Bloomfield Integrity 8746 Specifications

601
10 Sunnen Drive
St. Louis, MO 63143
telephone: 314-678-6336
fax: 314-781-2714
www.bloomfieldworldwide.com
OWNERS MANUAL
for
INTEGRITY™
DECANTER
COFFEE BREWERS
MODELS
9003
9010 9012
9016
Includes:
Installation
Use & Care
Servicing Instructions
Model 9016 Brewers
with optional
8900-Series Glass Decanters
p/n 2M-75815 Rev. J
M601
120511
WARRANTY STATEMENT
All equipment manufactured by Bloomfield is warranted against defects
in materials and workmanship for the time periods listed in the chart
starting from the date the equipment is placed into service and is for the
benefit of the original purchaser:
THE FOREGOING OBLIGATION IS EXPRESSLY GIVEN IN LIEU
OF ANY OTHER WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE, WHICH ARE
HEREBY EXCLUDED.
BLOOMFIELD, LLC SHALL NOT BE LIABLE FOR INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES
FROM ANY CAUSE WHATSOEVER.
Equipment
pour over, automatic coffee brewers
EBC, EMAX coffee brewers
* EBC, EMAX coffee brewer control
POD coffee brewers
ECO coffee brewers
coffee warmers
tea brewers
tea dispensers
tea dispenser BBTea
hot water machines
thermal servers
airpots
decanters
This warranty is void if it is determined that upon inspection by an
authorized service agency that the equipment has been modified,
misused, misapplied, improperly installed, or damaged in transit or by fire, flood or act of God.
Parts
2 yrs.
2 yrs.*
3 yrs.
1 yr.
1 yr.
1 yr.
2 yrs.
1 yr.
1 yr.
2 yrs.
90 days
30 days
no warranty
Labor
2 yrs.
2 yrs.
no labor
1 yr.
1 yr.
1 yr.
2 yrs.
1 yr.
no labor
2 yrs.
no labor
no labor
no warranty
It also does not apply if the serial nameplate has been removed or unauthorized service personnel perform service. The prices
charged by Bloomfield for its products are based upon the limitations in this warranty. Seller’s obligation under this warranty
is limited to the repair of defects without charge by a Bloomfield Authorized Service Agency or one of its sub-agencies. This
service will be provided on customer’s premises for non-portable models. Portable models (a device with a cord and plug or a
dispenser) must be taken or shipped to the closest authorized service agency, transportation charges prepaid, for services.
Agencies are located in principal cities, please visit our website to locate one.
This warranty is valid in the United States and Canada and void elsewhere. Please consult your classified telephone directory
or your food service equipment dealer; or, for information and other details concerning warranty, write to:
Service Parts Department; Bloomfield
10 Sunnen Drive, St. Louis, MO 63143
Phone: (314) 678-6336 : Fax: (314) 781-2714
Technical@ bloomfieldworldwide.com / www.bloomfieldworldwide.com
1. Resetting of safety thermostats, circuit breakers, overload protectors, or fuse replacements.
2. All problems due to operation at voltages other than specified on equipment nameplates - conversion to correct voltage
must be the customer’s responsibility.
3. All problems due to electrical connections not made in accordance with electrical code requirements and wiring diagrams
supplied with the equipment.
4. Replacement of items subject to normal wear, to include such items as knobs and light bulbs. Normal maintenance
functions including adjustment of thermostats, microswitches, and replacement of fuses and indicating lights are not
covered under warranty.
5. All problems due to inadequate water supply, such as fluctuating, or high or low water pressure.
6. All problems due to mineral/calcium deposits, or contamination from chlorides/chlorines. De-liming is considered a
preventative maintenance function and is not covered by warranty.
7. Full use, care and manuals may or may not be sent with each unit, only a condensed version. Please visit our web site to
download the full version.
8. Travel mileage is limited to fifty (50) miles from an authorized service agency or one of its sub-service agencies.
9. All labor shall be performed during normal working hours. Overtime premium shall be charged to the customer.
10. All genuine Bloomfield replacement parts are warranted for ninety (90) days from date of purchase on non- warranted
equipment. Any use of non-genuine Bloomfield parts completely voids any warranty.
11. Installation, labor and job checkouts are not considered warranty.
12. Charges incurred by delays, waiting time or operating restrictions that hinder the service technicians ability to perform
services are not covered by warranty. This includes institutional and correctional facilities.
SHIPPING DAMAGE CLAIMS PROCEDURE
NOTE: For your protection, please note that equipment in this shipment was carefully inspected and packaged by skilled
personnel before leaving the factory. Upon acceptance of this shipment, the transportation company assumes full responsibility
for its safe delivery.
IF SHIPMENT ARRIVES DAMAGED:
1. VISIBLE LOSS OR DAMAGE: Be certain that any visible loss or damage is noted on the freight bill or express receipt,
and that the note of loss or damage is signed by the delivery person.
2. FILE CLAIM FOR DAMAGE IMMEDIATELY: Regardless of the extent of the damage.
3. CONCEALED LOSS OR DAMAGE: if damage is unnoticed until the merchandise is unpacked, notify the
transportation company or carrier immediately, and file “CONCEALED DAMAGE” claim with them. This must be done
within fifteen (15) days from the date the delivery was made to you. Be sure to retain the container for inspection.
Bloomfield cannot assume liability for damage or loss incurred in transit. We will, however, at your request, supply you with the
necessary documents to support your claim.
601 p/n 2M-75815 9003, 9010, 9012, 9016 Decanter Coffee Brewer
BLOOMFIELD SERVICE POLICY AND PROCEDURE GUIDE ADDITIONAL WARRANTY EXCLUSIONS
TABLE OF CONTENTS
WARRANTY
STATEMENT xi
SPECIFICATIONS 1
FEATURES & OPERATING CONTROLS
2
PRECAUTIONS & GENERAL INFORMATION 3
AGENCY APPROVAL INFORMATION
3
INSTALLATION INSTRUCTIONS
4
OPERATION 6
BREWING COFFEE
8
CLEANING INSTRUCTIONS
9
TROUBLESHOOTING SUGGESTIONS
10
SERVICING INSTRUCTIONS11
Deliming Instructions
16
EXPLODED VIEWS & PARTS LISTS
18
WIRING DIAGRAMS22
Thank You for purchasing this
Bloomfield appliance.
Proper installation, professional
operation and consistent
maintenance of this appliance will
ensure that it gives you the very
best performance and a long,
economical service life.
This manual contains the
information needed to properly
install this appliance, and to use,
care for and maintain or repair the
appliance in a manner which will
ensure its optimum performance.
