Bosch LTC 9441 Series Instruction manual

LTC 9418 & LTC 9420 Series
LTC 9440 & LTC 9441 Series
Instruction Manual
EN Medium & Heavy Duty
Pan Tilts
IMPORTANT SAFEGUARDS
12. Power Lines - An outdoor system should not be located in the
vicinity of overhead power lines or other electric light or power
circuits or where it can fall into such power lines or circuits.
When installing an outdoor system, extreme care should be
taken to keep from touching such power lines or circuits as
contact with them might be fatal. U.S.A. models only - refer to
the National Electrical Code Article 820 regarding installation
of CATV systems.
13. Overloading - Do not overload outlets and extension cords as
this can result in a risk of fire or electric shock.
14. Object and Liquid Entry - Never push objects of any kind into
this unit through openings, as they may touch dangerous
voltage points or short out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the unit.
15. Servicing - Do not attempt to service this unit yourself as
opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service
personnel.
16. Damage Requiring Service - Unplug the unit from the outlet
and refer servicing to qualified service personnel under the
following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled or objects have fallen into the
unit.
c. If the unit has been exposed to rain or water.
d. If the unit does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions, as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the unit to its normal operation.
e. If the unit has been dropped or the cabinet has been
damaged.
f. When the unit exhibits a distinct change in performance-this indicates a need for service.
17. Replacement Parts - When replacement parts are required, be
sure the service technician has used replacement parts
specified by the manufacturer or have the same characteristics
as the original part. Unauthorized substitutions may result in
fire, electric shock, or other hazards.
18. Safety Check - Upon completion of any service or repairs to
this unit, ask the service technician to perform safety checks to
determine that the unit is in proper operating condition.
19. Coax Grounding - If an outside cable system is connected to
the unit, be sure the cable system is grounded. U.S.A. models
only--Section 810 of the National Electrical Code, ANSI/NFPA
No.70, provides information with respect to proper grounding
of the mount and supporting structure, grounding of the coax
to a discharge unit, size of grounding conductors, location of
discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.
20. Lightning - For added protection of this unit during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect
the cable system. This will prevent damage to the unit due to
lightning and power line surges.
1. Read Instructions - All safety and operating instructions should
be read before the unit is operated.
2. Retain Instructions - The safety and operating instructions
should be retained for future reference.
3. Heed Warnings - All warnings on the unit and in the operating
instructions should be adhered to.
4. Follow Instructions - All operating and use instructions should
be followed.
5. Cleaning - Unplug the unit from the outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth
for cleaning.
6. Attachments - Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
7. Accessories - Do not place this unit on an unstable stand,
tripod, bracket, or mount. The unit may fall, causing serious
injury to a person and serious damage to the unit. Use only
with a stand, tripod, bracket, or mount recommended by the
manufacturer or sold with the product. Any mounting of the
unit should follow the manufacturer's instructions and should
use a mounting accessory recommended by the manufacturer.
An appliance and cart combination should be moved
with care. Quick stops, excessive force, and uneven
surfaces may cause the appliance and cart
combination to overturn.
8. Ventilation - Openings in the enclosure, if any, are provided
for ventilation, to ensure reliable operation of the unit, and to
protect it from overheating. These openings must not be
blocked or covered. This unit should not be placed in a builtin installation unless proper ventilation is provided or the
manufacturer's instructions have been adhered to.
9. Power Sources - This unit should be operated only from the
type of power source indicated on the marking label. If you are
not sure of the type of power supply you plan to use, consult
your appliance dealer or local power company. For units
intended to operate from battery power or other sources, refer
to the operating instructions.
10. Grounding or Polarization - This unit may be equipped with a
polarized alternating-current line plug (a plug having one
blade wider than the other). This plug will fit into the power
outlet only one way. This is a safety feature. If you are unable
to insert the plug fully into the outlet, try reversing the plug. If
the plug should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the safety purpose
of the polarized plug.
Alternately, this unit may be equipped with a 3-wire
grounding-type plug, a plug having a third (grounding) pin.
