American DJ Accu UFO PRO Specifications

American DJ
®
Accu UFO PRO
Table of Contents
User Instructions
Rev. 2/11
Unpacking......................................................................3
Introduction....................................................................3
Customer Support......................................................................3
Safety Precautions......................................................................4
General Information.....................................................................5
Features.........................................................................5
Registration......................................................................5
Mounting..............................................................................6
Controls & Features.....................................................................8
DMX Set-Up..............................................................................11
System Menu............................................................................14
Editing Program.........................................................................29
Error Codes...............................................................................34
Operation...........................................................................36
DMX Traits.................................................................................38
Fuse Replacement....................................................................42
Cleaning..................................................................42
Trouble Shooting.......................................................................42
Warranty.................................................................43
Specifications....................................................................44
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 2
Accu UFO PRO Introduction
Unpacking: Thank you for purchasing the Accu UFO PRO by American DJ®. Every Accu UFO PRO has been thoroughly tested and has
been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your fixture for any
damage and be sure all equipment necessary to operate the unit has
arrived intact. In the event damage has been found or parts are missing, please contact our toll free customer support number for further
instructions. Please do not return this unit to your dealer without contacting customer support first.
Introduction: The Accu UFO PRO is a unique, ten channel, rotating moving head, DMX intelligent LED fixture. The fixture can operate
in three different operating modes; stand alone, sound-active, or in a
Master/Slave configuration. The Accu UFO PRO comes with several
built in programs that can be used, while operating as a stand alone
unit or when used in multiples linked in a master/slave configuration.
For best results use fog or special effects smoke to enhance the beams
projections.
Customer Support: American DJ® provides a toll free customer
support line, to provide help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.americandj.com for any comments or
suggestions. Service Hours are Monday through Friday 9:00 a.m. to
4:30 p.m. Pacific Standard Time.
Voice:
(800) 322-6337
Fax: (323) 582-2941
E-mail: support@americandj.com
To purchase parts online visit http://parts.americandj.com
Warning! To prevent or reduce the risk of electrical shock or fire, do
not expose this unit to rain or moisture.
Warning! This may cause severe eye damage. Avoid looking directly
into the light source at all times!
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 3
Accu UFO PRO Safety Precautions
For Your Own Personal Safety, Please Read and Understand This
Manual Completely Before You Attempt To Install Or Operate
This Unit!
•To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture
•Do not spill water or other liquids into or on to your unit.
•Be sure that the local power outlet match that of the required voltage for your unit.
•Do not attempt to operate this unit if the power cord has been
frayed or broken.
•Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short.
•Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
•Never operate this unit when it’s cover is removed.
•Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall.
•Do not attempt to operate this unit, if it becomes damaged.
•This unit is intended for indoor use only, use of this product outdoors voids all warranties.
•Always mount this unit in safe and stable matter.
•Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience recep-
tacles, and the point where they exit from the appliance.
• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 38 for cleaning details.
•Heat -This fixture should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
•The fixture should be serviced by qualified service personnel when:
A. Objects have fallen, or liquid has been spilled into the appliance.
B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally or exhibits a marked change in performance.
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 4
Accu UFO PRO
General Information
To optimize the performance of this product, please read these operating
instructions carefully to familiarize yourself with the basic operations of
this unit. These instructions contain important safety information regard
ing the use and maintenance of this unit. Please keep this manual with
the unit, for future reference.
Accu UFO PRO
-
attempt any repairs yourself, doing so will void your manufactures war
ranty. In the unlikely event your unit may require service please contact
American DJ ® .
Accu UFO PRO
•
•
•
•
•
•
•
•
•
When installing the unit, the trussing or area of installation must be
able to hold 10 times the weight without any deformation. When
installing the unit must be secured with a secondary safety attach
ment, e.g. and appropriate safety cable. Never stand directly below
the unit when mounting, removing, or servicing the unit.
-
Overhead mounting requires extensive experience, including calculat
ing working load limits, installation material being used, and perodic
safety inspection of all installation material and unit. If you lack these
qualifications, do not attempt the installation yourself.
American DJ ® will not accept any liability for any resulting damages
caused by the non-observance of this manual or any unauthorized
modification to this unit.
Caution! There are no user serviceable parts inside this unit. Do not
Mounting
-
These installaiton should be checked by a skilled person once
a year.
Features
3 Operating Modes -Sound Active, Auto, and DMX Control
2 DMX Channel Modes: 8 & 10 Channel Modes
Internal Microphone
Bright 1 Watt LEDs
Edit and Save Scenes into the Memory
Variable Strobe (1-24 fps)
Switchable 540˚ to 360 Pan Movement
265˚ Tilt Movement
Digital Display for Address and Function Setting
Accu UFO PRO
Product Registration
The Accu UFO PRO carries a three year (1095 day) limited warranty.
Please fill out the enclosed warranty card to validate your purchase.
All returned service items whether under warranty or not, must be
freight pre-paid and accompany a return authorization (R.A.) number.
The R.A. number must be clearly written on the outside of the return
package. A brief description of the problem as well as the R.A. num
ber must also be written down on a piece of paper
and included in the
shipping carton. If the unit is under warranty, you must provide a copy
of your proof of purchase invoice. You may obtain a R.A. number by
contacting our customer support team on our toll free customer sup
port number. All packages returned to the service department not dis
playing a R.A. number on the outside of the package will be returned
to the shipper at the shippers cost.
American DJ
®
- www.americandj.com - Accu UFO PRO Instruction Manual Page 5
The Accu UFO PRO is fully operational in three different mounting
positions, hanging upside-down from a ceiling, side mounted, or set
on a flat level surface. To avoid internal damage to the unit, never
mount the unit on its side as illustrated above. Be sure this fixture is
kept at least 0.5m away from any flammable materials (decoration
etc.). Always use and install the supplied safety cable as a
safety
measure to prevent accidental damage and/or injury in the event the
clamp fails (see next page). Never use the carrying handles for sec
ondary attachment.
American DJ
®
- www.americandj.com - Accu UFO PRO Instruction Manual Page 6
-
Accu UFO PRO Mounting
NOTICE: The suitable enviromental temperature for this lighting fixture is between -25˚ C to 45˚ C. Do not place this lighting
fixture in an enviroment where the temperatures are under or
above the temperatures stated above. This will allow the fixture
to run at its best and help prolong the fixture life.
Accu UFO PRO Controls & Features
Screw one clamp each via a M12 screw and nut onto the
Omega holders. Insert the quick-lock fasteners of the first
Omega holder into the respective holes on the bottom of the
Accu UFO PRO. Tighten the quick-lock fasteners fully clockwise. Install the second Omega holder. Pull the safety-cable
through the holes on the bottom of the base and over the trussing system or a safe fixation spot. Insert the end in the carabine
and tighten the safety screw.
