2005

2005
INSTALLATION
INSTRUCTIONS
Accessory
Application
in-VEHICLE
ENTERTAINMENT SYSTEM
2005 TSX
Publications No.
BII 28366
Issue Date
OCT 2004
PARTS LIST
Attachment Kit
P/N 08B23-SDA-101A
Monitor bracket
i-VES harness
FM modulator bracket
Main harness
2 Washer-screws, 5 x 16 mm
DIN Harness
Washer-screw, 5 x 12 mm
Room light harness
2 Washer-screws, 5 x 25 mm
5 Square-neck bolts
Room light gasket
5 Flange nuts, 4 mm
Flange nut, 5 mm
Accord template
(Not used)
16 Wire ties
TSX template
Wire ties with clip
(Not used)
6 Cushion tapes
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
BII 28366 (0410)
08B23-SEC-2000-91
1 of 18
Monitor Kit (sold separately):
P/N 08A23-2E1-011
Audio Attachment Kit (sold separately):
P/N 08B06-SEC-210
Right upper player bracket
Monitor console
Left upper player bracket
DVD player
Lower player bracket
Right player bracket
FM modulator
Left player bracket
Remote control
Player panel
2 Headphones
BUS cable
(Not used)
2 Wire ties
5 Washer-screws, 5 x 8 mm
Wire tie with clip
(Not used)
2 Screw caps
8 Flange nuts, 6 mm
2 Latches
Owner’s Manual
Cushion tape
2 of 18
BII 28366 (0410)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
3.
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Flat-tip screwdriver
Clip remover
10 mm Combination wrench
Ratchet
7 mm, 8 mm, 10 mm, 12 mm, and 14 mm Sockets
Torque wrench
Utility knife
Isopropyl alcohol
Masking tape
Piece of steel wire
Shop towel
Electrical tape
Scissors
Hook tool
Diagonal cutters
UTILITY
KNIFE
TSX
TEMPLATE
2D11010S
Cut out these
areas.
Illustration of the in-vehicle Entertainment System
Installed in the Car
4.
DIN
HARNESS
i-VES
HARNESS
Using the utility knife, cut out the marked areas
from the TSX template along the lines.
MAIN
HARNESS
Close the sunshade. Position the TSX template on
the headliner, align the interior light and the
headliner clip, and tape the TSX template to the
headliner using strips of masking tape.
HEADLINER
CLIP
Cut out
INTERIOR
the area.
LIGHT
UTILITY
KNIFE
SUNSHADE
DVD
PLAYER
FM
MODULATOR
ROOM LIGHT MONITOR
HARNESS
CONSOLE
2031400S
MASKING
TAPE
INSTALLATION
Customer Information: The information in this
installation instruction is intended for use only by
skilled technicians who have the proper tools,
equipment, and training to correctly and safely add
equipment to your car. These procedures should not
be attempted by “do-it-yourselfers.”
HEADLINER
5.
1.
Make sure you have the anti-theft code for the
radio, and the navigation system, if equipped, then
write down the frequencies for the preset buttons.
2.
Disconnect the negative cable from the battery.
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
BII 28366 (0410)
TSX
TEMPLATE
2031011S
Using the utility knife, cut out the headliner around
the edge of the TSX template.
3 of 18
6.
Remove the center console panel.
A/T Model:
M/T Model:
•
Gently pry up on the center console panel to
release the eight clips.
•
Unplug the two seat heater connectors (if
equipped), and remove the center console
panel.
•
•
Remove the shift knob by turning it
counterclockwise.
Remove the lock nut.
SHIFT
KNOB
CLIPS (8)
CENTER CONSOLE
PANEL
LOCK
NUT
2031021S
2031040S
•
Gently pry up on the center console panel to
release the eight clips.
•
Unplug the two seat heater connectors (if
equipped), and remove the center console
panel.
SEAT HEATER CONNECTOR
7.
