Extron electronics | MTP DA4 | User guide | Extron electronics MTP DA4 User guide

User Guide
Distribution Amplifiers
MTP DA4 and MTP DA8
Twisted Pair Distribution Amplifiers
68-975-01 Rev. E
06 12
Safety Instructions • English
Warning
This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment.
Power sources • This equipment should be operated only from the power source indicated on the product. This
equipment is intended to be used with a main power system with a grounded (neutral) conductor. The third
(grounding) pin is a safety feature, do not attempt to bypass or disable it.
This symbol is intended to alert the user of the presence of uninsulated
dangerous voltage within the product’s enclosure that may present a risk of
electric shock.
Power disconnection • To remove power from the equipment safely, remove all power cords from the rear of
the equipment, or the desktop power module (if detachable), or from the power source receptacle (wall plug).
Caution
Read Instructions • Read and understand all safety and operating instructions before using the equipment.
Retain Instructions • The safety instructions should be kept for future reference.
Follow Warnings • Follow all warnings and instructions marked on the equipment or in the user information.
Avoid Attachments • Do not use tools or attachments that are not recommended by the equipment
manufacturer because they may be hazardous.
Consignes de Sécurité • Français
Ce symbole sert à avertir l’utilisateur que la documentation fournie avec le
matériel contient des instructions importantes concernant l’exploitation et la
maintenance (réparation).
Ce symbole sert à avertir l’utilisateur de la présence dans le boîtier
de l’appareil de  tensions dangereuses non isolées posant des risques
d’électrocution.
Attention
Lire les instructions• Prendre connaissance de toutes les consignes de sécurité et d’exploitation avant
d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de sécurité afin de pouvoir les consulter à l’avenir.
Respecter les avertissements • Observer tous les avertissements et consignes marqués sur le matériel ou
présentés dans la documentation utilisateur.
Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni d’outils non recommandés par le
fabricant du matériel car cela risquerait de poser certains dangers.
Sicherheitsanleitungen • Deutsch
Power cord protection • Power cords should be routed so that they are not likely to be stepped on or pinched
by items placed upon or against them.
Servicing • Refer all servicing to qualified service personnel. There are no user-serviceable parts inside. To prevent
the risk of shock, do not attempt to service this equipment yourself because opening or removing covers may
expose you to dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are provided to prevent
overheating of sensitive components inside. These openings must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is incorrectly replaced. Replace it only with the
same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the
manufacturer’s instructions.
Avertissement
Alimentations • Ne faire fonctionner ce matériel qu’avec la source d’alimentation indiquée sur l’appareil. Ce
matériel doit être utilisé avec une alimentation principale comportant un fil de terre (neutre). Le troisième
contact (de mise à la terre) constitue un dispositif de sécurité : n’essayez pas de la contourner ni de la
désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger, déconnectez tous les
cordons d’alimentation de l’arrière de l’appareil ou du module d’alimentation de bureau (s’il est amovible) ou
encore de la prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de manière à ce que personne
ne risque de marcher dessus et à ce qu’ils ne soient pas écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de réparation-maintenance par un
technicien qualifié. Aucun des éléments internes ne peut être réparé par l’utilisateur. Afin d’éviter tout danger
d’électrocution, l’utilisateur ne doit pas essayer de procéder lui-même à ces opérations car l’ouverture ou le
retrait des couvercles risquent de l’exposer à de hautes tensions et autres dangers.
Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices, ceux-ci servent à empêcher les
composants internes sensibles de surchauffer. Ces ouvertures ne doivent jamais être bloquées par des objets.
Lithium Batterie • Il a danger d’explosion s’ll y a remplacment incorrect de la batterie. Remplacer uniquement
avec une batterie du meme type ou d’un ype equivalent recommande par le constructeur. Mettre au reut les
batteries usagees conformement aux instructions du fabricant.
Vorsicht
Dieses Symbol soll dem Benutzer in der im Lieferumfang enthaltenen
Dokumentation besonders wichtige Hinweise zur Bedienung und Wartung
(Instandhaltung) geben.
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene Stromquelle betrieben werden.
Dieses Gerät wurde für eine Verwendung mit einer Hauptstromleitung mit einem geerdeten (neutralen) Leiter
konzipiert. Der dritte Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese sollte nicht
umgangen oder außer Betrieb gesetzt werden.
Dieses Symbol soll den Benutzer darauf aufmerksam machen, daß im Inneren
des Gehäuses dieses Produktes gefährliche Spannungen, die nicht isoliert sind
und die einen elektrischen Schock verursachen können, herrschen.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten Sie alle Netzkabel aus der
Rückseite des Gerätes, aus der externen Stomversorgung (falls dies möglich ist) oder aus der Wandsteckdose
ziehen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden, sollten Sie alle Sicherheits-und
Bedienungsanleitungen genau durchlesen und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit des Produktes sollten Sie
aufbewahren, damit Sie im Bedarfsfall darauf zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und Anleitungen auf dem Gerät oder in der
Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte, die nicht ausdrücklich vom
Hersteller empfohlen wurden, da diese eine Gefahrenquelle darstellen können.