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 7
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 8
Accu UFO PRO Controls & Features
1.Lens Assembly - There are 12 high quality lenses that make up the
circular shaped moving head.
2. Digital Display - This display shows the menu and operating functions that you can choose from.
3. Mode/ESC Button - This button is used to exit menus and to scroll
backwards through certain menus only.
4. Up Button - This button is used to scroll forward when navigating
through the system menu.
5. Down Button - This button is used to scroll backwards when navigating through the system menu.
Accu UFO PRO Controls & Features
included with the unit, this cord is designed to match the electrical
requirements of the unit. Other cords may cause the unit to overheat
or malfunction. Never use this fixture if the ground prong has been
removed or broken off. The ground prong is designed to reduce the
risk of fire or electrical shock in the event the unit suffers from an internal short.
The fuse housing stores a 4 amp protective fuse. Never defeat the
fuse, the fuse is designed to protect the electronics in the event of
severe power fluctuations. Always be sure to replace the fuse with an
exact match as the one being replaced, unless otherwise told to do so
by an authorized American DJ® service technician.
6. Enter Button - This button is used to select and confirm a function when working in the system menu. It is also used to exit certain
menus.
7. Microphone - This microphone receives external low frequencies
to trigger the unit in Sound-Active mode. This microphone is designed
to receive low frequency sounds only, tapping on the microphone and
high pitch sounds may not trigger the unit.
8. Carrying Handles - The includes built-in carrying handles. Be sure
to always handle the unit by the built-in handles. Never lift or carrying the unit by head or yoke. Pulling on or transporting the unit by the
moving head may severely damage the unit and will void the unit warranty.
9. XLR Output Jack - This jack is used to transmit the incoming
DMX s ignal to another DMX fixture, or transmit a Master/Slave signal
to the next Accu UFO PRO in the chain. For best results in DMX or
Master/Slave mode terminate this jack if it is the last unit in the chain.
See “Terminator” on page 12.
10. XLR DMX Input Jack - This jack is used to receive an incoming
DMX s ignal or Master/Slave signal.
11. Power Switch - This switches the power to the fixture “On” and
“Off”.
12. Power Cord Inlet & Fush Holder - This unit is equipped with
a removable I.E.C. power cord. Be sure to only use the power cord
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 9
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 10
REMOTE
CONTROL
INPUT
SOUND
Accu UFO PRO
DMX Set Up
OUTPUT
2
3
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 11
DMX Set Up
POWER
COMMON
DMX512 OUT
3-PIN XLR
1
2
DMX +
3
DMX -
3
1
DMX512 IN
3-PIN XLR
2
3
1
2
Figure 2
XLR Female Socket
XLR Male Socket
1 Ground
2 Cold
2 Cold
REMOTE
CONTROL
INPUT
SOUND
INPUT
OUTPUT
1 Ground
XLR Pin Configuration
Pin 1 = Ground
REMOTE
CONTROL
SOUND
3 Hot
INPUT
OUTPUT
INPUT
Pin 2
= Data Compliment (negative)
3 Hot
Pin 3 = Data True (positive)
Figure 3
Special Note: Line Termination. When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
POWER
DMX512
DMX+,DMX-,COMMON
1
SOUN
DMX+,DMX-,COMMON
cables. Do not use
the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
POWER
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The Accu UFO PRO can be controlled via DMX-512 protocol. The Accu UFO PRO can be either a 8 or 10 channel DMX unit.
The DMX address is set electronically using the controls on the front
panel of the unit. Your unit and your DMX controller
COMMON
require an approved DMX-512 110 Ohm Data cable
DMX +
DMX512 OUT
3-PIN XLR
for data input and data output (Figure 1). We recomDMX mend Accu-Cable DMX cables. If you are making
your own cables, be sure to use standard 110-120
Ohm shielded cable (This cable may be purchased
at almost all pro lighting stores). Your cables should
be made with a male and female XLR connector on
Figure 1
either end of the cable. Also remember that DMX cable must be daisy
OUTPUT
Notice: Be sure to follow
figures two and three when making your own
DMX512
tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
INPUT
INPUT
POWER
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
REMOTE
CONTROL
INPUT
REMOTE
CONTROL
INPUT
SOUND
chained and cannot be split.
tronic ballast, which will auto sense the voltage when it is plugged into
the power source. With the electronic ballast you do not need to worry
about wall voltage, this unit can be plugged in anywhere.
SOUND
OUTPUT
Accu UFO PRO
Power Supply: The American DJ® Accu UFO PRO contains a elec-
DMX Linking: DMX is a language allowing all makes and models
of different manufactures to be linked together and operate from a
single controller, as long as all fixtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using
several DMX fixtures try to use the shortest cable path possible. The
order in which fixtures are connected in a DMX line does not influence
the DMX addressing. For example; a fixture assigned a DMX address
of 1 may be placed anywhere in a DMX line, at the beginning, at the
end, or anywhere in the middle. Therefore, the first fixture controlled
by the controller could be the last fixture in the chain. When a fixture
is assigned a DMX address of 1, the DMX controller knows to send
DATA assigned to address 1 to that unit, no matter where it is located
in the DMX chain.
INPUT
3
1
2
DMX512 IN
3-PIN XLR
3
1
2
POWER
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Figure 4
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 12
Termination
avoids sign
and interfere
to connect a
120 Ohm 1/4
and PIN 3 (
Accu UFO PRO
DMX Set Up
Accu UFO PRO
System Menu
5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
fixtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
1
ADDR
AXXX A001
2
TEST
T-01~T-XX
RUN
MSTR/ALON
Indicate the staring DMX address
A001 also is the setting for slave
Automatically test the function
Runs fixture as “master” or “alone” for auto
3
PLAY
AUDI
MSTR/ALON
Runs fixture as “master” or “alone” for audio
AUTO
Clos/ Hold/Auto/Audi
Runs fixture for no DMX
4
RESE
Conductor
3-Pin XLR Female (Out)
5-Pin XLR Male (In)
5
TIME
Ground/Shield
Pin 1
Pin 1
Data Compliment (- signal)
Pin 2
Pin 2
Data True (+ signal)
Pin 3
Pin 3
6
7
8
9
10
RPAN
RTLT
FINE
DEGR
MIC
Not Used
Pin 4 - Do Not Use
11
DISP
Not Used
Pin 5 - Do Not Use
12
SPEC
ALL
SCAN
LIFE
CLMT
ON/OFF
ON/OFF
ON/OFF
360/540
M-XX
VALU
D ON
FLIP
LOCK
RDMX
SPEE
DFSE
FEED
HIBE
VER
ADJU
STEP
13
EDIT
SCXX
REC.