SPECIFICATIONS
MODEL
9003
*9003CA
3W IN-LINE, POUR-OVER
VOLTS
WATTS
AMPS 1ø
POWER SUPPLY CORD
120
1800
15
NEMA 5-15P
120
1500
12.5
NEMA 5-15P
9010
120
2300
19
NEMA 5-20P
9012
120
1800
15
NEMA 5-15P
120
1500
12.5
NEMA 5-15P
9016
120/240
3800
17
NOT PROVIDED
9016EX
220-240
3800
16.5
NOT PROVIDED
*9012CA
601 p/n 2M-75815 9003, 9010, 9012, 9016 Decanter Coffee Brewer
STYLE
3W IN-LINE, FAUCET
* 120V Canadian units are 1500 watts maximum.
1
FEATURES AND OPERATING CONTROLS
HOT WATER FAUCET
(certain models)
IL1614a
Fig. 1 Features & Operating Controls
2
601 p/n 2M-75815 9003, 9010, 9012, 9016 Decanter Coffee Brewer
WATER LINE CONNECTION
PRECAUTIONS AND GENERAL INFORMATION
WARNING
WARNING
WARNING
WARNING
WARNING: ELECTRIC SHOCK HAZARD
All servicing requiring access to non-insulated components must be performed by qualified
service personnel. Do not open any access panels which require the use of tools. Failure to heed this warning can result in electrical shock.
WARNING: INJURY HAZARD
All installation procedures must be performed by qualified personnel with full knowledge of all
applicable electrical and plumbing codes. Failure could result in property damage and
personal injury.
WARNING: ELECTRIC SHOCK HAZARD
Brewer must be properly grounded to prevent possible shock hazard. DO NOT assume a
plumbing line will provide such a ground. Electrical shock will cause death or serious Injury.
WARNING: BURN HAZARD
This appliance dispenses very hot liquid. Serious bodily injury from scalding can occur from
contact with dispensed liquids.
This appliance is intended for commercial use only.
This appliance is intended for use to brew beverage products for
human consumption. No other use is recommended or
authorized by the manufacturer or its agents.
This appliance is intended for use in commercial establishments,
where all operators are familiar with the appliance use,
limitations and associated hazards. Operating instructions and
warnings must be read and understood by all operators and
users.
601 p/n 2M-75815 9003, 9010, 9012, 9016 Decanter Coffee Brewer
Except as noted, this piece of equipment is made in the USA and
has American sizes on hardware. All metric conversions are approximate and can vary in size.
The following trouble shooting, component views and parts lists
are included for general reference, and are intended for use by
qualified service personnel.
This manual should be considered a permanent part of this
appliance. The manual must remain with the appliance if it is
sold or moved to another location.
AGENCY APPROVAL INFORMATION
This brewer is
and
C
listed under UL file E9253.
This brewer meets
Standard 4 only when installed,
operated and maintained in accordance with the enclosed
instructions.
3
CAUTION:
EQUIPMENT DAMAGE
DO NOT plug in or energize this
appliance until all Installation
Instructions are read and followed.
Damage to the Brewer will occur if
these instructions are not followed.
CAUTION:
BURN HAZARD
Exposed surfaces of the
appliance, brew chamber and
decanter may be HOT to the
touch, and can cause serious
burns.
INSTALLATION INSTRUCTIONS
READ THIS CAREFULLY BEFORE STARTING THE INSTALLATION
CAUTION:
EQUIPMENT DAMAGE
DO NOT plug in or energize this
appliance until all Installation
Instructions are read and
followed. Damage to the Brewer
will occur if these instructions are
not followed.
CAUTION:
Unstable
Equipment Hazard
It is very important for safety
and for proper operation that the
brewer is level and stable when
standing in its final operating
position. Provided adjustable,
non-skid legs must be installed at
each corner of the unit. Failure
to do so will result in movement
of the brewer which can cause
personal Injury and/or damage to
brewer.
NOTE: Water supply inlet line
must meet certain minimum
criteria to insure successful
operation of the brewer.
Bloomfield recommends 1/4”
copper tubing for installation of
less than 12 feet and 3/8” for
more than 12 feet from a 1/2”
water supply line.
Unpack the unit. Inspect all components for completeness and
condition. Ensure that all packing materials have been removed
from the unit.
Verify that the Spray Head Gasket and Spray Disk are properly
installed.
LEVELING THE UNIT
Verify that an adjustable leg is installed at each corner of the
brewer.
Set brewer in its operating location. Level the brewer. A spirit
level should be placed on the top of the unit, at the edge, as a
guide when making level adjustments.
Level the unit from left to right and front to back by turning the
adjustable feet. Be sure all four feet touch the counter to prevent
tipping.
PLUMBER’S INSTALLATION INSTRUCTIONS
Brewer should be connected to a POTABLE WATER, COLD
WATER line. Flush water line before connecting to brewer.
DO NOT use a saddle valve with a self-piercing tap for the water
line connection. Such a tap can become restricted by waterline
debris. For systems that must use a saddle tap, shut off the
main water supply and drill a 3/16” (minimum) tap for the saddle
connection, in order to insure an ample water supply. Remember
to flush the line prior to installing the saddle.
The brewer must be installed on a water line with average
pressure between 20 PSI and 90 PSI. If your water pressure
exceeds 90 PSI at anytime, a pressure regulator must be
installed in the water supply line to limit the pressure to not more
than 90 PSI in order to avoid damage to lines and solenoid.
A water shut-off valve should be installed on the incoming water
line in a convenient location (Use a low restriction type valve,
such as a 1/4-turn ball valve, to avoid loss of water flow thru the
valve.
NSF requires that the brewer be able to be moved for cleaning
underneath. A flex line or loops of copper tubing will satisfy this
requirement. See Figure 2 below.
Fig. 2 Water Supply
Installation
IL1615
4
601 p/n 2M-75815 9003, 9010, 9012, 9016 Decanter Coffee Brewer
IMPORTANT:
To enable the installer to make
a quality installation and to
minimize installation time, the
following suggestions and tests
should be done before the actual
unit installation is started:
INSTALLATION INSTRUCTIONS (continued)
In some areas, local codes require a backflow preventer (check
valve) to be installed on the inlet water line. If a backflow
preventer is used, you must install a water hammer arrester in
the incoming line, between the backflow preventer and the
brewer inlet, as far away from the brewer as space will allow.
This will relieve the excessive back pressures that can cause
faucet leaks and solenoid malfunctions.
ELECTRICIAN’S INSTALLATION INSTRUCTIONS
REFER TO ELECTRICAL SPECIFICATIONS - Page 1
Check the nameplate to determine correct electrical service
required for the brewer to be installed.
IMPORTANT: Before connecting to electricity, make sure
automatic brewers are connected to the water supply.
Models 9003, 9010 & 9012 are equipped with a cord and plug.
They require a 115 - 125 volt 20 amp circuit (50/60 Hz, 2 wire
plus ground, with NEMA 5-15R or 5-20R Receptacle).