This plug will only fit into a grounding-type power outlet. This
is a safety feature. If you are unable to insert the plug into the
outlet, contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the grounding-type plug.
11. Power Cord Protection - Power supply cords should be routed
so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to
cords and plugs, convenience receptacles, and the point where
they exit from the appliance.
2
SAFETY PRECAUTIONS
SICHERHEITSVORKEHRUNGEN
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK
VORSICHT: UM EINEN ELEKTRISCHEN
DO NOT OPEN COVERS. NO USER SERVICEABLE PARTS
SCHLAG ZU VERMEIDEN, ABDECKUNG NICHT ENTFERNEN.
INSIDE.
WARTUNGEN ALLER ART QUALIFIZIERTEM PERSONAL
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
ÜBERLASSEN.
The lightning flash with an arrowhead
symbol within an equilateral triangle is
intended to alert the user to the presence
of uninsulated "dangerous voltage" within
the product's enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
Das Blitzsymbol im gleichseitigen Dreieck
soll den Benutzer auf nicht isolierte
"Hochspannung" im Gehäuse aufmerksam
machen, die eventuell stark genug ist, um
einen elektrischen Schlag zu verursachen.
The exclamation point within an
equilateral triangle is intended to alert
the user to presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
Das Ausrufezeichen im gleichseitigen
Dreieck soll den Benutzer auf wichtige
Bedienungs- und Wartungsanleitungen in
der dem Gerät beigefügten Literatur
aufmerksam machen.
SECURITE
PRECAUCIONES DE SEGURIDAD
DANGER: POUR ÉVITER TOUT RISQUE
PRECAUCION: PARA REDUCIR EL RIESGO DE CHOQUE
ELÉCTRICO, FAVOR NO ABRIR LA CUBIERTA. ESTE EQUIPO NO
CONSTA DE PIEZAS O PARTES QUE REQUIEREN SERVICIO O
MANTENIMIENTO. PARA REPARACIONES FAVOR REFERIRSE A
UN TÉCNICO CALIFICADO.
D'ÉLECTROCUTION, NE PAS OUVRIR LE BOÎTIER. IL N'Y A
PAS DE PIÈCES REMPLAÇABLES À L'INTÉRIEUR. POUR
TOUTE RÉVISION, S'ADRESSER À UN
TECHNICIEN SPÉCIALISÉ.
L'éclair fléché dans un triangle équilatéral,
avertit l'utilisateur de la présence d'une
"tension dangereuse" non isolée à
l'intérieur de l'appareil et d'une valeur
suffisante pour constituer un risque
d'électrocution.
El símbolo representado por un relámpago con
punta de flecha dentro de un triángulo equilátero, se muestra con el objetivo de alertar al
usuario que existen "voltages peligrosos" sin
aislamiento, dentro de la cubierta de la unidad.
Dichos voltages pueden ser de tal magnitud
que constituyen un riesgo de choque eléctrico
a personas.
Le point d'exclamation contenu dans un
triangle équilatéral, avertit l'utilisateur de
la présence, dans la documentation qui
accompagne l'appareil, de consignes
d'utilisation et de maintenance
importantes.
El símbolo de exclamación dentro de un
triángulo equilátero, se muestra con el
objetivo de alertar al ususario de que
instrucciones de operación y
mantenimiento importantes acompañan
al equipo.
3
CONTENTS
1
2
3
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
4
4.1
4.2
4.3
4.4
4.5
4.6
5
6
7
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Model Designation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Recommended Mounting Equipment . . . . . . . . . . . . . . . . . . .5
Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Camera/Lens/Enclosure Mounting . . . . . . . . . . . . . . . . . . . . .5
Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Grounding Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Connector Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Pan Stops (345° Models) . . . . . . . . . . . . . . . . . . . . . . . . . . .8
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Manual Pan Operation (345° Models) . . . . . . . . . . . . . . . . .8
Auto-Pan Operation (345º Models) . . . . . . . . . . . . . . . . . . .8
Pan Stop Adjustment (345° Models) . . . . . . . . . . . . . . . . . .8
Pan Operation (360° Models) . . . . . . . . . . . . . . . . . . . . . . .8
Tilt Stop Adjustment (All Models) . . . . . . . . . . . . . . . . . . . .9
Pre-Position Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
WIRING DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
RECOMMENDED APPLICATIONS . . . . . . . . . . . . . . . . .13
DIMENSIONAL OUTLINE . . . . . . . . . . . . . . . . . . . . . . . .13
1 UNPACKING
2 SERVICE
This electro-mechanical equipment should be unpacked carefully
and handled with care.
