Odyssey Tipping Bucket Rain Gauge Logger User Manual

Odyssey Tipping Bucket Rain Gauge Logger.
Contents.
Introduction. ....................................................................................................................2
Installation & Testing. ......................................................................................................2
Calibration.......................................................................................................................3
Alternative Method of Calibration. ................................................................................3
Memory Storage Capacity. ..............................................................................................5
Dataflow Systems PTY Ltd
Introduction.
The Odyssey tipping bucket rain gauge logger is designed to interface with a Davis
Tipping Bucket or other compatible model (please check with the manufacturer). This
logger records the time of each bucket tip generating true rainfall intensity data.
Installation & Testing.
The rain gauge installation details are included in the DAVIS Rain Collector handbook.
The recorder and tipping bucket must first be tested to ensure that the system is
working.
Remove the cable tie holding the tipping buckets in the shipping position.
Using the Odyssey software click on the PROBE TRACE MODE icon and select the
TIPPING BUCKET RAIN GAUGE sensor from the sensor option list.
Gently tip the rain gauge bucket until it drops to the opposite side. The recorder will
detect the bucket tips and send the data to the computer each time you tip the bucket.
The tipping time will be displayed on the computer screen.
Dataflow Systems PTY Ltd
Calibration.
The orifice of the rain gauge is 6.5 inches or 165.1 millimeters. Before calibrating the
rain gauge makes sure the bucket surfaces are clean.
The standard calibration is in millimeters. The Davis tipping bucket may be set up in
imperial or metric measurements. Ensure that the metric measurement adaptor has
been fitted. Instructions are in the Davis manual supplied with the rain gauge.
Open the Tipping Bucket Rain Gauge calibration file in the Odyssey software.
Measurement units are in mm. Enter the following data in the calibration table.
First Value
Second Value
Relative Value
No. Decimal places
Un-calibrated Value
0
233
0
Measured Value
0
46.6
Finally, save the calibration file.
The Davis Tipping Bucket Rain Gauge is factory calibrated and should not normally
require any attention other than keeping it clean. The mechanical adjustments should
not have to be altered. If the calibration appears to be significantly in error, put a
calibrated rain gauge of at least 100 mm diameter within 600 mm of the one under test
and compare the readings over a period of time. A significant rainfall event will give the
best results.
Calculate the number of tips by first downloading the logged data and then editing the
site data and recording the number of scans.
Each scan represents one tip. The column R.G.Tip also shows each tip. Enter the
number of tips in the un-calibrated column and the rainfall measurement in the
measured value column of the Calibration File.
Alternative Method of Calibration.
The following method of calibration may be used; however its accuracy leaves much to
be desired as the drip rate can sometimes flood the buckets giving far fewer tips than
what is expected.
A plastic container big enough to hold one litre of water is required to carry out a
calibration. The container should have a 1mm hole drilled in the bottom of the container
at the lowest point, if the base of the container is not flat.
Dataflow Systems PTY Ltd
A site file must be set up before the calibration can be started. Refer Odyssey Data
Logging Software manual to set up a site file.
To carry out the calibration the recorder must be started. Refer ‘Set up and Start Logger’
section of Odyssey Data Logging Software manual.
Unplug the serial cable from the logger and screw the cap back on.
Place the rain gauge onto an area where the water that drains from the gauge will not
cause a problem. Place the water container into the cone and tip 1 litre of water into the
container. The bucket should start tipping within a few seconds. The tip rate should be
approximately one tip every five seconds.
The calculation to determine the number of tips is as follows:
• Radius = 8.255 cm
• Area of rain gauge orifice = Pi * 8.255^ 2 = 214.08 square cm
• 1 mm of rain = 21.408 cc of water
• The number of bucket tips per 1 cm of rain = 10 mm/0.2 mm = 50
The number of bucket tips for 1 litre of water, if the rains gauge calibration is perfect,
should be:
(1000/214.08) x 50 = 233
Each bucket tip should be 0.2 mm of rain so that the calibration rainfall
value is
233 x 0.2 = 46.6 mm
When all the water from the container has emptied into the rain gauge, the recorder
must be down loaded into your computer. Plug the serial cable into the Odyssey
recorder and click on ‘Stop Logger and Save Data’. Then select the site that was used
to set up the recorder for the calibration.
When the data has been loaded, click on Data Worksheet. The recorded data will now
be displayed on the screen. The number of scans counted in the left hand column
represents the number of bucket tips. Enter this value into the UN-CALIBRATED second
value of the calibration file, and 46.6 into the MEASURED second value. Now enter 0 for
the first reading in both the UN-CALIBRATED VALUE and the MEASURED VALUE in
the calibration file. Finally, save the calibration file.
Dataflow Systems PTY Ltd
Memory Storage Capacity.
The logger records the current time of day every time the bucket tips. This is stored as a
three-byte number. At midnight every day a midnight flag is recorded. A 0.2mm rain
gauge would record approximately 21500-bucket tips, which is 4300 millimeters of rain.
When the memory is full the recorder shuts down.
Dataflow Systems PTY Ltd