Epson | PowerLite Home Cinema 3020 | User`s guide | Epson PowerLite Home Cinema 3020 User`s guide

PowerLite Home Cinema 3020
®
Quick Setup
Turn on your equipment
Before using the projector, make sure you read the safety instructions in the
online User’s Guide.
1
Turn on your video source or computer.
2
Plug in the projector. The
Viewing 3D images
4Turn the focus ring to sharpen the image.
To view 3D content, you must first connect a 3D-compatible video device to
one of the HDMI ports on your projector. You will also need a pair of EPSON
or EPSON-compatible RF 3D active shutter glasses.
power button on the projector turns blue.
Choose a location
Keep the projector level and place it at a height so its lens is even with the top
or the bottom of the screen and is centered horizontally. If this isn’t possible,
use the horizontal keystone slider and keystone correction buttons to reposition
the image (see “Adjust the image”).
In order to view 3D images correctly, 3D glasses must be worn within 32 feet
(10 m) of the projector. Use the image below to determine the viewing distance
for 3D projection (the shading represents the 3D viewing area):
5If your image looks like
or
, you’ve placed the projector off to
one side of the screen at an angle. Place the projector directly in front of
the center of the screen, facing the screen squarely. Or use the horizontal
keystone slider on the projector to correct it.
3
1
Turn on and begin playback on the 3D-compatible video device.
2
Press the
button on the projector remote control, if necessary.
3Slide the power switch on your 3D glasses to the On position.
Remove the lens cap.
4Press the
power button on the projector or the On button on the
remote control. The power light flashes blue, and then stays on.
6Your projector automatically adjusts images that look like
but if necessary you can press the
correct this.
or
or
,
buttons on the projector to
Note: If the glasses don’t automatically display 3D content, you may
need to pair them with the projector. Move the glasses within 10 feet
(3 m) of the projector, then press and hold the Pairing button on the
3D glasses for at least 3 seconds. The status light on the glasses will
alternately flash green and red, then remain green for 10 seconds if
pairing is successful.
Using the remote control
Make sure the batteries are installed as shown (two AA batteries).
See the online User’s Guide for more information on where to place your
projector.
Connect the projector
Choose from the following connections. For additional connection types, see
the online User's Guide.
See the online User’s Guide for more information on adjusting the 3D images.
power button on the
projector twice or the Standby button on the remote control, then
unplug it. You don’t have to wait for the projector to cool down.
HDMI cable
RCA video cable
Audio cable
Component video cable
If you see a blank screen or the No signal message after turning on your
video device or computer, check the following:
5The default language of the menu system is English. To select another
language, press the Menu button on the remote control. Select Extended
and press Enter. Select Language and press Enter. Select your language
and press Enter. Press the Menu button to exit the menu system.
Video Device
Connect up to 5 video devices and use the Source buttons on the projector or
remote control to switch between them.
Troubleshooting
Note: To shut down the projector, press the
•Make sure the power light on the projector is blue and not flashing.
Turn projector on
select the image source on the remote control.
Navigate projector
menus
Audio cable
For more information on using the remote control, see the online User’s Guide.
*412371600*
*412371600*
•
If you’re using a Windows® laptop, press the function key on your
keyboard that lets you display on an external monitor. It may be labeled
CRT/LCD or have an icon such as
. You may have to hold down the
Fn key while pressing it (such as Fn + F7). Wait a moment for the display
to appear.
•
If you’re using a Mac laptop, open System Preferences and select
Displays. Select the VGA Display or Color LCD option if necessary,
then click the Arrange or Arrangement tab, and select the Mirror
Displays check box.
Access projector
menus
Turn off projector
display
3
Press the Source buttons on the projector or the remote control to
switch to the correct image source, if necessary.
Switch between
2D and 3D
Note: If you still see a blank screen or have other display problems, see
the troubleshooting tips on the front of this sheet.
2To raise the image, adjust the front feet as shown below.
•
Choose which source
to display
Adjust the image
1If you don’t see an image, press the Source buttons on the projector or
Turn projector off
If 3D images aren’t displaying properly, check the following:
•
Press the
•
Make sure that you are within the 3D viewing range. See “Choose a
location” or the online User’s Guide for more information.
•
Press the Menu button on your remote control, select the Signal menu,
then 3D Setup, then select 3D Format. Make sure that the Auto option is
selected.
