Liebherr XRFsf 5240 Plus Side-by-Side combination Assembly and installation instructions
PDF
Download
Document
Advertisement
Advertisement
Installation Guide Quality, Design and Innovation home.liebherr.com/fridge-manuals General safety instructions Contents 1 General safety instructions.................................. 2 2 Installation dimensions........................................ 3 3 Transporting appliance......................................... 4 4 Unpacking the appliance...................................... 4 5 Disposing of packaging......................................... 4 6 Side by side assembly........................................... 4 The manufacturer is continually working on the further development of all types and models. Please be aware that we reserve the right to make changes to the shape, equip‐ ment and technology. Symbol Explanation Read instructions Please read the information in these instruc‐ tions carefully to understand all of the benefits of your new appliance. Full instructions on the internet You can find detailed instructions on the internet using the QR code on the front of these instruction or by entering the service number at home.liebherr.com/fridgemanuals. The service number can be found on the serial tag: correct use of the appliance. Follow the instructions, safety instructions and warning messages included at all times. They are important for ensuring you can operate and install the appliance safely and without any problems. - First read the general safety instructions in the “General safety instructions” section of the operating instructions, which accom‐ pany these installation instructions, and follow them. If you cannot find the operating instructions, you can down‐ load the operating instructions from the internet by entering the service number at home.liebherr.com/fridge-manuals. The service number can be found on the serial tag: - Observe the warning messages and other detailed information in the other sections when installing the appliance: DANGER identifies a situation involving direct danger which, if not obvi‐ ated, may result in death or severe bodily injury. WARNING identifies a dangerous situation which, if not obviated, may result in death or severe bodily injury. CAUTION identifies a dangerous situation which, if not obviated, may result in minor or medium bodily injury. NOTICE identifies a dangerous situation which, if not obviated, may result in damage to property. Note identifies useful instructions and tips. Fig. Example illustration Check appliance Check all parts for transport damage. If you have any complaints, please contact your agent or customer service. Differences These instructions apply to a range of models, so differences are possible. Sections that apply to certain models only are marked with an asterisk (*). Instructions and results Instructions are marked with a Results are marked with a . . Videos Videos about the appliances are available on the YouTube channels of Liebherr-Hausgeräte. 1 General safety instructions - Please keep this assembly manual in a safe place so you can refer back to it at any time. - If you pass the appliance on, please hand this assembly manual to the next user. - Read this assembly manual carefully before installation and use to ensure safe and 2 * Depending on model and options Installation dimensions 2 Installation dimensions Fig. 2 Example illustration Fig. 1 Example illustration Fig. 3 Example illustration For appliances with a lever handle a b c d e f h g S(BN)(CN)(FN)(sd)(st)(bd)(bs) 52..(i) 1204 mm 1855 mm 611 mmx 675 mmx 1222 mmx 1318 mm 35 mm 90° * Depending on model and options 3 Transporting appliance a CBN.. 76.. b c d e f h g 1504 mm 1855 mm 611 mmx 675 mmx 1365 mmx 1618 mm 35 mm 90° For appliances with a lever handle For appliances with recessed grip x The use of wall spacers increases the dimensions by 15 mm . The dimensions with an open door apply for an opening angle of 90°. The clearances vary depending on the opening angle. a b c d e f h g SFN(sd)(sf)(bd) 52.. 1226 mm 1855 mm 611 mmx 675 mmx 1217 mmx 1252 mm 35 mm 90° For appliances with a recessed grip x The use of wall spacers increases the dimensions by 15 mm . The dimensions with an open door apply for an opening angle of 90°. The clearances vary depending on the opening angle. 3 Transporting appliance Note when transporting the appliance: u Transport the appliance upright. u Use two people to transport the appliance. During first use: u Transport the appliance packaged. When transporting appliances after initial commissioning (e. g. moving or cleaning): u Empty the appliance. u Secure the door against unintentional opening. 