Draytek | P2261 | VigorSwitch P2261 PoE 24+2 Giga Port L2 Managed Switch Quick

VigorSwitch P2261
PoE 24+2 Giga Port
L2 Managed Switch
Quick Start Guide
European Community Declarations
Manufacturer: DrayTek Corp.
Address:
No. 26, Fu Shing Road, HuKou Township, HsinChu Industrial
Park, Hsin-Chu, Taiwan 303
Product:
VigorSwitch P2261
DrayTek Corp. declares that VigorSwitch P2261 is in compliance with the
following essential requirements and other relevant provisions of 2004/108/EC.
The product conforms to the requirements of Electro-Magnetic Compatibility
(EMC) Directive 2004/108/EC by complying with the requirements set forth in
EN55022/Class A and EN55024/Class A.
The product conforms to the requirements of Low Voltage (LVD) Directive
2006/95/EC by complying with the requirements set forth in EN60950-1.
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a class
A computing device pursuant to Subpart J of part 15 of FCC Rules, which are
designed to provide reasonable protection against such interference when
operated in a commercial environment.
Version: 1.01
Date: 08/11/2012
 Package Content
The 24+2 Giga Port L2 Managed Switch is a standard switch that meets all
IEEE 802.3/u/x/z Gigabit, Fast Ethernet specifications. It is a switch with 24
10/100/1000Mbps TP (20-Port for TP; 4-Port for Combo) and 2-Port
Dual-SFP Fiber management Ethernet ports.
The network administrator can logon the switch to monitor, configure and
control each port’s activity. In addition, the switch implements the QoS
(Quality of Service), VLAN, and Trunking. It is suitable for office
application.
VigorSwitch
Rack Mount Kit
CD
Ethernet Cable
EU-type power cord
Note: If any of these items is found missing or damaged, please contact
your local supplier for replacement.
 Descriptions of Panel
LED Explanation
LED
Color
POWER
Green
Lit when +3.3V power is coming up.
Green
Lit when connection with remote device is good.
Blinks when any traffic is present.
Green
Lit Green when PoE device is up.
Off when PoE device is down
TP Port 1– 24
(RJ45 LEFT)
LINK/ACT
TP Port 1– 24
(RJ45 RIGHT)
For PoE model
SFP Port 21-24
LINK/ACT
SFP Port 25-26
LINK/ACT
Green/
Amber
Green/
Amber
Explanation
Lit Green when TP connection with remote device is
1000M..
Lit Amber when TP connection with remote device is
100M.
Blinks when any traffic is present.
Lit Green when the connection with remote device is
1000M.
Lit Amber when the connection with remote device is
100M.
Blinks when any traffic is present.
Connector Explanation
Interface
RESET
Description
Used to restart the device to default settings.
CONSOLE
Used to perform telnet command control.
LAN P1 – P24
Giga Ethernet Port.
SFP (21 – 26)
SFP Fiber Port.
 Installing Your Switch
A hierarchical network with minimum levels of switch may reduce the timing
delay between server and client station. Basically, with this approach, it will
minimize the number of switches in any one path; will lower the possibility of
network loop and will improve network efficiency. If more than two switches
are connected in the same network, select one switch as Level 1 switch and
connect all other switches to it at Level 2. Server/Host is recommended to
connect to the Level 1 switch. This is general if no VLAN or other special
requirements are applied.
The connection among IP Phone, Access Point and VigorSwitch
Each port can support 30.8W power; the total power supply can reach to 185W.
For other examples of hardware installation, please refer to User’s Guide for
detailed information.
Download PDF