DFI | KS200 | User`s manual | DFI KS200 User`s manual

KS200/201/202
Touch Panel PC
User’s Manual
A23200228
1
Chapter 1 Introduction
www.dfi.com
Copyright
FCC and DOC Statement on Class B
This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without
the prior written permission from the copyright holders.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any particular
purpose. The user will assume the entire risk of the use or the results of the use of this document. Further, the manufacturer reserves the right to revise this publication and make changes
to its contents at any time, without obligation to notify any person or entity of such revisions
or changes.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio TV technician for help.
© 2012. All Rights Reserved.
Trademarks
Notice:
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
1.
2.
The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Shielded interface cables must be used in order to comply with the emission limits.
2
Chapter 1 Introduction
www.dfi.com
Table of Contents
Copyright�������������������������������������������������������������������������������������������������������������2
Trademarks��������������������������������������������������������������������������������������������������������2
FCC and DOC Statement on Class B����������������������������������������������������� 2
About this Manual������������������������������������������������������������������������������������������4
Warranty��������������������������������������������������������������������������������������������������������������4
Static Electricity Precautions����������������������������������������������������������������������4
Safety Measures����������������������������������������������������������������������������������������������4
About the Package�����������������������������������������������������������������������������������������5
Chapter 1 - Introduction�����������������������������������������������������������������������������6
Overview ........................................................................................................6
Key Features .................................................................................................7
Specifications ................................................................................................8
Getting the Know the KS200/201/202 ................................................ 11
Mechanical Dimensions ............................................................................ 12
Chapter 2 - Installation���������������������������������������������������������������� 14
Connecting Cables to Terminal Blocks
................................................ 14
Chapter 3 - Ports and Connectors���������������������������������������������� 15
Top Panel I/O Port .................................................................................... 15
Bottom Panel I/O Ports ........................................................................... 16
Chapter 4 - Mounting Options
�������������������������������������������������������������� 20
Wall Mount .................................................................................................. 20
Panel Mount ................................................................................................ 21
3
Chapter 1 Introduction
www.dfi.com
About this Manual
Static Electricity Precautions
An electronic file of this manual is included in the CD. To view the user’s manual in the CD, insert the CD into a CD-ROM drive. The autorun screen (Main Board Utility CD) will appear. Click
“User’s Manual” on the main menu.
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in handling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are
ready to install it.
Warranty
1.
2.
The warranty is void if the product has been subjected to physical abuse, improper installation, modification, accidents or unauthorized repair of the product.
3.
Unless otherwise instructed in this user’s manual, the user may not, under any circumstances, attempt to perform service, adjustments or repairs on the product, whether in or
out of warranty. It must be returned to the purchase point, factory or authorized service
agency for all such work.
4.
2. Wear an antistatic wrist strap.
Warranty does not cover damages or failures that arised from misuse of the product,
inability to use the product, unauthorized replacement or alteration of components and
product specifications.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, contacts
or connections.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or con
nectors by their ends.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other components.
Perform the upgrade instruction procedures described at an ESD workstation only. If such a station is not available, you can provide some ESD protection by wearing an antistatic wrist strap
and attaching it to a metal part of the system chassis. If a wrist strap is unavailable, establish
and maintain contact with the system chassis throughout any procedures requiring ESD protection.
We will not be liable for any indirect, special, incidental or consequencial damages to the
product that has been modified or altered.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power cord.
Battery:
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
4
Chapter 1 Introduction
www.dfi.com
Safety Precautions
About the Package
• Use the correct DC input voltage range.
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
• Unplug the power cord before removing the system chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power cord.
• 1
• 1
• 3
• 1
• 1
• 1
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
Touch Panel PC
Poron foam
Terminal blocks
19V Power adapter
CD disk includes: Manual
Quick Installation Guide
Optional Items
• Keep this system away from humidity.
• Wall Mount kit
• Panel Mount kit
• Power Cord
• Place the system on a stable surface. Dropping it or letting it fall may cause damage.
