Mr. Heater | 4000DF | Operating instructions | Mr. Heater 4000DF Operating instructions

Operating Instructions and Owner’s Manual
INSTRUCTIONS CAREFULLY: Read
heatstar
mr. heater READ
and follow all instructions. Place instructions in
BY eNERCO
4000DF 6000DF
a safe place for future reference. Do not allow
anyone who has not read these instructions to
assemble, light, adjust or operate the heater.
Model
Model
4000DF3500DF
6000DF
4000DF3500DF
6000DF
4000DF 6000DF
Smoky Mountain Emporium Ltd
828-670-1970
www.smgeneralstore.com
sales@smgeneralstore.com
DIRECT FIRED
PORTABLE HEATER
the information in this manual is not followed exactly, a fire or explosion
WARNING: Ifmay
result causing property damage, personal injury or loss of life.
­— Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any
other appliance.
— Service must be performed by a qualified service agency.
This is an unvented portable heater. It uses air (oxygen) from the area in which it is used. Adequate
combustion and ventilation air must be provided. Refer to page 5.
ENERCO GROUP, INC., 4560 W. 160TH ST., CLEVELAND, OHIO 44135 • 800-251-0001
07/08 #50125
WARNING:
WARNING:
YOUR SAFETY IS IMPORTANT TO YOU AND TO OTHERS,
SO PLEASE READ THESE INSTRUCTIONS BEFORE YOU
OPERATE THIS HEATER.
NOT FOR HOME OR RECREATIONAL VEHICLE USE
WARNING:
GENERAL HAZARD WARNING:
FIRE, BURN, INHALATION, AND EXPLOSION HAZARD.
KEEP SOLID COMBUSTIBLES, SUCH AS BUILDING MATERIALS, PAPER OR CARDBOARD, A SAFE DISTANCE
AWAY FROM THE HEATER AS RECOMMENDED BY THE
INSTRUCTIONS NEVER USE THE HEATER IN SPACES
WHICH DO OR MAY CONTAIN VOLATILE OR AIRBORNE
COMBUSTIBLES, OR PRODUCTS SUCH AS GASOLINE,
SOLVENTS, PAINT THINNER, DUST PARTICLES OR UNKNOWN CHEMICALS.
FAILURE TO COMPLY WITH THE PRECAUTIONS AND
INSTRUCTIONS PROVIDED WITH THIS HEATER, CAN
RESULT IN DEATH, SERIOUS BODILY INJURY AND
PROPERTY LOSS OR DAMAGE FROM HAZARDS OF FIRE,
EXPLOSION, BURN, ASPHYXIATION, CARBON MONOXIDE POISONING, AND/OR ELECTRICAL SHOCK.
ONLY PERSONS WHO CAN UNDERSTAND AND FOLLOW
THE INSTRUCTIONS SHOULD USE OR SERVICE THIS
HEATER.
IF YOU NEED ASSISTANCE OR HEATER INFORMATION
SUCH AS AN INSTRUCTIONS MANUAL, LABELS, ETC.
CONTACT THE MANUFACTURER.
WARNING:
The State of California requires the following warning:
COMBUSTION BY-PRODUCTS PRODUCED WHEN USING THIS PRODUCT CONTAIN CARBON MONOXIDE,
A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA
TO CAUSE CANCER AND BIRTH DEFECTS (OR OTHER
REPRODUCTIVE HARM).
Contents
WARNING:
WARNINGS................................................................................... 2
READ THE INSTRUCTIONS GIVEN IN THIS
MANUAL BEFORE USING THE APPLIANCE.
SPECIFICATIONS............................................................................ 3
• DO NOT USE GASOLINE, NAPHTHA OR VOLATILE
FUELS.
Safety devices........................................................................... 4
operation.................................................................................. 4
MAINTENANCE............................................................................. 5
• THE ELECTRICAL SYSTEM TO WHICH THE APPLIANCE
IS CONNECTED MUST COMPLY WITH ALL SAFETY
REGULATIONS IN FORCE. A RESIDUAL CURRENT
CIRCUIT BREAKER MUST BE PROVIDED ON THE MAIN
DISTRIBUTION BOARD.