6 Side by side assembly Set up the freezer or the appliance with the freezer compartment from the left when viewed from the front. These appliances are equipped with a side-wall heater on the right hand side to prevent condensation forming. All the assembly components are supplied with the appli‐ ance. Assembly parts in the accessory kit For appliances with lever handle 4 Unpacking the appliance Before you connect the appliance, report any damage imme‐ diately to the delivery company. u Check the appliance and the packaging for damage during transport. Contact the supplier immediately if you suspect any level of damage. u Remove all materials from the back or the side walls of the appliance that may prevent proper installation or ventilation. u Remove all protective films from the appliance. Do not use sharp or pointed objects for this. u Take the power cable from the rear of the appliance. Remove the cable brackets when you do this, otherwise there will be noise caused by vibrations! Fig. 4 For appliances with recessed grip 5 Disposing of packaging WARNING Danger of suffocation due to packing material and plastic film! u Do not allow children to play with packing material. The packaging is made of recyclable materials: - corrugated board/cardboard - expanded polystyrene parts - polythene bags and sheets - polypropylene straps - nailed wooden frame with polyethylene panel* u Take the packaging material to an official collecting point. 4 Fig. 5 For all appliances Fig. 6 For appliances with bottom soft stop mechanism* Base trims* * Depending on model and options Side by side assembly u Take off all protective film from the exterior of the appli‐ ance. Bottom front of the appliance: Fig. 7 * Swap bearing block cover Fig. 8 For appliances without bottom soft stop mechanism* Base trims* Fig. 9 * Tool for assembly Fig. 10 Fig. 11 u Tighten the outer adjusting feet. The appliances can be moved easier. For appliances with lever handle u Push both appliances so that they are approx. 10 mm apart from each other, and they are positioned flush facing forwards. For appliances with recessed grip u Push both appliances so that they are approx. 32 mm apart from each other, and they are positioned flush facing forwards. u Straighten the appliances up using a spirit level on the top of the appliance. Top front of the appliance: Ensure that the following tools are to hand: q Size 10 open-ended spanner (supplied) q Torx® 25/20/15 screwdriver q Cordless screwdriver q Spirit level Information on moving the SBS combination: q Set up the appliances as close to the final position as possible before assembly. The appliances must be accessible on all sides for correct assembly. q When moving the appliances after assembly, always take hold from the front outer corners. Never press your knee against the side walls or door. q The SBS combination can be moved most easily when moved diagonally, that is by alternately pushing from the left and right corners. If the combination is standing directly in front of the recess, push it in straight. Fig. 12 u Remove the existing covers. u Before fitting the top bracket remove both earthing screws Fig. 12 (14). u Store the earthing screws safely. The screws will be necessary for fitting the bracket as shown below. q If the combination has to be pulled out of the recess again, take hold of the bottom third of the combi‐ nation and pull forward straight. NOTICE Risk of damage when moving the combined SBS appliance! The combined SBS appliance is heavy once assembled. The appliance may be dented by improper movement. u Observe the information given on moving the appliance (see above). * Depending on model and options Fig. 13 Example illustration u Slide the bracket Fig. 13 (3) onto the pins with the spacer between the appliances. Loosely screw in the brackets alternately right and left with four screws Fig. 13 (4) and the previously removed earthing screws Fig. 13 (14). u If necessary: Check the appliance is stood straight by laying a spirit level on the top of the appliance. 5 Side by side assembly Bottom front of the appliance: u Remove the existing covers. Fig. 14 u If the metal plate Fig. 14 (1) is installed, unscrew the metal plate. Note If you want to transport the appliance or set it up as an individual appliance, you must re-attach the metal plate. Fig. 17 Example illustration u Slide the bracket Fig. 17 (8) on with the slots over the retainer for the wall spacers. Note Holes for the screws must be pre-drilled. u Mark the position of the holes to be drilled with a pencil. u Remove the bracket again. Note Only drill through the metal plate. Drill depth approx. 