IMPORTANT: The ground prong of the plug is part of a system
designed to protect you from electrical shock in the event of
internal damage. Never cut off the ground prong nor twist a
blade to fit an existing receptacle. Contact a licensed electrician
to install the proper circuit and receptacle.
601 p/n 2M-75815 9003, 9010, 9012, 9016 Decanter Coffee Brewer
Models 9016 must be wired by an electrician, and require a
115/230V 20A circuit (50/60 Hz, 2 hot legs / 1 neutral leg, plus
ground). Remove front panel to gain access to terminal block.
Green terminal must be connected to a suitable building ground.
Circuit must be capable of 3800 Watts. See figure 3 at right.
IMPORTANT: Wiring must be installed in approved solid or
flexible conduit, and must be secured to the brewer with a strain
relief (to be provided by the installer).
Models 9016EX must be wired by an electrician, and require
a 220-240V 20A circuit (50/60 Hz, 2 hot legs plus ground).
Remove front panel to gain access to terminal block. Green
terminal must be connected to a suitable building ground.
Circuit must be capable of 3800 Watts. Refer to 9016EX wiring
diagram on page 23.
NOTE: This equipment must
be installed to comply with
applicable federal, state and
local plumbing codes and
ordinances.
WARNING
WARNING:
SHOCK HAZARD
Brewer must be properly
grounded to prevent possible
shock hazard. DO NOT
assume a plumbing line will
provide such a ground.
Electrical shock will cause death
or serious injury.
IMPORTANT: Do not connect
brewer to electrical power until
the tank is filled with water.
Pour water into the pour-over
opening until water flows from
the brew head.
IMPORTANT:
Supply power must match
nameplate for voltage and
phase. Connecting to the wrong
voltage will damage the brewer
or result in decreased
performance. Such damage is
not covered by warranty.
IL1616
IMPORTANT: Wiring must be installed in accordance with local
codes and ordinances.
Fig. 3 115/240 Volt Terminal Block
5
OPERATION
IL1617
Fig. 4 Brewer Operation Diagram
A. START-UP
For initial start-up, or if the brewer has not been used for an
extended period of time:
•
Be sure spray disk and brew gasket are properly installed in the brew head.
•
Be sure the water supply is properly connected and the water
supply valve is turned ON.
•
Be sure the WATER TANK IS FILLED
BEFORE plugging the brewer into a receptacle, or otherwise connecting brewer to electrical power the water tank must be filled. Place an empty decanter under the brew head. Lift the pour-over cover then pour warm tap water into the pour-over opening until water flows from the brew head. When water stops dripping from the brew head, empty the container.
Once the tank is full of water, connect the brewer to electrical power. The heating elements will begin heating the water in the tank. When the water has reached the proper temperature, the “HEAT” light will go out.
IL1618
6
601 p/n 2M-75815 9003, 9010, 9012, 9016 Decanter Coffee Brewer
IMPORTANT:
Tank must be full of
water before connecting
brewer to electrical power.
Heating elements will be
damaged if allowed to
operate without being fully
submerged in water.
Damage caused by
operating the brewer
without water in the tank
is NOT COVERED BY
WARRANTY.
OPERATION (continued)
WATER HEATER
Water temperature is sensed by a
thermobulb inserted into the water tank. This
temperature signal is fed to the thermostat,
which controls line power to the heating
element.
The setpoint temperature is adjustable at the
thermostat.
The element is protected from
over-temperature by a hi-limit thermostat.
IL1619
Fig. 5 Heat Control Diagram
WATER FLOW
601 p/n 2M-75815 9003, 9010, 9012, 9016 Decanter Coffee Brewer
POUR-OVER FEATURE
Pouring any amount of cold water into the
pour-over opening and into the basin pan
forces an identical amount of hot water out
of the tank and through the spray head into
the brew chamber.
AUTOMATIC OPERATION
Pressing BREW button energizes the
solenoid valve, allowing water from an
external water supply to flow into the basin
pan and then into the hot water tank. This
forces an identical amount of hot water out
of the tank and through the spray head into
the brew chamber
The solenoid uses a flow control device so
that flow is consistent between 20 p.s.i. and
90 p.s.i.
Length of time the solenoid is open is
controlled by the timer.
HOT WATER FAUCET
The faucet water coil is submerged in the
hot water tank and draws heat from the brew
water. Water going to the water coil is not
controlled by the solenoid valve.
The faucet is at supply water pressure any
time the faucet shut-off valve is OPEN.
IL1620
Fig. 6 Water Flow Diagram
7
BREWING COFFEE
BURN HAZARD
Exposed surfaces of the
brewer, brew chamber and
decanter may be HOT to
the touch, and can cause
serious burns.
CAUTION:
BURN HAZARD
To avoid splashing or
overflowing hot liquids,
ALWAYS place an empty
decanter under the brew
chamber before starting
the brew cycle. Failure to
comply can cause serious
burns.
CAUTION:
BURN HAZARD
After a brew cycle, brew
chamber contents are
HOT. Remove the brew
chamber and dispose of
used grounds with care.
Failure to comply can
cause serious burns.
NOTE: Water for the hot
water faucet is heated in
a coil inside of the water
tank. Use of the faucet will
not affect the volume of
water delivered for a brew.
However, overuse of the
faucet during a brew may
lower the temperature of
the brew water.
A. PREPARATION
Place one (1) genuine Bloomfield
paper filter in the brew chamber.
Add a pre-measured amount of
fresh coffee grounds.
Gently shake the brew chamber to
level the bed of grounds. Slide the
brew chamber into place under the
brew head.
Fig. 7 Brew Chamber
PAPER
FILTER
BREW
CHAMBER
IL1605
B. POUR-OVER OPERATION
NOTE: Any Integrity™ brewer can be used in the pour-over mode.
BE sure “READY TO BREW” light is lit.
Place the appropriate EMPTY decanter in place under the brew chamber.
Fill a decanter with tap water. Lift the pour-over cover and pour the entire contents of the decanter into the pour-over opening, which will fill the basin.
Water from the basin will displace a like amount of heated water from the tank. The hot water will be forced into the brew head where it will spray over the bed of grounds. Freshly brewed coffee will begin to fill the container under the brew chamber. When the flow and all dripping stops, the coffee is ready to serve.
Discard the contents of the brew chamber. Rinse the brew chamber in a sink. When the ”HEAT” light goes out, the brewer is ready for another brew cycle.
C. AUTOMATIC OPERATION (certain models)
BE sure “READY TO BREW” light is lit.
Place an EMPTY decanter in place under the brew chamber.
Press the “BREW” switch. The solenoid will open for an amount of time determined by the timer setting, admitting a measured quantity of water into the basin.