RUN
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 13
Reset all motors and returns fixture to home
Reset only motors for pan/tilt
Displays the total fixture running time
Clear fixture running time
Reverses the pan movements
Reverses the tilt movements
Switch between 16 bit/8 bit
Pan degree select
Mic sensitivity
D–XX D-00 (DXXX)
Display the DMX512 value of each channel
ON/OFF
Display turn off after 2mins
ON/OFF
This function will reverse the display 180
ON/OFF
Key Lock
ON/OFF
Change DMX address via external controller
SP-1/SP-2
Movement Mode Select
ON/OFF
Resets all the fixture functions to default
ON/OFF
Pan/tilt feedback (error correction) on/off
OFF/1-99M 15M
Stand by mode
V1.0~V9.9
Software version
CODE
CXXX
Fixture code *code is “C050”
CH01~CH30
XXXX(-128~127)
Motor Calibration
S–01 ~S–48
Set the amount of your program
C–01~C–30
XXX(000~255)
Edit the channels of each scene
TIME
T XXX(001~999)
Time for each scene
CEDT
ON/OFF
Edit program via controller
RE.XX
Auto Save
ON/OFF
Program test
0000~9999
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 14
Accu UFO PRO
System Menu
ADDRESS MENU A.OO1 - A.511 (Value) - This is where you set the DMX address of the
unit.
TEST MENU T-01 - T-XX (Test) - Tests the functions of each channel. Note: Some
channels cannot be tested.
PLAY MENU RUN - Runs the unit as a “master” or in a stand alone mode. The unit
will run a internal program mode.
AUDI (Audio) - Runs the unit as a “master” or in a stand alone, sound
active mode.
AUTO - This is a precaution mode in case the DMX signal is lost. There
are four settings to choose from:
• “Hold” - This is the default setting, which in case the signal is
lost the fixute will “hold” at the last setting.
Accu UFO PRO
System Menu
DEGR MENU 360/540 - Switch the degree of the Pan between 360 and 540.
MIC MENU M-01-M-70 - With this function you can make the internal mic more or
less sensitive to sound.
DISPLAY MENU VALU (DMX-512 Value) - Display the DMX-512 value of each channel.
D ON - Display will turn off in 2 minutes.
FLIP - “Flips” the digital display 180º.
LOCK - When activated the buttons will lock automatically. See page
23 for more information.
SPEC MENU RDMX - Lets you adjust the DMX address via external controller.
SPEE - Lets you select the movement mode.
• “Close” - The fixture will return to its “home” standing.
DFSE (Default Settings) - Resets the unit to the default settings.
• “Auto” - The fixture will go into Auto mode and run a pre-programmed show.
FEED - Pan/Tilt feedback (error correction) on/off.
• “Audi” - The fixture will go into Sound Active mode.
RESE (RESET) MENU ALL - Resets all the motors in the unit.
SCAN - Resets the motors that control pan/tilt.
HIBE - This feature will automatically shut down the lamp and
stepping motors. Please see pages 26.
VER (Version) - Displays the software version
ADJU - Calibration functions
CLMT - Clears the fixture running time.
EDIT MENU STEP (S-01 - S-48) - These are the steps slots that you write your
programs into. There are at total of 48 steps. See edit procedure on
page 31.
RPAN (REVERSE PAN) MENU ON/OFF - When “On” is chosen it will reverse the pan.
SCXX (SC01 - SC30) - These are the scenes that are stored in your program. There are a total of 30 scenes.
RTILT (REVERSE TILT) MENU ON/OFF - When “On” is chosen it will reverse the tilt.
REC - This will auto save your custom program.
TIME MENU LIFE - Displays the fixtures total running time.
RUN - This will run your custom program.
FINE MENU ON/OFF - Switch between 8bit and 16bit movement.
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 15
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 16
Accu UFO PRO
System Menu
On-Board System Menu. The Accu UFO PRO ccomes with an easy
to navigate system menu. This next section will detail the functions of
each command in the system menu.
To access the main menu press the MODE/ESC button on the front
of the unit. Tap the UP or DOWN butons until you reach function you
wish to change. When you reach the function you wish to change tap
the enter button. Again, tap the UP or down buttons to change the
function. Once your changes are made, tap the enter button to lock
the change in the system, if the enter button is not selected within
eight seconds the system will automatically return to menu section. To
exit without making any changes tap the MODE/ESC button.
ADDR MAIN MENU -
ADDR
DMX Address Setting via control board -
Accu UFO PRO
System Menu
PLAY MAIN MENU -
RUN Run the unit in an Auto mode as a “master” in a
Master/Slave configuration, or as a stand alone unit 1. Access the main menu.
2. Tap the UP button until “PLAY” is displayed, press ENTER.
3. Tap the UP button until “RUN” is displayed, press ENTER.
4. Tap the UP or DOWN button to choose between “MSTR” or
“ALON“, select your choice by pressing ENTER, “PASS” will flash
in the display and fixture will begin its function.
AUDI
1. Access the main menu.
Run the unit in Sound Active mode as a “master”, or
as a stand alone unit -
2. Tap the UP button until “ADDR” is displayed, press ENTER.
1. Access the main menu.
4. Now the display will show “A001”. Adjust the DMX address
by pressing the UP or DOWN buttons.
2. Tap the UP button until “PLAY” is displayed, press ENTER.
5. Press ENTER to confirm.
4. Tap the UP or DOWN button to choose between “MSTR” or
“ALON“, select your choice by pressing ENTER, “PASS” will flash
in the display and fixture will begin its function.
6. Press the MODE/ESC button to return to the main menu.
When the display is on “A001”, you can directly press the UP
or DN buttons to change the DMX start address.
TEST MAIN MENU -
TEST - This will test the functions of each channel. Note:
Some channels cannot be tested
3. Tap the UP button until “AUDI” is displayed, press ENTER.
AUTO
This is a precaution mode in case you lose the DMX
signal. The fixtue has 4 modes to choose from, please see
page 15 for a description of the 4 modes 1. Access the main menu by pressing MODE/ESC button.
1. Access the main menu.
2. Tap the UP button until “PLAY” is displayed, press ENTER.
2. Tap the UP button until “TEST” is displayed, press ENTER.
3. Tap the UP button until “AUTO” is displayed, press ENTER.
3. The display will show “T-01”. You can now press the up
button and test the different channels.
4. Now you can choose between “CLOSE”, “HOLD” “AUTO”, or
“AUDI”. “HOLD” is the default setting.
4. Press MODE/ESC to exit.
5. Select the mode that you want the fixture to run in case of a
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 17
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 18
Accu UFO PRO
System Menu
lost DMX signal and press ENTER.
RESE MAIN MENU -
ALL - When you activate the reset function, the fixture will
begin the reset motion.