•
Check that your video device and media are both 3D-compatible. Refer
to the documentation that came with your video device for more
information.
Turn the zoom ring to reduce or enlarge the image.
button to switch to 3D viewing mode, if necessary.
PowerLite Home Cinema 3020
®
Quick Setup
Turn on your equipment
Before using the projector, make sure you read the safety instructions in the
online User’s Guide.
1
Turn on your video source or computer.
2
Plug in the projector. The
Viewing 3D images
4Turn the focus ring to sharpen the image.
To view 3D content, you must first connect a 3D-compatible video device to
one of the HDMI ports on your projector. You will also need a pair of EPSON
or EPSON-compatible RF 3D active shutter glasses.
power button on the projector turns blue.
Choose a location
Keep the projector level and place it at a height so its lens is even with the top
or the bottom of the screen and is centered horizontally. If this isn’t possible,
use the horizontal keystone slider and keystone correction buttons to reposition
the image (see “Adjust the image”).
In order to view 3D images correctly, 3D glasses must be worn within 32 feet
(10 m) of the projector. Use the image below to determine the viewing distance
for 3D projection (the shading represents the 3D viewing area):
5If your image looks like
or
, you’ve placed the projector off to
one side of the screen at an angle. Place the projector directly in front of
the center of the screen, facing the screen squarely. Or use the horizontal
keystone slider on the projector to correct it.
3
1
Turn on and begin playback on the 3D-compatible video device.
2
Press the
button on the projector remote control, if necessary.
3Slide the power switch on your 3D glasses to the On position.
Remove the lens cap.
4Press the
power button on the projector or the On button on the
remote control. The power light flashes blue, and then stays on.
6Your projector automatically adjusts images that look like
but if necessary you can press the
correct this.
or
or
,
buttons on the projector to
Note: If the glasses don’t automatically display 3D content, you may
need to pair them with the projector. Move the glasses within 10 feet
(3 m) of the projector, then press and hold the Pairing button on the
3D glasses for at least 3 seconds. The status light on the glasses will
alternately flash green and red, then remain green for 10 seconds if
pairing is successful.
Using the remote control
Make sure the batteries are installed as shown (two AA batteries).
See the online User’s Guide for more information on where to place your
projector.
Connect the projector
Choose from the following connections. For additional connection types, see
the online User's Guide.
See the online User’s Guide for more information on adjusting the 3D images.
power button on the
projector twice or the Standby button on the remote control, then
unplug it. You don’t have to wait for the projector to cool down.
HDMI cable
RCA video cable
Audio cable
Component video cable
If you see a blank screen or the No signal message after turning on your
video device or computer, check the following:
5The default language of the menu system is English. To select another
language, press the Menu button on the remote control. Select Extended
and press Enter. Select Language and press Enter. Select your language
and press Enter. Press the Menu button to exit the menu system.
Video Device
Connect up to 5 video devices and use the Source buttons on the projector or
remote control to switch between them.
Troubleshooting
Note: To shut down the projector, press the
•Make sure the power light on the projector is blue and not flashing.
Turn projector on
select the image source on the remote control.
Navigate projector
menus
Audio cable
For more information on using the remote control, see the online User’s Guide.
*412371600*
*412371600*
•
If you’re using a Windows® laptop, press the function key on your
keyboard that lets you display on an external monitor. It may be labeled
CRT/LCD or have an icon such as
. You may have to hold down the
Fn key while pressing it (such as Fn + F7). Wait a moment for the display
to appear.
•
If you’re using a Mac laptop, open System Preferences and select
Displays. Select the VGA Display or Color LCD option if necessary,
then click the Arrange or Arrangement tab, and select the Mirror
Displays check box.
Access projector
menus
Turn off projector
display
3
Press the Source buttons on the projector or the remote control to
switch to the correct image source, if necessary.
Switch between
2D and 3D
Note: If you still see a blank screen or have other display problems, see
the troubleshooting tips on the front of this sheet.
2To raise the image, adjust the front feet as shown below.
•
Choose which source
to display
Adjust the image
1If you don’t see an image, press the Source buttons on the projector or
Turn projector off
If 3D images aren’t displaying properly, check the following:
•
Press the
•
Make sure that you are within the 3D viewing range. See “Choose a
location” or the online User’s Guide for more information.
•
Press the Menu button on your remote control, select the Signal menu,
then 3D Setup, then select 3D Format. Make sure that the Auto option is
selected.
