Vermont Castings 360DVSR Operating instructions

Multisided Top/Rear Vent
Convertible Direct Vent
Fireplaces:
360DVS2
360DVS3
360DVSL
360DVSR
INSTALLER/CONSUMER
SAFETY INFORMATION
PLEASE READ THIS MANUAL
BEFORE INSTALLING AND USING
APPLIANCE
IMPORTANT: Read all instructions
and warnings carefully before
starting installation. Failure to follow
these instructions may result in a
possible fire hazard, and will void the
warranty.
WARNING: If the information in this
manual is not followed exactly, a fire or
explosion may result, causing property
damage, personal injury, or loss of life.
FOR YOUR SAFETY:
• Installation and service must be performed by a qualified installer, service
agency, or
the gas supplier.
• Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
If you smell gas:
1. Open windows
2. Do not touch electrical switches.
3. Do not try to light any appliance.
4. Extinguish any open flame.
5. Do not use any telephone in your
building.
6. Immediately call your gas supplier
from a neighbor’s phone.
7. Follow your gas supplier’s
instructions.
8. If you cannot reach your gas supplier,
call the fire department.
Homeowner’s Installation
and Operating Manual
DE S I GN
CE
� � �� � � � � �
RTIFI E D
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
10006326 6/06 Rev. 1
360DVS Series Direct Vent Fireplaces
Installation & Operating Instructions
This gas appliance should be installed by a qualified installer in
accordance with local building codes and current CSA-B149.1
Installation Codes for Gas Burning Appliances and Equipment.
If the unit is being installed in a mobile home, the installation should
comply with the current CAN/CSA Z 240.4 code. For U.S.A. Installations, follow local codes and/or the current National Fuel Gas
Code, ANSI Z223.1/NFPA 54.
In the Commonwealth of Massachusetts, all gas fittings
and installation of this appliance shall be done by a
licensed gas fitter or licensed plumber.
FOR SAFE INSTALLATION AND OPERATION PLEASE
NOTE THE FOLLOWING:
1. This fireplace gives off high temperatures and should be
located out of high traffic areas and away from furniture and
draperies.
2. Children and adults should be alerted to the hazards of
high surface temperatures of this fireplace and should stay
away to avoid burns or ignition of clothing.
3. CAUTION: Due to high glass surface temperature, children should be carefully supervised when in the same
room as fireplace.
4. Under no circumstances should this fireplace be modified.
Parts removed for servicing should be replaced prior to
operating this fireplace again.
5. Installation and any repairs to this fireplace must be performed by a qualified installer, service agency or gas supplier. A professional service person should be contacted to
inspect this fireplace annually. Make it a practice to have
all of your gas fireplaces checked annually. More frequent
cleaning may be required due to excess lint and dust from
carpeting, bedding material, etc.
6. Control compartments, burners and air passages in this
fireplace should be kept clean and free of dust and lint.
Make sure the gas valve and pilot light are turned off before you attempt to clean this fireplace.
7. The venting system (chimney) of this fireplace should be
checked at least once a year, and if needed, your venting
system should be cleaned.
8. Keep the area around your fireplace clear of combustible
materials, gasoline and other flammable vapor and liquids.
This fireplace should not be used as a drying rack for
clothing, nor should Christmas stockings or decorations be
hung on or around the fireplace.
9. Under no circumstances should any solid fuels (wood, coal,
paper or cardboard, etc.) be used in this fireplace.
10. The flow of combustion and ventilation air must not be
obstructed in any way.
11. When the fireplace is installed directly on carpeting, vinyl
tile, or any combustible material other than wood, it must
be installed on a metal or wood panel extending the full
width and depth of the fireplace.
12. This fireplace requires adequate ventilation and combustion air to operate properly.
13. This fireplace must not be connected to a chimney flue serving
a separate solid fuel-burning fireplace.
14. When the fireplace is not in use, it is recommended the
gas valve be left in the “OFF” position.
10006326
This appliance may be installed in an aftermarket, permanently located, manufactured home, or mobile home
where not prohibited by local codes.
This appliance is only for use with type of gas
indicated on the rating plate. This appliance is not
convertible for use with other gases, unless a certified
kit is used.
IMPORTANT:
PLEASE REVIEW THE FOLLOWING CAREFULLY
Remove any plastic from trim parts before turning the
fireplace ON.
It is normal for fireplaces fabricated of steel to give off
some expansion and/or contraction noises during the
start up or cool down cycle. Similar noises are found
with your furnace heat exchanger or car engine.
It is not unusual for your gas fireplace to give off some
odor the first time it is burned. This is due to the curing of
the paint and any undetected oil from the manufacturing
process.
Please ensure that your room is well ventilated
- open all windows.
It is recommended that you burn your fireplace for
at least ten (10) hours the first time you use it. If the
optional fan kit has been installed, place the fan switch
in the “OFF” position during this time.
Proposition 65 Warning: Fuels used in gas, woodburning or oil fired appliances, and the products of
combustion of such fuels, contain chemicals known
to the State of California to cause cancer, birth defects and other reproductive harm.
California Health & Safety Code Sec. 25249.6
Locating Your Fireplace
X
X
X
Y
A
B
Y
Z
A
Y
LU584-2
Fig. 1 LocatingLU584-2
your gas fireplace
A Wall Location
(Fig. 1)
360DVS
Y (Minimumlocate
distancefireplace
between a glass panel and a
parallel wall) = 3’ (914mm)
Z (Minimum distance between edge of a glass panel
and an adjacent wall) = 3” (76mm)
B Island Location (Fig. 1)
X (Maximum length of horizontal venting) = 20’ (6.1m)
Refer to the venting section in this manual for specific dimensions.
3
360 DVS Series Direct Vent Fireplaces
Fireplace Dimensions - 360DVS2
I
Rear Vent Configuration
J
J
K
H
H
K
B
G
E
A
E
A
D
Electrical
Access
Electrical
Access
J
J
K
Gas Line
Access
J
Gas Line
Access
F
C
J
Top Vent Configuration
6326
360DVS2
rear vent
specs
H
J
K
J
K
H
K
B
G
C
I
E
A
E
A
D
Electrical
Access
Electrical
Access
J
K
J
F
Fig. 2a Fireplace specifications—360DVS2
Ref.
4
Gas Line
Access
J
Gas Line
Access
K
J
6326
360DVS2
Appliance
top vent Dimensions
specs
Rear Vent Configuration
Top Vent Configuration
A
38¹⁄₈”
(968 mm)
38¹⁄₈”
(968 mm)
B
43¹⁄₄”
(1099 mm)
43¹⁄₄”
(1099 mm)
C
D
E
F
G
H
I
J
K
24”
24”
37³⁄₈”
35⁷⁄₈”
30¹⁄₂”
12”
3¹⁄₈”
2³⁄₄”
1¹⁄₄”
(610 mm)
(610 mm)
(949 mm)
(911 mm)
(775 mm)
(305 mm)
(80 mm)
(70 mm)
(33 mm)
24”
24”
37³⁄₈”
35⁷⁄₈”
7”
12”
3¹⁄₈”
2³⁄₄”
1¹⁄₄”
(610 mm)
(610 mm)
(949 mm)
(911 mm)
(178 mm)
(305 mm)
(80 mm)
(70 mm)
(33 mm)
10006326
360DVS Series Direct Vent Fireplaces
Fireplace Dimensions - 360DVS3 / 306DVSL / 360DVSR
K
Rear Vent Configuration
I
J
H
H
B
K
ROD
A
E
G
D
Electrical
Access
J
Gas Line
Access
J
K
C
K
Top Vent Configuration
H
I
J
C
F
B
6326
360DVS3
rear vent
specs
H
K
B
G
A
E
Electrical
Access
J
K
D
Gas Line
Access
J
B
F
C
6326
Fig. 2b Fireplace specifications—360DVS3/ 360DDVSL/ 360DVSR
360DVS3
top vent
Ref.
A
B
C
D
E
F
G
H
I
J
K
10006326
specs Dimensions
Appliance
Rear Vent Configuration
38¹⁄₈”
(968 mm)
40⁵⁄₈”
(1032 mm)
24”
(610 mm)
24”
(610 mm)
37³⁄₈”
(949 mm)
35⁷⁄₈”
(911 mm)
30¹⁄₂”
(775 mm)
12”
(305 mm)
3¹⁄₈”
(80 mm)
2³⁄₄”
(70 mm)
1¹⁄₄”
(33 mm)
Top Vent Configuration
38¹⁄₈”
(968 mm)
40⁵⁄₈”
(1032 mm)
24”
(610 mm)
24”
(610 mm)
37³⁄₈”
(949 mm)
35⁷⁄₈”
(911 mm)
7”
(178 mm)
12”
(305 mm)
3¹⁄₈”
(80 mm)
2³⁄₄”
(70 mm)
1¹⁄₄”
(33 mm)
5
360 DVS Series Direct Vent Fireplaces
Framing Dimensions - 360DVS2
Rear Vent
Configuration
ROD
ROH
CFM121
ROW
Top Vent
Configuration
ROD
CFM121
360DVS2 REAR VENT CONFIGURATION
8/10/00
ROH
ROW
CFM122
Fig. 3a Fireplace framing dimensions—360DVS2
Ref.
ROD
ROH
ROW
6
CFM122
360DVS2
- TOP VENT
CONFIGURATION
Framing
Dimensions
8/10/00
Rear Vent Configuration
Top Vent Configuration
24” (610 mm) minus two times finishing material thickness to be even with face of unit.
