Welcome to the ACN First Aid tool.
Please remember that all the documents (including Quick
Installation guide and Manuals) are available on myacn.eu
under the Information Centre tab.
If your device does not
register please click here
If you are unable to make
or receive calls please
click here
For any other issues
please click here
If you have call quality
issues please click here
Registration Issues
Please confirm the ACN device that you are using:
Iris X Videophone
Grandstream HT 701
phone adaptor
Iris 5000 Videophone
Iris 3000 Videophone
Linksys SPA 2102 phone
adaptor
Start Again
IRIS X registration Issues
1
2
3
• Please make sure that the ethernet cable is connected to the NETWORK port on the back of
your ACN IRIS X Videophone and connect the other end to the first available port on your
modem/router. Also, please plug the power adaptor into the ACN IRIS X Videophone and to an
electrical outlet.
• Please go to Menu->System Settings->Network->Ethernet and make sure that “DHCP” option is
selected.
• Please turn off your modem/router and your Iris X Videophone and leave everything off for
approximately 1 minute. If you have a modem only, please leave it off for approx. 10 minutes.
Then, please power up the modem, wait 1 minute, power up the router and after an additional
minute, please power up the ACN Iris X Videophone. When you see the main screen of the
device, please check if it registers. - the telephone number in the main screen widget will be
green:
If your service was
recently reactivated
please click here
Still not registering!
My device is registering
Start Again
IRIS 5000 registration Issues
1
2
3
• Please make sure that the ethernet cable is connected to the WAN (blue) port on the back of
your ACN IRIS 5000 Videophone and connect the other end to the first available port on your
modem/router. Also, please plug the Power Adaptor into the ACN IRIS 5000 Videophone and
to an electrical outlet.
• Please go to Menu->Settings->Network->IP settings and make sure that in the field “Get IP”
the option “DHCP” is selected.
• Please turn off your modem/router and your Iris 5000 Videophone, leave everything off for
approximately 1 minute. If you have a modem only, please leave it off for approx. 10 minutes.
Then, please power up the modem, wait 1 minute, power up the router and after an
additional minute, please power up the ACN Iris 5000 Videophone and check if it
registers.(Please check if the upper left LED is lit)
If your service was
recently reactivated
please click here
Still not registering!
My device is registering
Start Again
IRIS 3000 registration Issues
1
2
3
• Please make sure that the ethernet cable is connected to the WAN (blue) port on the back of
your ACN IRIS 3000 Videophone and connect the other end to the first available port on your
modem/router. Also, please plug the Power Adaptor into the ACN IRIS 3000 Videophone and
to an electrical outlet.
• Please go to Menu->Settings->System Settings->Network->Interface and make sure that
“DHCP” is selected.
• Please turn off your modem/router and your Iris 3000 Videophone, leave everything off for
approximately 1 minute. If you have a modem only, please leave it off for approx. 10
minutes. Then, please power up the modem, wait 1 minute, power up the router and after
an additional minute, please power up the ACN Iris 3000 Videophone and check if it
registers. (Please check if the LED labelled Register is lit)
If your service was
recently reactivated
please click here
Still not registering!
My device is registering
Start Again
Grandstream HT 701 phone adaptor registration Issue
1
2
• Please make sure that the ethernet cable is connected to the ETHERNET port on the back
of your ACN Grandstream HT 701 phone adaptor and connect the other end to the first
available port on your modem/router. Also, please plug the power adaptor into the ACN
Grandstream HT 701 and to an electrical outlet.
• Please turn off your modem/router and your ACN Grandstream HT 701 phone adaptor,
leave everything off for approximately 1 minute. If you have a modem only, please leave
it off for approx. 10 minutes. Then, please power up the modem, wait 1 minute, power
up the router and after an additional minute, please power up the ACN Grandstream HT
701 phone adaptor and check if it registers
If your service was
recently reactivated
please click here
Still not registering!
My device is registering
Start Again
Linksys SPA 2102 phone adaptor registration issues
1
2
• Please make sure that the ethernet cable is connected to the Network port on the back
of your Linksys SPA 2102 phone adaptor and connect the other end to the first
available port on your modem/router. Also, please plug the power adaptor into the
Linksys SPA 2102 phone adaptor and to an electrical outlet.
