Axis AXIS 660 User Manual

The Axis AXIS 660 is a Token Ring network print server designed to connect printers to your network, enabling seamless printer sharing for all network users. With its support for high-speed 4 or 16 Mbps Token Ring networks, the AXIS 660 ensures efficient print data transfer. You can connect up to three different printers simultaneously to the AXIS 660, maximizing printer resource utilization and flexibility. The AXIS 660 is an ideal solution for workgroups and businesses needing a reliable and efficient way to share printers on Token Ring networks.
PDF Download
Document
1
Macintosh
UNIX
AXIS 560/660
Network Print Server
OS/2
Windows
NetWare
AXIS 560/660 User’s Manual
User’s Manual
AXIS 560/660 User’s Manual
NetWare
2
Safety Notices
Please take some time to read through the safety notices before installing the AXIS 560/660.
Caution! - must be observed to avoid loss of data or damage to your equipment.
Important: - must be observed to avoid operational impairment.
Electromagnetic Compatibility (EMC) notices - USA
This equipment generates and radiates radio frequency energy and if not installed and used in accordance with the instruction
manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A
computing device pursuant to Subpart B of Part 15 of FCC rules, which are designed to provide reasonable protection against such
interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever measures may be required to correct the
interference. Shielded cables should be used with this unit to ensure compliance with the Class A limits.
Electromagnetic Compatibility (EMC) notices - Europe
Macintosh
This digital equipment fulfils the requirements for radiated emission according to limit B of EN55022/1994, and the requirements
for immunity according to EN50082-1/1992 residential, commercial, and light industry (Compliance is not valid for unshielded
network and printer cables).
Liability
UNIX
OS/2
Windows
Do not proceed beyond any of the above notices unless you have taken appropriate measures!
Year 2000 compliance
Every care has been taken in the preparation of this manual; if you detect any inaccuracies or omissions, please inform us by
contacting your local Axis office. AXIS Communications AB cannot be held responsible for any technical or typographical errors and
reserves the right to make changes to the product and manuals without prior notice. Axis Communications AB makes no warranty of
any kind with regard to the material contained within this document, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose. Axis Communications AB shall not be liable nor responsible for incidental or
consequential damages in connection with the furnishing, performance or use of this material.
Axis Communications warrants that all versions of the AXIS 560/660, with software versions 5.48 or later, are Year 2000 compliant.
Axis’ Trademarks
NetPilot, ThinServer, ThinWizard.
Other Trademark Acknowledgments
AIX, Apple, DEC, DOS, Ethernet, EtherTalk, HP, IBM, JetAdmin, Internet Explorer, LAN Manager, LAN Server, LANtastic,
Macintosh, Microsoft, MVS, NDPS, Netscape, Novell NetWare, OS/2, OS/400, PostScript, SCO, UNIX, VM, VMS, VSE,
Windows, are registered trademarks of the respective holders.
AXIS 560/660 User’s Manual
Part No: 17162
Copyright &copy; Axis Communications AB, 1995 - 2000
Revision 3.2
Date: January 2000
About this manual
This manual provides introductory information as well as detailed instructions on how to set up
and manage the AXIS 560/660 in various network environments. It is intended for everyone
involved in installing and managing the AXIS 560/660. To fully benefit from the manual, you
should be familiar with basic networking principles.
This manual is applicable for the AXIS 560/660, with software release 6.00 or later.
Unless stated otherwise, the AXIS 560 and AXIS 660 are collectively described as the AXIS
560/660 throughout this manual.
NetWare
Thank you for purchasing the AXIS 560/660 Network Print Server. This product has been
developed to connect your printers anywhere in your network, allowing all network users access
to the shared printer resources.
Windows
Preface
3
OS/2
AXIS 560/660 User’s Manual
Axis Communications is dedicated to providing innovative solutions for network-connected
computer peripherals. Since the start in 1984, it has been one of the fastest growing companies in
the market and is now a leader in its field.
Macintosh
ThinServer™ Technology - enables Axis’ products to act as intelligent file server independent
ThinServer devices. A ThinServer device is a network server which includes “thin” embedded
server software capable of simultaneous multiprotocol communication, scalable RISC hardware
and a built-in Web server which allows easy access and management via any standard Web
browser. The ThinServer technology makes it possible to connect any electronic device to the
network, thus providing “Access to everything”.
UNIX
About Axis
Today, Axis Communications is offering six major ThinServer product lines consisting of:
Network Print Servers - offer a powerful and cost-efficient method for sharing printer resources
in your network. They connect to any standard printer, featuring high performance, simple
management and easy upgrading across the network. The print servers are available in Ethernet,
Fast Ethernet and Token Ring versions.
AXIS 560/660 User’s Manual
IBM Mainframe and S/3x - AS/400 Print Servers and Protocol Converters - include a wide
range of LAN, coax and twinax attached print servers for the IBM host environment. By
emulating IBM devices, these servers provide conversion of the IPDS, SCS and 3270DS data
streams to the major ASCII printer languages.
Network Attached CD/DVD Servers - provide a flexible and cost-efficient solution for sharing
CD-ROMs, DVD-ROMs and other optical media across the network. They are available in
Ethernet, Fast Ethernet and Token Ring versions.
Network Scan Servers - enable easy distribution of paper-based information across workgroups
and the enterprise. By sending scanned documents to your destination via the Internet/intranet,
you will reduce your faxing/mailing costs, as well as save time, thus improving your organization’s
efficiency.
Support services
UNIX
OS/2
Network Camera Servers - provide live images using standard Internet technology, thus enabling
access to live cameras via any standard Web browser. They offer a perfect solution for remote
surveillance over the Internet; their sharp images can bring life into any web site. These servers
support Ethernet as well as PSTN and GSM phone lines.
Macintosh
Windows
NetWare
4
Should you require any technical assistance, please contact your Axis dealer. If your questions
cannot be answered immediately, your Axis dealer will forward your queries through the
appropriate channels to ensure you a rapid response.
If you are connected to Internet, you can find on-line manuals, technical support, firmware
updates, application software, company information, on the addresses listed below.
WWW:
http://www.axis.com
FTP server:
ftp://ftp.axis.com/pub/axis
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The AXIS Online CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS 560 Physical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS 660 Physical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
13
14
15
17
Section 3
Basic Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting a printer to the Ethernet Network . . . . . . . . . . . . . . . . . . . .
Connecting a printer to the Token Ring Network . . . . . . . . . . . . . . . . . .
Installation Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic Setup with AXIS NetPilot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assigning an IP address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
19
20
22
24
26
30
Section 4
Setting Up - NetWare. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setup using NDPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the AXIS 560/660 in NDPS environments . . . . . . . . . . . . . . . .
Advanced Installation using AXIS NetPilot . . . . . . . . . . . . . . . . . . . . . . . .
Basic Queue-based Printing (Pure IP) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Queue-based Printing Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
43
44
45
47
51
53
Section 5
Setting Up - Windows. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS Print System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Windows 95 and Windows 98 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Windows NT4.0 and Windows 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS Print Monitor Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Windows NT 3.5x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS Print Utility for Windows Overview . . . . . . . . . . . . . . . . . . . . . . . .
Windows 3.1 and Windows for Workgroups . . . . . . . . . . . . . . . . . . . . .
Windows Clients using LANtastic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
54
56
57
62
68
69
74
76
79
Windows
Section 2
OS/2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Where to use it . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
How to use it . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Macintosh
Section 1
UNIX
Table of Contents
NetWare
5
AXIS 560/660 User’s Manual
AXIS 560/660 User’s Manual
Section 6
Setting Up - OS/2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
TCP/IP Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
NetBIOS/NetBEUI Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Section 7
Setting Up - Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Installation Using the Chooser Window . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Choosing a Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Section 8
Setting Up - UNIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation in the UNIX Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Print Methods on TCP/IP Networks . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using Logical Printers to Customize your Printing . . . . . . . . . . . . . . . . . .
Section 9
Management &amp; Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using a Web browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using AXIS ThinWizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using AXIS NetPilot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using FTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using HP Administration Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using Novell Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
108
109
115
119
127
130
133
135
138
Section 10
IPP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Address Schemes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How It Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
140
140
141
142
143
Section 11
Upgrading the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Obtaining the Updated Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Upgrading the Firmware Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
UNIX
Macintosh
OS/2
Windows
NetWare
6
92
92
95
98
Appendix C
Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Appendix D
Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
NetWare
The Parameter List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Windows
Appendix B
OS/2
Test Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Macintosh
Appendix A
7
UNIX
AXIS 560/660 User’s Manual
Section 1: Introduction
AXIS 560/660 User’s Manual
Section 1 Introduction
Based on the ThinServer technology, the AXIS 560/660 allows you to
share your available printer resources with everyone on your network.
You can connect your AXIS 560/660 directly to any standard printer.
OS/2
Windows
NetWare
8
Macintosh
The AXIS 560/660 Family of Network Print Servers
The AXIS 560/660 family currently consists of two models, which
differences are summarized in the table below.
UNIX
AXIS 560
Ethernet
AXIS 660
X
Token Ring
X
Network Speed
(Mbps)
10
4 or 16
Network Cabling
10baseT
10base2
STP
UTP
AXIS 560/660 User’s Manual
Section 1: Introduction
NetWare
Where to use it
9
Parallel
The AXIS 560/660 is the ideal print server in mixed environments as
it can communicate with all the major computer systems and network
protocols including:
•
NetWare
•
UNIX
•
Windows
•
Windows clients connected to LANtastic networks
•
OS/2
•
Macintosh (Not supported by AXIS 660)
•
Internet/intranet via any standard Web browser
UNIX
Supported
Environments
Macintosh
OS/2
Parallel
Windows
Serial
Section 1: Introduction
Installation and
Integration
OS/2
Macintosh
Notes:
UNIX
AXIS 560/660 User’s Manual
How to use it
Windows
NetWare
10
The installation of the AXIS 560/660 and its integration into the
network is performed using the appropriate Axis client software,
provided with your print server:
•
AXIS NetPilot™ (NetWare - IPX)
•
AXIS Print System (Windows 95/98, NT4.0 and 2000)
•
AXIS Print Monitor (Windows NT 3.5x)
•
AXIS Print Utility for Windows (Windows 3.1 and WfW)
•
AXIS Print Utility for OS/2
•
axinstall (UNIX)
❏ The AXIS 560 can be installed in the Macintosh environment
without any Axis client software.
❏ The AXIS 560 can be installed in NetWare - Pure IP
environments with NetWare Administrator.
Configuration and
Management
As the AXIS 560/660 comprises a built-in Web server, it can be
configured and managed directly from its internal Web pages, using
HTTP over TCP/IP. Access to the AXIS 560/660 via any javascriptenabled Web browser, offers you a platform-independent
management tool that is suitable for all supported network
environments.
In TCP/IP networks you can also use AXIS ThinWizard, which
provides you with remote management capabilities for your AXIS
ThinServer devices.
If your network does not support TCP/IP, you can use AXIS NetPilot
to configure and manage the AXIS 560/660. AXIS NetPilot supports
communication via IPX/SPX and NetBIOS/NetBEUI.
Features and Benefits
It supports printing in all the major computer systems and
environments, including five different print methods in the TCP/IP
environment. It also allows you to print on up to three printers
simultaneously.
The integrated IPP (Internet Printing Protocol) function allows for
printing from LAN to LAN via a WAN such as the Internet.
OS/2
Flexibility
Speed
The AXIS ETRAX chip has been specifically designed for LAN
products and benefits users with a faster throughput than a direct PCto-printer connection. With a sustained data throughput of up to 400
kbytes per second, the AXIS 560/660 is fast. High speed Centronics
communication such as Hewlett-Packard Fast Mode, High Speed and
IBM Fast Byte is supported.
Macintosh
The AXIS 560/660 print server provides high performance and
reliability combined with low power consumption. The electronic
circuits are based on the proven AXIS ETRAX chip, which comprises
an integrated 32 bit RISC processor and associated network
controllers.
Easy to Install
Using the available Axis installation tools, you can install the AXIS
560/660 into any of the supported networking environments in just a
few minutes.
UNIX
Reliability
11
NetWare
Section 1: Introduction
Windows
AXIS 560/660 User’s Manual
AXIS ControlPrint
(AXIS 660 only) You can add security to your available network print
resources by preventing pending print jobs to be printed until you
come to the printer. This feature prevents confidential information to
lie waiting in public. Management features allow you to keep track of
printer usage and costs.
AXIS ControlPrint requires a special version of the firmware and
additional server software. Please contact your Axis reseller for more
information.
12
Section 1: Introduction
Monitoring
OS/2
Macintosh
UNIX
You can assign passwords to restrict both login and printer access.
The provided AXIS Print System software, the AXIS NetPilot
software and the internal AXIS 560/660 Web pages allow you to
continuously monitor printer status.
The AXIS Print System and the AXIS Print Monitor can be
configured to display pop-up messages that show the status of peer-topeer print jobs.
Windows
NetWare
Security
AXIS 560/660 User’s Manual
The AXIS 560/660 additionally supports SNMP for remote
monitoring.
Futureproof
You can upgrade the AXIS 560/660 Flash memory over the network.
This allows you to quickly update and enhance the operational
features of your AXIS 560/660 when new print server software
becomes available. All software updates are free of charge.
Section 2 Product Overview
Package Contents
Verify that nothing is missing from the print server package by using
the check list below. Please contact your dealer if anything should be
missing or damaged. All packing materials are recyclable.
OS/2
AXIS 560, part no: 0053-1
AXIS 660, part no: 0054-1
13
NetWare
Section 2: Product Overview
Windows
AXIS 560/660 User’s Manual
Power Supply:
Optional accessories
Part nos.
AXIS 560 &amp;
AXIS 660
(PS-B)
Australia
13269
Europe
13267
Japan
13936
UK
13268
USA
13270
Parallel printer cable, part no: 13360
Serial printer cable, part no: 13281
UNIX
AXIS 560/660 User’s Guide, part no: 17149 rev 3.2
Macintosh
AXIS Online CD, revision 5.3 or higher
Section 2: Product Overview
Macintosh
UNIX
AXIS 560/660 User’s Manual
The AXIS Online CD
The AXIS Online CD provides an easy-to-use electronic catalog, that
includes all of the latest AXIS Utilities Software, Product Software,
White Papers, User Documentation, Technical References, etc. It is
compatible for use within all of the supported Axis computing
environments.
Start-up procedures
for Windows
The AXIS Online CD starts automatically from a local CD drive on
Windows 95/98, NT and 2000 platforms.
Windows 3.1 user’s are simply required to navigate to the CD root
directory and click on the setup31.exe file from within the Windows
File Manager.
OS/2
Windows
NetWare
14
Start-up procedures
for UNIX, OS/2
and MacOS
Note:
Using your preferred file manager application, navigate to the CD
root directory and click start.pdf.
o
If the Adobe Acrobat Reader 3.0 is not installed on to your
system, you can download it by clicking the Acrobat Reader
button located on the starting page on the AXIS Online CD.
AXIS 560/660 User’s Manual
Section 2: Product Overview
Network Connectors
Printer Ports
The AXIS 560 is designed for 10 Mbps Ethernet networks and
connects to the network via a twisted pair (10baseT) or a thin wire
(10base2) cable.
The AXIS 560 print server is provided with two high-speed IEEE
1284 compatible parallel ports and one serial port. Any standard
printer can be connected to any of the ports. Print data can be directed
to any of the three ports simultaneously, which means that three
different printers can be used at the same time, regardless of protocol.
UNIX
Plan view of the AXIS 560
Macintosh
OS/2
Windows
NetWare
AXIS 560 Physical Description
15
16
Section 2: Product Overview
UNIX
Macintosh
OS/2
Windows
NetWare
Test Button
AXIS 560/660 User’s Manual
The test button is used for:
•
•
•
Printing a test page to check the connection to the printer.
Printing the parameter list showing all the AXIS 560 settings.
Resetting the AXIS 560 parameters to the factory default settings.
Refer to Appendix A - Test Button, on page 151, for more information
about the test Button.
Network Indicator
Power Indicator
The network indicator flashes to indicate network activity.
The power indicator is lit while power is applied. If it is not lit, or it
flashes, there is a problem with the AXIS 560 or its power supply.
AXIS 560/660 User’s Manual
Section 2: Product Overview
Network Connectors
The AXIS 660 is designed for 4 and 16 Mbps Token Ring networks
and connects to the network via a shielded twisted pair (media type 1)
or unshielded twisted pair (media type 3) cable.
Printer Ports
The AXIS 660 is provided with two high-speed IEEE 1284
compatible parallel ports and one serial port. Any standard printer can
be connected to any of the ports. Print data may be directed to any of
the three ports simultaneously, which means that three different
printers can be used at the same time, regardless of protocol.
Test Button
The test button is used for:
•
Printing a test page to check the connection to the printer
•
Printing the parameter list showing all the AXIS 660 settings
•
Resetting the AXIS 660 parameters to the factory default settings.
UNIX
Plan view of the AXIS 660
Macintosh
OS/2
Windows
NetWare
AXIS 660 Physical Description
17
Windows
NetWare
18
Section 2: Product Overview
Refer to Appendix A - Test Button, on page 137, for more information
about the test button.
Ring Speed Switch
This switch is set to match your network speed.
Network Indicator
The network indicator flashes to indicate network activity.
Macintosh
OS/2
Power Indicator
UNIX
AXIS 560/660 User’s Manual
The power indicator is lit while power is applied. If it is not lit, or it
flashes, there is a problem with the AXIS 660 or its power supply.
After you have verified that no items presented in Package Contents, on
page 13, are missing, you are now ready to install your AXIS 560/660.
Follow the instructions below to install the AXIS 560/660 in your
environment:
1. Start the procedure by connecting the AXIS 560/660 to your
network and printer as described in the following table:
Print Server Model
Go to...
AXIS 560
Connecting a printer to the Ethernet Network,
on page 20
AXIS 660
Connecting a printer to the Token Ring Network, on page 22
2. When the AXIS 560/660 is successfully connected, proceed to the
Installation Guide, on page 24, where you will find further
information about how to install and integrate the AXIS 560/660
in your network environments.
NetWare
Windows
Getting Started
OS/2
Section 3 Basic Installation
19
Macintosh
Section 3: Basic Installation
UNIX
AXIS 560/660 User’s Manual
NetWare
20
Section 3: Basic Installation
Connecting a printer to the Ethernet Network
Follow the instructions below to connect a printer to the network via
the AXIS 560 print server.
Windows
Caution!
OS/2
AXIS 560/660 User’s Manual
❏ The AXIS 560 external power supply you are using must be
marked with the correct voltage! Refer to Package Contents, on
page 13.
1. Make sure that the printer is switched off and that the AXIS 560
external power supply is disconnected.
2. Locate the serial number, found on the underside label of the
AXIS 560, and write it down. You will need this number later
during the network configuration.
UNIX
Macintosh
3. Connect the printer to the LPT1, LPT2 or the COM1 port on
the AXIS 560 using an appropriate printer cable.
4. Connect your AXIS 560 to the network using a twisted pair
(10baseT) or thin wire (10base2) cable.
5. Switch on the printer and connect the external power supply to
the AXIS 560. The power indicator lights. If the network
indicator starts to flash, the AXIS 560 is successfully connected to
the network.
6. Press and release the test button on the AXIS 560 to print a test
page. If the printer and the AXIS 560 are correctly connected, the
AXIS 560 internal test page will be printed.
You are now ready to install your server onto your network using one
of the methods detailed in the Installation Guide, on page 24.
❏ The AXIS 560 uses high speed Centronics Communication. For
use with older printers not supporting high speed, this function
can be disabled by using AXIS NetPilot, or any standard Web
browser. Please refer to Section 9 Management &amp; Configuration,
on page 108, for more information.
NetWare
Windows
❏ Each AXIS 560 Print Server is pre-configured with a unique node
address that is identical to the serial number. The node address
can be changed using AXIS NetPilot, or any standard Web
browser. Please refer to Section 9 Management &amp; Configuration,
on page 108, for more information.
OS/2
❏ The test page includes a list of the most important parameters,
including the network speed and the firmware version number.
21
Macintosh
Notes:
Section 3: Basic Installation
UNIX
AXIS 560/660 User’s Manual
NetWare
22
Section 3: Basic Installation
Connecting a printer to the Token Ring Network
Follow the instructions below to connect a printer to the network via
the AXIS 660 print server.
Macintosh
OS/2
Windows
Caution!
UNIX
AXIS 560/660 User’s Manual
❏ The AXIS 660 external power supply you are using must be
marked with the correct voltage! Refer to Package Contents, on
page 13.
❏ DO NOT connect or disconnect the network cabling while AXIS
660 is powered on.
1. Make sure that the printer is switched off and that the AXIS 660
external power supply is disconnected.
2. Locate the serial number, found on the underside label of the
AXIS 660, and write it down. You will need this number later
during the network configuration.
3. Connect the printer to the LPT1, LPT2 or the COM1 port on
the AXIS 660 using an appropriate printer cable.
4. Slide the Ring Speed switch towards 4 or 16 depending on the
ring speed of your network.
5. Connect your AXIS 660 to the network using an Shielded
Twisted Pair (Media Type 1) or Unshielded Twisted Pair (Media
Type 3) cable.
6. Switch on the printer and connect the external power supply to
the AXIS 660. The power indicator lights. If the network
indicator starts to flash, the AXIS 660 is successfully connected to
the network.
7. Press and release the test button on the AXIS 660 to print a test
page. If the printer and the AXIS 660 are correctly connected, the
AXIS 660 internal test page will be printed.
You are now ready to install your server onto your network using one
of the methods detailed in the Installation Guide, on page 24.
❏ Each AXIS 660 Print Server is pre-configured with a unique node
address that is identical to the serial number. The node address
can be changed using AXIS NetPilot, or any standard Web
browser. Please refer to Section 9 Management &amp; Configuration,
on page 108, for more information.
❏ The AXIS 660 uses high speed Centronics Communication. For
use with older printers not supporting high speed, this function
can be disabled by using AXIS NetPilot, or any standard Web
browser. Please refer to Section 9 Management &amp; Configuration,
on page 108, for more information.
NetWare
Windows
❏ The test page includes a list of the most important parameters,
including the network speed and the firmware version number.
OS/2
❏ To minimize signal noise, it is recommended that you use
screened or foiled Media Type 3 cabling for 16 Mbps networks
and not standard UTP cabling.
23
Macintosh
Notes:
Section 3: Basic Installation
UNIX
AXIS 560/660 User’s Manual
NetWare
24
Section 3: Basic Installation
Installation Guide
Installation Methods
The method of installation that you choose should be dictated by your
printing requirements and your supported network environments.
Select the appropriate installation method from the table below:
Network Configuration
Windows
Environment
NDPS (Pure IP)
OS/2
Standard NetWare
(Pure IP)
Macintosh
AXIS 560/660 User’s Manual
NetWare
Action
See Assigning an IP address, on page 30
See Setup using NDPS, on page 44
See Assigning an IP address, on page 30
See Basic Queue-based Printing (Pure IP), on
page 51
NDPS (IPX)
See Setup using NDPS, on page 44
Standard NetWare (IPX)
See Basic Setup with AXIS NetPilot, on page 26
Advanced configuration
(IPX)
See Basic Setup with AXIS NetPilot, on page 26.
Proceed with Advanced Installation using AXIS
NetPilot, on page 47
TCP/IP
See Section 5 Setting Up - Windows, on page 54
NetBIOS/NetBEUI
See Section 5 Setting Up - Windows, on page 54
Windows
UNIX
See Assigning an IP address, on page 30
TCP/IP
Proceed with Section 6 Setting Up - OS/2, on
page 80
NetBIOS/NetBEUI
See Section 6 Setting Up - OS/2, on page 80
AppleTalk
See Section 7 Setting Up - Macintosh, on page 86
OS/2
Macintosh(*)
See Assigning an IP address, on page 30
UNIX
TCP/IP
*
Proceed with Section 8 Setting Up - UNIX, on
page 92
Macintosh is not supported by the AXIS 660.
Installation Tool
NetWare
TCP/IP
NetWare Administrator
IPX/SPX
AXIS NetPilot
TCP/IP
AXIS Print System
NetBIOS/NetBEUI
AXIS Print System
TCP/IP
LPR Spooler (*)
NetBIOS/NetBEUI
AXIS Print Utility for Windows
TCP/IP
Standard using the lprportd
service method
NetBIOS/NetBEUI
AXIS Print Utility for OS/2
Macintosh (**)
AppleTalk
Standard using the Chooser
UNIX
TCP/IP
axinstall
Windows
95/98/NT/2000
Windows 3.1/WfW
OS/2
Recommended installation tools for the AXIS 560/660
*
A shareware LPR spooler is available for Windows for
Workgroups. You can download this software from
ftp://ftp.axis.com/pub/axis/software/prt_srv/utility/wlprs/.
** Macintosh is not supported by the AXIS 660.
NetWare
Operating System Protocols
Windows
Environment
OS/2
The appropriate installation tools for the AXIS 560/660 are
summarized in the following table:
25
Macintosh
Installation Tools
Section 3: Basic Installation
UNIX
AXIS 560/660 User’s Manual
Windows
NetWare
26
Section 3: Basic Installation
AXIS 560/660 User’s Manual
Basic Setup with AXIS NetPilot
Follow the instructions available on the AXIS Online CD to install the
AXIS NetPilot software on to your computer. AXIS NetPilot runs on
any of the Windows platforms; Windows 3.x, Windows 95, Windows
98, Windows NT, Windows 2000 or Windows for Workgroups.
Starting the
Installation
Follow the instructions below to install the AXIS 560/660 with AXIS
NetPilot:
2. Locate the AXIS 560/660 in the ‘New Axis Units’ folder. Select it
and click the Install button on the AXIS NetPilot toolbar. If your
network is large, it could take a few seconds before the print server
appears in the folder.