TROUBLESHOOTING..................................................................... 6
wiring diagrams...................................................................... 7
parts list.................................................................................... 8
• UNPLUG THE HEATER BEFORE ATTEMPTING ANY
SERVICE OR MAINTENANCE.
• ALWAYS CHECK THE POWER SUPPLY CABLE BEFORE
USE. IT MUST NOT BE BENT, CRUSHED, OR ANYWAY
DAMAGED.
• THE POWER SUPPLY CABLE MUST BE REPLACED ONLY
BY QUALIFIED PERSONNEL.
• ONLY USE AN ORIGINAL H07RN-F POWER CABLE
WITH WATERPROOF PLUG.
• DO NOT TOUCH THE EXHAUST GAS OUTLET. DANGER
OF BURNS!
ENERCO GROUP, INC. |Direct Fired Portable Heater
2
Operating Instructions and Owner’s Manual
Important
• Never block air inlet (rear) or air outlet (front).
• In case of very low temperatures add kerosene to the
heating oil.
• Make sure heater is always under surveillance and keep
children and animals away from it;
• Before starting the heater always check free rotation of
ventilator fan.
• Unplug heater when not in use.
Before using the heater, read and understand all instructions and
follow them carefully. The manufacturer is not responsible for
damages to goods or persons due to improper use of units.
General Recommendations
The direct-fired heater runs on diesel fuel. This direct combustion
heater exhausts hot air and the combustion products into
the room, while those with indirect combustion are fitted
with a flue to take the fumes away through the chimney.
Always follow local ordinances and codes when using this
heater:
• Read and follow this owner’s manual before using the
heater.
• Use only in places free of flammable vapors or high dust
content.
• Never use heater in immediate proximity of flammable
materials (the minimum distance must be 6 ft.).
• Make sure fire fighting equipment is readily available.
• Make sure sufficient fresh outside air is provided according
to the heater requirements. Direct combustion heaters
should only be used in well vented areas in order to avoid
carbon monoxide poisoning.
MH 3500DF
4000DF
mh 4000DF
HS 3500DF
4000DF
hs 4000DF
mh 6000DF
hs 6000DF
[kBTU/h]
400
610
[cfm]
2.500
2.800
[kBTU/h]
-
-
[gal/h]
12.83
4.46
[lb/h]
19.58
30.84
1
1
TECHNICAL SPECIFICATIONS
Heat input
Air flow
Fuel Type
Diesel/Kerosene/#1-2 Fuel Oil
Heat output
Fuel consumption
Phase
Power supply
Voltage
[V]
120
120
Frequency
[Hz]
60
60
[W]
1,170
1,040
[A]
8.30
10.50
[USgal/h]
2.00-30° S
3.00-80°S
[psi]
174
217
[in WC]
-
-
[°F]
-
-
[in]
a=0.59
a=1.00
N°
-
-
[in]
-
-
Electric consumption
Nozzle
Pump pressure
Max static pressure
Recommended max. temp. in the air
duct
Adjustment of combustion air flap
Flue diameter
Compulsory flue draft
[in WC]
-
-
Tank capacity
[gal]
27.7
35.7
Dimensions, L x W x H
[in]
62.4x27.6x39
67.9x27.6x41.2
Net Weight
[lb]
222
246
ENERCO GROUP, INC. |Direct Fired Portable Heater
3
Operating Instructions and Owner’s Manual
Operation
• Install the heater on a flat, level floor in a steady position.
• It is forbidden to connect direct-fired heaters to air ducts.
Before any attempt of starting the heater is made, check that
your electrical supply conforms to the data on the model plate.
Warning
• DO NOT USE GASOLINE, NAPHTHA OR VOLATILE FUELS.
• STOP HEATER BEFORE ADDING FUELS.