Accu UFO PRO
CLMT - With this function you can clear the running time of
the fixture.
1. Access the main menu.
2. Tap the UP button until “TIME” is displayed, press ENTER.
3. Tap the UP button until “CLMT” is displayed, press ENTER.
1. Access the main menu.
4. Press ENTER to confirm.
2. Tap the UP button until “RESE” is displayed, press ENTER.
5. Press MODE/ESC to return to the main menu.
3. Tap the UP button until “ALL” is displayed.
4. Press ENTER to reset all motors, or press MODE/ESC to
cancel and return to the main menu.
SCAN - When you activate this reset function, the fixture
will only reset the pan/tilt motor.
1. Access the main menu.
2. Tap the UP button until “RESE” is displayed, press ENTER.
3. Tap the UP button until “SCAN” is displayed.
4. Press ENTER to reset the pan/tilt motors, or press MODE/
ESC to cancel and return to the main menu.
TIME MAIN MENU -
System Menu
RPAN MENU -
RPAN - The movement of the Pan will be reversed.
1. Access the main menu.
2. Tap the UP button until “RPAN” is displayed, press ENTER.
3. Press the UP or DOWN buttons to select either “ON” to activate this function, or “OFF” to deactivate this function.
4. Press ENTER to confirm.
5. Press MODE/ESC to return to the main menu.
RTILT MENU -
RTILT - The movement of the Tilt will be reversed.
LIFE - With this function you can display the total running
1. Access the main menu.
time of the unit.
2. Tap the UP button until “RTILT” is displayed, press ENTER.
1. Access the main menu.
3. Press the UP or DOWN buttons to select either “ON” to activate this function, or “OFF” to deactivate this function.
2. Tap the UP button until “TIME” is displayed, press ENTER.
3. Tap the UP button until “LIFE” is displayed, press ENTER.
4. Press MODE/ESC to return to the main menu.
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 19
4. Press ENTER to confirm.
5. Press MODE/ESC to return to the main menu.
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 20
Accu UFO PRO
System Menu
FINE MENU -
FINE - Switch between 8bit (coarse) and 16bit (fine) pan &
tilt movement. This also switches the DMX Channel mode
between 8 channel (8 bit) and 10 channel (16 bit) DMX
mode.
Accu UFO PRO
System Menu
3. Tap the UP button until “MIC” is displayed, press ENTER.
4. The display will show “M-01”.
5. Press the UP or DOWN button to adjust the microphone sensitivity between “M-01 - M-99”.
1. Access the main menu.
6. Press ENTER to confirm when you have reached your
desired microphone sesitivity level.
3. Tap the UP button until “FINE” is displayed, press ENTER.
7. Press MODE/ESC to return to the main menu.
4. Press the UP or DOWN buttons to select either “ON” (10
Channel Mode) to activate this function, or “OFF” (8 Channel
Mode) to deactivate this function.
DISP MAIN MENU -
5. Press ENTER to confirm.
6. Press MODE/ESC to return to the main menu.
DEGR MENU -
DEGR - With this function you can switch the Pan degree
between 360° and 540°.
1. Access the main menu.
2. Tap the UP button until “DEGR” is displayed, press ENTER.
3. Press the UP or DOWN buttons to select either “360” or
“540”.
4. Press ENTER to confirm your selection.
VALU
Display the DMX-512 value of each channel -
1. Access the main menu.
2. Tap the UP button until “DISP” is displayed, press ENTER.
3. Tap the UP button until “VALU” is displayed, press ENTER.
4. The display should show “D-00”. Press the UP button in
order to select the desired channel. If you select “D-05” the
display will only show the DMX value of the 5th channel
5. Press ENTER to confirm.
6. Press MODE/ESC to return to the main menu.
Now the display will change as per the 5th channel DMX
value.
5. Press MODE/ESC to return to the main menu.
D ON
MIC MENU -
1. Access the main menu.
MIC - The internal microphone can be made more or less
sensitive.
1. Access the main menu.
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 21
With this function “On” the display will shut off after
2 minutes 2. Tap the UP button until “DISP” is displayed, press ENTER.
3. Tap the UP button until “D ON” is displayed, press ENTER.
4. Press the UP or DOWN buttons to select either “ON” to acti©American
DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 22
Accu UFO PRO
System Menu
vate this function, or “OFF” to deactivate this function.
5. Press ENTER to confirm.
6. Press MODE/ESC to return to the main menu.
FLIP - This function will reverse the display 180º.
1. Access the main menu.
2. Tap the UP button until “DISP” is displayed.
Accu UFO PRO
System Menu
SPEC MAIN MENU -
RDMX
With this function you are able to change the DMX
address via any DMX controller. This function is factory set
to “ON” already.
1. Access the main menu by pressing MODE/ESC.
2. Tap the UP button until “SPEC” is displayed, press ENTER.
3. Tap the UP button until “RDNX” is displayed, press ENTER.
3. Tap the UP button until “FLIP” is displayed, press ENTER.
4. Press the UP button to select “ON” to activate this function,
or “OFF” to deactivate.
4. Press the UP or DOWN buttons to select either “ON” to activate this function, or “OFF” to deactivate this function.
5. Press ENTER to confirm, and “PASS” will flash quickly.
5. Press ENTER to confirm.
6. Press MODE/ESC to return to the main menu.
LOCK - With this function you can activate the automatic
button lock. When this function is activated, the buttons
will automatically lock 15 seconds after the last press of
a button. In order to deactivate the button lock, press the
MODE/ESC button for 3 seconds.
1. Access the main menu.
2. Tap the UP button until “DISP” is displayed.
3. Tap the UP button until “LOCK” is displayed, press ENTER.
4. Press the UP or DOWN buttons to select either “ON” to activate this function, or “OFF” to deactivate this function.
5. Press ENTER to confirm.
6. Press MODE/ESC to return to the main menu.
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 23
6. Press MODE/ESC to return to the main menu.
To use this function follow the instructions:
To adjust the address of your unit you must first go to the
address that it is currently set to. From there you can adjust the
address. First make sure all channels are set to the value of “0”.
1. On your DMX controller set the DMX value of Channel 1 to
the value “7”.
2. Now set the DMX value of Channel 2 to the value “7” to
adjust the starting address between 1 and 255. To adjust the
address between 256 and 511 set Channel 2 to the value “8” .
3. Set the DMX value of Channel 3 to your desired starting address. This will take about 20 seconds before the unit
accepts the new DMX address.
EXAMPLE: So, if you want the address to be 57, you must first
set the address that is currently assingned to the unit. The proceed to set Channel 1 value to “7”, Channel 2 value to “7”, and
Channel 3 value to “57”.
