Chicago Electric | 67707 | Operating instructions | Chicago Electric 67707 Operating instructions

12V Lithium-Ion
Multifunction Tool
Model 67707
Set up and Operating Instructions
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
Save this manual.
Copyright© 2010 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
NOTICE is used to
address practices not
related to personal injury.
Save This Manual
Keep this manual for the safety warnings
and precautions, assembly, operating,
inspection, maintenance and cleaning
procedures. Write the product’s serial number
in the back of the manual near the assembly
diagram (or month and year of purchase if
product has no number). Keep this manual
and the receipt in a safe and dry place for
future reference.
CAUTION, without the
safety alert symbol, is
used to address practices not
related to personal injury.
General Power Tool Safety Warnings
WARNING Read all safety warnings
and instructions. Failure to follow the
warnings and instructions may result
in electric shock, fire and/or serious
injury.
Save all warnings and instructions
for future reference.
The term ″power tool″ in the warnings
refers to your battery-operated
(cordless) Multifunction Tool.
Important SAFETY
Information
In this manual, on the labeling, and
all other information provided with
this product:
This is the safety alert
symbol. It is used to alert
you to potential personal
injury hazards. Obey all
safety messages that follow
this symbol to avoid possible
injury or death.
1.
a.Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b.Do not operate power tools in
explosive atmospheres, such as in
the presence of flammable liquids,
gases or dust. Power tools create
sparks which may ignite the dust or
fumes.
DANGER indicates a
hazardous situation
which, if not avoided, will result
in death or serious injury.
WARNING indicates a
hazardous situation
which, if not avoided, could
result in death or serious injury.
c. Keep children and bystanders
away while operating a power tool.
Distractions can cause you to lose
control.
CAUTION, used with
the safety alert
symbol, indicates a hazardous
situation which, if not avoided,
could result in minor or moderate
injury.
Page 2
Work area safety
2.
Electrical safety
Do not expose power tools to rain or
wet conditions. Water entering a power
tool will increase the risk of electric
shock.
3.
Personal safety
a.Stay alert, watch what you are
doing and use common sense when
operating a power tool. Do not use
For technical questions, please call 1-800-444-3353.
SKU 67707
a power tool while you are tired or
under the influence of drugs, alcohol
or medication. A moment of inattention
while operating power tools may result
in serious personal injury.
4.
a.Do not force the power tool. Use
the correct power tool for your
application. The correct power tool will
do the job better and safer at the rate
for which it was designed.
b.Use personal protective equipment.
Always wear eye protection. Safety
equipment such as a dust mask,
non-skid safety shoes, a hard hat, or
hearing protection used for appropriate
conditions will reduce personal injuries.
b.Do not use the power tool if the
Power Switch does not turn it on
and off. Any power tool that cannot
be controlled with the power switch is
dangerous and must be repaired.
c. Prevent unintentional starting.
Ensure the Power Switch is in the offposition before connecting to power
source and/or battery pack, picking
up or carrying the tool. Carrying
power tools with your finger on the
power switch invites accidents.
d.Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to any part
of the power tool may result in personal
injury.
e.Do not overreach. Keep proper
footing and balance at all times. This
enables better control of the power tool
in unexpected situations.
f. Dress properly. Do not wear loose
clothing or jewelry. Keep your hair,
clothing and gloves away from
moving parts. Loose clothes, jewelry
or long hair can be caught in moving
parts.
g.Only use safety equipment that has
been approved by an appropriate
standards agency. Unapproved
safety equipment may not provide
adequate protection. Eye protection
must be ANSI-approved and breathing
protection must be NIOSH-approved for
the specific hazards in the work area.
SKU 67707
Power tool use and care
c. Disconnect the battery pack from
the power tool before making any
adjustments, changing accessories,
or storing power tools. Such
preventive safety measures reduce
the risk of starting the power tool
accidentally.
5.
