Woodstock SHOP FOX D3274 Instruction manual

MODEL D3274
GRAVITY FEED SPRAY
GUN W/REGULATOR
OWNER'S MANUAL
Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz
COPYRIGHT © JULY, 2008 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#10833JM PRINTED IN CHINA
K_`jdXelXcgifm`[\jZi`k`ZXcjX]\kp`ejkilZk`fejfek_\gifg\ij\klg#
fg\iXk`fe#dX`ek\eXeZ\Xe[j\im`Z\f]k_`jdXZ_`e\&\hl`gd\ek%
=X`cli\kfi\X[#le[\ijkXe[Xe[]fccfnk_\`ejkilZk`fej^`m\e`ek_`j
dXelXcdXpi\jlck`ej\i`fljg\ijfeXc`ealip#`eZcl[`e^XdglkXk`fe#
\c\ZkifZlk`fefi[\Xk_%
K_\fne\if]k_`jdXZ_`e\&\hl`gd\ek`jjfc\cpi\jgfej`Yc\]fi`kjjX]\
lj\%K_`ji\jgfej`Y`c`kp`eZcl[\jYlk`jefkc`d`k\[kfgifg\i`ejkXccX$
k`fe`eXjX]\\em`ifed\ek#g\ijfee\ckiX`e`e^Xe[ljX^\Xlk_fi`qX$
k`fe#gifg\i`ejg\Zk`feXe[dX`ek\eXeZ\#dXelXcXmX`cXY`c`kpXe[
Zfdgi\_\ej`fe#Xggc`ZXk`fef]jX]\kp[\m`Z\j#YcX[\&Zlkk\i`ek\^i`kp#
Xe[k_\ljX^\f]g\ijfeXcgifk\Zk`m\\hl`gd\ek%
K_\dXel]XZkli\in`ccefkY\_\c[c`XYc\]fi`ealipfigifg\ikp
[XdX^\]ifde\^c`^\eZ\#`dgifg\ikiX`e`e^#dXZ_`e\df[`]`ZXk`fejfi
d`jlj\%
Jfd\[ljkZi\Xk\[Ypgfn\ijXe[`e^#jXn`e^#^i`e[`e^#[i`cc`e^#Xe[
fk_\iZfejkilZk`feXZk`m`k`\jZfekX`ejZ_\d`ZXcjbefnekfk_\JkXk\f]
:Xc`]fie`XkfZXlj\ZXeZ\i#Y`ik_[\]\Zkjfifk_\ii\gif[lZk`m\_Xid%
Jfd\\oXdgc\jf]k_\j\Z_\d`ZXcjXi\1
› C\X[]ifdc\X[$YXj\[gX`ekj%
› :ipjkXcc`e\j`c`ZX]ifdYi`Zbj#Z\d\ekXe[fk_\idXjfeipgif[lZkj%
› 8ij\e`ZXe[Z_ifd`ld]ifdZ_\d`ZXccp$ki\Xk\[cldY\i%
Pflii`jb]ifdk_\j\\ogfjli\jmXi`\j#[\g\e[`e^fe_fnf]k\epfl
[fk_`jkpg\f]nfib%Kfi\[lZ\pfli\ogfjli\kfk_\j\Z_\d`ZXcj1
Nfib`eXn\ccm\ek`cXk\[Xi\X#Xe[nfibn`k_Xggifm\[jX]\kp\hl`g$
d\ek#jlZ_Xjk_fj\[ljkdXjbjk_XkXi\jg\Z`Xccp[\j`^e\[kf]`ck\i
flkd`ZifjZfg`ZgXik`Zc\j%
Model D3274 Gravity Feed Spray Gun w/Regulator
SAFETY
For Your Own Safety Read Instruction Manual
Before Operating This Equipment
The purpose of safety symbols is to attract your attention to possible hazardous
conditions. This manual uses a series of symbols and signal words which are intended
to convey the level of importance of the safety messages. The progression of
symbols is described below. Remember that safety messages by themselves do not
eliminate danger and are not a substitute for proper accident prevention measures.
Indicates an imminently hazardous situation which, if
not avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, MAY result in minor or moderate injury.
It may also be used to alert against unsafe practices.
NOTICE
This symbol is used to alert the user to useful
information about proper operation of the
equipment.