• Please turn off your Modem/Router and your Linksys SPA 2102 phone adaptor, leave
everything off for approximately 1 minute. If you have a modem only, please leave it
off for approx. 10 minutes. Then, please power up the modem, wait 1 minute, power
up the router and after an additional minute, please power up the Linksys SPA 2102
phone adaptor and check if it registers.
If your service was
recently reactivated
please click here
Still not registering!
My device is registering
Start Again
Oops!!... This didn’t solve the issue.
Please prepare the following information:
- Account number and/or telephone number
- MAC Address (can be found on the sticker at the bottom of the device)
- Modem/Router brand and model
- Internet service provider name
And contact our dedicated Customer Services department via online Chat, by
completing a contact form 24/7 here or on the telephone: (+44) 020 360 85 051
(09:00-17:00, Monday – Friday)
Start Again
Thank you for using the ACN troubleshoot tool!
If you have further queries, please don’t hesitate to contact our
dedicated Customer Services department via online Chat, or by
completing a contact form 24/7 here or on the telephone:
(+44) 020 360 85 051 (09:00-17:00, Monday – Friday)
Start Again
IRIS 3000 registration Issues
1
2
3
4
5
• Make sure your Iris 3000 is powered on and correctly connected to your network
• Please press Menu->Settings->System Settings->Factory Reset
• In Factory Reset box enter 7517517
• Press Down Key to highlight “Start Factory Reset” and press OK (Note: if 7517517 code is not
accepted, please try again and leave the edit box empty)
• Press OK for “Yes” and wait for Iris 3000 to restart completely.
Still not registering!
My device is registering
Start Again
IRIS 5000 registration Issues
1
2
3
4
5
• Make sure your Iris 5000 is powered on and correctly connected to your network
• Please press Menu->Settings->Admin Settings and press OK
• Enter password: 520827 (in some cases may have to use 1234) and press Accept
• Select Factory Reset, enter password:520827 (in some cases you may have to use 1234) and
press Accept
• Press Yes, the phone will now reboot and reload its profile and software
Still not registering!
My device is registering
Start Again
IRIS X registration Issues
1
2
3
4
• Make sure your Iris X is powered on and correctly connected to your network
• Please press Menu->System Settings->Maintenance->Reboot
• Select the Factory Reset option and press OK
• The phone will reboot and perform a factory reset (Note: After factory reset, one or more
calibration operations are required before the phone’s main screen shows up. Please follow the
instructions on the screen to finish calibration before using the phone)
Still not registering!
My device is registering
Start Again
Linksys SPA 2102 registration Issues
1
• Make sure your Phone Adaptor is powered on and correctly connected to your network
2
• Press **** to activate the ATA IVR Menu (you will hear "Linksys configuration menu. Please
enter the option followed by the # (pound) key or hang up to exit")
3
• Enter 73738# using the keys on the phone handset (and press "send" or "call" if required by the
handset to send the command to the ATA).
4
6
• The ATA will request confirmation (you will hear “Press 1 to confirm, press * to exit”)
• Press 1 to confirm (you may hear either the full message "Option successful" or a
part of it it) and hang up.
Still not registering!
My device is registering
Start Again
Grandstream HT-701 registration Issues
1
2
3
4
5
6
• Make sure your Phone Adaptor is powered on and correctly connected to your network
• Locate the needle-sized hole on the back panel between the power connection and the
Ethernet port labelled "Reset"
• Insert a pin in this hole, and press for about 7-10 seconds until the device lights flash
• Take out the pin
• Wait 2-4 minutes while the device reloads its software and configuration
• Once the Power and the 4 Phone LEDs are solid, the device is ready to use
Still not registering!
My device is registering
Start Again
No Incoming/Outgoing Calls
Please confirm the ACN device that you are using:
Iris Videophone
Phone Adaptor
Start Again
No Incoming/Outgoing Calls
1
• Make sure your ACN Videophone is registered as per information from the Quick Installation Guide. If it’s not
registered, please click here
2
• If you hear a message, that „the line has been placed out of service” when calling out/receiving calls, please go
to your ACN Selfcare portal to see if you have an overdue and make a payment.
3
• Please confirm that the number you dialed is correct and you are using the necessary country code when calling
abroad. If you call in-country, there’s no need to use +44 country code.