Hold the power tool by insulated
gripping surfaces when performing an
operation where the cutting tool may
contact hidden wiring. Contact with a
″live″ wire will make exposed metal parts
of the tool ″live″ and shock the operator.
6.
Use clamps or another practical way
to secure and support the work piece
to a stable platform. Holding the work
by hand or against your body leaves it
unstable and may lead to loss of control.
a.Store idle power tools out of reach
of children and do not allow persons
unfamiliar with the power tool or
these instructions to operate the
power tool. Power tools are dangerous
in the hands of untrained users.
b.Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any
other condition that may affect the
power tool’s operation. If damaged,
have the power tool repaired before
use. Many accidents are caused by
poorly maintained power tools.
For technical questions, please call 1-800-444-3353.
Page 3
7.
c. Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to
bind and are easier to control.
1.
d.Use the power tool and accessories
in accordance with these
instructions, taking into account the
working conditions and the work
to be performed. Use of the power
tool for operations different from those
intended could result in a hazardous
situation.
Maintain labels and nameplates on
the tool. These carry important safety
information. If unreadable or missing,
contact Harbor Freight Tools for a
replacement.
2.
Do not use this Multifunction Tool with
any other Battery or Charger.
3.
Avoid unintentional starting. Prepare to
begin work before turning on the tool.
4.
CAUTION: Avoid accidental injury. Keep
hands and fingers safely away from the
oscillating Scraper, Cutting Blade, and
Sandpaper when operating the tool.
5.
Avoid unintentional starting. Prepare to
begin work before turning on the power
tool.
6.
Do not lay the tool down until it has come
to a complete stop. Moving parts can
grab the surface and pull the tool out of
your control.
7.
When using a handheld power tool,
maintain a firm grip on the tool with both
hands to resist starting torque.
8.
Do not leave the tool unattended when
the battery pack it installed. Turn off the
tool, and remove the battery pack before
leaving.
9.
The battery pack and Charger
get hot during use. The
pack’s heat can build up to
unsafe levels and create a fire
hazard if it does not receive adequate
ventilation, due to an electrical fault, or if
it is used in a hot environment.
Do not place the Battery Pack on a
flammable surface. Do not obstruct any
vents on the Battery Pack. Especially
avoid placing the Battery Pack on
carpets and rugs; they are not only
Battery tool use and care
a.Recharge only with the Charger
specified by the manufacturer. A
Charger that is suitable for one type of
battery pack may create a risk of fire
when used with another battery pack.
b.Use power tools only with
specifically designated battery
packs. Use of any other battery packs
may create a risk of injury and fire.
c. When battery pack is not in use, keep
it away from other metal objects,
like paper clips, coins, keys, nails,
screws or other small metal objects,
that can make a connection from
one terminal to another. Shorting the
battery terminals together may cause
burns or a fire.
d.Under abusive conditions, liquid
may be ejected from the battery;
avoid contact. If contact accidentally
occurs, flush with water. If liquid
contacts eyes, additionally seek
medical help. Liquid ejected from the
battery may cause irritation or burns.
8.
Service
a.Have your power tool serviced by a
qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power tool
is maintained.
Page 4
Multifunction Tool Safety Warnings
For technical questions, please call 1-800-444-3353.
SKU 67707
flammable, but they also obstruct
vents under the Battery Pack.
Place the Battery Pack on a stable, solid,
nonflammable surface (such as a stable
metal workbench or concrete floor) at
least 1 foot away from all flammable
objects, such as drapes or walls. Keep a
fire extinguisher and a smoke detector in
the area. Frequently monitor the Battery
Pack and Charger while charging.
10. This product is not a toy. Keep it out of
reach of children.
11. People with pacemakers should
consult their physician(s) before use.
Electromagnetic fields in close proximity
to heart pacemaker could cause
pacemaker interference or pacemaker
failure. In addition, people with
pacemakers should:
• Avoid operating alone.
• Do not use with power switch locked
on.
• Properly maintain and inspect to avoid
electrical shock.
