
2292
2654
107
72
61.06
38.16
2357
2729
110
80
67.84
42.40
2619
3033
122
84
71.23
44.52
2750
3184
128
90
76.32
47.70
2947
3412
138
96
81.41
50.88
3143
3639
147
100
84.80
53.00
3274
3791
153
120
101.76
63.60
3929
4549
183
135
114.48
71.55
4420
5118
206
150
127.20
79.50
4911
5686
229
200
169.60
106.00
6548
7582
306
D855ST / D85ESTA~ESTH
IMAGE DIAGONAL
(INCH)
IMAGE WIDTH
(INCH)
PROJECTION DISTANCE
(MM)
IMAGE HIGHT
(INCH)
OFFSET-A
( MM )
40
32
24
536
87
60
48
36
805
130
70
56
42
939
152
72
57.6
43.2
966
156
80
64
48
1073
174
84
67.2
50.4
1127
182
90
72
54
1207
195
96
76.8
57.6
1287
208
100
80
60
1341
217
120
96
72
1609
261
135
108
81
1811
293
150
120
90
2012
326
200
160
120
2682
434
– 53 –
DLP Projector—User’s Manual
D857WT / D85GWTA~GWTE
IMAGE DIAGONAL
(INCH)
IMAGE WIDTH
(INCH)
PROJECTION DISTANCE
(MM)
IMAGE HIGHT
(INCH)
40
OFFSET-A
( MM )
Not focus
60
50.88
31.80
679
95
70
59.36
37.10
792
110
72
61.06
38.16
815
113
80
67.84
42.40
905
126
84
71.23
44.52
950
132
90
76.32
47.70
1018
142
96
81.41
50.88
1086
151
100
84.80
53.00
1131
158
120
101.76
63.60
1358
189
135
114.48
71.55
1527
213
150
127.20
79.50
1697
236
200
169.60
106.00
2263
315
D859 / D85IA~IE
IMAGE DIAGONAL
(INCH)
IMAGE WIDTH
(INCH)
PROJECTION
DISTANCE
(MM)
FROM
IMAGE HIGHT
(INCH)
PROJECTION
DISTANCE
(MM)
TO
OFFSET-A
( MM )
40
32
24
1300
1561
85
60
48
36
1951
2341
127
70
56
42
2276
2731
148
72
57.6
43.2
2341
2809
153
80
64
48
2601
3121
169
84
67.2
50.4
2731
3277
178
90
72
54
2926
3511
191
96
76.85
57.6
3121
3745
203
100
80
60
3251
3901
212
120
96
72
3901
4682
254
135
108
81
4389
5267
286
150
120
90
4877
5852
318
200
160
120
6502
7803
424
– 54 –
DLP Projector – User’s Manual
Timing Mode Table
SIGNAL
RESOLUTION
H-SYNC
(KHZ)
V-SYNC
(HZ)
COMPOSITE
/ S-VIDEO
COMPONENT
RGB
DVI/
HDMITM
NTSC
-
15.734
60.0
O
-
-
-
-
15.625
50.0
O
-
-
-
720 x 400
37.9
85.0
-
-
O
O
640 x 480
31.5
60.0
-
-
O
O
640 x 480
37.9
72.0
-
-
O
O
640 x 480
37.5
75.0
-
-
O
O
640 x 480
43.3
85.0
-
-
O
O
800 x 600
35.2
56.0
-
-
O
O
800 x 600
37.9
60.0
-
-
O
O
800 x 600
48.1
72.0
-
-
O
O
800 x 600
46.9
75.0
-
-
O
O
800 x 600
53.7
85.0
-
-
O
O
1024 x 768
48.4
60.0
-
-
O
O
1024 x 768
56.5
70.0
-
-
O
O
1024 x 768
60.0
75.0
-
-
O
O
1024 x 768
68.7
85.0
-
-
O
O
1280 x 800
49.7
59.8
-
-
O
O
1280 x 800
62.8
74.9
-
-
O
O
1280 x 800
71.6
84.8
-
-
O
O
1280 x 1024
63.98
60.0
-
-
O
O
1280 x 1024
79.98
75.0
-
-
O
O
1280 x 1024
91.10
85.0
-
-
O
O
1280 x 960
60.0
60.0
-
-
O
O
1280 x 960
85.9
85.0
-
-
O
O
1400 x 1050
65.3
60.0
-
-
O
O
1440 x 900
70.6
75.0
-
-
O
O
1440 x 900
55.6
60.0
-
-
O
O
PAL/SECAM
VESA
– 55 –
DLP Projector—User’s Manual
SIGNAL
RESOLUTION
H-SYNC
(KHZ)
V-SYNC
(HZ)
COMPOSITE
/ S-VIDEO
COMPONENT
RGB
DVI/
HDMITM
1600 x 1200
75.0
60.0
-
-
O
O
640 x 480
35.0
66.68
-
-
O
O
832 x 624
49.725
74.55
-
-
O
O
1024 x 768
60.24
75.0
-
-
O
O
1152 x 870
68.68
75.06
-
-
O
O
480i
15.734
60.0
-
O
-
O
576i
15.625
50.0
-
O
-
O
480p
31.469
60.0
-
O
-
O
576p
31.25
50.0
-
O
-
O
720p
37.5
50.0
-
O
-
O
720p
45.0
60.0
-
O
-
O
1080i
33.8
60.0
-
O
-
O
1080i
28.1
50.0
-
O
-
O
1080p
67.5
60.0
-
O
-
O
1080p
56.3
50.0
-
O
-
O
Apple Mac
SDTV
EDTV
HDTV
O: Frequency supported
—: Frequency not supported
* : Displayable level
– 56 –
DLP Projector – User’s Manual
Projector Dimensions
– 57 –
DLP Projector—User’s Manual
REGULATORY COMPLIANCE
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his/her own expense.