Water from the basin will displace a like amount of heated water from the tank. The hot water will be forced into the brew head where it will spray over the bed of grounds. Freshly brewed coffee will begin to fill the decanter under the brew chamber. At the end of the brew cycle, plus an amount of time set to allow all water to drip out of the brew chamber, two beeps will sound. When the flow and all dripping stops, the coffee is ready to serve.
Discard the contents of the brew chamber and rinse it in a sink. When the ”READY TO BREW” light comes on, the brewer is ready for another brew cycle.
8
601 p/n 2M-75815 9003, 9010, 9012, 9016 Decanter Coffee Brewer
CAUTION:
CLEANING INSTRUCTIONS
PROCEDURE: Clean Coffee Brewer
CAUTION:
PRECAUTIONS: Disconnect brewer from electric power.
Allow brewer to cool.
FREQUENCY: Daily
TOOLS: Mild Detergent, Clean Soft Cloth or Sponge
Bristle Brush.
Brewing and serving
temperatures of coffee are
extremely hot.
Hot coffee will cause
serious skin burns.
CAUTION:
1. Disconnect brewer from electric power.
Allow brewer to cool before cleaning.
SHOCK HAZARD
Do not submerge or immerse
brewer in water.
2. Remove and empty decanters.
3. Remove and empty brew chamber.
4. Remove the spray disk from the brew head (See figure 8):
BURN HAZARD
Press up on the spray disk ears, then turn the disk to the left to unlatch. Remove the gasket from inside the brew head.
5. Wipe inside of brew head and area around the brew head with a soft clean cloth or sponge moistened with clean water.
IMPORTANT:
DO NOT use steel wool, sharp
objects, or caustic, abrasive or
chlorinated cleansers to clean
the brewer.
601 p/n 2M-75815 9003, 9010, 9012, 9016 Decanter Coffee Brewer
6. Wash the spray disk in a sink using warm water and a mild
detergent. A bristle brush may be used to clear clogged spray holes. Rinse the spray disk with clean water and allow to air dry.
7. Wash the brew chamber in a sink using warm water and a mild detergent. A bristle brush may be used to clean the inside. Rinse with clean water and allow to air dry. For stainless steel brew chambers, be sure the wire rack is properly reinstalled.
GASKET
8. Wipe the exterior of the brewer with a soft clean cloth or sponge moistened with clean water.
10. Reinstall the gasket INSIDE the brew head, then reinstall the spray disk.
11. Reinstall the brew chamber.
12. Decanters may be washed in a dishwasher or sink.
Procedure is complete
9
SPRAY
DISK
LIFT EARS UP
TURN LEFT TO
REMOVE
IL1599
Fig. 8 Cleaning
TROUBLESHOOTING SUGGESTIONS
Water won’t heat
Trips hi-limit safety at start-up
Coffee level low (pour-over)
POSSIBLE CAUSE
Check power supply cord Check /
reset circuit breaker
Thermostat set too low
Set for desired temperature
Hi-Limit thermostat tripped
Allow to cool, Reset hi-limit (8786,
8788)
Damaged internal component or
wiring
Examine wiring & connectors,
thermostat and heating element,
Repair/replace as needed
No Water or too little water added at
start-up
Be sure to add sufficient water prior to
energizing
Not enough water poured in
Increase water amount
Too much coffee grounds
Adjust amount of grounds
Coffee level too high or low (automatic) Timer out of adjustment
Brew chamber overflows
Sprays water from brew head
No brew (automatic)
No flow from hot water faucet
Poor coffee quality
SUGGESTED REMEDY
Brewer unplugged or circuit breaker
tripped
Adjust timer
Too many filter papers or wrong filter
paper
Use one (1) genuine Bloomfield filter
per brew
Brew chamber dispense hole plugged
Thoroughly clean brew chamber
Too much coffee or too fine a grind
Adjust coffee amount and grind
Spray gasket improperly installed
Check/reinstall gasket on INSIDE of
brew head
Spray disk plugged
Clean spray disk
Water supply OFF
Turn water supply ON
Solenoid strainer plugged
Clean strainer
Water filter (if used) plugged
Replace filter element
Bad BREW switch
Replace switch
Damaged internal component or
wiring
Examine wiring & connectors, brew
switch and solenoid Repair/replace as
needed
Faucet valve turned OFF
Turn faucet valve ON
Faucet plugged
Disassemble faucet, clean
Water not hot enough
Adjust water temp 195-205ºF
Keep brewer, airpots and servers clean. Install a taste and odor filter in water
supply, and replace cartridges regularly. Use a quality coffee with a consistent
roast. Use proper grind and amount of coffee per brew.
10
601 p/n 2M-75815 9003, 9010, 9012, 9016 Decanter Coffee Brewer
SYMPTOM
SERVICING INSTRUCTIONS
ACCESS PANELS
CAUTION:
Each warmer plate has a center stud which screws into a bracket.
Warmer plates on Canadian brewers are secured with a nut.
Remove button plug on bottom of brewer to access nut on main
warmer. Remove top panel to access nuts on top warmers.
Remove warmer plates by turning counter-clockwise.
Solenoid door is held by two screws and a retaining lip.
IN-LINE BREWERS:
Top panel is held by two screws at the rear and a retaining lip at
the front. Disconnect wires from the upper warmers.
SHOCK HAZARD
Opening access panels or
removing warmer plates on this
brew may expose uninsulated
electrical components.
Disconnect brewer from
electrical power before
removing any panel or warmer
plate.
Top front panel is held by two screws at the bottom and a
retaining lip at the top.
601 p/n 2M-75815 9003, 9010, 9012, 9016 Decanter Coffee Brewer
Bottom front panel is held by two clips under the warmer plate.
SOLENOID
DOOR
IL1621a
Fig. 9 Access Panels
11
SERVICING INSTRUCTIONS (continued)
TEMPERATURE ADJUSTMENT
Unplug power cord or turn circuit breaker OFF.
Remove top panel.
CAUTION:
SHOCK HAZARD
These procedures involve
exposed electrical circuits.
These procedures are to
be performed by qualified
technical personnel only.
Pull vent tube out of tank lid and insert a thermometer of known
accuracy in vent hole. Reconnect brewer to electrical power.
THERMOSTAT
DIAL-TYPE
THERMOMETER
IN VENT HOLE
ADJUSTING
SHAFT
IL1607
TANK LID
ASSEMBLY
Place an empty decanter under brew chamber. Energize brewer
and pour one decanter (64 oz.) of cold water into
pour-over opening. When READY TO BREW light comes on,
read temperature displayed on thermometer.
Adjust thermostat by turning shaft; clockwise increases
temperature. 1/8 turn = approximately 10ºF.
Refer to Table 1 below for proper brewing temperature based on
altitude.
BOILING
POINT OF
WATER
210
205
NOTE: 1/8 turn = approximately
10ºF (5.6ºC).