Instrucciones de seguridad • Español
Este símbolo se utiliza para advertir al usuario sobre instrucciones importantes de operación y mantenimiento (o cambio de partes) que se desean
destacar en el contenido de la documentación suministrada con los equipos.
Este símbolo se utiliza para advertir al usuario sobre la presencia de elementos con voltaje peligroso sin protección aislante, que puedan encontrarse
dentro de la caja o alojamiento del producto, y que puedan representar
riesgo de electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de operación y seguridad, antes de usar el
equipo.
Conservar las instrucciones • Conservar las instrucciones de seguridad para futura consulta.
Obedecer las advertencias • Todas las advertencias e instrucciones marcadas en el equipo o en la
documentación del usuario, deben ser obedecidas.
Evitar el uso de accesorios • No usar herramientas o accesorios que no sean especificamente
recomendados por el fabricante, ya que podrian implicar riesgos.
安全须知 • 中文
这个符号提示用户该设备用户手册中有重要的操作和维护说明。
这个符号警告用户该设备机壳内有暴露的危险电压,有触电危险。
注意
阅读说明书
保存说明书
遵守警告 •
避免追加 •
• 用户使用该设备前必须阅读并理解所有安全和使用说明。
• 用 户应保存安全说明书以备将来使用。
用户应遵守产品和用户指南上的所有安全和操作说明。
不要使用该产品厂商没有推荐的工具或追加设备,以避免危险。
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im Weg liegen und niemand
darauf treten kann oder Objekte darauf- oder unmittelbar dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem Servicepersonal durchgeführt werden.
Die internen Komponenten des Gerätes sind wartungsfrei. Zur Vermeidung eines elektrischen Schocks
versuchen Sie in keinem Fall, dieses Gerät selbst öffnen, da beim Entfernen der Abdeckungen die Gefahr eines
elektrischen Schlags und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist, dienen diese zur
Vermeidung einer Überhitzung der empfindlichen Teile im Inneren. Diese Öffnungen dürfen niemals von
anderen Objekten blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt wird. Ersetzen Sie verbrauchte Batterien
nur durch den gleichen oder einen vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird.
Entsorgen Sie verbrauchte Batterien bitte gemäß den Herstelleranweisungen.
Advertencia
Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo de alimentación eléctrica
indicada en el mismo. La alimentación eléctrica de este equipo debe provenir de un sistema de distribución
general con conductor neutro a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no
puentearia ni eliminaria.
Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida de alimentación
eléctrica al equipo, desenchufar todos los cables de alimentación en el panel trasero del equipo, o desenchufar
el módulo de alimentación (si fuera independiente), o desenchufar el cable del receptáculo de la pared.
Protección del cables de alimentación • Los cables de alimentación eléctrica se deben instalar en lugares
donde no sean pisados ni apretados por objetos que se puedan apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal calificado. En el interior no
hay partes a las que el usuario deba acceder. Para evitar riesgo de electrocución, no intentar personalmente la
reparación/mantenimiento de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes
peligrosos u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento, es para evitar el
sobrecalientamiento de componentes internos sensibles. Estas aberturas nunca se deben obstruir con otros
objetos.
Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición incorrecta. Cambiar esta
batería únicamente con el mismo tipo (o su equivalente) recomendado por el fabricante. Desachar las baterías
usadas siguiendo las instrucciones del fabricante.
警告
电源 • 该设备只能使用产品上标明的电源。 设备必须使用有地线的供电系统供电。 第三条线(
地线)是安全设施,不能不用或跳过 。
拔掉电源 • 为安全地从设备拔掉电源,请拔掉所有设备后或桌面电源的电源线,或任何接到市电
系统的电源线。
电源线保护 • 妥善布线, 避免被踩踏,或重物挤压。
维护 • 所有维修必须由认证的维修人员进行。 设备内部没有用户可以更换的零件。为避免出现触
电危险不要自己试图打开设备盖子维修该设备。
通风孔 • 有些设备机壳上有通风槽或孔,它们是用来防止机内敏感元件过热。 不要用任何东西
挡住通风孔。
锂电池 • 不正确的更换电池会有爆炸的危险。必须使用与厂家推荐的相同或相近型号的电池。按
照生产厂的建议处理废弃电池。
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC rules. The Class A limits provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause interference; the user must correct the interference at his own expense.
NOTE: This unit was tested with shielded I/O cables on the peripheral devices. Shielded
cables must be used to ensure compliance with FCC emissions limits.
For more information on safety guidelines, regulatory compliances,
EMI/EMF compatibility, accessibility, and related topics, see the “Extron Safety
and Regulatory Compliance Guide” on the Extron website.
Conventions Used in this Guide
Notifications the following are used:
CAUTION: A caution indicates a situation that may result in minor injury.
ATTENTION: Attention indicates a situation that may damage or destroy the product or
associated equipment.