2nd Example: Again, if you want the address to be 420, you
must first set the address that is currently assingned to the unit.
If you want the set the address to 420, set Channel 1 value to
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 24
Accu UFO PRO
System Menu
“7”, Channel 2 value to “8”, and Channel 3 to “164”. (256 + 164
= 420)
SPEE - With this function you can select the movement
mode
1. Access the main menu.
2. Tap the UP button until “SPEC” is displayed, press ENTER.
Accu UFO PRO
FEED
System Menu
- With this function you can switch the Pan/Tilt error
correction on and off. This will automatically correct the
Pan/Tilt if it is somehow moved out of place.
1. Access the main menu.
2. Tap the UP button until “SPEC” is displayed, press ENTER.
3. Tap the UP button until “FEED” is displayed, press ENTER.
3. Tap the UP button until “SPEE” is displayed, press ENTER.
4. Press the UP or DOWN buttons to select either “ON” to activate this function, or “OFF” to deactivate this function.
4. Press the UP or DOWN buttons to select either “SP-1” or
“SP-2”.
5. Press ENTER to confirm.
5. Press ENTER to select your desired mode.
DFSE - With this function you can restore the factory
settings of the device. All settings will be set back to the
default values. Any edited scenes will be lost. When restoring the factory settings the unit must be set to the address
that the unit was in when you started editing.
1. Access the main menu.
2. Tap the UP button until “SPEC” is displayed, press ENTER.
3. Tap the UP button until “DFSE” is displayed, press ENTER.
4. The display will show “ON/OFF”.
6. Press MODE/ESC to return to the main menu.
HIBE - With this function you can make the unit auto-
matically shut down the lamp and stepping motors. The
default setting for this is 15 mins. After 15 mins if the unit
is not receiving a DMX signal, the unit will automatically
shut down the lamp and motors. This feature lengthens
the life of the lamp and motors. The shut down time can be
adjusted between OFF (no shut down) or 1 - 99 minutes.
Once the lamp and motors are shut down, it will reset itself
when it receives a DMX signal. When the function is set to
OFF, the lamp and motors will not shut down until power is
cut.
5. Press the UP button to display “ON” to activate this function,
or “OFF” to deactivate this function.
1. Access the main menu by pressing MODE/ESC button.
6. Press ENTER to confirm.
3. Press the UP or DOWN buttons to adjust the shut down time.
7. Press MODE/ESC to return to the main menu.
4. Press ENTER to confirm your selection.
When you exit this function, the unit will begin to reload
data.
5. Press MODE/ESC to return to the main menu.
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 25
2. Tap the UP button until “HIBE” is displayed, press ENTER.
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 26
Accu UFO PRO
System Menu
VER - Use this function to display the Software version of
the unit.
Accu UFO PRO
System Menu
to calibrate.
1. Access the main menu.
10. Once you reach your desired calibration press ENTER to
confirm and lock in your calibration.
2. Tap the UP button until “SPEC” is displayed, press ENTER.
3. Tap the UP button until “VER” is displayed, press ENTER.
11. Once you are completely finished press MODE/ESC to
return to the main menu.
4. The display will show “V-1.0”, the display may also show, “V2.0”, “V-9.9” etc.
5. Press MODE/ESC to exit.
ADJU - Use this function is used to make sure all motors
are aligned and to adjust any motors that are not.
1. Access the main menu.
2. Tap the UP button until “SPEC” is displayed, press ENTER.
3. Tap the UP button until “ADJU” is displayed, press ENTER.
4. Tap the UP button until “CODE” is displayed, press ENTER.
5. The display will show “CXXX”, were as “XXX” represents the
calibration password. The calibration password is “C050.” Use
the UP or DOWN buttons to enter the proper password.
6. Once the proper password is entered the display will read
“CHXX”, were as “XX” represents the fixture channel number.
7. Select the desired channel to be calibrated by pressing the
UP or DOWN buttons and then ENTER to confirm.
8. The display will then read “xxxx”, were “xxxx” stands for
the calibrate values.
9. Adjust the desired calibration value between –128 and 127
by pressing the UP and DOWN. As you scroll up and down
through the calibration values you will
notice slight changes in the wheel or motor you are attempting
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 27
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 28
Accu UFO PRO
Editing Program
EDIT - This menu item allows you to write a program into the
memory (EEPROM) via the control panel or via the external
controller. Please see pages 31-33 for detailed instructions.
Accu UFO PRO
Editing Program
2. Tap the UP button until “EDIT” is displayed, press ENTER.
3. Tap the UP button until “REC” is displayed.
STEP - With this function you can program the number of
4. The display shows “RE.XX”, “XX” stands for the scene
number in the internal memory of where your scenes from the
controller will be stored.
1. Access the main menu.
5. Press the UP or DOWN button to select your desired scene
number.
steps in your individual Program.
2. Tap the UP button until “EDIT” is displayed, press ENTER.
3. Tap the UP button until “STEP” is displayed, press ENTER.
4. The display shows “S-01”, this stands for the first step of
your program. You can call up to 48 scenes in “Run”. For example, if “S-05” is displayed, it means that “Run” will run the first
5 scenes you saved in “Edit”.
5. Press ENTER to save and press MODE/ESC to exit.
SC01 - With this function you can choose the number of
scenes in your Program.
6. Press ENTER to confirm, and the fixture will record the
scenes from the external controller.
7. Press MODE/ESC to return to the main menu.
RUN
With the function “RUN”, you can run your pre-made
program. You can set the number of steps under Step (S-01
- S-48). You can edit the individual scenes under Edit.
1. Access the main menu.
2. Tap the UP button until “EDIT” is displayed, press ENTER.
1. Access the main menu.
3. Tap the UP button until “RUN” is displayed, press ENTER.
2. Tap the UP button until “EDIT” is displayed, press ENTER.
4. “AUTO” is displayed. If you press the UP button it will show
“SOUN”. Select which one you want to activate, and press
ENTER.
3. Tap the UP button until “SC01” is displayed.
4. The display shows “SC01”, this stands for the first scene of
your program. You can call up to 48 scenes. For example, if
“SC05”, it means that “Run” will run the first 5 scenes you saved
in “Edit”.
5. Press ENTER to save and press MODE/ESC to exit.
5. Press UP, to select “ALON” or “NAST”. Which mean stand
alone, and master/slave mode.
6. Select a mode, and press ENTER to confirm.
7. Press MODE/ESC to return to the main menu.
REC - With this function you can record the scenes automatically for the external controller.
1. Access the main menu.
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 29
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 30
Accu UFO PRO
Editing Program
Accu UFO PRO
Editing Program
Editing procedure 1: Using the control board only.