Safety Instructions for Pneumatic Tools
5. KEEP CHILDREN AND VISITORS
AWAY. All children and visitors
should be kept at a safe distance
from work area.
1. KEEP ALL SAFETY DEVICES IN
PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking
to see that keys and adjusting
wrenches are removed from tool
before operation.
6. MAKE WORKSHOP CHILD PROOF by
locking your shop and shutting off
air valves.
7. DO NOT FORCE TOOL. It will do
the job better and safer at the rate
for which it was designed.
3. KEEP WORK AREA CLEAN. Cluttered
areas and benches invite accidents.
4. DO NOT USE IN DANGEROUS
ENVIRONMENT. Do not use
pneumatic tools in damp or wet
locations, or where any flammable
or noxious fumes may exist. Keep
work area well lighted.
8. USE THE RIGHT TOOL. Do not
force tool or attachment to do a
job for which it was not designed.
9. DO NOT USE UNDER THE
INFLUENCE OF DRUGS OR
ALCOHOL.
-1-
Model D3274 Gravity Feed Spray Gun w/Regulator
Safety Instructions for Pneumatic Tools
10.USE PROPER AIR HOSE for the
tool. Make sure your air hose is in
good condition and is long enough
to reach your work without
stretching.
17.DISCONNECT TOOLS before
servicing, changing accessories, or
moving to another location.
11.WEAR PROPER APPAREL. Do
not wear loose clothing, gloves,
neckties, rings, bracelets, or
other jewelry which may get
caught in moving parts. Non-slip
footwear is recommended. Wear a
protective hair covering to contain
long hair.
19.USE THE RECOMMENDED
ACCESSORIES. Consult owner’s
manual for recommended
accessories. The use of improper
accessories may cause risk of
injury.
18.DO NOT OVERREACH. Keep proper
footing/balance at all times.
20.CHECK FOR DAMAGED PARTS
BEFORE USING. Check for binding
and alignment of parts, broken
parts, part mounting, loose bolts,
and any other conditions that may
affect machine operation. Repair
or replace damaged parts.
12.ALWAYS USE SAFETY GLASSES.
Also use a face or dust mask
if cutting operation is dusty.
Everyday eyeglasses only have
impact resistant lenses, they are
NOT safety glasses.
21.NEVER LEAVE UNATTENDED TOOL
CONNECTED TO AIR. Disconnect
the air hose and do not leave tool
until it is relieved of any built up
pressure.
13.WEAR APPROVED HEARING
PROTECTION. Air escaping from
pneumatic tools can exceed safe
exposure limits and may cause
hearing damage with prolonged
exposure.
22.NEVER ALLOW UNTRAINED
USERS TO USE THIS TOOL WHILE
UNSUPERVISED.
14.SECURE WORK. Use clamps or a
vise to hold work when practical.
It is safer than using your hand
and frees both hands to operate
tool.
23.IF YOU ARE UNSURE OF THE
INTENDED OPERATION, STOP
USING TOOL. Seek formal training
or research books or magazines
that specialize in pneumatic tools.
15.MAINTAIN TOOLS WITH CARE.
Keep tools lubricated and clean
for best and safest performance.
Follow instructions for lubricating
and changing accessories.
24.BE AWARE OF HOSE LOCATION
WHEN USING PNEUMATIC TOOLS.
Hoses can easily become a tripping
hazard when laid across the floor
or spread out in a disorganized
fashion.
16.REDUCE THE RISK OF
UNINTENTIONAL FIRING. Do not
carry tool with hand on trigger
and always disconnect from air
when not in use.
-2-
Model D3274 Gravity Feed Spray Gun w/Regulator
Additional Safety Instructions for Spray Guns
1. Read this manual. This manual
contains proper operating
instructions for this spray gun.
8. PROTECTIVE CLOTHING. Protect
exposed skin from overspray by
wearing a protective suit or other
approved garment.
2. READ MATERIAL LABELS and
MATERIAL SAFETY DATA SHEETS
(MSDS). Read and know all the
instructions on the packaging label
and the MSDS before opening the
package. This information could
save your life.
9. UNSAFE USE. DO NOT point
or shoot spray gun directly at
yourself or another person or
animals. Do not attempt to use
the spray gun for any other use
than it was intended.
