SALUS SAUNAS 3 and 6 Person Steam Saunas Owner’s Manual

FOR STEAM MODEL SAUNAS
REQUIRES 220VAC /1PHASE
(30/40AMP, depending on your electrical code)
DEDICATED CIRCUIT FOR THE STOVE
REQUIRES 120VAC 15 AMP CIRCUIT FOR THE SAUNA
Heavenly, Fierce and Charisma
2, 3 and 6 Person Steam Saunas
OWNER’S MANUAL
The stove must be installed by a certified electrician per
the manufacturer’s manual.
The stove must be installed per the electrical code in
your area with reference to the breaker and wire sizes.
Model and parts are subject to change.
the unit from the power source.
9. Allow 30 seconds between turning the control system “On” and “Off”. By allowing 30
seconds between powering the control system “On” and “Off” will prolong the life of
the unit.
10. Confirm that you adhere to the correct power requirements of the control system.
Connecting the control system to other than the required voltage can damage the
control system and possibly cause serious injury. It is very important that the load
parameters are consistent with that needed by the control system.
11. Canadian Red Cedar and its rich aroma can cause an extremely small percentage of
the population to have an adverse reaction known as Multiple Chemical Sensitivity
(MCS). While this is not a universally recognized disorder in the medical field, certain
consumers have an adverse physical reaction to low levels of many common
chemicals and cannot tolerate any aromatic oils, shampoos with perfumes infused or
certain herbs with natural aromas. However, for the majority of the population,
Canadian Red Cedar is the sauna wood of choice.
3
CAUTION: Exit sauna immediately if you feel dizzy, sleepy, or
any discomfort.
READ ALL INSTRUCTIONS THOROUGHLY BEFORE ASSEMBLY
Heavenly
*The above assembly diagram i s for quick reference only. Read all
instructions before assembling. All sauna models may not be shown.
Parts and accessories may vary.
4
Schematics
Heavenly
*The above assembly diagram i s for quick reference only. Read all
instructions before assembling. All sauna models may not be shown.
Parts and accessories may vary.
5
CAUTION: Exit sauna immediately if you feel dizzy,
sleepy, or any discomfort.
READ ALL INSTRUCTIONS THOROUGHLY BEFORE ASSEMBLY
Fierce
*The above assembly diagram i s for quick reference only. Read all
instructions before assembling. All sauna models may not be shown.
Parts and accessories may vary.
6
Schematics
Fierce
*The above assembly diagram i s for quick reference only. Read all
instructions before assembling. All sauna models may not be shown.
Parts and accessories may vary.
7
CAUTION: Exit sauna immediately if you feel dizzy,
sleepy, or any discomfort.
READ ALL INSTRUCTIONS THOROUGHLY BEFORE ASSEMBLY
Charisma
*The above assembly diagram i s for quick reference only. Read all
instructions before assembling. All sauna models may not be shown.
Parts and accessories may vary.
8
Schematics
Charisma
*The above assembly diagram i s for quick reference only. Read all
instructions before assembling. All sauna models may not be shown.
Parts and accessories may vary.
9
TABLE OF CONTENTS
Product Introduction
Wall Panel Descriptions
Assembly Instructions
Control Panel Operation
Tips for Using Your Sauna
Safety Instructions
Safeguards for Your Sauna
Warranty
Warranty Card
10
10
14
22
24
25
26
27
29
WARNING: Visually inspect all parts before assembly to make sure they are not
damaged. Any excessive vibrations during transport could cause damage to the
sauna components. DO NOT START the sauna if damage is detected! Contact
your dealer or manufacturer for troubleshooting and replacement parts.
PLEASE NOTE: The pictures and diagrams shown within this owner’s manual are
representations of this model. Actual model may vary. Design and construction
are subject to change. The sauna cannot be placed directly in the weather
elements. It is highly recommended to keep the weather elements from reaching
the sauna by placing the sauna under a covered patio or structure with a roof to
fully protect the sauna.
1. Product Introduction
The steam sauna room is composed of a wood cabin. The wood cabin includes a
FRONT WALL PANEL with GLASS, REAR WALL PANEL, LEFT SIDE WALL PANEL,
RIGHT SIDE WALL PANEL with Glass, FLOOR PANEL, ROOF, and BENCHE(S).
Other smaller wood items will also be included and can be identified in the schematics
on pages 4, 6, and 8.