NOTE: A note draws attention to important information.
Copyright
© 2012 Extron Electronics. All rights reserved.
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
Contents
Introduction............................................................ 1
About the MTP DA4 and MTP DA8...................... 1
TP Cable Advantages........................................... 2
Transmission Distance...................................... 2
Termination and Mute Jumpering —
MTP 15HD Systems Only..................................... 4
Installation and Operation.................................. 6
Connections........................................................ 6
Power Supply Wiring........................................ 7
TP Cable Termination....................................... 8
Front Panel Power Indicator............................... 10
Skew Delay Problems......................................... 10
Reference Information........................................ 11
Specifications..................................................... 11
Part Numbers..................................................... 13
MTP DA Distribution Amplifier....................... 13
Included Parts................................................ 13
Accessories.................................................... 13
Cables............................................................... 13
Connectors.................................................... 14
Mounting.......................................................... 14
UL Guidelines................................................. 14
Tabletop Use.................................................. 14
Extron Warranty................................................... 15
Contact Information............................................ 15
MTP DA4 and MTP DA8 • Contents
v
MTP DA4 and MTP DA8 • Contents
vi
Introduction
This section introduces the MTP DA4 and MTP DA8. Topics include:
•
About the MTP DA4 and MTP DA8
•
TP Cable Advantages
•
Termination and Mute Jumpering — MTP 15HD Systems Only
About the MTP DA4 and MTP DA8
The Extron MTP DA4 and MTP DA8 twisted pair (TP) distribution amplifiers (DAs) distribute
a single TP input signal to four or eight MTP receivers. The TP input can be from any of the
following MTP transmitter and switcher families:
•
MTP T SV — S-video transmitter (all models)
•
MTP T 15HD A — RGB/high resolution video and audio transmitter (all models)
•
MTP T 15HD RS — RGB/high resolution video and serial link transmitter (all models)
•
SW MTP T 15HD A — Video and audio switcher with built-in TP transmitter
•
VTT001 — RGB/high resolution video transmitter
The MTP DAs are part of a system (see figure 1) used for long-distance distribution of VGA
or other high resolution video. The MTP DAs can also distribute audio or a serial link over
TP cable. The Extron Enhanced Skew-Free™ AV UTP cable is preferred, but Category (CAT) 5
shielded twisted pair (STP), unshielded twisted pair (UTP), and foil shielded twisted pair (FTP)
cable are also acceptable.
UT
TM
E
PU
OUT
8
7
1
2
3
4
5
6
7
8
A
Extron
MTP DA8
Extron
MTP R 15HD A
Twisted Pair DA
6
TS
PU 5
UT
VO
4
A/
Twisted Pair
Receiver
3
2
1
T
PU
V IN
A/
Up To
8 Receivers
R
WE
PO
-
+
12V3A
0.9
X
MA
NO
DIO
AU 2
R
15
ON
1
PU
T
IN
WER
PO
M TP
T
PRE
-PE
15
HD
ON
AU
UT
TP
OU
DIO
OFF
TO
NI
R
MO
WER
PO
V X
12 MA
.5A
T
PU
IN
2
3
4
5
A
6
UT
TP
OU
V X
12 MA
.5A
A
AK
HD
H SYNC +
V SYNC +
C SYNC
SOG
VIDEO
SPARE
M TP
MO
1
Extron
Skew-Free A/V
UTP Cable
TM
Extron
MTP T 15HD A
Twisted Pair
Transmitter
PC
Sound System Plasma/LCD Projector
Figure 1. Typical TP Distribution System
The MTP DA inputs a proprietary signal on an RJ-45 connector, buffers it, and distributes
four or eight identical proprietary signals on RJ-45 connectors.
MTP DA4 and MTP DA8 • Introduction
1
NOTE: The MTP DA does not support the remote power feature of the MTP SV and
VTT001. You will have to power the transmitter and all connected receivers.
A contact closure connector on the rear panel provides the ability to mute individual outputs
or all outputs.
The MTPs ship with external desktop 12 V power supplies that accept 100 to 240 VAC,
50‑60 Hz input.
TP Cable Advantages
Twisted pair cable is smaller, lighter, more flexible, and less expensive than coaxial cable.
Termination of the cable with RJ-45 connectors is simple, quick, and economical.
Transmission Distance
The maximum distance for the entire transmission system is determined by the output
frequency, resolution, and the position of the transmitter Pre-Peak switch (if equipped). The
total recommended distances are not affected by the presence or absence of an MTP DA
in the transmission system. The following sections specify the recommended transmission
distances using Extron Enhanced Skew-Free AV UTP cable or UTP CAT 5 cable, terminated
with CAT 5 rated connectors
NOTES: • It is possible to exceed the recommended distance, however, image quality
may be reduced.
• The recommendations apply to a complete transmission system, which can
include a single transmitter, one or more DAs, and one or more daisy-chained
receivers. For example, the maximum suggested range for 1024 x 768 video is
300 feet with Pre-Peak off in an MTP 15HD system.