1 mm. Fig. 15 Example illustration u Slide the bracket Fig. 15 (6) on with the spacer between the appliances and screw in loosely with the 4 screws Fig. 15 (4). u If necessary: Set up the appliances so that they are level. u Tighten the screws firmly at the top and bottom. Top rear of the appliance: Fig. 18 u Pre-drill the screw holes with a 3 mm bit and deburr. Fig. 16 Example illustration u Slide the bracket Fig. 16 (7) onto the appliance ceiling with the lugs and with the spacer between the appli‐ ances. Screw in firmly with 2 screws Fig. 16 (5). Bottom rear of the appliance: 6 * Depending on model and options Side by side assembly Fig. 22 u On the front, press the long cover strip Fig. 22 (10) into the vertical gap. Ensure that the strip rests on the connecting plate. For appliances with recessed grip Fig. 19 Example illustration u Slide the bracket Fig. 19 (8) on once more with the slots over the retainer for the wall spacers. u Screw in tightly with the 2 screws Fig. 19 (5). Before fitting the top and front cover strips, push the two bars together over the whole length. The strips can be inserted more easily into the gap. Use a soft cloth to push the strips in to avoid dents in the surface of the cover strips. Press the strips into the gap carefully and evenly in order to achieve an optimum bond. For appliances with lever handle Fig. 23 u On the front, press the long cover strip Fig. 23 (10) into the vertical gap. Ensure that the strip rests on the connecting plate. u Take off the protective film from the cover strip.* Top front of the appliance: Fig. 20 u On the top press the short cover strip Fig. 20 (9) into the horizontal gap. For appliances with recessed grip Fig. 24 Example illustration u Snap the top cover Fig. 24 (11) onto the still open gap between the two control panel trims. Make sure that the outer sides of the cover form a flush finish with the control panel trims. Bottom front of the appliance Fig. 21 u On the top press the short cover strip Fig. 21 (9) into the horizontal gap. For appliances with lever handle Fig. 25 Example illustration * Depending on model and options 7 Side by side assembly u Place the bottom cover Fig. 25 (12) onto the bracket from the front Fig. 25 (1), slide it down Fig. 25 (2) and snap it in at the bottom Fig. 25 (3). u To disassemble the cover, insert a screwdriver at the bottom on the side below the cover and release both lower hooks. The cover can swing out upwards. u Connect the combination electrically. See the installation guide. Appliances with IceMaker or InfinitySpring: u Connect the appliance to the fixed water connection. See the installation guide. Note The base trim must be pushed to a little behind the bearing bracket cover.* For appliances without bottom soft stop mechanism* NOTICE Risk of damage when moving the combined SBS appliance! The combined SBS appliance is heavy once assembled. The appliance may be dented by improper movement. u Observe the information given on moving the appliance (see above). u Carefully push the SBS combination into the specified position. u If necessary, align the SBS combination using the level‐ ling feet. u Then prop up the door: Lower outer adjusting feet on the bearing bracket until they are resting on the floor. The doors can be straightened at height on the outer lower bearing brackets: u Open the door to 90°. Fig. 28 * u Secure the base trim recess at the bottom of the appli‐ ance, as shown in the figure.* Fig. 26 u To lift the door, unscrew the adjusting foot Fig. 26 (18) clockwise using the supplied open-ended spanner Fig. 26 (2) until the foot makes contact with the floor. Then continue turning until the door is adjusted to the right height. When delivered, the bearing pin is completely screwed in. Fit decorative base trim.* After you have assembled and straightened out the appli‐ ances, the base trims can be fitted at the bottom of the appliances. The base trims are decorative and will not affect the functionality of the appliances.* For appliances with bottom soft stop mechanism* Fig. 27 * u Attach the base trim to the bottom of the appliance in the recess.* 8 * Depending on model and options Side by side assembly * Depending on model and options 9 home.liebherr.com/fridge-manuals Side-by-Side combinations Issue date: 20240216 Part number index: 7086153-00 Liebherr-Hausgeräte GmbH Memminger Straße 77-79 88416 Ochsenhausen Deutschland Installation Guide Quality, Design and Innovation home.liebherr.com/fridge-manuals General safety instructions Contents Symbol Explanation 1 General safety instructions.................................. 2 2 2.1 2.2 2.3 2.4 Installation conditions.......................................... Location......................................................................... Building the appliance into kitchen units................ Installing multiple appliances.................................... Mains connection......................................................... 3 3 3 4 4 3 Installation dimensions........................................ 