Changes or modifications not expressly approved by the parties responsible for compliance could
void the user’s authority to operate the equipment.
Canada
This class B digital apparatus complies with Canadian ICES-003.
Safety Certifications
FCC-B, cUL, UL, CE, C-tick, CCC, KC, CB, GOST, NOM, SASO, and Taiwan Green Mark.
– 58 –
DLP Projector – User’s Manual
APPENDIX I
RS-232C Protocol
RS232 Setting
Baud rate:
Parity
check:
Data bit:
Stop bit:
9600
None
8
1
Flow Control
None
Minimum delay for next command: 1ms
Control Command Structure
Header code
HEX
ASCII
`V’
Command code
Command
Command
Data code
Data
Data
End code
0Dh
CR
Operation Command
Note:
XX=00-98, projector's ID, XX=99 is for all projectors
Return Result P=Pass / F=Fail
n: 0:Disable/1: Enable/Value(0~9999)
ASCII
VXXS0001
VXXS0002
VXXS0003
VXXG0004
VXXS0006
Command Group 00
Function
Description
Power On
Power Off
Resync
Get Lamp Hours
System Reset
0:Reset
1:Standby
2:Operation
3:Cooling
Return Result
P/F
P/F
P/F
Pn/F
P/F
VXXG0007
Get System Status
VXXG0008
Get F/W Version
Pn/F
ASCII
VXXG0101
VXXS0101n
VXXG0102
VXXS0102n
VXXG0103
VXXS0103n
VXXG0104
VXXS0104n
VXXG0105
VXXS0105n
Command Group 01
Function
Description
Get Brightness
n=0~100
Set Brightness
n=0~100
Get Contrast
n=0~100
Set Contrast
n=0~100
Get Color
n=0~100
Set Color
n=0~100
Get Tint
n=0~100
Set Tint
n=0~100
Get Sharpness
0~31
Set Sharpness
0~31
Return Value
Pn/F
P/F
Pn/F
P/F
Pn/F
P/F
Pn/F
P/F
Pn/F
P/F
– 59 –
Pn/F
DLP Projector—User’s Manual
VXXG0106
Get Color Temperature
VXXS0106n
Set Color Temperature
VXXG0107
VXXS0107n
ASCII
VXXS0201
VXXS0202
VXXS0203
VXXS0204
VXXS0205
VXXS0206
VXXS0207
VXXG0220
ASCII
0:Cold
1:Normal
2:Warm
0:Cold
1:Normal
2:Warm
Pn/F
P/F
Get Gamma
0:PC
1:MAC
2:Video
3:Chart
4: B&W
Pn/F
Set Gamma
0:PC
1:MAC
2:Video
3:Chart
4: B&W
P/F
Command Group 02
Function
Description
Select RGB
Select RGB2
Select DVI
Select Video
Select S-Video
Select HDMI
Select BNC
Return
1:RGB
2:RGB2
3:DVI
4:Video
5:S-Video
6:HDMI
7:BNC
Get Current Source
Command Group 03
Function
Description
Return Value
P/F
P/F
P/F
P/F
P/F
P/F
P/F
Pn/F
Return Value
Get Scaling
0: Fill
1: 4:3
2: 16:9
3 :Letter Box
4 :Native
Pn/F
VXXS0301n
Set Scaling
0: Fill
1: 4:3
2: 16:9
3 :Letter Box
4 :Native
P/F
VXXG0302
VXXS0302n
VXXG0303
Blank
Blank
Auto Keystone On
VXXG0301
Pn/F
P/F
Pn/F
– 60 –
DLP Projector – User’s Manual
VXXS0303n
VXXG0304
VXXS0304n
VXXG0305
VXXS0305n
Auto Keystone On
Freeze On
Freeze On
Volume
Volume
VXXG0308
Projection Mode
n=0~8
n=0~8
0:Front
1:Rear
2:Ceiling
3:Rear+Ceiling
P/F
Pn/F
P/F
Pn/F
P/F
Pn/F
VXXS0308n
Projection Mode
0:Front
1:Rear
2:Ceiling
3:Rear+Ceiling
VXXG0309
Get vertical keystone value
n= -30~30
Pn/F
VXXS0309n
Set vertical keystone value
n= -30~30
P/F
VXXG0311
VXXS0311n
Adjust the zoom
Adjust the zoom
n=-10~10
n=-10~10
Pn/F
P/F
ASCII
VXXS0401
VXXS0402
VXXS0403
VXXS0404
VXXS0405
VXXS0406
VXXS0407
VXXS0408
VXXS0409
VXXS0410
VXXS0411
VXXS0412
VXXS0413
VXXS0414
VXXS0415
VXXS0416
VXXS0417
VXXS0418
VXXS0419
VXXS0420
Command Group 04 (Remote Control)
Function
Description
UP arrow
DOWN arrow
LEFT arrow
RIGHT arrow
POWER
EXIT
INPUT
AUTO
KEYSTONE+
KEYSTONEMENU
STATUS
MUTE
ZOOM+
ZOOMBLANK
FREEZE
VOLUME+
VOLUMEEnter
– 61 –
P/F
Return Value
P/F
P/F
P/F
P/F
P/F
P/F
P/F
P/F
P/F
P/F
P/F
P/F
P/F
P/F
P/F
P/F
P/F
P/F
P/F
P/F
2010 Vivitek Corporation. All rights reserved. All trademarks are the property of
their respective owners. All specifications are subject to change without prior notice.
201009