12. WARNING: Some dust created by power
sanding, sawing, grinding, drilling, and
other construction activities, contains
chemicals known [to the State of
California] to cause cancer, birth defects
or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and
cement or other masonry products
• Arsenic and chromium from chemically
treated lumber
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to
these chemicals: work in a well ventilated
area, and work with approved safety
equipment, such as those dust masks
that are specially designed to filter out
SKU 67707
microscopic particles. (California Health
& Safety Code § 25249.5, et seq.)
13. WARNING: Handling the Charger cord
on this product will expose you to lead, a
chemical known to the State of California
to cause cancer, and birth defects or
other reproductive harm. Wash hands
after handling. (California Health &
Safety Code § 25249.5, et seq.)
14. The warnings, precautions, and
instructions discussed in this instruction
manual cannot cover all possible
conditions and situations that may occur.
It must be understood by the operator
that common sense and caution are
factors which cannot be built into this
product, but must be supplied by the
operator.
Lithium Battery Safety Warnings
Lithium batteries store a
large amount of energy and
will vent fire or explode if
mistreated:
1.
Keep Battery Pack dry.
2.
Do not do any of the
following to the battery pack:
a.Open,
b.Drop,
c. Short-circuit,
d.Incinerate, or
e.Expose to temperatures greater than
140°F.
3.
Charge Battery Pack only according to
the instructions in this manual.
For technical questions, please call 1-800-444-3353.
Page 5
4.
Inspect Battery Pack before every use;
do not use or charge if damaged.
abnormal vibration occurs, stop use
immediately.
Save these
instructions.
Vibration Safety
This tool vibrates during use. Repeated
or long-term exposure to vibration may
cause temporary or permanent physical
injury, particularly to the hands, arms
and shoulders. To reduce the risk of
vibration-related injury:
1.
Anyone using vibrating tools regularly
or for an extended period should first
be examined by a doctor and then have
regular medical check-ups to ensure
medical problems are not being caused
or worsened from use. Pregnant
women or people who have impaired
blood circulation to the hand, past hand
injuries, nervous system disorders,
diabetes, or Raynaud’s Disease
should not use this tool. If you feel any
symptoms related to vibration (such as
tingling, numbness, and white or blue
fingers), seek medical advice as soon as
possible.
2.
Do not smoke during use. Nicotine
reduces the blood supply to the hands
and fingers, increasing the risk of
vibration-related injury.
3.
Wear suitable gloves to reduce the
vibration effects on the user.
4.
Use tools with the lowest vibration when
there is a choice.
5.
Include vibration-free periods each day
of work.
6.
Grip tool as lightly as possible (while still
keeping safe control of it). Let the tool
do the work.
7.
To reduce vibration, maintain the tool
as explained in this manual. If any
Page 6
Grounding
To prevent
electric shock
and death from incorrect
grounding wire
connection:
Check with a qualified electrician
if you are in doubt as to whether
the outlet is properly grounded.
Do not modify the Charger cord
plug provided with the tool.
Never remove the grounding
prong from the plug. Do not use
the tool if the power cord or plug
is damaged. If damaged, have it
repaired by a service facility
before use. If the plug will not fit
the outlet, have a proper outlet
installed by a qualified
electrician.
Double Insulated Tools: Tools with
Two Prong Plugs
Outlets for 2-Prong Plug
1.
Tools marked “Double Insulated” do not
require grounding. They have a special
double insulation system which satisfies
OSHA requirements and complies with
For technical questions, please call 1-800-444-3353.
SKU 67707
the applicable standards of Underwriters
Laboratories, Inc., the Canadian
Standard Association, and the National
Electrical Code.
2.
Double insulated tools may be used in
either of the 120 volt outlets shown in the
preceding illustration. (See Outlets for
2-Prong Plug.)
Extension Cords
Note: Extension cords must not be used with
this item’s Charger.
Symbology
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
V~
A
Volts Alternating Current
Amperes
No Load Revolutions per Minute
n0 xxxx/min. (RPM)
SKU 67707
For technical questions, please call 1-800-444-3353.