•
Check that your video device and media are both 3D-compatible. Refer
to the documentation that came with your video device for more
information.
Turn the zoom ring to reduce or enlarge the image.
button to switch to 3D viewing mode, if necessary.
Where to get help
Caution: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
Manual
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
For more information about using the projector, click the icon on your desktop
to access the online manual (requires an Internet connection). If you don’t
have a User's Guide icon, you can install it from the projector CD or go to the
Epson website, as described below.
Telephone support services
To use the EPSON PrivateLine Support service, call (800) 637-7661. This service
is available 6 am to 8 pm, Pacific Time, Monday through Friday, for the duration
of your warranty period.
®
®
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
Canada
Contains IC: 1052D-E207
This Class B digital apparatus complies with Canadian ICES-003.
You may also speak with a support specialist by calling (562) 276-4394 (US) or
(905) 709-3839 (Canada), 6 am to 8 pm, Pacific Time, Monday through Friday,
and 7 am to 4 pm, Pacific Time, Saturday.
This device complies with RSS-210 of the Industry Canada Rules. Operation
is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Days and hours of support are subject to change without notice. Toll or long
distance charges may apply.
Radiation Exposure Statement:
Internet support
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
Visit www.epson.com/support (U.S.) or www.epson.ca/support
(Canada) for solutions to common problems. You can download utilities and
documentation, get FAQs and troubleshooting advice, or e-mail Epson.
Declaration of Conformity
Registration
Register today to get product updates, special promotions, and customer-only
offers. You can use the CD included with your projector or register online at
www.epson.com/webreg.
Optional accessories
For a list of optional accessories, see the online User’s Guide.
You can purchase RF 3D glasses or other accessories from an EPSON authorized
reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you
can purchase online at www.epsonstore.com (U.S. sales) or www.epson.ca
(Canadian sales).
Notices
Bluetooth Safety and Specifications
Contains Bluetooth module model: DBUB-E207
This document provides safety instructions and describes the specifications.
Read this document carefully before use to ensure your safety and product
performance.
U.S.
Contains FCC ID: BKMAE-E207
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
Reorient or relocate the receiving antenna.
•�������������������������������������������
Increase the separation between the equipment and receiver.
•�����������������������������������������������������������
Connect the equipment into an outlet on a circuit different from that to
•�������������������������������������������������������������������������
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
•������������������������������������������������������������������
According to 47CFR, Part 2 and 15, Class B Personal Computers and Peripherals;
and/or CPU Boards and Power Supplies used with Class B Personal Computers
We:
Located at: Tel:
Epson America, Inc.
3840 Kilroy Airport Way
MS: 3-13
Long Beach, CA 90806
562-290-5254
Declare under sole responsibility that the product identified herein, complies
with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device. Each
product marketed, is identical to the representative unit tested and found
to be compliant with the standards. Records maintained continue to reflect
the equipment being produced can be expected to be within the variation
accepted, due to quantity production and testing on a statistical basis as
required by 47CFR 2.909. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Trade Name: EPSON
Type of Product: LCD Projector
Model:
H501A
Marketing Name:PowerLite Home Cinema 3020
Epson America, Inc. Limited Warranty
Two-Year Projector Limited Warranty, 90-Day Lamp Limited Warranty and
1-Year 3D Glasses Limited Warranty
the cost of a replacement projector in the event that you fail to return the
defective one. When Epson authorizes an exchange for defective 3D glasses,
you must first send in the defective glasses to Epson. Once we have received
your defective glasses Epson will ship a replacement product to you, freight
prepaid, so long as you use an address in the United States, Canada, or Puerto
Rico. If Epson authorizes repair instead of exchange, Epson will direct you to
send your product to Epson or its authorized service center, where the product
will be repaired and sent back to you. You are responsible for packing the
product and for all costs to and from the EPSON authorized service center.
When warranty service involves the exchange of the product or of a part,
the item replaced becomes Epson property. The exchanged product or part
may be new or refurbished to the Epson standard of quality, and at Epson’s
option, the replacement may be another model of like kind and quality. Epson’s
liability for replacement of the covered product will not exceed the original
retail selling price of the covered product. Exchange or replacement products
or parts assume the remaining warranty period of the product covered by this
limited warranty. If Epson replaces the lamp as part of the warranty service, the
replacement lamp carries the limited 90-day warranty stated above.