38⁵⁄₈” (981 mm)
Not to be framed until unit is set in place,
due to 3¹⁄₈” (79 mm) allowance for flue collar
Not to be framed until unit is set in place
43³⁄₄” (1111 mm)
due to 3¹⁄₈” (79 mm) allowance for flue collar
10006326
360DVS Series Direct Vent Fireplaces
Framing Dimensions - 360DVS3 / 360DVSL / 360DVSR
Rear Vent Confiration
ROD
ROW
ROH
ROH
360DVSL
ROD
CFM123_360DVS3_dims_RV2
REAR VENT CONFIGURATION
8/10/00
rev. 8-23-02 rjs
ROW
360DVSR
ROD
360DVS/3/L/R
CFM123
ROD
ROH
ROH
ROH
360DVSL
ROH
360DVS3
360DVS/3/L/R
Top Vent Configuration
ROD
ROD
360DVS3
360DVSR
CFM124
Fig. 3b Fireplace framing dimensions—360DVS3/ 360DVSL/
360DVSR
CFM124_360DVS3_TV2
TOP VENT CONFIGURATION
Ref.
Model
ROD
ROH
ROW
8/10/00
Framing
Dimensions
rev. 8-23-02 rjs
Rear Vent Configuration
360DVS3
360DVSL/R
(See Note 1)
(See Note 2)
38⁵⁄₈” (981 mm)
Top Vent Configuration
360DVS3
360DVSL/R
(See Note 1)
(See Note 2)
Not to be framed until unit is set in place, due
to 3¹⁄₈” (79 mm) allowance for flue collar
40⁵⁄₈” (1032 mm) minus one time (1x) finishing material thickness to be even with face of unit.
NOTE 1: 24” (610 mm) minus two times (2x) finishing material thickness to be even with face of unit.
NOTE 2: 24³⁄₄” (629 mm) minus one time (1x) finishing material thickness to be even with face of unit.
10006326
7
360 DVS Series Direct Vent Fireplaces
Clearance to Combustibles
Appliance
Top .........................................0” (0 mm) to standoff
Bottom ..................................................... 0” (0 mm)
Vent End ....................... 1/2” (13 mm) to rear panel
Nonvent End (DVS2) .............................. 0” (0 mm)
Venting
Concentric sections of DV Vent:
Top, bottom & sides .............................. 1” (25 mm)
Nonconcentric sections of DV Vent:
Side and bottom .................................... 1” (25 mm)
Top ........................................................ 2” (51 mm)
Top View
J
The height at which a combustible mantel is fitted
above the fireplace is dependent on the depth of the
mantel. This also applies to the distance between the
mantel leg (if so fitted) and the fireplace. For correct
mounting height and width, refer to Fig. 4a and 4b and
the Mantel Chart below.
H
Mantel Leg
G
F
CFM197
Front View
Mantels
I
M
N
O
CFM197
Side
of Combustion
Mantel Corner Leg
Chart
04/16/02 sta Chamber
K
L
Mantel
Leg
The fitting of a bay window trim kit does not affect the
distances and reference points referred to in the diagram and chart.
Noncombustible mantels and legs may be installed at
any height and width around the appliance.
When using paint or lacquer to finish the mantel, such
paint or lacquer must be heat resistant to prevent discoloration.
V
W
X
Y
Z
CFM170
Ref.
F
G
H
I
J
Mantel
CFM170
Leg Depth
Ref.
DV Builder
Front
View
10” (254 mm)
K
8” (203 mm)
L
6” (152 mm)
M
4” (102 mm)
N
2” (51 mm)
O
Mantel Leg From Side
of Comb. Opening
11¹⁄₂” (292 mm)
9¹⁄₂” (241 mm)
7¹⁄₂” (191 mm)
5¹⁄₂” (140 mm)
3¹⁄₂” (89 mm)
Fig. 4b Combustible mantel leg minimum installation.
A
B
C
D
Hearth
E
Fireplace
Louvre Assembly
Top
Top of Combustion
Chamber
Bottom of Door Trim
Ref.
V
W
X
Y
Z
CFM146
Mantel Chart
Mantel ShelfCFM146
Mantel from Top
DV Mantel Chart
7/5/01 sta
or Breast Plate
Ref. of Comb. Chamber
10” (254 mm)
A
19” (483 mm)
8” (203 mm)
B
17” (432 mm)
6” (152 mm)
C
15” (381 mm)
4” (102 mm)
D
13” (330 mm)
2” (51 mm)
E
11” (297 mm)
A hearth is not mandatory; however, for aesthetic
purposes, we recommend installing a noncombustible
hearth that projects out 12” (305mm) or more from the
front of the fireplace.
Cold climate installation recommendation:
When installing this unit against a noninsulated exterior wall or chase, it is mandatory
the outer walls be insulated to conform to
applicable insulation codes.
Fig. 4a Combustible mantel minimum installation.
8
10006326
360DVS Series Direct Vent Fireplaces
Gas Inlet & Manifold Pressures
Framing & Finishing
1. Choose the unit location.
2. Place the unit into position and secure it to the floor
with 1¹⁄₂” (38mm) screws or nails. Holes to secure
the unit to the floor are located behind the access
door grille on the left and right sides of the unit.
3. Frame in the fireplace with a header across the top.
It is important to allow for the finished wall face when
setting the depth of the frame.
4. Drywall (sheetrock) or wood material may be placed
with a zero clearance to the top edges of the appliance when finishing walls above sides of the appliance with glass windows. NOTE: Attach wall finishing to constructed frame, not the appliance.
5. On 360DVSL and 360DVSR, drywall, wood, or wood
molding may be placed with zero clearance to the
rear wall of the unit, along the vertical edge formed
by the standoffs, to intersection of the rear wall, to
the side wall having the small glass window. NOTE:
Attach wall finishing to constructed frame, not
the appliance.
Final Finishing
Noncombustible materials such as brick or tile may be
extended over the edges of the face of the appliance.
DO NOT cover any vent or grille panels.
If a Trim Kit is going to be installed on the fireplace, the
brick or tile will have to be installed flush with the edges
of the appliance.
Gas Specifications
Model
360DVS2RN
360DVS2RP
360DVS2EN
360DVS2EP
360DVS3RN
360DVS3RP
360DVS3EN
360DVS3EP
360DVSLRN
360DVSLRP
360DVSLEN
360DVSLEP
360DVSRRN
360DVSRRP
360DVSREN
360DVSREP
Fuel
Nat
Prop
Nat
Prop
Nat
Prop
Nat
Prop
Nat
Prop
Nat
Prop
Nat
Prop
Nat
Prop
Gas Control
Millivolt
Millivolt
24V Hi/Lo
24V Hi/Lo
Millivolt
Millivolt
24V Hi/Lo
24V Hi/Lo
Millivolt
Millivolt
24V Hi/Lo
24V Hi/Lo
Millivolt
Millivolt
24V Hi/Lo
24V Hi/Lo
Max.
Input
BTU/h
38,000
38,000
38,000
38,000
38,000
38,000
38,000
38,000
38,000
38,000
38,000
38,000
38,000
38,000
38,000
38,000
Max.
Input
BTU/h
26,600
28,500
26,600
28,500
26,600
28,500
26,600
28,500
26,600
28,500
26,600
28,500
26,600
28,500
26,600
28,500
Natural
Inlet Minimum
Inlet Maximum
Manifold Pressure
LP (Propane)
4.5” w.c.
14.0” w.c.
3.5” w.c.
11.0” w.c.
14.0” w.c.
10.0” w.c.
Input ratings are shown in BTU per hour and are
certified without deration for elevations up to
4,500 feet (1,370 m) above sea level.
For elevations above 4,500 feet (1,370 m) in USA,
installations must be in accordance with the
current ANSI Z223.1/NFPA 54 and/or local codes
having jurisdiction.
In Canada, please consult provincial and/or local
authorities having jurisdiction for installations
above 4,500 feet (1,370 m).
360DVS2/ 360DVS3/ 360DVSL/ 360DVSR
CERTIFIED TO
ANSI Z21.88-2005 / CSA 2.33-2005
Vented Gas Fireplace Heaters
Gas Line Installation
When purging the gas lines, the window
frame assembly must be removed.
The gas pipeline can be brought in through the vent
end of the fireplace as well as the bottom. Knockouts
(to allow gas pipe installation and testing any gas connection) are provided on the bottom behind the valve.
It is most convenient to bring the gas line in from the
vent end of the valve, as this allows fan installation or
removal without disconnecting the gas line.
The gas line connection can be made with properly
tinned 3/8” copper tubing, 3/8” rigid pipe, or an approved flex connector. Since some municipalities have
additional local codes, it is always best to consult your
local authority and the CSA-B149.1 installation codes.
For USA installations, consult the current National Fuel
Gas Code, ANSI Z223.1/NFPA 54.
Always check for gas leaks with a mild
soap and water solution. Do not use an
open flame for leak testing.
1/2” Gas Supply
1/2” NPT X 1/2” Flare Shut-Off Valve
3/8” Flex Line
(From Valve)
FP297a
Fig. 5 Gas shutoff valve and flex connector.
9
10006326
FP297A
INSTA VENT FREE
UVHB26 GAS SUPPLY
7/1/98
360 DVS Series Direct Vent Fireplaces
The gas control is equipped with a captured-screw type
pressure test point, therefore it is not necessary to provide a 1/8” test point upstream of the control.
When using copper or flex connector, use only approved fittings. Always provide a union when using
black iron pipe so that the gas line can be easily disconnected for burner or fan servicing. Refer to the gas
specification for pressure details and ratings.