• The openings on the system are for air ventilation to protect the system from overheating.
DO NOT COVER THE OPENINGS.
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance to the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
• Place the power cord in such a way that it will not be stepped on. Do not place anything on
top of the power cord. Use a power cord that has been approved for use with the system
and that it matches the voltage and current marked on the system’s electrical range label.
• If the system will not be used for a long time, disconnect it from the power source to avoid
damage by transient overvoltage.
• If one of the following occurs, consult a service personnel:
- The power cord or plug is damaged.
- Liquid has penetrated the system.
- The system has been exposed to moisture.
- The system is not working properly.
- The system dropped or is damaged.
- The system has obvious signs of breakage.
• The unit uses a three-wire ground cable which is equipped with a third pin to ground the
unit and prevent electric shock. Do not defeat the purpose of this pin. If your outlet does
not support this kind of plug, contact your electrician to replace the outlet.
• Disconnect the system from the DC outlet before cleaning. Use a damp cloth. Do not use
liquid or spray detergents for cleaning.
5
Chapter 1 Introduction
www.dfi.com
Chapter 1
Chapter 1 - Introduction
Overview
KS200
KS201
6
Chapter 1 Introduction
www.dfi.com
Chapter 1
KS202
Key Features
•
•
•
•
TI® AM3517 Sitara ARM Cortex-A8
7" WVGA Touch Screen Fanless Panel PC
512MB DDR2 onboard
512MB NAND Flash onboard
KS200
SD/MMC
1 SD/MMC card socket
LAN
1 COM port
COM
2 COM ports
USB
2 Type A USB 2.0/1.1 ports
GPIO
12-bit GPIO connector
KS201
KS202
4 Customizable function keys
Open Frame
7
Chapter 1 Introduction
www.dfi.com
Chapter 1
Specifications
KS200
Processor System
I/O Ports
• TI® AM3517 Sitara ARM Cortex-A8
Memory
• 512MB DDR2 onboard
- 4 DDR2 64Mx16 RAM
LCD and
Touch Screen
•7” (800x480) WVGA TFT touch screen LCD
• Supports touch screen
- TI® TSC2004 touch screen controller
• 400 NITS
• 4-Wire Resistive type
Storage
•1 SD/MMC card socket
• 512MB NAND Flash
- Samsung K9F4G08U0D flash memory 512Mx 8bit (512MB)
•Front
- 1 Power LED
• Top
- 1 SD/MMC card socket
• Bottom
- 12-bit GPIO (2 7-pole terminal blocks)
- 1 Line-out
- 1 DB-9 RS232 COM
- 1 RJ45 10/100Mbps LAN with LEDs
- 2 USB 2.0 (Type A)
- 1 DB-9 RS232/422/485 COM
- 1 DC-in (2-pole Phoenix terminal block)
- 1 power switch
•LAN8710 10/100Mbps LAN chip
• 1 LAN port
• Supports 10BASE-T and 100BASE-T
Front Panel
Protection
•IP65 (Dust Tight; Water Proof protection)
Audio
•1 Line-out
Construction
•Aluminum front bezel, Rugged metal housing
COM
•1 RS232/422/485 COM port
• 1 RS232 COM port
Mounting
•Wall mount (VESA 75x75)
USB
•1 TUSB1210 USB transceiver
• 2 Type A USB 2.0/1.1 ports
Dimensions
•235mm x 150mm x 40.8mm (W x H x D)
GPIO
• 12-bit GPIO connector
Weight
•2.10 kg
Power
• Power input voltage
- 14~30Vdc (+/-5%) input
OS Support
•Windows CE 6.0
• Linux 2.6.x
Environment
• Temperature
- Operating: -20oC ~ 65oC