2. Wall Panel Descriptions
A. The REAR WALL PANEL can be seen in the image below. It will have
the control panel for the radio and lights on the interior. It will also have
the vent to the right of the control panel. (see Figure 1)
10
Control Panel for Radio & Lights
Vent
Figure 1
B. The LEFT SIDE WALL PANEL will have a vent near the bottom of the
wall for the stove ventilation. The RIGHT SIDE WALL PANEL will have
a stationary glass panel. The FRONT WALL PANEL will have the
GLASS DOOR. (see Figure 2)
Vent
Front Glass Door
Stationary Glass Panel
Vent
Speaker
Figure 2
NOTE: The pictures and diagrams shown above/below are for representational
purposes only. Actual model may vary. Parts subject to change.
11
Highlights
I.
Buckles
A.
External Buckles
The external buckles are used to connect the LEFT and RIGHT SIDE
PANELS to the REAR PANEL. (see Figure 3)
Figure 3
B.
Guide and Guide Inserts
The guide and guide inserts are used to connect the FRONT PANEL
to the RIGHT SIDE PANEL and the LEFT SIDE PANEL. (see Figure
4)
Figure 4
II.
Panel Descriptions
For easier assembly, please understand and distinguish the differences between
each panel.
A.
Floor Panel
The floor panel will be a lattice piece of wood and it will not cover the
entire floor (does not cover under the bench). (see Figure 5)
12
FLOOR PANEL
Figure 5
B.
Understanding the Difference Between the Top and Bottom of
the Wall Panels
The (4) Wall Panels will have white plastic feet on the bottom of the
wall panels. (see Figure 6)
Plastic Feet are on the Underside
of the Wall Panels
Figure 6
13
Assembly Instructions
A. Choose a good location to install the sauna
1. The location must be dry, leveled, and away from any source of water.
2. The stove must be installed by a certified electrician.
3. Wood cabin installation order: FRONT WALL PANEL
LEFT SIDE WALL
PANEL
RIGHT SIDE WALL PANEL
FLOOR PANEL
REAR
WALL PANEL BENCH SUPPORT PANELS BENCH BACK
BACKREST ROOF PANEL
4.
Tools Required: Battery Operated Screwdriver or Hand-Held Philips
Screwdriver, Rubber Mallet, and Ladder.
B. Installing the FRONT WALL PANEL and LEFT SIDE WALL PANEL
1. Place the FRONT WALL PANEL upright and in the desired location.
Next, stand the LEFT SIDE WALL PANEL upright and next to the FRONT
WALL PANEL. Align the metal Guide Insert Brackets on the LEFT SIDE
WALL PANEL and the FRONT WALL PANEL. Now you will need to lift
the LEFT SIDE WALL PANEL up and onto the FRONT WALL PANEL
locking the metal Guide Insert Brackets into one another. (see Figure 7)
Figure 7
14
C. Installing the RIGHT SIDE WALL PANEL, FLOOR PANEL and
REAR WALL PANEL
1. Place the RIGHT SIDE WALL PANEL upright and next to the
FRONT WALL PANEL. Align the metal Guide Insert Brackets on the
RIGHT SIDE WALL PANEL and the FRONT WALL PANEL. Now
you will need to lift the RIGHT SIDE WALL PANEL up and onto the
FRONT WALL PANEL locking the metal Guide Insert Brackets into
one another. Next, place the FLOOR PANEL on the floor and next
to the FRONT WALL PANEL. The REAR WALL PANEL can now be
placed up against the RIGHT SIDE WALL PANEL and LEFT SIDE
WALL PANEL. You will use the buckles to latch the REAR WALL
PANEL to both the RIGHT SIDE WALL PANEL and LEFT SIDE
WALL PANEL. (see Figure 8)
Figure 8
D. Installing the SIDE BENCH SUPPORT PANEL, BENCH SUPPORT
PANEL, BENCH, and BACKREST
1. First, you will need to locate the SIDE BENCH SUPPORTS. See
Figure 9. The SIDE BENCH SUPPORTS will be the same for sauna
models Heavenly and Fierce. The SIDE BENCH SUPPORT
for sauna model Charisma will be different. The SIDE BENCH
SUPPORT will need to be screwed to the RIGHT SIDE WALL
PANEL using the 1 7/8” screws. The SIDE BENCH SUPPORT will
have predrilled holes.