If the unit ever needs repair service, the customer should contact
the nearest Bosch Security Systems, Inc. Service Center for authorization to return and shipping instructions.
Check for the following items:
• Model number of unit.
• 3/32-inch Allen wrench.
• Connector Kit 315 1232 001
Service Centers
If an item appears to have been damaged in shipment, replace it
properly in its carton and notify the shipper. If any items are
missing, notify Bosch Security Systems.
U.S.A.: 800-366-2283 or 408-956-3895
Fax: 800-366-1329 or 408-956-3896
Email: NationalServiceCenter@ca.slr.com
Canada: 514-738-2434
Europe, Middle East & Asia Pacific Regions
800-366-2283
The shipping carton is the safest container in which the unit may
be transported. Save it for possible future use.
For additional information, see www.boschsecuritysystems.com
4
3 INSTALLATION
CAUTION: DO NOT EXCEED 30 VAC INPUT ON 24 VAC
MODELS. OPERATION ABOVE 30 VAC VIOLATES LOW
VOLTAGE OPERATION (CLASS 2 SPECIFICATIONS).
NORMAL OPERATION IS 24 VAC.
CUL APPROVED 24 VAC MODELS.
THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED SERVICE PERSON AND CONFORM TO ALL LOCAL
CODES.
CAUTION: CONNECT TO CLASS 2 POWER SUPPLY
ONLY. TOTAL CURRENT THROUGH ELECTRICAL
CONNECTOR IS 4 A MAXIMUM. PAN/TILT CURRENT IS
1 A MAXIMUM. ALLOWABLE CAMERA/HOUSING IS 3 A
MAXIMUM. USE ONLY 24 VAC CAMERAS AND HOUSINGS ON FEED-THRU MODELS.
ALWAYS DISCONNECT POWER TO UNIT AT CONTROLLER PRIOR TO CONNECTING OR DISCONNECTING PAN/TILT ELECTRICAL CONNECTOR. PAN/TILT TO
BE MOUNTED AWAY FROM UNAUTHORIZED ACCESS
[3 METERS (10 FEET) HIGH MINIMUM]
THESE UNITS ARE DESIGNED FOR EITHER UPRIGHT OR
INVERTED INSTALLATIONS. TO MAINTAIN WEATHERPROOF INTEGRITY WHEN MOUNTING OUTDOORS IN
AN INVERTED POSITION, THE UNIT MUST BE
INSTALLED IN A WEATHERPROOF ENCLOSURE (E.G.,
WEATHERPROOF DOMED HOUSING) OR A PROTECTED OUTSIDE AREA.
Pan/tilts and associated equipment should be tested prior to field
installation to verify proper wiring and operation of components.
LTC 9418 & LTC 9420
The maximum load is 10kg (22lb) or 149kg-cm (129lb-in) torque at
a distance of 63.5mm (2.5in) from the center of mass of the camera/lens/housing assembly to the center of the tilt table.
3.2
Recommended Mounting Equipment
LTC 9216/00 Medium duty wall mount designed to support up
to 45.3kg (100lb).
LTC 9222/00 Heavy duty wall mount designed to support up to
90.6kg (200lb).
LTC 9214/00 Heavy duty 336mm (14 inch) column mount for
ceiling or pedestal.
LTC 9224/00 Heavy duty 610mm (24 inch) column mount for
ceiling or pedestal use.