IDEAL
BREWING
TEMPERATURE
200
195
MAXIMUM
TEMPERATURE
SETTING
190
ELEVATION (feet above sea level)
97
IDEAL
BREWING
TEMPERATURE
94
91
MAXIMUM
TEMPERATURE
SETTING
0
1,
05
0
1,
20
1, 0
35
0
1,
50
1, 0
65
0
1,
80
1, 0
95
0
0
90
0
75
60
45
0
88
0
15
0
30
0
Fig. 11 Adjust Thermostat
TEMP ( C)
100
IL1606
ELEVATION (meters above sea level)
Table 1
IL1601
BOILING
POINT OF
WATER
IL1602
Boiling Temperature by Altitude
Upon completion, remove thermometer and reinstall vent tube.
12
601 p/n 2M-75815 9003, 9010, 9012, 9016 Decanter Coffee Brewer
IMPORTANT:
A mechanical thermostat will
maintain temperature within
±5ºF. To prevent boiling water
in the brewer, thermostat should
be adjusted to a maximum
temperature equal to the local
boiling temperature minus 5ºF.
Fig. 10 Checking and Adjusting Brew Temperature
TEMP ( F)
NOTE:
Optimum brewing temperature
range is 195ºF to 205ºF (90ºC
to 96ºC).
SERVICING INSTRUCTIONS (continued)
TIMER ADJUSTMENT
The amount of water dispensed automatically during a brew cycle
is controlled by the timer.
Place empty decanter under brew chamber. Press BREW
button. Brewer should dispense one decanter of water. To adjust
amount:
Remove brew chamber and button plug. Adjust knob on timer;
clockwise increases time. Run several cycles to check amount
of water delivered. Replace button plug.
REMOVE TANK LID ASSEMBLY
Unplug brewer or turn circuit breaker OFF. Turn OFF water
supply. Remove top panel. Pull vent tube and inlet elbow out of
basin pan.
Pull water inlet tube out of basin pan. Remove basin pan.
On models with faucet, disconnect inlet pipe at faucet shut-off
valve and outlet pipe at faucet.
IMPORTANT: Water pressure
must be between 20 p.s.i and
90 p.s.i. flowing pressure. If
water pressure exceeds this
value, or if water pressure
varies greatly, a pressure
regulator must be installed in
the water supply line.
IMPORTANT: Before setting assembly into tank, make
sure tank lid gasket is properly
seated on flange of lid.
DO NOT OVER-TIGHTEN.
Disconnect all wiring from thermostat, hi-limit, and heating
element.
Loosen center screw on tank hold-down bracket. Remove
hold-down bracket by sliding short slotted end off of locking stud
and lifting it off. Remove cover assembly by lifting it straight up.
601 p/n 2M-75815 9003, 9010, 9012, 9016 Decanter Coffee Brewer
Reassemble in reverse order.
REPLACE THERMOSTAT
Unplug brewer or turn circuit breaker OFF. Turn OFF water
supply. Remove top panel.
Disconnect all wiring from thermostat only. Loosen and free
jam nut from pass-thru fitting securing temperature sensing bulb.
Remove two screws holding thermostat to bracket.
Lift out thermostat, sensing bulb and thermostat gasket.
Push sensing bulb into tank lid thermowell until fitting seats.
Tighten capillary lock nut only enough to ensure no water
leakage. Excessive tightening is not necessary.
Reassemble in reverse order.
13
IMPORTANT:
If mounting thermostat
p/n WS-8512-51, be sure to
place a new seal washer below
the fitting on the capillary line.
If replacing gray-bodied
thermostat with p/n WS-851251, be sure to remove tube from
thermowell.
SERVICING INSTRUCTIONS (continued)
IMPORTANT: When replacing
heating element, also replace
seal gaskets.
REPLACE HEATING ELEMENT
Remove tank lid assembly as described on page 13.
Remove two hex nuts holding element to cover. Pull element
from mounting holes.
Reassemble in reverse order.
REPLACE SOLENOID
Symptom: Automatic brewer will not flow water; or,
automatic brewer drips continuously from brew head.
NOTE: Wrench p/n 86660 is designed to allow easy removal of
the hoses from the plastic solenoid valve.
IMPORTANT: Shut-off water and electric supply to brewer before
removing hoses or wiring.
Remove water supply flare fitting:
a. Slide the 5/8” end of the wrench over the flats on the inlet fitting of the valve.
b. Hold the wrench to prevent the inlet fitting from turning while installing or removing the inlet water supply flare nut.
Fig. 11
Remove Faucet
Supply from Solenoid
STRAINER
SCREEN
WASHER
WATER INLET
FITTING
Disconnect wiring.
Remove two screws holding solenoid to access door.
Reassemble in reverse order.
CLEAN SOLENOID SCREEN
Symptom: Automatic brewer will not flow water.
Unplug power cord or turn circuit breaker OFF. Turn OFF and
disconnect water supply from brewer inlet fitting.
Unscrew water inlet fitting from solenoid.
IL1608
Fig. 12
Clean Strainer Screen
Using needle-nose pliers, withdraw strainer screen from solenoid.
Clean screen under faucet. A stiff bristle brush may be used if
necessary.
Reinsert screen in solenoid. Be careful to maintain correct
orientation. (The open end of the screen goes in FIRST.)
Reassemble in reverse order.
14
601 p/n 2M-75815 9003, 9010, 9012, 9016 Decanter Coffee Brewer
Remove braided hose:
a. Slide the 7/16” end of the wrench between the valve body and the white ring on the extreme end of the metal hose fitting.
b. Pressure on the white ring toward the metal ferrule releases the clinch ring, allowing the hose to be easily slid off of the solenoid bypass outlet.
c. Install hose on new valve by pressing end of hose onto bypass outlet until it is fully seated.
SERVICING INSTRUCTIONS (continued)
REPLACE TIMER ASSEMBLY
Unplug power cord or turn circuit breaker OFF.
Remove front panel. Remove knob and three screws holding
timer to bracket. Disconnect wiring to timer.
Reassemble in reverse order.
Adjust timer as described on page 13
REPLACE HOT WATER FAUCET COIL
Symptom: Brewer drips continuously from brew head, except
when faucet valve is turned OFF.
Remove tank lid assembly per above.
IMPORTANT: When replacing
water faucet coil, also replace
seal gaskets.
Remove two hex nuts hot water coil to cover. Pull coil from
mounting holes.
Reassemble in reverse order.
REPAIR HOT WATER FAUCET
Remove top panel and turn faucet valve OFF.
Unscrew aerator cap from faucet and remove handle retaining
clip. Do not let faucet body turn.
Pull bonnet assembly from faucet body.
Examine the interior of the faucet body and the surface of the
seat cup. Clean out any debris in the faucet body, using a stiff
bristle brush if necessary.