Electrical
Inlet Hole
Isolate or disconnect this or any other gas
appliance control from the gas line when
pressure testing.
Gas Inlet
Hole
DO NOT subject the fireplace valve to test
pressures exceeding 1/2 psi.
EB-1 Electrical Junction Box Connection
The fireplace, when installed, must be
electrically connected and grounded in accordance with local codes; in the absence
of local codes, use the current CSA C22.1
Canadian Electrical Code.
For USA installations, follow the local
codes and National Electrical Code ANSI/
NFPA No. 70.
It is strongly suggested the wiring of the
EB-1 Electrical Junction Box be carried out
by a licensed electrician.
Ensure power to the supply line has been
disconnected before commencing with this
procedure.
The EB-1 electrical junction box has been supplied
standard on this model to allow for easy connection of
the optional fan kits. (Fig. 6)
EB-1 Electrical box Depending on the specific model,
this box may be installed on
either side of the appliance.
FP1428
Fig. 6 EB-1 attachment.
Remote ON/OFF
Switch Installation
FP1428
location ON/OFF wall switch
Do not wireEB-1
the remote
for this gas appliance into a 120V power
supply.
1. Thread the wiring through the holes on the end
panels of the appliance. Take care not to cut the wire
or insulation on metal edges. Route the wire to a
conveniently located receptacle box.
2. Attach the wire to the ON/OFF switch and install the
switch into the receptacle box.
3. Connect the other ends of the wire to the gas control
valve, as shown in Figure 7.
Remote ON/OFF Switch
To connect the EB-1 box to the house electrical supply
follow the steps below.
1. Remove the front cover of the EB-1 box.
2. Remove the plug socket assembly from the EB-1
box.
3. Feed the supply line in from the out through the electrical knockout.
4. Connect the ground wire of the supply line to the
green screw of the socket assembly.
5. Connect the white wire of the power line to the
chrome screw of the socket assembly.
6. Connect the black wire of the power supply line to
the brass screw (polarized) of the socket assembly.
7. Refit the socket assembly back into the electrical
box and replace the cover plate.
8. The EB-1 electrical junction box is now ready to supply power to the FK12 or FK24 fan kit, if used.
10
TP
TH
Gas
Control
Valve
TP
TH
FP1429
Fig. 7 Remote switch wiring diagram for R models.
Alternate Switch Location
The remote switch can be installed on the front or the
side of the access door. Simply mount the switch to the
FP1429
bracket provided and screw the
bracket to either side
remote
wiring
of the frame, lining up the screws
withswitch
the prepunched
7/05
holes. (Fig. 8)
10006326
360DVS Series Direct Vent Fireplaces
Remove These Screws
Remove
These
Screws
FP1430
Fig. 8 Alternate switch location.
Optional Top Vent Application
This appliance is shipped as a rear vent unit. If the
installation layout requires the unit to be a top vent configuration, the appliance can be converted by following
the steps below.
Outer Collar Adapter
FP1431
Fig. 9 Remove screws from outer collar adapter.
FP1431
Insulation Pad
top
(Must
bevent
removed)
When removing and refitting the plates and
adapter, be sure the associated gasket is
undamaged and refitted as required.
1. Remove the ten (10) screws securing the outer collar adapter to the fireplace body. (Fig. 9)
2. Set the collar aside, complete with the gasket.
NOTE: Do not damage the gasket, as the adapter
and gasket must be refitted.
3. Remove the insulation material (exposed in Step
2) from the top of the unit. (Fig. 10) This material
can be discarded; however, if the unit is converted
back to rear-vent, a new piece of insulation material
approved by CFM Corporation must be used for this
purpose.
NOTE: When converting appliance to top vent,
ensure the insulation material referred to in step 3 is
completely removed.
4. Remove the 4 screws securing the flue cover plate
to the top of the intake box and remove the cover
and gasket. (Fig. 11)
5. Remove 4 screws securing the flue pipe to back of
the intake box and remove pipe and gasket. (Fig. 11)
6. Secure the plate and gasket removed in step 4 over
the flue opening in the back of the intake box. Ensure the gasket is in place and undamaged.
7. Install the flue pipe and gasket removed in step 5
over the flue opening in the top of the intake box.
8. Refit the outer collar adapter and gasket to the unit
with the round collar on the top. Secure the adapter
with the 10 screws removed in step 1.
remove screws
Flue
Pipe
FP1432
Fig. 10 Remove flue cover and pipe.
Flue
Cover
FP1432
Plate
remove flue cover
and pipe
Flue
Pipe
FP1433
Fig. 11 Flue pipe removal.
11
10006326
FP1433
flue cover plate
360 DVS Series Direct Vent Fireplaces
Electronic Gas Control Valve
This appliance may be fitted with a Honeywell ignition
module.
Installation of the remote ON/OFF starter switch on
electronic ignition units (Fig. 12):
1. Thread the wiring through the holes on the side
panels of the appliance. Take care not to cut the wire
or insulation on metal edges. Route the wire to a
conveniently located receptacle box.
2. Attach the wire to the ON/OFF switch and install the
switch into the receptacle box.
3. Connect the white wire from the wall switch to the
black wire from the transformer, using an approved
wire nut. Connect the black wire from the wall switch
to the black wire running from the #6 position of the
ignition module, also using an approved wire nut.
PILOT
HONEYWELL IGNITION MODULE
MV
MV/VP PV
1
2
3
24V
GRD
24V
5
6
SENSE SPARK
8
GREEN
RED
ORANGE
9
BLACK
ORANGE
LO
HI
NOVA SIT 822 VALVE
BLUE
WHITE
POWER CORD
W/FEMALE SPADE
24 VAC HOT
120 VAC RTN
WHITE
BLACK
BLACK
YELLOW
BLACK
OFF
WHITE
GREEN
24 VAC RET
120 VAC HOT
40VA TRANSFORMER
WALL SWITCH
BLACK
WHITE
FP1225
Fig. 12 Honeywell ignition module.
General Venting
Your fireplace is approved to be vented either through
the side wall, or vertically through the roof.
garden shed, fencing, deck or utility building within 24”
(610mm) from the front of the termination hood.
• Only CFM Corporation venting components, specifi-
Do not locate the termination hood where excessive
snow or ice buildup may occur. Be sure to check the
vent termination area after snow falls; clear it to prevent
accidental blockage of the venting system. When using
a snow blower, make sure snow is not directed toward
the vent termination area.
Location of Vent Termination
•
•
cally approved and labeled for this fireplace, may be
used.
Venting terminals shall not be recessed into a wall or
siding.
Horizontal venting must be installed on a level plane
without an inclining or declining slope.
There must not be any obstruction such as bushes,
12
It is imperative the vent termination be located observing minimum clearances as shown on the following
page.
10006326
360DVS Series Direct Vent Fireplaces
General Venting Information - Termination Location
INSIDE
CORNER DETAIL
V
D
H
A
V
N
N
E
L
V
B
V
F
C
B
Fixed
Closed
B
V
Ope
rab
Operable
le
V
B
CFM145a
G
V VENT TERMINATION
B
V
Fixed
Closed
V
J
G
X
B
I
A
X AIR SUPPLY INLET
M
V
K
X
G
A
V
V
AREA WHERE TERMINAL IS NOT PERMITTED
Canadian Installations1
CFM145a
(30cm)
DV Termin Location
5/01/01 Rev. 12/05/01
sta
US Installations2
A = Clearance above grade, veranda, porch,
deck, or balcony
B = Clearance to window or door that may be
opened
12”
C = Clearance to permanently closed window
12” (305mm) recommended to
prevent window condensation
6” (15cm) for appliances
< 10,000 Btuh (3kW), 9”
(23cm) for appliances > 10,000
Btuh (3kW) and < 50,000 Btuh
(15kW), 12” (30cm) for
appliances > 50,000 Btuh (15kW)
12” (305mm) recommended to
prevent window condensation
18” (458mm)
18” (458mm)
12” (305mm)
see next page
see next page
3’ (91cm) within a height of 15’ (5m)
above the meter/regulator assembly
12” (305mm)
see next page
see next page
3’ (91cm) within a height of 15’
(5m) above the meter/regulator
assy
3’ (91cm)
6” (15cm) for appliances
< 10,000 Btuh (3kW), 9”
(23cm) for appliances > 10,000
Btuh (3kW) and < 50,000 Btuh
(15kW), 12” (30cm) for
appliances > 50,000 Btuh (15kW)
3’ (91cm) above if within 10
feet (3m) horizontally
7’ (2.13m)†
D = Vertical clearance to ventilated soffit located
above the terminal within a horizontal
distance of 2’ (610mm) from the center
line of the terminal
E = Clearance to unventilated soffit
F = Clearance to outside corner
G = Clearance to inside corner (see next page)
H = Clearance to each inside of center line
extended above meter/regulator assembly
6” (15cm) for appliances
< 10,000Btuh (3kW), 12” (30cm)
for appliances > 10,000 Btuh (3kW) and
< 100,000 Btuh (30kW), 36” (91cm)
for appliances > 100,000 Btuh (30kW)
I = Clearance to service regulator vent outlet
J = Clearance to nonmechanical air supply inlet
to building or the combustion air inlet to any
other appliances
3’ (91cm)
6” (15cm) for appliances < 10,000
Btuh (3kW), 12” (30cm) for
appliances > 10,000 Btuh (3kW) and
< 100,000 Btuh (30kW), 36” (91cm)
for appliances > 100,000 Btuh (30kW)
K = Clearance to a mechanical air supply inlet
6’ (1.83m)
12” (30cm)
L = Clearance above paved sidewalk or paved 7’ (2.13m)†
driveway located on public property
M = Clearance under veranda, porch, deck or
12” (30cm)‡
12” (30cm)‡
balcony
N = Clearance above a roof shall extend a minimum of 24” (610mm) above the highest point when it passes through the roof
surface, and any other obstruction within a horizontal distance of 18” (450mm).