Open the pocket lid. Pull the pocket out toward
you to release the four clips, unplug the
illumination bulb, unclip the illumination bulb
harness from the pocket, and remove the pocket.
Take care not to damage the illumination bulb.
CLIPS (8)
CENTER
CONSOLE
PANEL
ILLUMINATION
BULB
CLIP
LID
CLIPS (4)
POCKET
2031030S
2031051S
SEAT HEATER CONNECTOR
4 of 18
BII 28366 (0410)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
2031021S
2031040S
2031030S
2031051S
8.
Remove the coin pocket holder or ashtray holder.
9.
Remove the passenger’s dashboard trim:
With a Coin Pocket Holder:
•
Open the glove box.
•
Remove the four self-tapping screws.
•
•
Gently pull out the coin pocket holder, unplug
the vehicle connector and the vehicle clip, and
remove the coin pocket holder.
Release one clip on the right side by inserting
the end of a flat-tip screwdriver wrapped with
the shop towel between the passenger’s
dashboard trim and the dashboard side cover.
•
Pull the passenger’s dashboard trim out toward
you to release the other five clips, and remove
the passenger’s dashboard trim.
SELF-TAPPING
SCREW (Reuse.)
VEHICLE
CLIP
CLIPS (6)
FLAT-TIP
SCREWDRIVER
PASSENGER’S
DASHBOARD
TRIM
SHOP
TOWEL
DASHBOARD
SIDE COVER
VEHICLE
CONNECTOR
COIN POCKET
HOLDER
GLOVE
BOX
2N03011S
With an Ashtray Holder:
•
Remove the four self-tapping screws.
•
Gently pull out the ashtray holder, unplug the
illumination bulb, the vehicle connector and the
cigarette lighter harness 2-pin connector, and
then remove the ashtray holder.
10. Using a hook tool, pull out the clip closest to the
steering column as shown.
HOSE
SELF-TAPPING
SCREW (Reuse.)
VEHICLE
CONNECTOR
2031071S
VEHICLE
CONNECTOR
HOOK
TOOL
VEHICLE
CLIP
DRIVER’S
INSTRUMENT
SIDE TRIM
3123011B
CLIPS (3)
ASHTRAY
HOLDER
ILLUMINATION
BULB
CIGARETTE
LIGHTER HARNESS
2-PIN CONNECTOR
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
11. Remove the driver’s inner dashboard trim (remove
two clips, unplug the vehicle connector and hose).
3305011S
BII 28366 (0410)
5 of 18
12. Remove the hazard switch by releasing the
retaining tab and unplugging the vehicle
connector.
14. Pry up on the four retaining tabs that fasten the
cap to the left front door sill, and remove the cap.
IGNITION KEY
SELF-TAPPING
SCREW
CAP
RETAINING
TABS (4)
KEY
CYLINDER
RETAINING
TAB
VEHICLE
CONNECTOR
LEFT FRONT
DOOR SILL
2N27150S
2131020T
HAZARD
SWITCH
15. Remove the self-tapping screw. Insert the ignition
key into the key cylinder, and turn it clockwise
until it will no longer turn. Using a flat-tip
screwdriver, pry up on the key cylinder, and
remove it from the left front door sill.
13. Remove the AUDIO-HVAC display module (two
bolts, three self-tapping screws, and pull the
center panel out toward you to release the eight
clips).
16. Remove the left front door sill (five clips and two
retaining tabs).
CLIPS (8)
AUDIO-HVAC
DISPLAY MODULE
CLIPS (5)
LEFT FRONT
DOOR SILL
FRONT
SELFTAPPING
SCREWS
(3)
RETAINING
TABS (2)
BOLT
2031101S
2131010T
6 of 18
BII 28366 (0410)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
17. Remove the left rear door sill (three clips).
CLIPS (2)
19. Remove the center pillar weatherstrip. Pull the left
center pillar lower trim and the left center pillar
upper trim out toward you to release the four clips,
and remove the upper and lower trims.