1. Access the main menu.
2. Tap the UP button until “EDIT” is displayed. Press ENTER.
3. The display will show “SCXX”, the “X” again stands for the
scene number. For example, “SC01” is displayed, it means you
will be editing scene 1, press ENTER. You can change the
scene number by pressing the UP button.
4. Press ENTER, the display will show “C-X”, the “X” again
stands for the channel number. If “C-01” is displayed, you will
be editing channel 1 of your selected scene, press ENTER. You
can change the channel number by pressing the UP button.
5. The display will show the DMX value for the channel that is
being edited. It will be displayed as “11XX”, it stands for Channel
11 of the editing scene, the DMX value is “XX”.
6. Adjust the DMX value by pressing the UP button, until you
get the expected effect for this channel.
7. Press ENTER to enter the editing of the other channels of the
scene.
8. Repeat steps 5-8, until you finish setting all the DMX values
for all the channels of this scene, each scene can have 15
channels maximum.
9. Once all the channels are completed, the display will flash
“TIME”, this stands for the time needed to run this scene.
10. Press ENTER to edit the time needed, the display shows
“TXXX”, “X” stands for the time needed to run this scene. For
example, “T002” means scene 1 needs 0.4 seconds to run,
“T015” means scene 1 needs 3 seconds to run.
11. Adjust the time needed by pressing the UP button.
13. Repeat steps 3-12 to edit other scenes, you can edit and
save 48 scenes maximum.
14. Press MODE/ESC to exit, now you have edited and saved
scenes using the control board. The number of steps can be
defined under “Step” and the scenes can be called up under
“Run”. To run the scenes see page 28.
Editing procedure 2: Using an external controller (Manually
record scenes one by one):
1. Access the main menu.
2. Select “EDIT” by pressing the UP or DOWN buttons, press
ENTER.
3. The display shows “SC01”.
4. Press ENTER, and the display shows “C-01”.
5. Select “CEDT” by pressing the DOWN button, and press
ENTER.
6. The display “OFF”, press the UP button so that “ON” is displayed, and press ENTER.
7. The display will show “SCO2”. You have now successfully
downloaded the first scene.
8. Adjust the Step-time needed by pressing the UP button.
9. Call up the second scene in your controller now.
10. Repeat steps 7-9 until all desired scenes are downloaded.
11. Press MODE/ESC to exit. The number of steps can be
defined under “Step” and the scenes can be called up under
“Run”.
12. Press ENTER to save the settings for the scene you are
editing, the display will change to the next scene automatically.
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 31
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 32
Accu UFO PRO
Editing Program
Editing procedure 3: Record the selected scenes automatically from external controller:
1. Access the main menu.
2. Select “EDIT” by pressing the UP or DOWN buttons, press
ENTER.
3. Press the UP button until the display shows “STEP”, press
ENTER.
4. Now adjust and set the number of steps by pressing the
UP or DOWN buttons. Press ENTER to confirm the number of
steps, and “PASS” will display briefly.
5. Now press the DOWN button until “REC” is displayed, and
press ENTER.
6. The display will now show “RE.XX”, “XX” stands for the scene
number in the internal memory which the scenes from the controller will be stored to. Press ENTER when you have chosen
the scene number.
7. Call up the scenes on the controller, and the fixture will
record the scenes from the controller automatically. After the
number of scenes as selected in the “STEP” menu are loaded
into the fixture, it will stop the procedure and return to the previous menu.
8. Press MODE/ESC to exit the “EDIT” menu and return to the
main menu.
Accu UFO PRO
Error Codes
When power is applied, the unit will automatically enter a
“reset/test” mode. This mode brings all the internal motors to a
home position. If there is an internal problem with one or more
of the motors an error code will flash in the display in the form
of “XXer”, “XX” will represent a function number. For example,
when the display shows “03Er,” it means there is some type of
error with the channel 3 motor. If there are multiple errors during
the start-up process they will all flash in the display. For example: if the fixtures has errors on channel 1 and channel 3 all at
the same time, you will see the error message flash “01Er”, and
“03Er repeated 5 times.
If an error does occur during the initial start-up procedure the
fixture will self-generate a second reset signal and try to realign
all the motors and correct the errors, if the errors persist after a
second attempt a third attempt will be made.
If after a third attempt all the errors have not been corrected the
fixture will make the following determinations:
1) 3 or more errors - The fixture cannot function properly with
three or more errors therefore the fixture will place itself in a
stand-by mode until subsequent repairs can be made.
2) Less than 3 errors - If the fixture has less than 3 errors, therefore most other functions will work properly. The fixture will
attempt to operate normally until the errors can be corrected by
a technician. The errors in question will remain flashing in the
display as a reminder of internal errors.
01Er – PAN movement error:
This message will appear after a fixture reset, if the pan-yoke’s
magnetic-indexing circuit malfunctions (sensor failed or magnet
is missing) or there is a stepper motor failure (defective motor
or a defective motor IC drive on the main PCB).
03Er – TILT movement error:
This message will appear after a fixture reset, if the tilt magnetic-indexing circuit malfunctions (sensor failed or magnet is
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 33
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 34
Accu UFO PRO
Error Codes
missing) or there is a stepper motor failure (defective motor or a
defective motor IC drive on the main PCB).
06Er – COLOR WHEEL error:
This message will appear after a fixture reset, if the head’s magnetic-indexing circuit malfunctions (sensor failed or magnet is
missing) or there is a stepper motor failure (defective motor or a
defective motor IC drive on the main PCB).
Accu UFO PRO
Operation
Operating Modes: The Accu UFO PRO can operate in three
different modes. This next section will detail the differences in
the operating modes.
• Sound Active mode The unit will react to sound.
• Auto mode The unit will run through a built-in program.
• DMX control mode This function will allow you to control each individual fixtures traits
with a standard DMX-512 controller such as the Elation ® Show
Designer.™
Universal DMX Control: This function allows you to use a universal DMX-512 controller such as the Elation® DMX Operator™
or Elation® Show Designer™ to control head movement, the color
wheel, gobo wheel, and the shutter (strobe). A DMX controller allows
you to create unique programs tailored to your individual needs.
1. The Accu UFO PRO can be either a 8 or 10 DMX channels. See pages 38-41 for detailed description of the DMX traits.
2. To control your fixture in DMX mode, follow the set-up procedures
on pages 7-9 as well as the set-up specifications that are included with your DMX controller.
3. Use the controller’s faders to control the various DMX fixture traits.
4. This will allow you to create your own programs.
5. Follow the instructions on page 17 to set the DMX address.
6. For longer cable runs (more than a 100 feet) use a terminator on the last fixture.
7. For help operating in DMX mode consult the manual included with your DMX controller.
Stand-Alone (Sound Active or Auto Program): This mode allows
a single unit to run to the beat of the music or run through a built-in
program.