3.3
Wall Mounting
Follow the instructions provided with mounts. Mount and mounting
surface must be able to support the weight of the pan/tilt,
camera/lens, and enclosure (if used). The camera/lens/enclosure
must be properly mounted and balanced on the pan/tilt bracket.
LTC 9440 & LTC 9441
The maximun load is 18kg (40lb) or 297kg-cm (260lb-in) torque
with center of mass located 3.12in (79.2mm) from the center of the
titl table.
The combined weight of the enclosure/camera/lens should be centered equally, front to back, on the tilt table surface for best
pan/tilt operation.
3.4
Camera/Lens/Enclosure Mounting
Mount the camera/lens/enclosure to the pan/tilt bracket as follows:
SEE RECOMMENDED APPLICATIONS.
1.
3.1
CAUTION: THE PAN/TILTS IN THIS MANUAL CAN
ONLY BE MOUNTED UPRIGHT OR INVERTED; NEVER
HORIZONTALLY.
Model Designation
LTC 9418 Series
Load Rating:
22lb Load (10Kg), 129lb-in (149kg-cm) torque
Wiring: Standard
Power Required:
24W
LTC 9420 Series Load Rating:
22lb Load (10Kg), 129lb-in (149kg-cm) torque
Wiring: Feed-thru
Power Required:
24W
LTC 9440 Series Load Rating:
40lb Load (18kg), 260lb-in (297kg-cm) torque
Wiring: Standard
Power Required:
20W
LTC 9441 Series
Load Rating:
40lb Load (18kg), 260lb-in (297kg-cm) torque
Wiring: Feed-thru
Power Required:
20W
/60 models*:
/20 models*:
* 40lb Models
/10 models:
/50 models:
Rated Motor Voltage
Voltage Range
120VAC, 60Hz
24VAC, 60Hz
108 to 132
21.6 to 26.4
24VAC, 60Hz
23 to 26.4
24VAC, 50Hz
220VAC, 50Hz
21.6 to 26.4
207 to 253
2.
Balance the camera/lens/enclosure and adjust the unit to align
with mounting holes. Fasten with a minimum of two (2) 1/4-20
x 1/2-inch long fasteners and lock washers.
Make all electrical connections. Leave sufficient loops of cable
between camera/enclosure and pan/tilt to allow for tilting and
panning.
Pan Range: 00 to 3450 on standard models, 00 to 3600 on
Continuous Pan models. Pre-position is designated as -/x1, e.g.,
LTC 9441/61
5
3.5
Electrical Connections
1. Cable must be wired according to Connector Assembly
(Section 3.7) and Recommended Maximum Cable Lengths
(Table 1).
2. Use separate shielded cables for camera power, enclosure
power, and pan/tilt control. If required, combining lens control
wiring and video coax within a common cable is acceptable.
The use of a common multiconductor cable to combine all
functions is not recommended.
3. Use color coded conductors to aid wiring and future identification.
4. Retain wiring diagram for later reference.
Model
Voltage
Wire Size
mm2
AWG
Distance1
Feet
Meters
24 VAC2
0.5
1
1.5
2.5
4
0.5
1
1.5
2.5
0.5
1
1.5
2.5
140
230
360
590
940
2200
3500
5500
9000
13400
21200
33300
54400
110 VAC
220 VAC
Table 1
20
18
16
14
12
20
18
16
14
20
18
16
14
43
70
110
180
287
671
1067
1677
2744
4085
6463
10152
16585
CAUTION: CONTACT REMOVAL FROM CONNECTOR
REQUIRES USE OF AMP #305183 EXTRACTION TOOL.
3.6
Grounding Connection
A ground screw is located on the base to the right of connector.
See Figure 8. Connect a 1 mm2 (No.18 AWG) ground wire to the
nearest earth ground.
3.7
Connector Assembly
A mating connector, sockets and a strain relief are included with
the unit. Refer to Figure 1.
To install, select the appropriate size strain relief clamp. Choose
one of the two strain relief clamps enclosed with the sleeve and the
extender. The clamping area is adjustable by inverting or changing
the strain relief clamps. Discard the four strain reliefs on the
carrier strip packaged with the shield.