3. ALWAYS WEAR A NIOSH
APPROVED RESPIRATOR WHEN
SPRAYING OR WORKING AROUND
FINISHING MATERIALS.
10. STORAGE. Thoroughly clean and
dry spray gun before storage.
Store in an approved cabinet.
11. SOLVENTS. Always store solvents
and shop towels soaked in solvent
in approved containers.
4. FIRE EXTINGUISHERS. Always
have a fully charged multi class
or class B fire extinguisher in the
immediate area.
12. EYE PROTECTION. Wear eye
protection whenever spraying or
cleaning. Solvents and chemicals
can cause serious eye injury,
which could lead to blindness.
5. FLAMMABLE MATERIAL. NEVER
spray near open flame or where
any spark could occur.
13. OPERATING PRESSURE. DO NOT
exceed the recommended inlet air
pressure. Excessive pressure could
cause the spray gun to burst or
cause other internal equipment
damage.
6. FRESH AIR. Always provide
adequate exhaust to keep area
free of built up vapors, NEVER
spray in an enclosed space.
7. DISCONNECT COMPRESSED AIR.
Always disconnect the spray
gun from compressed air before
cleaning, changing attachments or
when performing maintenance of
any kind on this tool.
14. LOCAL LAWS. Consult local
authorities regarding exhaust and
waste disposal requirements.
No list of safety guidelines can be complete. Every shop environment is different.
Always consider safety first, as it applies to your individual working conditions. Use
this and other tools with caution and respect to avoid serious injury.
-3-
Model D3274 Gravity Feed Spray Gun w/Regulator
INTRODUCTION
Woodstock Technical
Support
This tool has been specially designed to
provide many years of trouble-free service. Close attention to detail, ruggedly
built parts and a rigid quality control program assure safe and reliable operation.
Woodstock International, Inc. is committed to customer satisfaction. Our intent
with this manual is to include the basic
information for safety, setup, operation,
maintenance, and service of this product.
We stand behind our tools! In the
event that questions arise about
your tool, please contact Woodstock
International Technical Support at
(360) 734-3482 or send e-mail to:
tech-support@shopfox.biz. Our knowledgeable staff will help you troubleshoot
problems and process warranty claims.
Read manual before operation.
Become familiar with the spray gun
safety and operation instructions
before beginning any work. Serious
personal injury may result if safety
or operational information is not
understood or followed.
If you need the latest edition of this
manual, you can download it from
http://www.shopfox.biz.
If you have comments about this
manual, please contact us at:
Woodstock International, Inc.
Attn: Technical Documentation
Manager
P.O. Box 2309
Bellingham, WA 98227
Email: manuals@woodstockint.com
-4-
Model D3274 Gravity Feed Spray Gun w/Regulator
SETUP
Unpacking
This tool has been carefully packaged for safe transportation. If you notice the machine
has been damaged during shipping, please contact your authorized Shop Fox dealer
immediately.
Inventory
The following is a description of the main components shipped with the Model D3274.
Lay the components out to inventory them.
Note: If you can't find an item on this list, check the mounting location on the tool
or examine the packaging materials carefully. Occasionally we pre-install certain
components for safer shipping.
D3274 Inventory (Figure 1)
Qty
A.. Material Cup.............................. 1
B.. Air Regulator.............................. 1
C.. Spray Gun................................. 1
D.. Service Wrench........................... 1
E.. Hex Socket Tool.......................... 1
F.. Filter....................................... 1
G.. Cleaning Brush............................ 1
B
A
C
D
E
F
G
Figure 1. Model D3274 inventory.
-5-
Model D3274 Gravity Feed Spray Gun w/Regulator
Specifications
Controls
Operating Air Pressure............. 30–50 PSI
Maximum Air Pressure.................. 70 PSI
Material Cup Capacity................. 600 CC
Air Consumption.................. 4.2–7.1CFM
Maximum Fluid Pressure............... 10 PSI
Cup Material.............................Plastic
Body Material.................Aluminum Alloy
Maximum Pattern Width.............. 250mm
Water-Based Material Compatible.......Yes
Weight.................................. 1.5 lbs.