3. Choose the with Installation Wizard option and click OK. The
following screen appears:
UNIX
Macintosh
OS/2
1. Start AXIS NetPilot by double-clicking the NetPilot icon, which
is located in the folder where you installed AXIS NetPilot.
The AXIS NetPilot Installation Wizard Main window
❏ The number of options varies according to the number of
environments you enable.
Print Server Name
The default print server name consists of the characters ‘AXIS’
followed by the last six digits of the serial number. If you want to
change the print server name, just type the new name in the available
text field.
Environments
Choose which networking environments you want to configure the
AXIS 560/660 for, i.e. NetWare, TCP/IP, Windows &amp; OS/2 or
Macintosh. If your network comprises various different platforms, you
can enable any combination of environments.
❏ Macintosh is not available for the AXIS 660.
NetWare NDS
Place NetWare Print Queues on a specific bindery server, or
alternatively into an NDS Tree.
The IP address
Choose the method the AXIS 560/660 should employ for obtaining
an IP address. DHCP, ARP, RARP and BOOTP are supported. You
can also select to set the IP address manually. Refer to Assigning an IP
address, on page 30 for further information about setting the IP
address.
Macintosh
Note:
UNIX
Note:
NetWare
The AXIS NetPilot Installation Wizard guides you through the
installation process. The following options are available:
27
Windows
Section 3: Basic Installation
OS/2
AXIS 560/660 User’s Manual
28
Section 3: Basic Installation
Windows
NetWare
Print Queues
AXIS 560/660 User’s Manual
The AXIS 560/660 uses the print server name followed by the printer
port as the default Print Queue name and print server port name. If
you want to change the default printer queue names, just type the new
names in the available text fields.
Environment
Default Names
NetWare
AXIS1A0003_LPT1_Q
AXIS1A0003_LPT2_Q
AXIS1A0003_COM1_Q
Windows &amp; OS/2
AX1A0003.LP1
OS/2
AX1A0003.LP2
AX1A0003.CM1
AppleTalk
AXIS1A0003_LPT1
AXIS1A0003_LPT2
Macintosh
AXIS1A0003_COM1
Default Print Queue Names and Print Server Port Names
for each of the operating environments.
UNIX
Test Page
The final user prompt in the Installation Wizard allows you to print a
test page through NetWare. The test page displays the name of all the
NetWare servers the AXIS 560/660 is connected to and shows the
status of each connection.
Unless you want to connect or create additional printing queues, the
installation for the NetWare environment is now completed.
❏ For information on advanced functions, please refer to the AXIS
Network Print Server Technical Reference. You can download
this or other technical information over the Internet by accessing
the Axis WWW Home Page at http://www.axis.com/ or the
AXIS Online CD.
NetWare
Windows
❏ No serious or permanent damage will be caused if you make a
mistake during installation. If you find, at any time, that printing
is not satisfactory, the parameters can easily be changed to tune
the system to your requirements.
OS/2
❏ The parameters entered during installation are not permanent;
they can be altered at any time according to your network
printing requirements.
29
Macintosh
Notes:
Section 3: Basic Installation
UNIX
AXIS 560/660 User’s Manual
Section 3: Basic Installation
AXIS 560/660 User’s Manual
Assigning an IP address
Before you start
System privileges
You need root privileges on your UNIX system, or administrator
privileges on a Windows NT server to set the IP address using RARP,
BOOTP or DHCP.
Ethernet address
You need to know the Ethernet address of your AXIS 560 to perform
the installation. The Ethernet address is based upon the serial number
of your AXIS 560. This means, for example, that an AXIS 560 with
the serial number of 00408C100086, will have the corresponding
Ethernet address of 00 40 8C 10 00 86. The serial number is located
on the bottom label of the unit.
Macintosh
Windows
To establish communication with the TCP/IP network, enabling
TCP/IP printing and Web browser management, an IP address must
be assigned to your AXIS 560/660.
OS/2
NetWare
30
Node address
UNIX
IP address
Important:
In Token Ring networks the node address is either the serial number
found on the underside label of the AXIS 660 or a Locally
Administrated Address
Unless you are downloading the IP address using DHCP, you must
obtain an unused IP address from your network administrator.
❏ DO NOT use the IP addresses used in the following examples
when installing your AXIS 560/660. Always consult your network
administrator before assigning an IP address to your AXIS
560/660.
See ...
AXIS IP Installer
Windows 95/98/NT/2000
page 33
DHCP
Windows NT/2000, UNIX,
NetWare 5, OS/2
page 34
Windows 95/98/NT/2000, OS/2
page 35
UNIX
page 37
RARP
UNIX
page 39
BOOTP
UNIX, NetWare 5, OS/2
page 41
AXIS NetPilot
Windows 95/98/NT/2000,
NetWare 5
Basic Setup with
AXIS NetPilot, on
page 26
ARP
Notes:
❏ The ARP and RARP methods operate on single network segments
only, that is they cannot be used over routers.
❏ Refer to Setting Parameters, on page 90 for information about
setting the IP address in the Macintosh environment.
NetWare
Network environments
Windows
Method
OS/2
You can set the IP address using one of the following methods,
depending on your network operating environment:
31
Macintosh
Methods for setting
the IP Address
Section 3: Basic Installation
UNIX
AXIS 560/660 User’s Manual
Section 3: Basic Installation
Registering and
Resolving
Host Names
In order to register the host name of the AXIS 560/660 in networks
with dynamic IP address settings, WINS (Windows Internet Name
Service) and DDNS (Dynamic Domain Naming System) are
supported. It is recommended that at least one of these methods
should be used if you are setting the IP address of the AXIS 560/660
using DHCP.
WINS host name rules
WINS only supports 15 character long host names. If your host name
is longer than 15 characters, the AXIS 560/660 truncates the host
name to 15 characters when registering with a WINS server. You can
view the AXIS 560/660 host name that is registered at a WINS server,
in the print server’s Web interface or in AXIS NetPilot. Refer to
Section 9 Management &amp; Configuration, on page 108.
DDNS host name rules
DDNS supports 53 character long host names, but they can only
consist of the characters ‘A-Z’, ’a-z’ and ‘-’. If your host name consists
of any other characters, they are converted to ‘-’, when registering with
a DDNS server. You can view the AXIS 560/660 host name that is
registered at a DDNS server, in the print server’s Web interface or in
AXIS NetPilot. Refer to Section 9 Management &amp; Configuration, on
page 108.
Macintosh
UNIX
AXIS 560/660 User’s Manual
The host name of the AXIS 560/660 is specified by the PS_NAME
parameter. Refer to B The Parameter List, on page 153
OS/2
Windows
NetWare
32
If the host name matches another entry in the DDNS data base, the
AXIS 560/660 deletes the entry before registering.
Notes:
❏ The host name limitations conclude that if you want to register
the same host name at a WINS server and a DDNS server, the
host name should be no longer than 15 characters and it should
only contain the characters ‘A - Z’, ‘a-z’ and ‘-’.
❏ Refer to your system manuals or to your network administrator
for instructions on how host name resolutions are performed on
your system.
Important!
❏ You should not use AXIS IP Installer to set the IP address of the
AXIS 560/660, if you have an active DHCP server in your
network.
1. Download the AXIS IP Installer to your host. The software is
available on the AXIS Online CD and on the Axis home page at
http://www.axis.com/.
2. Connect the AXIS 560/660 to the network. Note the serial
number that is located on the underside label of the AXIS
560/660. You will need it in the proceedings steps.
NetWare
Follow the instructions below to set the IP address of your AXIS
560/660 using the AXIS IP Installer:
33
Windows
Using
AXIS IP Installer
Section 3: Basic Installation
OS/2
AXIS 560/660 User’s Manual
5. Enter the desired IP address in the designated IP address field and
click the Set IP address button.
6. The IP setting process will take approximately 10 to 40 seconds.
Click OK in the confirmation box that appears when the IP
address has been set.
Notes:
❏ AXIS IP Installer uses the BOOTP and DHCP protocols to
communicate with the AXIS 560/660. Make sure that at least one
of these protocols is enabled in your print server.
❏ Restart your AXIS 560/660, if it does not show up in the server
list.
UNIX
4. Click the serial number of your AXIS 560/660 that appears in the
server list.
Macintosh
3. Start the AXIS IP Installer.
34
Section 3: Basic Installation
Windows
NetWare
Using DHCP
AXIS 560/660 User’s Manual
Follow the instructions below to download the IP address using
DHCP:
1. Edit or create a scope in the DHCP manager of the DHCP
daemon. The entries included in this scope should contain the
following parameters:
•
range of IP addresses
•
subnet mask
•
default router IP address
•
WINS server IP address(es) or DDNS server IP address(es)
•
lease duration
OS/2
2. Activate the scope.
The AXIS 560/660 automatically downloads the DHCP parameters.
Macintosh
If you are using WINS or DDNS, you should include at least one
WINS or DDNS server IP address in the DHCP scope. Immediately
after the IP address has been received, the AXIS 560/660 registers its
host name and IP address on the WINS alternatively DDNS server.
Refer to Registering and Resolving Host Names, on page 32 for more
information.
UNIX
The AXIS 560/660 can automatically download a customized config
file from a TFTP server. Just add the name of the config file and the
TFTP server’s IP address to your DHCP scope. The config file is
downloaded immediately after the AXIS 560/660 receives its IP
address.
Note:
❏ You do not have to restart the AXIS 560/660 to download the IP
address.
Using ARP in
Windows and OS/2
Section 3: Basic Installation
Follow the instructions below to set the IP address using ARP.
AXIS 560 Ethernet Print Servers:
1. Start a DOS window.
35
NetWare
AXIS 560/660 User’s Manual
arp -s 192.168.3.191 00-40-8c-10-00-86
ping 192.168.3.191
arp -d 192.168.3.191
The host will return Reply from 192.168.3.191 ... or a
similar message. This indicates that the address has been set and that
communication is established.
❏ When using the Windows 95 implementation of ARP, change the
first line to:
arp -s &lt;IP address&gt; &lt;Ethernet address&gt; &lt;w95host IP
address&gt;, where &lt;w95host IP address&gt; is the IP address of
your Windows 95 host.
❏ When you execute the ping command for the first time, you will
experience a significantly longer response time than is usual.
❏ By using the arp -d command, the static entry in the arp table is
removed from the host’s cache memory.
UNIX
Notes:
OS/2
Example
Macintosh
arp -s &lt;IP address&gt; &lt;Ethernet address&gt;
ping &lt;IP address&gt;
arp -d &lt;IP address&gt;
Windows
2. Type the following commands:
Section 3: Basic Installation
1. Start a DOS window.
2. Type the following commands:
Windows
arp -s 802.5 &lt;IP address&gt; &lt;Ethernet address&gt;
ping &lt;IP address&gt;
arp -d &lt;IP address&gt;
Example
arp -s 802.5 192.168.3.191 00-02-31-48-00-61
ping 192.168.3.191
arp -d 192.168.3.191
OS/2
The host will return Reply from 192.168.3.191 ... or a
similar message. This indicates that the address has been set and that
communication is established.
Notes:
Macintosh
AXIS 560/660 User’s Manual
AXIS 660 Token Ring Print Servers:
NetWare
36
❏ When using the Windows 95 implementation of ARP, change the
first line to:
arp -s &lt;IP address&gt; &lt;Ethernet address&gt; &lt;w95host IP
address&gt;, where &lt;w95host IP address&gt; is the IP address of
your Windows 95 host.
UNIX
❏ When you execute the ping command for the first time, you will
experience a significantly longer response time than is usual.
❏ By using the arp -d command, the static entry in the arp table is
removed from the host’s cache memory.
Using ARP in UNIX
Section 3: Basic Installation
Follow the instructions below to set the IP address using ARP.
AXIS 560 Ethernet Print Servers:
Type the following commands in the shell window:
37
NetWare
AXIS 560/660 User’s Manual
Notes:
❏ If the host name has not been mapped to an IP address, simply
replace the host name entry with the IP address in the example
above.
❏ The ARP command varies between different UNIX systems.
Some BSD type systems expect the host name and node address in
reverse order. Furthermore IBM AIX systems will require the
additional argument ether. For example:
arp -s ether &lt;host name&gt; 00:40:8c:10:00:86 temp
❏ When you execute the ping command for the first time, you may
experience a significantly longer response time than is usual.
OS/2
The host will return npsname is alive, or a similar message. This
indicates that the address has been set and that communication is
established.
Macintosh
arp -s npsname 00:40:8c:10:00:86 temp
ping npsname
UNIX
Example:
Windows
arp -s &lt;host name&gt; &lt;Ethernet address&gt; temp
ping &lt;host name&gt;
Section 3: Basic Installation
AXIS 560/660 User’s Manual
AXIS 660 Token Ring Print Servers:
Type the following commands in the shell window:
NetWare
38
arp -s 802.5 &lt;host name&gt; &lt;node address&gt; temp
ping &lt;host name&gt;
Windows
The node address is either the serial number found on the
underside label of the AXIS 660 or a Locally Administrated
Address.
Example:
OS/2
arp -s 802.5 npsname 00:02:31:48:00:61 temp
ping npsname
UNIX
Macintosh
The host will return npsname is alive, or a similar message. This
indicates that the address has been set and that communication is
established.
Notes:
❏ If the host name has not been mapped to an IP address, simply
replace the host name entry with the IP address in the example
above.
❏ The ARP command varies between different UNIX systems.
Some BSD type systems expect the host name and node address in
reverse order.
❏ When you execute the ping command for the first time, you may
experience a significantly longer response time than is usual.
1. Append the following line to your Ethernet Address table. This is
typically located in the /etc/ethers file:
&lt;Ethernet address&gt; &lt;host name&gt;
Example:
00:40:8c:10:00:86 npsname
2. Update, if necessary, your host table and alias name databases, as
required by your system.
3. If it is not already running, start the RARP daemon. This is
typically performed using the rarpd -a command.
NetWare
Follow the instructions below to set the IP address using RARP.
AXIS 560 Ethernet Print Servers:
39
Windows
Using RARP in UNIX
Section 3: Basic Installation
OS/2
AXIS 560/660 User’s Manual
❏ If the host name has not been mapped to an IP address, simply
replace the host name entry with the IP address in the example
above.
❏ If you are using IBM AIX, you will probably not have access to a
RARP daemon. If this is the case, you can use either the ARP or
BOOTP methods instead.
UNIX
Notes:
Macintosh
4. Restart the AXIS 560 to download the IP address.
Section 3: Basic Installation
AXIS 560/660 User’s Manual
AXIS 660 Token Ring Print Servers:
NetWare
40
1. Append the following line to your Ethernet Address table. This is
typically located in the /etc/ethers file:
Windows
&lt;Node address&gt; &lt;host name&gt;
The node address is the serial number found on the underside
label of the AXIS 660 or a Locally Administrated Address.
Example:
OS/2
00:02:31:48:00:61 npsname
2. Update, if necessary, your host table and alias name databases, as
required by your system.
Macintosh
3. If it is not already running, start the RARP daemon. This is
typically performed using the rarpd -a command.
4. Restart the AXIS 660 to download the IP address.
UNIX
Notes:
❏ If the host name has not been mapped to an IP address, simply
replace the host name entry with the IP address in the example
above.
❏ If you are a IBM AIX user, you will probably not have access to a
RARP daemon. If this is the case, you can use either the ARP or
BOOTP methods instead.
Follow the instructions below to set the IP address using BOOTP:
1. Append the following entry to your boot table. This is typically
performed by editing the file: /etc/bootptab
&lt;host name&gt;:ht=&lt;hardware type&gt;:vm=&lt;vendor magic&gt;:\
:ha=&lt;hardware address&gt;:ip=&lt;IP address&gt;:\
:sm=&lt;subnet mask&gt;:gw=&lt;gateway field&gt;
Example - AXIS 560 Ethernet Print Servers:
41
NetWare
Using BOOTP
in UNIX
Section 3: Basic Installation
Windows
AXIS 560/660 User’s Manual
Example - AXIS 660 Token Ring Print Servers:
OS/2
npsname:ht=ether:vm=rfc1048:\
:ha=00408c100086:ip=192.168.3.191:\
:sm=255.255.255.0:gw=192.168.1.1
❏ Enter the ht and vm fields exactly as shown in the example.
❏ The ha field is the Ethernet address/node address and the ip field
is the IP address of your AXIS 560/660.
❏ The gw and sm fields correspond to the default router address and
subnet mask.
❏ If the host name has not been mapped to an IP address, simply
replace the host name entry with the IP address in the example
above.
2. If necessary, update your host table and alias name databases, as
required by your system.
3. If it is not already running, start the BOOTP daemon. This is
typically performed using the bootpd command.
4. Restart the AXIS 560/660 to download the IP address, default
router address, and subnet mask.
UNIX
Notes:
Macintosh
npsname:ht=tr:vm=rfc1048:\
:ha=000231480061:ip=192.168.3.191:\
:sm=255.255.255.0:gw=192.168.1.1
UNIX
Macintosh
OS/2
Windows
NetWare
42
Section 3: Basic Installation
AXIS 560/660 User’s Manual
The AXIS 560/660 can automatically download a customized config
file from a TFTP server. Just add the name of the config file and the
TFTP server’s IP address to your boot table. The config file is
downloaded immediately after the AXIS 560/660 receives its IP
address.
Section 4: Setting Up - NetWare
Section 4 Setting Up - NetWare
This section describes how to continue the installation of the AXIS
560/660 in the NetWare environment. Identify which transport
protocol you are running on your network and which installation
method you should use. Continue the installation by selecting the
appropriate installing instructions from the table below:
Installation
method
NDPS
Queue based
printing
Transport
protocol
Action
TCP/IP
See Setup using NDPS, on page 44
IPX/SPX
Proceed with Installing the AXIS 560/660 in NDPS environments, on page 45.
IPX/SPX
If you have performed the basic installations as described in Basic Setup
with AXIS NetPilot, on page 26, the AXIS 560/660 is already installed for
printing in the NetWare environment.
IPX/SPX
Advanced
configuration
Pure IP
If you need a more advanced installation that is not covered by the AXIS
NetPilot Installation Wizard, continue with Advanced Installation using AXIS
NetPilot, on page 47.
See Basic Queue-based Printing (Pure IP), on page 51
If you intend to operate your AXIS 560/660 in a multiprotocol, mixed
environment, you should also proceed to the other relevant sections in
this manual, namely:
Section 5
Section 6
Section 7
Section 8
Setting Up - Windows, on page 54
Setting Up - OS/2, on page 80
Setting Up - Macintosh, on page 86
Setting Up - UNIX, on page 92
43
NetWare
AXIS 560/660 User’s Manual
NetWare
44
Section 4: Setting Up - NetWare
AXIS 560/660 User’s Manual
Setup using NDPS
The AXIS 560/660 supports Novell Distributed Print Services
(NDPS), which is Novell’s new generation architecture for printing
and printer administration. You can run NDPS over Pure IP
(TCP/IP) or IPX/SPX.
Before the AXIS 560/660 can be installed, make sure that NDPS and
an NDPS gateway are installed on your NetWare file server.
AXIS 560/660 uses the AXIS NDPS Gateway for printing in networks
using either IP or IPX as transport protocols. The printer gateways are
included with the NDPS software and are automatically installed
together with NDPS.
Notes:
❏ NDPS requires that you run NetWare 4.11 or higher.
❏ Pure IP is only supported by NetWare 5 or higher.
Section 4: Setting Up - NetWare
Installing the AXIS 560/660 in NDPS environments
Having assigned an IP address to the AXIS 560/660 as described in
Assigning an IP address, on page 30, you are now ready to install the
AXIS 560/660 for NDPS printing. You can select to install the
connected printers as Public or Controlled Access printers. Follow the
instructions below to install the AXIS 560/660 using NDPS:
Notes:
❏ The HP-JETADMIN parameter of the AXIS 560/660 must be set
to YES in order for the communication between the AXIS
560/660 and the NDPS gateway to be enabled.
❏ If you do not have an NDPS Manager object available, start out
with creating one in the NetWare Administrator.
Public Access
To create a public access printer using the NDPS Manager object in
your NetWare administrator, do the following:
1. Double-click on the NDPS Manager object you will be using to
control the Printer Agents.
2. At the Identification page for the NDPS Manager object you
want to use, click the Printer Agent List button. The Printer
Agent List dialog will appear.
3. Click New. The Create Printer Agent dialog will appear.
4. Type a name of your choice in the NDPS Printer Agent field.
5. Choose the Axis Gateway configuration in the Gateway Type
window. Select TCP/IP or IPX as transport protocol (See Note
below).
6. Click OK.
7. Once you have completed the required tasks, you are ready to
print in your NDPS environment.
Notes:
❏ The Public Access print servers are immediately available for
everyone on the network.
45
NetWare
AXIS 560/660 User’s Manual
Section 4: Setting Up - NetWare
AXIS 560/660 User’s Manual
❏ The Axis Gateway will appear in NetWare 5.1 and later releases.
To use the Axis Gateway with earlier versions of NetWare, you
can download the Axis Gateway Configuration utility from
www.axis.com.
NetWare
46
❏ To print using TCP/IP, Axis print server firmware 6.1 or later is
required. In order to print using IPX/SPX, Axis print server
firmware 5.51 or later is needed.
Controlled Access
1. Make sure that the NDPS Gateway is not configured to
automatically create a public access printer, before you connect
the AXIS 560/660 to the network.
2. Connect the AXIS 560/660 to the NetWare network.
3. Use the NetWare Administrator to create an NDPS printer as an
object in the NDS Tree.
4. Create a new Printer Agent (PA) or convert a Public Access
Printer to a Controlled one.
5. Choose the Axis Gateway configuration. Select TCP/IP or IPX as
transport protocol and complete required tasks.
6. You are now ready to print in your NDPS environment. Your
printer will appear as an NDS object in the Directory Tree and
will offer a full range of network security options.
Use the Novell Print Manager to install the controlled access printer
on a client workstation.
Section 4: Setting Up - NetWare
Advanced Installation using AXIS NetPilot
Having installed your AXIS 560/660 print server in accordance with
the basic installation procedures described in Basic Setup with AXIS
NetPilot, on page 26, your AXIS 560/660 print server should now
feature in the ‘Network Print Servers’ folder located in the AXIS
NetPilot main window.
NetWare Network
Environment Window
The NetWare Network Environment window allows you to connect
additional print queues to your AXIS 560/660 as well as create new
ones.
Follow the steps below to gain access to the NetWare Network
Environment window:
1. Select the required Network Print Server from the ‘Network Print
Server’ folder.
2. Choose Network from the Setup menu or click on the Network
icon on the AXIS NetPilot’s toolbar.
3. If you are not logged on to your NetWare file server, a dialog box
will ask you to log on.
47
NetWare
AXIS 560/660 User’s Manual
Section 4: Setting Up - NetWare
AXIS 560/660 User’s Manual
NetWare
48
The AXIS NetPilot NetWare Network Environment window
The AXIS 560/660 periodically updates the configuration by scanning
the NDS tree or, in the case of NetWare versions 3.x, the designated
file servers.
Connecting
Print Queues
Follow the steps below to connect a print queue to the print server
port:
1. Open the NetWare Network Environment window.
2. Select the print server port you want to connect.
3. Click the Connect... button. The Connect NetWare Print
Queues window appears.
Section 4: Setting Up - NetWare
49
NetWare
AXIS 560/660 User’s Manual
The AXIS NetPilot Connect NetWare Print Queues window
4. Select the tree or server location of the print queue from the
Resources box.
5. Select an existing print queue to connect to the server port, or
create a new print queue by clicking on Create Queue... If you
have selected an existing queue, advance to step 8. Continue with
step 6 only if you want to create a new queue.
6. Type the queue name in the Create Queue dialog window. If you
want to create a queue in the NDS tree you must also enter the
name of the volume where the queue will be located. Click OK.
7. Select the newly created queue from the queue list.
8. Select Print Server Mode or Remote Printer Mode. If you
selected Print Server Mode, advance directly to step 11, otherwise
continue with step 9. Please refer to Queue-based Printing
Methods, on page 53, for further information about the two
printing methods.
NetWare
50
Section 4: Setting Up - NetWare
AXIS 560/660 User’s Manual
9. Select an appropriate NetWare Print Server name, that will be
associated with the AXIS 560/660 print server, by using the
Browse... button.
Notes:
❏ You cannot type or edit the name manually.
❏ Make sure that you have PSERVER.NLM running if you selected
Remote Printer Mode in step 8.
10. If you want to define a remote printer number slot manually,
check the Manual box and type the desired number in the box.
11. Click the OK button to return to the Network Environments
window.
Section 4: Setting Up - NetWare
Basic Queue-based Printing (Pure IP)
Axis print servers with software version 6.0 or later allow users to print
in a Pure IP environment using traditional queue-based printing. If
you prefer using NDPS as your printing method, please refer to Setup
using NDPS, on page 44.
In the NetWare Pure IP environment, you must use the NetWare
Administrator to create the printer, print server and queue objects.
Installing the
AXIS 560/660
Follow the instructions below to install the AXIS 560/660 in the
NetWare Pure IP environment:
1. Start the Configuration Wizard from the User mode in the AXIS
560/660 Web interface.
2. Click your way through the Wizard until reaching the NetWare
page. Make sure that the PSERVER_NDS parameter is set. If you
want to change the parameter value or if the parameter value is
empty, enter the desired values. The parameter value must include
the tree or the preferred file server you want to login to and the
print server name including the context. The syntax of the
PSERVER_NDS parameter is described in PSERVER_NDS
parameter, on page 52.
3. Use NetWare Administrator to create and link the printer, print
server and queue objects in the NDS tree.