Insert the clamp into the strain relief until it bottoms. The clamp
should bottom on the wire bundle, not on the shield’s shoulder. If
the wire diameter is too small, temporarily wrap the wire with electrical tape until proper clamping is obtained. Secure the clamp with
the two (2) screws provided.
CAUTION: MAKE SURE THE WIRE BUNDLE IS PROPERLY
SECURED. DO NOT PINCH THE WIRES.
Maximum Cable Lengths
Notes For Table 1
1. Values calculated at 20º C (68 ºF) using stranded tinned copper
wire, a common ground (neutral), and both PAN and TILT motors
operating simultaneously.
2. For 24 VAC Models operating at or near -30º C, values are
based upon maintaining the supplied voltage within the voltage
range as specified in Section 3.1.
Screws (2)
AMP Hand Crimping Tool #58495-1 is recommended for crimping
sockets. Refer to Figure 2 for the numbered connector
positions.The connector will accept up to a #16 AWG wire. If heavier gauge wire is required, pigtailing according to local electrical
codes is recommended.
Strain Relief Clamp
Strain Relief Slot
Shield
Washer
Wire Bundle
Strip Length
.156 ± .015
Sleeve
Contact
Extender
Connector
Figure 1: Shield/Strain Relief Assembly
6
WIRE DESIGNATION AND PIN CONNECTIONS
Figure 2: Pin Outs
345° Non-Pre-Position Models5,6
Feed -thru Wiring
Pin
1:
2:
3:
4:
5:
6:
7:
8:
9:
10:
11:
12:
13:
14:
15:
16:
17:
18:
19:
20:
21:
22:
23:
24:
Number
NC1
NC1
NC1
NC1
Lens Common
Zoom
Focus
Unused
Unused
Accessory
Accessory
Accessory
NC1
NC1
NC1
Pan Left
NC1
Pan Right
P/T Common
Tilt Up
Tilt Down
Ground
Camera AC-Line
Camera AC-Neutral
Color
Green2
Blue2
Violet2
Brown2
Black2
White2,3
Red2,3
Yellow2,3
White
Violet
Blue
Brown
White/Yellow
Green/Yellow2
Black2,4
White2,4
345° Pre-Position Models5,6
Feed-thru Wiring
Pin
1:
2:
3:
4:
5:
6:
7:
8:
9:
10:
11:
12:
13:
14:
15:
16:
17:
18:
19:
20:
21:
22:
23:
24:
Number
PP Supply (+)
Pan Position
PP Return (-)
Tilt Position
Lens Common
Zoom
Focus
Zoom Position
Focus Position
Accessory
Accessory
Accessory
NC1
NC1
NC1
Pan Left
NC1
Pan Right
P/T Common
Tilt Up
Tilt Down
Ground
Camera AC-Line
Camera AC-Neutral
Color
Orange2
Yellow2
Gray2
White/Black2
Green2
Blue2
Violet2
Brown2
Black2
White2,3
Red2,3
Yellow2,3
White
Violet
Blue
Brown
White/Yellow
Green/Yellow2
Black2,4
White2,4
345° Non-Pre-Position Models5,6
Standard Wiring
Pin Number
1: NC1
2: NC1
3: NC1
4: NC1
5: NC1
6: NC1
7: NC1
8: NC1
9: NC1
10. NC1
11. NC1
12. NC1
13: NC1
14: NC1
15: NC1
16: Pan Left
17: NC1
18: Pan Right
19: P/T Common
20: Tilt Up
21: Tilt Down
22: Ground
23: NC1
24: NC1
Color
White
Violet
Blue
Brown
White/Yellow
Green/Yellow2
345° Pre-Position Models5,6
Standard Wiring
Pin Number
1: PP Supply (+)
2: Pan Position
3: PP Return (-)
4: Tilt Position
5: NC1
6: NC1
7: NC1
8: NC1
9: NC1
10. NC1
11. NC1
12. NC1
13: NC1
14: NC1
15: NC1
16: Pan Left
17: NC1
18: Pan Right
19: P/T Common
20: Tilt Up
21: Tilt Down
22: Ground
23: NC1
24: NC1
Color
Orange2
Yellow2
Gray2
White/Black2
White
Violet
Blue
Brown
White/Yellow
Green/Yellow2
7
360° Pre-Positions and
Non Pre-position Models7,8