15
SIDE BENCH SUPPORTS
For HEAVENLY
&
FIERCE
BENCH SUPPORT PANEL will
slide within the vertical slot on
the SIDE BENCH SUPPORTS
For CHARISMA
Figure 9
2. It is time to locate the BENCH SUPPORT PANEL. Depending on
your sauna model will determine how many BENCH SUPPORT
PANELS you have. For sauna models Heavenly and
Fierce, you will have only one BENCH SUPPORT PANEL.
For sauna model Charisma, you will have two BENCH
SUPPORT PANELS. The BENCH SUPPORT PANEL will side
downward within the vertical slots on both the LEFT SIDE WALL
PANEL and the SIDE BENCH SUPPORT PANEL(S) (see Figure 10)
16
HEAVENLY
&
FIERCE
BENCH SUPPORT PANELS
CHARISMA
Figure 10
3. See Figure 10 and locate the BACKREST. You will need to screw
the BACKREST to the wood plank on the REAR WALL PANEL.
(see Figure 11)
Wood Plank on REAR WALL PANEL
Installing BACKREST
Figure 11
17
Predrilled
screw holes
I. Installing the GLASS DOOR HANDLE and ROOF PANEL
1. Locate the GLASS DOOR HANDLE. The GLASS DOOR will
need to sit between the plastic washer (on the outside) and the
wood handle (on the inside). (see Figure 12)
2. Place the ROOF PANEL over the wall panels carefully. Be
cautious when feeding the wires for the lights from the
REAR WALL PANEL to the top of the ROOF PANEL. (see
Figure 13)
3. Next, carefully slide the ROOF PANEL into place. You will need
to connect the wire connections for the lights up on the rooftop.
4. It is optional to use the 1 7/8” screws to screw the roof panel to
the side wall panels.
Exterior Side:
(metal handle + Metal Ring
+ Plastic Washer)
Interior Side:
(wood handle)
Figure 12
Figure 13
Note: Be sure to remove the black plastic protection corners from around the glass
door corners, if present.
18
J. Installing the Stove
Please Note: The stove must be installed by a certified electrician per the manufacturer’s
manual. The stove must be installed per the electrical code in your area with reference
to the breaker and wire sizes & wire material. Be sure to follow the manufacturer’s
manual for proper and safe installation of the stove. For the Harvia The Wall Heater, it is
very important to run the stove power cord through the vent hole in the wall panel and
close the vent before installing the stove as you will not be able to open the vent once
the stove is installed. See Figure 14. After the stove is mounted, you can install the
wood housing for the stove. The wood housing does vary in styles.
Vent Hole
Figure 14
1. First, you will need to locate the wood housing for the stove and assemble it using
the provided screws. (see Figure 15)
Figure 15
19
2. Next, you will need to mount the wood housing to the sauna wall panel using the
provided screws. You will install the wood housing around the stove as the
stove does get very hot. (see Figure 15)
Figure 15
ASSEMBLY COMPLETED!
20
SAUNA CONTROL PANEL - GENERAL INTRODUCTION
1. Description of Functions
Functions
Touch Key technology
FM Radio
Reading Lamp
Background Lamp and Star Lights
Bluetooth Music Play
2. Control System Specifications
A.) Rated Voltage: AC100V-AC240V
B.) Bluetooth Approximate Effective Distance: 33 feet
C.) Rated Power: 50Hz/60Hz
3. LCD Screen displays the following information:
4. Devices controlled by the Control System are:
A.) Reading Lamp
B.) Background Lamp and Star Lights
C.) Speaker System
21
√
√
√
√
√
5. Control Panel Display
CONTROL PANEL OPERATION
1. “
“: Powers the unit “ON/OFF”.
A.) Press the “
“ to turn the Control Panel “ON”. The LED will display “
“,
which means the Control System has powered “ON”. In addition, the Reading Lamp
should be “ON” as well. If you press the “
“ once again, the Control Panel
will turn “OFF”.
B.) The Control System will remain “ON” for 45 minutes. After the 45 minutes has
expired, the Control System will turn “OFF”.
2. “
“: Powers the Reading Lamp “ON/OFF”.
A.) Press the “
Press the “
“ to turn the Reading Lamp “ON”. The LED will show “
“ again to turn the Reading Lamp “OFF” and the “
disappear.