4. Use the Add Printer Wizard to install the printer on your client.
Note that only NDS queue based PSERVER printing is
supported.
Any configuration and management of the AXIS 560/660 can be
performed from any standard Web browser. Please refer to Using a Web
browser, on page 109.
In Pure IP environments, the AXIS 560/660 supports NDS queue
based PSERVER printing or NDPS printing. Refer to Queue-based
Printing Methods, on page 53 alternatively Setup using NDPS, on page
44.
51
NetWare
AXIS 560/660 User’s Manual
52
Section 4: Setting Up - NetWare
NetWare
Notes:
AXIS 560/660 User’s Manual
❏ If the PSERVER_NDS parameter includes the name of a tree and
not a specific file server, RCONAG6.NLM must be running on at
least one file server in the specified tree.
❏ If the IPX and IP transport protocols are enabled in your network,
you can use AXIS NetPilot to install the AXIS 560/660 and to
connect print queues. Please refer to Basic Setup with AXIS
NetPilot, on page 26 and Advanced Installation using AXIS
NetPilot, on page 47.
❏ Pure IP requires that you run NetWare 5 or higher.
PSERVER_NDS
parameter
As shown in the instructions in Installing the AXIS 560/660, on page
51, the PSERVER_NDS parameter specifies which NDS tree or file
server the AXIS 560/660 will login to. It also specifies the path to the
print server object in the tree. The syntax of the PSERVER_NDS
parameter is displayed in the following examples:
Example 1:
TREE:NW5_TREE DevDept.acme
In this example a print server named DevDept, with context acme,
will login to the tree, NW5_TREE.
Example 2:
171.16.2.249 DevDept.acme
In this example a print server named DevDept, with context acme,
will login to a file server with the IP address 171.16.2.249. If you have
a (D)DNS server on your network you can replace the IP address with
the host name.
Section 4: Setting Up - NetWare
53
The following overview explains the advantages and limitations of the
two supported queue-based printing methods.
NetWare
AXIS 560/660 User’s Manual
Queue-based Printing Methods
Print Server Mode
The AXIS 560/660 logs in to a file server(s) and repeatedly polls the
print queues for print jobs. In this fashion, the AXIS 560/660
emulates a NetWare print server, which is a workstation running
PSERVER. It provides high printing speed with low network load and
is the recommended mode for medium to large sized networks. Each
print server in PSERVER mode takes one NetWare user license.
Advantages
•
High performance: 150-400 kbytes/s.
Limitations
•
In bindery mode, this printing method requires a NetWare user
licence for each AXIS 560/660 to file server link.
Remote Printer Mode
The AXIS 560/660 connects to a PSERVER NetWare program
running on the file server, or to a dedicated workstation running
PSERVER.EXE. It then automatically receives print jobs from the file
server. In this fashion, the AXIS 560/660 emulates a workstation
running the NetWare remote printer software RPRINTER, or
NPRINTER. This mode is only recommended for small networks
where the number of NetWare user licences is a major issue.
Advantages
•
NetWare user licences are not required.
Limitations
•
Lower performance, typically 20 - 70 kbytes/s for NLM.
•
Higher network load.
54
Section 5: Setting Up - Windows
AXIS 560/660 User’s Manual
Windows
Section 5 Setting Up - Windows
Having connected the AXIS 560/660 to your network, as described in
Connecting a printer to the Ethernet Network, on page 20, this section
describes how to install the AXIS 560/660 in the Windows
environment. Identify your Windows platform and follow the
installing instructions from the list below.
Windows
Platform
Printing
protocol
TCP/IP
See ...
1. AXIS Print System Overview, on page 56
2. Installing TCP/IP Printers in Windows 95/98, on page 57
Windows 95,
1. AXIS Print System Overview, on page 56
Windows 98
NetBIOS/NetBEUI
TCP/IP
Windows NT 4.0,
Windows 2000
NetBIOS/NetBEUI
TCP/IP
Windows
NT 3.5x
1. AXIS Print System Overview, on page 56
2. Installing TCP/IP Printers in Windows NT 4.0/2000, on page 62
1. Installing NetBIOS/NetBEUI printers in Windows NT 4.0/2000,
on page 65
1. AXIS Print Monitor Overview, on page 68
2. Installing TCP/IP Printers in Windows NT 3.5x, on page 69
1. AXIS Print Monitor Overview, on page 68
NetBIOS/NetBEUI
Windows 3.1 &amp;
Windows for
Workgroups
2. Installing NetBIOS/NetBEUI printers in Windows 95/98, on
page 60
NetBIOS/NetBEUI
2. Installing NetBIOS/NetBEUI Printers in Windows NT 3.5x:, on
page 70
1. AXIS Print Utility for Windows Overview, on page 74
2. Windows 3.1 and Windows for Workgroups, on page 76
AXIS 560/660 User’s Manual
Section 5: Setting Up - Windows
55
If you intend to use the AXIS 560/660 in a multiprotocol
environment, you should also refer to the following sections:
Setting Up - NetWare, on page 43
Setting Up - OS/2, on page 80
Setting Up - Macintosh, on page 86
Setting Up - UNIX, on page 92
Windows
Section 4
Section 6
Section 7
Section 8
56
Section 5: Setting Up - Windows
AXIS 560/660 User’s Manual
AXIS Print System Overview
Windows
AXIS Print System is the recommended tool to use for network
printing in Windows 95, Windows 98 and Windows NT 4.0
environments. AXIS Print System allows Axis Network Print Servers
to be connected in the same simple fashion as a local printer port.
AXIS Print System has been developed for peer-to-peer printing,
allowing your print jobs to be sent directly to the AXIS 560/660.
The AXIS Print System is available in an administration version and in
a user version. The only difference between them is that the
administration version includes an IP settings application called AXIS
IP Installer.
Peer-to-Peer Printing
Client-Server Printing
The AXIS Print System needs to be installed on each workstation to
perform peer-to-peer printing. Once installed, the AXIS Print System
allows you to access all network printers, just as if they were connected
directly to your workstation. Peer-to-peer printing offers the following
benefits:
•
You can easily monitor the status of your printers
•
You do not have to rely on a server.
AXIS Print System needs only to be installed on one server to perform
client-server printing. The installed printers must be configured to be
shared to allow clients to use them. Pop-up messages should not be
enabled on the server, as they will not be displayed on the client
platforms.
AXIS 560/660 User’s Manual
Section 5: Setting Up - Windows
57
Windows 95 and Windows 98
Install the AXIS Print System software on your Windows 95 or
Windows 98 client, if you have not already done so. AXIS Print
System can be downloaded from the AXIS Online CD or from the
Axis WWW home page at http://www.axis.com/.
To enable printing in the TCP/IP environment, you must ensure that
the TCP/IP protocol is enabled on your client.
The set of instructions you should use to install TCP/IP printer ports
is dictated by the IP address of your AXIS 560/660:
Installing TCP/IP
Printer Ports and
Setting the IP Address
•
If you have an active DHCP server on the network or if you have
already set the IP address of the AXIS 560/660 using another
method, you should follow the installation instructions presented
in Installing TCP/IP Printer Ports, on page 59.
•
If your AXIS 560/660 is not assigned with a valid IP address, you
should follow the installation instructions presented in Installing
TCP/IP Printer Ports and Setting the IP Address, on page 57.
Follow the instructions below to install an AXIS Raw TCP/IP printer
port and set the IP address of the AXIS 560/660, using AXIS Print
System:
1. Start AXIS Print System by selecting AXIS Print System from the
Start menu.
2. AXIS Print System starts. Select Search for newly connected print
servers... and click Next&gt;.
3. Read the instructions and click Next&gt;.
Windows
Installing TCP/IP
Printers in
Windows 95/98
58
Section 5: Setting Up - Windows
AXIS 560/660 User’s Manual
4. AXIS IP Installer opens. Click the serial number of the AXIS
560/660 that appears in the server list. Restart the AXIS 560/660
if it does not appear in the list.
Notes:
❏ The serial number is located on the underside label of the AXIS
560/660.
Windows
❏ If you have an active DHCP server in your network, you should
not use AXIS IP Installer to set the IP address. You should instead
follow the installation instructions available in Installing TCP/IP
Printer Ports, on page 59.
5. Enter the desired IP address in the appropriate fields and click the
Set IP address button.
6. The AXIS IP Installer closes and the Installation Wizard starts.
Select the port you want to install from the list and click Next&gt;.
7. AXIS Print System searches your computer and the network for a
location for a suitable printer driver for the printer. Click Next&gt; if
a printer driver is found. If not, you have to manually find a
printer driver using the Select button before clicking the Next&gt;
button.
8. Enter a name for the printer, select if you want to make it your
default printer and select if you want to produce a test page. Click
Finish.
The printer is now installed on your computer. The printer will
feature in the My Printers window of AXIS Print System as well as in
the Printers folder of the Windows operating system.
If you want to change the default name or the password of the AXIS
560/660, use the Configuration Wizard that is available from the User
mode of the Web interface. Refer to Using a Web browser, on page
109.
Note:
❏ If you want to install LPR printer ports instead of Raw TCP/IP
printer ports, start the Microsoft Add Printer Wizard and refer to
the AXIS Print Monitor on-line help for instructions. The help
file is available in the folder where AXIS Print System is installed.
AXIS 560/660 User’s Manual
Installing TCP/IP
Printer Ports
Section 5: Setting Up - Windows
59
Follow the instructions below to install an AXIS Raw TCP/IP printer
port, using AXIS Print System:
2. AXIS Print System starts. Select your desired printer from the
Available Networks Printers window and click the Add to My
Printers button. The Add Axis Printers Wizard starts.
3. AXIS Print System searches your computer and the network for a
suitable printer driver for the printer connected to the AXIS
560/660. Click Next&gt; if a printer driver is found. If not, you have
to manually find a printer driver using the Select button before
clicking the Next&gt; button.
4. Enter a name for the printer, select if you want to make it your
default printer and select if you want to produce a test page. Click
Finish.
The printer is now installed on your computer. The printer will
feature in the My Printers window of AXIS Print System as well as in
the Printers folder of the Windows operating system.
If you want to change the default name or the password of the AXIS
560/660, use the Configuration Wizard that is available from the User
mode of the Web interface. Refer to Using a Web browser, on page
109.
Note:
❏ If you want to install LPR printer ports instead of Raw TCP/IP
printer ports, start the Microsoft Add Printer Wizard and refer to
the AXIS Print Monitor on-line help for instructions. The help
file is available in the folder where AXIS Print System is installed.
Windows
1. Start AXIS Print System by selecting AXIS Print System from the
Start menu.
60
Section 5: Setting Up - Windows
Installing
NetBIOS/NetBEUI
printers in
Windows 95/98
AXIS 560/660 User’s Manual
Follow the procedures below to install Axis NetBIOS/NetBEUI
printer ports on a Windows 95 or Windows 98 workstation, using the
AXIS Print System:
1. To start the Add Printer Wizard, select Settings - Printers from
the Start menu and double-click the Add Printer icon.
Windows
2. After clicking Next&gt; in the first dialog, the Wizard asks you to
select Local printer or Network printer. Select Local printer as the
AXIS 560/660 emulates a local printer port. Click Next&gt;.
3. Choose the appropriate printer driver for your printer. If the
desired printer driver appears in the displayed Manufacturers and
Printer Models lists, highlight your selection, click Next&gt; and
proceed directly to step 6. It is only necessary to perform steps 4 5 if your printer does not appear in the model list.
Note:
❏ Even if the desired printer is available in the Manufacturers and
Printer Models list, you are advised to use the printer driver
provided with the printer. This assures you of the latest driver
software.
4. Click the Have Disk... button. Insert the printer driver
diskette/CD that was provided with your printer, select the
appropriate diskette/CD drive and click OK.
5. Select the printer driver you want to install and click Next&gt;.
6. Select the AXIS Printer Port from the Available Ports list. The
port names appear as &lt;name&gt;.LP1, &lt;name&gt;.LP2, and
&lt;name&gt;.CM1, where &lt;name&gt; is AX followed by the last six digits
of the AXIS 560/660 serial number, e.g. AX100086. Click the
Configure Port button.
7. Choose whether error condition pop-up messages are to be
displayed by checking the box in the Configure AXIS Printer
Ports dialog. Define the frequency at which the error messages
should be displayed after retry. Click Next&gt;.
8. Enter an appropriate name for your printer and click Next&gt;.
9. Choose whether you wish to produce a test page and click Finish.
AXIS 560/660 User’s Manual
Installing Shared
Printers on your
Windows 95/98 client
Section 5: Setting Up - Windows
61
Follow the instructions below to install shared printers on your
Windows 95 or Windows 98 client:
1. Start the Add Printer Wizard by selecting Settings - Printers from
the Start menu and double-click the Add Printer icon.
3. Select Network Print Server and click Next&gt;.
4. Enter the path for the network printer or browse the network to
find and select it.
5. Choose the appropriate printer driver for your printer. If the
desired printer driver appears in the displayed Manufacturers and
Printer Models lists, highlight your selection, click Next&gt; and
proceed directly to step 8. It is only necessary to perform steps 67 if your printer does not appear in the model list.
Note:
❏ Even if the desired printer is available in the Manufacturers and
Printer Models list, you are advised to use the printer driver
provided with the printer. This assures you of the latest driver
software.
6. Click the Have Disk... button. Insert the printer driver
diskette/CD that was provided with your printer, select the
appropriate diskette/CD drive and click OK.
7. Select the printer driver you want to install and click Next&gt;.
8. Enter an appropriate name for your printer and click Next&gt;.
9. Choose whether you wish to produce a test page and click Finish.
Windows
2. Click Next&gt; in the first dialog.
62
Section 5: Setting Up - Windows
AXIS 560/660 User’s Manual
Windows NT4.0 and Windows 2000
Windows
Installing TCP/IP
Printers in Windows
NT 4.0/2000
Install the AXIS Print System software on your Windows NT 4.0
workstation, if you have not already done so. AXIS Print System can
be downloaded from the AXIS Online CD or from the Axis WWW
home page at http://www.axis.com/.
To enable printing in the TCP/IP environment, you must ensure that
the TCP/IP protocol is enabled on your client.
The set of instructions you should use to install TCP/IP printer ports
is dictated by the IP address of your AXIS 560/660:
Installing TCP/IP
Printer Ports and
Setting the IP Address
•
If you have an active DHCP server on the network or if you have
already set the IP address of the AXIS 560/660 using another
method, you should follow the installation instructions presented
in Installing TCP/IP Printer Ports, on page 64.
•
If your AXIS 560/660 is not assigned with a valid IP address, you
should follow the installation instructions presented in Installing
TCP/IP Printer Ports and Setting the IP Address, on page 62.
Follow the instructions below to install an AXIS Raw TCP/IP printer
port and set the IP address of the AXIS 560/660, using AXIS Print
System:
1. Start AXIS Print System by selecting AXIS Print System from the
Start menu.
2. AXIS Print System starts. Select Search for newly connected print
server... and click Next&gt;.
3. Read the instructions and click Next&gt;.
AXIS 560/660 User’s Manual
Section 5: Setting Up - Windows
63
4. AXIS IP Installer opens. Click the serial number of the AXIS
560/660 that appears in the server list. Restart the AXIS 560/660
if it does not appear in the list.
❏ The serial number is located on the underside label of the AXIS
560/660.
❏ If you have an active DHCP server in your network, you should
not use AXIS IP Installer to set the IP address. You should instead
follow the installation instructions available in Installing TCP/IP
Printer Ports, on page 64.
5. Enter the desired IP address in the appropriate fields and click the
Set IP address button.
6. The AXIS IP Installer closes and the Installation Wizard starts.
Select the port you want to install from the list and click Next&gt;.
7. AXIS Print System searches your computer and the network for a
location for a suitable printer driver for the printer. Click Next&gt; if
a printer driver is found. If not, you have to manually find a
printer driver using the Select button before clicking the Next&gt;
button.
8. Enter a name for the printer, select if you want to make it your
default printer and select if you want to produce a test page. Click
Finish.
The printer is now installed on your computer. The printer will
feature in the My Printers window of AXIS Print System as well as in
the Printers folder of the Windows operating system.
If you want to change the default name or the password of the AXIS
560/660, use the Configuration Wizard that is available from the User
mode of the Web interface. Refer to Using a Web browser, on page
109.
Note:
❏ If you want to install LPR printer ports instead of Raw TCP/IP
printer ports, start the Microsoft Add Printer Wizard and refer to
the AXIS Print Monitor on-line help for instructions. The help
file is available in the folder where AXIS Print System is installed.
Windows
Notes:
64
Section 5: Setting Up - Windows
Installing TCP/IP
Printer Ports
AXIS 560/660 User’s Manual
Follow the instructions below to install an AXIS Raw TCP/IP printer
port, using AXIS Print System:
1. Start AXIS Print System by selecting AXIS Print System from the
Start menu.
Windows
2. AXIS Print System starts. Select your desired printer from the
Available Networks Printers window and click the Add to My
Printers button. The Add Axis Printers Wizard starts.
3. AXIS Print System searches your computer and the network for a
suitable printer driver for the printer connected to the AXIS
560/660. Click Next&gt; if a printer driver is found. If not, you have
to manually find a printer driver using the Select button before
clicking the Next&gt; button.
4. Enter a name for the printer, select if you want to make it your
default printer and select if you want to produce a test page. Click
Finish.
The printer is now installed on your computer. The printer will
feature in the My Printers window of AXIS Print System as well as in
the Printers folder of the Windows operating system.
If you want to change the default name or the password of the AXIS
560/660, use the Configuration Wizard that is available from the User
mode of the Web interface. Refer to Using a Web browser, on page
109.
Note:
❏ If you want to install LPR printer ports instead of Raw TCP/IP
printer ports, start the Microsoft Add Printer Wizard and refer to
the AXIS Print Monitor on-line help for instructions. The help
file is available in the folder where AXIS Print System is installed.
AXIS 560/660 User’s Manual
Installing
NetBIOS/NetBEUI
printers in Windows
NT 4.0/2000
Section 5: Setting Up - Windows
65
Follow the procedure below to install Axis Printer Ports from a
Windows NT 4.0 or Windows 2000 workstation:
1. To start the Add Printer Wizard, select Settings - Printers from
the Start menu and double-click the Add Printer icon.
3. The Wizard asks you to select My Computer or Network printer
server. Select My Computer, as the AXIS 560/660 emulates a
local printer port.
4. Click Add Port... in the Available ports dialog, select AXIS Port
and click New Port...
5. Select NetBIOS/NetBEUI as your choice of network protocol
and click OK.
6. Select the AXIS Port you want to add. The ports appear as
&lt;name&gt;.LP1, &lt;name&gt;.LP2, and &lt;name&gt;.CM1, where &lt;name&gt; is
AX followed by the last six digits of the AXIS 560/660 serial
number, e.g. AX100086. Click OK.
7. Close the Printer Ports window.
8. Click the Configure Port... button. Choose whether error
condition pop-up messages are to be displayed by checking the
box in the Configure Axis Ports dialog. Define the frequency at
which the error messages should be displayed after retry. Click
OK. Continue the installation by clicking Next&gt;.
9. Choose the appropriate printer driver for your printer. Click
Next&gt; and proceed directly to step 11. It is only necessary to
perform steps 9-10 if your printer does not appear in the list.
Note:
❏ Even if the desired printer is available in the Manufacturers and
Printer Models list, you are advised to use the printer driver
provided with your printer. This assures you of the latest driver
software.
10. Click the Have Disk... button. Insert the printer driver
diskette/CD that was provided with your printer, select the
appropriate diskette/CD drive and click OK.
Windows
2. Windows 2000 only: Start the installation by clicking Next&gt;.
66
Section 5: Setting Up - Windows
AXIS 560/660 User’s Manual
11. Select the printer driver you want to install and click Next&gt;.
12. Enter an appropriate name for your printer and click Next&gt;.
Windows
13. Choose whether you want to share the printer with other network
users and click Next&gt;.
14. Choose whether you want to produce a test page and then click
Finish.
Using the Microsoft
LPD monitor with
Windows NT 4.0
This section describes how to set up a Windows NT Server v4.0 for
LPR printing over the TCP/IP protocol, using the built-in Microsoft
LPD monitor.
Basic Setup
If you have not already done so, you should perform the TCP/IP basic
setup procedures prior to installing a printer for LPD printing. These
procedures are defined in Assigning an IP address, on page 30 and
onwards.
Preparing for
LPR/LPD printing
In the Control Panel, click the Network icon. If the TCP/IP Printing
entry appears, then TCP/IP is already installed. Close the Network
folder and skip to Installing a printer on the next page.
Follow the following steps to prepare for LPR/LPD printing:
1. Open the Control Panel and click the Network icon.
2. Select Protocols.
3. Add TCP\IP Protocol.
4. Select Services.
5. Add MS TCP\IP Printing.
AXIS 560/660 User’s Manual
67
Follow the instructions below to install a printer for LPD printing:
1. Open the Control Panel and open the ‘Printers’ folder.
2. Click Add Printer, select My Computer and then go to Next.
3. Select Add Port. In Printer Ports, choose LPR Port and then click
New Port.
4. In Add LPR compatible printer, enter the host name or IP address
of the AXIS 560/660 as the print server to provide LPD.
5. Enter 'pr1', 'pr2', ... 'pr8' as the name of printer or print queue on
that server.
6. Choose a suitable printer driver for your printer and go to Next.
7. Enter a printer name and go to Next.
8. Select Shared if you want to share the printer over the network.
9. Enter a share name.
10. Click Next and then Finish.
Windows
Installing a printer
Section 5: Setting Up - Windows
68
Section 5: Setting Up - Windows
AXIS 560/660 User’s Manual
Windows
AXIS Print Monitor Overview
AXIS Print Monitor is the recommended tool to use for network
printing in Windows NT 3.5x environments. It allows AXIS Network
Print Servers to be connected in the same simple fashion as a local
printer port and once installed, is automatically initialized upon
system startup. AXIS Print Monitor has been developed for peer-topeer printing, allowing your print jobs to be sent directly to the print
server.
Printing Environments
AXIS Print Monitor supports printing over NetBIOS/NetBEUI and
TCP/IP (LPR). To enable printing in these environments, please
ensure that the desired printing protocols are running on your client.
Peer-to-Peer Printing
The AXIS Print Monitor needs to be installed on each workstation to
perform peer-to-peer printing. Once installed, the AXIS Print
Monitor allows you to access all network printers, just as if they were
connected directly to your workstation. Peer-to-peer printing offers
the following benefits:
•
You can easily monitor the status of your printers, by enabling
error condition pop-up messages.
•
You do not have to rely on a server.
Client-Server Printing
AXIS Print Monitor needs only to be installed on one server to
perform client-server printing. The installed printers must be
configured to be shared to allow clients to use them. Pop-up messages
should not be enabled on the server as they will not be displayed on
the client platforms.
Note:
❏ AXIS Print Monitor can be used for DOS printing. Please refer to
the AXIS Print Monitor’s Readme file for instructions. The
readme file is located in the same folder where AXIS Print
Monitor is installed on your PC.
AXIS 560/660 User’s Manual
Section 5: Setting Up - Windows
69
Windows NT 3.5x
Install the AXIS Print Monitor software on your Windows NT3.5x
client, if you have not already done so. AXIS Print Monitor can be
downloaded from the AXIS Online CD or from the Axis WWW
home page at http://www.axis.com/.
To be able to print using LPR, you must have installed the AXIS
560/660 in the TCP/IP environment as described in
Assigning an IP address, on page 30 and the TCP/IP protocol must be
enabled on your client.
1. Open the Print Manager and select Create Printer from the
Printer menu.
2. Enter an appropriate name in the Printer Name field.
3. Choose an appropriate printer driver for your printer from the
drop-down Driver list. If the desired printer driver already appears
in the displayed Manufacturers and Printer Models list dialog,
proceed directly to step 6. It is only necessary to perform steps 4 5 if your printer does not appear in the model list.
Note:
❏ Even if the desired printer is available in the Manufacturers and
Printer Models list, you are advised to use the printer driver
provided with your printer. This assures you of the latest driver
software.
4. Select Other... in the driver list. Insert the printer driver
diskette/CD that was provided with your printer, select the
diskette/CD drive and click OK.
5. Select the printer driver you want to install.
6. Select Other... from the “Print to” drop-down list.
7. Select AXIS Port from the list of available Print Monitors in the
Print Destination dialog. Click OK.
8. Select LPR (TCP/IP) as your choice of network protocol and
click OK.
Windows
Installing TCP/IP
Printers in
Windows NT 3.5x
70
Section 5: Setting Up - Windows
AXIS 560/660 User’s Manual
9. From the Add LPR port dialog, enter the IP address or host name
of your print server and define a Logical printer name. Click OK
to return to the Create Printer dialog.
Windows
10. Select the AXIS LPR port you wish to use from the “Print to”
drop-down list. The ports appear as &lt;port name&gt;@&lt;IP address&gt;
or &lt;port name&gt;@&lt;host name&gt;,
e.g. [email protected].
11. Click the Settings button. Choose whether error condition popup messages are to be displayed by checking the box in the
Configure AXIS LPR Ports dialog. Define the frequency at which
the error messages should be displayed after retry. Click OK to
return to the Create Printer dialog.
12. Having selected and configured the chosen port, click Next&gt;.
13. Select whether you want to share the printer with other network
users. Click OK.
The printer properties are displayed in an appropriate dialog that
allows you to refine your printer setup.
The Axis printer is now installed and will appear as an icon in the
Print Manager.
Installing
NetBIOS/NetBEUI
Printers in
Windows NT 3.5x:
Install the AXIS Print Monitor software on your Windows NT3.5x
client, if you have not already done so. AXIS Print Monitor can be
downloaded from the AXIS Online CD or from the Axis WWW
home page at http://www.axis.com/.