Material Cup
Fluid Control
Atomizing
Pattern Control
Cap
Regulator Control
Trigger
Air Flow Control
Figure 3. Controls.
Assembly
•
Fluid Control: Controls the volume of
material that travels through the fluid
tip by adjusting how far the trigger
can be pulled back.
•
Pattern Control: Adjusts the spray
pattern from a round pattern to a
wide fan.
•
Air Flow Control: Adjusts the fluid
pressure inside the spray gun.
•
Atomizing Cap­: Adjusts the spray
pattern from vertical to horizontal.
•
Trigger­: Two stage trigger. Stage
one only releases compressed air for
blowing off the work piece. Stage two
sprays material.
3. Attach the regulator to the bottom of
the spray gun.
•
Material Cup: Holds the paint to be
sprayed.
4. Attach the air hose to the spray gun
regulator with a 1⁄4" NPT quick connect fitting (not included).
•
Regulator/Gauge: Regulates inlet air
pressure to the spray gun. It can be
attached directly to the gun for onthe-spot air adjustments or to the air
source.
1. Insert the filter into the gun body
with the knob pointing outward (see
Figure 2).
Figure 2. Installing filter.
2. Screw the cup onto the top of the
body.
5. Attach the spray gun to an air supply
regulated between 30 and 50 PSI.
Note: For the best results, use a hose
that will be dedicated for spray use
only. Do not use a hose that has been
used with an in-line oiler or other
possible contaminant.
-6-
Note: DO NOT attach the spray gun or
regulator control to an unregulated
air source that exceeds 120 PSI.
Model D3274 Gravity Feed Spray Gun w/Regulator
OPERATIONS
Spraying
The Model D3274 HVLP (high volume,
low pressure) spray gun set is designed
to spray a wide variety of materials
like lacquers, stains, primers, multicomponent paints, clear coats, acrylics,
epoxies etc. It is ideal for auto body and
woodworking projects.
EXPLOSION HAZARD! DO NOT smoke
or have any source of flame or spark
near spraying. Vapors will explode if
ignited.
To use your spray gun:
1. Read and follow the material
manufacturer's instructions for
spraying, reducing, safety, disposal,
and any other instruction on the label
or Material Safety Data Sheet (MSDS).
2. Ensure the cup is securely tightened
and all other fittings are secure to
avoid air leaks or material spills.
3. Use the regulator control (Figure 3),
to set the inlet air pressure to 30 PSI
or to the material manufacturer's
recommendations (not to exceed 70
PSI).
RESPIRATORY HAZARD! Always use
respirator rated for organic vapor
and solvent use when using spray
equipment. Failure to protect your
lungs can lead to respiratory illness
and nervous system damage.
4. Adjust the atomizing cap (Figure
3) for a vertical or horizontal spray
pattern. Refer to Atomizing Cap
and Fan Adjustments on Page 9 for
further explanation.
5. After the material has been reduced
to the manufacturer's specifications,
fill the cup with the thinned material.
6. Trial and error, along with a fair
amount of practice are necessary to
achieve the results you want. Test
your material flow and spray pattern
on a piece of cardboard or some
scrap of material similar to your
project.
TOXIC FUMES! Always use an approved
spray booth or well ventilated
area when spraying. NEVER spray
in an confined space where toxic
fumes and flammable vapors can
accumulate to deadly levels.
-7-
Model D3274 Gravity Feed Spray Gun w/Regulator
7. Adjust the fluid control knob (Figure
3), to start with a low volume of
material and keep the atomization as
low as possible. You will need to use
a combination of fluid control, inlet
air pressure, air flow control and
stroke speed to achieve the results
you want. Spray so the material wets
out nicely without running or sagging.
Note: Trigger position B (Figure
5) introduces air to the paint gun,
so that position C (spray), is dust,
spatter, and cloud free.
A–Off
B–Air
C–Spray
A
8. Use the pattern control knob (Figure
3), to adjust the spray fan to your
desired pattern.
6
7
B
C
8
7
6
Ldg`e^ZXZ
9. Keep the gun tip perpendicular to
the ground, parallel to the spraying
surface,­ and 6-8" from the work (as
shown in Figure 4) when spraying.
Do not allow your wrist to bend. This
will cause the gun to arc across the
surface and distribute the material
unevenly, possibly creating sags and
dry spots.