3. “
“: Powers the Background Lamp and Star Lights “ON/OFF”.
22
“.
“ will
A.) Press the “
“ to turn on the Background Lamp and Star Lights. The LED
will show “
“. Press the “
Star Lights “OFF” and the “
4. “
“ again to turn the Background Lamp and
“ will disappear.
“: Powers on the Radio and operates the Bluetooth (
A.) Press the “
).
“ to turn “ON” the FM function of the Radio. The LCD display will
show the current frequency. When you press the “
“ again, you will turn on
the Bluetooth function allowing you to connect your musical device. Once the
Bluetooth is connected to your musical device, the “
flashing. If the “
“ and “
“ and “
“ will stop
“ continue to flash, then your musical device has
not connected to the Bluetooth.
B.) To exit from “
“, press “
C.) If you have exited from “
“ a third time.
“, you will need to press the “
“ to
return to the FM function. The FM frequency range is 87.5MHz – 108.0MHz. You can
select a FM radio station by pressing “
or “
“ and “
“. If you press either “
“
“ for more than 2 seconds, the system will search for radio stations. You will
see the selected radio station on the Control Panel display. If you scroll to the
frequency range limit (say 108.0MHz), press the “
“ again and it will continue to
87.5MHz.
D.) To set the radio station, press the “
“ until you see “
Control Panel display. While it is flashing, press the “
station you want memorized. Then press “
“ flashing on the
“ and “
“ to select the
“ and hold for 3 seconds to store it.
Once stored, you can search the memory to find that stored station. When you are still
in the FM function, press “
press “
“ or “
“ until the Control Panel displays “
“. Then
“ to select a stored station. To exit, press “
E.) To sink with Bluetooth, search the Bluetooth device name “JOYONWAY”. The
password will be “2288” and you should now be able to pair with the device.
23
“.
Once the Bluetooth is connected to your musical device, the “
stop flashing. If the “
“ and “
“ and “
“ will
“ continue to flash, then your musical device
has not connected to the Bluetooth. To disconnect your device from the Bluetooth,
turn off your device and press “
“ for 3 seconds.
F.) To pause the music while your musical device is playing, press “
“ for 3
seconds. Do the same to stop the pause and continue playing music. To play the
previous song or next song, you can press “
“ or “
“.
G.) The volume adjusting range is from -80dB to 0dB. To adjust the volume, press
“
“ until “
“ blinks on the Control Panel display. You can in press the
“
“ and “
“ to adjust the volume setting. If you hold the “
“ and
“
“ for more than 2 seconds, the volume will increase/decrease at a faster pace.
After 5 seconds, the volume setting will be stored and the function will cancel itself.
Tips for using Your Sauna
1) If you take a hot/warm shower or bath before using your sauna, you may perspire more and
experience more comfort.
2) Drink water prior to, during, and after your sauna session to replenish body fluids.
3) To regulate the set temperature inside the sauna to your comfort level, use the movable
ventilation or leave the door open slightly. The ventilation is installed on the sauna and used
based on personal preference.
4) Use 2 or 3 towels during your sauna session. Fold one of the towels several times and place it on the
bench. This towel will absorb some of your perspiration while adding comfort as you sit on the
bench. Place another towel on the floor to absorb perspiration as it falls from your body. Use a third
towel to wipe perspiration from your body from time to time.
5) At the first sign of a cold or flu, increasing your sauna sessions may be beneficial in boosting
your immune system and decreasing the reproductive rate of viruses.
6) To help relieve sore and tense muscles, massage the affected areas during your sauna session.
7) To treat your ankles and feet more effectively, you can elevate them and move them close to one
of the heat emitters to achieve a deep heating effect.
8) The peaceful and relaxed state rendered by a sauna session may help you to sleep easier and
deeper.
9) To protect the life of the stove, you can plug the unit into a GFCI outlet or unplug it when not in use.
24
10) After the sauna session is over, do not jump into the shower or bath immediately. Because your
body was heated up during the sauna session, it will continue to perspire even after you exit the
sauna room. Sit in the sauna with the door open slightly and let your body cool down. Once your
body has cooled down and you feel comfortable, you can exit the sauna. After about twenty
minutes and when your body has completely cooled down, you can take a shower to rinse the
perspiration off your body.
Safety Instructions
1.) Read and follow all instructions carefully before using the sauna.