1 In accordance with the current CSA-B149 Installation Codes
2 In accordance with the current ANSI Z223.1/NFPA 54 National Fuel Gas Codes
† A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and
serves both dwellings
‡ only permitted if veranda, porch, deck or balcony is fully open on a minimum 2 sides beneath the floor:
NOTE: 1. Local codes or regulations may require different clearances.
2. The special venting system used on Direct Vent Fireplaces are certified as part of the appliance, with clearances tested and
approved by the listing agency.
10006326
Fig. 13 Vent termination clearances.
13
360 DVS Series Direct Vent Fireplaces
Termination Clearances
Termination clearances for buildings with combustible and noncombustible exteriors.
Inside Corner
Recessed Location
Outside Corner
A=
Combustible
6"(152mm)
Noncombustible
2"(50mm)
A
V
B=
Combustible
6"(152mm)
Noncombustible
2"(50mm)
V
C
D
E
C
V
B
Balcony with perpendicular side wall
Balcony with no side wall
V
V
G=
Combustible &
Noncombustible
12"(305mm)
C = Maximum depth of 48"
(1219mm) for recessed
location.
H
G
Combustible &
Noncombustible
D = Minimum width for back wall
of a recessed location.
Combustible 38"(965mm)
Noncombustible 24"(610mm)
J
E = Clearance from corner in
recessed location.
Combustible 6"(152mm)
Noncombustible 2"(50mm)
H = 24"(610mm)
J = 20"(508mm)
584-15
Fig. 14 Termination clearances.
General Information Assembling Vent Pipes
Canadian Installations:
Venting system must be installed in accordance with the
current CSA-B149.1 installation code.
USA Installations:
The venting system must conform with local codes and/
or current National Fuel Gas Code ANSI Z223.1/NFPA
54.
Only venting components manufactured by CFM Corporation can be used in Direct Vent systems.
Twist Lock Pipes
When using twist-lock pipe, it is not necessary to use
sealant on the joints. The only areas of the venting
system that need to be sealed with high-temperature
silicone sealant are the collars on the fireplace and termination, and sliding joints of telescopic vent sections
used in the system.
To join the twist lock pipes together, align the beads
of the male end with the grooves of the female end.
While bringing the pipes together, twist the pipe until the
flange on the female end contacts the external flange
on the male end. It is recommended that you secure the
joints with three (3) sheet metal screws; however, this is
not mandatory with twist lock pipe.
NOTE: For ease of assembly, use a lubricant (Vaseline
or similar substance) on male end of twist lock pipe
prior to assembly.
Male End
Screw Holes
Female End
TWL100
Fig. 15 Twist lock pipe joints.
14
10006326
360DVS Series Direct Vent Fireplaces
How to Use the Vent Graph
Rear Wall Application
The vent chart should be read in conjunction with the
following vent installation instructions to determine the
relationship of the vertical and horizontal dimensions of
the vent system.
When installed as a rear vent unit this appliance may be
vented directly to a termination located on the rear wall
behind the appliance.
1. Determine the height of the center of the horizontal
vent pipe exiting through the outer wall. Using this
dimension on the Sidewall Vent Graph bellow, locate
the point intersecting with slanted graph line.
2. From the point of this intersection, draw a vertical
line to the bottom of the graph.
3. Select the indicated dimension, and position the
fireplace in accordance with same.
Example A:
If vertical dimension from floor of the fireplace is 11’
(3.4 m), horizontal run to the face of outer wall must
not exceed 14’ (4.3 m).
Example B:
If vertical dimension from floor of the unit is
7’ (2.14 m), horizontal run to the face of outer wall
must not exceed 8¹⁄₂’ (2.6 m).
• Specific rear vent starter kits must be used in these
•
•
applications (see ‘venting components’). The appliance has been approved for installation flat against a
rear wall. (Fig. 17)
Maximum horizontal distance between the rear of
the appliance and the outside face of the rear wall is
20” (508 mm). (Fig. 17)
Minimum clearances between any combustible material and the vent pipe sections are:
Top ..............................................2” (51 mm)
Sides ...........................................1” (25 mm)
Bottom .........................................1” (25 mm)
Max. 20”
(508mm)
30
29
28
27
26
25
23
22
21
20
19
18
17
16
15
14
13
eg: A
12
11
10
9
Vertical dimension from floor of the unit
to center of the horizontal vent pipe
24
8
7
eg: B
6
5
4
3
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20
DV Graph
Horizontal dimension from outside of the wall
to the centerDVofGraph
the fireplace vent flange
rev. 8-8-02 rjs
Sidewall vent graph showing
the relationship between vertical and
horizontal dimensions for a Direct Vent flue system.
FP1434
Fig. 17 Rear vent application.
Rear Wall Installation
Step 1
Locate and cut vent opening in the rear wall.
Combustible walls: Cut a rectangular hole measuring
10³⁄₈” H x 9³⁄₈” W (265 x 240 mm) through the exterior
wall and frame. Frame in the opening per Figure 18.
Noncombustible walls: Cut a round hole measuring
7¹⁄₂” (190 mm) diameter through the exterior wall and
frame. (Fig. 18)
STEP 2
For combustible walls: Measure wall thickness and cut
zero clearance sleeve parts to proper length.
Max. length is 12” (305 mm). Assemble sleeve
to its maximum opening of 10³⁄₈” x 9³⁄₈” (265 x
240 mm), and attach to firestop with #8 sheetmetal
screws (supplied). Install firestop assembly. (Fig. 19)
NOTE:Zero clearance sleeve is required only for combustible walls.
Fig. 16 Sidewall vent graph.
10006326
15
360 DVS Series Direct Vent Fireplaces
STEP 5
Vent Opening for Combustible Wall
Guide vent through the vent hole as you place the appliance in its installed position. Guide the 4”
(102 mm) and 7” (178 mm) collars of the vent termination into the outer ends of the venting.
9³⁄₈”
(240mm)
Do not force the termination. If the vent pipes do not
align with the termination, remove and realign the venting at the appliance flue collars.
10³⁄₈”
(265mm)
Framing Detail
Attach the termination to the wall as outlined in the
instruction sheet supplied with the termination.
Vertical Sidewall Application
Vent Opening for Noncombustible Wall
It is very important the venting system maintain its balance between the combustion air intake and the flue
gas exhaust, certain limitations concerning vent configurations must be strictly adhered to.
7¹⁄₂”
(190mm)
VO584-100
Fig. 18 Locate vent opening on rear wall.
Maximum
Length
12” (305mm)
#8 Screws (2)
VO584-100
Vent Opening
2/99 djt
#8 Screws (2)
•
•
•
Firestop
Side View
CFM135a
• The vent graph (Fig. 16), showing relationship be-
Fig. 19 Adjustable zero clearance sleeve.
STEP 3
Measure the horizontal length requirement for the venting including a 2” (51 mm) overlap, i.e. from the elbow
to the outside wall face plus 2” (51 mm), or the distance
required if installing a second 90˚ elbow. (Fig. 20)
STEP 4
tween vertical and horizontal side wall venting, will
help determine allowable dimensions.
Minimum clearance between vent pipes and combustible materials is 1” (25 mm) on top, bottom, and
sides, unless otherwise noted.
When the vent termination exits through foundations
less than 20” (508 mm) below siding outcrop, the
vent pipe must flush up with the siding.
It is best to locate the fireplace in such a way that
minimizes the number of offsets and horizontal vent
length. The horizontal vent run refers to the total
length of vent pipe from the flue collar of the fireplace to the face of the outer wall.
NOTE: When installing the appliance as a rear vent
unit, the 90˚ transition elbow attached directly to the
rear of the unit is not included in the following criteria
and calculations. Unless it is specifically mentioned,
this elbow should be ignored when calculating venting
layouts.
Install the 4” (102 mm) vent to the appliance collar
and secure with three (3) sheetmetal screws. Install
the 7” (178 mm) vent pipe to the appliance collar and
secure with three (3) sheetmetal screws. It is not necessary to seal thisCFM135
connection.
Zero Clearance
Sleeve
It is critical
there be
no downward slope
2/26/01 sta
away from the appliance when connecting
the vent or elbow.
FP1435
Fig. 20 Maximum three (3) 90° elbows per installation.
16
10006326
360DVS Series Direct Vent Fireplaces
Horizontal plane means no vertical rise exists on this
portion of the vent assembly.
• The maximum number of 90˚ elbows per side wall
installation is three (3).
• If a 90˚ elbow is fitted directly on top of the fireplace
flange, the maximum horizontal vent run before the
termination or a vertical rise is 36” (914mm).
Max. 20”
(508mm)
Max. 36”
(914mm)
• The maximum number of 45° elbows permitted per
side wall installation is two (2). These elbows can be
installed in either the vertical or horizontal run.
• For each 45° elbow installed in the horizontal run,
the length of the horizontal run MUST be reduced by
18” (45 cm). This does not apply if 45° elbows are
installed on the vertical part of the vent system.
• The maximum number of elbow degrees in a system
is 270°. Example shown in Figure 23:
Elbow 1 = 90°
Elbow 2 = 45°
Elbow 3 = 45°
Elbow 4 = 90°
Total angular variation = 270°
1 + 2 + 3 + 4 = 270°
FP1436
Fig. 21 Maximum horizontal run w/no rise.