What This Warranty Does Not Cover: This warranty covers only normal use in
the United States, Canada or Puerto Rico. Twenty-four hours per day or other
excessive continual use is not considered normal use. This warranty does not
cover consumables such as filters. This warranty is not transferable. Epson is not
responsible for warranty service should the EPSON label or logo or the rating
label or serial number be removed. Epson is not responsible for warranty service
should the product fail to be properly maintained or fail to function properly
as a result of misuse, abuse, improper installation, neglect, improper shipping,
damage caused by disasters such as fire, flood, and lightning, improper
electrical current, software problems, interaction with non-EPSON products,
or service other than by Epson or an EPSON Authorized Servicer. Postage,
insurance, or shipping costs incurred in presenting your EPSON product for
carry-in warranty service are your responsibility. Epson will pay for all freight
charges if you choose to send your unit to Epson for repair. If a claimed defect
cannot be identified or reproduced in service, you will be held responsible for
costs incurred.
THE WARRANTY AND REMEDY PROVIDED ABOVE ARE EXCLUSIVE AND IN
LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE. SOME LAWS DO NOT ALLOW THE EXCLUSION OF
IMPLIED WARRANTIES. IF THESE LAWS APPLY, THEN ALL EXPRESS AND IMPLIED
WARRANTIES ARE LIMITED TO THE WARRANTY PERIOD IDENTIFIED ABOVE.
UNLESS STATED HEREIN, ANY STATEMENTS OR REPRESENTATIONS MADE BY
ANY OTHER PERSON OR FIRM ARE VOID. IN THE EVENT THE REMEDIES ABOVE
FAIL, EPSON’S ENTIRE LIABILITY SHALL BE LIMITED TO A REFUND OF THE
PRICE PAID FOR THE EPSON PRODUCT COVERED BY THIS LIMITED WARRANTY.
EXCEPT AS PROVIDED IN THIS WRITTEN WARRANTY, NEITHER EPSON AMERICA,
INC. NOR ITS AFFILIATES SHALL BE LIABLE FOR ANY LOSS, INCONVENIENCE,
OR DAMAGE, INCLUDING DIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES, RESULTING FROM THE USE OR INABILITY TO USE THE EPSON
PRODUCT, WHETHER RESULTING FROM BREACH OF WARRANTY OR ANY OTHER
LEGAL THEORY.
In Canada, warranties include both warranties and conditions.
What Is Covered: Epson America, Inc. (“Epson”) warrants to the original retail
purchaser of the EPSON projector product enclosed with this limited warranty
statement that the product, if purchased new and operated in the United
States, Canada, or Puerto Rico will be free from defects in workmanship and
materials for a period of two (2) years from the date of original purchase. This
limited warranty applies only to the projector and not to the projector lamp or
3D glasses. The projector lamp carries a limited warranty period of ninety (90)
days from the date of original purchase. The 3D glasses carry a limited warranty
period of one (1) year from the date of original purchase. For warranty service,
you must provide proof of the date of original purchase.
What Epson Will Do To Correct Problems: If your product requires service
during the limited warranty period, please call Epson at the number on the
bottom of this statement and be prepared to provide the model, serial number,
and date of original purchase. Epson will, at its option, repair or replace
the defective unit, without charge for parts or labor. If Epson authorizes an
exchange for the defective projector, Epson will ship a replacement projector
to you, freight prepaid, so long as you use an address in the United States,
Canada, or Puerto Rico. You are responsible for securely packaging the
defective unit and returning it to Epson within five (5) working days of receipt
of the replacement. Epson requires a debit or a credit card number to secure
Some jurisdictions do not allow limitations on how long an implied warranty
lasts and some jurisdictions do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitations and exclusions
may not apply to you. This warranty gives you specific legal rights, and you may
also have other rights, which vary from jurisdiction to jurisdiction.
To find the EPSON Authorized Reseller nearest you, please visit our website at:
www.epson.com.
To find the EPSON Customer Care Center nearest you, please visit
www.epson.com/support.
To contact the EPSON ConnectionSM, please call (800) 637-7661 or (562) 276-4394
in the U.S. and (905) 709-3839 in Canada or write to Epson America, Inc., P.O.
Box 93012, Long Beach, CA 90809-3012.