5 4 Ventilation requirements...................................... 5 5 Transporting appliance......................................... 5 6 Unpacking the appliance...................................... 5 7 Mounting wall spacers.......................................... 5 8 Setting up the appliance....................................... 5 9 Setting up the appliance so that it is level........... 6 1 General safety instructions 10 After setting up..................................................... 6 11 Disposing of packaging......................................... 6 - Please keep this assembly manual in a safe 12 12.1 **** freezer compartment door*.......................... Moving the door hinge................................................ 6 6 13 13.1 13.2 13.3 13.4 13.5 13.6 13.7 13.8 13.9 Door hinge change................................................ Removing the door....................................................... Reversing the freezer compartment door*.............. Moving the upper bearing parts to the other side. Moving the lower bearing parts to the other side.. Moving the door bearing parts to the other side.... Moving the handles to the other side*..................... Fitting the door............................................................. Aligning the door.......................................................... Fitting the covers......................................................... 6 7 8 8 9 10 10 11 12 12 14 Connecting device................................................. 12 The manufacturer is continually working on the further development of all types and models. Please be aware that we reserve the right to make changes to the shape, equip‐ ment and technology. Symbol Explanation Read instructions Please read the information in these instruc‐ tions carefully to understand all of the benefits of your new appliance. Full instructions on the internet You can find detailed instructions on the internet using the QR code on the front of these instruction or by entering the service number at home.liebherr.com/fridgemanuals. The service number can be found on the serial tag: Differences These instructions apply to a range of models, so differences are possible. Sections that apply to certain models only are marked with an asterisk (*). Instructions and results Instructions are marked with a Results are marked with a . . Videos Videos about the appliances are available on the YouTube channels of Liebherr-Hausgeräte. place so you can refer back to it at any time. - If you pass the appliance on, please hand this assembly manual to the next user. - Read this assembly manual carefully before installation and use to ensure safe and correct use of the appliance. Follow the instructions, safety instructions and warning messages included at all times. They are important for ensuring you can operate and install the appliance safely and without any problems. - First read the general safety instructions in the “General safety instructions” section of the operating instructions, which accom‐ pany these installation instructions, and follow them. If you cannot find the operating instructions, you can down‐ load the operating instructions from the internet by entering the service number at home.liebherr.com/fridge-manuals. The service number can be found on the serial tag: - Observe the warning messages and other detailed information in the other sections when installing the appliance: Fig. Example illustration Check appliance Check all parts for transport damage. If you have any complaints, please contact your agent or customer service. 2 DANGER identifies a situation involving direct danger which, if not obvi‐ ated, may result in death or severe bodily injury. WARNING identifies a dangerous situation which, if not obviated, may result in death or severe bodily injury. * Depending on model and options Installation conditions CAUTION identifies a dangerous situation which, if not obviated, may result in minor or medium bodily injury. NOTICE identifies a dangerous situation which, if not obviated, may result in damage to property. Note identifies useful instructions and tips. 2 Installation conditions WARNING Fire hazard due to dampness! If live parts or the mains lead become damp this may cause short circuits. u The appliance is designed for use in enclosed areas. Do not operate the appliance outdoors or in areas where it is exposed to splash water or damp conditions. Intended use - Install and use the appliance in indoor spaces only. 2.1 Location WARNING Leaking coolant and oil! Fire. The coolant contained in the appliance is eco-friendly, but also flammable. The oil contained in the appliance is flammable. Escaping coolant and oil can ignite if the concentration is high enough and in contact with an external heat source. u Do not damage the pipelines of the coolant circuit and the compressor. Fig. 1 (1) Top cupboard* (2) Appliance* (3) Kitchen cabinet* (4) Wall* (B) Door depth* (C) Ventilation cross section* (D) Distance to the back of the appliance* (E) Distance to the side of the appliance* 2.1.2 Positioning (A) Appliance depth* You can place the appliance directly beside the kitchen cabinet Fig. 1 (3).