Pin Number
1: Pan +5V
2: Pan Sense (3)
3: Pan-5V
4: Tilt Sense
5: Lens Common
6: Zoom
7: Focus
8: NC1
9: NC1
10. Accessory
11. Accessory
12. Accessory
13: NC1
14: NC1
15: Pan Sense (2)
16: Pan Left
17: NC1
18: Pan Right
19: P/T Common
20: Tilt Up
21: Tilt Down
22: Ground
23: Camera AC-Line
24: Camera AC-Neutral
Color
Orange8
Wht/Blk/Yel8
Wht/Blk/Red8
Wht/Blk/Brn8
Green2
Blue2
Violet2
White2,3
Red2,3
Yellow2,3
White/Orange8
White
Violet
Blue
Brown
White/Yellow
Green/Yellow2
Black2,4
White2,4
Notes
1. NC -- No Connection, do not use.
2. (Color Codes) indicate feed-thru wiring to
camera/housing.
3. Apply to 24 volt models only. Pins 10 thru
12 are not used in 110 volt or 220 volt models.
4. (Color Codes) shown are for 24 volt,
60 HZ and 110 volts models. For 220 volt
and 24 volt, 50 HZ models, color codes are
(23) Brown, and (24) Blue.
5. The conductors for pins 16 thru 24 (where
applicable) on 220 volt models should be
isolated from other wiring with reinforced
insulation requirements of DIN VDE
0860/05.89, IEC 65. The conductors for
pins 16 thru 24 (where applicable) must be
in HAR cord minimum cross sectional area
0.75 mm2 (H05 VV-F).
6. Refer to Figure 6 for the wiring
schematic.
7. Refer to Figure 7 for the wiring
schematic.
8. Pre-Position models only. Refer to Figure
8 for the wiring schematic.
3.8
Pan Stops (345° Models)
Locate the three (3) limit stops on the base of the unit. The red
limit stop is the Fixed Stop. It is not adjustable and should not be
removed. The remaining two (2) stops are called Pan Stops. These
are positioned on each side of the pan switch lever.
The two (2) pan stops are adjustable and secured with a set screw.
The screws can be accessed through the hole in the end of each
stop. Use a 3/32-inch Allen wrench (supplied) to loosen and tighten the set screw. See Figure 3.
4.2
Auto-Pan Operation (345º Models)
Use of the auto-pan function requires wiring connections to pin 16
(Pan Left), pin 18 (Pan Right), and pin 19 (Common). See Figure 6.
The auto-pan function is achieved by the controller unit sensing
changes in current flow through the pan motor. When a pan stop is
reached, the current flow stops and internal circuitry of the controller unit reverses the auto-pan direction.
Note: The pan/tilt controller must be equipped with special current
sensing circuitry to operate the auto-pan function in this mode. The
pan stops or the fixed stop establish the limits for auto-pan.
Top View Of Base
Front
Top View Of Base
Front
Left
(CCW)
Pan
Stops
Right
(CW)
Fixed Stop (Red)
Pan Stops
Removed
Rear
Fixed Stop
(Red)
Figure 3: Pan Stop Locations (345º Models)
Figure 4: Maximum Manual Pan and Maximum
Auto-Pan (345º Models)
4 OPERATION
4.1
4.3
Manual Pan Operation (345° Models)
The pan stops establish the limits for manual pan. The two (2)
adjustable pan stops may be repositioned or removed depending
on the desired operation. The maximum pan range setup is shown
in Figure 4.
CAUTION: NEVER MOVE OR REMOVE THE FIXED STOP. IT
MUST ALWAYS BE IN PLACE FOR PROPER OPERATION OF
THE PAN FUNCTION.