LEFT REAR
DOOR SILL
LEFT REAR
DOOR SILL
LEFT CENTER
PILLAR UPPER TRIM
CLIPS (4)
FRONT
CLIP
CENTER PILLAR
WEATHERSTRIP
CENTER PILLAR
WEATHERSTRIP
2N27160S
2031110S
LEFT CENTER PILLAR
LOWER TRIM
18. Release the left center pillar upper anchor cover
(three tabs). Remove the left center pillar upper
anchor bolt.
LEFT CENTER
PILLAR UPPER
ANCHOR COVER
20. Remove the weatherstrip. Pull the left front pillar
trim out toward you to release the two clips, and
remove the left front pillar trim.
With side curtain airbag
CLIP
(Remove.)
CLIPS (2)
LEFT FRONT
PILLAR TRIM
LEFT CENTER PILLAR
UPPER ANCHOR
BOLT
2031120S
WEATHERSTRIP
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
BII 28366 (0410)
2304071M
7 of 18
21. Remove the driver’s dashboard lower cover (three
clips, one pin, and one holder).
CLIPS (3)
23. Remove the four bolts that fasten the roof
console. Remove the roof console by pulling it out
toward you and unplugging the two vehicle
connectors.
VEHICLE
CONNECTOR
ROOF
CONSOLE
HOLDER
2N19010S
DRIVER’S
DASHBOARD
LOWER COVER
PIN
BOLT
22. Remove the left and right lenses from the roof
console (four retaining tabs).
2301011M
24. Remove the cap from the left sunvisor (four
retaining tabs).
ROOF
CONSOLE
VEHICLE
CONNECTOR
RETAINING
TABS (4)
RIGHT
LENS
LEFT
LENS
RETAINING
TABS (4)
CAP
RETAINING
TABS (4)
LEFT
SUNVISOR
2304010M
TORX SCREW
2326080T
25. Remove the left sunvisor (two T25 torx screws),
and unplug the connector.
8 of 18
BII 28366 (0410)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
26. Remove the two caps from the left front grab rail,
and remove the grab rail (two bolts).
Routing the i-VES Harness/Monitor Harness and
Installing the Monitor Console
28. Route the i-VES harness (yellow label side) from
the left front pillar trim opening to the driver’s
dashboard lower cover opening.
CAP
i-VES HARNESS
LEFT FRONT
PILLAR TRIM
OPENING
LEFT FRONT
GRAB RAIL
YELLOW
LABEL
BOLT
2031130S
27. Remove the two caps from the left rear grab rail,
and remove the grab rail (two bolts).
2031152S
DRIVER’S DASHBOARD
LOWER COVER
OPENING
i-VES
HARNESS
CAP
29. Continue routing the i-VES harness from the
driver’s dashboard lower cover opening to the
pocket opening .
POCKET
OPENING
LEFT REAR
GRAB RAIL
BOLT
i-VES
HARNESS
2031140S
2031161S
DRIVER’S DASHBOARD
LOWER COVER OPENING
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
BII 28366 (0410)
9 of 18
32. Continue routing the i -VES harness to the rear
along the vehicle harness, and out of the headliner
opening you made, so that the distance between
the headliner opening and the i -VES harness
terminal end is 200 mm.
30. Using a flat-tip screwdriver, push the hooks, turn
the holders 90°, and pull out to remove the
sunvisor holders.
HEADLINER
OPENING
200 mm
i-VES
HARNESS
HOOKS (2)
SUNVISOR
HOLDERS (2)
VEHICLE
HARNESS
FLAT-TIP
SCREWDRIVER
2326210T
2326231T
33. Remove the rear interior light:
31. Route the i-VES harness up along the front pillar
and under the headliner alongside the vehicle
harness as shown.
•
Remove the lens (four retaining tabs).
•
Remove the two screws, lift out the rear interior
light, unplug the connector, and remove the
rear interior light.
VEHICLE CONNECTOR
VEHICLE
HARNESS
FRONT
i-VES
HARNESS
HEADLINER
REAR
INTERIOR
LIGHT
HEADLINER CLIP
(Turn 90°
counterclockwise
to remove.)
