Combo heat press machine Instruction

Combo heat press machine
Instruction
Pressing Technique
Voltage: 220V/110V
Maximum power: 1800W
Temperature: 0-250℃
Time: 0-3minutes
Introduction
①:Clamp&handle
②:Pressure Knot
③:Control console
④:Fuse
⑤:Off/on Switch
⑥:connect power cord
⑦:The anti swivel locks.
⑧: Swing nut (Function: It is used to adjust
the swing breadth)
Installation
1.Assemble power connector
There is a slot in the connector
Aiming at the slot, insert the connector to
the connect power cord
Screw the screw cap
2. How to offload the heat platen from the main body?
A、Offload the up-heat platen
Draw down the handle
Get off the whorl
Let the handle down freely
Pull up the handle and move it to the side
Screw the nail under the handle
counter-clockwise
Bring up the heat platen directly
Get off the whorl
Pull up the handle
Use the spanner
To hold the screw by hand
Release the screw anticlockwise
Bring up the heat platen directly
B. Offload the down-heat platen
There are two whorls in the base
Screw it off counter- clockwise
Bring up the down-platen directly
3. Install Plate press attachment
The end with wire of the plate platen
towards the machine
Aim at the fastener under the handle
Push the platen to the end, no need to
lock screw cap, since it is with magnet.
4. Install Cap press attachment
The longer end of the base towards to
the machine
Aim at the whorl and place it on the
machine foundation
Let the end with wire of the cap heat
platen forward
Aim at the slot and push it till the end
Lock the screw cap (clockwise)
Lock the screw cap(clockwise)
5. Install Mug press attachment
No need offloading or installation
the mug press attachment
Operation
Connect the power connector of the mug
press attachment to the main machine
Process
The operation of the control panel
1. Set temperature required
Then it is ready to use.
Turn on power switch,
Temperature light – ON
Select with arrows temperature required (normally 180℃)
Left arrow select up. Right arrow select down
2. Set time required
Press OK button after temperature set,
now timer light-ON
Select with arrows temperature required
Left arrow select up. Right arrow select down
The unit is second, time range: 0-180 seconds
3. Printing methods:
1) Heat Press Techniques: Place the object (i.e. T-shirt) on press bed, adjust pressure to your requirement, and turn on
the power switch ON, The temperature starts to rise, once the temperature rise to the required temperature, the
buzzer will send out a short sound. Then press object. Push the OK button once, wait for long buzzer sound, turn off
the power switch, work finish and take out object.
4. Recommendations:
1) Ceramic tile transfer: (Mugs & Plates transfer is similar)
Parameter: temperature: 180℃.
The time of press: 15 seconds
2) T-shirt transfer:
Parameter: temperature: 180℃.
The time of press:( chemical fiber use for sublimation transfer paper: 30-50seconds; pure cotton use for T-shirt
transfer paper: 10-20seconds)
3) Cap pressing
Unscrew the press bed and fit cap press bed onto the base of the heat press machine by using the wing nuts
Change press head
Adjust height and lock the anti swivel locks of the heat press machine by using the black knob at the back of machine.
Before you switch machine ON make sure element wire is plugged in and secured and all components has been
secured and fastened REMEMBER to unlock anti swivel lock before adjusting the pressure.
Trouble shooting for transfer quality:
A. If the color is pale: the temperature is too low / the pressure is not correct / or not pressed long enough.
B. If the picture is blurring: Too much tranfer time causes proliferation.
C. If a part of picture is blurring: Heat was not distributed correctly through heat plate. Allow more time between press
operations. Pressure distribution can also be the cause, which can be set on the four plate surface adjusters. Please note
that it has been factory set and there should be no need to adjust them
D. If the pattern is scarred: Transfer time is too long.
E. The pattern of color is different: the pressure is not correct or the transfer paper is poor quality
F. Adhesive paper: the temperature is too high or poor printing ink
Circuit Diagram:
a:PCB
b:Switch
c:Fuse
d: Aerial Plug
e: Relay
PCB Definition:
1,2
Electrical source tie-in;
3,4
Radiation pipe tie-in;
5,6
Sensor tie-in;
7,8
Relay output tie-in;
9,10
Relay input tie-in
Maintenance:
Ⅰ. No action after switch on the power
1. Check the plug whether it touchs well
2. Check the fuse whether it have been burn out.
3. Check the lead wire of the switch whether it have been fallen
Ⅱ. The display screen are working well, but the no temperature increasing on the Silica Gel Board
1. Check whether the tie-in of the Silica Gel touches well.
2. Check the 3,4 on PCB in the back box whether it touches well.
Ⅲ. The display screen is un-normal, but the Silica Gel heats.
Maybe for the fault of the PCB
Ⅳ. The display screen and Silica Gel works well, but un-normal show of the temperature.
1. Check whether the tie-in of the Silica Gel touches well.
2. Check the 5, 6 on PCB in the back box whether it touches well.
Advise: 1. Because the material and the thickness of the clothing are different, the temperature and
the time are different too.
2. The temperature and the time are only for reference. And pls first try a sample to adjust the
best temperature and time.
3. The best setting temperature are 180℃, pls do not over 220℃, and the transferring time
should be within 3 minutes.
4. To make sure that the circuit can bear high-power machine, or it will bring about faulty of the
fuse etc.