Follow the procedure below to install Axis printer ports from a
Windows NT 3.5x workstation:
1. Open the Print Manager and select Create Printer from the
Printer menu.
2. Enter an appropriate name in the Printer Name field.
AXIS 560/660 User’s Manual
Section 5: Setting Up - Windows
71
Note:
❏ Even if the desired printer is available in the Manufacturer and
Printer Models list, you are advised to use the printer driver
provided with your printer. This assures you of the latest driver
software.
4. Select Other... in the driver list. Insert the printer driver
diskette/CD that was provided with your printer, select the
appropriate diskette/CD drive and click OK.
5. Select the printer driver you want to install.
6. Select Other... in the “Print to” list box.
7. Select Axis Port from the list of available Print Monitors and click
OK.
8. Select the AXIS Port you wish to add and then click OK. The
ports appear as &lt;name&gt;.LP1, &lt;name&gt;.LP2, and &lt;name&gt;.CM1,
where &lt;name&gt; is AX followed by the last six digits of the AXIS
560/660 serial number, e.g. AX100086.
9. Click on Settings. Choose whether error condition pop-up
messages are to be displayed by checking the box in the Configure
Axis Ports dialog. Click OK.
10. Click OK.
Windows
3. Choose an appropriate printer driver for your printer from the
Manufacturers and Printer Models list displayed and then proceed
directly to step 6. Please note that it is only necessary to perform
steps 4 - 5 if your printer does not appear in the model list.
Section 5: Setting Up - Windows
AXIS 560/660 User’s Manual
Using the Microsoft
LPD monitor with
Window NT 3.5x
This section describes how to set up a Windows NT Server
v3.5 and v3.51 for LPD printing over the TCP/IP protocol, using the
built-in Microsoft LPD monitor.
Basic Setup
If you have not already done so, you should perform the TCP/IP basic
setup procedures prior to installing a printer for LPD printing. These
procedures are defined in Assigning an IP address, on page 30 and
onwards.
Install the TCP/IP
Protocol Stack
In the Control Panel, click the Network icon. If the TCP/IP Printing
entry appears, then TCP/IP is already installed. Close the Network
folder and continue with Installing a printer on the next page.
Windows
72
Follow these steps to install the TCP/IP protocol stack:
1. In the Control Panel, select Network.
2. Click Add Software...
3. Select “TCP/IP Protocol and related components” and then
click Continue.
4. Check “TCP/IP Network Printing Support” and then click
Continue.
5. Select path and then click Continue.
6. Click OK in the Network Settings dialog box.
AXIS 560/660 User’s Manual
73
Follow the following step-by-step instructions to install a printer for
LPD printing.
1. In the Control Panel, click the Print Manager.
2. In the Printer menu, select Create Printer.
3. In the Printer Name field, type a name for your printer.
4. Choose a suitable printer driver for your printer.
5. In the Print to field, select Other...
6. In the Print Destinations dialog, choose LPR Port and then click
OK. The Add LPR Compatible Printer dialog will now appear.
7. In the Name or Address field, type the IP address or the host
name of your AXIS 560/660. If you use a host name, this must be
defined in the hosts file on your server prior to the installation.
This file is normally located in /winnt35/system32/drivers/etc/hosts.
8. In the Name of Printer on the Machine field, type the logical
printer number you want to use, e.g. pr1. Click OK.
9. Click OK to complete the installation.
Windows
Installing a Printer
Section 5: Setting Up - Windows
74
Section 5: Setting Up - Windows
AXIS 560/660 User’s Manual
AXIS Print Utility for Windows Overview
AXIS Print Utility for Windows is the tool to use for network printing
in Windows for Workgroups and Windows 3.1 environments.
Windows
AXIS Print Utility for Windows can be downloaded from the
software\prt_srv\utility\axpuw\latest folder on the AXIS Online CD or
from the Axis WWW home page at http://www.axis.com/. Install this
utility now if you have not already done so.
About
AXIS Print Utility
for Windows
AXIS Print Utility for Windows is an application for network printing
in the Windows environment. It allows you to:
•
Install and maintain AXIS 560/660 printer ports as Windows
printer ports.
•
Capture and monitor print jobs directed to the AXIS 560/660
ports.
Print jobs are directed through a spool directory located on your local
hard disk (peer-to-peer mode), or on the file server (client-server
mode). The printer port status of your AXIS 560/660 can be
monitored and pop-up notification messages can be generated,
keeping you informed of completed print jobs or any problem
condition.
For more information about AXIS Print Utility for Windows, see the
on-line help.
Notes:
❏ Microsoft Network (NetBIOS/NetBEUI) must be running when
using AXIS Print Utility for Windows.
❏ AXIS Print Utility for Windows must be running when printing
in peer-to-peer mode.
❏ The AXIS Print Utility for Windows is not needed on the client
platforms for client-server printing.
AXIS 560/660 User’s Manual
Section 5: Setting Up - Windows
75
Peer-to-Peer vs.
Client-Server Printing
Windows for Workgroups and Windows 3.1 users, requiring access to
a network printer in peer-to-peer mode, will need to install the AXIS
Print Utility for Windows software onto their workstation. Users may
then add the required network printer to their systems and use the
printer as if it was connected directly to their workstation. Peer-topeer printing offers the following benefits:
•
You can monitor the printer status at all times and be notified
when print job are completed.
•
You do not have to rely on a server.
Client-server operation requires only one user to install the AXIS Print
Utility for Windows software onto their workstation. This user then
adds the printer to his or her workstation (the server) and shares the
printer with other users on the network. The other users (the clients)
can connect to the printer through the server via the Windows Print
Manager.
The client-server mode provides a way of maintaining queue ordering
and job priority, but at a price. This is because:
Notes:
•
You cannot receive printer status or print job notification.
•
The workstation, setup as the server, must be available at all times.
It must also have the capacity to handle the print jobs that pass
through it.
❏ When using the client-server mode, other users can still install the
AXIS Print Utility for Windows software, for printing directly to
the network printer in peer-to-peer mode.
❏ When using the client-server mode, it is recommended that the
server is setup only on a Windows for Workgroups workstation.
Windows
❏ If you want to change the default name of your AXIS 560/660 or
amend any of the default parameters, you can do so using the
AXIS NetPilot, or any standard Web browser. Refer to Section 9
Management &amp; Configuration, on page 108.
76
Section 5: Setting Up - Windows
AXIS 560/660 User’s Manual
Windows 3.1 and Windows for Workgroups
Windows
Windows 3.1
In order to print to a network printer, Windows 3.1 requires the
installation of network support, such as the LAN Server or LAN
Manager Workstation software. When installed, proceed as described
under Windows for Workgroups below.
Windows for
Workgroups
Peer-to-Peer Printing
Follow the instructions below to install your AXIS 560/660 for peerto-peer printing at a Windows for Workgroups workstation:
1. Double-click the AXIS Print Utility icon.
2. In the Port menu, click Add.
3. In the NPS Port list, select the AXIS 560/660 port. The ports
appear as &lt;name&gt;.LP1, &lt;name&gt;.LP2, and &lt;name&gt;.CM1, where
&lt;name&gt; is AX followed by the last six digits of the AXIS 560/660
serial number, e.g. AX100086.
4. Accept or change the suggested Windows port name and type any
required comment in the Description field. Make a note of the
Windows port name as you will need this later, then click OK to
install the Windows port.
5. In the Port menu, click Connect... to bring up the Windows
Printers dialog.
6. Select a printer driver from the list of Installed Printers (or click
Add&gt;&gt; to install a new driver), then click Connect...
7. Select the Windows port name from step 4 above (this name can
be found at the bottom of the Ports list).
8. Click OK to close the Connect dialog, and Close to close Printers.
The setup is completed and you can now print through your
AXIS 560/660.
AXIS 560/660 User’s Manual
❏ AXIS Print Utility for Windows must be running when you print
through your AXIS 560/660. It is strongly recommended that you
copy the AXIS Print Utility icon into your StartUp folder.
❏ To enable TCP/IP printing in Windows 3.1 and Windows for
Workgroups environments, you must use a shareware LPR
spooler that can be downloaded from
ftp://ftp.axis.com/pub/axis/software/prt_srv/utility/wlprs/.
Client-Server Printing:
Server Setup
Follow the instructions below to install your AXIS 560/660 for clientserver printing at a Windows for Workgroups server:
.
1. Choose a workstation that you want to use as a server for network
printing. The server must be available at all times and must have
sufficient hard disk space for spooling print jobs.
2. Open Network Setup, click Sharing..., check the I want to be
able to allow others to print to my printer(s) box.
3. Install AXIS Print Utility for Windows on the server.
4. Set up your AXIS 560/660 as described under Peer-to-Peer
Printing, on page 76.
5. Open Print Manager and select your printer.
6. In the Printer menu, select Share Printer As...
7. Type a printer name in the Share As field (this is the printer name
seen by the clients, see Client Setup below).
Check the Re-share at Startup box, then click OK.
The server setup is now completed.
Note:
77
❏ The AXIS Print Utility for Windows must be running when you
print through your AXIS 560/660. It is strongly recommended
that you copy the AXIS Print Utility icon into your StartUp
folder.
Windows
Notes:
Section 5: Setting Up - Windows
78
Section 5: Setting Up - Windows
Client-Server Printing:
Client Setup
AXIS 560/660 User’s Manual
Follow these steps to use your AXIS 560/660 for client-server printing
at a Windows for Workgroups client:
1. In the Control Panel, select Printers.
Windows
2. Select a printer driver from the list of Installed Printers, or click
Add&gt;&gt; to install a new driver. Click Connect...
3. Select Network... in the Device Name list, select a local port
(LPT1 - LPT3) to redirect to your network printer.
4. In the Show Shared Printers on list, select the server from Server
Setup above.
5. In the Shared Printers list, select the printer you want to use.
6. Click OK, OK and Close.
7. Exit the Control Panel.
The client setup is completed and you can now print through your
AXIS 560/660.
AXIS 560/660 User’s Manual
Section 5: Setting Up - Windows
79
Windows Clients using LANtastic
LANtastic users can use the AXIS Utilities in exactly the same manner
as described in the preceding Windows sections, using a choice of Axis
utility software that is guided by the type of Windows client
employed:
Note:
•
Refer to AXIS Print Utility for Windows Overview, on page 74, if
you are using a Windows for Workgroups client.
•
Refer to AXIS Print Monitor Overview, on page 68, if you are
using a Windows 95, Windows 98 or Windows NT client.
❏ Make sure that your LANtastic client is running the desired
printing protocols.
Windows
From any Windows client, the AXIS 560/660 can also be used for
network printing in LANtastic environments.
80
Section 6: Setting Up - OS/2
AXIS 560/660 User’s Manual
Section 6 Setting Up - OS/2
Having connected the AXIS 560/660 to your network, as described in
Connecting a printer to the Ethernet Network, on page 20, this section
now describes how to set up your AXIS 560/660 for printing in the
OS/2 environment.
OS/2
Continue with the instructions presented in the table below:
Printing
protocol
See ...
TCP/IP
TCP/IP Printing, on page 81
NetBIOS/NetBEUI
NetBIOS/NetBEUI Printing, on page 82
If you intend to operate your AXIS 560/660 in a multiprotocol
environment, you should also proceed to the other relevant sections in
this manual, namely:
Section 4
Section 5
Section 7
Section 8
Setting Up - NetWare, on page 43
Setting Up - Windows, on page 54
Setting Up - Macintosh, on page 86
Setting Up - UNIX, on page 92
AXIS 560/660 User’s Manual
Section 6: Setting Up - OS/2
81
TCP/IP Printing
Having assigned an IP address to the AXIS 560/660, as described in
Assigning an IP address, on page 30, you are now ready to install it for
TCP/IP printing in the OS/2 environment. The AXIS 560/660
supports LPR Printing using the lprportd service method.
Installing the
AXIS 560/660
Follow the instructions below to install the AXIS 560/660 using the
lprportd service method:
2. Select Printing, type a number, e.g. 3, in the Maximum number
of LPD ports field. The Remote print server and Remote print
server's printer fields should remain empty.
3. Select Autostart, select lprportd, click the Autostart check box
and select Detached.
4. Exit and Save.
5. Restart your OS/2 client.
Creating a
print queue
Continue with the instructions below to create a print queue:
1. Open the Template group. Create an new printer from
Templates by dragging the Printer icon to the desktop with the
right mouse button.
2. Select a printer driver and double-click a free Output port, for
instance \PIPE\LPD0.
3. Enter the host name or the IP address of the AXIS 560/660 in the
LPD server field.
4. Enter one of the AXIS 560/660 logical printer names, for example
pr1, in the LPD printer field.
OS/2
1. Open the OS/2 System window, select TCP/IP and TCP/IP
Configuration.
82
Section 6: Setting Up - OS/2
AXIS 560/660 User’s Manual
NetBIOS/NetBEUI Printing
The AXIS Print Utility for OS/2 is the tool to use for
NetBIOS/NetBEUI printing in OS/2 environments.
OS/2
AXIS Print Utility for OS/2 is available from the
software\prt_srv\utility\axpu\latest folder located on the AXIS Online
CD. It can also be downloaded from the Axis WWW home page at
http://www.axis.com/. Install this utility now if you have not already
done so.
If you want to change the default name or any of the AXIS 560/660
default parameters, you can do so using any standard Web browser or
AXIS NetPilot from any Windows platform that is connected to your
network, or WinOS/2 window under OS/2.
Refer to Section 9 Management &amp; Configuration, on page 108, for
more information.
The AXIS Print Utility for OS/2 is not needed on the client platforms
when using a client-server configuration.
AXIS 560/660 User’s Manual
About AXIS Print
Utility for OS/2
Section 6: Setting Up - OS/2
83
AXIS Print Utility for OS/2 is an application for NetBIOS/NetBEUI
printing in the OS/2 environment. Its allows you to:
•
Install and maintain the AXIS 560/660 printer ports as OS/2
printer ports.
•
Capture and monitor print jobs directed to the AXIS 560/660
ports.
Notes:
❏ The NetBEUI protocol must be active. If not, use MPTS/LAPS
(LAN Server) or SETUP (LAN Manager) to activate it.
❏ If you are using OS/2 version 2.x and wish to print through
TCP/IP, we recommend that you use the IBM TCP/IP for OS/2
product. It supports the LPD and interactive FTP print methods.
Installing the
AXIS 560/660
1. When AXIS Print Utility for OS/2 is running, click Install to
install your AXIS 560/660. The ports appear in the list as
&lt;name&gt;.LP1, &lt;name&gt;.LP2 and &lt;name&gt;.CM1, where &lt;name&gt; is
AX followed by the last six digits of your print server serial
number. e.g. AX100086.LP1.
2. Select the port that you want to install, then click Install.
Repeat this procedure for each server using the AXIS 560/660.
Note:
❏ The AXIS Print Utility for OS/2 must be running in order to
print through your AXIS 560/660. It is strongly recommended
that you modify the startup.cmd file, enabling AXIS Print Utility
for OS/2 to automatically start when your client is re-booted.
Instructions are available in the AXIS Print Utility for OS/2
Readme file.
OS/2
Print jobs are directed through a spool directory located on your local
hard disk (peer-to-peer mode), or on the file server (client-server
mode). The printer port status of your AXIS 560/660 can be
monitored and pop-up notification messages can be generated,
keeping you informed of completed print jobs or any problem
condition.
84
Section 6: Setting Up - OS/2
Creating
a Print Queue
(OS/2 version 2.x
and OS/2 Warp)
AXIS 560/660 User’s Manual
1. Double-click the Templates folder, then drag the Printer icon out
to the Workplace Shell (or into a folder) while holding the right
mouse button down.
2. Type a name of your choice in the Name field.
3. Select \PIPE\&lt;name&gt;.LP1, \PIPE\&lt;name&gt;.LP2 or
\PIPE\&lt;name&gt;.CM1 from the Port list, and select a printer driver
suitable for your printer from the Standard Printer list.
OS/2
4. Click OK to confirm the printer definition.
AXIS 560/660 User’s Manual
85
A print queue must be made a shared resource before it can be
accessed from other clients or servers. The following three examples
show how you can share your printer resources:
Open an OS/2 window and issue the following command:
NET SHARE &lt;queue_name&gt; /PRINT
Where &lt;queue_name&gt; is the name of the queue created on the
previous side.
To share a printer resource when using OS/2 Warp with IBM Peer
service, follow the steps below:
1. Click the right mouse button on the printer object.
2. Select Share and then Start sharing. In the dialog box, enter a
Description.
3. Select the check-box Start sharing at LAN workstation start-up.
4. Click OK.
To share a printer resource when using LAN server 4.0, follow the
steps below:
1. Open LAN Server Administration.
2. Open your domain and then Resource Definition.
3. Drag and drop a printer from the template.
4. Enter the Alias name, select a Server name and the previously
created Spooler Queue Name.
5. Click OK.
The setup is completed and you can now print through your AXIS
560/660.
OS/2
Sharing the
Print Queue
Section 6: Setting Up - OS/2
86
Section 7: Setting Up - Macintosh
AXIS 560/660 User’s Manual
Section 7 Setting Up - Macintosh
Having connected the AXIS 560 to your network, this section now
describes how to set up your AXIS 560 for printing in Macintosh
environments using AppleTalk.
If you intend to operate your AXIS 560 in a multiprotocol
environment, you should also proceed to the other relevant sections in
this manual, namely:
Section 4
Section 5
Section 6
Section 8
Macintosh
Note:
Setting Up - NetWare, on page 43
Setting Up - Windows, on page 54
Setting Up - OS/2, on page 80
Setting Up - UNIX, on page 92
❏ The AXIS 660 does not support printing in the Macintosh
environment.
Installation Using the Chooser Window
Basic Configuration
Basic configuration in AppleTalk is performed simply by opening the
Chooser window and selecting a printer.
You can change the default name of your AXIS 560 or any of default
parameters by editing the config file. To access the config file from a
Macintosh, you can use:
•
any Java enabled Web browser
•
FTP using MacTCP, Fetch or Anarchie
In order to use any of the methods, you must assign an IP address to
the AXIS 560 as described in Setting Parameters, on page 90.
AXIS 560/660 User’s Manual
Section 7: Setting Up - Macintosh
87
Choosing a Printer
LaserWriter 7.0
Printer Driver
The method for choosing a printer varies depending on which version
of LaserWriter printer driver you are using.
•
The LaserWriter 7.0 driver assumes that you use a standard PostScript driver, and cannot take advantage of any printer specific
features.
•
The LaserWriter 8.0 driver uses PPD files that contain printer
descriptions. This gives you full control over any features your
printer might have.
Follow the instructions below to choose a printer:
1. Select Chooser from the Apple menu.
2. Click the LaserWriter icon.
3. If your network has more than one zone, click on the zone you
want. If your network has no zones, this box does not appear.
4. Click the name of the printer you want. The default AXIS 560
printer names are shown as: AXIS&lt;nnnnnn&gt;_&lt;port&gt;, where
&lt;nnnnnn&gt; is the last six digits of the AXIS 560 serial number, and
&lt;port&gt; is LPT1, LPT2 and COM1 respectively. For example:
AXIS100086_LPT1.
5. Click the Close box. This completes the configuration and closes
the Chooser.
Repeat this procedure for each Macintosh computer on the network
using the AXIS 560.
Macintosh
Selecting a Printer
88
Section 7: Setting Up - Macintosh
LaserWriter 8.0
Printer Driver
AXIS 560/660 User’s Manual
Follow the instructions below to choose a printer:
1. Select Chooser from the Apple menu.
2. Click the LaserWriter 8.0 icon.
3. If your network has more than one zone click on the zone you
want. If your network has no zones, this box does not appear.
Macintosh
4. Click the name of the printer you want. The default AXIS 560
printer names are shown as: AXIS&lt;nnnnnn&gt;_&lt;port&gt;, where
&lt;nnnnnn&gt; is the last six digits of the AXIS 560 serial number, and
&lt;port&gt; is LPT1, LPT2 and COM1 respectively. For example:
AXIS100086_LPT1.
5. Click ‘Setup...’ and then ‘Auto Setup’. If the selected printer
supports bi-directional printing and the appropriate PPD file is
available, the installation is performed automatically and you can
therefore proceed directly to step 7. If this is not the case, the PPD
file must be selected manually, as described in
step 6.
6. Choose the PPD file matching your printer, and click ‘OK’.
If your printer does not appear in the PPD file list, please contact
your printer vendor. Use the Generic PPD if you do not need any
printer specific features.
7. Click ‘OK’, and then click the Close box. This completes the
configuration and closes the Chooser.
Repeat this procedure for each Macintosh computer on the network
using the AXIS 560.
AXIS 560/660 User’s Manual
Bi-directional support
Section 7: Setting Up - Macintosh
89
The AXIS 560 allows the printer driver to communicate directly with
the printer and consequently facilitates complete functional control
over print jobs, e.g. automatic downloading of fonts not resident in
the printer.
This functionality has backward compatibility with older printers and
Macintosh computers, which means that the AXIS 560 can generate
appropriate responses to Macintosh printer queries, when the
connected printer does not support bi-directional communication.
Note:
ASCII, TBCP and BCP
Note:
You simply need to print a document from the Macintosh computer
to verify communication to the chosen printer. The basic installation
can be considered complete if the print test is satisfactory. The AXIS
560 is now ready to use as a print server.
❏ For information on advanced AppleTalk functions such as nonPostScript printer support, please refer to the Axis NPS Print
Server Technical Reference on the AXIS Online CD.
The Binary Communication Protocol (BCP) and the Tagged Binary
Communication Protocol (TBCP) are communication protocols used
by the serial and parallel ports of a printer. They allow 8-bit binary
data in files concurrent with the use of some control characters, for
communication and print job control. TBCP is required for printing
with a binary data stream on some printers.
❏ Some printers, e.g. Epson InkJet printers, can not be used when
TBCP is enabled.
Macintosh
Verifying the Setup
90
Section 7: Setting Up - Macintosh
Setting Parameters
AXIS 560/660 User’s Manual
In AppleTalk, you can change a limited number of the parameters of
the AXIS 560. You can:
•
enable and disable binary data transfers for your printing
•
select the type of binary transfer protocol to use
•
specify the AppleTalk printer type
•
set the IP address
However, by assigning an IP address to your AXIS 560, you have
access to all of print server’s parameters via any standard Web browser
or via FTP. Refer to Section 9 Management &amp; Configuration, on page
108 for more information.
Macintosh
Example:
Important:
The following example describes the how you set the AXIS 560
parameters in AppleTalk.
DO NOT use the parameter values from this example when
configuring your AXIS 560. You should select values that are
appropriate for your printers and network settings.
Follow the instructions below:
1. Open the Chooser.
2. Select a network printer driver, any LaserWriter will do.
3. Select the printer port which name ends with &quot;_CFG&quot;.
4. Close the Chooser.
5. Open a text editor, e.g. SimpleText.
AXIS 560/660 User’s Manual
Section 7: Setting Up - Macintosh
91
6. Write a text file containing the parameters you want to set:
BINARY_TYPE_1.
INT_ADDR.
ATYPE_1.
:BCP
:192.168.3.191
:EPSONLQ2
Parameters that you do not want to set should be excluded from
the text file.
Refer to B - The Parameter List, on page 153, for information
about which values that are valid for each parameter.
7. Print the text file. The settings will be stored in the print server.
8. Open the Chooser and select the printer port you wish to use for
printing documents.
Note:
❏ The _CFG port disappears 60 minutes after the AXIS 560 has
been powered on. If you want it to reappear, you must restart
your AXIS 560.
Macintosh
9. Close the Chooser.
92
Section 8: Setting Up - UNIX
AXIS 560/660 User’s Manual
Section 8 Setting Up - UNIX
Installation in the UNIX Environment
Having performed the basic TCP/IP setup procedures as defined in
Assigning an IP address, on page 30 and onwards, you are now able to
print in interactive mode using LPR, FTP or Reverse Telnet protocols.
However, should you require to integrate the AXIS 560/660 into your
host spooler, you can use the Axis automatic installation script
axinstall. This utility software is resident on the AXIS 560/660 and
can be downloaded to your host using FTP, so no disks are required.
The axinstall script can also be downloaded from the Axis WWW
home page at http://www.axis.com/ and it is available on the AXIS
Online CD.
Having completed this operation, the printer connected to the AXIS
560/660 will appear as though they are directly connected to the host
printer spooler.
UNIX
If you intend to operate your AXIS 560/660 in a multiprotocol
environment, you should also proceed according to one or more of the
following sections, as appropriate to your network.
Section 4
Section 5
Section 6
Section 7
Setting Up - NetWare, on page 43
Setting Up - Windows, on page 54
Setting Up - OS/2, on page 80
Setting Up - Macintosh, on page 86
AXIS 560/660 User’s Manual
93
To integrate the AXIS 560/660 into the host printer spooler, you can
use the auto installation script axinstall, resident in the AXIS 560/660.
Follow the instructions below to install axinstall onto your host using
FTP:
1. Login to the AXIS 560/660 using the command:
ftp &lt;host name&gt; or ftp &lt;IP address&gt;
2. Enter root as the user id and pass as the password.
3. Download the script using the command:
get axinstall
Log out using the command quit, bye or exit depending on your
FTP version.
&gt; ftp npserver
connected to npserver.
220 AXIS 560/660 FTP Print Server v6.00 Jun 17 1999
ready.
Name (npsserver:thomas): root
331 User name ok, need password
Password: pass
(not visible)
230 User logged in
ftp&gt; get axinstall
200 PORT command successful.
150 Opening data connection for axinstall
(192,36,253,4,13,223), (mode ascii).