1
• If a 90° elbow is used in the horizontal vent run
2
(level height maintained), the maximum horizontal
vent length is reduced by 36” (914 mm). (Fig. 21)
This does not apply if the 90° elbows are used to
increase or redirect a vertical rise.
Example: According to the vent graph (Fig. 16),
the maximum horizontal vent length in a system
with a 7¹⁄₂” (191mm) vertical rise is 20 ft. (6.1m), but
if a 90° is required in the horizontal vent, it must be
reduced to 17 ft. (5.2m).
NOTE: The sum of Dim. A and Dim. B must not be
greater than 17 ft. (5.2m). (Fig. 22)
1
2
3
3
4
4
FP1438
Fig. 23 Maximum elbow usage.
Vertical Side Wall Installation
STEP 1
Locate and cut vent opening in the side wall. It may be
necessary to first position the fireplace and measure to
obtain the hole location. Depending on whether the wall
is combustible or noncombustible, cut the opening to
size per Figure 24.
90o
B
A
Combustible walls: Cut a rectangular hole measuring
9³⁄₈” H x 9³⁄₈” W (240 x 240mm) through the exterior wall
and frame. Frame in the opening per Figure 24.
A + B = 17’
(5.2m) Max.
7’6” (2.3m)
Noncombustible walls: Cut a round hole measuring
7¹⁄₂” (190 mm) diameter through the exterior wall and
frame. (Fig. 24)
STEP 2
For combustible walls: Measure wall thickness and
cut zero clearance sleeve parts to proper length. Max.
length is 12” (305mm). Assemble the sleeve and attach
it to the firestop with #8 sheet metal screws (supplied).
Install the firestop assembly. (Fig. 25)
FP1437
Fig. 22 Horizontal run reduction.
10006326
Zero clearance sleeve is required only for
combustible walls.
17
360 DVS Series Direct Vent Fireplaces
STEP 4
Vent Opening for Combustible Wall
Apply a bead of silicone to the inner and outer flue
collars of the fireplace and using appropriate length of
pipe section(s) attach to fireplace with three (3) screws.
Follow with the installation of the inner and outer elbow,
again secure joints as described in “Connecting Vent
Pipes” section.
STEP 5
9³⁄₈”
(240mm)
9³⁄₈”
(240mm)
Framing Detail
Vent Opening for Noncombustible Wall
Measure the horizontal length requirement including a
2” (51 mm) overlap, i.e. from the elbow to the outside
wall face plus 2” (51 mm) (or the distance required if
installing a second 90° elbow. (Fig. 27)
Always install horizontal venting on a level
plane.
7¹⁄₂”
(190mm)
VO584-100
X
Fig. 24 Locate vent opening on rear wall.
Maximum
Length
12” (305mm)
#8 Screws (2)
VO584-100
Vent Opening
2/99 djt
#8 Screws (2)
X
Firestop
Side View
CFM135a
Fig. 25 Adjustable zero clearance sleeve.
STEP 3
Place fireplace into position. (Fig. 26) Measure the vertical height (X) required from the base of the flue collars
to the center of the wall opening.
FP1441
Fig. 27 Horizontal length requirement.
STEP 6
X
CFM135
Zero Clearance Sleeve
2/26/01 sta
Use appropriate length of pipe section—telescopic or
fixed—and install. The 20” (508 mm) section of pipe
which goes through the wall is packaged with the
7DVSK starter kit, and can be cut to suit if necessary.
X
Seal vent pipe and firestop gaps with high temperature
sealant to restrict cold air being drawn in around the
fireplace.
STEP 7
FP1439
Fig. 26 Vertical height requirement.
18
Apply high temperature sealant to 4” (102 mm) and
7” (178 mm) collars, or to the termination 1” (25 mm)
away from the crimped end. Guide 4” and 7” collars of
vent terminations into respective vent pipes. Double
check vent pipes to see that they overlap the collars by
10006326
360DVS Series Direct Vent Fireplaces
2” (51 mm). Secure termination to the wall with screws
provided, and caulk around the wall plate to weatherproof.
Zero Clearance
Sleeve (if required)
One alternative to screwing the termination directly to
the wallis the use of expanding plugs or an approved
exterior construction adhesive.
Or, you may attach the termination with screws through
the inner body into the 4” (102 mm) vent pipe; however,
for this method, you must extend the 4” (102mm) pipe
approximately 6” (153 mm) beyond the outer face of the
wall.
7” Pipe
If installing a snorkel, a minimum 24” (610 mm)
vertical rise is necessary. The maximum horizontal
run with 24” (610 mm) vertical pipe is 36” (914mm).
The measurement is taken from the collar of the
fireplace (or transition elbow) to the face of exterior
wall. See sidewall vent graph, Page 15, for extended
horizontal runs if the vertical exceeds 24” (610 mm).
1. Establish vent hole through the wall. (Fig. 24)
2. Remove soil to depth of about 16” (406 mm) below
base of snorkel. Install window well (not supplied).
Refill hole with 12” (305 mm) of coarse gravel, leaving a clearance of about 4” (102 mm) below snorkel.
(Fig. 28)
3. Install vent system.
4. Ensure a watertight seal is made around the vent
pipe coming through the wall.
5. Apply high-temperature sealant caulking (supplied)
around 4 in. and 7 in. snorkel collars.
6. Slide snorkel into vent pipes and secure to wall.
7. Level the soil so as to maintain a 4” (102 mm) clearance below snorkel. (Fig. 29)
10006326
Min. 4” (102mm)
Clearance
(Ground)
24” (610mm)
Minimum
Gravel
Drain
Foundation Wall
• A minimum of 24” (610mm)
vertical pipe must be installed
when using the 7TDVSNORK
Kit.
• The 22” (559mm) vertical rise
(center to center) of the snorkel
may be included for calculation
of maximum horizontal run.
Below Grade Installation
NOTE:Ensure sidewall venting clearances are observed. If venting system is installed below ground,
we recommend a window well with adequate and
proper drainage.
Screws
Window Well
Support the horizontal pipes with metal
pipe straps every 36” (914mm).
When it is not possible to meet required vent terminal
clearances of 12” (305 mm) above grade level, we recommend using a starter kit. It allows installation depth
down to 7” (178 mm) below grade level. Measure 7”
(178 mm) from the center of the horizontal vent pipe as
it penetrates through the wall.
7TDVSNORK
(Snorkel)
Firestop
FP1442
Fig. 28 Below grade installation.
Do not backfill around the snorkel. A clearance of at least 4” (102mm) must be maintained between the snorkel and the soil.
If the foundation is recessed, use recess brackets (not
supplied) for securing lower portion of the snorkel. Fasten brackets to wall first, then secure to snorkel with self
drilling #8 x 1/2 sheetmetal screws. It will be necessary
to extend vent pipes out as far as protruding wall face.
(Fig. 29)
Snorkel
Foundation Wall
Wall Screws
Sheet Metal Screws
Watertight Seal
Around Pipe
CFM139
Fig. 29 Snorkel installation / recessed foundation.
CFM139
Snorkel
2/26/01 sta
rev. 9-25-02
rjs
19
360 DVS Series Direct Vent Fireplaces
Vertical Through-the-Roof Application
This Gas Fireplace has been approved for:
1 + 2 + 3 + 4 = 270°
• Vertical installations up to 40’ (12 m) in height. Up
to a 10’ (3 m) horizontal vent run can be installed
within the vent system using a maximum of two 90°
elbows. (Fig. 30)
1
2
3
4
Max. Height 40’
(12.2m)
Min. Height 8’
(2.4m)
1
2
3
4
Max. 10’ (3m)
FP1444
Fig. 31 Maximum elbow usage.
Support Straps
Every 36”
(914mm)
Min.
2' (610 mm)
Max. 10’ (3m)
Max. Height
40’ (12.2m)
Min. Height
8’ (2.4m)
FP1443
Fig. 30 Support straps
for horizontal
runs.
max height
& length
• Up to two
•
•
•
•
•
20
360DVS
45°rev.
elbows
9-17-02may
rjs
be used within the horizontal run. For each 45° elbow used on the horizontal level the maximum horizontal length must be
reduced by 18” (457 mm).
Example: Maximum horizontal length:
Zero elbows
= 10’ (3 m)
1 x 45° elbows = 8¹⁄₂’ (2.6 m)
2 x 45° elbows = 7’ (2.1 m)
A minimum of an 8 ft. (2.43 m) vertical rise.
Two (2) sets of 45° elbow offsets may be used within
the vertical sections. From zero to max 8 ft. (2.43 m)
vent pipe can be used between elbows. (Fig. 30)
7DVCS supports offsets. (Fig. 33) This application
will require you first determine the roof pitch and use
the appropriate starter kit. See Venting Components
List, Page 22.
The maximum angular variation allowed in the system is 270˚. (Fig. 31)
The minimum height of the vent above the highest
point of penetration through the roof is 2’ (610mm).
(Fig. 32)
FP1185
Fig. 32 Maximum termination to roof clearance.
10006326
360DVS Series Direct Vent Fireplaces
Vertical Through-the-Roof Installation
1. Locate your fireplace.
2. Plumb to center of the (4”) flue collar from ceiling
above and mark position.
3. Cut an opening equal to 9³⁄₈” x 9³⁄₈” (240 x 240mm).
4. Proceed to plumb for additional openings through
the roof. In all cases, the opening must provide a
minimum of 1” (25 mm) clearance to the vent pipe,
i.e., the hole must be at least 9³⁄₈” x 9³⁄₈” (240 x
240mm).