* There must be a ventilation shaft at the depth Fig. 1 (D) of the back of the top cupboard over the entire width of the top cupboard.* The ventilation cross-section Fig. 1 (C) must be maintained under the ceiling.* If the appliance is set up with the hinges next to a wall Fig. 1 (4), the distance between the appliance and the wall must be at least 13 mm.* If the appliance is set up with the hinges next to a wall Fig. 1 (4), the distance between the appliance and the wall must be at least 20 mm.* In order to be able to fully open the door, the appliance must protrude by the depth of the door Fig. 1 (B) from the front of the kitchen cabinet. The appliance may protrude further depending on the depth of the kitchen cabinets Fig. 1 (3) and whether wall spacers are used.* - Do not install appliance in direct sunlight or next to an Appliances without handle / with recessed grip:* - If the appliance is installed in a very humid environment, condensation can build up on the outside of the unit. Always ensure good airlow and ventilation in the installa‐ tion location. - The more refrigerant there is in the appliance, the larger the space that it is installed in must be. If the space is too small, any leak may create a flammable mixture of gas and air. For every 8 g of refrigerant, the installation space must be at least 1 m3. Information regarding the coolant can be found on the serial tag inside the appli‐ ance. 2.1.1 Supporting floor - The floor of the installation site must be horizontal and even. - The surface supporting the appliance must be at the same level as the surrounding floor. oven, radiator or similar. - Install the appliance with the rear panel up against the wall and always use the supplied wall spacers (see below). 2.2 Building the appliance into kitchen units A 675 mmx B 75 mm C Min. 300 cm2 D Min. 50 mm E Min. 13 mm You can install kitchen cabinets around the appliance. * Depending on model and options 3 Installation conditions x The use of wall spacers increases the dimensions by 15 mm (see 7 Mounting wall spacers) .* Ensure that the following conditions are met: - Recess dimensions are adhered to . - Ventilation requirements are complied with (see 4 Venti‐ lation requirements) . 2.3 Installing multiple appliances NOTICE Risk of damage due to condensate! u Do not install the appliance directly alongside a further refrigerator/freezer. These appliances are designed for a variety of installation options. Combine appliances only if the appliance is suit‐ able. The following table shows the installation options by model: Fig. 2 (1) Top cabinet* (2) Appliance* (3) Kitchen cabinet* (4) Wall* (B) Door depth* (C) Ventilation cross section* (D) Distance to the back of the appliance* (E) Distance to the side of the appliance* (A) Appliance depth* You can place the appliance directly beside the kitchen cabinet Fig. 2 (3).* There must be a ventilation shaft at the depth Fig. 2 (D) of the back of the top cupboard over the entire width of the top cupboard.* The ventilation cross-section Fig. 2 (C) must be maintained under the ceiling.* If the appliance is set up with the hinges next to a wall Fig. 2 (4), the distance between the appliance and the wall must be at least 57 mm. This is how far the handle protrudes when the door is open.* In order to be able to fully open the door, the appliance must protrude by the depth of the door Fig. 2 (B) from the front of the kitchen cabinet. The appliance may protrude further depending on the depth of the kitchen cabinets Fig. 2 (3) and whether wall spacers are used.* Installation option Model Single All models Side-by-side (SBS) Model names starting with S.... Side-by-side All models without side wall heating with a space of 70 mm between the appliances Otherwise condensation will build up between the units. Fig. 3 Assemble the appliances together, following their specific installation instructions. 2.4 Mains connection WARNING Danger of fire due to incorrect positioning! If the mains cable or plug touches the back of the appli‐ ance, the vibration can damage the mains cable or the plug resulting in a short circuit. u Make sure the mains cable is not trapped under the appli‐ ance when you position the appliance. u Stand the appliance so that it is not touched by connec‐ tors or main cables. u Do not connect any appliances to sockets in the area of the back of the appliance. u Do not place and operate multi-sockets/power distribu‐ tors and other electronic devices (such as halogen trans‐ formers) at the back of the appliances. Appliances with lever handle:* A 675 mmx B 75 mm C Min. 300 cm2 D Min. 50 mm E Min. 57 mm x The use of wall spacers increases the dimensions by 15 mm (see 7 Mounting wall spacers) .