Figure 5. Spray positions.
+ each stroke by 50% while
11.Overlap
-
maintaining an even speed. This will
ensure even coverage as shown in
Figure 6. Overlapping less than 50%,
as shown in the figure to the right,
may lead to missed spots or streaky
results.
+
-
Figure 4. Spray technique.
NOTICE
Tipping spray gun may cause material
to spill out of the cup. Always hold
the spray gun perpendicular to the
ground to avoid potential spills and
gravity feed problems.
Yes
No
Figure 6. Overlap technique.
10. Begin spraying 2-3 inches before the
work and continue to the end of the
work, as shown in Figure 5. Continue
the motion for a few inches past
the work until you are ready for the
return stroke.
12.Spray stroke should have even
consistency and parallel edges. If it
doesn't, refer to Troubleshooting on
Page 12.
-8-
Model D3274 Gravity Feed Spray Gun w/Regulator
Atomizing Cap and Fan
Adjustments
Pattern
The atomizing cap needs to be adjusted
for horizontal or vertical spraying
patterns. Spraying in the wrong direction
may lead to material build up on the
atomizing cap horn. Many performance
problems with properly thinned paint are
caused by clogged atomizing holes on
the atomizing cap horns (see Cleaning on
Page 10).
Stroke
Pattern
Control
Figure 8. Set up for horizontal spray
stroke with vertical fan pattern.
Stroke
Pattern
Horns
Pattern
Control
Figure 7. Atomizing cap horns.
Figure 9. Set up for vertical spray stroke
with horizontal fan pattern.
Rotating the pattern adjustment control
in Figure 8 and 9 will give you a range
between the two patterns in Figure 10.
Figure 10. Fan pattern adjustment.
-9-
Model D3274 Gravity Feed Spray Gun w/Regulator
CLEANING & LUBRICATION
4. Disassemble the gun by unscrewing
the fluid control knob by hand, and
removing the spring and needle
(Figure 9).
Fluid Tip
Filter
Cup
EYE INJURY! Always wear safety
glasses when disassembling the spray
gun. The material cup may still be
pressurized. Parts may also shoot out
of the gun pressure is released from
the springs.
Fluid Control
Knob
Atomizing
Cap
Needle
Spring
Figure 11. Disassembly for cleaning.
5. Unscrew the atomizing cap with your
fingers and the fluid tip with the
service wrench (Figure 1). The fully
disassembled gun should look like
Figure 9.
Cleaning
Proper cleaning is the best way to ensure
trouble-free performance from your spray
gun. If your gun is not thoroughly cleaned,
damage and poor spraying will result.
Problems caused by improper cleaning will
not be covered by the warranty. Clean the
spray gun immediately after each use.
6. Rinse these parts thoroughly in
solvent then dry with compressed air
or let air dry.
Basic spray gun cleaning:
1. Spray a small amount of solvent
through the spray gun.
Note: Check with local laws
regarding this practice. If you are
spraying on a regular basis, spraying
solvents into the air may be illegal. A
cabinet style spray gun cleaner may
be required.
Note: If the small holes in the
atomizing cap become blocked, soak
them in clean solvent. If the blockage
still exists, clear it with a small
needle, taking great care not to
enlarge or damage the hole. Damage
to the hole will create a disrupted
spray pattern.
7. Use the cleaning brush with solvent
to clean the inner orifice and other
hard to reach areas on the outside of
the spray gun body.
2. DISCONNECT THE SPRAY GUN FROM
AIR!
8. Wipe the rest of the gun body with a
shop towel and dry.
3. Put on safety glasses and unscrew the
cup.
-10-
Model D3274 Gravity Feed Spray Gun w/Regulator
Depending on the amount of use and the
type of material used, the spray gun may
need to be disassembled and cleaned
beyond what is mentioned on Page 10.
If spray patterns become affected due
to internal blockages or the gun will be
stored for an extended amount of time,
follow these additional cleaning instructions.
EXPLOSION HAZARD! Chlorinated
Solvents like Tricloroethane and
Methylene Chloride (methyl chloride)
can chemically react with aluminum
and may explode. Many parts in spray
guns are made of aluminum. Read
solvent label carefully before using
solvent.