• If you are using the DA as part of an MTP 15HD RS (serial data) transmission
system, be aware that the DA routes the serial link one way only (from the
transmitter to the receivers).
• Also, the transmitter and receiver must be jumper configured to pass the
serial link one way only (see the MTP 15HD RS Series User Guide).
The following table specifies the recommended transmission distances and transmitter
Pre‑Peak switch positions for MTP 15HD RGB transmission systems.
Recommended pre-peak switch position and transmission distances
at 60 Hz
Video Format
Pre-Peak Off Pre-Peak On
Composite,
S-video,
Component
Max. Distance
(High Quality)
Max. Distance
(Variable Quality)
800 feet
(245 m)
1,000 feet
(300 m)
640 x 480
<300 feet
(90 m)
>350 feet
(105 m)
700 feet
(215 m)
750 feet
(230 m)
800 x 600
<300 feet
(90 m)
>350 feet
(105 m)
550 feet
(165 m)
650 feet
(200 m)
1024 x 768*
<300 feet
(90 m)
>350 feet
(105 m)
500 feet
(150 m)
600 feet
(185 m)
1280 x 960*
<300 feet
(90 m)
>350 feet
(105 m)
400 feet
(120 m)
500 feet
(150 m)
MTP DA4 and MTP DA8 • Introduction
2
Video Format
Pre-Peak Off Pre-Peak On
Max. Distance
(High Quality)
Max. Distance
(Variable Quality)
1280 x 1024*
<250 feet
(75 m)
>300 feet
(90 m)
350 feet
(105 m)
450 feet
(135 m)
1360 x 765
<250 feet
(75 m)
>300 feet
(90 m)
400 feet
(120 m)
500 feet
(150 m)
1365 x 768
<250 feet
(75 m)
>300 feet
(90 m)
400 feet
(120 m)
450 feet
(135 m)
1366 x 768
<250 feet
(75 m)
>300 feet
(90 m)
400 feet
(120 m)
450 feet
(135 m)
1400 x 1050
<250 feet
(75 m)
>300 feet
(90 m)
350 feet
(105 m)
400 feet
(120 m)
1440 x 900
<250 feet
(75 m)
>300 feet
(90 m)
350 feet
(105 m)
400 feet
(120 m)
1600 x 1200*
<250 feet
(75 m)
>300 feet
(90 m)
300 feet
(90 m)
450 feet
(135 m)
1920 x 1200
<250 feet
(75 m)
>300 feet
(90 m)
300 feet
(90 m)
400 feet
(120 m)
2048 x 1080
<250 feet
(75 m)
>300 feet
(90 m)
300 feet
(90 m)
400 feet
(120 m)
HDTV 720p
<250 feet
(75 m)
>300 feet
(90 m)
400 feet
(120 m)
500 feet
(150 m)
HDTV 1080i
<250 feet
(75 m)
>300 feet
(90 m)
300 feet
(90 m)
400 feet
(120 m)
HDTV 1080p
<250 feet
(75 m)
>300 feet
(90 m)
300 feet
(90 m)
400 feet
(120 m)
NOTE: Resolutions marked with an asterisk (*) in the above table have the same range
specification at 75 Hz.
MTP SV and MTP CV transmission distances
Extron suggests a minimum transmission distance of at least 50 feet (15 m). The maximum
transmission distance is 1000 feet (300 m).
VTT001/VTR001 transmission distances
The following table specifies the maximum recommended transmission distances for a
VTT001/VTR001 system at 60 Hz.
Video Format
Recommended
Video Format
Maximum Range
Recommended
Maximum Range
640 x 480
500 feet
1365 x 768
200 feet
800 x 600
400 feet
1366 x 768
200 feet
1024 x 768*
300 feet
1440 x 900
200 feet
1280 x 960*
200 feet
1400 x 1050
200 feet
1280 x 1024*
200 feet
1600 x 1200*
150 feet
1360 x 765
200 feet
1920 x 1080
150 feet
NOTE: Resolutions marked with an asterisk (*) in the above table have the
same range specification at 75 Hz.
MTP DA4 and MTP DA8 • Introduction
3
Termination and Mute Jumpering —
MTP 15HD Systems Only
NOTE: The position of jumpers J3 and J9 have no effect when the DA is installed as a
part of an MTP SV series or VTT001/VTR001 system.
When an MTP T 15HD A or SW MTP T 15HD A provides the input, the MTP DA output can
include analog audio as well as RGB video. When an MTP T 15HD RS provides the input, the
DA output can include a serial (RS-232) link as well as RGB video.
A jumper block inside the MTP DA sets the DA to properly terminate the audio or serial
portion of the input signal when the input signal is transmitted by an MTP 15HD A series
(audio), SW MTP T (audio), or MTP 15HD RS series (serial) transmitter.
A second jumper block sets the DA to mute the audio or serial link when its video mute
function is activated. The DA can also be set to always pass the audio or serial link regardless
of the contact closure mute status.