1.
2.
3.
Pan Stop Adjustment (345° Models)
Loosen the pan stops and adjust to the desired range for
manual pan and auto-pan. A recessed area in the pan head
allows enough clearance to remove a stop from the base.
When all the stops are in place, check to see that they are
secure.
Operate the unit from the controller to confirm that the limits
are set properly. Readjust if required.
4.4
Pan Operation (360° Models)
These models allow 360 degree rotational (pan) operation. They
have no pan stops. These units can be manually panned left or
right or they can be panned continuously left or right by auto-pan
activation. Auto-Pan activation requires wiring connections to pin
16 (Pan Left), pin 18 (Pan Right), and pin 19 (Common). See
Figure 7.
8
4.5
Tilt Stop Adjustment (All Models)
After the unit is installed and all wire connections are made, apply
proper power to the control unit. Refer to Figure 5, and adjust the
tilt stops as follows:
1.
2.
3.
4.
With the front of the pan/tilt facing you, remove the left hub
cap. The tilt stop adjustment screws are now exposed.
Using the control unit, tilt the bracket up to the desired position and stop the unit. Use the 3/32-inch Allen wrench to
loosen the Tilt Up stop. Slide the stop Up until a faint click is
heard (indicating switch actuation). Tighten the Tilt Up limit
stop screw.
Using the control unit, tilt the bracket to the desired position
and stop the unit. Use the 3/32-inch Allen wrench to loosen
the Tilt Down stop. Slide the stop Down until a faint click is
heard. Tighten the Tilt Down limit stop screw.
Operate the control unit to verify proper tilt stop range and
operation. Repeat above sequence if necessary. Make certain
both tilt stop screws are snug. Replace the hub cap.
CAUTION: DO NOT OPERATE PAN/TILT UNIT WITHOUT
STOPS. LIMIT STOPS SHOULD NOT BE ADJUSTED
WHILE UNIT IS OPERATING.
REAR
Tilt Down (CW) Stop
FRONT
Tilt Up (CCW) Stop
Figure 5: Tilt Stops (Side View - Plug Removed)
4.6
Pre-Position Models
The 345° models with pre-position capability require wiring
connections to pins 1 through 4, 8 and 9, and use of a controller or
receiver/driver with the pre-position function. Pan and tilt operation
and limit stop adjustments function the same as the previous models
described.
9
5
WIRING DIAGRAMS
Figure 6: Wiring Diagram - 0º to 345º Models
10
Video
Figure 7: Wiring Diagram - 360º Models
11
Video
Control
Figure 8 - 360º Models with Pre-Position
12
6 RECOMMENDED APPLICATIONS
360° Models Only
Feed-thru 24 Volt Models
USE ONLY 24 VOLT CAMERAS/HOUSINGS WITH 360° MODEL
PAN/TILTS.
TO MAINTAIN CUL AND TUV APPROVAL, USE ONLY 24 VOLT
CAMERAS/HOUSINGS.
THE MAXIMUM POWER FOR HEATER/BLOWER COMBINATIONS IS 75 WATTS TO PREVENT OVERLOADING
THE SLIP RING. THIS LOAD MUST BE POWERED BY PIN
10, (WHITE FEED-THRU) AND PIN 11 (RED FEED-THRU).
SEE FIGURE 2.
7 DIMENSIONAL OUTLINE
Figure 9
13
This page intentionally left blank
14
This page intentionally left blank
15
Bosch Security Systems, Inc.
850 Greenfield Road
Lancaster, PA 17601 EE.UU.
Tel: 800-326-3270
Fax: 717-735-6560
www.boschsecuritysystems.com
Robert Bosch GmbH
Geschäftsbereich
Postfach 10 60 50
70049 Stuttgart
Telefax (0711) 811-1234
@ 2003 Bosch Security Systems GmbH
100 0083 001 BOS
08/03 Data subject to change without notice.
Bosch Security Systems B.V.
P.O. Box 80002
5600 JB Eindhoven
The Netherlands
Tele +31 40 27 80000