* 4 * Depending on model and options Installation dimensions u When transporting after initial setup (e.g. relocation): Transport the appliance unloaded. u Transport the appliance upright. u Use two people to transport the appliance. 3 Installation dimensions 6 Unpacking the appliance Before you connect the appliance, report any damage imme‐ diately to the delivery company. u Check the appliance and the packaging for damage during transport. Contact the supplier immediately if you suspect any level of damage. u Remove all materials from the back or the side walls of the appliance that may prevent proper installation or ventilation. u Remove all protective films from the appliance. Do not use sharp or pointed objects for this. u Take the power cable from the rear of the appliance. Remove the cable brackets when you do this, otherwise there will be noise caused by vibrations! 7 Mounting wall spacers Fig. 4 h a b b' c c' d d' R.. 42.. 1255 597 675x — 609 — 1217x — R... 46.. 1455 597 675x — 609 — 1217x — Kf 46Z00 1455 597 675x — 609 — 1217x — R... 50.. 1655 597 675x — 609 — 1217x — R(B)... 52.. 1855 597 675x — 609 — 1217x — Ksfe 52Z20 1855 597 675x — 609 — 1217x — SR(B)... 5220 1855 597 675x — 609 — 1217x — SRsdh 5220 1855 597 675x 719x 609 654 1217x 1222 SR... 5230 1855 597 675x 719x 609 654 1215x 1222 RD... 52.. 1855 597 675x — 609 — With wall spacers, your device achieves the declared energy consumption and no condensation forms in high ambient humidity. The device is fully functional without the spacer brackets, but its energy consumption will be slightly higher. If you insert the wall spacers, then the device depth increases by approx. 15 mm. u Appliance with supplied wall spacers: Fit wall spacers on the rear of the appliance at the bottom left and right. 8 Setting up the appliance 1217x — x For appliances with supplied wall spacers, the dimensions must be increased by 15 mm (see 7 Mounting wall spacers) . 4 Ventilation requirements NOTICE CAUTION Risk of injury due to heavy appliance! u Have two people transport the appliance to its installa‐ tion site. WARNING Danger of overheating due to insufficient air ventilation! The compressor may be damaged if there is insufficient air ventilation. u Take care to ensure adequate air ventilation. u Observe the ventilation requirements. Danger of injury and damage due to the appliance being unstable! The appliance can topple over. u Secure the appliance as described in the instructions. If the appliance is integrated into a fitted kitchen, the following ventilation requirements must be adhered to: - There are spacer fins at the back of the appliance to provide sufficient ventilation. Make sure that these are not positioned in recesses or openings. - As a rule, the larger the ventilation space the more effi‐ ciently the appliance can run. Fire hazard and danger of damage! u Do not place appliances emitting heat e.g. microwaves, toasters etc. on the appliance! 5 Transporting appliance WARNING Ensure that the following conditions are met: q Only move the device when it is not loaded. q Only set up the appliance when someone is available to help. u On initial setup: Transport the appliance in its packaging. * Depending on model and options 5 Setting up the appliance so that it is level 9 Setting up the appliance so that it is level CAUTION Risk of injury or damage from the appliance tipping or the door falling open! If the additional adjustable foot on the base support is not correctly positioned on the floor, there is a risk of the door falling open or the appliance tipping. This can lead to injury or property damage. u Unscrew the additional adjustable foot on the support until it reaches the floor. u Then turn it another 90°. u Set up the appliance so that it is level using the supplied open-ended wrench to turn the adjustable feet (A) and a spirit level. u Then prop up the door: Turn the adjustable foot (B) on the bearing bracket until it comes into contact with the floor, then turn an additional 90°. u Then prop up the door: Turn the adjustable foot on the bearing bracket (B) using the open-ended wrench SW10 until it comes into contact with the floor, then turn an additional 90°. 