5. Place fireplace into position.
6. Place firestop(s) #7DVFS or Attic Insulation Shield
#7DVAIS into position and secure. (Fig. 35)
7. Install roof support (Fig. 33) and roof flashing making
sure upper flange is below the shingles. (Fig. 34)
8. Install appropriate pipe sections until the venting is
above the flashing. (Fig. 34)
9. Install storm collar and seal around the pipe.
10. Add additional vent lengths for proper height.
(Fig. 32)
11. Apply high temperature sealant to 4” and 7” collars
of vertical vent termination and install.
If there is a room above ceiling level, a
firestop spacer must be installed on both
the bottom and the top sides of the ceiling
joists. (Fig. 35) If an attic is above ceiling
level, a 7DVAIS (Attic Insulation Shield)
must be installed.
NOTE:The enlarged ends of the vent sections are to
always face downward.
Attic Insulation
Shield
Joist
Ceiling Installation
11"
(279 mm)
11"
(279 mm)
Upper Floor
Joist
Firestop
Spacer
Nails (4)
Typical Roof Support Application
Typical Ceiling Support Application
CFM110
Fig. 33 Chimney support.
CFM100
Fig. 35 Firestop and attic insulation shield.
CFM100_
Firestop_Vertical
032803 rjs
CFM110
Typical ceiling/roof support
10/90
Sheet Metal Screws (#5)
(3 per joint)
Sealant
Storm Collar
TWL101a
Fig. 34 Roof flashing.
10006326
TWL101a
Twist Lock Pipe
2/8/99 djt
21
360 DVS Series Direct Vent Fireplaces
Twist Lock Venting Components
7TDVRVT Through-the-Wall Rear Vent Termination
584A
venting components
rear vent term
4/6/99 djt
Starter Kit Model 7TDVSK - Sidewall
Starter Kit Model 7TDVSKV - Vertical Venting
for 7TDVSKV-A: order 1/12 to 6/12 roof pitch
for 7TDVSKV-B: order 7/12 to 12/12 roof pitch
for 7TDVSKV-F: order flat roof
Starter Kit Model 7TDVSKS - Snorkel Kit
Snorkel Termination - 7TDVSNORK
for Below Grade Installation
45˚ Elbow
7TDVT45 for Rear Vent to Vertical Vent
or Vertical/Horizontal Offsets
584B
Vent components
584CKit
Starter
Vent components
2/25/99
djt
584D
45 degree elbow
Vent Components
2/25/99 djt
90 degree elbow
10/20/99 twistlock
2/25/99 djt
584E
10/20/99 twist lock
Venting Components
Telescope vent
2/25/99 djt
10/20/99 twist lock
584F
Venting Components
Pipe sections
2/25/99 djt
10/20/99 twist lock
584G
Venting Components
Firestop spacer
2/25/99 djt
584H
Venting components
attic insulation shield
2/25/99 djt
22
584I
vent components
offset support
2/25/99 djt
90˚ Transition Elbow
7TDVRT90 for Rear Vent to Vertical Vent
90° Elbow
7TDV90 Vertical/Horizontal Offset
Telescopic Vent Sections:
7TDVP1218 - 12” to 18” adjustable length
7TDVP3564 - 35” to 64” adjustable length
Pipe Sections for vertical or horizontal venting:
Model 7TDVP8”
4 per box
Model 7TDVP12”
4 per box
Model 7TDVP24”
4 per box
Model 7TDVP36”
Model 7TDVP48”
Firestop Spacer
Model 7DVFS
Attic Insulation Shield
Model 7DVAIS
Vertical/ Horizontal Combination Offset Support
Model 7DVCS
10006326
360DVS Series Direct Vent Fireplaces
Operating Instructions
Glass Information
Only glass approved by CFM Corporation
should be used on this fireplace.
• The use of any non-approved replacement glass will
void all product warranties.
• Care must be taken to avoid breakage of the glass.
• Do not operate appliance with glass front
removed, cracked or broken.
• Replacement glass (complete with gasket) is
available through your Majestic Fireplaces
dealer and should only be installed by a licensed
qualified service person.
7. To reinstall the window frame assembly reverse
this procedure.
Front Window Frame Assembly
1. Remove the top and bottom louvre assembly.
2. Remove the lower window trim (held in place with
magnets).
3. Remove both lower retaining screws. Access to
these screws is gained through the holes along the
lower edge of the frame behind the trim. (Fig. 38)
4. Tilt lower edge of frame out slightly and lift window
frame assembly up and away from the fireplace.
5. To reinstall the window frame assembly reverse
the process.
Louvre Removal
• The top side and top end louvres are removed by
•
•
simply lifting the louvre assembly and pulling the assembly away from the fireplace. (Fig. 36)
The lower side louvres are hinged along there lower
edge and are folded down for access to components
in the base cavity of the fireplace.
The lower end louvre assembly on the 360DVS3/
SL/ SR units is removed in the same manner as the
top louvre assemblies.
Lower Clamps
Window
Frame
Assembly
2.
Louvre
1.
Window
Frame
Assembly
Pull Clamp
Push Hook
Clamp
HanFP1228
Fig. 37 Window frame assembly removal.
FP1228
remove glass frame
11/02
Glass Panel
FP1227
Fig. 36 Remove louvre assembly top.
Window FrameFP1227
Assembly Removal
Side Window Frame Assemblies
Louvre removal
1. Shut off the gas supply.
11/02
2. Allow the fireplace to cool if it has been in operation.
3. Remove the top louvre assembly.
4. Lower the bottom louvre assembly.
5. Release the two clamps along lower edge of the
frame by pulling down on clamp handles. (Fig. 37)
6. Tilt lower edge of frame out slightly and lift window
frame assembly up and away from the fireplace.
10006326
Location of Lower
Retaining Screws
FP1445
Fig. 38 Retaining screw.
Remove_end_glass&frame
360DVS
rev. -9-17-02 rjs
23
360 DVS Series Direct Vent Fireplaces
Glass Cleaning
It is necessary to periodically clean glass. During startup, condensation, which is normal, forms on the inside
of the glass. This condensation causes lint, dust and
other airborne particles to cling to glass surface.
Also initial paint curing may deposit a slight film on the
glass. It is therefore recommended glass be cleaned
two or three times with a non-ammonia based household cleaner and warm water. The use of fireplace glass
cleaner is recommended within the first few weeks of
operation.
After the initial cleaning process the glass should be
cleaned two or three times during each operating season depending on the environment in the house.
Clean the glass after the first two weeks of
operation.
Do not clean the glass when hot.
Do not use an abrasive cleaner.
Do not strike or slam the glass.
Ceramic Refractory Installation
The vertical refractory panels are installed in the unit
prior to shipment. For assembly procedures, refer to
Figure 39.
1. Unpack the ceramic refractory panels from the carton.
Handle the refractory material carefully, the
panels are fragile.
2. Place the two end floor refractory panels on the base
of the fireplace.
3. Place both side panels along the side of the base.
NOTE: 360DVS2 is the only 360DV unit that is fitted
with two (2) end vertical panels, as shown in Figure
39. 360DVSL and 360DVSR units are each fitted
with one end vertical panel and two side vertical
panel. The 360DVS3 has only one end vertical
panel.
Vertical Panels in
Place When Shipped
Floor Panels Placed
During Installation
FP1446
Log Installation
Refer to Figures 40 and 41 for log location and alignment.
Because of the log stack design, these instructions can
be followed from either side of the fireplace. To follow
these instructions, identify the logs by the number cast
into the underside.
For correct operation of the fireplace, the logs must be
correctly placed in the sequence described below:
1. Unpack the logs from the shipping carton. The logs
are fragile; handle them carefully.
Handle and dispose of plastic bags in
which logs were shipped in a safe manner.
As with all plastics, they are not toys and
should be kept away from infants.
2. Remove both sides of the window frame assembly
(where applicable).
3. Place the log rear (B120) on the grate. The square
hole located on the underside of the log is to be
placed over the center of the grate. The inner end
of the log ensures that the bottom hole is located on
the pin of the support.
4. Place the log front left (B121) on the grate. The
square hole located on the underside of the log is to
place over the corner leg of the grate. The inner end
of the log ensures the bottom holes are located on
the pin of the support.
5. Place the log front right (B122). Once more, the
square hole fits over the corner leg of the grate.
The inner end of this log maintains a recess on the
underside, which locates over the knob on the top of
the log front left (B121) to secure the inner end in
place.
6. Place the log rear left (B123). The bottom back of
the log rests on the grate. The notch at the back of
the log locates over the knob on the top of the log
rear (B120). The bottom of the log rests on top of
the log front left (B121).
7. Place the log bottom left (B124). The log maintains
a step on the outer end, which rests against the
prong of the grate. The alternate end rests on the
side floor refractory panel.
8. Place the log rear right (B125). The log maintains a
hole on the underside, which rests over the knob on
the top of the log rear (B120). The bottom of the log
rests against the side floor refractory panel, and the
side rests against the last prong of the grate.
9. Place the log center (B126). The log maintains a
hole on the underside, which rests over the knob on
the top of the log front right (B122). The alternate
end rests against the side floor refractory panel and
positions between the two (2) prongs of the grate.
Fig. 39 CeramicFP1446
panel installation.
24
Cer_refract_panels-designer
360DVS
10006326
360DVS Series Direct Vent Fireplaces
Side of Fireplace
B120
B125
B122
B126
Venting Side
B123
B124
B121
LG320
Fig. 40 360DVS log placement.