Advanced spray gun cleaning:
NOTICE
1. Follow Steps 1–5 on Page 10.
DO NOT soak the spray gun body
in solvent. Prolonged exposure to
solvent will rapidly deteriorate the
spray gun washers and seals. Ignoring
this notice will void your warranty.
2. Insert the bigger end of the hex
socket tool into the head of the
disassembled spray gun. Use the
service wrench on the end of the hex
socket tool as a lever to remove the
fluid nozzle plug and seals, as shown
in Figure 10.
Lubrication
3. Insert the smaller end of the hex
socket tool into the head of the spray
gun. Use the service wrench on the
end of the hex socket tool as a lever
to remove the screw and spring.
Lubricate the following areas with
spray gun lube after cleaning:
A.
B.
C.
D.
E.
F.
4. Follow Steps 6–8 on Page 10.
Atomizing Cap Threads
Air Valve Packing
Trigger Pin
Air Flow Control Valve
Pattern Control
Fluid Control Knob
After each cleaning, apply a thin film
of petroleum jelly to the needle spring
before reassembling.
Hex
Socket
Tool
Service
Wrench
A
F
Figure 12. Removing fluid nozzle plug.
B
E
C
D
Figure 13. Lubrication points.
-11-
Model D3274 Gravity Feed Spray Gun w/Regulator
Troubleshooting
NOTICE
Before Troubleshooting, make sure your paint is properly thinned or reduced
according to the instructions given by the paint manufacturer.
Symptom
Possible Cause
Possible Solution
Fluttering or
Spitting spray.
1.Dry or worn fluid tip seat
permits air to seep into fluid
passage.
2.Material level too low.
3.Fluid tip or strainer obstructed.
4.Dry needle packing.
1.Tighten fluid tip or replace
seat with new one.
1.Atomizing cap holes are
obstructed.
2.Build-up on top or bottom of
fluid tip.
3.Build-up on atomizing cap is
on needle seat.
1.Clear holes.
1.Left or right side horn holes
are plugged.
2.Build-up on left or right side
of fluid tip.
3.Build-up of material inside
atomizing cap.
1.Clear holes.
1.The material flow exceeds
the atomizing cap capacity.
1.Lower fluid flow.
2.Inlet air pressure is too low.
2.Increase inlet air pressure.
3.Material is too thick.
3.Thin material.
1.Volume control turned in too
far.
2.Inlet air pressure too high.
1.Increase volume.
3.Fluid pressure is too low.
3.Increase fluid pressure.
4.Material is too thin.
4.Adjust material.
1.No pressure at gun.
2.Fluid passages dirty.
1.Check air supply.
2.Clean gun, remove any
obstructions.
3.Open.
4.Refill.
Uneven top or bottom pattern.
Right or left arc
pattern.
Heavy deposit of
material in center.
Narrow center pattern.
No spray output.
3.Fluid control closed.
4.Out of paint.
-12-
2.Add material.
3.Clean.
4.Lubricate needle.
2.Clean.
3.Clean.
2.Clean.
3. Clean.
2.Reduce inlet air pressure.
Model D3274 Gravity Feed Spray Gun w/Regulator
Symptom
Possible Cause
Possible Solution
Excessive overspray.
1.Fluid pressure too high.
2.Gun is too far from surface.
1.Reduce fluid pressure.
2.Keep gun at recommended
distance.
3.Slow down and maintain
consistent, even parallel
stroke.
3.Spraying too fast.
Unable to control
spray fan.
Runs and sags.
1.Pattern adjustment screw is
not seating properly.
2.Atomizing cap is loose.
1.Clean or replace.
1.Spraying too slowly.
2.Gun is too close to surface.
1.Adjust spraying speed.
2.Adjust spraying distance to
6–8" from surface.
3.Replace damaged seals.
3.Damaged seal.
2.Tighten atomizing cap.
Material leaks from
cup.
1.Cap not secure.
2.Cup not tight on gun body.
3.Leaking from cap vent hole.
1.Tighten.
2.Tighten.
3.Hold gun upright do not
tilt.
Material leaks from
gun.
1.Fluid tip loose.
2.Dry or damaged seals.
3.Excessive pressure.
1.Tighten.
2.Replace seals.
3.Reduce pressure.