2.) When installing and using the electrical equipment, safety precautions should always be followed.
3.) To reduce the risk of injury, do not allow children to use the sauna unless they are directed by a
medical doctor and are closely supervised at all times by an adult.
4.) Do not use the sauna immediately following strenuous exercises. Wait at least 30 minutes to
allow the body to cool down completely.
5.) Pregnant or possibly pregnant women should contact their physician prior to using the sauna.
Excessive temperature has a high potential for causing fetal damage during pregnancy.
6.) Hyperthermia Danger: the normal body temperature can't rise above 39°C (103°F). Symptoms of
excessive hyperthermia include dizziness, lethargy, drowsiness, and fainting. The effects of excessive
hyperthermia may include failure to perceive heat, physical inability to exit sauna, unawareness of
impending hazard, unconsciousness and fetal damage in pregnant women. Hyperthermia could
make your body's core temperature rise. Setting desired temperature to an excessively high
temperature is not recommended.
7.) The use of alcohol, drugs, or medications prior to or during the sauna session may lead to
unconsciousness and/or other harmful physical
injuries .
8.) Persons suffering from obesity or with a medical history of heart disease, low or high
blood pressure, circulatory system problems, or diabetes should consult a physician prior
to using the sauna.
9.) Persons using medications should consult a physician before using the sauna. Some medications
may induce drowsiness while others may affect the heart rate, blood pressure, and/or blood
circulation.
10) Exercise care before and after sauna use.
11) Never sleep inside the sauna.
12) Do not use any type of cleaning agents on the interior of the sauna. Only wipe down with a
cloth and water.
13) Do not stack or store any object on top or inside the sauna.
14) If the power supply cord becomes damaged, it must be replaced immediately by the manufacturer
or its agent. If you find the power cord is too hot or that the electrical equipment may be
experiencing technical problems, please contact the manufacturer or its agent immediately to
avoid hazardous conditions.
15) Do not use the sauna during an electrical storm to avoid risk of shock.
25
16) Do not touch the glass door hinges during sauna use as they become very hot to the touch.
17) Your hands must be dry and free of moisture before plugging and unplugging cords and wiring
harnesses from the power supply and circuit boards. Never operate the sauna with wet hands or
wet feet to avoid risk of electric shock. Never touch the metal prongs of the plug.
18) Do not attempt to make any repairs yourself without contacting the manufacturer first. If a
problem occurs with the sauna, please contact seller, distributor, or the manufacturer to avoid
safety risks. Unauthorized repair attempts will void the manufacturer’s warranty.
19) Please make sure the outlet power supply meets the specifications required. Failure to meet
the requirements may cause safety risks.
20) Some sauna models are equipped with reading and roof lamps. Because the lamp temperature
will become very hot once powered on, do not attempt to touch the lamp to avoid being
burned. Do not attempt to touch it for at least 20 minutes after it has been powered off.
21) Do not bump, hit, or break the stove as it may cause an electrical short and pose a
safety risk.
22) Do not make any modifications to the sauna, the sauna structure, or the sauna components.
23) Prior to each sauna session, the sauna room is to be inspected for correct operation. If for any
reason your sauna room does not seem to be operating properly, discontinue use and contact the
manufacturer.
Safeguards For Your Sauna
1. Do not install the sauna near water, near a bathtub, near a shower, in a wet basement, or near a
swimming pool.
2. Do not use liquid cleaners or aerosol cleansers inside the sauna. Unplug the sauna from the wall
outlet before cleaning. Use plain water and a soft cloth for cleaning.
3. The power supply cord should be routed so that it is not walked on or pinched by any object that
may be placed against it.
4. When replacement parts are required, be sure they meet the specified requirements of the
manufacturer.
Unauthorized substitutes may result in fire, electric shock, or other hazardous conditions. After any
repairs, please ask the service technician to perform safety checks to determine that your sauna is
working properly.
5. Do not use any wall receptacle adapter or extension cord between the sauna cord and wall
receptacle.
Limited Lifetime Warranty
26
*Limited Lifetime Warranty: Golden Designs, Inc. warranties the sauna room and its attached electronics
against defects in material and workmanship for the life of the product from the original date of purchase.