EPSON and PowerLite are registered trademarks, and EPSON Exceed Your Vision is a registered logomark of
Seiko Epson Corporation. PrivateLine is a registered trademark and EPSON Connection is a service mark of
Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks
of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2012 Epson America, Inc. 7/12
Printed in XXXXXX
CPD-37709
Where to get help
Caution: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
Manual
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
For more information about using the projector, click the icon on your desktop
to access the online manual (requires an Internet connection). If you don’t
have a User's Guide icon, you can install it from the projector CD or go to the
Epson website, as described below.
Telephone support services
To use the EPSON PrivateLine Support service, call (800) 637-7661. This service
is available 6 am to 8 pm, Pacific Time, Monday through Friday, for the duration
of your warranty period.
®
®
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
Canada
Contains IC: 1052D-E207
This Class B digital apparatus complies with Canadian ICES-003.
You may also speak with a support specialist by calling (562) 276-4394 (US) or
(905) 709-3839 (Canada), 6 am to 8 pm, Pacific Time, Monday through Friday,
and 7 am to 4 pm, Pacific Time, Saturday.
This device complies with RSS-210 of the Industry Canada Rules. Operation
is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Days and hours of support are subject to change without notice. Toll or long
distance charges may apply.
Radiation Exposure Statement:
Internet support
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
Visit www.epson.com/support (U.S.) or www.epson.ca/support
(Canada) for solutions to common problems. You can download utilities and
documentation, get FAQs and troubleshooting advice, or e-mail Epson.
Declaration of Conformity
Registration
Register today to get product updates, special promotions, and customer-only
offers. You can use the CD included with your projector or register online at
www.epson.com/webreg.
Optional accessories
For a list of optional accessories, see the online User’s Guide.
You can purchase RF 3D glasses or other accessories from an EPSON authorized
reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you
can purchase online at www.epsonstore.com (U.S. sales) or www.epson.ca
(Canadian sales).
Notices
Bluetooth Safety and Specifications
Contains Bluetooth module model: DBUB-E207
This document provides safety instructions and describes the specifications.
Read this document carefully before use to ensure your safety and product
performance.
U.S.
Contains FCC ID: BKMAE-E207
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
Reorient or relocate the receiving antenna.
•�������������������������������������������
Increase the separation between the equipment and receiver.
•�����������������������������������������������������������
Connect the equipment into an outlet on a circuit different from that to
•�������������������������������������������������������������������������
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
•������������������������������������������������������������������
According to 47CFR, Part 2 and 15, Class B Personal Computers and Peripherals;
and/or CPU Boards and Power Supplies used with Class B Personal Computers
We:
Located at: Tel:
Epson America, Inc.
3840 Kilroy Airport Way
MS: 3-13
Long Beach, CA 90806
562-290-5254
Declare under sole responsibility that the product identified herein, complies
with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device. Each
product marketed, is identical to the representative unit tested and found
to be compliant with the standards. Records maintained continue to reflect
the equipment being produced can be expected to be within the variation
accepted, due to quantity production and testing on a statistical basis as
required by 47CFR 2.909. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Trade Name: EPSON
Type of Product: LCD Projector
Model:
H501A
Marketing Name:PowerLite Home Cinema 3020
Epson America, Inc. Limited Warranty
Two-Year Projector Limited Warranty, 90-Day Lamp Limited Warranty and
1-Year 3D Glasses Limited Warranty
the cost of a replacement projector in the event that you fail to return the
defective one. When Epson authorizes an exchange for defective 3D glasses,
you must first send in the defective glasses to Epson. Once we have received
your defective glasses Epson will ship a replacement product to you, freight
prepaid, so long as you use an address in the United States, Canada, or Puerto
Rico. If Epson authorizes repair instead of exchange, Epson will direct you to
send your product to Epson or its authorized service center, where the product
will be repaired and sent back to you. You are responsible for packing the
product and for all costs to and from the EPSON authorized service center.
When warranty service involves the exchange of the product or of a part,
the item replaced becomes Epson property. The exchanged product or part
may be new or refurbished to the Epson standard of quality, and at Epson’s
option, the replacement may be another model of like kind and quality. Epson’s
liability for replacement of the covered product will not exceed the original
retail selling price of the covered product. Exchange or replacement products
or parts assume the remaining warranty period of the product covered by this
limited warranty. If Epson replaces the lamp as part of the warranty service, the
replacement lamp carries the limited 90-day warranty stated above.