12 **** freezer compartment door* It is very easy to reposition the hinge of the **** freezer compartment door if the main door hinge is swapped. If the main door of the appliance can be opened to more than 115° (1), you can open the freezer compartment without reposi‐ tioning the hinge. If the opening angle (2) of the appliance door is less than this, the hinge must be repositioned. Fig. 5 12.1 Moving the door hinge The slider for moving the door hinge is located on the back of the **** freezer compartment door at the bottom. 10 After setting up u Take off the protective film from the exterior of the appli‐ ance. u Take off the protective film from the trim panels. u Take off the protective film from the trim panels and drawer fronts. u Take off the protective film from the stainless steel rear panel. u Remove all transport safety components. u Clean the appliance. (see operating instructions) u Note the type (model, number), appliance designation, appliance/serial number, purchase date and dealer’s address. 11 Disposing of packaging Fig. 6 u Close the **** freezer compartment door (1). u Grab the **** freezer compartment door from below. u Move the slider (2) either to the right or to the left. 13 Door hinge change Tools WARNING Danger of suffocation due to packing material and plastic film! u Do not allow children to play with packing material. The packaging is made of recyclable materials: - corrugated board/cardboard - expanded polystyrene parts - polythene bags and sheets - polypropylene straps - nailed wooden frame with polyethylene panel* u Take the packaging material to an official collecting point. 6 Fig. 7 * Depending on model and options Door hinge change WARNING Danger of injury due to door falling out! If the bearing parts are not screwed on tightly enough, the door may fall out. This can result in serious injuries. In addition, the door may not close with the result that the appliance does not cool properly. u Screw on the bearing brackets/bearing pins tightly with 4 Nm. u Check all screws and retighten them if necessary. These sections apply for appliances without a soft stop mechanism: q For appliances without a soft stop mechanism q For all appliances NOTICE Risk of condensation damage for Side-by-Side appliances!* Certain appliances can be set up as Side-by-Side combina‐ tions (two appliances next to each other). If your appliance is a Side-by-Side (SBS) appliance: u Set up the SBS combination in accordance with the enclosed document. If the positioning of the devices is stipulated: u Do not change the door hinges over. Fig. 9 u Open the door. NOTICE Risk of damage! If the door seal is damaged, the door may fail to close prop‐ erly and the cooling will be inadequate. u Do not damage the door seal with the screwdriver! u Remove the outer cover. Fig. 9 (1) u Disengage and release the bearing bracket cover. Remove the bearing bracket cover. Fig. 9 (2) u Unlatch the panel with a slotted screwdriver and swivel it to one side. Fig. 9 (3) For all appliances: Fig. 8 Remember the reading direction. 13.1 Removing the door Note u Remove any food from the door racks before removing the door, so that no food falls out. For appliances without a soft stop: * Depending on model and options 7 Door hinge change 13.2 Reversing the freezer compartment door* Fig. 11 u For single-door appliances: Reverse the door hinge of the 4-star compartment by shifting the lever. The door of the 4-star compartment must be shut for this. Move the lever on the back of the door from below. 13.3 Moving the upper bearing parts to the other side For all appliances: Fig. 10 CAUTION Risk of injury if the door tips! u Take good hold of the door. u Set down the door carefully. u Carefully remove the protective cover. Fig. 10 (1) u Undo the bolt a little with a T15 screwdriver. Fig. 10 (2) u Hold the door and remove the bolts with your fingers. Fig. 10 (3) u Pull the bearing bush out of the guide. Insert from the other side and latch into place. Fig. 10 (4) u Lift the door and place it to one side. u Carefully lift the plugs out of the door bearing bush with a slotted screwdriver and pull them out. Fig. 10 (5) 8 Fig. 12 u Remove both screws with a T20 screwdriver. u Lift up and remove the bearing bracket. * Depending on model and options Door hinge change Fig. 14 u Lift the bearing pin completely upward and pull it out. Fig. 14 (1) u Take out the screws with a T20 screwdriver and take off the bearing bracket. Fig. 14 (2) For appliances without a soft stop: Fig. 13 u Take off the cover from above to the front. Fig. 13 (1) u Rotate the cover 180° and clip onto the other side from the right. Fig. 13 (2) u Latch the cover into place. Fig. 13 (3) u Position the upper bearing bracket. Fig. 13 (4) u Insert the screw with a T20 screwdriver and tighten it. Fig. 13 (5) u Insert the screw with a T20 screwdriver and tighten it. Fig. 13 (6) 13.4 Moving the lower bearing parts to the other side For all appliances: Fig. 15 u Loosen the screw using a T25 screwdriver. Fig. 15 (1) u Lift the door closing aid and turn it 