Examine the aerator. Clean any debris from the screen or flow
straightener, using a stiff bristle brush if necessary.
601 p/n 2M-75815 9003, 9010, 9012, 9016 Decanter Coffee Brewer
Reassemble in reverse order.
REPLACE BREW READY LIGHT or BREW BUTTON
Unplug power cord or turn circuit breaker OFF.
Using Switch Removal Tool (p/n 83209) or a thin screwdriver, pry
light or switch from mounting hole. Disconnect leads.
Reassemble in reverse order.
15
NOTE: Any abrasion or
roughness on the flat end of the
seat cup will require replacing
the seat cup:
Work the seat cup out of the
bonnet and off of the end of the
stem.
Install a new seat cup, making
sure the knob on the stem is
fully inserted into the pocket of
the seat cup, and the skirt of the
seat cup is fully inserted into the
bonnet.
SERVICING INSTRUCTIONS (continued)
CHEMICAL
BURN HAZARD
Deliming chemicals may be
caustic. Wear appropriate
protective gloves and goggles
during this procedure. Never
siphon deliming chemicals
or solutions by mouth. This
operation should only be
performed by qualified and
experienced service personnel.
IMPORTANT: DO NOT spill,
splash or pour water or deliming
solution into or over any internal
component other than the inside
of the water tank.
IMPORTANT: DO NOT allow any internal components
to come into contact with the
deliming solution. Take care to
keep all internal components
dry.
NOTE: Repeat steps 4 thru 5
as required to remove all scale
and lime build-up.
PROCEDURE: Delime the Water Tank
PRECAUTIONS: Disconnect brewer from electric power.
Allow brewer to cool.
FREQUENCY: As required (Brewer slow to heat)
TOOLS: Deliming Solution
Protective Gloves, Goggles & Apron
Mild Detergent, Clean Soft Cloth or Sponge
Bristle Brush, Bottle Brush
Large Sink (or other appropriate work area)
1. Disconnect brewer from the electrical supply. Turn off the water shut-off valve and disconnect the water supply line from the brewer inlet fitting.
2. Remove the tank lid assembly as described on page 13.
3. Remove the water tank from the brewer body by lifting
straight up. Empty all water from the tank. Set the tank back
into the brewer.
4. Mix 2 quarts of deliming solution according to the
manufacturer’s directions. Carefully pour the deliming solution into the water tank. Lower the lid assembly back onto the tank. Allow to sit for 30 minutes, or as directed by the manufacturer.
5. At end of soaking period, remove lid assembly from tank. Thoroughly rinse internal components of lid assembly with clear water. Using a stiff bristle brush, scrub the heating element (and faucet water coil on automatic brewers) to
remove lime and calcium build-up. Rinse with clean water. Store lid assembly in a safe location .
6. Remove the tank from the brewer and empty. Using a stiff bristle brush, scrub the interior of the water tank to remove lime and calcium build-up. Rinse with clean water.
16
601 p/n 2M-75815 9003, 9010, 9012, 9016 Decanter Coffee Brewer
CAUTION:
SERVICING INSTRUCTIONS (continued)
7. Set the tank back into the brewer. Reassemble the tank lid to the water tank. Make sure the gasket is properly in place, then reinstall the hold-down strap.
8. Reinstall wiring to heating element and thermostat. Reinstall the hi-limit thermostat (if removed). For brewers with hot water faucet, reassemble faucet piping. Verify that all internal
components are dry, then reinstall the top panel.
9. Reconnect brewer to electrical supply and, for automatic
brewers, reconnect water supply.
10. Install the brew chamber without filter paper or grounds. Run at least three full brew cycles and discard all water generated.
601 p/n 2M-75815 9003, 9010, 9012, 9016 Decanter Coffee Brewer
11. Brewer is ready to use.
17
NOTE: Normally, silicone hoses
do not need to be delimed.
Should deliming hoses become
necessary, Bloomfield recommends replacing the hoses.
EXPLODED VIEW & PARTS LIST
HOT WATER TANK ASSEMBLY
IL1622
ITEM
PART NO.
13
2C-70134
HOLD-DOWN STRAP
9010, 9012(CA), 9016(EX)
USED ON
14
2C-73457
NUT, HEX 8-32 KEPS
9010, 9012(CA), 9016(EX)
WS-8512-51
THERMOSTAT (BLACK BODY - INCL. SEAL & MOUNTING SCREWS)
WS-86280
THERMO (ALT) (GRAY BODY - INCL. TUBE & MOUNTING SCREWS)
52
2C-70174
SEAL WASHER, THERMO CAP TUBE (ONLY)
9010, 9012(CA), 9016(EX)
54
2I-70147
TANK COVER GASKET
9010, 9012(CA), 9016(EX)
55
2C-70175
NUT HEX 1/2-20 BRASS
9010, 9012(CA), 9016(EX)
56
2I-70152
SEAL GASKET, ELEMENT OR WATER COIL
9010, 9012(CA), 9016(EX)
57
2C-70151
NUT HEX 7/16-20 BRASS
58
2N-70149
HOT WATER COIL
9010, 9012(CA), 9016(EX)
59
2K-70101
TUBE, BASIN OUTLET/TANK INLET, SILICONE
9010, 9012(CA), 9016(EX)
60
2V-70102
TUBE, VENT, SILICONE
9010, 9012(CA), 9016(EX)
61
2K-70103
ELBOW, TANK OUTLET, SILICONE
9010, 9012(CA), 9016(EX)
62
A6-70142
TAN COVER, PLATE ONLY, 8 HOLES
9010, 9012(CA), 9016(EX)
2T-47499
THERMOSTAT, HI-LIMIT
9012(CA)
2T-70716
THERMOSTAT, HI-LIMIT RESET
9010, 9016(EX)
66
2V-70144
WATER INLET TUBE
9010, 9012(CA), 9016(EX)
66a
2C-70146
NUT, HEX 4-40 SS
9010, 9012(CA), 9016(EX)
66b
2C-70146
SCREW 4-40 x 1 PAN HEAD
9010, 9012(CA), 9016(EX)
2N-70167UL
HEATING ELEMENT (120V, 1200W)
9012CA
2N-70143UL
HEATING ELEMENT (120V, 1500W)
9010, 9012
2N-70715UL
HEATING ELEMENT (240V, 3500W)
9016, 9016EX
2N-70173UL
HEATING ELEMENT (240V, 1800W)
230V Units
50
63
67
9010, 9012(CA), 9016(EX)
68
2D-70110
TANK BODY
9010, 9012(CA), 9016(EX)
70
A6-70625
BRACKET, HI LIMIT THERMOSTAT
9010, 9016 (EX)
TANK COVER ASSEMBLY
WS-8541WF-300
INCLUDES: MOUNTED THERMO, HI-LIMIT, 120V 1500W HEATING
ELEMENT & HOT WATER COIL)
18
601 p/n 2M-75815 9003, 9010, 9012, 9016 Decanter Coffee Brewer
DESCRIPTION
EXPLODED VIEW & PARTS LIST (continued)
CABINET PLUMBING COMPONENTS
601 p/n 2M-75815 9003, 9010, 9012, 9016 Decanter Coffee Brewer
IL1623
ITEM
PART NO.