By default, the MTP DA is configured with the internal jumpers set to terminate audio
(default). For serial data applications, the DA can be configured to properly terminate the
signal as follows:
1. If applicable, disconnect all cables, remove the DA from its installation location, and
remove any mounting brackets installed (see Mounting on page 14).
2. Remove the two screws from both sides of the DA and the two screws on the top (six
screws total) and lift the top cover off of the DA (see figure 2).
A
A
A
S
S
S
3. Select audio or serial distribution — Locate jumper J3 on the main board and
shift the jumper from the audio (default, on the right) to the serial (left) position (see
figure 2).
Disable or
Mute
(Default)
Serial
or
Enable
Mute
J9
Audio
(Default)
Jumper Block J9
Inside Box
J3
Jumper Block J3
Inside Box
TE
UT
TP
OU
8
7
S
UT
5
1
2
3
4
MU
5
6
7
8
A
6
TP
A/V
4
OU
3
2
1
T
A/V
U
INP
WER
PO
-
+
AX
V
12 A M
0.93
Remove 6 screws,
lift top straight up.
Figure 2.
Opening the DA and Termination Jumpering
MTP DA4 and MTP DA8 • Introduction
4
4. Enable or disable audio or serial distribution mute — If desired, locate jumper J9
on the main board and shift the jumper from the disable mute (default, on the top) to
the enable mute (bottom) position (see figure 2).
NOTES: • When J9 is set to the disable mute (default, on the top) position, the
video mute has no effect on the audio or serial distribution of the DA.
• When J9 is set to the enable mute (bottom) position, the DA mutes the
audio or serial output when its contact closure video mute is activated.
5. Replace the top cover.
6. Reinstall the six screws removed in step 2. If any mounting brackets were removed in
step 1, put them back into position as you reinstall the screws.
7. If applicable, reinstall the DA and reconnect all cables.
MTP DA4 and MTP DA8 • Introduction
5
Installation and
Operation
This section provides information pertaining to the installation and operation of the
MTP DA4 and MTP DA8, including:
•
Connections
•
Power Supply Wiring
•
TP Cable Termination
•
Front Panel Power Indicator
•
Skew Delay Problems
Connections
ATTENTION: Do not connect these devices to a computer data or telecommunications
network.
MTP DA8
A/V INPUT
POWER
1
2
3
A/V OUTPUTS
4
5
6
7
8
- +
12V
0.93A MAX
1
OUTPUT MUTE
1 2 3 4
2
3
5 6 7 8 A
4
MTP DA4
A/V INPUT
POWER
1
A/V OUTPUTS
2
3
4
- +
12V
0.93A MAX
1
OUTPUT MUTE
1 2 3 4 A
2
3
4
Figure 3. MTP DA Rear Panel Features
a Power connector — Plug the included external 12 VDC power supply into this 2-pole
captive screw connector (see Power Supply Wiring on page 7 to wire the connector).
b AV Input connector — Connect one end of the cable carrying the video or
audio/ serial TP link from the transmitting device to this RJ-45 female connector (see
TP Cable Termination on page 8 to wire the RJ-45 connectors).
c AV Output connector — Connect one end of up to four or eight TP cables to these
RJ-45 female connectors.
Connect the free ends of the same cables carrying the distributed video or audio/serial
TP link to the RJ-45 connectors on the receivers (see TP Cable Termination on page 8
to wire the RJ-45 connectors).
MTP DA4 and MTP DA8 • Installation and Operation
6
NOTES: • The MTP DA output does not provide any pre-peaking control. The total
recommended distance for a complex system with multiple DA outputs is
the same as for a simple system with a single transmitter and receiver.
• See the recommended transmission ranges in the table on page 2. The
recommendations in the table apply to a complete transmission system,
which can include a single transmitter, DA, and multiple receivers or a
complex system including multiple daisy-chained receivers.
d Output Mute connections — The Output Mute connector provides a way to mute
(blank) any or all TP outputs. Each numbered pin of the captive screw connector is
assigned to one of the DA outputs. Pin A is assigned to all DA outputs (see figure 4).
When you short and latch a numbered pin or pins to ground, the DA mutes the
associated outputs.
MTP DA8
Output Mute Connector
1 2 3 4
5 6 7 8 A
MTP DA4
Output Mute Connector
1 2 3 4 A
Pin
Contact
Closure
1
Out #1
Mute output #1
2
Out #2
Mute output #2
3
Out #3
Mute output #3
4
Out #4
Mute output #4
5
Out #5
Mute output #5
6
Out #6
Mute output #6
7
Out #7
Mute output #7
8
Out #8
Mute output #8
A
Out All
Mute all outputs
Gnd
Figure 4.
Function
Ground
Mute Connector and Pinout
Power Supply Wiring
Figure 5 shows how to wire the power connector (see the caution, attention, and notes on
the next page before wiring the power connector).
2-Pole Captive Screw
Connector
Tie Wrap
3/16”
(5 mm) Max.