2031170S
LENS
SCREW
RETAINING
TABS (4)
2326240T
34. Remove the headliner clip by turning it 90°
counterclockwise.
10 of 18
BII 28366 (0410)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
35. Route a piece of steel wire through the hole in the
rear interior light opening and out through the
cutout made in the headliner in step 5.
REAR INTERIOR
LIGHT OPENING
ELECTRICAL
TAPE
39. Reinstall the rear interior light.
40. Using the isopropyl alcohol on a shop towel, clean
the area where the cushion tape will attach. Attach
one cushion tape to the monitor bracket as shown.
HEADLINER
OPENING
MONITOR
BRACKET
BRACKET
PIECE OF STEEL WIRE
(Wrap the end around the
room light harness
connector, and pull it up.)
ROOM
LIGHT
HARNESS
CUSHION
TAPE
2326250T
3204060Y
36. Wrap the end of the steel wire around the room
light harness connector, and secure it with
electrical tape. Pull the room light harness up
through the rear interior light opening, and out
through the headliner opening.
41. Insert the monitor bracket into the headliner
opening.
37. Plug the room light harness 3-pin connectors in
between the rear interior light and the vehicle 3-pin
connectors.
HEADLINER
OPENING
VEHICLE 3-PIN
CONNECTOR
ROOM LIGHT
HARNESS 3-PIN
CONNECTOR
ROOM LIGHT
HARNESS 3-PIN
CONNECTOR
CUSHION
TAPE
MONITOR
BRACKET
REAR
INTERIOR
LIGHT
ROOM LIGHT
HARNESS
3204070Y
2326260T
38. Using isopropyl alcohol, clean the areas where the
two cushion tapes will attach. Secure the room
light harness to the headliner with two cushion
tapes in the areas shown.
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
BII 28366 (0410)
11 of 18
42. Install the monitor bracket to the vehicle frame
with five square-neck bolts and five 4 mm flange
nuts holding the square-neck bolts.
45. Connect the room light harness 3-pin connector
and the i-VES harness terminal to the monitor
console 3-pin connector and monitor console
terminal.
VEHICLE
FRAME
i-VES
HARNESS
TERMINAL
MONITOR
HARNESS 3-PIN
CONNECTOR
SQUARENECK
BOLTS (5)
MONITOR
CONSOLE
3-PIN
CONNECTOR
MONITOR
BRACKET
SQUARENECK BOLTS
(5)
VEHICLE
FRAME
MONITOR
CONSOLE
TERMINAL
4 mm
FLANGE
NUTS (5)
3205030Y
MONITOR
CONSOLE
FRONT
MONITOR
BRACKET
3204080Y
43. Remove the left and right lenses from the monitor
console.
46. With an assistant holding the monitor console,
clean the areas where the cushion tapes will
attach. Secure the i-VES harness to the underside
of the vehicle frame with two cushion tapes.
LEFT LENS
MONITOR
CONSOLE
RIGHT
LENS
MONITOR
CONSOLE
CUSHION
TAPE
i-VES
HARNESS
WIRE
TIE
VEHICLE
HARNESS
2N28160S
WIRE
TIE
MARK
MONITOR
GASKET
2326290T
47. Secure the i-VES harness to the vehicle harness
with four wire ties in the areas shown.
44. Install the monitor gasket on the console while
aligning the mark of the monitor gasket with the
mark of the monitor console.
12 of 18
BII 28366 (0410)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
50. Along the front pillar, secure the i-VES harness to
the vehicle harness with four wire ties.
48. Holding the monitor console, secure the 3-pin
connectors and terminals you plugged into the
back of the monitor console as shown.
i-VES
HARNESS
WIRE TIES (4)
3-PIN
CONNECTOR
VEHICLE
CLIPS (4)
VEHICLE
HARNESS
MONITOR
CONSOLE
TERMINALS
CUSHION
TAPE
LEFT FRONT
PILLAR
2031180S
51. Near the fuse box and under the driver’s
dashboard lower cover, secure the i-VES harness
to the vehicle harness with three wire ties in the
areas shown.