8
2V-70104
FORMED TUBE, FAUCET OUTLET ASSEMBLY 10-7/8” LONG
DESCRIPTION
9010, 9012(CA), 9016(EX)
USED ON
9010, 9012(CA), 9016(EX)
9
2V-70111
FORMED TUBE, FAUCET COIL INLET ASSEMBLY
10
2E-70451
ADAPTER, 1/4” MALE FLARE x 1/8” FPT BRASS
9010, 9012(CA), 9016(EX)
11
2V-70352
VALVE, FAUCET SHUT OFF, NEEDLE SEAT
9010, 9012(CA), 9016(EX)
12
2J-75681
BRAIDED TUBE, FAUCET INLET 6MM x 299MM (11-3/4”) LONG
9010, 9012(CA), 9016(EX)
18
2K-70096
ELBOW, BASIN INLET DIVERTER POLYPROPYLENE
9010, 9012(CA), 9016(EX)
24
2V-70131
TUBE, BREW OUTLET, METAL 4-3/4” LONG
9010, 9012(CA), 9016(EX)
25
2K-70130
ELBOW, SPRAYER, SILICONE
9010, 9012(CA), 9016(EX)
26
2C-72680
LOCK NUT, HEX 7-16-20
9010, 9012(CA), 9016(EX)
27
2C-70107
LOCK WASHER 7/16” EXT SEMS (FAUCET)
9010, 9012(CA), 9016(EX)
28
2C-72681
WASHER, FLAT 15/32” x 1-1/8” x 1/16” SS
9010, 9012(CA), 9016(EX)
29
WS-82556
FAUCET ASSEMBLY, PRESSURE
9010, 9012(CA), 9016(EX)
33
2I-70139
GASKET, SPRAY HEAD
9010, 9012(CA), 9016(EX)
34
A6-72727
SPRAY DISK, EMBOSSED
9010, 9012(CA), 9016(EX)
34a
A6-70163
RETAINER, SPRAY HEAD (REQUIRES DRILL/RIVETS TO INSTALL)
9010, 9012(CA), 9016(EX)
43
A6-70276
TUBE, BASIN INLET, SILICONE 13”
9010, 9012(CA), 9016(EX)
45
2E-75685
2E-74570
SOLENOID W/BYPASS, 120V, .75 GPM
SOLENOID W/BYPASS, 220/240V, .75 GPM
9010, 9012(CA)
9016(EX)
2E-Z16608
SOLENOID BYPASS, 120V .30GPM
9010D3F, 912D3F, 9016D3F
59
2K-70101
TUBE, BASIN OUTLET/TANK INLET, SILICONE
9010, 9012(CA), 9016(EX)
60
2V-70102
TUBE, VENT, SILICONE
9010, 9012(CA), 9016(EX)
61
2K-70103
ELBOW, TANK OUTLET, SILICONE
9010, 9012(CA), 9016(EX)
108
2D-70095
BASIN PAN
9010, 9012(CA), 9016(EX)
WS-82682
FAUCET REPAIR KITS
HANDLE, FAUCET RED (29a)
SEAT CUP (29c)
FAUCET REPAIR KIT, INCL: HANDLE (29a), SEAT CUP (29c),
SPRING (29d), STEM (29h), PIN (29j) & BONNET (29k)
RETAINER CLIP (29b)
WS-84804
AERATOR REPLACEMENT, INCL: O-RING (29e), DISK (29f) & CAP (29g)
WS-84870
AERATOR REPAIR KIT, INCL: O-RING (29e) & DISK (29f)
WS-82573
WS-82575
WS-82576
19
EXPLODED VIEW & PARTS LIST (continued)
ELECTRICAL COMPONENTS
IL1624
2
30
31
32
PART NO.
DESCRIPTION
USED ON
2N-70091UL
HEATING ELEMENT, WARMER 120V 100W
ALL EXCEPT 9016(EX)
2N-70635UL
HEATING ELEMENT, WARMER 220V 85W / 240V 100W
9016(EX)
2E-72946
SWITCH, WARMER ON/OFF 120V
ALL EXCEPT 9016(EX)
2E-70247
SWITCH, WARMER ON/OFF 240V
9016(EX)
2E-70247
SWITCH, WARMER ON/OFF 230V
9003D3, 9012D3 (230V)
2E-70137
SWITCH, MOMENTARY PUSH-BUTTON, BREW
9010, 9012(CA), 9016(EX)
2E-70733
SWITCH ROCKER BREW START
9010, 9012(CA), 9016(EX)
2J-72671
INDICATOR, 120V, READY-TO-BREW
ALL EXCEPT 9016(EX)
2J-70644
INDICATOR, 240V, READY-TO-BREW
9016(EX)
2P-70128
TIMER, 2-MINUTE (WITH DIAL & KNOB) 120V
ALL EXCEPT 9016(EX)
2P-70054
TIMER, 2-MINUTE (WITH DIAL & KNOB) 240V
9016(EX)
2E-70353
POWER CORD ASSEMBLY, 120V NEMA 5-15P
9010, 9012(CA)
A6-71156
CORD & CAP ASSY EURO
9003D3, 9012D3 (230V)
37
2K-70215
STRAIN RELIEF
9010, 9012(CA)
43
2E-70709
TERMINAL BLOCK, 4P
9016(EX)
2E-75685
SOLENOID W/BYPASS, 120V, .75 GPM
9010, 9012(CA)
2E-74570
SOLENOID W/BYPASS, 220/240V, .75 GPM
9016(EX)
35
36
45
50
63
2M-Z16608
SOLENOID BYPASS 120V .30GPM
9010D3F, 9012D3F, 9016D3F
WS-8512-51
THERMOSTAT (BLACK BODY - INCL. SEAL & MOUNTING SCREWS)
9010, 9012(CA), 9016(EX)
WS-86280
THERMO (ALT) (GRAY BODY - INCL. TUBE & MOUNTING SCREWS)
9010, 9012(CA), 9016(EX)
2T-47499
THERMO, HI-LIMIT
9012(CA)
2T-70716
WS-8541-1
67
THERMO, HI-LIMIT, RESET
9010, 9016(EX)
HEATING ELEMENT, WATER TANK 120V 2000W
9010, 9012(CA)
2N-70143UL
HEATING ELEMENT, WATER TANK 120V 1500W
9012CA
2N-70715UL
HEATING ELEMENT, WATER TANK 240V 3500W
9016(EX)
2N-70173UL