226 Transfer complete.
local: axinstall remote: axinstall
61187 bytes received in 14 seconds (4.2 kbytes/s)
ftp&gt; bye
221 Goodbye.
&gt;
Typical FTP session for collecting the axinstall script
UNIX
Integration into the
Host Printer Spooler
Section 8: Setting Up - UNIX
94
Section 8: Setting Up - UNIX
AXIS 560/660 User’s Manual
The axinstall script has now been downloaded to your host. Execute
the script with this command:
sh axinstall
You will be guided through the installation by a step-by-step
procedure. During the installation you will be asked to select a print
method; we suggest you choose LPD or, for more functionality, use
the PROS filter or named pipe methods. Please refer to the following
pages if you need guidance on the choice of print methods.
The axinstall script will suggest one of the systems listed below when
started. If you do not find the suggestion appropriate, then manually
select any of the systems listed.
1....SunOS 4 (SUN BSD, Solaris 1.x)
2....SunOS 5 (SUN SYS V, Solaris 2.x)
3....AIX (IBM RS/6000, BULL DPX 20)
4....HP-UX (HP 9000)
5....BOS (BULL DPX 2)
6....DEC OSF/1 (Digital Equipment, Alpha)
7....ULTRIX (Digital Equipment, DEC)
8....IRIX (Silicon Graphics, SGI)
9....SCO UNIX (Santa Cruz Operation)
UNIX
10...SCO UnixWare 2.x
11...SCO UnixWare 7
12...SCO OpenServer
13...FreeBSD (Berkeley UNIX)
14...Linux
15...Generic BSD (Berkeley UNIX)
16...Generic SYS V R3 (UNIX System V Release 3)
17...Generic SYS V R4 (UNIX System V Release 4)
Systems supported by axinstall
AXIS 560/660 User’s Manual
Section 8: Setting Up - UNIX
95
Print Methods on TCP/IP Networks
The AXIS 560/660 supports several different print methods in the
TCP/IP environment. axinstall will suggest a print method suitable for
your particular UNIX system, but you might want to use another
method depending on your printing requirements (banner pages,
status logging, etc).
The diagram below shows the alternative data paths taken by some of
the UNIX print methods. This illustrates some of the advantages and
limitations of the different methods. Use the following information to
determine which method to adopt.
Print
Spooler
File to
Print
Devices
Filter/
Interface
Model
Parallel Port
Directly
connected
printer
Named Pipe
DIRECT
FTP
RTELNET
LPD FTP
RTELNET PROS B
Printer
PROS print
daemon
PROS A
Axis Network Print Server
UNIX
Illustration of different UNIX print methods
LPD
The Line Printer Daemon is a protocol for transferring print jobs
between hosts. This is the recommended method for UNIX systems,
but some System V versions do not support LPD.
Advantages:
Easy to set up – install the AXIS 560/660 as a remote queue in
System V, or add a remote printer to /etc/printcap using the
rm and rp fields (BSD).
96
Section 8: Setting Up - UNIX
AXIS 560/660 User’s Manual
Limitations:
Spooler features, and printcap or lpr options (BSD) such as
multiple copies, are not available.
FTP
The File Transfer Protocol is used for transferring files between hosts.
Advantages:
Uses industry standard network software on the host.
Limitations:
No printer status logging. In the case of BSD it may conflict with
other input or output filters and does not allow both input and
output filters. In System V no filters or interface programs can be
used.
PROS
UNIX
PROS A
A protocol developed at Axis. Comes in two versions;
named pipe (PROS A) and filter (PROS B).
PROS A - Advantages:
The AXIS 560/660 appears as a device to the system. This makes
all filter and model options available. It provides accounting and
status logging. Supports bi-directional printing. The printer
information read back can be viewed in a log file.
PROS A - Limitations:
A ‘C’ compiler is required to build the PROS A drivers.
Note:
❏ You can download a ‘C’ compiler from http://www.gnu.org/.
AXIS 560/660 User’s Manual
PROS B
Section 8: Setting Up - UNIX
97
PROS B - Advantages:
It provides accounting and status logging. Supports bi-directional
printing. The printer information read back can be viewed in a
log file.
PROS B - Limitations:
A ‘C’ compiler is required to build the PROS B drivers and in the
case of BSD, it may conflict with other input or output filters. It
does not allow both input and output filters. Interface programs
can not be used in System V.
Note:
❏ You can download a ‘C’ compiler from http://www.gnu.org/.
Reverse Telnet
Often used for printing via a terminal server printer port. Only
recommended if you already have a Reverse Telnet driver installed.
Advantages:
Easy to set up with previously installed Reverse Telnet drivers.
Other UNIX Systems
Most UNIX systems resemble either BSD or System V and so with
some ingenuity, a solution can also be devised for other variants.
If the system has BSD socket type networking support, then prosbsd
(in the bsd directory of the AXIS 560/660) can be used as a starting
point. It receives print data from stdin, and writes a log file to
stderr. Nothing is written to stdout.
Alternatively, FTP may be used. It is a good idea to use bsd/ftp_bsd
or sysv/ftp_sysv as a starting point.
IBM MVS Systems
A sample JCL script, jclex, is available in the mvs directory of the
AXIS 560/660. It gives an example of how to print a file from an MVS
mainframe to an AXIS 560/660 using FTP.
UNIX
Limitations:
No status logging. Drivers are not supplied with the AXIS
560/660. Existing drivers may be slow.
98
Section 8: Setting Up - UNIX
AXIS 560/660 User’s Manual
Using Logical Printers to Customize your Printing
The AXIS 560/660 has a powerful facility for altering the print data.
This means that your desired print format can be realized on any type
of printer. The following actions can be invoked from the AXIS
560/660:
•
The character set can be changed to suit the printer
•
Strings can be added before and after the print data
•
Strings within the print data can be substituted
•
ASCII to PostScript conversion
•
Redirection of print data to another printer if the printer is busy
•
Hex Dump mode to assist with printing problems
If any of these actions are required, a Logical Printer is used to change
the print data before being sent to the printer port. There are eight
logical printers (PR1-PR8) that can be set up to filter the print data.
UNIX
The default logical printers settings are such that PR1-PR4 cause no
change to the flow of print data, while PR5-PR8 add CR to LF
control characters:
Logical Printer
Changes to data
PR1
no change
PR2
no change
PR3
no change
PR4
no change
PR5
add CR to LF
PR6
add CR to LF
PR7
add CR to LF
PR8
add CR to LF
Each logical printer can be set up using any Java enabled Web browser
or by directly editing the config file.
AXIS 560/660 User’s Manual
99
❏ The examples in this section describes how you can configure the
available logical printers using a standard Web browser. If you
want to set them directly by editing the config file, just enter the
values for the corresponding parameters.
❏ The examples should only be viewed as suggestions how to
configure the logical printers. You should, off course, configure
them according to the needs of your network.
❏ In B - The Parameter List, on page 153, you can find a complete
list of the AXIS 560/660 parameters.
❏ Refer to Section 9 Management &amp; Configuration, on page 108, for
more information about the available management tools.
UNIX
Notes:
Section 8: Setting Up - UNIX
100
Section 8: Setting Up - UNIX
Character Set
Conversion
AXIS 560/660 User’s Manual
A common problem in a multiple host environment is that different
hosts use different ASCII character sets. As a result of this, language
specific characters (such as &aring; &uuml; &ocirc; &ntilde;) are sometimes printed incorrectly.
The AXIS 560/660 solution to this problem is to assign a character set
conversion filter to a logical printer, and then link that logical printer
to the host causing the problem.
You select your desired conversion filter by setting the Character Set
Conversion (PRx_CSET) parameter. The output from the conversion
filter is always IBM PC Set 2 (Code Page 437), and this is the
character set the printer must be set up for.
Example:
Your network contains a host using the character set ISO 8859-2 and
a host using the character set DEC. In order to direct their print jobs
to the same printer, e.g. LPT1, you should assign each host to a
separate logical printer, and install a character set conversion filter.
Follow the instructions below to change the conversion filter:
1. Select the Printer1 Web page.
2. Set the parameter Physical Port to LPT1.
3. Set the parameter Character Set Conversion to ISO&gt;IBM.
UNIX
4. Click the Submit Printer1 settings button.
5. Select the Printer2 Web page.
6. Set the parameter Physical Port to LPT1.
7. Set the parameter Character Set Conversion to DEC&gt;IBM.
8. Click the Submit Printer2 settings button.
The ISO 8859-2 printer data that is sent to logical printer PR1
converts to IBM PC Set 2 and is printed on LPT1. Similarly, the DEC
printer data that is sent to logical printer PR2 converts to IBM PC Set
2 and is printed on LPT1.
AXIS 560/660 User’s Manual
Adding Strings Before
and After Print Jobs
Section 8: Setting Up - UNIX
101
These string functions provide a way to send printer control
commands before and after each print job. They may be specified
individually for each logical printer.
All strings are entered as hexadecimal byte values.
Example:
Assume that the logical printer PR5 is configured as a PostScript
printer and that you want to append the PostScript End of File
character (hex 04) after each print job.
Follow the instructions below to add a string after the print job:
1. Select the Printer5 Web page.
2. Enter the string 04 in the String After Print Job text field.
3. Click the Submit Printer5 settings button.
You have a printer with dual input bins, and want to print on preprinted forms when using the logical printer PR4. The standard forms
are taken from bin 1, and the pre-printed forms are taken from bin 2.
The string before print job should contain the command to select bin
2, ECl4H (hex 1B 26 6C 34 48), and the string after print job should
contain the command to select bin 1, ECl1H
(hex 1B 26 6C 31 48).
Follow the instructions below to add strings before and after the print
job:
1. Select the Printer4 Web page.
2. Enter the string 1B 26 6C 34 48 in the String Before Print Job
text field.
3. Enter the string 1B 26 6C 31 48 in the String After Print Job
text field.
4. Click the Submit Printer4 settings button.
UNIX
Example:
102
Section 8: Setting Up - UNIX
String Substitutions
AXIS 560/660 User’s Manual
The string substitution function performs search and replace
operations on the print data. The primary application is to replace
printer control commands. Up to twenty string substitutions may be
specified individually for each logical printer.
All strings must be entered as hexadecimal byte values, and each match
and substitute string must be preceded by a count byte.
You substitute command strings by editing the String Substitutions
(PRx_STR) parameter.
Example:
Assume that you want to replace the UNIX New Line (hex 0A) with
an ASCII NewLine (hex 0D 0A) for logical printer PR1.
Follow the instructions below to substitute command strings:
1. Select the Printer1 Web page.
UNIX
2. Enter the string 01 0A 02 0D 0A in the String Substitutions text
field.
Hex Code
Explanation
01
length of the string you want to replace
0A
the string you want to replace
02
length of the substitute string
0D 0A
the substitute string
3. Click the Submit Printer1 settings button.
This is the default setting for logical printers PR5 through PR8.
AXIS 560/660 User’s Manual
Example:
Section 8: Setting Up - UNIX
103
Assume that you want to replace the UNIX New Line (hex 0A) with
an ASCII NewLine (hex 0D 0A), and the printer command ECG1
(hex 1B 47 31) with ECY (hex 1B 59) for logical printer PR2.
Follow the instructions below to substitute command strings:
1. Select the Printer2 Web page.
2. Enter the string 01 0A 02 0D 0A 03 1B 47 31 02 1B 59 in the
String Substitutions text field.
Hex code
Explanation
01
length of the UNIX New Line command
0A
the UNIX New Line command
02
length of the ASCII New Line command
0D 0A
the ASCII New Line command
03
length of the replaced printer command
1B 47 31
the replaced printer command
02
length of the new printer command
1B 59
the new printer command
Note:
❏ Extensive use of string substitutions will naturally decrease the
throughput rate of the AXIS 560/660.
UNIX
3. Click the Submit Printer2 settings button.
104
Section 8: Setting Up - UNIX
ASCII to Postscript
Conversion
AXIS 560/660 User’s Manual
The AXIS 560/660 logical printers can translate ASCII print data into
PostScript format. This makes it possible to print with a PostScript
printer from a host that does not support PostScript. The conversion
is selected by activating a filter that converts ASCII data into
Postscript. This filter can be activated individually for each logical
printer.
Activate your desired filter by setting the Printing Language
Translation (PRx_FILT) parameter.
Example:
Follow the instructions below to convert ASCII print data to
PostScript for logical printer PR2:
1. Select the Printer2 Web page.
2. Set the Printer Language Translation parameter to POSTSCR.
3. Click the Submit Printer2 settings button.
UNIX
If you select the parameter value AUTO_PS, the print data for every
print job is searched and if any ASCII data is found, it is translated
into PostScript. This setting is recommended if you are not sure if the
print data is ASCII or PostScript.
PostScript Settings
When a logical printer is set for PostScript conversion, you must
specify the following:
•
page size
•
page orientation
•
page formats
•
which font is to be used
AXIS 560/660 User’s Manual
Section 8: Setting Up - UNIX
105
The default page size is A4 and the default page orientation is Portrait,
while the page format parameters are:
Page Format Parameter
Default Value
Lines per page
66
Characters per line
0
Characters per inch
10.0
Lines per inch
60
60 = 60 lines per inch
Left margin
30
30 = 3.0 mm
Top margin
50
50 = 5.0 mm
0=disable line wrap
The PostScript font can be any font that is installed in the printer; if
no font is specified, Courier will be used.
Follow the instructions below to set the PostScript parameters for
logical printer PR2:
1. Select the Printer2 Web page.
2. Set the Printer Language Translation parameter to POSTSCR.
3. Set the PostScript Page Size parameter to LETTER.
4. Set the PostScript Page Orientation parameter to LANDS.
5. Enter the string 48 0 120 60 30 50 in the PostScript Page
Format text field.
Hex code
Explanation
48
48 lines per page
0
disable line wrap
120
12 characters per inch
60
6 lines per inch
30
3 mm left margin
50
5 mm top margin
6. Enter the string Helvetica in the PostScript Font text field.
7. Click the Submit Printer2 settings button.
UNIX
Example:
106
Section 8: Setting Up - UNIX
AXIS 560/660 User’s Manual
Redirecting Print Jobs
when a printer is busy
If print data is received for a printer that is already busy, the host must
wait. However, it is possible to use a logical printer to redirect the
print data to another logical printer when the target printer is busy. If
the second printer is also busy, the host must wait until the target
printer is ready.
Example:
Follow the instructions below to redirect PR1 print jobs to PR3, when
the printer assigned to PR1 is busy:
1. Select the Printer1 Web page.
2. Set the Physical Port parameter to LPT1.
3. Set the Secondary Printer parameter to PR3.
4. Set the Wait On Busy parameter to NO.
5. Click the Submit Printer1 settings button.
6. Select the Printer3 Web page.
7. Set the Physical Port parameter to LPT2.
8. Click the Submit Printer3 settings button.
UNIX
Notes:
❏ Logical Printer redirection cannot be nested. If PR3 is redirected
to another logical printer, the print job will not be redirected if
PR3 is busy.
❏ If both printers are busy, the print job will be printed on the
printer that first finishes its active print job.
AXIS 560/660 User’s Manual
Read-back of
information
Section 8: Setting Up - UNIX
107
The AXIS 560/660 supports bi-directional printing. The information
from the printer is read back on the parallel port when the parameter
Read Back Port (PRx_IN) has the default setting of AUTO. However,
it is required that the printer also supports bi-directional printing.
Please refer to your printer documentation for further details regarding
bi-directional printing support.
Example:
Follow the instructions below to disable the bi-directional
communication for logical printer PR1:
1. Select the Printer1 Web page.
2. Set the Read Back Port parameter to NONE.
3. Click the Submit Printer1 settings button.
Example:
When hex dump mode is activated, the print data is printed as
hexadecimal byte values rather than characters; printer control
commands are also printed as hex values. This allows you to inspect
what control and print characters are being sent to the printer, which
is a useful debugging facility for the more difficult printing problems.
Follow the instructions below to activate the hex dump mode for PR3:
1. Select the Printer3 Web page.
2. Set the Hex Dump Mode Enabled radio button to YES.
3. Click the Submit Printer3 settings button.
Note:
❏ The page length for hex dump printouts is determined by the
lines per page value of the PostScript page format parameter.
UNIX
Debugging using the
Hex Dump Mode
Section 9: Management &amp; Configuration
The management and configuration tools that are supported by the
AXIS 560/660 allows you to:
OS/2
Macintosh
Configuration
Overview
UNIX
AXIS 560/660 User’s Manual
Section 9 Management &amp; Configuration
Windows
NetWare
108
•
Change the print server parameters, i.e. editing the config file
•
Receive extended information about the print jobs
•
Receive printer port status
•
Monitor your printers
•
Reset the AXIS 560/660
•
Upgrade the AXIS 560/660 firmware (Refer to Section 11
Upgrading the Software, on page 147)
The method you should use to manage and configure your AXIS
560/660 is depending on the operating system protocols of your
network. The table below displays which method to use for each
supported environment.
Operating System Protocols
Configuration/Management methods
IPX/SPX
(NetWare)
•
AXIS NetPilot - See page 119
•
HP JetAdmin - See page 135
•
Novell Utilities - See page 138
•
Web Browser - See page 109
•
AXIS ThinWizard - See page 115
•
FTP - See page 127
•
telnet - See page 130
•
SNMP - See page 133
•
HP Web JetAdmin - See page 135
NetBIOS/NetBEUI
(Windows 95/98/NT/2000,
Windows 3.1/WfW, OS/2)
•
AXIS NetPilot - See page 119
AppleTalk
•
Web browser - See page 109
•
Mac-FTP - See page 127
•
AXIS NetPilot via a PC platform in the
same network - See page 119
TCP/IP
(UNIX,
Windows 95/98/NT/2000,
Windows 3.1/WfW,
NetWare Pure IP, OS/2)
The Web interface of the AXIS 560/660 is divided into two modes of
operation, User mode and Admin mode.
User
In User mode, you have no rights to change any parameter settings.
However, if you have access rights to the Admin mode, you can
change some of the basic parameters from User mode via the
Configuration Wizard. This mode is intended for regular users who
are only interested in using the print server's interface for checking
print jobs or viewing printer properties. If you want to change any
other of the print server's settings, you must enter the Admin mode.
Admin
When in Admin mode, you have access to all the print server's
parameters and you can change them to your liking. This mode is
intended for network administrators and is password protected to
prevent unauthorized changing of the print server parameters.
Note:
❏ If the ROOT_PWD parameter is set to pass, which is the default
value, you have access to the User mode as well as the Admin
mode.
Accessing the
Web Pages
Follow the steps below to access the internal home page of the AXIS
560/660. The browser used in the following example is Netscape
Navigator 4.3.
1. Start your Web browser.
2. From the File menu, select Open Page...
NetWare
Windows
Once you have established the AXIS 560/660 in the TCP/IP
environment, as described in Assigning an IP address on page 30, you
are free to access the AXIS 560/660 Web pages from any Java enabled
Web browser.
OS/2
Using a Web browser
109
Macintosh
Section 9: Management &amp; Configuration
UNIX
AXIS 560/660 User’s Manual
Section 9: Management &amp; Configuration
AXIS 560/660 User’s Manual
3. Type the host name or the IP address of your AXIS 560/660 in
the Open Page dialog, as detailed below:
OS/2
Windows
NetWare
110
The User Mode home page of your AXIS 560/660 appears in the
browser window.
UNIX
Macintosh
You can alternatively type the host name or the IP address directly
into the Web browser’s Location text field.
The AXIS 560/660 User Home Page
Section 9: Management &amp; Configuration
Available Services
from the User Mode
The following services are available from the User mode. An
additional link to the Axis home page is available from this mode.
The Printer Overview page contains a section that allows you to view
the general parameter setting of the AXIS 560/660, including the
print server name and the location of the print server in your
organization, if defined.
If you have admin access rights you can use the Configuration Wizard
to perform basic configuration of the AXIS 560/660.
UNIX
The AXIS 560/660 Administrator Home Page
Macintosh
OS/2
Windows
Click the Admin button to enter the Admin mode. If the management
password is set to anything but pass, you must enter root as the user
and the password. The password pass is the default password of the
AXIS 560/660.
111
NetWare
AXIS 560/660 User’s Manual
Section 9: Management &amp; Configuration
AXIS 560/660 User’s Manual
By clicking on the printer icons, a printer page opens, allowing you to
view the status and the supported capabilities of each connected
printer. The extent of this information is depending on the printer
model. From the printer page, you can also print a test page to the
selected printer.
Windows
NetWare
112
OS/2
From the Print Jobs page you can view the status of the current print
jobs, including the number of printed bytes and the origin of the print
job. You can also view a log of the 20 latest print jobs that includes the
user, the printing protocol and the file size. A log that displays the
accumulated usage of the connected printers allows you to control the
usage of the connected printers.
Macintosh
The General Help page presents you with basic information about the
AXIS 560/660 and the Web user interface. A short description of the
Axis installation tools, you should use when installing a printer on
your PC, is also included.
UNIX
Available Services
from the Admin Mode
The following services are available from the Admin mode. An
additional link to the Axis home page is available from this mode
The This Print Server page contains a section that allows you to view
and modify the general parameter setting of the AXIS 560/660,
including the print server name, the node address, the password and
the base URL. You can also configure any of the eight available logical
printers of the AXIS 560/660. Management operations, like restarting
the AXIS 560/660 and resetting its parameters to the factory default
settings, are also available.
From the Network Settings page you can set all parameters that
control the network traffic to and from the AXIS 560/660. You can
enable or disable any of the supported network protocols and finetune the parameter settings.
Caution!
❏ Any network configuration should involve the Network
Administrator.
From the Support page you can receive help to resolve any installation
or print problems that might occur. If your problems persist, the
Support page allows you to produce a Server Report. The Server
Report includes the settings of the AXIS 560/660, information about
your connected printers as well as the current network settings. The
Server Report is of great value for support assistance, so please mail,
email or fax it to your support channel together with a detailed
problem description.
The Statistics page displays information about the network traffic to
and from the AXIS 560/660 as well as information about servers and
services that are connected or associated with the AXIS 560/660.
NetWare
Windows
From the Print Jobs page you can view the status of the current print
jobs, including the number of printed bytes and the origin of the print
job. You can also view a log of the 20 latest print jobs that includes the
user, the printing protocol and the file size. A log that displays the
accumulated usage of the connected printers allows you to control the
usage of the connected printers. If you want to delete an ongoing print
job, a delete button is available on this page.
OS/2
By clicking on the printer icons, a printer page opens, allowing you to
view the status and the supported capabilities of each connected
printer. The extent of this information is depending on the printer
model. From the printer page, you can also print a test page to the
selected printer.
113
Macintosh
Section 9: Management &amp; Configuration
UNIX
AXIS 560/660 User’s Manual
UNIX
Macintosh
OS/2
Windows
NetWare
114
Section 9: Management &amp; Configuration
AXIS 560/660 User’s Manual
The Help Contents displays a comprehensive description of the
configuration and management activities that can be performed from
the internal Web pages of the AXIS 560/660. Theses activities include
instructions on how to install the AXIS 560/660 in various
environments and how to upgrade it with new firmware. A detailed
index is also available.
The internal Web pages of Axis ThinServer products integrate directly
into AXIS ThinWizard, giving you access to the services described in
Using a Web browser on page 109.
Once you have established the AXIS 560/660 in the TCP/IP
environment, as described in Assigning an IP address on page 30, you
are free to access the AXIS 560/660 from AXIS ThinWizard.
Installing AXIS
ThinWizard
You should only install AXIS ThinWizard on a designated server on
your network. When you want to use the AXIS ThinWizard for
management purposes, you just access the server via any standard Web
browser.
The AXIS ThinWizard software is available on the AXIS Online CD
and can also be downloaded from the Axis WWW home page at
http://www.axis.com/.
Note:
❏ You cannot install the AXIS ThinWizard server software on a
Windows 3.1 or a Windows for Workgroups server. However,
you can access AXIS ThinWizard’s Web interface from any
TCP/IP client in your network
NetWare
Windows
AXIS ThinWizard is a management tool that allows you to manage
and upgrade ThinServer products. You can find, monitor and upgrade
your Axis print servers remotely in any TCP/IP network using a
standard Web browser.
OS/2
Using AXIS ThinWizard
115
Macintosh
Section 9: Management &amp; Configuration
UNIX
AXIS 560/660 User’s Manual
Section 9: Management &amp; Configuration
Starting AXIS
ThinWizard
AXIS 560/660 User’s Manual
Follow the instructions below to start the AXIS ThinWizard:
1. Make sure that the computer where you installed the AXIS
ThinWizard is up and running on your network.
2. Start a Web browser from a client in your network.
3. Enter the IP address or the host name of the server where you
installed AXIS ThinWizard. If the server is installed on another
port than 80, you must enter the port name after the host name or
the IP address.
UNIX
Macintosh
OS/2
Windows
NetWare
116
4. The AXIS ThinWizard start page appears in the Web browser.
Enter your user name and the password and click the Log in
button.
5. The AXIS ThinWizard interface appears. Select a network group
from the list. If the list is empty, you must first create a group.
The network group concept is the corner stone of AXIS ThinWizard.
By dividing your network into network groups, you can monitor your
print servers more efficiently. The scope of each network group is
determined by the Axis server types and IP address ranges that are
included. You can create as many network groups as you want.
117
2. Click the Create button.
3. The Create Network Group page opens. Type the name of the
network group, identify the IP address ranges and Axis server
types that should be included. If you are only interested in
managing print servers, deselect all options but the Print Servers
option.
OS/2
1. Click the Network Groups button in the AXIS ThinWizard main
menu.