1. Access the main menu.
2. Tap the UP button until “PLAY” is displayed, and Press ENTER.
3. Tap the UP button until “AUTO” is displayed, and Press ENTER.
4. Press the UP or DOWN button to select “RUN”, or “AUDI”. “RUN” will make the unit run through a built-in program. “AUDI” will make the unit sound active.
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 35
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 36
Accu UFO PRO
5.
6.
7.
Operation
Select a mode, and press ENTER to confirm.
Press MODE/ESC if you want to return to the main menu.
You can invert the pan and tilt functions in the system menu by
following the directions on page 20.
Master-Slave Operation (Sound Active or Auto Program):
This function will allow you to link up to 16 units together and operate without a controller. The units can run a built-in program or run in
sound actiive mode. In Master-Slave operation one unit will act as the
controlling unit and the others will react to the controlling units programs. Any unit can act as a Master or as a Slave.
1. Using standard XLR microphone cables, daisy chain your units together via the XLR connector on the rear of the units. Remem-
ber the Male XLR connector is the input and the Female XLR connector is the output. The first unit in the chain (master) will use the female XLR connector only - The last unit in the chain will use the male XLR connector only. For longer cable runs we suggest a terminator at the last fixture.
2. Access the main menu.
3. Tap the UP button until “PLAY” is displayed, and Press ENTER.
4. Tap the UP button to choose between “RUN” or “AUDI”. “RUN” will make the units run through a built-in program. “AUDI” will make the units sound active.
5. Press UP, to select “ALON” or “NSTR”. Which means stand alone, or master mode.
6. Select “NAST” to designate the unit as the master and press ENTER to confirm. The Slave units do not need to be set, just
connect to the Master and they will beging to follow.
7. Press MODE/ESC if you want to return to the main menu
6. You can invert the pan and tilt functions in the system menu by
following the directions on page 20.
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 37
Accu UFO PRO Channel
1
2
3
8 DMX Channel Mode
Value
Function
0 - 255
PAN MOVEMENT 8bit
0 - 255
TILT MOVEMENT 8bit
SPEED OF PAN/TILT MOVEMENT
0 - 255
4
0-3
4 - 127
128 - 131
132 - 255
5
0 - 10
11 - 20
21 - 30
31 - 40
41 - 50
51 - 60
61 - 70
71 - 80
81 - 90
91 - 100
101 - 110
111 - 120
121 - 130
131 - 140
141 - 150
151 - 160
161 - 170
171 - 180
181 - 190
191 - 200
201 - 210
MAX - MIN
LENS INDEXING & ROTATION
LENS INDEXING
FOWARD LENS ROTATION
FAST - SLOW
NO ROTATION
BACKWARD LENS ROTATION
SLOW - FAST
LED EFFECTS
BLACKOUT
RED
GREEN
BLUE
WHITE
RED + GREEN
RED + BLUE
RED + WHITE
GREEN + BLUE
GREEN + WHITE
BLUE + WHITE
RED + GREEN + BLUE
RED + GREEN + WHITE
RED + BLUE + WHITE
GREEN + BLUE + WHITE
RED + GREEN + BLUE + WHITE
AUTO PROGRAM 1
AUTO PROGRAM 2
AUTO PROGRAM 3
AUTO PROGRAM 4
AUTO PROGRAM 5
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 38
Accu UFO PRO Channel
5
Value
211 - 220
221 - 230
231 - 240
241 - 255
6
0 - 255
7
0
1 - 95
96 - 127
128 - 159
160 - 191
192 - 223
224 - 255
8
0 - 19
20 - 79
80 - 84
85 - 87
88 - 99
100 - 119
120 - 139
140 - 159
160 - 179
180 - 199
200 - 219
220 - 239
240 - 255
8 DMX Channel Mode
Function
AUTO PROGRAM 6
AUTO PROGRAM 7
AUTO PROGRAM 8
AUTO PROGRAM 9
LED SPEED
SLOW - FAST
STROBING
NO FUNCTION
STROBING SLOW - FAST
NO FUNCTION
PULSE EFFECT IN SEQUENCES
NO FUNCTION
RANDOM STROBING SLOW - FAST
NO FUNCTION
RESET & INTERNAL PROGRAMS
NORMAL COLOR CHANGE
NO FUNCTION
ALL MOTOR RESET
SCANNER MOTOR RESET
NO FUNCTION
INTERNAL PROGRAM 1
INTERNAL PROGRAM 2
INTERNAL PROGRAM 3
INTERNAL PROGRAM 4
INTERNAL PROGRAM 5
INTERNAL PROGRAM 6
INTERNAL PROGRAM 7
SOUND ACTIVE
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 39
Accu UFO PRO Channel
1
2
3
4
5
10 DMX Channel Mode
Value
Function
0 - 255
PAN MOVEMENT 8bit
0 - 255
PAN FINE 16bit
0 - 255
TILT MOVEMENT 8bit
0 - 255
TILT FINE 16bit
SPEED OF PAN/TILT MOVEMENT
0 - 255
MAX - MIN
LENS INDEXING & ROTATION
0-3
4 - 127
LENS INDEXING
FOWARD LENS ROTATION
FAST - SLOW
NO ROTATION
BACKWARD LENS ROTATION
SLOW - FAST
6
128 - 131
132 - 255
7
LED EFFECTS
0 - 10
11 - 20
21 - 30
31 - 40
41 - 50
51 - 60
61 - 70
71 - 80
81 - 90
91 - 100
101 - 110
111 - 120
121 - 130
131 - 140
141 - 150
151 - 160
161 - 170
171 - 180
BLACKOUT
RED
GREEN
BLUE
WHITE
RED + GREEN
RED + BLUE
RED + WHITE
GREEN + BLUE
GREEN + WHITE
BLUE + WHITE
RED + GREEN + BLUE
RED + GREEN + WHITE
RED + BLUE + WHITE
GREEN + BLUE + WHITE
RED + GREEN + BLUE + WHITE
AUTO PROGRAM 1
AUTO PROGRAM 2
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 40
Accu UFO PRO Channel
7
Value
181 - 190
191 - 200
201 - 210
211 - 220
221 - 230
231 - 240
241 - 255
8
10 DMX Channel Mode
Function
AUTO PROGRAM 3
AUTO PROGRAM 4
AUTO PROGRAM 5
AUTO PROGRAM 6
AUTO PROGRAM 7
AUTO PROGRAM 8
AUTO PROGRAM 9
LED SPEED
0 - 255
9
SLOW - FAST
STROBING
0
1 - 95
96 - 127
128 - 159
160 - 191
192 - 223
224 - 255
10
NO FUNCTION
STROBING SLOW - FAST
NO FUNCTION
PULSE EFFECT IN SEQUENCES
NO FUNCTION
RANDOM STROBING SLOW - FAST
NO FUNCTION
RESET & INTERNAL PROGRAMS
0 - 19
20 - 79
80 - 84
85 - 87
88 - 99
100 - 119
120 - 139
140 - 159
160 - 179
180 - 199
200 - 219
220 - 239
240 - 255
NORMAL COLOR CHANGE
NO FUNCTION
ALL MOTOR RESET
SCANNER MOTOR RESET
NO FUNCTION
INTERNAL PROGRAM 1
INTERNAL PROGRAM 2
INTERNAL PROGRAM 3
INTERNAL PROGRAM 4
INTERNAL PROGRAM 5
INTERNAL PROGRAM 6
INTERNAL PROGRAM 7
SOUND ACTIVE
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 41
Accu UFO PRO
Fuse Replacement
The fuse holder located at the rear of the unit above the power cord. Disconnect from the main power supply. Insert a standard flat head screw driver in
to the fuse holder housing, located on the back of the unit. Turn the screwdriver in counter-clockwise direction to remove the fuse holder. Remove the
old fuse and discard it, replace the fuse with the same type. Insert the fuse
back into it’s housing.