HEATING ELEMENT, WATER TANK, 240V 1800W
9003D3, 9012D3 (230V)
SOLENOID REPAIR KITS
WS-85218
SOLENOID REPAIR KITS: INLET FITTING KIT INCLUDES: CAP (45a),
FITTING (45b), GASKET (45c) & STRAINER (45d)
WS-85219
SOLENOID REPAIR KITS: INLET STRAINER ( 45d ONLY)
20
IL1612
601 p/n 2M-75815 9003, 9010, 9012, 9016 Decanter Coffee Brewer
ITEM
EXPLODED VIEW & PARTS LIST (continued)
CABINET COMPONENTS
IL1625
ITEM PART NO. DESCRIPTION
2D-70090
COVER PLATE, WARMER BLACK, 1/4-28 STUD
9010, 9012(CA), 9016(EX),
UNITS MADE IN USA
2D-Z15630
PLATE COVER WARMER, 1/4-20 STUD
9010, 9012(CA), 9016(EX),
UNITS MADE IN CHINA
33
2I-70139
GASKET, SPRAY HEAD
9010, 9012(CA), 9016(EX)
34
A6-72727
SPRAY DISK, EMBOSSED
9010, 9012(CA), 9016(EX)
34a
A6-70163
RETAINER, SPRAY HEAD (REQUIRES DRILL/RIVETS TO INSTALL)
9010, 9012(CA), 9016(EX)
70
2P-70053
BUTTON PLUG, 2”, METAL
9010, 9012(CA), 9016(EX)
73
2A-71732
LEG ASSEMBLY, LEVELLING
9010, 9012(CA), 9016(EX)
75
2K-70229
BUSHING, HEYCO
9010, 9012(CA), 9016(EX)
104
2Q-75089
DOOR, SOLENOID ACCESS, PLASTIC
9010, 9012(CA), 9016(EX)
105
2F-76666
POUR OVER ASSEMBLY, PLASTIC
9010, 9012(CA), 9016(EX)
107
A6-70089
SPLASH GUARD, POUR-OVER
9010, 9012(CA), 9016(EX)
108
2D-70095
BASIN PAN
9010, 9012(CA), 9016(EX)
109
2M-70200
DECAL 9003, 12, 16 BASIN
9010D, 9012D, 9016D
WS-9012-11
BODY & BASE ASSEMBLY
9010, 9012(CA), 9016
3
601 p/n 2M-75815 9003, 9010, 9012, 9016 Decanter Coffee Brewer
USED ON
121
DD-9016-211 BODY & BASE ASSEMBLY, EXPORT
9016(EX)
122
A6-70100
PANEL, UPPER FRONT
9010, 9012(CA), 9016(EX)
123
A6-70097
PANEL, LOWER FRONT
9010, 9012(CA), 9016(EX)
124
A6-70117
BOTTOM PLATE
9010, 9012(CA), 9016(EX)
125
2C-70098
CLIP, MOUNTING
9010, 9012(CA), 9016(EX)
126
WS-9012-10
BASIN COVER W/ 2 WARMER PLATE MOUNTS
9010, 9012(CA), 9016(EX)
2D-70234
BREW CHAMBER, BLACK PLASTIC
9010, 9012(CA), 9016(EX)
WS-8942-6
BREW CHAMBER, BROWN PLASTIC (OPTIONAL limited to stock on hand)
2D-70114
BREW CHAMBER, STAINLESS W/ WIRE BASKET (OPTIONAL)
WS-POF
FILTER PAPER, COFFEE (CASE OF 1000)
200
201
21
9010, 9012(CA), 9016(EX)
22
K
AC
BL
GE
AN
LK
LU
E
6B
7B
HT
TANK CVR HARNESS
PN 70455
ITE
WH
K
AC
BL
OR
AC
K
BL
MAIN WIRE HARNESS
PN 70448
9W
9
1
4
0
P1
CK
LA
45
70
7B
E
LU
6B
TE
HI
3W
E
E
HIT
NG
RA
1O
CK
9W
LA
7B
OR
CT
3
NE
2
5R
ED
N
CO
ED
5R
CK
LA
7B
T
WH
CK
LA
7B
3
1
3W
E
HIT
OR
CT
E
NN
CO
2
C3
E
NG
RA
8O
L
4B
E
NG
RA
1O
K
AC
E
4
3
WN
K
22
3W
HI
TE
C1
ITE
WH
OR
CT
1
NE
2
CK
N
CO
AC
L
7B
HIT
3W
52
4
70
E
NG
RO
2B
LA
7B
LOWER WARMER
ELEMENT
8O
RA
TE
HI
3W
E
NG
RA
1O
WIRING DIAGRAM
601 p/n 2M-75815 9003, 9010, 9012, 9016 Decanter Coffee Brewer
TANK HEATING
ELEMENT
CONTROL
THERMOSTAT
UPPER REAR
WARMER SWITCH
UPPER FRONT
WARMER SWITCH
LOWER WARMER
SWITCH
PILOT LIGHT
E
HIT
3W
3W
HIT
4B
E
LA
2B
CK
RO
WN
0
INE
45
70
L
TO
1
ANG. O
- 1+
MATERIAL
NONE
SCALE
9003
SMC
DWN.
DIAGRAM WIRE
UNLESS NOTED
USED ON
PART NAME
WAS
TOL.
DEC.
.0 -+=.030
.00 -+=.020
.000-+ =.005
2
3
3
P
OR
CT
E
NN
CO
1
ITE
DK
ENG.
REVISIONS
GC
CKD.
BY
1
*
2M-77311
PART NO.
St. Louis, MO
BLOOMFIELD
WELLS
DATE
7/11/05
(-)
OF
1
77311
ISSUE
SH.
APP
SMC DK
UPPER REAR
WARMER
ELEMENT
UP-WARMER HARNESS
PN 70459
D
UE
BL
WH
ENG. REL. ECN-12898
DO NOT SCALE DWG.
ISSUE
(-)
2
2
RC
TO
EC
N
N
O
C
3
RD
CO
RE
UPPER FRONT
WARMER ELEMENT
WIRING DIAGRAMS 9003
601 p/n 2M-75815 9003, 9010, 9012, 9016 Decanter Coffee Brewer
WIRING DIAGRAMS 9010
23
601 p/n 2M-75815 9003, 9010, 9012, 9016 Decanter Coffee Brewer
WIRING DIAGRAMS 9016
24
601 p/n 2M-75815 9003, 9010, 9012, 9016 Decanter Coffee Brewer
NOTES
25
10 Sunnen Drive, St. Louis, MO 63143
telephone: 314-678-6336 fax: 314-781-2714
www.bloomfieldworldwide.com