Windows
Follow the instructions below to create a network group:
You can edit the properties of each network group from the Network
Groups page. Simply select the network group from the list and use
one of the Edit, Copy or Remove commands.
Macintosh
4. Click OK to create the network group.
UNIX
Creating a
Network Group
Section 9: Management &amp; Configuration
NetWare
AXIS 560/660 User’s Manual
Section 9: Management &amp; Configuration
Managing the
print servers
AXIS 560/660 User’s Manual
Follow the instructions below to access the AXIS 560/660 using AXIS
ThinWizard:
1. Click the Manage Network button in the main menu.
2. Select the network group, including the AXIS 560/660, from the
drop-down list. All AXIS servers included in the network group
appear in the window.
Windows
NetWare
118
3. Click the link of the AXIS 560/660 to access its internal Web
page.
UNIX
Macintosh
OS/2
4. The ‘Srv’ and ‘Dev’ columns show the status of your print servers
and printers.
You are now free to manage and configure the AXIS 560/660 as
described in Available Services from the User Mode on page 111.
Upgrading
Axis Servers
Refer to Upgrading using AXIS ThinWizard on page 148, for more
information about upgrading Axis Servers using AXIS ThinWizard.
Additional
Information
If you need more information, please refer to the AXIS ThinWizard
on-line help.
Section 9: Management &amp; Configuration
Using AXIS NetPilot
AXIS NetPilot is the recommended tool to use for configuring the
AXIS 560/660 in networks that support communication via the
IPX/SPX or the NetBIOS/NetBEUI protocols.
119
NetWare
AXIS 560/660 User’s Manual
•
Modify network environment settings
•
Monitor your printers on the network
•
Create logical groups of print servers to simplify administration
•
Upgrade the AXIS 560/660
OS/2
Change the AXIS 560/660 parameter values
Macintosh
Start AXIS NetPilot by clicking the AXIS NetPilot icon, which resides
in the folder where you installed AXIS NetPilot.
UNIX
Starting AXIS
NetPilot
•
Windows
AXIS NetPilot allows you to:
The main window of AXIS NetPilot
Section 9: Management &amp; Configuration
Changing the
parameter values
OS/2
The Property Pages
AXIS 560/660 User’s Manual
AXIS NetPilot provides you with two useful tools for changing
parameter values:
•
Property pages:
•
Parameter List Editor: Use this fast and efficient tool if you have
considerable experience in editing config
files.
Windows
NetWare
120
Use the Property pages if you have little
experience in editing config files and need
a user-friendly interface.
The Property pages provide an easy way to view and change the
parameters. Each property page comprises a set of selection tabs that
are appropriate to your operating environments. Each parameter can
be edited by selecting the relevant box.
Follow the instructions below to open and edit an arbitrary Property
Page:
Macintosh
1. Select the AXIS 560/660 from the ‘Network Print Servers’ folder.
2. Click the Properties button on the AXIS NetPilot toolbar or
choose Properties from the Setup menu.
3. Select the tab that includes the parameter you want to change.
UNIX
4. Change the value.
5. Click Apply to save the change to the print server. (If you select
OK instead, the Property pages closes automatically after the
change has been saved).
The Parameter
List Editor
The Parameter List Editor is a simple editor that enables you to:
•
Edit the AXIS 560/660 config file.
•
Save customized config files to your hard disk.
•
configure several network print servers simultaneously.
Section 9: Management &amp; Configuration
Follow the instructions below to use the Parameter List Editor:
1. Choose Edit Parameter List from the Setup menu.
2. Download a config file from a print server or from your hard disk
by selecting from File or from Print Server.
121
NetWare
AXIS 560/660 User’s Manual
6. Click Save after you have made your choice, to save the modified
config file.
Modifying the
network
environments
❏ When saving the config file to multiple print servers, make sure
that you do not assign the same IP address to different print
servers.
From the Network Environment window you can modify the network
settings for each supported network environment.
To gain access to the Network Environment window, follow the
instructions below:
1. Select the AXIS 560/660 from the ‘Network Print Servers’ folder.
2. Click on the Network button on the toolbar or select Network
from the Setup menu.
3. Select the tab corresponding to the environment that you want to
modify.
UNIX
Important:
OS/2
5. Select the appropriate radio button, To File or To Print Server.
Macintosh
4. Edit the config file.
Windows
3. Click the Load button and the config file opens in the editor.
122
Section 9: Management &amp; Configuration
To simplify printer monitoring, you can create logical groups of
printers. The printer status of each printer is displayed in the AXIS
NetPilot window.
UNIX
Macintosh
OS/2
Windows
NetWare
Monitoring Printers
AXIS 560/660 User’s Manual
AXIS NetPilot’s Monitoring Window
Creating a
printer group
Follow the instructions below to create a printer group:
1. Select the ‘Monitoring Printers’ folder.
2. Click on the New Group button on the toolbar or select New
Printer Group from the File menu.
3. Type a printer group name in the text field and click OK.
You can create as many printer groups as you want.
Adding a printer
to a printer group
Section 9: Management &amp; Configuration
Follow the instructions below to add a printer to a printer group:
1. Select the printer group folder, located in the ‘Monitoring
Printers’ folder.
123
NetWare
AXIS 560/660 User’s Manual
3. The Add Printer window appears. Double-click the print server,
to which the desired printer is connected and select the printer
port. Click OK.
1. Select the printer group folder, located in the ‘Monitoring
Printers’ folder. The printer status appear in the right-hand frame
of AXIS NetPilot.
OS/2
Follow the instructions below to monitor the printers:
Macintosh
2. If you want the status to appear in a new window, click the
Monitoring button on the AXIS NetPilot toolbar.
UNIX
Examining printers
Windows
2. Click on the Add Printer button on the toolbar or select Add
Printer from the File menu.
Windows
NetWare
124
Section 9: Management &amp; Configuration
Grouping logically
connected
Print Servers together
Creating a
Print Server Group
AXIS 560/660 User’s Manual
AXIS NetPilot allows you to create logical groups of print servers in
order to simplify administration. Installed print servers are displayed
in the ‘Network Print Servers’ folder and shortcuts to these print
servers can be added to the print server groups. Management
operations performed on the shortcuts affects the functionality of the
print servers.
Follow the instructions below to create a print server group:
1. Select the ‘AXIS Units’ folder.
2. Click on the New Group button on the toolbar or select New
Print Server Group from the File menu.
You can create as many print server groups as you want, but you
cannot include a print server in more than one group.
Adding a
Print Server to
a Print Server Group
Follow the instructions below to add a print server to a print server
group:
1. Select the print server group folder, located in the ‘AXIS Units’
folder.
2. Click on the Add PS button on the toolbar or select Add Print
Server from the File menu.
UNIX
Macintosh
OS/2
3. Type a print server group name in the text field and click OK.
3. The Add Network Print Server window appears. Select the print
server and click OK.
Examining
Print Servers
Follow the instructions below to monitor the print servers:
1. Select the print server group folder, located in the ‘AXIS Units’
folder.
2. Select the print server.
1. Select the desired printer folder, located in the ‘Monitoring
Printers’ folder.
2. Click the desired printer icon and choose Printer Information
from the File menu.
NetWare
Windows
❏ The extent of the detailed printer information is depending on
your printer model.
OS/2
Note:
Follow the instructions below to obtain detailed printer information
from printers appearing in the monitoring window:
125
Macintosh
Printer Information
Section 9: Management &amp; Configuration
AXIS NetPilot Printer Information window
UNIX
AXIS 560/660 User’s Manual
Section 9: Management &amp; Configuration
AXIS 560/660 User’s Manual
You can also view the detailed printer information in the Summary
window.
OS/2
Windows
NetWare
126
UNIX
Macintosh
AXIS NetPilot Summary window
Upgrading the Print
Server
You can use the AXIS NetPilot Upgrade Wizard to upgrade the AXIS
560/660 software. Please refer to Section 11 Upgrading the Software,
on page 147, for details.
Additional
information
Refer to the AXIS NetPilot on-line help for further information about
this tool.
Having assigned an IP address to your AXIS 560/660, as described in
Assigning an IP address on page 30, you can change the AXIS 560/660
parameter settings using the File Transport Protocol (FTP).
Editing the config file
Follow the instructions below to edit the config file using FTP:
1. Log in to the AXIS 560/660 by typing:
ftp &lt;host name&gt; or ftp &lt;IP address&gt; in a DOS window
(Windows and OS/2) or in a UNIX shell window.
2. Enter the user id and the password. (The default entries are root
and pass.)
3. Download the config file to your host by typing:
NetWare
Using FTP
127
Windows
Section 9: Management &amp; Configuration
OS/2
AXIS 560/660 User’s Manual
get config
put config CONFIG
Notes:
❏ It is important that the destination file is specified in capital
letters. Otherwise the edits are temporary and will be lost once the
AXIS 560/660 has been powered down.
❏ To edit the config file from a Macintosh you will need FTP
support such as MacTCP, Fetch or Anarchie. The procedure for
editing the file is the same as described above.
The example on the next page shows how to edit the config file using
FTP from a DOS window.
UNIX
5. Save the config file to the AXIS 560/660 by typing:
Macintosh
4. Edit the file using your preferred text editor.
128
Section 9: Management &amp; Configuration
AXIS 560/660 User’s Manual
NetWare
Example:
&gt; ftp npserver
connected to npserver.
220 AXIS 560/660 FTP Print Server v6.00 Jun 17 1999
ready.
Windows
Name (npserver:thomas): root
331 User name ok, need password
Password: pass
(not visible)
230 User logged in
ftp&gt; get config
OS/2
200 PORT command successful.
150 Opening data connection for config
(192,36,253,4,13,223), (mode ascii).
226 Transfer complete.
8588 bytes received in 0.24 seconds (35.63 kbytes/s)
ftp&gt; put config CONFIG
Macintosh
200 PORT command successful.
150 Opening data connection for CONFIG
(192,36,253,4,13,223), (mode ascii).
226 Transfer complete.
8588 bytes received in 0.45 seconds (19.04 kbytes/s)
ftp&gt; bye
UNIX
221 Goodbye.
&gt;
Viewing
the Status File
Section 9: Management &amp; Configuration
The status command shows which printer port the logical printers are
assigned to, and their current status.
Follow the instructions below to view the status file using FTP:
129
NetWare
AXIS 560/660 User’s Manual
2. Enter the user id and the password. (The default entries are root
and pass.)
3. Download the status file to your host by typing:
Windows
1. Log in to the AXIS 560/660 by typing:
ftp &lt;host name&gt; or ftp &lt;IP address&gt; in a DOS windows
(Windows and OS/2) or in a UNIX shell window.
The account file contains data concerning the 20 last print jobs. It
specifies an internal job number, the user that initiated the job, the
protocol and logical printer that was used, current status (Completed,
Off-line, or Printing), number of bytes printed, elapsed time and offline time.
Follow the instructions below to view the account file using FTP:
1. Log in to the AXIS 560/660 by typing:
ftp &lt;host name&gt; or ftp &lt;IP address&gt; in a DOS windows
(Windows and OS/2) or in a UNIX shell window.
2. Enter the user id and the password. (The default entries are root
and pass.)
3. Download the account file to your host by typing:
get account
4. View the account file using your preferred text editor.
FTP Help
By typing help in step 3 in the FTP instruction sets above, a list of all
available files and commands will be displayed.
Macintosh
Viewing
the Account File
UNIX
4. View the status file using your preferred text editor.
OS/2
get status
Macintosh
OS/2
Windows
NetWare
130
Section 9: Management &amp; Configuration
AXIS 560/660 User’s Manual
Using Telnet
Having assigned an IP address to your AXIS 560/660, as described in
Assigning an IP address on page 30, you can manage your AXIS
560/660 using the telnet protocol.
Viewing
the Account File
The account file contains data concerning the last 20 print jobs. It
specifies an internal job number, the user that initiated the job, the
protocol and logical printer that was used, current status (Completed,
Off-line, or Printing), number of bytes printed, elapsed time and offline time.
Follow the instructions below to view the account file using telnet:
1. Log in to the AXIS 560/660 by typing:
telnet &lt;host name&gt; or telnet &lt;IP address&gt; in a DOS
window (Windows and OS/2) or in a UNIX shell window.
2. Enter the user id and the password. (The default entries are root
and pass.)
3. View the account file by typing:
account
UNIX
The example on the next page shows how to view the account file using
Telnet from a UNIX window.
AXIS 560/660 User’s Manual
Section 9: Management &amp; Configuration
NetWare
Example:
131
&gt; telnet npserver
Trying 192.36.253.96...
Connected to npserver.
Escape character is ‘^]’.
1
2
3
4
5
6
Root&gt;
Thomas
FTP
Joe
LPT
RICHARD PSERVER
MacUser APPLE
LSLM_userNetBIOS
patrick PROS
LPR S BYTES ETIME OTIME
pr2
pr1
pr2
pr1
pr2
pr5
C
C
C
C
C
P
1885
23074
43044
6717
36995
83208
Typical Telnet session to view the Account File
2
4
5
2
3
9
0
0
0
0
0
0
OS/2
Root&gt; account
Current account file:
JOB
USER
PROT
Macintosh
AXIS 560/660 TELNET Print Server v6.00 Jun 17 1999
UNIX
AXIS 560/660 network login: root
(not visible)
Password: pass
Windows
AXIS 560/660 TELNET Print Server v6.00 Jun 17 1999
Section 9: Management &amp; Configuration
Viewing
the Status file
AXIS 560/660 User’s Manual
The status command shows which printer port the logical printers are
assigned to, and their current status.
Follow the instructions below to view the status file using telnet:
1. Log in to the AXIS 560/660 by typing:
telnet &lt;host name&gt; or telnet &lt;IP address&gt; in a DOS
windows (Windows and OS/2) or in a UNIX shell window.
Windows
NetWare
132
2. Enter the user id and the password. (The default entries are root
and pass.)
3. View the status file by typing:
OS/2
status
Performing resets
Three types of reset commands allow you to perform soft resets, to
perform hard resets, and to reset the print server’s parameters to its
factory default settings.
Macintosh
Follow the instructions below to perform a soft reset using telnet:
1. Log in to the AXIS 560/660 by typing:
telnet &lt;host name&gt; or telnet &lt;IP address&gt; in a DOS
windows (Windows and OS/2) or in a UNIX shell window.
2. Enter the user id and the password. (The default entries are root
and pass.)
UNIX
3. Restart the print server’s protocols by typing:
softreset
Replace the command in step 3 above with hardreset or default to
perform the other two reset operations.
Telnet Help
By typing help in step 3 in any of the Telnet instruction sets above, a
list of all available commands will be displayed.
General Information
SNMP refers to a set of standards for network management, including
a protocol, a database structure specification, and a set of data objects.
The AXIS 560/660 SNMP implementation runs in TCP/IP and
NetWare (IPX) networks.
The management is handled by NMS (Network Management System)
software running on a host on your network. The NMS software
communicates with network devices by the means of messages, which
are references to one or more objects.
A message can be a question or an instruction to a device, or an alarm
triggered by a specific event in a device. Objects are contained in data
bases called MIBs (Management Information Base), where MIB-II is a
standard database.
The AXIS 560/660 supports all relevant parts of MIB-II and of the
host resources MIB. The AXIS 560/660 also includes a private
enterprise MIB, the AXIS MIB.
NetWare
Windows
You can use SNMP (Simple Network Management Protocol) for
remotely monitoring and configuring of the AXIS 560/660. All major
functions for print servers are supported.
OS/2
Using SNMP
133
Macintosh
Section 9: Management &amp; Configuration
UNIX
AXIS 560/660 User’s Manual
134
Section 9: Management &amp; Configuration
Macintosh
OS/2
Windows
NetWare
The AXIS MIB
AXIS 560/660 User’s Manual
In order to make full use of the AXIS 560/660 SNMP support, you
are required to use NMS software that allows you to install private
enterprise MIBs, like the AXIS MIB.
The AXIS MIB contains a large number of objects which may be
categorized as follows:
•
Menu objects - used for viewing and changing the AXIS 560/660
configuration from the NMS program. Refer to B - The Parameter
List, on page 153.
•
Printer status and unit administration objects - used for
monitoring AXIS 560/660 print jobs and storing parameter
changes permanently.
•
Trap objects - used for alarms at various error conditions.
For technical details, you can view the MIB file (axis.mib) with any
text editor.
The AXIS MIB is resident on the AXIS 560/660 and can be
downloaded directly from the print server to your NMS software
using FTP.
Follow these steps to add the AXIS MIB to your NMS software:
UNIX
1. Log in to the AXIS 560/660 using FTP.
2. Download the MIB file /snmp/axis.mib to the NMS host.
3. Install the AXIS MIB according to instructions in your NMS
software documentation.
Please refer to the appropriate Hewlett Packard documentation for
further details about these tools.
Notes:
❏ To enable support for the HP JetAdmin and the HP Web
JetAdmin management software, you must set the
HP_JETADMIN parameter to YES.
❏ It is not possible to upgrade the AXIS 560/660 Flash Memory
from the HP JetAdmin.
❏ If the AXIS 560/660 has been configured with HP JetAdmin or
HP Web JetAdmin, you cannot configure it with AXIS NetPilot
unless you first reset it to the factory default settings.
NetWare
Windows
The AXIS 560/660 is fully compatible with the HP JetAdmin and the
HP Web JetAdmin printer management software. You can use either
tool to install and configure your printer devices, and to monitor the
current status of your AXIS 560/660 and the connected printers.
OS/2
Using HP Administration Tools
135
Macintosh
Section 9: Management &amp; Configuration
UNIX
AXIS 560/660 User’s Manual
136
Section 9: Management &amp; Configuration
NetWare
Exceptions
UNIX
Macintosh
OS/2
Windows
The print server
concept
AXIS 560/660 User’s Manual
Even though the AXIS 560/660 is fully compatible with the HP
JetAdmin tool, the AXIS 560/660 behaves differently in certain
situations. The exceptions from the traditional HP JetAdmin
functionality are presented below.
HP JetAdmin considers the AXIS 560/660 as one print server,
independently on the number of supported ports. The effects of this
behavior are:
•
You can change a printers port’s properties from any of the AXIS
560/660 printer ports’ property pages. This can not be done with
an HP print server.
•
If you are performing a reset on one of the AXIS 560/660 printer
ports, all three ports will be reset.
•
From each port you can view all print queues connected to the
print server and not only the queues connected to the specific
printer port. To be able to distinguish between the queues, they
must be named &lt;queue_name&gt;!&lt;logical_printer_number&gt;.
•
The AXIS 560/660 printer ports have the same name. They are
only distinguished by suffixes. If you change the name on one of
the AXIS 560/660 printer ports, all three port names will be
changed. Note that the port names displayed in HP JetAdmin will
not change until one of the refresh commands in the Device
Refresh menu has been performed.
1. Start the AXIS NetPilot.
2. Select your AXIS 560/660 and click Install on the AXIS NetPilot
toolbar. Select with current configuration.
3. Your AXIS 560/660 has been transferred to the ‘Network Print
Servers’ folder. Select your AXIS 560/660 and click the Property
button on the AXIS NetPilot toolbar.
4. Select the Printer Ports tab.
NetWare
Windows
HP JetAdmin does not support serial printer ports. If you must change
the default settings of the serial printer port of the AXIS 560/660, it is
recommended that you use the AXIS NetPilot. This will become
necessary when you are installing a printer on your serial port. Follow
the steps below to change the serial port parameters using AXIS
NetPilot.
137
6. Select XON/XOFF from the Handshake Protocol drop-down list,
set the Baud Rate to 38400 and select 1 stop bit. Click OK.
The settings in step 6 varies between different printer models. Please
refer to your printer documentation.
Macintosh
5. Select COM1 from the Printer Port drop-down list.
If your network supports TCP/IP you can also change the serial port
parameters by using the AXIS 560/660 Web interface.
UNIX
The Serial Printer Port
Section 9: Management &amp; Configuration
OS/2
AXIS 560/660 User’s Manual
Windows
NetWare
138
Section 9: Management &amp; Configuration
Using Novell Utilities
After installing the AXIS 560/660 into the NetWare environment,
you can manage your AXIS 560/660, using either Novell’s NetWare
Administrator, or PCONSOLE.
NetWare
Administration
Printer Status
Some useful features provided by the NetWare Administrator are
described in more detail below:
The Printer Status menu, detailed below, shows the status of an active
print job serviced by an AXIS 560/660 network print server. It
displays detailed information concerning the active job including,
Print Queue, print job description, size of print file, percentage of job
completed, etc. You can also abort or pause the print job from this
menu.
UNIX
Macintosh
OS/2
AXIS 560/660 User’s Manual
NetWare Administrator Printer Status Menu
You can use the NetWare Administrator to enable or disable status
notification messages for printers connected to the AXIS 560/660, e.g.
Busy, Off-line, Out of paper, Paper jam, etc. You can also add or
remove print job owners and administrators from the list of persons to
be notified.
Print Layout
You can view installed AXIS 560/660 Network Print Servers and their
relative print queues for any NetWare Organizational Unit. You can
also display summary information by right-clicking on the printer
object you want to examine.
UNIX
Macintosh
OS/2
Notification
139
NetWare
Section 9: Management &amp; Configuration
Windows
AXIS 560/660 User’s Manual
NetWare Print Layout with corresponding information summary
Section 10: IPP
AXIS 560/660 User’s Manual
Section 10 IPP
Overview
IPP (Internet Printing Protocol) is a TCP/IP based client-server
protocol. IPP enables printing over any LAN or WAN supporting
TCP/IP. The most prevalent example of this is IPP printing over the
Internet, which is illustrated below.
Macintosh
Macintosh
OS/2
OS/2
Windows
Windows
NetWare
NetWare
140
UNIX
UNIX
Figure: The path of a print job from LAN to LAN over the Internet
In practical terms this means that you can send documents to a remote
printer as an addition to or replacement of fax and e-mail, with the
same quality and color options of traditional network printing.
IPP is platform independant and functional in Windows (NT, 95, 98
and 2000), Macintosh, OS/2, NetWare and UNIX environments.
Currently available IPP clients include:
•
the Internet Printer Connection software from Hewlett Packard
for WindowsNT,
•
the Microsoft IPP Client delivered with Windows 2000,
•
IPP clients for Windows ‘95 and ‘98 that can be downloaded
from the Microsoft web site.
•
the Common Unix Printing System for Unix/Linux
environments.
Firewall
Considerations
If there are one or more firewalls between the IPP Client and the
server, you may have to make some changes to the firewall
configuration. IPP uses TCP port 631 for printing, so any firewalls
between client and server must be configured to allow bi-directional
traffic on that port. Please consult your network administrator if you
think any configuration changes are neccesary.
IPP Compliance
The Axis print server with integrated IPP is compatible with any 1.0
and 1.1 - compliant IPP client. The AXIS 560/660 Print Server
presents IPP Printer objects to the client, one for each printer port.
Note:
Axis firmware including IPP can be down-loaded free of charge
from the Axis website http://www.axis.com.
The details on how to print will vary between different IPP
clients. Please refer to your client documentation for more specific
information.
NetWare
NetWare
Windows
Windows
The IPP protocol does not require any special configuration of the
print server, the IPP function is automatically activated when you
install your AXIS 560/660 Print Server.
OS/2
OS/2
User Requirements
141
Macintosh
Macintosh
Section 10: IPP
UNIX
UNIX
AXIS 560/660 User’s Manual
Section 10: IPP
Macintosh
Macintosh
UNIX
UNIX
AXIS 560/660 User’s Manual
Address Schemes
When using IPP printing, you need to know the IP address or host
name of your IPP-enabled Axis print server. The AXIS 560/660 Print
Server supports the http: address scheme (which is used in the IPP 1.0
standard), and the ipp: adress scheme (used in the IPP 1.1 standard).
The examples given below assume that the host name of the Axis print
server is axisps and that the corresponding IP adress is 12.100.110.2.
Example
OS/2
OS/2
Windows
Windows
NetWare
NetWare
142
http: address schemes.
IPP address using host name
IPP address using IP address
Corresponding printer
http://axisps:631/LPT1
http://12.100.110.2:631/LPT1
Printer attached to the LPT1
parallel port
http://axisps:631/LPT2
http://12.100.110.2:631/LPT2
Printer attached to the LPT2
parallel port
http://axisps:631/COM1
http://12.100.110.2:631/COM1
Printer attached to the COM1
serial port
Note that the IPP port number (631) should be specified in the http:
address scheme.
Example
ipp: address schemes.
IPP address using host name
IPP address using IP address
Corresponding printer
ipp://axisps/LPT1
ipp://12.100.110.2/LPT1
Printer attached to the LPT1
parallel port
ipp://axisps/LPT2
ipp://12.100.110.2/LPT2
Printer attached to the LPT2
parallel port
ipp://axisps/COM1
ipp://12.100.110.2/COM1
Printer attached to the COM1
serial port
The URL for the destination printer is defined in the print server host
name, the port number and the local printer name, in that order.
When using IPP printing over the Internet with the AXIS 560/660,
the host name used for the Axis print server could be “axisps”, for
example. The port number used is 631, followed by the local printer
name (Ex. LPT1).
A walk-through example of the IPP printing process is perhaps the
best way to describe the IPP functionality:
1. As a LAN-user in a Windows environment, you wish to print a
document on a color printer which is integrated in another LAN
and located in another city.
2. Proceed with selecting the IPP printer to which you want to send
your document from your Printer Name list (In File | Print). The
name structure of the printer begins with http://axisps:631/....
3. If your destination printer URL does not exist in your Printer
Name list, you need to add it. (See the examples below for
Windows environments).
4. When you press Print, the print job is sent over the Internet to
the AXIS 560/660 print server which sends the job to the
destination printer.