• ALWAYS FILL OUTDOORS AWAY FROM OPEN FLAME
• DO NOT USE EXTERNAL FUEL SOURCE.
• DO NOT OPERATE HEATER WHERE FLAMMABLE LIQUIDS
OR VAPORS MAY BE PRESENT.
• DO NOT START HEATER WHEN CHAMBER IS HOT
• DO NOT START HEATER WHEN EXCESS FUEL HAS ACCUMULATED IN THE CHAMBER.
• DO NOT PLACE COOKING UTENSILS ON TOP OF THE
HEATER.
• PLUG ELECTRICAL CORD INTO A PROPERLY GROUNDED
THREE-PRONG RECEPTACLE.
Control Board
1
3
4
2
5
ON
0
ON
1
RESET BUTTON WITH CONTROL LAMP
2
CONTROL LAMP
3
MAIN SWITCH
4
ROOM THERMOSTAT PLUG
5
POWER CORD
The generator can only work automatically when a control device,
such as for example a thermostat or a timer, is connected to the
generator. Connection to the generator is made by removing the
socket cover(4) and inserting the thermostat plug.
To start the machine you must:
•If connected to the thermostat, turn the switch to (ON + );
•If not connected to the thermostat, turn the switch to (ON).
When unit is started for the first time or is started after the oil
tank has been totally emptied, the flow of oil to the burner may
be impaired by air in the circuit. In this case the control box will
cut out the heater and it might be necessary to renew the starting
procedure once or twice by depressing the reset button (1).
Gap of Electrodes
Should the heater not start, check that oil tank
is full and depress reset button (1).
Should the heater still not work, please refer to chapter
“OBSERVED FAULTS, CAUSES AND REMEDIES”.
X
Stopping the Heater
Y
Set main switch (3) on “0” position or turn thermostat or other
control device on lowest setting.
Z
The flame goes out and the fan continues to work for approx.
90sec. cooling the combustion chamber.
Safety Devices
Models
X
Y
Z
4000 DF
0.157 in
0.098 in
0.157 in
6000 DF
0.157 in
0.098 in
0.157 in
The unit is fitted with an electronic flame control box. In case of
malfunction this box will cut in and stop the heater, at the same
time the pilot lamp in the control box reset button (1) will light up.
Clearances
Heaters are also equipped with an overheat thermostat safety
cutout which will stop the heater in case of overheating. This
thermostat will reset automatically but you will have to depress
button (1) on control box before being able to restart the heater.
The following minimum safety clearances from materials or objects
in the surroundings of the heater must be ensured:
Transport
Sides
Top
2.5 ft.
6 ft.
Air Inlet 2.5 ft.
Air outlet 12 ft.
Warning
• Before making any attempt to restart heater find and eliminate reason of overheating.
• Floors and ceilings must be made of fireproof materials in
the room where the heater is operated.
• The air inlet and outlet must never be blocked for any
reason.
ENERCO GROUP, INC. |Direct Fired Portable Heater
Before heater is moved it must be stopped and unplugged. Before
moving the heater wait till it has totally cooled off and make sure
oil tank cap is securely fixed.
4
Operating Instructions and Owner’s Manual
The hot air generators with wheels must be wheeled. The
suspended version which has no wheels must be transported with
adequate machinery.
Maintenance
Preventive and regular maintenance will ensure a long trouble free
life to your heater.
Warning
• Never service heater while it is plugged in, operating or hot.
Severe burns or electrical shock can occur.
Every 50 hours of operation: disassemble filter and wash with
clean oil, remove upper body parts and clean inside and ventilator
with compressed air, check correct attachment of H.V. connectors
to the electrodes and check H.V. cables, remove burner assembly,
clean and check electrode settings, adjust according to scheme
“gap OF ELECTRODES”.