SECTION A–A
Smooth
Ridges
A
A
Power Supply
Output Cord
Figure 5. Power Connector Wiring
MTP DA4 and MTP DA8 • Installation and Operation
7
ATTENTION: Power supply voltage polarity is critical. Incorrect voltage polarity can
damage the power supply and the unit. The ridges on the side of the cord
(see figure 5) identify the power cord negative lead.
To verify the polarity before connection, plug in the power supply with no load and check
the output with a voltmeter.
CAUTION: May cause electric shock. The two power cord wires must be kept
separate while the power supply is plugged in. Remove power before
wiring.
NOTES: • The length of the exposed (stripped) copper wires is important. The ideal
length is 3/16 inch (5 mm). Longer bare wires can short together. Shorter
wires are not as secure in the connectors and could be pulled out.
• Do not tin the power supply leads before installing them in the direct
insertion connector. Tinned wires are not as secure in the connectors and
could be pulled out.
Use the supplied tie wrap to strap the power cord to the extended tail of the connector.
Alternatively, an optional Extron PS 124 Universal 12 VDC Power Supply (part number
60‑1022-01) can power multiple Extron 12 VDC devices using only one AC power
connector.
TP Cable Termination
NOTE: RJ-45 termination with CAT 5, CAT 5e, or CAT 6 cable must comply with the
TIA/EIA T 568A or TIA/EIA T 568B wiring standards for all connections. RJ-45
termination with Skew-Free AV UTP cable must comply with TIA/EIA T 568 A
only.
Figure 6 on the next page details the termination of TP cables with RJ-45 connectors in
accordance with the TIA/EIA T 568A or TIA/EIA T 568B wiring standards. Use either standard
with CAT 5/5e/6 cable, but use the same standard on both ends of the cable.
Note the separate columns for input from a low resolution (composite video or S-video)
and high resolution (RGB video) MTP. Note also the power table that identifies the
unconventional signal assignment when a low resolution MTP unit is jumpered for stereo
audio.
NOTES: • Enhanced Skew-free AV cable is not recommended for Ethernet/LAN
applications.
• This cable is specially designed for compatibility with Extron Twisted Pair
products, wired using the TIA/EIA 568 A standard.
• The green, brown, and blue pairs of this cable have virtually identical lengths
and should be used to transmit RGB, composite video, or S-video signals.
• The orange pair of this cable has a different length and should not be used
to transmit RGB, composite video, or S-video signals.
• If you are using the DA as part of an MTP 15HD RS (serial data) transmission
system, be aware that the DA routes the serial link one way only, from the
transmitter to the receivers.
Also, the transmitter and receiver must be jumper configured to pass the
serial link one way only (see the MTP 15HD RS Series User Guide).
MTP DA4 and MTP DA8 • Installation and Operation
8
NOTE: When the TP input is from a low resolution unit (MTP SV or MTP AV),
the signal assignment depends on the position of signal jumpers in
the transmitter and receiver (see the MTP AV Series User Guide).
Jumpers in Mono Position (Default)
RJ-45
Connector
Side
Pins:
Pin
568 A Wire
Color
568 B Wire
Color
Composite Video
MTP Signal
S-video
MTP Signal
RGB Video, MTP,
VTT/VTR Signal
1
Whitegreen
Whiteorange
Reserved
Chroma (C) +
Red/
V.Sync +
2
Green
Orange
Reserved
Chroma (C) –
Red/
V.Sync –
3
Whiteorange
Whitegreen
Mono audio +
Mono audio +
Mono audio + or
RS-232 +
(MTP 15HD only)
4
Blue
Blue
Video +
Luma (Y) +
5
White-blue
White-blue
Video –
Luma (Y) –
Green –
6
Orange
Green
Mono audio -
Mono audio –
Mono audio – or
RS-232 –
(MTP 15HD only)
7
Whitebrown
Whitebrown
Reserved
Reserved
Blue/
H.Sync +
8
Brown
Brown
Reserved
Reserved
Blue/
H.Sync –
Pin
568 A Wire
Color
568 B Wire
Color
Composite Video
MTP Signal
S-video
MTP Signal
1
Whitegreen
Whiteorange
Video +
Luma (Y) +
2
Green
Orange
Video –
Luma (Y) –
3
Whiteorange
Whitegreen
Reserved
Reserved
4
Blue
Blue
Audio left +
Chroma (C) &
audio left +
5
White-blue
White-blue
Audio left –
Chroma (C) &
audio left –
6
Orange
Green
Reserved
Reserved
7
Whitebrown
Whitebrown
Audio right +
Audio right +
8
Brown
Brown
Audio right –
Audio right –
12345678
Jumpers in Stereo Position
Insert
Twisted
Pair Wires
NOTE: If you are using Enhanced Skew-Free™ AV cable, use the
TIA/EIA T 568A standard only.
Figure 6. TP Cable Termination
MTP DA4 and MTP DA8 • Installation and Operation
9
Front Panel Power Indicator
The Power LED indicates power is applied to the MTP DA (see figure 7).