This sauna is for indoor use or outdoor use when protected from the outdoor weather elements by a
structure that includes a water-proof roof. When not in use and placed outdoors, a water proof cover
must be used to cover the sauna room or the warranty will become void. Any damage due to direct
exposure to outdoor weather elements such as rain, snow, sun, wind or extreme temperatures will not
be covered by this warranty. Any damages as a result of modifications made to the sauna or its
components will void this warranty.
Extent of Warranty: This limited warranty applies to products manufactured or distributed by Golden
Designs, Inc. under the Golden Designs Inc. brand name, delivered in the continental United States or
Canada and extends to the original purchaser at the original site of installation only. This warranty
becomes valid at time of purchase and terminates either by specified time frame, owner transfer, or
relocation. The warranty extends to the sauna room and excludes the stove as it is covered by its own
manufacturer warranty. Your sales receipt showing the date of purchase of the product is your proof of
purchase.
Manufacturer Warranty
All Golden Designs, Inc. products are manufactured with the highest quality appliances and are warranted
to be free from defects in material and workmanship at the time of delivery. The appliance warranty is
extended through the manufacturer for the product including, but not limited to: sauna control panel and
connected wire harnesses. All exchanged parts and products replaced under this warranty will become
the property of Golden Designs, Inc. Golden Designs, Inc. reserves the right to change for any part not
covered under the existing warranty. Any parts determined to be defective must be returned to Golden
Designs, Inc. at its discretion to obtain warranty service. You must prepay any shipping charges, export
taxes, custom duties and taxes, or any other charges associated with the transportation of the parts. In
addition you are responsible for insuring any parts shipped or returned. You must present Golden
Designs, Inc. with proof of purchase documents (including the date of purchase). Any evidence of
alteration, erasing or forgery of proof of purchase documents will be cause to VOID this limited warranty.
Products on which the serial number has been defaced or removed is not eligible for warranty service.
Warranty Limitations
This warranty does not apply if the unit has been subject to full commercial use, negligence, alteration,
modification, misuse, abuse, repairs by non-Golden Designs, Inc. authorized personnel, inappropriate
installations, or any case beyond the control of Golden Designs, Inc. invalidating this warranty including
but are not limited to:





Use of lacquer or paints
Sauna and other Golden Designs, Inc. products accessories placed on non-approved surfaces
Outdoor applications when not protected from outdoor weather elements
Normal wear and tear or weathering
Use of product not in accordance with instructions
Surface cracks are not considered defects in material or workmanship, as they are normal
characteristics of all woods. This includes minor cracks due to wood expansion and contraction. Note:
Since the wood used in construction has been kiln dried, a certain amount of expansion and contraction
occurs in the wood in a sauna environment.
27
Disclaimers
Golden Designs, Inc. shall not be liable for loss of use of sauna or other Golden Designs, Inc. products or
other secondary or incidental or consequential costs, expense or damages - which may include the
removal of permanent structures or other custom fixtures or the necessity for crane removal - arising
directly or indirectly out of the use or inability to use the product. Any implied warranty shall have
duration equal of the applicable warranty stated above. Under no circumstances shall Golden Designs,
Inc. or any of its representatives be held liable for injury to any person or damage to any property,
however arising. Specifications are subject to change without notice or obligation.
Legal Remedies
This limited warranty gives you specific legal rights. You may have other rights, which may vary from state
to state.
Customer Service
For customer service, contact your authorized dealer. If you need additional information or assistance,
please email Golden Designs, Inc. at [email protected] or call (909) 212-5555.
*Limited Lifetime Warranty of Sauna Products is 7 years on wood structure, control panel, and applicable
control panel harnesses and lights from the date of purchase. Stove/heater is covered under its
manufacturer’s applicable warranty.
28
WARRANTY CARD
Congratulations on your purchase of an Infrared Sauna from Golden Designs, Inc. Please take the time to
complete the following Warranty Card and mail it back to:
Golden Designs, Inc.
3550 Jurupa Street, Unit B
Ontario, CA 91761
Please include a copy of your sales receipt showing date of purchase as this will serve as proof of
purchase.
**Serial number (S/N) is located on the sauna’s front panel, rear panel, or on the carton.**
DETACH HERE
WARRANTY CARD
All fields must be completed to validate the warranty.
Name:
Address:
City:
State:
Zip Code:
Phone Number:
Purchase Date:
Product Name:
Purchase From:
Serial Number:
29
">