Page 7
assembling or making any
adjustments to the tool.
Specifications
Charger Input
120 VAC
Battery Type
12 V Lithium, 1.3 Ah
Motor Speed
15,000 OPM (No Load)
Accessories
Sandpaper (2 pieces for wood
and 2 pieces for metal)
Sanding Pad
Cutting Blade
Scraper Blade
Hex Wrench
Note: For additional information regarding the
parts listed in the following pages, refer
to the Assembly Diagram near the end of
this manual.
Components
Unpacking
When unpacking, make sure that the
item is intact and undamaged. If any parts
are missing or broken, please call Harbor
Freight Tools at 1-800-444-3353 as soon as
possible.
Accessory Attachments - This multipurpose tool includes Sandpaper (504) and
a Sanding Pad (503) for sanding wood or
removing paint from surfaces, a Cutting
Blade (502) to cut wood and soft metal such
as copper piping, and a Scraper Blade (501)
which can be used for scraping paint or wall
paper from flat surfaces.
Instructions for putting
into use
Battery
Pack
Case (507)
Tool
Scraper Blade
(501)
Hex
Wrench
(505)
Read the entire Important
Safety Information
section at the beginning of this
manual including all text under
subheadings therein before set up
Figure 1
or use of this product.
To prevent
serious injury
from accidental
operation:
Turn the Power Switch off and
remove the Battery Pack before
Page 8
Sanding
Pad
(503)
Cutting Blade
(502)
Charger
(506)
Sandpaper
(504)
Set up
Read the entire Important
Safety Information
section at the beginning of this
manual including all text under
subheadings therein before set up
or use of this product.
For technical questions, please call 1-800-444-3353.
SKU 67707
Work Piece and Work Area Set Up
1.
2.
Designate a work area that is clean and
well-lit. The work area must not allow
access by children or pets to prevent
distraction and injury.
Route the power cord of the Charger
along a safe route without creating a
tripping hazard or exposing the power
cord to possible damage.
5.
Note: Do not use a battery pack immediately
after charging. Allow it to cool first. Store
the Charger and Battery Packs not in
use indoors, away from children.
Installing Attachments
To prevent
serious injury
from accidental
operation:
Make sure the Battery Pack is
removed from the Tool before
installing accessories, or
adjusting the tool.
Charging the Battery Pack
The Battery Pack needs to be charged
before first use. It is recommended to
recharge the Battery after every use.
Charger (506)
Indicator Light
1.
Charger Plug
Figure 2
Charger
Socket
Battery
Pack
1.
Place the Battery Pack on a dry fireproof
surface in a room where the temperature
ranges from 33-112° F.
2.
Allow a recently exhausted Battery Pack
to cool completely before charging. Make
sure the Battery Pack is undamaged; do
not charge a cracked or leaking pack.
3.
4.
Insert the Charger’s plug into the
Charger Socket on the Battery Pack, and
plug the Charger into a grounded, 120V
outlet. The indicator light on the Charger
will turn red showing that the battery is
charging.
Unplug the Battery Pack from the
Charger and the Charger from the wall
outlet.
To install an accessory:
a.Hold the Spindle (3) with a 13mm
wrench (sold separately), and unthread
the Cap Screw (1) using the Hex
Wrench (505). Remove the Cap Screw
and Retainer (2).
Cutting Blade
(502)
Four Pins on
Spindle (3)
Figure 3
b.Install the desired accessory in any one
of seven forward orientations by aligning
four of the holes in the accessory over
the four pins on the Spindle.
CAUTION: Always face the accessory away
from the handle to avoid injury.
When the indicator light turns green,
the Battery Pack is fully charged. This
process will take approximately 90
minutes.
SKU 67707
For technical questions, please call 1-800-444-3353.
Page 9
Scraper Blade (501)
Cap Screw (1)
Figure 4
General Operating Instructions
Spindle (3)
1.
