INSTALLATION
L.E.D. REAR REFLECTOR CONVERSION for GL 1800
PARTS INCLUDED
1
1
1
1
2
1
Rear Reflector Conversion
Dielectric Grease
Adapter Harness
Black Nylon Male Connector Housing
4” Black Nylon Cable Ties
Installation Instructions
Please read and understand entire instructions before starting installation.
THANK YOU FOR CHOOSING KϋRYAKYN!
IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY AND/OR
PROPERTY DAMAGE OR LOSS, PLEASE PAY CLOSE ATTENTION TO ALL
INSTRUCTIONS, WARNINGS, CAUTIONS AND ATTENTION NOTES REGARDING
THE USE AND CARE OF THIS PRODUCT.
WARNING!
THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING
THE CONTENTS DESCRIBED HEREIN CAN RESULT IN
POTENTIAL DEATH OR SERIOUS INJURY.
ATTENTION! This indication alerts you to the fact that ignoring the contents
described herein may negatively affect product performance and
functionality.
CAUTION!
This indication alerts you to the fact that ignoring the contents
described herein can result in potential injury or material
damage.
TOOLS SUGGESTED
Set of Metric Hex wrenches, Set of Metric combination Wrenches, Drill and Drill Bits
STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE THE
PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS.
STEP 1
Read and understand all steps in the instructions before starting the
installation. Park the motorcycle on a hard, level surface and turn off the
ignition.
CAUTION!
Avoid potential electrical shock! Disconnect the battery before
starting this procedure.
STEP 2
Remove the four fasteners that secure the rear license plate panel. Some
earlier models may have a fifth
OLDER BIKES HAVE FIFTH FASTENER
PIC 1
fastener behind the license plate.
Gently pull off the back panel exposing
the wiring harness. (Red and Blue
plugs). PIC 1 If the bike is equipped
with a trailer hitch, it may be helpful to
remove the receiver before removing
REMOVE THESE FASTENERS
the rear fender.
7456
CUSTOMER SERVICE
877.370.3604 (toll free)
INSTALLATION QUESTIONS
[email protected]
or call 715.247.2983
LIMITED WARRANTY
Küryakyn warrants that any Küryakyn products
sold hereunder, shall be free of defects in
materials and workmanship for a period of one
(1) year from the date of purchase by the
consumer excepting the following provisions:
● Küryakyn shall have no obligation in the event
the customer is unable to provide a receipt
showing the date the customer purchased the
product(s).
●The product must be properly installed,
maintained and operated under
normal conditions.
●Küryakyn makes no warranty, expressed or
implied, with respect to any gold plated
products.
●Küryakyn shall not be liable for any
consequential and incidental damages, including
labor and paint, resulting from failure of a
Küryakyn product, failure to deliver, delay in
delivery, delivery in nonconforming condition, or
for any breech of contract or duty between
Küryakyn and a customer.
●Küryakyn products are often intended for use in
specific applications. Küryakyn makes no
warranty if a Küryakyn product is used in
applications other than intended.
●Küryakyn electrical products are warranted for
one (1) year from the date of purchase by the
consumer. L.E.D.’S contained in components of
Küryakyn products will be warranted for defects
in materials and workmanship for 3 years from
the date of purchase where as all other
components shall be warranted for one(1) year.
This includes, but is not limited to; control
modules, wiring, chrome & other components.
●Küryakyn makes no warranty of any kind in
regard to other manufacturer¹s products
distributed by Küryakyn. Küryakyn will pass on
all warranties made by the manufacturer and
where possible, will expedite the claim on behalf
of the customer, but ultimately, responsibility for
disposition of the warranty claim lies
with the manufacturer.
ABOUT OUR CATALOG
;cont.;
7456921GL90911
For purchasing Küryakyn® products, you
can receive a complete catalog free of charge.
Send the Proof9of9Purchase below with
your address to: Küryakyn, P.O. Box 339,
Somerset, WI 54025.
Please indicate either Accessories Catalog for
Harley9Davidson® or GL & Metric Cruisers.
Be sure to ask your local dealer about other
Küryakyn® products, the motorcycle parts and
accessories designed for riders by riders.
©2005 Küryakyn USA® All Rights
reserved.
kuryakyn.con
STEP 3
Locate the wiring bundle on the horizontal saddlebag support. Release the catch on the large black
nylon cable tie securing the bundle to the saddlebag support and gently pull the wiring from the
protective sheath. Unplug both pairs of blue connectors (PIC.2) and plug the adapter harness
“inline” between them (PIC.3), or inline with an existing adapter harness on the blue connectors.
NOTE: If you have an existing Kuryakyn LED accessory light installed on the
PIC 2
rear of the motorcycle and do not want to install a second harness
adapter, you may use Kuryakyn Part Number 7302, Multi Plug and Play
harness with the existing harness adapter to gain the plug;in for the LED
Rear Reflector Conversion.
ATTENTION! Küryakyn recommends the use of dielectric grease on electrical
connections.
STEP 4
Neatly package the wiring bundle and tuck it back into its protective sheath being
sure to leave the red, white, and black pigtails exposed. Re9attach the stock black
nylon cable tie to hold the bundle in place.
STEP 5
Use a wrench to remove the stock reflector from the rear fender.
STEP 6
Using a 7/32” drill bit, enlarge the existing indexing hole located just right of the
mounting stud hole. This will allow clearance for the light’s wiring.
STEP 7
Install the L.E.D. Rear Reflector Conversion assembly. When feeding the wiring
through its hole take care not to damage the metal connectors crimped to the end
of each wire. Secure the unit with the M5 nut and flat washer provided.
STEP 8
Put a dab of dielectric grease in the front end of the black nylon male connector
and plug it into one of the pigtails coming from the adapter harness.
PIC 3
ATTENTION! Küryakyn recommends the use of dielectric grease on electrical connections.
STEP 9
Support the rear fender so that the wires easily reach the adapter harness (PIC.4). PIC 4
Insert the wires into the exposed end of the male connector you just installed in
the pigtail. Be careful to match red to red, black to black, and white to white
(PIC.5). Check each wire to make sure it is secure; if any did not “latch” when
inserted, carefully bend the metal connector’s lock tab up slightly so it will catch
when inserted into the male connector.
STEP 10
Secure the wire from the L.E.D. Reflector Conversion with the nylon cable ties
provided to prevent contact with the rear tire.
ATTENTION! Secure all wiring away from any moving parts, pinch points or extreme
heat. Küryakyn WILL NOT issue a warranty on any electrical component
that fails due to pinched, crimped, broken, abraded, melted or frayed wires.
STEP 11
Snap the rear fender back in place and reinstall the four (five if an older model)
fasteners removed in Step 2. The fastener with the longest threads (if an older
model) belongs in the center location.
STEP 12
Reinstall the license plate. Reconnect the battery, test all lights.
WARNING!
ENSURE PROPER LIGHT OPERATION BEFORE RIDING THE
MOTORCYCLE. VISIBILITY IS A MAJOR CONCERN FOR
MOTORCYCLISTS. A LIGHTING MALFUNCTION COULD RESULT IN
DEATH OR SERIOUS INJURY.
PIC 5
ATTENTION! It is the installer’s responsibility to ensure that all of the fasteners
(including pre;assembled) are tightened before operation of the
motorcycle. Küryakyn will not issue a warranty on components lost due to improper
installation. Periodic maintenance may be required.
PAGE
2
Ride On!
L.E.D. REAR REFLECTOR
INSTALLATION
">