NetWare
NetWare
Windows
Windows
In order to print using IPP, you need to be able to access a printer
which is connected to the AXIS 560/660, which has integrated IPP.
Once you have access to the destination printer, you are ready to print
to the printer of your choice via, for example, the Internet.
OS/2
OS/2
How It Works
143
Macintosh
Macintosh
Section 10: IPP
UNIX
UNIX
AXIS 560/660 User’s Manual
144
Section 10: IPP
NetWare
NetWare
Example
AXIS 560/660 User’s Manual
Adding an IPP printer in Windows ‘95 for printing with the
Microsoft IPP Client:
In this example we will assume the printers’ http: address is
http://axisps:631/LPT1:
Windows
Windows
To add a destination printer for IPP printing in Windows ‘95:
1. Open Start | Settings | Printers.
2. Choose Add Printer. The Add Printer Wizard will start.
Follow the instructions on the screen.
OS/2
OS/2
3. When prompted, choose Network Printer.
4. In the Network Path or Queue name field, write the
http: address of the destination printer, for example:
http://axisps:631/LPT1.
UNIX
UNIX
Macintosh
Macintosh
5. Select the appropriate printer driver corresponding to the
destination printer.
6. Specify a name for the printer you wish to add to your
printer list. Click Finish. The destination printer will be
added to your printer list.
You are now ready to print using IPP.
For information on how to use IPP in other environments,
please refer to the documentation supplied with your IPP
client.
Adding an IPP printer in Windows ‘98 for printing with the
Microsoft IPP Client:
In this example we will assume the printers’ http: address is
http://axisps:631/LPT1:
145
2. Choose Add Printer. The Add Printer Wizard will start.
Follow the instructions on the screen.
3. When prompted, choose Network Printer.
4. In the Network Path or Queue name field, write the
http: address of the destination printer, for example:
http://axisps:631/LPT1.
OS/2
OS/2
1. Open Start | Settings | Printers.
Windows
Windows
To add a destination printer for IPP printing in Windows ‘98:
6. Specify a name for the printer you wish to add to your
printer list. Click Finish. The destination printer will be
added to your printer list.
You are now ready to print using IPP.
For information on how to use IPP in other environments,
please refer to the documentation supplied with your IPP
client.
Macintosh
Macintosh
5. Select the appropriate printer driver corresponding to the
destination printer.
UNIX
UNIX
Example
Section 10: IPP
NetWare
NetWare
AXIS 560/660 User’s Manual
146
Section 10: IPP
NetWare
NetWare
Example
AXIS 560/660 User’s Manual
Adding an IPP printer in Windows 2000 for printing with the
Microsoft IPP Client:
In this example we will assume the printers’ http: address is
http://axisps:631/LPT1.
Windows
Windows
If you want to print via IPP from Windows 2000:
1. Choose File | Print.
2. If you need to enter a new destination printer, click Find
Printer in the Select Printer frame.
OS/2
OS/2
5. Specify your printer from the printer list. Click Print.
UNIX
UNIX
4. The Installation Wizard will ask you if you want to install
the appropriate printer driver on your computer. Click
OK. Select the printer driver corresponding to your
destination printer. Click OK.
Macintosh
Macintosh
3. Enter the printer http: address in the Printer field, for
example http://axisps:631/LPT1. Click OK.
You are now ready to print using IPP.
For information on how to use IPP in other environments,
please refer to the documentation supplied with your IPP
client.
•
AXIS NetPilot configuration software
•
AXIS ThinWizard
•
AXIS Print System
•
AXIS Print Utility for Windows
•
AXIS Print Utility for OS/2
•
The AXIS 560/660 print server software held in Flash Memory
•
The axinstall script
•
The AXIS MIB file
Obtaining the Updated Software
You can obtain all the print server software as well as the latest utility
software from the following locations:
Note:
•
AXIS Online CD
•
Over the Internet, by accessing the AXIS home page at
http://www.axis.com
•
Anonymous ftp, by logging in to ftp.axis.com and accessing the
folder /pub/axis/
•
your local dealer
❏ If you are upgrading your print servers using AXIS ThinWizard,
you do not need to obtain the firmware file prior to the upgrading
process, provided that you are connected to the Internet.
NetWare
Windows
The following software can be upgraded free of charge:
OS/2
Section 11 Upgrading the Software
147
Macintosh
Section 11: Upgrading the Software
UNIX
AXIS 560/660 User’s Manual
Section 11: Upgrading the Software
AXIS 560/660 User’s Manual
Upgrading the Firmware Software
You can upgrade the AXIS 560/660 Flash memory using one of the
following methods:
Windows
NetWare
148
AXIS ThinWizard (TCP/IP)
•
FTP (TCP/IP)
•
AXIS NetPilot Upgrade Wizard (IPX/SPX)
❏ Updating instructions are also supplied with the software update.
OS/2
Note:
•
Macintosh
Upgrading using
AXIS ThinWizard
AXIS ThinWizard is a tool that enables batch upgrading of several
print servers and should be used for upgrading the flash memory in
TCP/IP networks.
You must assign the AXIS 560/660 with an IP address, as described in
Assigning an IP address, on page 30, before you can use this upgrading
method.
UNIX
Follow the instructions below to upgrade your print servers using
AXIS ThinWizard:
1. Click the Manage Network button in the AXIS ThinWizard
main menu.
2. Select a network group from the drop-down list. You can only
update the servers that are included in the selected network group.
3. All AXIS servers included in the network group appear. Click the
Firmware button to start the Upgrade Wizard.
4. Follow the instructions that are presented to you to complete the
installation.
Refer to Using AXIS ThinWizard, on page 115, for more information
about AXIS ThinWizard.
Follow the procedures below to upgrade the AXIS 560/660:
Caution!
❏ Be careful not to interrupt the file transfer. If the transfer is
interrupted the AXIS 560/660 may have to be re-initialized by
your dealer.
1. Log in to the AXIS 560/660 with the command:
ftp &lt;host name&gt;, or ftp &lt;IP address&gt;
2. You will be prompted for user id and password. Use the user id
root, which has the default password pass.
3. Type the command:
binary
NetWare
Windows
You must assign the AXIS 560/660 with an IP address, as described in
Assigning an IP address, on page 30, before you can use this upgrading
method.
OS/2
To upgrade over the network using FTP you will need the file with the
new print server software. The name of this file is in the form
product_version.bin, e.g. 560_600.bin for software release 6.00.
You can use any of the previously mentioned methods to obtain the
new file.
149
to change to binary transfer mode.
4. Type the command:
put &lt;software name&gt; FLASH
where &lt;software name&gt; is the name of the new print server
software, e.g. 560_600.bin
5. Wait for the Flash loading operation to finish. This normally
takes 1 to 4 minutes. The unit automatically restarts with the new
print server software.
6. Log out using the command:
quit, bye
or exit
depending on your FTP version.
UNIX
Upgrading over the
Network using FTP
Section 11: Upgrading the Software
Macintosh
AXIS 560/660 User’s Manual
150
Section 11: Upgrading the Software
Windows
NetWare
Note:
Upgrading using
AXIS NetPilot
AXIS 560/660 User’s Manual
❏ Should you encounter any problem that prevents a successful
upgrade over your network, it may become necessary to perform
the flash loading operation via the parallel port, LPT1. In this
case, you are advised to contact your dealer.
This method is recommended for upgrading the flash memory in
NetWare networks. An Upgrade Wizard is available to guide you
through the necessary procedures.
OS/2
Follow the instructions below to upgrade your print servers:
1. Obtain the firmware file, using one of the methods presented on
page 147.
UNIX
Macintosh
2. Put the file in the AXIS NetPilot ‘Upgrade’ folder. This folder
resides in the same folder as the AXIS NetPilot program and was
created when AXIS NetPilot was installed on your client.
3. Start the Upgrade Wizard by clicking on the Upgrade icon on the
AXIS NetPilot toolbar.
4. Proceed the installation by following the instructions that are
presented to you in the Upgrade Wizard.
If you need more information, please refer to AXIS NetPilot on-line
help.
The Test Page
Note:
The Parameter List
•
Printing a test page, checking the connection to the printer.
•
Printing a parameter list, showing the AXIS 560/660 current settings.
•
Resetting the AXIS 560/660 parameters to the factory default
settings.
Press the test button once to print a test page. If the test page prints,
the parallel interface is functioning correctly. The printed Test Page
contains basic information about the AXIS 560/660. It is
recommended that you print a test page every time you have
connected the AXIS 560/660 to a printer.
❏ The test page is printed on LPT1 by default. If you want to print
the test page on LPT2 or COM1 instead, you should set the
Internal Printout Destination parameter to LPT2 respectively
COM1.
Press the test button twice to print a parameter list showing the
current AXIS 560/660 settings. This list provides comprehensive
details of all the parameters and their current status. Refer to
B - The Parameter List, on page 153.
If you want to change any of the parameters, use one of the methods
that are described in
Section 9 Management &amp; Configuration, on page 108.
Note:
❏ The parameter list is printed on LPT1 by default. If you want to
print the parameter list on LPT2 or COM1 instead, you should
set the Internal Printout Destination parameter to LPT2
respectively COM1.
NetWare
Windows
The test button is located on the front right hand side of the AXIS
560/660 and is used for:
OS/2
Appendix A Test Button
151
Macintosh
Appendix A: Test Button
UNIX
AXIS 560/660 User’s Manual
Appendix A: Test Button
Factory Default
Settings
AXIS 560/660 User’s Manual
Follow the instructions below to reset the AXIS 560/660 to the factory
default settings:
1. Remove the external power supply to switch off the AXIS
560/660.
2. Press and hold down the test button, while you plug the external
power supply back in. Continue to hold down the test button,
until the network indicator begins to flash at one second intervals.
This should take at least 5 seconds.
Windows
NetWare
152
3. Release the test button and wait until the network indicator
flashes at least five times.
OS/2
4. Press and hold the test button again until the network indicator
remains constantly lit.
5. Restart the AXIS 560/660 by disconnecting and reconnecting the
external power supply.
UNIX
Macintosh
The AXIS 560/660 is now reset to factory default settings.
Note:
❏ All parameters except Node Address (NODE_ADDR), Internet
Address (IP_ADDR) and DHCP enabled or disabled
(DHCP_ENABLE.) are reset. If you want to change the these
parameters, use either AXIS NetPilot or any standard Web
browser. Please refer to Section 9 Management &amp; Configuration,
on page 108.
The Config File
The left-hand column shows the parameters and their default values as
they appear in the config file and the right-hand column shows the
name of the parameters as they appear in the internal Web pages.
After you have changed them, most parameters take effect for the next
print job. If Requires Restart appears in a parameter description, you
must restart the AXIS 560/660, before the new setting for that
parameter takes effect.
Please refer to Section 9 Management &amp; Configuration, on page 108,
for more information about how to change the parameters.
Note:
❏ The password parameters, ROOT_PWD and PROS_PWD only
appear when you are logged in to the AXIS 560/660 using root.
The password parameters will not be printed when you are
printing the parameter list using the test button.
--- GENERAL MENU
NODE_ADDR.
: 00 40 8C 10 00 86
PS_NAME.
: AXIS100086
ROOT_PWD.
: pass
USERS.
:
BASE_URL.
: www.axis.com
AXIS_PRINT_SYSTEM.: YES (YES, NO)
S_ROUTE.
: AUTO (OFF, SINGLE, ALL, AUTO)
HP_JETADMIN. : NO (YES, NO)
DEF_OUT.
: PR1
(PR1, PR2, PR3, PR4,
PR5, PR6, PR7, PR8, LPT1,
COM1, LPT2)
SYS_LOC.
:
SYS_CONT.
:
Node Address
Print Server Name (100086 are the last six digits of the serial number)
Root Password
User and Printer Access List
Base URL
Enable compatibility with AXIS Print System
Token Ring Source Routing Mode (AXIS 660 only)
HP JetAdmin Support
Internal Printout Destination
System Location
System Contact
NetWare
Windows
This appendix provides an overview of the AXIS 560/660 parameters.
Please refer to the AXIS Network Print Server Technical Reference for
a complete description of the parameters. Alternatively, you can access
the Axis WWW Home Page at http://www.axis.com/, where you can
download the latest technical information.
OS/2
Appendix B The Parameter List
153
Macintosh
Appendix B: The Parameter List
UNIX
AXIS 560/660 User’s Manual
UNIX
Macintosh
OS/2
Windows
NetWare
154
Appendix B: The Parameter List
AXIS 560/660 User’s Manual
--- TCP/IP MENU
DNS_ENB.
: YES
DNS_ADDR1.
: 0 0 0 0
DNS_ADDR2.
: 0 0 0 0
DOMAIN_NAME. :
SLP_SCOPE_LIST.: DEFAULT
RTN_OPT.
: NO
RTEL_PR1.
: 0
RTEL_PR2.
: 0
RTEL_PR3.
: 0
RTEL_PR4.
: 0
RTEL_PR5.
: 0
RTEL_PR6.
: 0
RTEL_PR7.
: 0
RTEL_PR8.
: 0
TCP/IP Enabled
Internet Address
Default Router Address
(0.0.0.0 for no router)
Net Mask
(e.g. 255.255.255.0 for class C, 0.0.0.0 for auto-sense)
PROS Password
PROS TCP Port Number
LPD Banner Page Mode
DHCP Enabled
BOOTP Enabled
RARP Enabled
WINS Enabled
Primary WINS Server Address
Secondary WINS Server Address
NBT Scope ID
(Defines the NetBIOS scope to be used with WINS name registration)
DNS Enabled
Primary DNS Server Address
Secondary DNS Server Address
Domain Name (Defines the domain to which the AXIS 560/660 belongs)
Defines the SLP scope to which the AXIS 560/660 belongs.
Reverse Telnet Options Enabled
PR1 Reverse Telnet Port Number
PR2 Reverse Telnet Port Number
PR3 Reverse Telnet Port Number
PR4 Reverse Telnet Port Number
PR5 Reverse Telnet Port Number
PR6 Reverse Telnet Port Number
PR7 Reverse Telnet Port Number
PR8 Reverse Telnet Port Number
--- SNMP MENU
READ_COM.
: public
WRT_COM.
: pass
TRAPADDR.
: 0 0 0 0
TRAP_COM.
: public
SYS_NAME.
:
SNMP_AUT.
: DISABLE
TRAP_PRT.
: DISABLE
Read Community
Read/Write Community
Trap Address
Trap Community
System Name
Authentication Failure Trap
Printer Failure Trap
TCP_ENB.
: YES
INT_ADDR.
: 0 0 0 0
DEF_ROUT.
: 0 0 0 0
NET_MASK.
: 0 0 0 0
PROS_PWD.
: netprinter
PROS_PRT.
: 35
LPD_BANN.
DHCP_ENB.
BOOTP_ENB.
RARP_ENB.
WINS_ENB.
WINS_ADDR1.
WINS_ADDR2.
NBT_SCOPE_ID.
:
:
:
:
:
:
:
:
OFF (OFF, AUTO, LAST)
YES
YES
YES
YES
0 0 0 0
0 0 0 0
(DISABLE, ENABLE)
(DISABLE, ENABLE)
CONF_CHECK_DELAY.
: 300
FR_802_3.
: YES
FR_ETH_2.
FR_802_2.
FR_SNAP.
NCP_BURST_MODE.
:
:
:
:
PSERVER_NDS.
:
YES
YES
YES
YES
Job Check Delay
(Print Server queue polling interval)
Configuration Check Delay
(Interval between automatic configuration checks)
IEEE 802.3 Frame Type Enabled
Ethernet II Frame Type Enabled
IEEE 802.2 Frame Type Enabled
SNAP Frame Type Enabled
NCP Burst Mode Enabled (Requires Restart)
PSERVER NDS
(NDS tree &amp; Name of print server, including context. You can also replace
the NDS tree with a specific file server name, file server IP address or file
server host name.)
Example (tree): TREE:NW5_TREE DevDept.acme
PSERVER_BINDERY1.
PSERVER_BINDERY2.
PSERVER_BINDERY3.
PSERVER_BINDERY4.
:
:
:
:
PSERVER_BINDERY5.
PSERVER_BINDERY6.
PSERVER_BINDERY7.
PSERVER_BINDERY8.
PSERVER_BINDERY9.
PSERVER_BINDERY10.
PSERVER_BINDERY11.
PSERVER_BINDERY12.
PSERVER_BINDERY13.
PSERVER_BINDERY14.
PSERVER_BINDERY15.
PSERVER_BINDERY16.
NPRINTER1.
NPRINTER2.
NPRINTER3.
NPRINTER4.
NPRINTER5.
NPRINTER6.
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
NPRINTER7.
NPRINTER8.
:
:
Example (file server): Specific_file_server DevDept.acme
PSERVER Bindery 1 (Bindery file server name)
PSERVER Bindery 2 (Bindery file server name)
PSERVER Bindery 3 (Bindery file server name)
PSERVER Bindery 4 (Bindery file server name)
PSERVER Bindery 5 (Bindery file server name)
PSERVER Bindery 6 (Bindery file server name)
PSERVER Bindery 7 (Bindery file server name)
PSERVER Bindery 8 (Bindery file server name)
PSERVER Bindery 9 (Bindery file server name)
PSERVER Bindery 10 (Bindery file server name)
PSERVER Bindery 11 (Bindery file server name)
PSERVER Bindery 12 (Bindery file server name)
PSERVER Bindery 13 (Bindery file server name)
PSERVER Bindery 14 (Bindery file server name)
PSERVER Bindery 15 (Bindery file server name)
PSERVER Bindery 16 (Bindery file server name)
NPRINTER/RPRINTER 1 (Print Server name and slot number)
NPRINTER/RPRINTER 2 (Print Server name and slot number)
NPRINTER/RPRINTER 3 (Print Server name and slot number)
NPRINTER/RPRINTER 4 (Print Server name and slot number)
NPRINTER/RPRINTER 5 (Print Server name and slot number)
NPRINTER/RPRINTER 6 (Print Server name and slot number)
NPRINTER/RPRINTER 7 (Print Server name and slot number)
NPRINTER/RPRINTER 8 (Print Server name and slot number)
NetWare
NetWare Enabled
NetWare Transport protocols Enabled
Windows
: YES
NETW_TRANSPORT_PROTOCOL. : DUAL_STACK (IPX_ONLY,
IP_ONLY, DUAL_STACK)
JOB_CHECK_DELAY.
: 5
OS/2
NETWARE MENU
NETW_ENB.
155
Macintosh
---
Appendix B: The Parameter List
UNIX
AXIS 560/660 User’s Manual
NetWare
156
Appendix B: The Parameter List
---
NetBIOS/NetBEUI MENU
LSLM_ENB.
: YES
NB_FR_TYPE.
: FR_AUTO (FR_AUTO, FR_802_2, FR_DIX)
LPRINT_1.
: AX100086.LP1
LLOGIC_1.
: PR1 (PR1, PR2, PR3, PR4, PR5, PR6, PR7,
PR8, LPT1, LPT2, COM1)
: AX100086.LP2
: PR2 (PR1, PR2, PR3, PR4, PR5, PR6, PR7,
PR8, LPT1, LPT2, COM1)
: AX100086.CM1
Windows
LPRINT_2.
LLOGIC_2.
LPRINT_3.
LLOGIC_3.
LPRINT_4.
LLOGIC_4.
OS/2
LPRINT_5.
LLOGIC_5.
LPRINT_6.
LLOGIC_6.
LPRINT_7.
LLOGIC_7.
Macintosh
LPRINT_8.
LLOGIC_8.
UNIX
AXIS 560/660 User’s Manual
--- APPLETALK
ATLK_ENB.
ATK_ZONE.
ZONER_EN.
ATK_FONT.
APRINT_1.
ATYPE_1.
ALOGIC_1.
: PR3 (PR1, PR2, PR3, PR4, PR5,
PR8, LPT1, LPT2, COM1)
:
: PR4 (PR1, PR2, PR3, PR4, PR5,
PR8, LPT1, LPT2, COM1)
:
: PR5 (PR1, PR2, PR3, PR4, PR5,
PR8, LPT1, LPT2, COM1)
:
: PR6 (PR1, PR2, PR3, PR4, PR5,
PR8, LPT1, LPT2, COM1)
:
: PR7 (PR1, PR2, PR3, PR4, PR5,
PR8, LPT1, LPT2, COM1)
:
: PR8 (PR1, PR2, PR3, PR4, PR5,
PR8, LPT1, LPT2, COM1)
NetBIOS/NetBEUI Enabled
NetBIOS Frame Type (Requires Restart)
Name Printer 1 (100086 are the last six characters of the serial number)
Logical Printer for Printer 1
Name Printer 2 (100086 are the last six characters of the serial number)
Logical Printer for Printer 2
PR6, PR7,
Name Printer 3 (100086 are the last six characters of the serial number)
Logical Printer for Printer 3
PR6, PR7,
Name Printer 4 Name
Logical Printer for Printer 4
PR6, PR7,
Name Printer 5
Logical Printer for Printer 5
PR6, PR7,
Name Printer 6
Logical Printer for Printer 6
PR6, PR7,
Name Printer 7
Logical Printer for Printer 7
PR6, PR7,
Name Printer 8
Logical Printer for Printer 8
MENU (AXIS 560 only)
: YES
:
: YES
: DEFAULT
(DEFAULT, 35N, ALL)
: AXIS100086_LPT1
: LaserWriter
: PR1 (PR1, PR2, PR3, PR4,
PR5, PR6, PR7, PR8, LPT1, LPT2, COM1)
BINARY_TYPE_1.: TBCP (TBCP, BCP, NONE)
APRINT_2.
: AXIS100086_LPT2
ATYPE_2.
: LaserWriter
ALOGIC_2.
: PR2 (PR1, PR2, PR3, PR4,
PR5, PR6, PR7, PR8, LPT1, LPT2, COM1)
BINARY_TYPE_2.: TBCP (TBCP, BCP, NONE)
APRINT_3.
: AXIS100086_COM1
ATYPE_3.
: LaserWriter
ALOGIC_3.
: PR2 (PR1, PR2, PR3, PR4,
PR5, PR6, PR7, PR8, LPT1, LPT2, COM1)
BINARY_TYPE_3.: TBCP (TBCP, BCP, NONE)
AppleTalk Enabled
AppleTalk Zone
HP Zoner Enabled
Font
(PostScript Font Set)
Name Printer 1 (100086 are the last six digits of the serial number)
Type Printer 1
Logical Printer for Printer
Binary Protocol for APRINT_1
Name Printer 2
Type Printer 2
Logical Printer for Printer 2
Binary Protocol for APRINT_2
Name Printer 3
Type Printer 3
Logical Printer for Printer 3
Binary Protocol for APRINT_3
PRINTER1 MENU
PR1_OUT.
: LPT1
PR1_SND.
PR1_WAIT.
: PR1 (PR1, PR2, PR3, PR4,
PR5, PR6, PR7, PR8
: YES
(LPT1, COM1, LPT2)
PR1_IN.
: AUTO
PR1_BEF.
:
PR1_STR.
:
PR1_CSET.
: NONE
PR1_FILT.
PR1_AFT.
PR1_DUMP.
: NONE
:
: NO
PR1_SIZE.
PR1_ORNT.
PR1_FORM.
:
:
:
PR1_FONT.
:
Wait on Busy
Read Back Port
(Read-Back of information)
String Before Print Job
String Substitutions
(NONE, ISO&gt;IBM, 7UK&gt;IBM, 7SW&gt;IBM, Character Set Conversion
String After Print Job
Hex Dump Mode Enabled
A4
(A4, LETTER, LEGAL, EXECUT)
PostScript Page Size
PORTR
(PORTR, LANDS, R_PORTR, R_LANDS) PostScript Page Orientation
66 0 100 60 30 50
PostScript Page Format
(MPL, MPP, CPI, LPI, LM, TM)
PostScript Font
(Courier when not specified)
:
:
: NONE
PR2_FILT.
PR2_AFT.
PR2_DUMP.
PR2_SIZE.
: NONE
:
: NO
: A4
PR2_FONT.
Physical Port
Secondary Printer
Wait on Busy
Read back Port
(Read-Back of information)
String Before Print Job
String Substitutions
(NONE, ISO&gt;IBM, 7UK&gt;IBM, 7SW&gt;IBM, Character Set Conversion
Macintosh
PR2_BEF.
PR2_STR.
PR2_CSET.
OS/2
7GE&gt;IBM, 7FR&gt;IBM, 7ND&gt;IBM, DEC&gt;IBM)
(NONE, POSTSCR, AUTO_PS)
Printer Language Translation
Windows
(NONE, AUTO)
--- PRINTER2 MENU
PR2_OUT.
: LPT2 (LPT1, COM1, LPT2)
PR2_SND.
: PR2 (PR1, PR2, PR3, PR4,
PR5, PR6, PR7, PR8
PR2_WAIT.
: YES
PR2_IN.
: AUTO
(NONE, AUTO)
PR2_ORNT.
PR2_FORM.
Physical Port
Secondary Printer
157
7GE&gt;IBM, 7FR&gt;IBM, 7ND&gt;IBM, DEC&gt;IBM)
(NONE, POSTSCR, AUTO_PS)
Printer Language Translation
String After Print Job
Hex Dump Mode Enabled
(A4, LETTER, LEGAL, EXECUT)
PostScript Page Size
: PORTR
(PORTR, LANDS, R_PORTR, R_LANDS) PostScript Page Orientation
: 66 0 100 60 30 50
PostScript Page Format
(MPL, MPP, CPI, LPI, LM, TM)
:
PostScript Font
(Courier when not specified)
UNIX
---
Appendix B: The Parameter List
NetWare
AXIS 560/660 User’s Manual
OS/2
Windows
NetWare
158
Appendix B: The Parameter List
---
PRINTER3 MENU
PR3_OUT.
