SPECIAL THANKS
Dear Valued Customer,
Thank you for choosing Diamond Audio D6 speakers. These speakers represent the latest
advances in acoustic technology, and like all Diamond Audio products, are hand built and tested
using the highest grade components and state of the art techniques. When installed properly, they
will provide many years of accurate sound reproduction.
Please keep in mind that prolonged exposure to sound pressure levels in excess of 100 dB can
cause permanent hearing loss. This high performance speaker system can exceed that level, so
please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity in the
future.
Because of their flexible installation possibilities, please consider having your new speakers
professionally installed by an authorized Diamond Audio dealer. This will assure a clean and
efficient installation, and extend your one year warranty to two years.
At Diamond Audio, we strive to bring honest value and excellent quality to all of the products we
build. By your purchase of this product, you have joined the growing family of discerning listeners
who demand only the best. Welcome!
2
©2011 Diamond Audio Technologies. All rights reserved.
FEATURES
• Hard Anodized Aluminum Cones
• Rubber Surrounds
• Proprietary Composite Frames
• Flat Progressive Spider
• Extended Pole Motor Design
• Rubber Boot Magnet Protector
• Model Specific Crossovers
• Shallow Mount
Programmable Crossovers
Each 06 convertable speaker features a 12 dB/octave crossover and tweeter protection to ensure
absolute fidelity and protection during audio reproduction.
Standard Connection
06 integrated systems are shipped configured for a single channel per speaker. Simply connect the
speaker wire from the source to the exposed positive and negative terminals on the speaker.
3
©2011 Diamond Audio Technologies. All rights reserved.
PARTS LIST
D663A/S D673A/S
(2)
(2)
(2)
(2)
(1)
06 Convertable Speakers
06 Model Specific Crossovers
06 Grills w/ Mounting Ring (except for 0673)
Mounting Gaskets
Mounting Hardware Kit
MID-BASS SPEAKER MOUNTING
The illustration below shows the parts included and correct mounting assembly of the 06
integrated and component mid-bass drivers. Mounting ring and grill are optional.
Gasket
,
I
Mounting Screws
'
~
Screw Clips
@
4
©2011 Diamond Audio Technologies. All rights reserved.
Grill
Convertable Tweeter Removal
Detach tweeter wires form
terminals. Grasp tweeter firmly.
Twist until tweeter detaches from
mount. Pull tweeter assembly and
wires free from speaker. Screw
bullet shaped phase plug firmly
onto tweeter mount.
Tweeter Mounting
When flush or surface mounting tweeters, make sure the desired location can
accommodate the hole size and depth required. Mount the cup using provided hardware
(flush mount illustration shown) Mount surface cup at desired angle with provided screws
in tweeter mounting kit. Snake speaker wires through tweeter cup, connect tweeter to
wires, and snap tweeter into cup by aligning the notches. Be careful not to push on the
center of the tweeter grill.
1.6" Diameter
Mounting Cup
r~
II'
'II
I
I
Clamp Ring
Tweeter
5
©2011 Diamond Audio Technologies. All rights reserved.
COMPONENT SYSTEM CONNECTION
The illustration below shows how to connect one channel of the 06 component system.
Mid-bass Driver
Crossover
Crossover Programming
Each 06 component set comes with a pair of model specific programmable crossovers.
Under the cover there is a jumper marked PHASE 0- 180. Tweeter phase can be changed
by moving the jumper to the appropriate position. The adjustment of tweeter phase is
intended to improve frequency response in the case that the tweter is off axis with the
listener or seperated from the midrange by a significant distance.
RAF Outputs
Each 06 component crossover has a third set of outputs marked "RAF". This stands for
Rear Acoustic Fill. This output can be used to power an additional speaker off the same
channel without affecting the impedance load on the source unit. This output provides 15200/o of the total power to the extra speaker and is unfiltered or full range.
6
©2011 Diamond Audio Technologies. All rights reserved.
THIElE/SMAll PARAMETERS
Parameter (unit)
D663A/S
D673A/S
Sensitivity@ 2.83V
91.3
90.1
Qts
1.06
Fs (Hz)
0.68
60.0
Vas (L)
15.6
Re (ohm)
3.6
3.0
Xmax (mm)
Impedance (ohm)
4
75/150
Power Nom/Max (Watts)
76.0
10.3
3.5
4.0
4
60/120
PHYSICAl DIMENSIONS
Dimension
Unit
D663A/S
D673A/S
Total Diameter
(A)
in.
mm
6.51"
165.4
5.53" X 8.65"
140.5 X 219.7
5.53"
140.6
6.92" X 4.95"
175.8" X 125.7"
6.14"
156.0
8.03" X 4.98"
203.9 X 126.5
2.32"
59.0
2.25"
57.2
3.40"
86.4
3.07''
78.0
Mounting Diameter
(B)
mm
Hole Diameter
(C)
mm
Mounting Depth
(D)
mm
Magnet Diameter
(E)
mm
in.
in.
in.
in.
(C)
0
1 4 - - - - - - - - - (8)---~
7
©2011 Diamond Audio Technologies. All rights reserved.
LIMITED SPEAKER WARRANTY STATEMENT
Diamond Audio Technologies, LLC (OAT) warrants this product to be free from defects in material and workmanship for a
period of one (1) year from the original date of purchase provided it was purchased from an authorized OAT retailer within
the United States. However, if this product was installed by the authorized OAT retailer, the warranty period will be extended
to two (2) years.
THIS WARRANTY IS NOT TRANSFERABLE AND APPLIES ONLY TO THE ORIGINAL PURCHASER OF THIS PRODUCT
IN ITS ORIGINAL INSTALLATION. Original purchaser must reside in the United States and be able to provide proof of
purchase and installation with the sales receipt from the authorized OAT retailer that sold and installed the product.
Should a manufacturing defect occur during above said warranty period, OAT will replace or repair the defective product
with a product of the same or equivalent value and performance.
Damage or failure caused by any of the following is not covered under this warranty policy: negligence, improper use,
abuse, product modification, unauthorized repair attempts, accident, acts of God, misrepresentations by OAT retailers, and
improper/inadequate packaging during return shipping.
Warranty is void if serial numbers have been removed, altered or defaced.
HOW TO OBTAIN WARRANTY SERVICE
In the event a OAT product should require service, you should visit the authorized OAT retailer you purchased the product
from and they can expedite your claim. All claims must fall into the guidelines listed above and be accompanied by a copy of
the original sales and installation receipt from that authorized OAT retailer.
Product returned for warranty service must be freight-prepaid, properly packaged and clearly marked with the Return
Authorization (RA) number issued by OAT. Any product returned to DAT that is improperly packaged, does not have a
RA number clearly marked on the package, or never received a RA number may be refused upon delivery. DAT does not
assume responsibility for lost or misdirected product.
Repair or replacement under this warranty is the exclusive remedy of the consumer. OAT shall not be liable for any
incidental or consequential damages for breach of any expressed or implied warranty on this product. Some states do not
allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how long an implied warranty
lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may
also have other rights that may vary from state to state.
Customers outside the United States should contact their local sales office to obtain information on pricing, exchange unit
availability, instructions, service and warranty/non-warranty replacement or repair.
Diamond Audio Technologies
DIANIOND
6915 West Frye Road
Chandler, AZ 85226 USA
Tel: 480.820.2075
Fax: 480.813.6210
Web: diamondaudio.com
Service/Tech Support:
480.820.2075
Tech Support Email
techsupport@diamondaudio.com
©2011 Diamond Audio Technologies. All rights reserved.
071911