- Storage: -30oC ~ 80oC
• Relative Humidity
- 95% RH at 65oC, 1 week
• Corrosion
- 4 periods of 7 days at 65oC with 90-95% relative humidity after 2 hours salt
spray or waiver
Certification
• CE
• FCC Class B
• Compliant with IEC 60945 (Protected B)
Ethernet
•Panel mount (Mounting clamp)
8
Chapter 1 Introduction
www.dfi.com
Chapter 1
Specifications
KS201
Processor System
Memory
• 512MB DDR2 onboard
- 4 DDR2 64Mx16 RAM
LCD and
Touch Screen
•7” (800x480) WVGA TFT touch screen LCD
• Supports touch screen
- TI® TSC2004 touch screen controller
• 400 NITS
• 4-Wire Resistive type
Storage
•1 SD/MMC card socket
• 512MB NAND Flash
- Samsung K9F4G08U0D flash memory 512Mx 8bit (512MB)
Ethernet
I/O Ports
• TI® AM3517 Sitara ARM Cortex-A8
•LAN8710 10/100Mbps LAN chip
• 1 LAN port
• Supports 10BASE-T and 100BASE-T
Audio
•1 Line-out
COM
•1 RS232/422/485 COM port
• 1 RS232 COM port
USB
•1 TUSB1210 USB transceiver
• 2 Type A USB 2.0/1.1 ports
GPIO
• 12-bit GPIO connector
Power
• Power input voltage
- 14~30Vdc (+/-5%) input
Environment
• Temperature
- Operating: -20oC ~ 65oC
- Storage: -30oC ~ 80oC
• Relative Humidity
- 95% RH at 65oC, 1 week
• Corrosion
- 4 periods of 7 days at 65oC with 90-95% relative humidity after 2 hours salt
spray or waiver
•Front
- 1 Power LED
- 4 Function keys
• Top
- 1 SD/MMC card socket
• Bottom
- 12-bit GPIO (2 7-pole terminal blocks)
- 1 Line-out
- 1 DB-9 RS232 COM
- 1 RJ45 10/100Mbps LAN with LEDs
- 2 USB 2.0 (Type A)
- 1 DB-9 RS232/422/485 COM
- 1 DC-in (2-pole Phoenix terminal block)
- 1 power switch
Front Panel
Protection
•IP65 (Dust Tight; Water Proof protection)
Construction
•Aluminum front bezel, Rugged metal housing
Mounting
•Wall mount (VESA 75x75)
•Panel mount (Mounting clamp)
Dimensions
•235mm x 150mm x 40.8mm (W x H x D)
Weight
•2.10 kg
OS Support
•Windows CE 6.0
• Android 2.1
• Linux 2.6.x
Certification
• CE
• FCC Class B
• Compliant with IEC 60945 (Protected B)
9
Chapter 1 Introduction
www.dfi.com
Chapter 1
Specifications
KS202
Processor System
I/O Ports
• TI® AM3517 Sitara ARM Cortex-A8
Memory
• 512MB DDR2 onboard
- 4 DDR2 64Mx16 RAM
LCD and
Touch Screen
•7” (800x480) WVGA TFT touch screen LCD
• Supports touch screen
- TI® TSC2004 touch screen controller
• 400 NITS
• 4-Wire Resistive type
Storage
•1 SD/MMC card socket
• 512MB NAND Flash
- Samsung K9F4G08U0D flash memory 512Mx 8bit (512MB)
•Front
- 1 Power LED
• Top
- 1 SD/MMC card socket
• Bottom
- 12-bit GPIO (2 7-pole terminal blocks)
- 1 Line-out
- 1 DB-9 RS232 COM
- 1 RJ45 10/100Mbps LAN with LEDs
- 2 USB 2.0 (Type A)
- 1 DB-9 RS232/422/485 COM
- 1 DC-in (2-pole Phoenix terminal block)
- 1 power switch
•LAN8710 10/100Mbps LAN chip
• 1 LAN port
• Supports 10BASE-T and 100BASE-T
Front Panel
Protection
•IP65 (Dust Tight; Water Proof protection)
Audio
•1 Line-out
Construction
•Aluminum front bezel, Rugged metal housing
COM
•1 RS232/422/485 COM port
• 1 RS232 COM port
Mounting
•VESA 75x75
Dimensions
•230.40mm x 142.32mm x 35.8mm (W x H x D)
Weight
•1.90 kg
OS Support
•Windows CE 6.0
• Android 2.1
• Linux 2.6.x
Certification
• CE
• FCC Class B
• Compliant with IEC 60945 (Protected B)