4
• Please check if the number you wish to call is reachable from a different phone. If not, the problem may be
caused by the dialed party and not our service.
5
• Please note the details of the unsuccessful call (the message you hear, day and time of the call and the dialed
number). Please try to dial the number a few times during the day to rule out any temporary problems.
6
• If incoming calls are not possible, please confirm that you do nothave „do not disturb” option enabled by
entering *79 on the keypad and pressing Call Button
Escalate
Start Again
No Incoming/Outgoing Calls
1
• Make sure your ACN Phone Adaptor is registered as per information from the Quick Installation Guide. If it’s not
registered, please click here
2
• If you hear a message, that „the line has been placed out of service” when calling out/receiving calls, please go to
your ACN Selfcare portal to see if you have an overdue and make a payment.
3
• Please confirm that the number dialed is correct and you are using the necessary country code when calling
abroad. If you call in-country, there’s no need to use +44 country code.
4
• Please check if the number you wish to call is reachable from a different phone. If not, the problem may be
caused by the dialed party and not our service.
5
• Please note the details of the unsuccessful call (the message you hear, day and time of the call and the dialed
number). Please try to dial the number a few times during the day to rule out any temporary problems.
6
• If you are using Linksys SPA 2102 Adaptor, please confirm that the handset is connected to Phone 1 port and not
Phone 2 port.
7
• If your telephone uses BT Phone Plug and there’s no dial tone after picking up the handset, please click here for
further details
END
Start Again
Converter Instructions
•If you suspect that the problem may lie with the fact that the telephone is not fully
compatible with our device, here is a link to the converter that may allow your phone to work
with our Analogue Telephone Adaptor.
•“Broadbandbuyer US Plug to BT Socket Adapter w/Ring Capacitor - RJP/BTS”, cost £2.26 (incl.
VAT).
•http://www.broadbandbuyer.co.uk/Shop/ShopDetail.asp?ProductID=2370
•There are many well-known high street stores (e.g. http://www.maplin.co.uk/) that may
stock this device or something similar. We recommend that you follow the link above, print
off a copy of that webpage, and take a copy of the printout if you require assistance at the
store.
•Please ensure that you then use the original telephone cable that came with your telephone
when using the converter.
END
Start Again
Call Quality Issues
1
2
3
4
5
6
7
8
9
• When using the ACN Videophone, please confirm that the handset is connected to the proper port and the Volume is set to sufficient
level
• Before escalating, please perform a Speed Test to check your internet connection.
• Please navigate to the website http://www.speedtest.net and choose option ”Settings” in the right upper corner
• As the ”Preferred Server”, please choose ”Amsterdam [NL] Ookla” and click ”Save” button below.
• Click on ”Take A Speed Test” and when page reloads, please click on ”Begin Test Your Preferred Server”
• After the test is finished, please write down values for ”Ping”, ”Download Speed” and ”Upload Speed”.
• Please navigate to the website http://www.pingtest.net and click on ”Begin Test”.
• After the test is finished, please write down values for ”Packet Loss”, ”Ping” and ”Jitter”.
• Please write down time, day and description of at least three test calls during which the quality was affected
Escalate
Start Again
Before escalating, please also prepare the following information:
- Account number and/or telephone number
- MAC Address (can be found on the sticker at the bottom of the device)
- Modem/Router brand and model
- Internet service provider name
And contact our dedicated Customer Services department via online Chat, by
completing a contact form 24/7 here or on the telephone: (+44) 020 360 85 051
(09:00-17:00, Monday – Friday)
Start Again
Other Issues
1
2
3
• If your device is not powering up, please confirm that there is electricity in the socket by connecting a
different device and if applicable, please try using a different power supply from the same type of
device. Please do not use a supply from another type of device as it may damage the equipment.
• If you are experiencing operational issues (freezing up, general slowness) with the device, please press
here to proceed with the factory reset.
• If your device shows a message about memory running low, please reboot the device, which should fix
the problem.
Escalate
Start Again
Factory Reset
Please confirm the ACN device that you are using:
Iris X Videophone
Grandstream HT 701
phone adaptor
Iris 5000 Videophone
Iris 3000 Videophone
Linksys SPA 2102 phone
adaptor
Start Again