Secure loose work pieces using a vise
or clamps (not included) to prevent
movement while working.
2.
Install desired accessory.
OFF
Retainer (2)
Note: When attaching the angled Cutting
Blade (502) or Scraper Blade (501),
orient the accessory as shown in Figure
4 above, so the Cap Screw (1) will be out
of the way when working.
c. Replace the Retainer and Cap Screw
while holding the accessory. Hold the
Spindle with the wrench, then tighten
securely using the Hex Wrench.
CAUTION: Make sure that the accessory is
held securely in place by the four pins
on the Spindle as you tighten the Cap
Screw.
Power Switch
(26)
Figure 5
3.
Make sure the Power Switch (26) is OFF.
Tool Body
Battery
Button (31)
Note: For sanding, first attach the Sanding
Pad (503) to the tool, then align a sheet
of Sandpaper (504) over the pad and
press into place.
Figure 6
4.
Battery Pack
Once the Battery Pack is fully charged,
slide it into the back of housing until it
clicks into place.
Note: The Battery Pack fits into the Tool
housing only one way. Match up the
shape of the tool with the shape of the
housing opening. The Battery Pack
should slide easily into the housing. Do
not force it into the Tool.
Page 10
For technical questions, please call 1-800-444-3353.
SKU 67707
ON
Power Switch
(26)
Figure 7
5.
While holding the Tool with both hands,
slide the Power Switch (26) forward to
activate.
6.
Do not allow contact between
Sandpaper, Scraper, or Blade and
workpiece until tool is at full speed.
7.
Avoid contact with foreign objects such
as metal screws and nails when sanding,
scraping, or cutting.
8.
Do not apply excessive pressure on the
Tool. Allow the Tool to do the work.
OFF
Power Switch
(26)
Figure 8
9.
When finished using, slide the Power
Switch (26) OFF. Allow the tool to stop
completely before setting it down.
10. Squeeze the Battery Buttons (31) on the
side of the Battery Pack and slide the
Battery Pack out of the Tool Body.
11. Remove the attachment and wipe clean.
12. Store the Tool and accessories in the
Case (507), out of reach of children.
SKU 67707
For technical questions, please call 1-800-444-3353.
Page 11
Maintenance And
Servicing
or Battery Pack. Keep Charger and
Battery Pack dry.
Procedures not specifically
explained in this manual must
be performed only by a qualified
technician.
To prevent
serious injury
from accidental
operation:
Turn the Power Switch off and
remove the Battery Pack from the
tool before performing any
inspection, maintenance, or
cleaning procedures. Unplug the
Charger before performing any
inspection, maintenance or
cleaning procedures.
To prevent serious injury
from tool failure:
Do not use damaged equipment.
If abnormal noise or vibration
occurs, have the problem
corrected before further use.
1.
BEFORE EACH USE, inspect the
general condition of the tool. Check for
loose screws, misalignment or binding of
moving parts, cracked or broken parts,
damaged Charger electrical wiring, and
any other condition that may affect its
safe operation. Sandpaper should not be
dull or contain excessive debris build-up.
Scraper and Cutting Blade should be
clean and sharp.
2.
After Use, wipe external surfaces of
the tool with clean cloth.
3.
WARNING! Do not use if either
the Battery Pack or Charger (506) are
damaged in any way.
4.
Dispose of Battery Pack properly. Do
not short, incinerate or open Charger
Page 12
For technical questions, please call 1-800-444-3353.
SKU 67707
Troubleshooting
Problem
Tool will not start.
Possible Causes
Likely Solutions
1. Battery Pack needs charging
1. Charge Battery Pack.
2. Battery Pack not properly seated. 2. Check that Battery Pack is fully inserted into tool
so that it snaps into place.
3. Connection to Battery Pack
3. Check that the terminals inside the tool are not
damaged.
bent or missing. Have repaired by a qualified
technician if needed.
Tool operates slowly. 1. Battery Pack needs charging.