COLUMN INTENTIONALLY LEFT BLANK
ENERCO GROUP, INC. |Direct Fired Portable Heater
5
Operating Instructions and Owner’s Manual
Troubleshooting
TROUBLE
Cause
SOLUTION
Motor does not start, no ignition
No electrical current
Check mains (should be 120 V – 1~ – 60 Hz)
Check proper positioning and functioning of switch
Check fuse
Motor starts, no ignition or cuts out
Wrong setting of room thermostat or other control
Check correct setting of heater control. If thermostat, make
sure selected temperature is higher than room temperature
Thermostat or other control
defective
Replace control device
Electrical motor defective
Replace electrical motor
Electrical motor bearings
defective
Replace electrical motor bearings
Burned out condenser
Replace condenser
Electric ignitor defective
Check connection of H.V. Ieads to electrodes and transformer
Check electrodes setting (see scheme “gap OF ELECTRODES”)
Check electrodes for cleanliness
Replace H.V. transformer
Flame control box defective
Replace control box
Photocell defective
Clean or replace photocell
Not enough or no fuel at all
at burner
Check state of motor-pump plastic coupling
Check fuel line system including fuel filter for possible leaks
Clean or replace oil nozzle
Solenoid defective
Check electrical connection
Check thermostat LI
Clean or replace solenoid
Motor starts, heater emits smoke
Not enough combustion air
Make sure air inlet and outlet are free
Check setting of combustion air flap
Clean burner disc
Too much combustion air
Check setting of combustion air flap
Fuel contaminated or contains water
Drain fuel in tank with clean fuel
Air leaks in fuel circuit
Check the seals on the ducts and the diesel filter
Not enough fuel at burner
Check pump pressure
Clean oil filter
Clean or replace fuel nozzle
Too much fuel at burner
Check pump pressure
Replace nozzle
Heater does not stop
Solenoid
Replace solenoid coil or complete solenoid
If heater still not working properly, please revert to nearest authorized dealer.
ENERCO GROUP, INC. |Direct Fired Portable Heater
6
Operating Instructions and Owner’s Manual
Wiring Diagram
4000 and 6000 Series Models
Drawing Legend
FU
Fuse
RV
Control
IT
Transformer H.V.
TA
Room Thermostat
LI1
Overheat Thermostat
RE
Relays
EV1
Solenoid Valve 1°
AP
Control Box
FO
Photocell
PA
Air pressure control
CO
Condenser
RF
Heater filter
MV
Fan Motor
FA
Fan thermostat
ST
Electric pilot
PE Ground
ENERCO GROUP, INC. |Direct Fired Portable Heater
7
Operating Instructions and Owner’s Manual
4000DF and 6000DF Series Direct-Fired Portable Heater
B
70
31
59
60
58
71
61 62 63
72
57
01
56
38
73
02
75
79
54
80
74
81
55
64
65
03
77
53
52
76
51
66 67
46
78
69
68
45
35
34
47
31
49 48
33
50
06
32
30
B
29
36
38
28
04
27
07
37
38
26
A
05
37
39
19
08
09
39
43
44
42
21
24
25
17
22
23
10
20
13
A
82
11
19
14
83
84
13
15
16
87
88
18
14 17
12
85
75
12
76
86
ENERCO GROUP, INC. |Direct Fired Portable Heater
8
Smoky Mountain Emporium Ltd
828-670-1970
Operating Instructions and Owner’s Manual
www.smgeneralstore.com
sales@smgeneralstore.com
HS-MH3500DF, 4000DF-6000DF Portable Heater Parts List BM2
NO.