Venting Side
B121
Side of Fireplace
B123
B120
LG320
360DVS
logs
B122
B126
B125
LG321
Fig. 41 360DVS log placement.
Your log set contains Ember Material and two types of
Lava Rocks. Set these materials in place after the logs
have been installed.
Ember Material (Pt. #51915)
Flame & Temperature Adjustment
RN/ RP Models
For units equipped with ‘HI/LO’ valves the flame adjustment is accomplished by rotating the ‘HI/LO’ adjustment
knob located near the center of the gas control valve.
(Fig. 42 and Fig. 43)
Remove ember material from the bag and separate it
LG321
into small pieces, then scatter it over burner tiles in
a
Turn
random fashion. Do not pack down ember material;
360DVS
counterclockwise
leave it in a ‘fluffy’ state.
logs opposite side
to decrease
Lava Rock (Pt. #10001454)
flame height
Remove lav rock material from packaging and spread
it over ceramic floor panels outside log stack. Do not
place this lava rock material on burner tiles.
LO
Lava Rock and Ember Material Placement
HI
Turn clockwise
to increase
flame height
Fig. 42 Flame adjustment knob for Honeywell valve.
25
10006326
HV102
Honeywell hi/lo knob
4/5/99 djt
360 DVS Series Direct Vent Fireplaces
HI
Turn
counterclockwise
to increase
flame height
LO
Turn clockwise
to decrease
flame height
3/8” - 1/2”
(10 - 13mm)
Fig. 43 Flame adjustment knob for SIT valve.
Flame Characteristics
FP390
F584-703
Fig. 45 Correct pilot flame appearance.
It is important to periodically
performKNOB
a visual check
FLAME ADJUSTMENT
11/21/96
of the pilot and burner
flames. Compare them to the
pictorials illustrated below. (Figs. 45 & 46) If the flame
patterns appear abnormal, contact a qualified service
provider for service and adjustment.
LG322
LG323
Fig. 46 Correct log flame appearance.
26
10006326
360 DVS Series Direct Vent Fireplaces
Maintenance
Burner and Burner Compartment
It is important to keep the burner and the burner compartment clean. At least once per year remove the logs
and lava rock/ember material. Vacuum and wipe out the
burner compartment. Remove and refit the logs per the
instructions in this manual.
Always handle the logs with care as they
are fragile and may also be hot if the fireplace has been in use.
FK24/FK12 Fan Assembly
The fan unit requires periodic cleaning. At least once
per month in the operating season, open the lower louvre panels and wipe or vacuum the area around the fan
to remove any build up of dust or lint.
Brass Trim
Clean the brass trim pieces using a soft cloth lightly
dampened with lemon oil. Do not use water or household cleaners on any brass components.
Cleaning the
Standing Pilot Control System
The burner and control system consists of:
• burner tube
• gas orifice
• pilot assembly
• thermopile
• millivolt gas valve
To obtain proper operation, it is imperative that the pilot
and burner’s flame characteristics are steady, not lifting
or floating.
Typically, the top 3/8 – 1/2” (10 – 13 mm) of the thermopile should be engulfed in the pilot flame. (Page 26, Fig.
46)
To adjust pilot burner (to be done by a qualified service
technician):
1. Remove pilot adjustment cap.
2. Adjust pilot screw to provide properly sized flame.
3. Replace pilot adjustment cap.
The primary air shutter is set at factory and should be
adjusted, if necessary, only by a qualified service technician.
Cleaning Electronic Ignition System
The Electronic Ignition burner/control system consists
of:
•
•
•
•
main burner
gas orifice
pilot burner
24VAC valve with transformer
The process for taking care of Electronic Ignition units is
identical to that for taking care of Standing Pilot models.
Most of these components may require only an occasional checkup and cleaning and some may require adjustment. If repair is necessary, it should be performed
by a qualified technician.
1. Turn off pilot light at gas valve side.
2. Let fireplace cool if it has been running.
3. Remove window frame assembly. (Refer to Window
Frame Assembly Removal section)
4. Remove logs.
5. Vacuum burner compartment especially around
orifice primary air openings.
6. Visually inspect pilot. Brush or blow away any dust
or lint accumulation.
7. Reinstall logs.
8. Ignite pilot; refer to Lighting Instructions.
9. Reinstall window frame assembly.
34
10006326
360DVS Series Direct Vent Fireplaces
1
1g
1f
1c
1a
8
1b
1e
1d
3a/b
2
11
9
14
O H
7
4a/b
OFF
12
PILOT
ADJ
L
ON P
IL
O
I
10
6
16a/b
T
13
5a/b
11
15a/b
20
22
24
25
26
29
27
19
28
23
18
21
17
31a/b
36
30
35
34a/b
37
25
LO
32
HI
33
CFM Corporation reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time,
6326
without notice.
360DVS Series
10006326
360DVS
parts
35
360 DVS Series Direct Vent Fireplaces
360DVS Series
Ref.
1.
1a.
1b.
1c.
1d.
1e.
1f.
1g.
2.
3a.
3b.
*
*
*
4a.
4b.
5a.
5b.
6.
7.
8.
*
*
*
*
*
*
*
9.
10.
11.
12.
13.
14.
15a.
15b.
16a.
16b.
17.
18.
*
*
*
*
19.
*
*
20.
36
(Items marked ‘*’ are not shown in the parts illustration)
Description
360DVS2
360DVS3
360DVSL
360DVSR
Log Set (complete)
10006350
10006350
10006350
10006350
Log - Rear (B120)
10006315
10006315
10006315
10006315
Log - Front Left (B121)
10006316
10006316
10006316
10006316
Log - Front Right (B122)
10006317
10006317
10006317
10006317
Log - Rear Left (B123)
10006318
10006318
10006318
10006318
Log - Bottom Left (B124)
10006319
10006319
10006319
10006319
Log - Rear Right (B125)
10006320
10006320
10006320
10006320
Log - Center Right (B126)
10006321
10006321
10006321
10006321
Grate Assembly
10006014
10006014
10006014
10006014
Burner Housing Assembly, Nat.
10006148
10006148
10006148
10006148
Burner Housing Assembly, Prop.
10006299
10006299
10006299
10006299
Ceramic Burner Tile
10002165
10002165
10002165
10002165
Orifice/s, Main burner (Nat.)
Refer to the rating plate for specific orifice information
Orifice/s, Main Burner (Prop.)
Refer to the rating plate for specific orifice information
Pilot assembly PSE (Nat.)
10001741
10001741
10001741
10001741
Pilot assembly PSE (Prop.)
10001742
10001742
10001742
10001742
Pilot assembly SIT Top Conv. (Nat.)
10002264
10002264
10002264
10002264
Pilot assembly SIT Top Conv. (Prop.)
10002265
10002265
10002265
10002265
Pilot, PSE (with cable & electrode)
10001824
10001824
10001824
10001824
Pilot SIT Top Convertible
10002266
10002266
10002266
10002266
Pilot Hood, SIT Top Convertible
10002385
10002385
10002385
10002385
Orifice, Pilot PSE (Nat.)
10001822
10001822
10001822
10001822
Orifice, Pilot PSE (Prop.)
10001823
10001823
10001823
10001823
Orifice, Pilot SIT Top convertible (Nat.)
10002268
10002268
10002268
10002268
Orifice, Pilot SIT Top conv. (Prop.)
10002269
10002269
10002269
10002269
Pilot tube & fittings (Top convertible)
10001296
10001296
10001296
10001296
Manifold tube & fittings
10002492
10002492
10002492
10002492
Flexible Gas Line (18”) with fittings
20002500
20002500
20002500
20002500
Thermocouple, PSE
10001828
10001828
10001828
10001828
Thermocouple, SIT Top Convertible
53373
53373
53373
53373
Thermopile
51827
51827
51827
51827
Ignitor electrode (with cable), SIT
10001297
10001297
10001297
10001297
Ignitor (Piezo), SIT 820 valve
52464
52464
52464
52464
Ignitor (Piezo), Honeywell Valve
20000062
20000062
20000062
20000062
Valve, SIT 820 (Nat.)
52677
52677
52677
52677
Valve, SIT 820 (Prop.)
52678
52678
52678
52678
Valve, Honeywell (Nat.)
10001782
10001782
10001782
10001782
Valve, Honeywell (Prop.)
10001759
10001759
10001759
10001759
Fan & Bracket FK12 (optional)
ZA1110
ZA1110
ZA1110
ZA1110
Fan & Bracket FK24 (optional)
54103
54103
54103
54103
Temperature Sensor (optional)
51704
51704
51704
51704
Fan Speed Control (optional)
51738
51738
51738
51738
Fan Speed Control Knob (optional)
51882
51882
51882
51882
Electric Cord
51865
51865
51865
51865
Remote ON/OFF switch (RN/RP models)
51842
51842
51842
51842
Wiring Harness (remote switch)
55923
55923
55923
55923
Remote ON/OFF Switch Kit (incls. bracket)
53875
53875
53875
53875
Louvre Assembly, side top.
10000039
10000039
10000039
10000039
10006326
360DVS Series Direct Vent Fireplaces
360DVS Series (continued)
Ref.
21.
22.
23.
24.
25.
26.
*
*
*
*
*
27.
28.
29.
30.
*
*
*
*
*
*
*
*
*
*
*
*
31a.
31b.
32.
33.
34a.
34b.
35.
36.
37.