MTP DA SERIES
Power LED
Figure 7. MTP DA Front Panels
Skew Delay Problems
CAT 5 TP cable can lead to registration errors between the red, green, and blue video
signals. Pair skew can be measured with test equipment or identified by viewing a crosshatch
test pattern with a critical eye to determine if either the red, green, or blue video image
leads (appears to the left of) the other two video images. These images can be minimized or
eliminated by using one of the following methods:
•
Using a skew delay adjusting receiver:
(MTP RL 15HD A SEQ or MTP RL 15HD RS SEQ)
•
Switching to an Extron Enhanced Skew-Free AV UTP cable
•
Adding a skew compensation cable equal to the length of pair skew to the video output
of the receiver
•
Installing an SEQ 100 15HD Skew Equalizer on the video output of the receiver and
adjusting the skew for the leading video image
MTP DA4 and MTP DA8 • Installation and Operation
10
Reference
Information
This section provides reference information, including:
•
Specifications
•
Part Numbers
•
Mounting
Specifications
Video
Gain����������������������������������������������� Unity
Video input — see transmitters specifications
Number/signal type������������������������ 1 set of proprietary analog signals
Connectors������������������������������������ 1 female RJ-45
Video output — see receivers specifications
Number/signal type
MTP DA4��������������������������������� 4 sets of proprietary analog signals
MTP DA8��������������������������������� 8 sets of proprietary analog signals
Connectors
MTP DA4��������������������������������� 4 female RJ-45
MTP DA8��������������������������������� 8 female RJ-45
Maximum resolution���������������������� 2048x1080
NOTE: See the table on page 2 for the maximum distances recommended for specific resolutions.
Audio
Gain����������������������������������������������� Unity (0 dB)
Audio input — see transmitters specifications
Number/signal type������������������������ 1 set of proprietary analog signals
Connectors������������������������������������ 1 female RJ-45
Audio output — see receivers specifications
Number/signal type
MTP DA4��������������������������������� 4 sets of proprietary analog signals
MTP DA8��������������������������������� 8 sets of proprietary analog signals
Connectors
MTP DA4��������������������������������� 4 female RJ-45
MTP DA8��������������������������������� 8 female RJ-45
MTP DA4 and MTP DA8 • Reference Information
11
Control/remote — distribution amplifier
Contact closure (latching)
MTP DA4��������������������������������� (1) 3.5 mm captive screw connector, 6 pole for contact closure output mute
control
MTP DA8��������������������������������� (1) 3.5 mm captive screw connector, 10 pole for contact closure output mute
control
Contact closure pin configurations
MTP DA4��������������������������������� 1 = mute output 1, 2 = mute output 2, 3 = mute output 3, 4 = mute output 4,
5 = mute all outputs, 6 = GND
MTP DA8��������������������������������� 1 = mute output 1, 2 = mute output 2, 3 = mute output 3, 4 = mute output 4,
5 = mute output 5, 6 = mute output 6, 7 = mute output 7, 8 = mute output 8,
9 = mute all outputs, 10 = GND
General
Recommended cable type�������������� Enhanced Skew-Free™ AV UTP Cable or CAT 5/5e/6 (shielded or unshielded)
Power supply���������������������������������� External
Input: 100-240 VAC, 50-60 Hz
MTP DA4��������������������������������� 12 VDC, 1 A, regulated
MTP DA8��������������������������������� 12 VDC, 1 A, regulated
Power input requirements
MTP DA4��������������������������������� 12 V, 0.6 A
MTP DA8��������������������������������� 12 V, 0.9 A
Temperature/humidity�������������������� Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling������������������������������������������ Convection, no vents
Mounting
Rack mount����������������������������� Yes, with optional 1U rack shelf
Furniture mount���������������������� Yes, with optional under-desk mounting kit
Pole mount������������������������������ Yes, with optional pole mounting kit
Enclosure type�������������������������������� Metal
Enclosure dimensions��������������������� 1.75" H x 8.75" W x 6" D (1U high, half rack wide)
(4.4 cm H x 22.2 cm W x 15.2 cm D)
(Depth excludes connectors.)
Product weight������������������������������� 1.2 lbs (0.5 kg)
Shipping weight����������������������������� 4 lbs (2 kg)
Vibration���������������������������������������� ISTA 1A in carton (International Safe Transit Association)
Regulatory compliance
Safety�������������������������������������� CE, c-UL, UL
EMI/EMC��������������������������������� CE, C-tick, FCC Class A, ICES, VCCI
Environmental�������������������������������� Complies with the appropriate requirements of RoHS, WEEE
MTBF��������������������������������������������� 30,000 hours
Warranty���������������������������������������� 3 years parts and labor
NOTE: All nominal levels are at ±10%.
NOTE: Specifications are subject to change without notice.