90° to the right in the hole. Fig. 15 (2) u Tighten the screw using a T25 screwdriver. Fig. 15 (3) For all appliances: Fig. 16 u Remove the cover. Fig. 16 (1) * Depending on model and options 9 Door hinge change Fig. 17 u Place the bearing bracket on the other side and screw it on with a T20 screwdriver. Start with screw 2 at the bottom in the middle. Fig. 17 (2) u Screw in screws 3 and 4 tightly. Fig. 17 (3,4) u Insert the bearing pin completely. Make sure that the latching lug is pointing to the rear. Fig. 17 (5) Fig. 19 u The bottom side of door faces upwards: Turn the door. u Push the lug downwards with a slotted screwdriver. Fig. 19 (1) u Pull the door latch out of the guide. Fig. 19 (2) u Push the door latch into the guide on the other side. Fig. 19 (3) u The upper side of door faces upwards: Turn the door. 13.6 Moving the handles to the other side* For all appliances: Fig. 18 u Put the cover back on the other side. Fig. 18 (1) 13.5 Moving the door bearing parts to the other side For appliances without a soft stop: 10 * Depending on model and options Door hinge change Fig. 21 u Position the handle on the other side. Fig. 21 (1) w The screw holes must be exactly above each other. u Tighten the screw with a T15 screwdriver. Fig. 21 (2) u Position the covers on the side and push them on. Fig. 21 (3) w Ensure that they latch into place. 13.7 Fitting the door For all appliances: Fig. 20 u Pull off the cover. Fig. 20 (1) u Remove the screws with a T15 screwdriver. Fig. 20 (2) u Take off the handle. Fig. 20 (3) u Carefully lift up the side plugs with a slotted screwdriver and pull them out. Fig. 20 (4) u Insert the plugs again on the other side. Fig. 20 (5) Fig. 22 u Place the door on the lower bearing pins. u Align the top of the door with opening in the bearing bracket. Fig. 22 (1) u Insert the bolt and tighten with a T15 screwdriver. Fig. 22 (2) * Depending on model and options 11 Connecting device u Fit the protective cover to protect the door: Insert the protective cover and check that it is flush to the door. If not, insert the bolt fully. Fig. 22 (3) u Insert the plugs. Fig. 22 (4) 14 Connecting device 13.8 Aligning the door Danger of fire due to incorrect connection! Burns. Damage to the appliance. u Do not use an extension cable. u Do not use distributor blocks. For all appliances: WARNING Danger of injury due to door falling out! If the bearing parts are not screwed on tightly enough, the door may fall out. This can result in serious injuries. In addition, the door may not close with the result that the appliance does not cool properly. u Screw the bearing brackets on firmly with 4 Nm. u Check all screws and retighten them if necessary. u Align the doors flush with the appliance housing using the two slots in the bearing bracket if needed. To do this undo the middle screw in the bottom bearing bracket with the T20 tool supplied. Undo the remaining screws a little with the T20 tool or with a T20 screwdriver and align using the slotted holes. u Prop up the door: Take off the adjustable foot on the bearing bracket using the open-ended wrench SW10 until it comes into contact with the floor, then turn an addi‐ tional 90°. 13.9 Fitting the covers For appliances without a soft stop: WARNING NOTICE Danger of damage to incorrect connection! Damage to the appliance. u Do not connect the appliance to a stand-alone inverter, e.g. solar power systems and petrol generators. Note Only use the supplied mains cable. u A longer mains cable can be ordered from Customer Service. Ensure that the following conditions are met: - The type of current and voltage at the installation site match the information on the serial tag . - The socket is earthed according to the regulations and fused. - The fuse tripping current is between 10 and 16 A. - The socket is easily accessible. - The socket is not located behind the appliance but in areas a or b (a, b, c). u Check the electrical connection. u Insert the appliance plug (G) into the back of the appli‐ ance. Ensure that they latch into place. u Connect the mains plug to the power supply. w The Liebherr logo appears on the screen. w The display switches to the standby symbol. Fig. 23 The door is open 90°. u Position the bearing bracket and latch it in place. If necessary push it apart carefully. Fig. 23 (1) u Position the panel on the side and latch into place. Fig. 23 (2) Fig. 24 u Slide on the outer cover. Fig. 24 (1) u Close the upper door. Fig. 24 (2) 12 * Depending on model and options Connecting device * Depending on model and options 13 home.liebherr.com/fridge-manuals fridge Issue date: 20231213 Part number index: 7086333-00 Liebherr-Hausgeräte Marica EOOD Bezirk Plovdiv 4202 Radinovo Bulgarien ">

Public link updated
The public link to your chat has been updated.
Advertisement