1. Charge Battery Pack.
2. Job is for a more powerful tool.
2. Use a stronger powered tool.
Performance
1. Accessory dull or damaged.
1. Keep cutting accessories sharp. Replace as
decreases over time.
needed. Replace sandpaper when it becomes
worn or torn.
Excessive noise or Internal damage or wear.
Have technician service tool.
rattling.
Overheating.
1. Forcing tool to work too fast.
1. Allow tool to work at its own rate.
2. Accessory misaligned.
2. Check and correct accessory to fence and/or
table alignment.
3. Accessory dull or damaged.
3. Keep cutting accessories sharp. Replace as
needed. Replace sandpaper when it becomes
worn or torn.
4. Blocked motor housing vents.
4. Wear ANSI-approved safety goggles and NIOSHapproved dust mask/respirator while blowing dust
out of motor using compressed air.
Follow all safety precautions whenever diagnosing or servicing the tool.
Disconnect power supply before service.
PLEASE READ THE FOLLOWING CAREFULLY
The manufacturer and/or distributor has provided the parts list and assembly
diagram in this manual as a reference tool only. Neither the manufacturer or
distributor makes any representation or warranty of any kind to the buyer that he
or she is qualified to make any repairs to the product, or that he or she is qualified
to replace any parts of the product. In fact, the manufacturer and/or distributor
expressly states that all repairs and parts replacements should be undertaken by
certified and licensed technicians, and not by the buyer. The buyer assumes all risk
and liability arising out of his or her repairs to the original product or replacement
parts thereto, or arising out of his or her installation of replacement parts thereto.
SKU 67707
For technical questions, please call 1-800-444-3353.
Page 13
Parts List & ASSEMBLY DIAGRAM
Part
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Description
Cap Screw M8 x 12
Retainer
Spindle
Rubber Casing
Circlip for shaft 26
Spring Washer
Bearing 6000
Block
Bushing
Screw ST4 x 20
Reducer
Circlip for Shaft 4
Bearing 625
Shaft
Bearing 608
Screw M3 x 18
Seal Packing Collar
Middle Cover
Seal Packing Collar
Motor
Trigger
Spring
Right Housing
Page 14
Qty
1
1
1
1
1
1
1
1
1
4
1
1
1
1
1
2
2
1
2
1
1
1
1
Part
24
26
27
28
29
30
31
32
33
34
35
36
37
38
39
41
501
502
503
504
505
506
507
Description
Left Housing
Power Switch
Screw ST3.2 x 14
Electrical Contact
Screw ST3.2 x 14
Battery Cover (Front)
Battery Button
Button Spring
Pole End Plate
Battery (Li-ion) 12V
Protection Board
Charging Port
Screw ST2 x 8
Charging Indicator
Battery Cover (End)
Screw ST3.2 x 14
Scraper Blade
Cutting Blade
Sanding Pad
Sandpaper
Hex Wrench
Charger
Case (not shown)
For technical questions, please call 1-800-444-3353.
Qty
1
1
2
1
4
1
2
2
1
1
1
1
4
1
1
3
1
1
1
4
1
1
1
SKU 67707
LIMITED 90 DAY WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality
and durability standards, and warrants to the original purchaser that this product is free from
defects in materials and workmanship for the period of 90 days from the date of purchase. This
warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or
accidents, repairs or alterations outside our facilities, criminal activity, improper installation,
normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,
injuries to persons or property, or for incidental, contingent, special or consequential damages
arising from the use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may not apply to
you. This warranty is expressly in lieu of all other warranties, express
or implied, including the warranties of merchantability and fitness.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the complaint
must accompany the merchandise. If our inspection verifies the defect, we will either repair or
replace the product at our election or we may elect to refund the purchase price if we cannot
readily and quickly provide you with a replacement. We will return repaired products at our
expense, but if we determine there is no defect, or that the defect resulted from causes not
within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which
vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available
individually as replacement parts.
SKU 67707
For technical questions, please call 1-800-444-3353.
Page 15
Download PDF