01
HS#
50027
03
04
50037
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
50160
50045
50161
50163
50165
50048
50049
50167
50050
50051
50052
50054
50055
50056
50057
50058
50059
50060
50061
50062
50063
50064
50170
50065
50070
50067
50068
50071
50072
50073
50074
33
35
50077
36
42
44
45
50085
BM2 #
3500 4000 6000
DESCRIPTION
*
*
G06139-9010
outlet cone
*
G06230
combustion chamber
*
G06231
*
G06232
*
G06143-9010
cover protection
*
G06233-9010
upper body
*
G06234-9010
*
G06235-9010
*
G06236-9010
lower body
*
G06237-9010
*
G06238-9010
*
*
G06240
air flap
*
E10678-110
motor 450W with condenser
*
*
E10679-110
motor 750W with condenser
*
E11230
condenser 40µF
*
*
E11241
condenser 90µF
*
G06125-9010
motor flange
*
*
G06239-9010
*
T10260
fan blade ø350 18°
*
T10215-B
fan blade ø496 18°
*
T10263
fan blade ø500 18°
*
P30169
inlet grill
*
*
P30129
*
*
*
I40330
tube BP 1/4"FF L.420mm
*
*
*
I20104
nipple FE 1/4"mm
*
*
*
02AC575-1
oil filter pre-heater 1/4"
*
*
*
G06104-9005
filter support
*
*
*
I40329
tube BP 1/4"FF L.260mm
*
*
*
I20176-9005
handle
*
*
*
C30319
plug
*
*
P20177-9005
foot
*
P20180-9005
*
*
*
I40331
tube BP 1/4"F L. 580mm
*
*
I30696
pick-up tube L. 220mm
*
I30698
pick-up tube L. 290mm
*
*
*
I30737
nipple 1/4"m-m12x1.75m
*
*
*
G06068-9005
power lead hook
*
G06127-9005
fuel tank 105 liters
*
G06128-9005
fuel tank 105 liters
*
G06146-9005
fuel tank 135 liters
*
*
*
C30367
fuel cap
*
*
*
G06129-9005
wheel axle
*
*
G06106-9005
wheel axle support
*
G06107-9005
*
*
*
C10546
wheel 260-25
*
*
*
M20202
spring washer
*
*
*
I25019
drain plug
*
*
*
C30350
o-ring 30x2.62
*
*
G00248
electrical components dwr
*
G00251
*
*
*
P50127
control box cover
*
G06242-9010
base
*
*
G06241-9010
*
*
*
C30323
cable protection ø10
*
*
*
C30372
cable protection ø35
*
*
*
E50102
pressure switch
NO.
46
51
52
53
56
57
58
59
63
64
65
66
67
68
69
70
71
HS#
50086
50246
50093
50092
50096
50097
50098
50319
50320
50014
50013
50011
50009
50008
50321
50006
50126
72
73
74
76
77
78
79
82
83
84
85
86
87
90
91
92
93
94
95
96
15
50131
50133
50134
50322
50135
50323
50324
50139
50140
50141
50195
50143
50144
50145
50325
50336
50337
BM2 #
3500 4000 6000
DESCRIPTION
*
*
*
G06072
sleeve ø8 x ø6 x 9.5
*
*
*
G06153
electrial components dwr
*
*
*
E20508
fuse holder
*
*
*
E10313
fuse (6x30) 20A
*
*
*
E20319
terminal board
*
*
*
E11125
relay finder 65.31 AC
*
*
*
E20305
terminal board
*
*
*
E10930
transformer HT BRHAMA
*
*
*
E40124
control box BRAHMA
G06073
*
*
*
plate for elect. Components
E10102-P
*
*
*
switch on-off
E20614
*
*
*
thermostat plug 3P+T
E20665
*
*
*
thermostat cap
E30443
*
*
*
elect. Wire w/plug and fastener
E11030
*
*
*
lamp 120V
T20357
*
*
nozzle 2.00 GPH 80° W
T20327
*
nozzle 3.00 GPH 80° W
G01077
*
*
turbo disc
G07025
*
I33005
*
*
*
nozzle support
G06228
*
*
burner flange ø 102mm
G06229
*
I31034
*
*
*
nut M14
I40192
*
*
*
micropipe
E10215
*
*
*
electrode
G02078
*
*
H.T. cables 90° BRAHMA
G02076
*
H.T. cables 90° COFI
E50328
*
*
*
photo cell
T20443-1
*
pump Danfoss BFA01-R4
T20411-1
*
*
pump Danfoss BFP11-R5
T20118
*
*
*
solenoid spool Danfoss
T20117
*
*
*
solenoid valve Danfoss
E10513
*
coupling K1
E10514
*
*
coupling K2
T20241
*
*
*
o-ring kit oil filter
T20242
*
*
*
filter cartridge
E20418
*
*
*
stop button
E50327
*
*
*
photo cell holder
G06222-9010
*
*
*
photo cell mounting plate
E50441
*
*
*
pressure switch 100Pa
I40332
*
*
*
silicone pipe ø4x9
I31131
*
*
*
connection straight ø6
T20442
*
*
*
solenoid valve cable
Ed. 05/09
Operating Instructions and Owner’s Manual
READ INSTRUCTIONS CAREFULLY: Read
heatstar
mr. Heater and follow all instructions. Place instructions in
BY eNERCO
4000DF 6000DF
a safe place for future reference. Do not allow
anyone who has not read these instructions to
assemble, light, adjust or operate the heater.