Thick dimpled finish aka "Orange
Peel."
1.Holding gun too close to surface.
2.Inlet air pressure too low.
3.Material not properly mixed.
1.Spray at recommended distance.
2.Check inlet air pressure.
3.Follow manufacturer's
instructions.
4.More surface prep is
required.
4.Surface is dirty or oily.
Dry Spray.
1.Inlet air pressure too high.
2.Gun too far from surface.
3.Gun stroke too fast.
1.Lower inlet air pressure.
2.Keep gun at recommended
distance.
3.Slow down and maintain
consistent even parallel
stroke.
Gun leaks from
fluid tip.
1.Debris will not let the needle
seat with the fluid tip.
1. Clean or replace both.
Contaminated
paint.
1.Water or oil in the air line.
1.Install an in-line air filter.
2.Replace air line.
3.Spray gun filter is missing.
-13-
Model D3274 Gravity Feed Spray Gun w/Regulator
D3274 PARTS BREAKDOWN
28
29
23 24
25 26
27
30
30A
31
16A
32
13
14
15
16
17 18 19 20 21 22
33
35 36 37
34
38
39
45
44
12
11
10
9
8
1A
8A
43
42
7
6
5
2
4
40A
3
46
1
52
*51
47
48
49
50
* Not Included; for aftermarket purchase only
-14-
41
40
Model D3274 Gravity Feed Spray Gun w/Regulator
D3274 PARTS LIST
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1A
1
2
3
4
5
6
7
8A
8
9
10
11
12
13
14
15
16A
16
17
18
19
20
21
22
23
24
25
26
AIR INLET VALVE ASSEMBLY
AIR ADJ. SCREW
AIR ADJ. KNOB
O-RING 2.5 X 2.1
DOMED SEAL WASHER
AIR ADJ. SPRING
AIR INLET VALVE
SWITCH SPRING
AIR VALVE BODY ASSEMBLY
AIR VALVE BODY
SWITCH KNOB
O-RING 2.4 X 1.8
DOMED SEAL WASHER
DIRECTION SCREW
LOCKED SPRING
NOZZLE NUT
SEAL WASHER 30MM
ATOMIZER ASSEMBLY
ATOMIZER
FLUID NOZZLE
FLUID NOZZLE PLUG
SEAL WASHER 10MM
DIRECTION SCREW M11-1 X 7
DOMED SEAL WASHER 3.5
COMPRESSION SPRING 6.3 X 14
TRIGGER PIN I
TRIGGER PIN II
TRIGGER
E-CLIP 4MM
27
28
29
30A
30
31
32
33
34
35
36
37
38
39
40A
40
41
42
43
44
45
46
47
48
49
50
*51
52
E-CLIP 4MM
BREATHER PLUG
CONTAINER COVER
CONTAINER ASSEMBLY
CONTAINER
FILTER
FLUID INLET JOINT SEAL
FLUID INLET JOINT
HANGER
FLUID ADJ. NEEDLE
COMPRESSION SPRING 6 X 37
JOINT CAP
FLUID ADJ. KNOB
FLAT HD SCR M4-.7 X 8
PATTERN ADJ. KNOB ASSEMBLY
PATTERN ADJ. KNOB
PATTERN ADJ. KNOB
COPPER WASHER 8MM
PATTERN ADJ. SCREW
O-RING 6 X 2
E-CLIP 6MM
AIR INLET 1/4" NPT
MULTI-TOOL WRENCH
HEX SOCKET TOOL
CLEANING BRUSH
AIR REGULATOR
O-RING KIT
GUN BODY
XD3274001A
XD3274001A
XD3274001A
XD3274001A
XD3274001A
XD3274001A
XD3274001A
XD3274008A
XD3274008A
XD3274008A
XD3274008A
XD3274008A
XD3274008A
XD3274008A
XD3274016A
XD3274016A
XD3274016A
XD3274016A
XD3274016A
XD3277008
XD3277009
XD3277010
XD3277011
XD3277012
XD3277013
XD3274023
XD3274024
XD3274025
XPEC02M
-15-
XPEC02M
XD3274030A
XD3274030A
XD3274030A
XD3274030A
XD3277022
XD3274032
XD3277023
XD3274034
XD3274035
XD3277033
XD3277032
XD3274038
XPFH31M
XD3274040A
XD3274040A
XD3274040A
XD3274040A
XD3274040A
XPOR0062
XPEC09M
XD3277041
XD3277042
XD3277043
XD3277044
XD3274050
XD3274051
XD3274052
WARRANTY AND RETURNS
Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects
from workmanship and materials for a period of two years from the date of original
purchase by the original owner. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence or accidents, lack of maintenance, or
reimbursement of third party expenses incurred.