Ethernet
USB
•1 TUSB1210 USB transceiver
• 2 Type A USB 2.0/1.1 ports
GPIO
• 12-bit GPIO connector
Power
• Power input voltage
- 14~30Vdc (+/-5%) input
Environment
• Temperature
- Operating: -20oC ~ 65oC
- Storage: -30oC ~ 80oC
• Relative Humidity
- 95% RH at 65oC, 1 week
• Corrosion
- 4 periods of 7 days at 65oC with 90-95% relative humidity after 2 hours salt
spray or waiver
10
Chapter 1 Introduction
www.dfi.com
Chapter 1
Getting to Know the KS200/201/202
Front View
Bottom View
RS232 COM
Function Keys
Line-Out
12-bit GPIO
USB
LAN
14-30V DC-in
Power Switch
RS232/422/485 COM
COM Ports
Used to connect serial devices.
Power LED
USB Ports
Used to connect USB 2.0/1.1 devices.
Power LED
Indicates the power status of the system.
LAN Port
Used to connect the system to a local area network.
Function Keys (KS201)
Used to navigate through the pages.
GPIO
Supports 12-bit digital output and input.
Line-out
Used to connect to a speaker.
Top View
DC-in
Used to plug a power adapter.
SD/MMC
SD/MMC
Indicates to insert and SD and MMC.
11
Chapter 1 Introduction
www.dfi.com
Chapter 1
Mechanical Dimensions
KS200
KS201
214.60
214.60
Top View
Top View
Left View
150.00
150.00
235.00
Right View
235.00
Left View
Front View
40.80
Front View
Right View
40.80
Bottom View
Bottom View
12
Chapter 1 Introduction
www.dfi.com
Chapter 1
KS202
214.60
Top View
Left View
95.00
90.00
190.00
Front View
11.20
35.80
75.00
75.00
93.40 (V,A FOR T/P)
133.00
90.00
20.99
4.49
142.32
65.85
20.20
92.04 (A,A FOR T/P)
Ø3.50
125.60
230.40
221.00
190.00
154.40 (V,A FOR T/P)
153.00 (A,A FOR T/P)
Right View
20.20
Bottom View
13
Chapter 1 Introduction
www.dfi.com
Chapter 2
Chapter 2 - Installation
2. Plug the terminal block into the DC-in connector and then tighten the screws to secure the
terminal block in place.
Connecting Cables to Terminal Blocks
Important:
DC-in
connector
When installing the touch panel PC, make sure the power is off. Failure to turn off, may cause
severe damage to the system.
Screws
1. Insert the cable end of the power adaptor to the terminal block. To firmly fix the cable into
the terminal block, use a screwdriver to clamp down the wires to the screw that is in the
terminal block.
Terminal block
+
Wire
White Wire
-
Black Wire
Power adapter cable
14
Chapter 2 Installation
www.dfi.com
Chapter 3
Chapter 3 - Ports and Connectors
SD/MMC
Top Panel I/O Port
SD/MMC
The front panel I/O port consist of the following:
SD/MMC
• 1 SD/MMC slot
This expansion port is used to insert a Secure Digital (SD) or Multimedia Card (MMC) device.
Aside from storing data files, an SD card is also capable of storing powerful software applications.
15
Chapter 3 Ports and Connectors
www.dfi.com
Chapter 3
GPIO
Bottom Panel I/O Ports
RS232 COM
Line-Out
12-bit GPIO
USB
LAN
14-30V DC-in
Power Switch
RS232/422/485 COM
8
14
1
7
The bottom panel I/O ports consist of the following:
•
•
•
•
•
•
1
1
1
1
1
2
12-bit GPIO
Line-Out jack
RS232 COM port
RS232/422/485 COM port
LAN port
USB ports
The Digital I/O connector provides powering-on function to an external device that is connected to this connector.