Model
Model
4000DF3500DF
6000DF
4000DF3500DF
6000DF
4000DF 6000DF
WARNING:
USE ONLY MANUFACTURER’S REPLACEMENT PARTS. USE OF ANY OTHER PARTS
COULD CAUSE INJURY OR DEATH. REPLACEMENT PARTS ARE ONLY AVAILABLE
DIRECT FROM THE FACTORY AND MUST BE INSTALLED BY A QUALIFIED SERVICE
AGENCY.
PARTS ORDERING INFORMATION:
PURCHASING: Accessories may be purchased at any Mr. Heater/HeatStar local dealer
or direct from the factory
FOR INFORMATION REGARDING SERVICE
Please call Toll-Free 800-251-0001 • www.enerco-mrheater.com
Our office hours are 8:30 AM – 5:00 PM, EST, Monday through Friday.
Email to: techservice@enerco-mrheater.com
Please include the model number, date of purchase, and description of problem in all
communication.
LIMITED WARRANTY
The company warrants this product to be free from imperfections in material or workmanship,
under normal and proper use in accordance with instructions of The Company, for a period
of one year from the date of delivery to the buyer. The Company, at its option, will repair or
replace products returned by the buyer to the factory, transportation prepaid within said one
year period and found by the Company to have imperfections in material or workmanship.
If a part is damaged or missing, call our Technical Support Department at 800-251-0001.
Address any Warranty Claims to the Service Department, Enerco Group, Inc., 4560 W. 160TH
ST., Cleveland, Ohio 44135. Include your name, address and telephone number and include
details concerning the claim. Also, supply us with the purchase date and the name and address
of the dealer from whom you purchased our product.
The foregoing is the full extent of the responsibility of the Company. There are no other
warranties, express or implied. Specifically there is no warranty of fitness for a particular
purpose and there is no warranty of merchantability. In no event shall the Company be liable for
delay caused by imperfections, for consequential damages, or for any charges of the expense
of any nature incurred without its written consent. The cost of repair or replacement shall be
the exclusive remedy for any breach of warranty. There is no warranty against infringement of
the like and no implied warranty arising from course of dealing or usage of trade. This warranty
will not apply to any product which has been repaired or altered outside of the factory in any
respect which in our judgment affects its condition or operation.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you. This Warranty gives you specific legal
rights, and you may have other rights which vary from state to state.
Enerco Group, Inc. reserves the right to make changes at any time, without notice or
obligation, in colors, specifications, accessories, materials and models.
ENERCO GROUP, INC., 4560 W. 160TH ST., CLEVELAND, OHIO 44135 • 800-251-0001
Mr. Heater is a registered trademark of Enerco Group, Inc.
© 2004, ENERCO GROUP, INC. All rights reserved
ENERCO GROUP, INC. |Direct Fired Portable Heater
10
Operating Instructions and Owner’s Manual
Smoky Mountain Emporium Ltd
828-670-1970
www.smgeneralstore.com
sales@smgeneralstore.com
07/08 #50125
Download PDF