Accu UFO PRO Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses and mirror should be carried out periodically to optimize light
output. Cleaning frequency depends on the environment in which the fixture
operates (I.e. smoke, fog residue, dust, dew). In heavy club use we recommend cleaning on a monthly basis. Periodic cleaning will ensure longevity,
and crisp output.
1. Use normal glass cleaner and a soft cloth to wipe down the outside cas-
ing.
2. Use a brush to wipe down the cooling vents and fan grill.
3. Clean the external optics and mirror with glass cleaner and a soft cloth every 20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every 30-60 days.
5. Always be sure to dry all parts completely before plugging the unit back in.
Accu UFO PRO Trouble Shooting
Listed below are a few common problems that you may encounter, with solutions.
No light output from the unit;
1.Be sure you have connected your unit into a standard 120v wall outlet.
2. Be sure the external fuse has not blown. The fuse is located at the rear of the unit.
3.Be sure the fuse holder is completely and properly seated.
Unit does not respond to sound;
1. Low frequencies (bass) should cause the unit to react to sound. Tap-
ping on the microphone, quiet or high pitched sounds may not activate the unit.
2.Check the Mic setting. It may be set to a lower sensitivity setting. See pages 21-22.
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 42
Accu UFO PRO Warranty
MANUFACTURER’S LIMITED WARRANTY
A. American DJ, Inc. hereby warrants, to the original purchaser, American DJ and American
Audio products to be free of manufacturing defects in material and workmanship for a prescribed
period from the date of purchase (see specific warranty period on reverse). This warranty shall be
valid only if the product is purchased within the United States of America, including possessions
and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought.
B.
For warranty service you must obtain a Return Authorization number (RA#) before
sending back the product. Contact American DJ, Inc. Service Department at 800-322-6337. Send
the product only to the American DJ, Inc. factory. All shipping charges must be pre-paid. If the
requested repairs or service (including parts replacement) are within the terms of this warranty,
American DJ, Inc. will pay return shipping charges only to a designated point within the United
States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories
should be shipped with the product. If any accessories are shipped with the product, American DJ,
Inc. shall have no liability whatsoever for loss of or damage to any such accessories, nor for the
safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is
modified in any manner which American DJ, Inc. concludes, after inspection, affects the reliability
of the product; if the product has been repaired or serviced by anyone other than the American DJ,
Inc. factory unless prior written authorization was issued to purchaser by American DJ, Inc.; if the
product is damaged because not properly maintained as set forth in the instruction manual.
D.
This is not a service contract, and this warranty does not include maintenance, cleaning
or periodic check-up. During the period specified above, American DJ, Inc. will replace defective parts at its expense with new or refurbished parts, and will absorb all expenses for warranty
service and repair labor by reason of defects in material or workmanship. The sole responsibility
of American DJ, Inc. under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of American DJ. All products covered by this
warranty were manufactured after January 1, 1990, and bear identifying marks to that effect.
E.
American DJ, Inc. reserves the right to make changes in design and/or improvements
upon its products without any obligation to include these changes in any products theretofore
manufactured. No warranty, whether expressed or implied, is given or made with respect to any
accessory supplied with products described above. Except to the extent prohibited by applicable
law, all implied warranties made by American DJ, Inc. in connection with this product, including
warranties of merchantability or fitness, are limited in duration to the warranty period set forth
above. And no warranties, whether expressed or implied, including warranties of merchantability
or fitness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s
sole remedy shall be such repair or replacement as is expressly provided above; and under no
circumstances shall American DJ, Inc. be liable for any loss or damage, direct or consequential,
arising out of the use of, or inability to use, this product. This warranty is the only written warranty applicable to American DJ and American Audio Products and supersedes all prior warranties and written descriptions of warranty terms and
conditions heretofore published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
• All American Audio Products = 1-year (365 day) Limited Warranty (except V-Plus Series Amplifiers)
• All American Audio V-Plus Series Amplifiers = 3-year (1095 day) Limited Warranty
• American DJ Lighting and American DJ Branded Products = 1-year (365 day) Limited Warranty
(Such as: Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble
Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding Laser Products, lamps,
and Star Tec Series)
• American DJ Laser Products and Star Tec Products = 90-Day Limited Warranty
• American DJ L.E.D. Products = 3-year (1095 day) Limited Warranty (excluding motors which
have a 1-year (365 day Limited Warranty)
American DJ® - www.americandj.com - Accu UFO PRO Instruction Manual Page 43
Accu UFO PRO Model: Voltage*:
LEDs:
Power Consumption:
Dimensions: Weight:
Fuse:
Duty Cycle:
DMX: Sound Active:
Working Position:
Warranty:
Specifications
Accu UFO PRO
100~240V, 50/60Hz
32 x 1W LED’s (8 Red, 8
Green, 8 Blue, & 8 White)
100W
16.5”(L) x 14”(W) x 18.5”(H)
425mm x 353mm x 467mm
30 Lbs. / 13.5 kgs.
4A
None
8 or 10 DMX Channels
Yes
Any Safe, Secure Position
3 Year (1095 days)
*Auto Sensing Voltage: This fixture contains a electronic
ballast, which will auto sense the voltage when it is plugged into
the power source.
Please Note: Specifications and improvements in the design
of this unit and this manual are subject to change without any
prior written notice.
©American DJ Supply
American DJ World Headquarters:
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-582-2610
Web: www.americandj.com / E-mail: info@americandj.com
American DJ Europe
Junostraat 2
6468 EW Kerkrade
Netherlands
service@americandj.eu / www.americandj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99