*
(Items marked ‘*’ are not shown in the parts illustration)
Description
Louvre Assembly, side bottom
Louvre Assembly, end top
Louvre Assembly, end bottom
Hinge, lower louvre assemblies
Trim Window Top/Bottom w/Magnets PB
Trim Window Top/Bottom w/Magnets PB
Window Frame Assembly, side
Window Frame Assembly, end
Window Glass (complete with gasket), side
Window Glass (complete with gasket), end
Gasket Kit (glass replacement, 1x11’ length)
Window Frame Clamp
Refractory Lining (vertical end walls)
Refractory Lining (vertical side wall)
CR Bottom Kit w/out Rear
Air Inlet Cover Plate Assembly
Air Inlet Cover Plate Gasket
Flue Pipe Plate Assembly
FluePipe Plate Gasket
Flue Cover Plate
Flue Cover Plate Gasket
Relief Plate (with gasket)
Deflector, Cabinet Top Short
Corner Post (left)
Corner Post (right)
Corner Post Mounting Bracket
Deflector Cabinet Top Long
Pilot Assembly SIT Top Convertible EN
Pilot Assembly SIT Top Convertible EP
Ignitor Electrode SIT EN/EP
Cable Ignitor SIT EN/EP
SIT822 Gas Control Valve EN
SIT822 Gas Control Valve EP
Sensing Electrode (w/ Cable) EN/EP
Transformer 24V EN/EP
Ignition Module Honeywell EP
Wire Harness Honeywell EN/EP
10006326
360DVS2
10000040
N/A
N/A
52356
57483
n/a
10002483
N/A
10002533
N/A
57317
54174
10006254
N/A
10006257
10006174
10006171
10002554
10002237
10002298
10002233
10002429
N/A
N/A
N/A
N/A
54364
10002387
10002388
52465
10000696
57884
57883
57885
7522409
20000005
10001979
360DVS3
10000040
10002411
10002412
52356
57483
10006197
10002483
10002484
10002533
10002534
57317
54174
10006254
N/A
10006257
10006174
10006171
10002554
10002237
10002298
10002233
10002429
10002260
10006190
10006191
10006195
54364
10002387
10002388
52465
10000696
57884
57883
57885
7522409
20000005
10001979
360DVSL
10000040
10002411
10002412
52356
57483
10006197
10002483
10002484
10002533
10002534
57317
54174
10006254
10006285
10006257
10006174
10006174
10002554
10002237
10002298
10002233
10002429
10002260
10006190
10006191
10006195
54364
10002387
10002388
52465
10000696
57884
57883
57885
7522409
20000005
10001979
360DVSR
10000040
10002411
10002412
52356
57483
10006197
10002483
10002484
10002533
10002534
57317
54174
10006254
10006285
10006257
10006174
10006171
10002554
1000223
10002298
10002233
10002429
10002260
10006190
10006191
10006195
54364
10002387
10002388
52465
10000696
57884
57883
57885
7522409
20000005
10001979
37
360DVS Series Direct Vent Fireplaces
LIMITED LIFETIME WARRANTY
PRODUCT COVERED BY THIS WARRANTY
All Vermont Castings gas stoves, gas inserts, and gas fireplaces, and all Majestic brand gas fireplaces equipped with
an Insta-Flame Ceramic Burner, or standard steel tube burner.
BASIC WARRANTY
CFM Corporation (hereinafter referred to collectively as the Company)
warrants that your new Vermont Castings or Majestic Gas Fireplace/
Stove is free from manufacturing and material defects for a period of
one year from the date of purchase, subject to the following conditions
and limitations.
•
•
EXTENDED LIFETIME WARRANTY
The heat exchanger, where applicable, and combustion chamber
of every Vermont Castings or Majestic gas product is warranted for
life against through wall perforation. All appliances equipped with an
Insta-Flame Ceramic Burner have limited lifetime coverage on the
ceramic burner plaque. Warrantees are made to the original owner
subject to proof of purchase and the conditions and limitations listed
on this Warranty Document
•
•
COMPONENT WARRANTY
CAST IRON: All external and internal cast iron parts are warranted for a
period of three years.
Note: On porcelain enamel finished external parts and accessories The
Company offers no Warranty on chipping of enamel surfaces. Inspect
all product prior to accepting it for any damage to the enamel.
The salt air environment of coastal areas or a high humidity environment
can be corrosive to the porcelain enamel finish. These conditions can
cause rusting of the cast iron beneath the porcelain enamel finish,
which will cause the finish to flake off.
Dye lot variations with replacement parts and/or accessories can occur
and are not covered by warranty.
GLASS DOORS: Glass doors are covered for a period of one year.
Glass doors are not warranted for breakage due to misuse or accident.
Glass doors are not covered for discoloration or burned in stains due to
environmental issues, or improper cleaning and maintenance.
BRASS PLATED PARTS AND ACCESSORIES: Brass parts should be
cleaned with Lemon oil only. Brass cleaners cannot be used. Mortar
mix and masonry cleaners may corrode the brass finish. The Company
will not be responsible for, nor will it warrant any brass parts which are
damaged by external chemicals or down draft conditions.
•
•
•
•
•
GAS VALVES: Gas valves are covered for a period of one year
ELECTRONIC AND MECHANICAL COMPONENTS: Electronic and
mechanical components of the burner assembly are covered for one year.
All steel tube burners are warranted for one year.
ACCESSORIES: Unless otherwise noted all components and CFM
Corporation company supplied accessories are covered for a period of
one year.
CONDITIONS AND LIMITATIONS
•
•
•
•
This new Vermont Castings or Majestic product must be installed by
a competent, authorized, service contractor. A licensed technician, as
prescribed by the local jurisdiction must perform any installation/service
work. It must be installed and operated at all times in accordance with
the Installation and Operating instructions furnished with the product.
Any alteration, willful abuse, accident, or misuse of the product shall
nullify this warranty.
This warranty is non-transferable, and is made to the original owner,
provided that the purchase was made through an authorized supplier
of the Company.
The customer must pay for any Authorized Dealer in-home travel fees
or service charges for in-home repair work. It is the dealers option
whether the repair work will be done in the customer’s home or in the
dealer’s shop.
If upon inspection, the damage is found to be the fault of the manufacturer,
repairs will be authorized at no charge to the customer parts and/or
labor.
10006326
•
•
Any part and/or component replaced under the provisions of this
warranty is covered for six months or the remainder of the original
warranty, whichever is longest.
This warranty is limited to the repair of or replacement of part(s) found
to be defective in material or workmanship, provided that such part(s)
have been subjected to normal conditions of use and service, after
said defect is confirmed by the Company’s inspection.
The company may, at its discretion, fully discharge all obligations
with respect to this warranty by refunding the wholesale price of the
defective part(s)
Any installation, labor, construction, transportation, or other related
costs/expenses arising from defective part(s), repair, replacement,
or otherwise of same, will not be covered by this warranty, nor shall
the Company assume responsibility for same. Further, the Company
will not be responsible for any incidental, indirect, or consequential
damages except as provided by law.
SOME STATES DO NOT ALLOW FOR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOUR
CIRCUMSTANCES. THIS WARRANTY GIVES YOU SPECIFIC
RIGHTS AND YOU MAY HAVE OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
All other warranties-expressed or implied- with respect to the product,
its components and accessories, or any obligations/liabilities on the
part of the Company are hereby expressly excluded.
The Company neither assumes, nor authorizes any third party to
assume on its behalf, any other liabilities with respect to the sale of
this Vermont Castings or Majestic product
The warranties as outlined within this document do not apply to
chimney components or other non CFM Corporation accessories used
in conjunction with the installation of this product..
Damage to the unit while in transit is not covered by this warranty but
is subject to claim against the common carrier. Contact the dealer
from whom you purchased your fireplace/stove (do not operate the
appliance as this might negate the ability to process the claim with
the carrier).
The Company will not be responsible for:
a) Down drafts or spillage caused by environmental conditions such
as near-by trees, buildings, roof tops, hills, or mountains.
b) Inadequate ventilation or negative air pressure caused by
mechanical systems such as furnaces, fans, clothes dryers, etc.
This warranty is void if:
a) The fireplace has been operated in atmospheres contaminated
by chlorine, fluorine, or other damaging chemicals.
b) The fireplace has been subjected to prolonged periods of dampness
or condensation
c) Any damages to the fireplace, combustion chamber, heat exchanger
or other components due to water, or weather damage, which is the
result of but not limited to, improper chimney/venting installation.
d) Any alteration, willful abuse, accident, or misuse of the product
has occurred.
IF WARRANTY SERVICE IS NEEDED…
1) Contact your supplier. Make sure you have your warranty,
your sales receipt, and the model/serial number of your CFM
Corporation product.
2) DO NOT ATTEMPT TO DO ANY SERVICE WORK
YOURSELF.
43
Efficiency Ratings
Model
360DVS2RN
360DVS2RP
360DVS2EN
360DVS2EP
360DVS3RN
360DVS3RP
360DVS3EN
360DVS3EP
360DVSLRN
306DVSLRP
360DVSLEN
360DVSLEP
360DVSRRN
360DVSRRP
360DVSREN
360DVSREP
EnerGuide Ratings
Fireplace Efficiency (%)
62.4
62.4
62.4
62.4
62.4
62.4
62.4
62.4
62.4
62.4
62.4
62.4
62.4
62.4
62.4
62.4
Steady State (%)
Fan-OFF
Fan-ON
83
84
83
84
83
84
83
84
83
84
83
84
83
84
83
84
83
84
83
84
83
84
83
84
83
84
83
84
83
84
83
84
CFM Corporation
2695 Meadowvale Blvd. • Mississauga, Ontario, Canada L5N 8A3
800-668-5323 • www.cfmcorp.com
D.O.E.
(AFUE%)
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65
65