3204100Y
3-PIN
CONNECTORS
TERMINALS
49. Position the monitor console on the monitor
bracket, and install the two 5 x 16 mm washerscrews and the two 5 x 25 mm washer-screws. Do
not pinch the i-VES harness and monitor harness
between the monitor console and the monitor
bracket. Install the two screw caps, and then
reinstall the left and right lenses.
WIRE TIE
MONITOR
BRACKET
i-VES
HARNESS
VEHICLE
HARNESS
MONITOR
CONSOLE
VEHICLE
HARNESS
FRONT
FUSE BOX
WIRE TIE
2031190S
5 x 25 mm
WASHER
SCREW
RIGHT
LENS
LEFT
LENS
SCREW
CAP
5 x 16 mm
WASHER
SCREW
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
SCREW
CAP
3205040Y
BII 28366 (0410)
13 of 18
52. Secure the i-VES harness to the vehicle harness
with three wire ties in the area shown.
54. Apply masking tape as shown.
NOTE: Failure to attach masking tape to protect
the bottom edge of the AUDIO-HVAC display
module can result in damage. The AUDIO-HVAC
display module is available only as a complete
assembly.
VEHICLE
HARNESS
6 mm FLANGE NUT
LEFT UPPER
PLAYER
BRACKET
STUDS (2)
i-VES
HARNESS
RIGHT
UPPER
PLAYER
BRACKET
WIRE TIE
STUDS (2)
3305050S
6 mm FLANGE NUT
2031200S
55. Insert the studs from the right and left upper
player brackets into the holes in the vehicle frame,
and install one 6 mm flange nut to each stud.
Push the player brackets outward, and tighten the
flange nuts.
Installing the DVD Player
53. Plug in the main harness.
Unplug the vehicle 20-pin connector from the
audio unit or the navigation unit. Route the main
harness behind the vehicle frame as shown, and
plug the main harness 20-pin connectors in
between the vehicle 20-pin connector and the
audio unit or the navigation unit.
56. Plug the DIN harness 90° terminal into the FM
modulator.
FM MODULATOR
BRACKET
90° TERMINAL
MAIN HARNESS
20-PIN
CONNECTOR
5 x 12
mm
WASHERSCREW
VEHICLE 20-PIN
CONNECTOR
5 mm
FLANGE
NUT
5 x 8 mm
WASHERSCREW
FM
MODULATOR
MAIN
HARNESS
20-PIN
CONNECTOR
VEHICLE
FRAME
AUDIO UNIT
OR
NAVIGATION
UNIT
DIN HARNESS
MAIN
HARNESS
2031211S
2031231S
LOWER PLAYER
BRACKET
57. Attach the FM modulator bracket to the lower
player bracket with one 5 x 12 mm washer-screw
and one 5 mm flange nut.
58. Attach the FM modulator to the FM modulator
bracket with one 5 x 8 mm washer-screw.
14 of 18
BII 28366 (0410)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
59. Remove the two nuts from the premium sound
system amp.
61. Insert the studs into the holes in the lower player
bracket, then install the lower player bracket with
the two nuts removed in step 59.
LOWER
PLAYER
BRACKET
NUT
(reuse)
3305060S
NUT
(reused)
PREMIUM
SOUND SYSTEM
AMP
3305070S
STUD
60. On the right side of the pocket opening, unplug the
vehicle antenna leads and plug them into the FM
modulator antenna lead. Plug the FM modulator
antenna lead into the vehicle antenna lead. Secure
the antenna leads you plugged in with one wire tie.
FM MODULATOR
POCKET
OPENING
62. Loop the excess antenna leads, and secure the
antenna leads with two wire ties.