: COM1
PR2_SND.
PR2_WAIT.
: PR3 (PR1, PR2, PR3, PR4,
PR5, PR6, PR7, PR8
: YES
PR3_IN.
: AUTO
PR3_BEF.
:
PR3_STR.
:
PR3_CSET.
: NONE
PR3_FILT.
PR3_AFT.
PR3_DUMP.
PR3_SIZE.
PR3_ORNT.
PR3_FORM.
:
:
:
:
:
:
PR3_FONT.
:
NONE
Macintosh
PR4_SND.
(LPT1, COM1, LPT2)
Wait on Busy
Read Back Port
(Read-Back of information)
String Before Print Job
String Substitutions
(NONE, ISO&gt;IBM, 7UK&gt;IBM, 7SW&gt;IBM, Character Set Conversion
7GE&gt;IBM, 7FR&gt;IBM, 7ND&gt;IBM, DEC&gt;IBM)
(NONE, POSTSCR, AUTO_PS)
Printer Language Translation
(LPT1, COM1, LPT2)
PR4_WAIT.
PR4_IN.
: PR4 (PR1, PR2, PR3, PR4,
PR5, PR6, PR7, PR8
: YES
: AUTO
(NONE, AUTO)
PR4_BEF.
PR4_STR.
PR4_CSET.
:
:
: NONE
PR4_FILT.
PR4_AFT.
PR4_DUMP.
PR4_SIZE.
PR4_ORNT.
PR4_FORM.
:
:
:
:
:
:
PR4_FONT.
:
NONE
Physical Port
Secondary Printer
(NONE, AUTO)
NO
A4
(A4, LETTER, LEGAL, EXECUT)
PORTR
(PORTR, LANDS, R_PORTR, R_LANDS)
66 0 100 60 30 50
--- PRINTER4 MENU
PR4_OUT.
: COM1
UNIX
AXIS 560/660 User’s Manual
String After Print Job
Hex Dump Mode Enabled
PostScript Page Size
PostScript Page Orientation
PostScript Page Format
(MPL, MPP, CPI, LPI, LM, TM)
PostScript Font
(Courier when not specified)
Physical Port
Secondary Printer
Wait on Busy
Read Back Port
(Read-Back of information)
String Before Print Job
String Substitutions
(NONE, ISO&gt;IBM, 7UK&gt;IBM, 7SW&gt;IBM, Character Set Conversion
7GE&gt;IBM, 7FR&gt;IBM, 7ND&gt;IBM, DEC&gt;IBM)
(NONE, POSTSCR, AUTO_PS)
Printer Language Translation
NO
A4
(A4, LETTER, LEGAL, EXECUT)
PORTR
(PORTR, LANDS, R_PORTR, R_LANDS)
66 0 100 60 30 50
String After Print Job
Hex Dump Mode Enabled
PostScript Page Size
PostScript Page Orientation
PostScript Page Format
(MPL, MPP, CPI, LPI, LM, TM)
PostScript Font
(Courier when not specified)
PRINTER5 MENU
PR5_OUT.
: LPT1
PR5_SND.
PR5_WAIT.
: PR5 (PR1, PR2, PR3, PR4,
PR5, PR6, PR7, PR8
: YES
(LPT1, COM1, LPT2)
PR5_IN.
: AUTO
Physical Port
Secondary Printer
PR5_CSET.
Wait on Busy
Read Back Port
(Read-Back of information)
:
String Before Print Job
: 010A020D0A
String Substitutions
: NONE
(NONE, ISO&gt;IBM, 7UK&gt;IBM, 7SW&gt;IBM, Character Set Conversion
PR5_FILT.
PR5_AFT.
PR5_DUMP.
: NONE
:
: NO
PR5_SIZE.
PR5_ORNT.
PR5_FORM.
:
:
:
PR5_FONT.
:
(LPT1, COM1, LPT2)
: PR6 (PR1, PR2, PR3, PR4,
PR5, PR6, PR7, PR8
: YES
: AUTO
(NONE, AUTO)
Physical Port
Secondary Printer
PR6_BEF.
PR6_STR.
PR6_CSET.
Wait on Busy
Read Back Port
(Read-Back of information)
:
String Before Print Job
: 010A020D0A
String Substitutions
: NONE
(NONE, ISO&gt;IBM, 7UK&gt;IBM, 7SW&gt;IBM, Character Set Conversion
PR6_FILT.
PR6_AFT.
PR6_DUMP.
PR6_SIZE.
PR6_ORNT.
PR6_FORM.
:
:
:
:
:
:
PR6_FONT.
:
PR6_WAIT.
PR6_IN.
NONE
Windows
String After Print Job
Hex Dump Mode Enabled
A4
(A4, LETTER, LEGAL, EXECUT)
PostScript Page Size
PORTR
(PORTR, LANDS, R_PORTR, R_LANDS) PostScript Page Orientation
66 0 100 60 30 50
PostScript Page Format
(MPL, MPP, CPI, LPI, LM, TM)
PostScript Font
(Courier when not specified)
--- PRINTER6 MENU
PR6_OUT.
: LPT2
PR6_SND.
7GE&gt;IBM, 7FR&gt;IBM, 7ND&gt;IBM, DEC&gt;IBM)
(NONE, POSTSCR, AUTO_PS)
Printer Language Translation
OS/2
PR5_STR.
(NONE, AUTO)
Macintosh
PR5_BEF.
159
7GE&gt;IBM, 7FR&gt;IBM, 7ND&gt;IBM, DEC&gt;IBM)
(NONE, POSTSCR, AUTO_PS)
Printer Language Translation
NO
A4
(A4, LETTER, LEGAL, EXECUT)
PORTR
(PORTR, LANDS, R_PORTR, R_LANDS)
66 0 100 60 30 50
String After Print Job
Hex Dump Mode Enabled
PostScript Page Size
PostScript Page Orientation
PostScript Page Format
(MPL, MPP, CPI, LPI, LM, TM)
PostScript Font
(Courier when not specified)
UNIX
---
Appendix B: The Parameter List
NetWare
AXIS 560/660 User’s Manual
NetWare
160
Appendix B: The Parameter List
---
PRINTER7 MENU
PR7_OUT.
: COM1
PR7_SND.
PR7_WAIT.
: PR7 (PR1, PR2, PR3, PR4,
PR5, PR6, PR7, PR8
: YES
PR7_IN.
: AUTO
Windows
OS/2
Physical Port
Secondary Printer
PR7_CSET.
PR7_FILT.
PR7_AFT.
PR7_DUMP.
: NONE
:
: NO
PR7_SIZE.
PR7_ORNT.
PR7_FORM.
:
:
:
PR7_FONT.
:
PR7_STR.
Macintosh
(LPT1, COM1, LPT2)
Wait on Busy
Read Back Port
(Read-Back of information)
:
String Before Print Job
: 010A020D0A
String Substitutions
: NONE
(NONE, ISO&gt;IBM, 7UK&gt;IBM, 7SW&gt;IBM, Character Set Conversion
PR7_BEF.
UNIX
AXIS 560/660 User’s Manual
(NONE, AUTO)
7GE&gt;IBM, 7FR&gt;IBM, 7ND&gt;IBM, DEC&gt;IBM)
(NONE, POSTSCR, AUTO_PS)
Printer Language Translation
String After Print Job
Hex Dump Mode Enabled
A4
(A4, LETTER, LEGAL, EXECUT)
PostScript Page Size
PORTR
(PORTR, LANDS, R_PORTR, R_LANDS) PostScript Page Orientation
66 0 100 60 30 50
PostScript Page Format
(MPL, MPP, CPI, LPI, LM, TM)
PostScript Font
(Courier when not specified)
--- PRINTER8 MENU
PR8_OUT.
: COM1 (LPT1, COM1, LPT2)
PR8_SND.
: PR8 (PR1, PR2, PR3, PR4,
PR5, PR6, PR7, PR8
PR8_WAIT.
: YES
PR8_IN.
: AUTO
(NONE, AUTO)
Physical Port
Secondary Printer
PR8_BEF.
PR8_STR.
PR8_CSET.
Wait on Busy
Read Back Port
(Read-Back of information)
:
String Before Print Job
: 010A020D0A
String Substitutions
: NONE
(NONE, ISO&gt;IBM, 7UK&gt;IBM, 7SW&gt;IBM, Character Set Conversion
PR8_FILT.
PR8_AFT.
PR8_DUMP.
PR8_SIZE.
7GE&gt;IBM, 7FR&gt;IBM, 7ND&gt;IBM, DEC&gt;IBM)
: POSTSCR (NONE, POSTSCR, AUTO_PS)
:
: NO
: A4
(A4, LETTER, LEGAL, EXECUT)
PR8_ORNT.
PR8_FORM.
PR8_FONT.
Printer Language Translation
String After Print Job
Hex Dump Mode Enabled
PostScript Page Size
: PORTR
(PORTR, LANDS, R_PORTR, R_LANDS) PostScript Page Orientation
: 66 0 100 60 30 50
PostScript Page Format
(MPL, MPP, CPI, LPI, LM, TM)
:
PostScript Font
(Courier when not specified)
: 60
L1_MGM_INFO.
L1_COMMENT.
: AUTO
:
(DISABLE, AUTO)
--- COM1 Menu
C1_BAUDR.
: 9600 (300, 600, 1200, 2400, 4800, 9600,
19200, 38400, 57600, 115200)
C1_NBITS.
: 8
(7, 8)
C1_PARIT.
: NONE
(NONE, ODD, EVEN)
C1 STOPB.
: 2
(1, 2)
C1_HNDSH.
: ROBUST-BOTH (NONE, XON/XOFF, ROBUST,
RDY/BSY, BOTH, ROBUST-BOTH)
C1_READT.
: 3
C1_BSYTM.
: 60
C1_MGM_INFO.
C1_COMMENT.
: AUTO (DISABLE, AUTO)
:
--- LPT2 Menu
L2_CENTR.
: HISPEED (IBM_PC, STNDRD, FAST HISPEED)
L2_BSYTM.
: 60
L2_MGM_INFO.
L2_COMMENT.
: AUTO (DISABLE, AUTO)
:
Centronics Interface Timing LPT1
Busy Status Time-Out LPT1
(All status reporting disabled if set to 0)
Printer Management Information LPT1
Optional user comment describing the printer at LPT1
Baud Rate COM1
Word Length COM1
Parity COM1
Stop Bits COM1
Handshake Protocol COM1
Printer Feedback Delay COM1
Busy Status Time-Out COM1
(All status reporting disabled if set to 0)
Printer Management Information COM1
Optional user comment describing the printer at COM1
Centronics Interface Timing LPT2
Busy Status Time-Out LPT2
(All status reporting disabled if set to 0)
Printer Management Information LPT2
Optional user comment describing the printer at LPT2
OS/2
: HISPEED (IBM_PC, STNDRD, FAST, HISPEED)
L1_BSYTM.
Macintosh
L1_CENTR.
NetWare
--- LPT1 Menu
161
Windows
Appendix B: The Parameter List
UNIX
AXIS 560/660 User’s Manual
Appendix C: Technical Specifications
Supported Systems
Novell NetWare:
Microsoft LAN Manager:
OS/2
IBM LAN Server:
Microsoft Windows:
Macintosh
LANtastic
UNIX
AXIS 560/660 User’s Manual
Appendix C Technical Specifications
Windows
NetWare
162
BSD Systems:
System V Systems:
Versions 3.11, 3.12, 4.10 and above, supporting both NDS and Bindery
Emulation. A maximum of 16 bindery file servers and 96 print queues can be
served.
NDPS supported by versions 4.11 and above.
NetWare5 and Pure IP supported.
User messages are also supported.
Print Methods: RPRINTER/NPRINTER, PSERVER.
LAN Manager 2.0c and above, running under OS/2 ver 1.3 and above.
LAN Server 1.3 and above, running under OS/2 ver 1.3 and above including
OS/2 Warp, OS/2 Warp Connect.
Windows NT ver. 3.5 and above, Windows 2000, Windows for
Workgroups, Windows 95, Windows 98.
LANtastic 7.0, from any of the supported Windows clients, defined above.
All Operating Systems supporting the TCP/IP suite of protocols, including:
BSD 4.2, 4.3, 4.4, SunOS4 (Solaris 1.x), DEC Ultrix etc.
R3, R4, AT&amp;T, Interactive, SCO, SunOS5 (Solaris 2.x), HP-UX, IBM AIX,
Silicon Graphics IRIX, DEC Alpha OSF/1, BULL (BOS, AIX).
Other Systems:
IBM (MVS, VM, VSE, OS/400), DEC VMS, guidelines for other systems.
Print Methods:
LPD, FTP, PROS (named pipe &amp; filtered), Reverse Telnet, IPP.
Apple EtherTalk:
(AXIS 560 only) Print Method: AppleTalk Phase 2.
Netscape Navigator 3.0 and higher and MS Internet Explorer 3.0 and higher.
WWW:
Supported Protocols
NetWare:
Windows and OS/2:
LANtastic
TCP/IP:
Apple EtherTalk:
IPX, SAP, RIP, SPX, SNMP, NCP (extended with NDS), NLSP, DIAG,
TCP/IP.
NetBIOS/NetBEUI or TCP/IP, WINS.
NetBIOS/NetBEUI.
LPD, FTP, Telnet, Reverse Telnet, PROS, BOOTP, ARP, RARP, DHCP
ICMP, IP, TCP, UDP, HTTP, SNMP, TFTP, SLPv2, Dynamic DNS, IPP.
(AXIS 560 only) AARP, ATP, DDP, NBP, PAP, RTMP, ZIP.
Network Management
Appendix C: Technical Specifications
SNMP-MIB II compliant (over UDP/IP and IPX), host resource MIB
compliant (over UDP/IP and IPX), private enterprise MIB included. LAN
Network Manager for OS/2. Print server status in NWAdmin/PCONSOLE.
163
NetWare
AXIS 560/660 User’s Manual
AXIS 660
32 bit RISC Controller, 1 Mbyte Flash memory. 256 kbytes RAM.
32 bit RISC Controller, 1 Mbyte Flash memory. 576 kbytes RAM.
Logical Connection
AXIS 560
AXIS 660
Running simultaneously any combination of the supported protocols. Use of
IEEE802.2, IEEE802.3, SNAP and Ethernet II frame types simultaneously.
Running simultaneously any combination of the supported protocols. Use of
IEEE802.2 and IEEE802.5 (with Early Token release support for 16 Mbps),
frame types simultaneously
OS/2
AXIS 560
Windows
Hardware
AXIS 660
10baseT (Twisted Pair) and 10base2 (Thin wire) Ethernet
Media Type 1/DB9/STP and Media Type 3/RJ45/UTP. Support for 4 and
16 Mbps Token Ring networks
Security
UNIX:
NetWare:
Logical Printers
Root password. User access list and printer access.
Encrypted passwords.
The logical printer ports can be programmed to perform auto ASCII to
PostScript conversion, string before and after job, string substitution,
alternative output and character set conversion.
Parallel Printer
AXIS 560
AXIS 660
Two IEEE 1284 compliant high-speed parallel ports with 25-pin DSUB
connectors. Sustained throughput of up to 400 kbytes/s using NetWare. Bidirectional support for Apple, Reverse Telnet, PROS.
Two IEEE 1284 compliant high-speed parallel ports with 25-pin DSUB
connectors. Sustained throughput of up to 400 kbytes/s using NetWare. Bidirectional support for Reverse Telnet, PROS.
UNIX
AXIS 560
Macintosh
Attachments
164
Appendix C: Technical Specifications
UNIX
Macintosh
OS/2
Windows
NetWare
Serial Printer
Front Panel
AXIS 560/660 User’s Manual
One serial port, RS 232, 9-pin DSUB connector. XON/XOFF or RTS/CTS.
Data rates up to 115,200 baud.
2 LED indicators: Power and Network.
Test button for information printouts.
Slide switch for Token Ring speed (AXIS 660 only)
Dimensions
AXIS 560
AXIS 660
Weight
Environmental
Height x Width x Depth
1.0 x 7.0 x 4.7 inches (2.5 x 17.5 x 12.0 cm)
1.0 x 6.5 x 4.7 inches (2.5 x 16.2 x 12.0 cm)
0.86 lb. (0.39 kg)
Approvals
EMC:
Safety:
NetWare
Temperature: 40 - 105&deg; F (5 - 40&deg; C).
Humidity: 10 - 95% non-condensing.
OS/2
AXIS 660
EN 55022/1994, EN50082-1/1992. FCC Class A.
EN 60950.
Macintosh
AXIS 560
Power provided by external supply:
Maximum 3.24 W. (Type PS-B, 12V, 500 mA).
Maximum 3.72 W. (Type PS-B, 12V, 500 mA).
165
UNIX
Power Consumption
Appendix C: Technical Specifications
Windows
AXIS 560/660 User’s Manual
Windows
NetWare
166
Appendix D: Glossary
Appendix D Glossary
AIX
Advanced Interactive eXecutive. A version of the UNIX operating
system from IBM that runs on various IBM computers including
Mainframe systems.
ARP
Address Resolution Protocol. A protocol within the TCP/IP suite of
network protocols that allows a host to find the physical address of a
node on the same network. It is available in UNIX, Windows 95,
Windows 98 and Windows NT. ARP cannot be used across routers.
Macintosh
OS/2
BOOTP
BSD
config file
UNIX
AXIS 560/660 User’s Manual
BOOT Protocol. A TCP/IP protocol, used for downloading start-up
information such as the IP address to hosts on the network. It is only
available in UNIX. BOOTP requires a BOOTP daemon on your
system. A request made to an active BOOTP daemon initiates a search
of the Boot Table for an entry matching the print server's Ethernet
address. If a matching entry is found, the daemon downloads the IP
address to the print server.
Berkeley Software Distribution. The University of California,
Berkeley additions to the UNIX operating system.
This is a file that resides in the print server’s memory and contains all
the parameters that determine the AXIS 560/660 functionality. By
editing the config file (changing the parameter settings), you can
configure the AXIS 560/660 to meet the printing needs of your
network.
DNS
Domain Name Service. Reflects the server names and addresses within
a network.
Flash Memory
The print server software is stored in Flash Memory. This memory is
provided by a silicon chip that like any other ROM device, retains
data content even after power is removed. However, Flash Memory is
unique because it allows its data to be erased and re-written. This
means that you can install software updates for your server as soon as
they become available, without having to replace any parts. The new
software is simply loaded into the server over the network.
FTP
Hypertext Markup Language. A standard hypertext language used for
creating World Wide Web pages and other hypertext documents.
HTTP
Hypertext Transfer Protocol. The TCP/IP protocol for Web based
communication.
LED
NetWare
File Transfer Protocol. A TCP/IP protocol used for logging in to
network servers and for transferring files.
HTML
IP
Windows
To fully benefit from this method, the AXIS 560/660 also supports
the WINS host name resolution protocol, which is available in
Windows NT networks.
OS/2
Dynamic Host Configuration Protocol. DHCP is available in
Windows NT, NetWare 5 and UNIX systems, and allows for the
automatic but temporary assignment of IP addresses from a central
pool. DHCP causes the selected host to automatically allocate and
download an unused IP address to the requesting print server. It also
provides validation data that defines how long the IP addresses will
remain valid.
167
Internet Protocol. The TCP/IP session-layer protocol that regulates
packet forwarding by tracking IP addresses, routing outgoing messages
and recognizing incoming messages.
Light Emitting Diode.
UNIX
DHCP
Appendix D: Glossary
Macintosh
AXIS 560/660 User’s Manual
Appendix D: Glossary
UNIX
AXIS 560/660 User’s Manual
Logical Printer
A logical printer acts as a filter between the network and the physical
printer. It appears to the user as a normal printer with additional
characteristics. For example a UNIX workstation may only send a line
feed (LF) to a shared printer that needs carriage return (CR) and LF.
The logical printer can solve this problem by adding a CR.
MIB
Management Information Base. A database of network configuration
information used by SNMP and CMIP to monitor or change network
settings.
NCP
NetWare Core Protocol. Network clients use the NCP to request
services of servers, and servers use NCP to provide services, such as file
and print services.
NDS
NetWare Directory Services. A hierarchical data base that manages
NetWare network resources such as servers and volumes.
RARP
Reverse Address Resolution Protocol. A TCP/IP protocol used for
downloading IP addresses in UNIX networks. It requires a RARP
daemon on your system, and only operates within a single network
segment. A request made to an active RARP daemon initiates a search
of the Ethernet Address Table for an entry matching the print server's
Ethernet address. If a matching entry is found, the daemon downloads
the IP address to the print server.
RISC
Reduced Instruction Set Computing. A processor that recognizes only
a limited number of assembly-language instructions.
Macintosh
OS/2
Windows
NetWare
168
SAP
SNMP
TCP
Service Advertising Protocol. A NetWare network name advertising
service that e.g. file servers can use for advertising their existence to
network clients.
Simple Network Management Protocol. A TCP/IP protocol for
managing and monitoring nodes on a network.
Transmission Control Protocol. The connection-oriented, transportlevel protocol used in the TCP/IP suite of protocols.
A 32-bit multi-tasking, multi-user operating system originally
developed by AT&amp;T.
URL
Uniform Resource Locator. A way of specifying the location of
publicly available information on the Internet.
WINS
Windows Internet Name Service. A NetBIOS Name Server that maps
NetBIOS names to dynamically assigned IP addresses.
Wizard
A special form of user assistance that automates a task through a dialog
with the user. Wizards help the user to accomplish tasks that are
complex and require experience, and even for the experienced user can
help to speed up an operation.
NetWare
UNIX
Windows
Trivial File Transport Protocol. A simpler version of the FTP protocol
that is used by the print server for automatic downloading of config
files.
OS/2
TFTP
169
Macintosh
Appendix D: Glossary
UNIX
AXIS 560/660 User’s Manual
AXIS 560/660 User’s Manual
UNIX
Macintosh
OS/2
Windows
NetWare
170
Index
A
Account file 129, 130
ASCII to Postscript Conversion 104
axinstall 93
AXIS MIB 134
AXIS NetPilot 119
AXIS Print Monitor 68
AXIS Print System 56
AXIS Print Utility for OS/2 83
AXIS Print Utility for Windows 74
B
Basic setup
AXIS NetPilot 26
TCP/IP 30
Bi-directional Printing 107
C
Character Set Conversion 100
Chooser 86
config file 108, 153
Configuration methods
AXIS NetPilot
Parameter List Editor 120
Property pages 120
FTP 127
HP tools
HP JetAdmin 135
HP Web JetAdmin 135
NetWare Administrator 138
PCONSOLE 138
SNMP 133
Telnet 130
Web browser 109
Connectors 17
D
DDNS 32
Debugging Print Problems 107
E
Ethernet Address 30
F
Factory default settings 152
Flash memory 147
FTP 127
H
Hex Dump Mode 107
Host Name 32
HP JetAdmin 135
HP Web JetAdmin 135
I
Installation guide 24
Installation Summary 25
Internet Address 27
IPP 140
L
LANtastic 79
Logical Printers 98
M
Macintosh
O
OS/2
AXIS Print Utility for OS/2 83
Installing the print server 83
P
Parameter List 153
Physical Description
AXIS 660 17
Physical description 15
Power Indicator LED 18
Power indicator LED 16
Printer information 125
Printer port 15
Printing
parameter list 151
Test page 151
T
Test Button 17
Test button 16, 151
TFTP 34, 42
U
UNIX print methods 95
UNIX Printing methods
FTP 96
LPD 95
PROS A 96
PROS B 97
Windows
S
Setting the Internet address
ARP 35, 37
BOOTP 41
DHCP 34
RARP 39
Setting up
Macintosh 86
NetWare 43
OS/2 80
UNIX 92
Windows 54
SNMP 133
Status file 129, 132
String Functions 101
String Substitutions 102
Support services 4
OS/2
R
Ring Speed Switch 18
Macintosh
N
NDPS 44
NDS 48
NetWare
Advanced installation 47
Basic installation 26
NDPS 44, 140, 141, 142, 143
NetWare printing modes
Print Server Mode 53
Remote Printer Mode 53
Network connectors 15
Network Indicator LED 18
Network indicator LED 16
Pure IP 51
UNIX
Choosing a printer 87
Installing the print server 86
Setting the Internet address 90
NetWare
171
AXIS 560/660 User’s Manual
AXIS 560/660 User’s Manual
UNIX
Macintosh
OS/2
Windows
NetWare
172
Reverse Telnet 97
Upgrade Wizard 150
W
Windows 2000
Installing Printer Ports 62
Windows 3.1
AXIS Print Utility for Windows 74
Peer-to-peer printing 76
Windows 95
Installing printer ports 57
Windows 98
Installing printer ports 57
Windows for Workgroups
AXIS Print Utility for Windows 74
Client-server printing
Client setup 78
Server setup 77
Peer-to-peer printing 76
Windows NT 4.0
Installing Printer Ports 62
WINS 32, 34
">
Hello! I am an AI chatbot specifically trained to assist you with the Axis AXIS 660 User Manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!
Show related prompts
Assistant typing
Assistant terminated
Key features

Token Ring network
High speed (4 or 16 Mbps)
Three printer ports
Web-based management
Support for major computer systems
Easy installation
High performance
Reliable and efficient
Frequently asked questions

Connect the printer to one of the LPT1, LPT2, or COM1 ports using a suitable cable. Ensure the printer and power supply are off before connecting.
The AXIS 660 supports both shielded twisted pair (Media Type 1) and unshielded twisted pair (Media Type 3) cables. For 16 Mbps networks, screened or foiled Media Type 3 cabling is recommended.
Press and release the test button located on the AXIS 660. If the connection is successful, the AXIS 660 internal test page will be printed.