Pin
Pin Assignment
Pin
Pin Assignment
1
GPIO-OUT1
8
GPIO-IN1
2
GPIO-OUT2
9
GPIO-IN2
3
GPIO-OUT3
10
GPIO-IN3
4
GPIO-OUT4
11
GPIO-IN4
5
GPIO-OUT5
12
GPIO-IN5
6
GPIO-OUT6
13
GPIO-IN6
7
5V_VCC
14
GND
16
Chapter 3 Ports and Connectors
www.dfi.com
Chapter 3
RS232 COM 1
Line-out
COM 1: RS232
This jack is used to connect a headphone or external speakers.
DCD
RXD
TXD
DTR
GND
COM 1 is fixed at RS232.
12345
DSR
RTS
CTS
RI
6 7 8 9
17
Chapter 3 Ports and Connectors
www.dfi.com
Chapter 3
RS232/422/485 COM 2
LAN Port
COM 2:
RS232/422/485
The LAN port allows the system board to connect to a local area network by means of a network hub.
6789
DATA+
DATAN.C.
N.C.
GND
6789
N.C.
N.C.
N.C.
N.C.
1 2 34 5
DSR
RTS
CTS
RI
1 2 34 5
12 345
6789
N.C.
N.C.
N.C.
N.C.
RX+
RXTX+
TXGND
DCD
RXD
TXD
DTR
GND
COM 2
18
Chapter 3 Ports and Connectors
www.dfi.com
Chapter 3
USB Ports
USB 1-2
USB allows data exchange between your computer and a wide range of simultaneously accessible external Plug and Play peripherals.
The system board is equipped with two onboard USB 2.0/1.1 ports (USB 1-2).
19
Chapter 3 Ports and Connectors
www.dfi.com
Chapter 4
Chapter 4 - Mounting Options
3. Attach the other bracket (wall mount bracket 2) to the rear of the Panel PC.
Wall Mount
The wall mount kit includes the following:
Mounting screw
•
•
Wall mount bracket 2
2 Wall mount brackets
Bracket screws
Hooks
4. Using the hooks on “bracket 2”, slide the Panel PC to “bracket 1”.
Wall mount bracket 1
Wall mount bracket 2
Wall mount bracket 2
1.
Select a place on the wall where you will mount the Panel PC.
2.
Use the provided mounting screws to attach “wall mount bracket 1” to the wall.
Wall mount bracket 1
Mounting screw
5. Tighten the screw to hold the assembly in place.
Wall mount bracket 1
Mounting screw
20
Chapter 4 Mounting Options
www.dfi.com
Panel Mount
The panel mounting kit includes the following:
• 6 mounting clamps
1.
Select a place on the panel where you will mount the Panel PC.
2.
Cut out a shape on the panel that corresponds to the Panel PC’s rear dimensions
(217.6mm x 128.6mm).
128.60
21
7.6
0
3. Stick the poron foam on the rear panel.
Poron foam
Poron foam
21
Chapter 4 Mounting Options
www.dfi.com
Chapter 4
4. Slide the Panel PC through the hole until it is properly fitted against the panel.
5. Position the mounting clamps along the rear edges of the Panel PC, fitting them into the slits
that are around the Panel PC.
Mounting
clamp
128.60
Slit for mounting
the clamp
21
7.6
0
White plastic
cap
6. The first and second clamps must be positioned and secured diagonally prior to mounting the
rest of the clamps. Tighten the clamp’s screw using an electric screwdriver until the white
plastic cap touches the panel. Do not over tighten the screws to prevent damaging the Panel
PC. The illustration below shows all clamps properly mounted.
Panel wall
22
Chapter 4 Mounting Options
www.dfi.com
Download PDF