MTP DA4 and MTP DA8 • Reference Information
12
Part Numbers
MTP DA Distribution Amplifier
DA
Part Number
MTP DA4
60-685-01
MTP DA8
60-686-01
Included Parts
These items are included in each order for MTP DA4 and MTP DA8:
Included Parts
Part Number
12 VDC power supply
MTP DA4
MTP DA8
28-071-57LF
MTP DA Series Setup Guide
IEC power cord
Rubber feet
Tweeker
Accessories
Accessory
Part Number
PS 124 multi output 12 V power supply
60-1022-01
RSU 129 1U universal rack shelf
60-190-01
RSB 129 1U basic rack shelf
60-604-02
RSU 126 6” deep universal rack shelf kit
60-190-10
RSB 126 6” deep basic rack shelf
60-604-11
MBU 125 low-profile mount kit
70-077-01
PMK 200 pole mount kit
70-077-04
SEQ 100 15HD skew equalizer
60-676-01
Cables
NOTE: Enhanced Skew-Free™ AV UTP cables are not
recommended for Ethernet/LAN applications.
Enhanced Skew-Free AV Cable
Part Number
Enhanced Skew-Free AV cable
(cut, various lengths)
26-569-xx
Enhanced Skew-Free AV 1000 feet
(Bulk) (non-plenum)
22-141-03
Plenum enhanced Skew-Free AV 1000
feet (Bulk)
22-142-03
MTP DA4 and MTP DA8 • Reference Information
13
Connectors
Connector
Part Number
CAT 6 jack (black), qty. 10
100-476-01
CAT 6 jack (red), qty. 10
100-477-01
CAT 6 jack (blue), qty. 10
100-478-01
CAT 6 jack (orange), qty. 10
100-479-01
CAT 6 jack (gray), qty. 10
100-480-01
CAT 6 jack (white), qty. 10
100-481-01
CAT 6 jack (ivory), qty. 10
100-482-01
Mounting
CAUTION: Installation and service must be performed by authorized personnel only.
The 1U high, half rack width MTP DA can be set on a table, mounted on a rack shelf,
mounted to a rack without a shelf, or mounted under a desk or tabletop.
NOTE: For rack or furniture mount installation, see the installation card that comes in
the kit.
UL Guidelines
The following Underwriters Laboratories (UL) requirements pertain to the installation of the
DA into or onto a rack.
1. Elevated operating ambient — If installed in a closed or multi-unit rack assembly,
the operating ambient temperature of the rack environment may be greater than room
ambient. Therefore, consider installing the equipment in an environment compatible
with the +122 °F (+50 °C) maximum ambient temperature (TMA) specified by Extron.
2. Reduced air flow — Installation of the equipment in a rack should be such that the
amount of air flow required for safe operation of the equipment is not compromised.
3. Mechanical loading — Mounting of the equipment in the rack should be such that a
hazardous condition is not achieved due to uneven mechanical loading.
4. Circuit overloading — Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits might
have on overcurrent protection and supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
5. Reliable earthing (grounding) — Reliable earthing of rack-mounted equipment
should be maintained. Particular attention should be given to supply connections (such
as the use of power strips) other than direct connections to the branch circuit.
Tabletop Use
Four self-adhesive rubber feet are included with the DA. For tabletop use, attach one foot to
each corner of the bottom side of the unit and place the unit in the desired location.
MTP DA4 and MTP DA8 • Reference Information
14
Extron Warranty
Extron Electronics warrants this product against defects in materials and workmanship for a period of three years
from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty
workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is
returned within the warranty period, with proof of purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron Electronics
1001 East Ball Road
Anaheim, CA 92805
U.S.A.
Japan:
Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
Europe, Africa, and the Middle
East:
Extron Europe
Hanzeboulevard 10
3825 PH Amersfoort
The Netherlands
China:
Extron China
686 Ronghua Road
Songjiang District
Shanghai 201611
China
Asia:
Extron Asia
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363
Singapore
Middle East:
Extron Middle East
Dubai Airport Free Zone
F12, PO Box 293666
United Arab Emirates, Dubai
This Limited Warranty does not apply if the fault has been caused by misuse, improper handling care, electrical
or mechanical abuse, abnormal operating conditions, or modifications were made to the product that were not
authorized by Extron.
NOTE: If a product is defective, please call Extron and ask for an Application Engineer to receive an RA (Return
Authorization) number. This will begin the repair process.
USA: 714.491.1500 or 800.633.9876
Asia:65.6383.4400
Europe:31.33.453.4040
Japan:81.3.3511.7655
Units must be returned insured, with shipping charges prepaid. If not insured, you assume the risk of loss or damage
during shipment. Returned units must include the serial number and a description of the problem, as well as the
name of the person to contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality,
performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct,
indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some provisions of this warranty may
not apply to you.
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West
Extron USA - East
+1.714.491.1500+1.919.850.1000
+1.714.491.1517 FAX
+1.919.850.1001 FAX
Extron Europe
+800.3987.6673
(Inside Europe Only)
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
(Inside Asia Only)
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+4000.398766
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
© 2012 Extron Electronics All rights reserved. www.extron.com
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
Inside India Only
+91.80.3055.3777
+91.80.3055.3737 FAX
Download PDF