What This Warranty Does Not Cover: This warranty covers only normal use in
the United States, Canada or Puerto Rico. Twenty-four hours per day or other
excessive continual use is not considered normal use. This warranty does not
cover consumables such as filters. This warranty is not transferable. Epson is not
responsible for warranty service should the EPSON label or logo or the rating
label or serial number be removed. Epson is not responsible for warranty service
should the product fail to be properly maintained or fail to function properly
as a result of misuse, abuse, improper installation, neglect, improper shipping,
damage caused by disasters such as fire, flood, and lightning, improper
electrical current, software problems, interaction with non-EPSON products,
or service other than by Epson or an EPSON Authorized Servicer. Postage,
insurance, or shipping costs incurred in presenting your EPSON product for
carry-in warranty service are your responsibility. Epson will pay for all freight
charges if you choose to send your unit to Epson for repair. If a claimed defect
cannot be identified or reproduced in service, you will be held responsible for
costs incurred.
THE WARRANTY AND REMEDY PROVIDED ABOVE ARE EXCLUSIVE AND IN
LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE. SOME LAWS DO NOT ALLOW THE EXCLUSION OF
IMPLIED WARRANTIES. IF THESE LAWS APPLY, THEN ALL EXPRESS AND IMPLIED
WARRANTIES ARE LIMITED TO THE WARRANTY PERIOD IDENTIFIED ABOVE.
UNLESS STATED HEREIN, ANY STATEMENTS OR REPRESENTATIONS MADE BY
ANY OTHER PERSON OR FIRM ARE VOID. IN THE EVENT THE REMEDIES ABOVE
FAIL, EPSON’S ENTIRE LIABILITY SHALL BE LIMITED TO A REFUND OF THE
PRICE PAID FOR THE EPSON PRODUCT COVERED BY THIS LIMITED WARRANTY.
EXCEPT AS PROVIDED IN THIS WRITTEN WARRANTY, NEITHER EPSON AMERICA,
INC. NOR ITS AFFILIATES SHALL BE LIABLE FOR ANY LOSS, INCONVENIENCE,
OR DAMAGE, INCLUDING DIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES, RESULTING FROM THE USE OR INABILITY TO USE THE EPSON
PRODUCT, WHETHER RESULTING FROM BREACH OF WARRANTY OR ANY OTHER
LEGAL THEORY.
In Canada, warranties include both warranties and conditions.
What Is Covered: Epson America, Inc. (“Epson”) warrants to the original retail
purchaser of the EPSON projector product enclosed with this limited warranty
statement that the product, if purchased new and operated in the United
States, Canada, or Puerto Rico will be free from defects in workmanship and
materials for a period of two (2) years from the date of original purchase. This
limited warranty applies only to the projector and not to the projector lamp or
3D glasses. The projector lamp carries a limited warranty period of ninety (90)
days from the date of original purchase. The 3D glasses carry a limited warranty
period of one (1) year from the date of original purchase. For warranty service,
you must provide proof of the date of original purchase.
What Epson Will Do To Correct Problems: If your product requires service
during the limited warranty period, please call Epson at the number on the
bottom of this statement and be prepared to provide the model, serial number,
and date of original purchase. Epson will, at its option, repair or replace
the defective unit, without charge for parts or labor. If Epson authorizes an
exchange for the defective projector, Epson will ship a replacement projector
to you, freight prepaid, so long as you use an address in the United States,
Canada, or Puerto Rico. You are responsible for securely packaging the
defective unit and returning it to Epson within five (5) working days of receipt
of the replacement. Epson requires a debit or a credit card number to secure
Some jurisdictions do not allow limitations on how long an implied warranty
lasts and some jurisdictions do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitations and exclusions
may not apply to you. This warranty gives you specific legal rights, and you may
also have other rights, which vary from jurisdiction to jurisdiction.
To find the EPSON Authorized Reseller nearest you, please visit our website at:
www.epson.com.
To find the EPSON Customer Care Center nearest you, please visit
www.epson.com/support.
To contact the EPSON ConnectionSM, please call (800) 637-7661 or (562) 276-4394
in the U.S. and (905) 709-3839 in Canada or write to Epson America, Inc., P.O.
Box 93012, Long Beach, CA 90809-3012.
EPSON and PowerLite are registered trademarks, and EPSON Exceed Your Vision is a registered logomark of
Seiko Epson Corporation. PrivateLine is a registered trademark and EPSON Connection is a service mark of
Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks
of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2012 Epson America, Inc. 7/12
Printed in XXXXXX
CPD-37709
Download PDF