Woodstock International, Inc. will repair or replace, at its expense and at its option,
the Shop Fox machine or machine part which in normal use has proven to be defective,
provided that the original owner returns the product prepaid to a Shop Fox factory
service center with proof of their purchase of the product within two years, and
provides Woodstock International, Inc. reasonable opportunity to verify the alleged
defect through inspection. If it is determined there is no defect, or that the defect
resulted from causes not within the scope of Woodstock International Inc.'s warranty,
then the original owner must bear the cost of storing and returning the product.
This is Woodstock International, Inc.'s sole written warranty and any and all warranties
that may be implied by law, including any merchantability or fitness, for any particular
purpose, are hereby limited to the duration of this written warranty. We do not
warrant that Shop Fox machinery complies with the provisions of any law or acts. In
no event shall Woodstock International, Inc.'s liability under this warranty exceed the
purchase price paid for the product, and any legal actions brought against Woodstock
International, Inc. shall be tried in the State of Washington, County of Whatcom. We
shall in no event be liable for death, injuries to persons or property or for incidental,
contingent, special or consequential damages arising from the use of our products.
Every effort has been made to ensure that all Shop Fox machinery meets high quality
and durability standards. We reserve the right to change specifications at any time
because of our commitment to continuously improve the quality of our products.
Warranty Registration
Name____________________________________________________________________________________
Street___________________________________________________________________________________
City__________________________ State____________________________Zip_________________________
Phone #_______________________ Email___________________________Invoice #____________________
Model #_________Serial #______________Dealer Name__________________Purchase Date___________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us
develop better products and services. Of course, all information is strictly confidential.
CUT ALONG DOTTED LINE
1. How did you learn about us?
__
Advertisement
__
Mail Order Catalog
______ Friend
______ Website
_ ____ Local Store
_ ____ Other:
2._ How long have you been a woodworker/metalworker?
__
0-2 Years
______ 2-8 Years
_____ 8-20 Years ______ 20+ Years
3._ How many of your machines or tools are Shop Fox?
__
0-2
______ 3-5
_____ 6-9
______ 10+
4. Do you think your machine represents a good value?
______ Yes
_ ____ No
5. Would you recommend Shop Fox products to a friend?
______ Yes
_ ____ No
6._ What is your age group?
__
20-29
__
50-59
______ 30-39
______ 60-69
7._ What is your annual household income?
__
$20,000-$29,000
______ $30,000-$39,000
__
$50,000-$59,000
______ $60,000-$69,000
_ ____ 40-49
_ ____ 70+
_ ____ $40,000-$49,000
_ ____ $70,000+
8._ Which of the following magazines do you subscribe to?
____
____
____
____
____
____
____
____
____
____
Cabinet Maker
Family Handyman
Hand Loader
Handy
Home Shop Machinist
Journal of Light Cont.
Live Steam
Model Airplane News
Modeltec
Old House Journal
____
____
____
____
____
____
____
____
____
____
Popular Mechanics
Popular Science
Popular Woodworking
Practical Homeowner
Precision Shooter
Projects in Metal
RC Modeler
Rifle
Shop Notes
Shotgun News
____
____
____
____
____
____
____
____
____
Today’s Homeowner
Wood
Wooden Boat
Woodshop News
Woodsmith
Woodwork
Woodworker West
Woodworker’s Journal
Other:
9._ Comments:___________________________________________________________________
_ _____________________________________________________________________________
_ _____________________________________________________________________________
_ _____________________________________________________________________________
_ ___________________________________________________________________
_ ___________________________________________________________________
FOLD ALONG DOTTED LINE
Place
Stamp
Here
Woodstock international inc.
p.o. box 2309
bellingham, wa 98227-2309
FOLD ALONG DOTTED LINE
tape along edges--please do not staple