VEHICLE HARNESS
WIRE TIE
i-VES
HARNESS
TERMINAL
FM MODULATOR
ANTENNA LEAD
DIN HARNESS
TERMINAL
2031261S
WIRE
TIE
VEHICLE
ANTENNA
LEAD
ANTENNA
LEAD
63. Align the end of the i -VES harness terminal with
the end of the DIN harness terminal as shown;
loop the excess i -VES harnesses, and secure the
loop to the vehicle harness with two wire ties.
2031252S
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
BII 28366 (0410)
15 of 18
67. Remove the illumination bulb, and attach the bulb
harness with electrical tape as shown. Loop the
excess illumination bulb harness, and secure it to
the vehicle harness with one wire tie.
64. Using scissors, cut the cushion tape in half, and
attach the two halves of the cushion tape to the
player in the areas shown.
CUSHION TAPE
(Cut in half.)
ELECTRICAL
TAPE
ILLUMINATION
BULB
(Remove.)
WIRE TIE
VEHICLE
HARNESS
50 mm
ILLUMINATION
BULB HARNESS
50 mm
PLAYER
2N21112S
3108270S
65. Install one latch to each of the right and left player
brackets.
5 X 8 mm
WASHER-BOLTS
(4)
68. Cut off the pocket clip tabs with the diagonal
cutters as shown.
LEFT PLAYER
BRACKET
POCKET
OPENING
RIGHT PLAYER
BRACKET
LATCH
LATCH
3305030S
POCKET
CLIP TAB
PLAYER
2031282S
66. Position the player on the right and left player
brackets, and install four 5 x 8 mm washer-bolts.
16 of 18
BII 28366 (0410)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
69. Apply masking tape in the area shown. Reinstall
the coin pocket holder or ashtray holder.
70. Plug the main harness 4-pin connector, the DIN
harness terminal, and the i-VES harness terminal
into the rear of the DVD player (plug the i-VES
harness terminal into the yellow label position).
With a Coin Pocket Holder:
SELF-TAPPING
SCREW
(reused)
MASKING
TAPE
YELLOW
LABEL
VEHICLE
CLIP
DIN HARNESS
TERMINAL
DVD PLAYER
i-VES
HARNESS
TERMINAL
COIN POCKET
HOLDER
MAIN HARNESS
4-PIN CONNECTOR
VEHICLE
CONNECTOR
2N21121S
2D11020S
71. Insert the studs of the upper and lower player
brackets into the holes in the right and left player
brackets while pushing down on the lid of the coin
pocket holder as shown; then install one 6 mm
flange nut on the end of each stud, and tighten.
With an Ashtray Holder:
SELF-TAPPING
SCREW
(reused)
MASKING
TAPE
VEHICLE
CONNECTOR
VEHICLE
CLIP
LEFT
6 mm
PLAYER FLANGE
BRACKET NUTS (4)
RIGHT PLAYER
BRACKET
STUD
PLAYER
ASHTRAY
HOLDER
ILLUMINATION
BULB
CIGARETTE
LIGHTER HARNESS
2-PIN CONNECTOR
3305021S
STUD
Push down
on the lid
of the coin
pocket
holder.
2031292S
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
BII 28366 (0410)
17 of 18
72. Insert two player panel hooks into the square
holes of the right and left player brackets, then
insert the two player panel clips into the latches.
SQUARE HOLE
HOOK
CLIP
PLAYER
PANEL
2031301S
LATCH
73. Remove the masking tape applied in steps 54 and
69.
74. Check that all wire harnesses are routed properly,
and all connectors are plugged in.
75. Reconnect the negative cable to the battery.
76. Enter the customer’s navigation system, if
equipped, radio anti-theft codes, and reset the
radio station presets.
77. Set the clock.
78. Check the operation of the in-vehicle
entertainment system according to the Owner’s
Manual supplied with the kit.
79. Put the Owner's Manual for the in-vehicle
entertainment system in the glove box with the
vehicle owner's manual.
80. Reinstall all removed parts.
18 of 18
BII 28366 (0410)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement