AD6
Manual en Español Latino Americano:
http://www.schwinnfitness.com
ASSEMBLY MANUAL / OWNER’S MANUAL
TABLE OF CONTENTS
Important Safety Instructions - Assembly
3
Safety Warning Labels / Serial Number
4
Specifications
5
Before Assembly
5
Parts6
Hardware7
Tools7
Assembly8
Moving the Machine
13
Leveling the Machine
13
Important Safety Instructions 14
Features
15
Console Features
16
Remote Heart Rate Monitor
17
Operations18
Adjustments
18
Using the Machine
18
Locking the Fan Assembly / Storage
19
Power Up / Idle Mode
19
Initial Setup
20
Quick Start Program
20
Custom Time Workout
20
Pausing or Stopping
20
Results Mode
20
Console Service Mode
21
Maintenance22
Replacing the Console Batteries
23
Maintenance Parts
24
Troubleshooting
25
Warranty27
To validate warranty support, keep the original proof of purchase and record the following information:
Serial Number __________________________
Date of Purchase ____________________
To register your product warranty , go to: www.SchwinnFitness.com/register
Or call 1 (800) 605–3369.
If you have questions or problems with your product, please call 1 (800) NAUTILUS (628–8458).
Nautilus, Inc., (800) NAUTILUS / (800) 628-8458, www.NautilusInc.com - Customer Service: North America (800) 605-3369, csnls@
nautilus.com | outside U.S. +01-360-859-5180, technics@nautilus.com | Printed in China | © 2012 Nautilus, Inc.
2
IMPORTANT SAFETY INSTRUCTIONS - ASSEMBLY
This icon means a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Obey the following warnings:
Read and understand all warnings on this machine.
Carefully read and understand the Assembly instructions.
• Keep bystanders and children away from the product you are assembling at all times.
• Do not install the batteries into the machine until the time specified in the assembly manual.
• Do not assemble this machine outdoors or in a wet or moist location.
• Make sure assembly is done in an appropriate work space away from foot traffic and exposure to bystanders.
• Some components of the machine can be heavy or awkward. Use a second person when doing the assembly steps
involving these parts. Do not do steps that involve heavy lifting or awkward movements on your own.
• Set up this machine on a solid, level, horizontal surface.
• Do not try to change the design or functionality of this machine. This could compromise the safety of this machine and
will void the warranty.
• If replacement parts are necessary use only genuine replacement parts and hardware supplied by Nautilus. Failure
to use genuine replacement parts can cause a risk to users, keep the machine from operating correctly and void the
warranty.
• Do not use or put the machine into service until the machine has been fully assembled and inspected for correct
performance in accordance with the Manual.
• Read and understand the complete Manual supplied with this machine before first use. Keep the Manual for future
reference.
• Do all assembly steps in the sequence given. Incorrect assembly can lead to injury or incorrect function.
• This product contains magnets. Magnetic fields can interfere with the normal use of certain medical devices at a close
range. Users may come into proximity of the magnets in the assembly, maintenance, and/or use of the product. Given
the obvious importance of these devices, such as a pacemaker, it is important that you consult with your medical
provider in connection with the use of this equipment. Please consult the “Safety Warning Labels and Serial Number”
section to determine the location of the magnets on this product.
3
SAFETY WARNING LABELS AND SERIAL NUMBER
Serial number
Product specification
4
SPECIFICATIONS
Machine Weight: 115 lbs. (52.2 kg)
Power Requirements: Operating Voltage: 2 AA Batteries
1.0 - 3.3VDC
Maximum User Weight: 300 lbs. (136 kg)
50.9”
(129.2 cm)
Regulatory Approvals: 49.7”
(126.3 cm)
25.7”
(65.2 cm)
This product conforms to the applicable EN ISO 20957 International Standards for Stationary Training Equipment, Class S
DO NOT dispose of this product as refuse. This product is to be recycled. For information on the proper method of
disposal, contact a Nautilus Customer Service Representative. Contact information is available in the Contacts
section in this manual.
This product, its packaging, and components contain chemicals known to the State of California to cause cancer,
birth defects, or reproductive harm. This Notice is provided in accordance with California’s Proposition 65. If you
would like additional information, please refer to our website at www.nautilus.com/prop65.
Before Assembly
8/6/2014
Select the area where you are going to set up and operate your machine. For safe operation, the location must be on a
hard, level surface. Allow a workout area of a minimum 73.7” (187.2 cm) x 97.7” (248.2 cm).
Basic Assembly Tips
Follow these basic points when you assemble your machine:
• Read and understand the “Important Safety Instructions” before assembly.
• Collect all the pieces necessary for each assembly step.
• Using the recommended wrenches, turn the bolts and nuts to the right (clockwise) to tighten, and the left (counterclockwise) to loosen, unless instructed otherwise.
• When attaching 2 pieces, lightly lift and look through the bolt holes to help insert the bolt through the holes.
• The assembly requires 2 people.
5
PARTS
4
16
6
17
3
7
5
2
STO
P
15
8
R
14
13
1
9
12
10
11
A decal has been applied to all right (“ R ”) and left (“ L ”) parts to assist with assembly.
Item
Qty
1
1
2
6
Description
Item
Qty
Description
Frame
10
1
Pedal, Left
1
Console Support Bar
11
1
Foot Peg, Left
3
1
Console
12
1
Stabilizer, Front
4
1
Water Bottle Holder
13
1
Foot Peg, Right
5
1
Handlebar, Left
14
1
Pedal, Right
6
1
Seat
15
1
Pedal Strap, Right
7
1
Seat Post
16
1
Handlebar, Right
8
1
Stabilizer, Rear
17
1
Strap, Transport and Immobilization
9
1
Pedal Strap, Left
HARDWARE / TOOLS
A
Item
Qty
A
4
B
C
B
C
Description
D
E
Item
Qty
Description
Button Head Hex Screw, M8x1.25x20
D
4
Washer, M8 Black
4
Washer, M8 Lock
E
4
Button Head Hex Screw, M8x1.25x12
Black
4
Washer, M8
Tools
Included Not Included
6 mm
2 AA size batteries (LR6)
(recommended)
#2
13 mm
15 mm
17 mm
7
ASSEMBLY
1. Attach Stabilizers to Frame
Note: Hardware is pre-installed and not on the Hardware Card ( * ).
6mm
X4
*
8
*
1
12
15
14
R
9
2. Attach Pedals and then Pedal Straps to Frame Assembly
Note: The Left Pedal is reverse-threaded. Be sure to attach Pedals on the proper side of the Bike. Orientation is based from
a seated position on the bike. The Left Pedal has an “L”, the Right Pedal an “R”.
15
14
R
9
10
10
X2
X2
8
3. Connect Cables and Attach the Console Support Bar to Frame Assembly
Note: Do not crimp the cables. Pull the lower cable to remove any slack as you insert the Console Support Bar.
In order to avoid possible serious injury, when inserting the tube ends into the Frame Assembly be careful to avoid
fingers or hands being caught or pinched.
2
X4
6mm
E
D
4. Remove Hardware and Install Batteries into Console
Note: Make sure that the batteries point in the direction of the +/– indicators in the battery bay. Hardware is pre-installed
and not on the Hardware Card ( * ).
Do not mix alkaline, standard (carbon-zinc), or rechargeable (Ni-Cd, Ni-MH, etc) batteries.
3
*
X4
#2
9
5. Connect Cable and Attach the Console
Note: Do not crimp Console Cable.
X4
*
#2
X4
*
#2
6. Attach Water Bottle Holder to Frame Assembly
Note: Hardware is pre-installed and not on the Hardware Card ( * ).
#2
X2
*
10
4
7. Attach Foot Pegs and Handlebar Arms to Frame Assembly
5
16
11
X4
C
13
8. Loosen and Pull the Seat Post Adjustment Knob to Attach Seat Post to
Frame Assembly
B
A
6mm
7
STO
P
11
9. Attach Seat to Seat Post
NOTICE: Be sure the Seat is straight and then tighten the hardware.
6
10. Final Inspection
Inspect your machine to ensure that all hardware is tight and components are properly assembled.
Do not use or put the machine into service until the machine has been fully assembled and inspected for correct
performance in accordance with the Owner’s Manual.
12
BEFORE YOU START
Moving the Machine
The machine may be moved by one or more persons depending on their physical abilities and capacities. Make sure
that you and others are all physically fit and able to move the machine safely. Use proper safety precautions and
lifting techniques.
1.Secure the Handlebar to the Console Support Bar with the
Transport and Immobilization Strap (T).
2.Use the Rear Stabilizer to carefully lift the machine onto the
transport rollers.
T
Note: Be sure to keep the fan assembly clear of the floor.
3.Push the machine into position.
4.Carefully lower the machine into position.
NOTICE: B
e careful when you move the machine. All abrupt
motions can affect the computer operation.
Leveling the Machine
The machine needs to be leveled if your workout area is uneven. To adjust:
1.Place the machine in your workout area.
2. Loosen the locking nuts and adjust the levelers until they are evenly balanced and in contact with the floor.
Do not adjust the levelers to such a height that
they detach or unscrew from the machine. Injury to
you or damage to the machine can occur.
3.Tighten the locking nuts.
Make sure the machine is level and stable before you
exercise.
13
IMPORTANT SAFETY INSTRUCTIONS
This icon means a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Before using this equipment, obey the following warnings:
Read and understand the complete Manual. Keep the Manual for future reference.
ead and understand all warnings on this machine. If at any time the Warning stickers become loose, unreadable or
R
dislodged, contact Nautilus® Customer Service for replacement stickers.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Children must not be let on or near to this machine. Moving parts and other features of the machine can be dangerous
to children.
Not intended for use by anyone under 14 years of age.
Consult a physician before you start an exercise program. Stop exercising if you feel pain or tightness in your
chest, become short of breath, or feel faint. Contact your doctor before you use the machine again. Use the values
calculated or measured by the machine’s computer for reference purposes only.
Before each use, examine this machine for loose parts or signs of wear. Do not use if found in this condition. Monitor
the Pedals and Crank Arms closely. Contact Nautilus® Customer Service for repair information.
Maximum user weight limit: 300 lbs. (136 kg). Do not use if you are over this weight.
This machine is for Home and Light Commercial use only. Light Commercial use is defined as settings where usage is
less than 5 hours per day in non-dues-paying facilities—for example, condominiums, hotels and corporate gyms.
Do not wear loose clothing or jewelry. This machine contains moving parts. Do not put fingers or other objects into
moving parts of the exercise equipment.
Set up and operate this machine on a solid, level, horizontal surface.
Do not step off the machine until the Pedals have fully stopped.
Make the Pedals stable before you step on them. Use caution when you step on and off the machine.
Do not operate this machine outdoors or in moist or wet locations.
Keep at least 24” (0.6 m) on each side of the machine clear. This is the recommended safe distance for access and
passage around and emergency dismounts from the machine. Keep third parties out of this space when machine is in
use.
Do not over exert yourself during exercise. Operate the machine in the manner described in this manual.
Perform all regular and periodic maintenance procedures recommended in the Owner’s Manual.
Correctly adjust and safely engage all Positional Adjustment Devices. Make sure that the Adjustment Devices do not
hit the user.
Keep the Pedals clean and dry.
Exercise on this machine requires coordination and balance. Be sure to anticipate that changes in speed and
resistance level can occur during workouts, and be attentive in order to avoid loss of balance and possible injury.
Keep batteries away from heat source and hot surfaces.
Do not drop or put objects into any opening of the machine.
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc), or rechargeable (Ni-Cd, Ni-MH, etc) batteries.
•
For safe storage of the machine, remove the batteries and install the Transport and Immobilization Strap to secure the
Resistance Fan. Place the machine in a secure location from children and pets.
•
When the machine is put in a Light Commercial environment, it can only be used in areas where access and control of
the machine is managed by approved staff. The degree of management depends among other things on the specific
setting in which the machine is placed, security of that environment, and familiarity of the users with the equipment.
•
This bike cannot stop the Pedals independently of the Resistance Fan. Reduce the pace to slow the Resistance Fan
and Pedals to a stop. Do not dismount the bike until the Pedals have come to a complete stop.
14
FEATURES
B
A
C
D
P
O
E
F
N
M
G
H
L
K
I
J
A
Console
G
Air Resistance Fan
M
Stabilizer, Rear
B
Hand Grip
H
Transport Roller
N
Foot Step Pad
C
Handlebar
I
Leveler
O
Seat Post Adjustment Knob
D
Water Bottle Holder
J
Stabilizer, Front
P
Seat
E
Battery Compartment
K
Foot Peg
F
Transport and Immobilization
Strap
L
Pedal
S
Remote Heart Rate Chest Strap
R
S
Q
Accessories
Q
AirDyne® Reading Rack
R
AirDyne® Wind Screen
To order, go to www.schwinnfitness.com or call 1 (800) 605-3369.
15
Console Features
The Console provides information about your workout on the display screen.
LCD Display Data
The console display shows each workout value.
RPM
The RPM display field shows the machine revolutions per minute (RPM).
The maximum display is 100.
Time
The TIME display field shows the time count of the workout. The maximum display is 99:59. If the time count is more, the display starts again at
0:00.
During the initial power-up, this display will show altitude ( “Alt“ ). The
altitude where the machine will be in operation must be entered.
Speed
The SPEED display field shows the machine speed in kilometers per hour
( “KM” ) or miles per hour ( “M” ), to one decimal place—for example, 3.4
or 10.5. The maximum display is 99.9.
Dist.
The DISTANCE display field shows the distance count (miles or km) in
the workout, to two decimal places—for example, 2.07. The maximum
display is 99.99. If the distance exceeds 99.99, the display starts again at
0.00.
Decrease
Note: T
o change the measurement units to English Imperial or metric,
refer to the “Console Service Mode” section in this manual.
START/STOP
Increase
The Odometer ( “Odo.” ) shows the sum of all workout distances. It is displayed when a workout is paused, or as an option in the “Console Service
Mode”.
During the initial power-up, this display will show the Altitude value until accepted.
Watts
The WATTS display field shows the power that you are producing at the current resistance level (1 horsepower = 746
watts).
Calories
The CALORIES display field shows the estimated calories that you have burned during the exercise. The maximum
display is 9999. If the calorie count is more, the display flashes 9999.
Pulse
The PULSE display shows the heart rate in beats per minute (BPM) from a telemetric heart rate sensor. The icon will flash
when it has a signal from a telemetric heart rate strap. This display value will be blank if a heart rate signal is not detected.
Consult a physician before you start an exercise program. Stop exercising if you feel pain or tightness in your chest,
become short of breath, or feel faint. Contact your doctor before you use the machine again. The heart rate
displayed is an approximation and should be used for reference purposes only.
Keypad Functions
Decrease () button- Decreases a value (time or altitude) or moves through options
16
START/STOP button- Starts a Program workout, confirms a selection, and ends a paused workout if held down for 3
seconds.
Increase () button-
Increases a value (time or altitude) or moves through options
Remote Heart Rate Monitor
Monitoring your Heart Rate is one of the best procedures to control the intensity of your exercise. The Console can read
telemetry HR signals from a Heart Rate Chest Strap Transmitter that operates in the 4.5kHz - 5.5kHz range.
Note: T
he heart rate chest strap must be an uncoded heart rate strap from Polar Electro or an uncoded POLAR® compatible model. (Coded POLAR® heart rate straps such as POLAR® OwnCode® chest straps will not work with this
equipment.)
If you have a pacemaker or other implanted electronic device, consult your doctor before using a wireless chest
strap or other telemetric heart rate monitor.
Heart Rate Calculations
Your maximum heart rate usually decreases from 220 Beats Per Minute (BPM) in childhood to approximately 160 BPM by
age 60. This fall in heart rate is usually linear, decreasing by approximately one BPM for each year. There is no indication
that training influences the decrease in maximum heart rate. Individuals of the same age could have different maximum
heart rates. It is more accurate to find this value by completing a stress test than by using an age related formula.
Your at-rest heart rate is influenced by endurance training. The typical adult has an at-rest heart rate of approximately 72
BPM, where as highly trained runners may have readings of 40 BPM or lower.
The Heart Rate table is an estimate of what Heart Rate Zone (HRZ) is effective to burn fat and improve your cardiovascular system. Physical conditions vary, therefore your individual HRZ could be several beats higher or lower than what is
shown.
The most efficient procedure to burn fat during exercise is to start at a slow pace and gradually increase your intensity until your heart rate reaches between 60 – 85% of your maximum heart rate. Continue at that pace, keeping your heart rate
in that target zone for over 20 minutes. The longer you maintain your target heart rate, the more fat your body will burn.
The graph is a brief guideline, describing the generally suggested target heart rates based on age. As noted above, your
optimal target rate may be higher or lower. Consult your physician for your individual target heart rate zone.
Note: As with all exercises and fitness regimens, always use your best judgment when you increase your exercise
time or intensity.
FAT-BURNING TARGET HEART RATE
Heart Rate BPM (beats per minute)
250
200
196
167
191
162
186
181
158
154
150
100
118
115
112
109
176
150
106
171
166
145
141
103
100
161
137
97
156
133
94
151
128
91
146
126
88
50
0
20-24 25-29 30-34 35-39 40-44 45-49 50-54 55-59 60-64 65-69
70+
Age
Maximum Heart Rate
Target Heart Rate Zone
(keep within this range
for optimum fat-burning)
17
OPERATIONS
What to Wear
Wear rubber-soled athletic shoes. You will need the appropriate clothes for exercise that allow you to move freely.
How Often Should You Exercise
Consult a physician before you start an exercise program. Stop exercising if you feel pain or tightness in your chest,
become short of breath, or feel faint. Contact your doctor before you use the machine again. Use the values
calculated or measured by the machine’s computer for reference purposes only. The heart rate displayed is an
approximation and should be used for reference purposes only.
• 3 times a week for 20 minutes each day.
• Schedule workouts in advance and try to follow the schedule.
Seat Adjustment
Correct seat placement encourages exercise efficiency and comfort, while reducing the risk of
injury.
1.With a Pedal in the forward position, place the heel of your foot to the lowest part of it. Your
leg should be bent slightly at the knee.
2.If your leg is too straight or your foot cannot touch the Pedal, you need to move the seat
downward. If your leg is bent too much, you need to move the seat upward.
Step off the machine before you adjust the seat.
3.
Loosen and pull the Seat Post Adjustment Knob on the Seat Post. Adjust the seat to the
desired height.
Do not lift the Seat post above the “STOP” mark on the Seat Post.
4.
Release the Seat Post Adjustment Knob to engage the locking pin. Be sure that the pin is fully engaged and fully
tighten the adjustment knob.
Foot Position / Pedal Strap Adjustment
Foot pedals with straps provide secure footing to the exercise bike.
1.Rotate the Pedals until one can be reached.
Be aware that the Pedals, Handlebars and Resistance Fan are connected and when any
of these parts move the others do as well.
2.Put the ball of each foot on the Pedals.
3.Fasten the strap over the shoe.
4.Repeat for the other foot.
Be sure toes and knees point directly forward to ensure maximum Pedal efficiency. Pedal straps
can be left in position for subsequent workouts.
Using the Machine
Be aware that the Pedals, Handlebars and Resistance Fan are connected and when any of these parts move the
others do as well.
Carefully mount the machine using the Foot Step Pad if necessary. Adjust the Seat and Pedals before starting a workout.
Lower Body Workout: Slowly pedal with your arms relaxed at your sides or with your hands resting on the Hand Grips as
the Handlebars move.
18
Full Body Workout: Grasp the Hand Grips with your palms down. Push and pull the Handlebars as you pedal, keeping
your elbows low and next to your body.
Upper Body Workout: Grasp the Hand Grips firmly with palms down and place your feet on the Foot Pegs. Lean slightly
forward at the hips with your back straight and shoulders down. Now push and pull the Handlebars
Note: You may need to safely push a Pedal to assist with starting the workout.
To increase the air resistance and workload, increase your level of activity. To exercise all the muscle groups in your arms,
alter your grasp to palms up for part of the workout.
When done with your workout, reduce the Resistance Fan speed until the machine fully stops.
This bike cannot stop the Pedals independently of the Resistance Fan. Reduce the pace to slow the Resistance Fan
and Pedals to a stop. Do not dismount the bike until the Pedals have come to a complete stop.
Locking the Fan Assembly / Storage
When the machine is not in use, be sure to lock the Fan Assembly with the Transport and Immobilization Strap. The fan
assembly should be locked for storage of the machine.
For safe storage of the machine, remove the batteries and
install the Transport and Immobilization Strap to secure the
Resistance Fan. Place the machine in a secure location
from children and pets. Be aware that the Pedals, Handlebars and Resistance Fan are connected and when any of
these parts move the others do as well.
T
To lock the Fan Assembly:
1.Move the Handlebars so that one Handlebar is as close as
possible to the Console Support Bar.
2.Wrap the Transport and Immobilization Strap (T) around the
Handlebar and the Console Support Bar and put the end of
the strap through the metal ring. Tighten the strap to prevent
movement of the handlebars and secure the strap.
Power-Up / Idle Mode
The Console will enter Power-Up / Idle Mode if any button is pushed, or if it receives a signal from the RPM sensor as a
result of pedaling the machine.
Note: The Console will display “Lbatt” if the batteries are around 10% of their rated power during power up.
Auto Shut-Off (Sleep Mode)
If the Console does not receive any input in approximately 5 minutes, it will automatically shut off. The LCD display is off
while in Sleep Mode.
Note: The Console does not have an On/Off switch.
19
Initial Setup
During the initial power-up, the Console will display “Alt” and must be setup with the current workout altitude.
1. Push the Increase/Decrease buttons to change the value for the altitude. Entering the correct value will make the
calorie count more accurate.
2. Push the START/STOP button to set.
Note: The altitude value can be adjusted at a future time. To adjust the value, consult the “Console Set-Up Mode” section.
Quick Start Workout
The Quick Start program lets you start a workout without entering any information.
1. Sit on the machine.
2. With the Console in Idle Mode, push the START/STOP button to start the workout program.
3.When done with your workout, stop pedaling. Then push and hold down the START/STOP button for 3 seconds to
end the workout.
Custom Time Workout
The Console allows you to select a Custom Time Workout and enter your own time value. The Console will remember this
value until changed.
1. Sit on the machine.
2. With the Console in Idle Mode, push and hold down for 3 seconds the START/STOP button.
3.The Console will show the default value or the last custom time value.
Note: The default time value is 20 minutes.
4. Push the Increase and Decrease buttons to adjust the custom time value.
5. Push START/STOP to accept the custom time workout. Your Custom Goal Workout will now begin.
Pausing or Stopping
To Pause a workout:
1. Stop pedaling to pause your workout.
Note: The Console will automatically pause if there is no RPM signal for 5 seconds.
2. To continue your workout, push START/STOP or start pedaling.
o stop the workout, push and hold down the START/STOP button for 3 seconds. The Console will go into Results
T
mode.
When paused, the Console display will flash the current workout values of TIME, AVERAGE SPEED, DISTANCE, TOTAL
MACHINE DISTANCE (“Odo.”), WATTS, CALORIES, and AVERAGE HEART RATE (if activated).
Results Mode
When you complete or end a workout, the Console will display your workout values three times in the order of TIME, AVERAGE SPEED, DISTANCE, WATTS, CALORIES, and AVERAGE HEART RATE (if activated).
Push START/STOP to stop the Results display and go back to Idle Mode.
20
CONSOLE SERVICE MODE
The Console Service Mode lets you set the units of measurement to either English or Metric, see the total time and
distance the machine has been used, adjust the altitude value for a more accurate calorie count, or find out which version
of Firmware is installed.
1.Hold down the Increase button and Decrease button together for 3 seconds while in the Idle Mode to go into the Console Service Mode.
2.The Console display shows the Units prompt ( “Unit” ). Push START/STOP to start Units option. Push the Increase/
Decrease buttons to change between “M” (Imperial English units) and “KM” (metric units).
3. Push START/STOP to set. For the next option, push the Increase button.
4.The Console display shows the Workout Statistics prompt ( “StAt” ). Push START/STOP to start the Workout Statistics
option. The Console will display the Total Distance ( “Odo” ) and Total Time.
Note: The upper displayed value is total hours followed by the remaining minutes.
5. Push START/STOP to exit. For the next option, push the Increase button.
6.The Console display shows the Firmware Version prompt ( “Fir” ). The Console will display which Firmware Version is
installed in the Speed display field.
7. For the next option, push the Increase button.
8. T
he Console display shows Altitude ( “Alt” ) with the previously entered value in the Speed display field. Push START/
STOP to adjust the Altitude value. Use the Increase/Decrease buttons to change the value.
9. Push START/STOP to exit. For the next option, push the Increase button.
10. The Console display shows the exit prompt ( “dOnE” ).
11. Push START/STOP to exit.
To fully exit the Console Service Mode push and hold down the START/STOP button for 3 seconds. In Service Mode if the
Console does not receive any input in approximately 5 minutes, it goes into Sleep Mode.
21
MAINTENANCE
Read all maintenance instructions fully before you start any repair work. In some conditions, an assistant is required to do
the necessary tasks.
Equipment must be regularly examined for damage and repairs. The owner is responsible to make sure that regular
maintenance is done. Worn or damaged components must be repaired or replaced immediately. Only manufacturer
supplied components can be used to maintain and repair the equipment.
Daily:
Before each use, examine the exercise machine for loose, broken,
damaged, or worn parts. Do not use if found in this condition. Repair
or replace all parts at the first sign of wear or damage. After each
workout, use a damp cloth to wipe your machine and Console free of
sweat.
Note: Avoid excessive moisture on the Console.
Weekly:
Clean the machine to remove any dust, dirt, or grime from the surfaces.
Check for smooth seat operation. If needed, sparingly apply a thin
coating of silicone lube to ease operation.
Note: Do not use petroleum based products.
Monthly
or after 20
hours:
22
Check pedals, crank arms and handlebars. Make sure all bolts and
screws are tight. Tighten as necessary.
NOTICE: D
o not clean with a petroleum based solvent or an automotive cleaner. Be sure to keep the Console
free of moisture.
hen the machine is used in a Light Commercial environment, the Pedals must be replaced every year to
W
maintain maximum user safety and performance. Only use replacement Pedals available from Nautilus.
Other brands of Pedals may not be designed for Indoor Cycling and can cause danger to users and
bystanders.
Replacing the Console Batteries
The Console will display “Lbatt” for ten seconds when the batteries are around 10% of their rated power during power up.
When replacing the batteries, make sure the batteries point in the +/- direction shown in the battery bay.
Note: The console uses AA size batteries (LR6).
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc), or rechargeable (Ni-Cd, Ni-MH, etc) batteries.
23
Maintenance Parts
E
F
K
H
G
C
L
B
JJ
KK
J
M
S
N
A
II
O
D
P
EE
HH
CC
BB
AA
FF
GG
Q
Z
R
S
T
DD
Y X
W V
U
A
Foot Peg, Right
N
Seat Adjustment Knob
AA
Connector Arm
B
Handlebar, Right
O
Frame
BB
Arm Pivot
C
Handlebar, Left
P
Stabilizer, Rear
CC
Console Cable, Lower
D
Foot Peg, Left
Q
Shroud, Left
DD
Resistance Fan Assembly
E
Water Bottle Holder
R
Crank Arm, Left
EE
Fan Cover
F
Console
S
Center Plate
FF
Leveler
G
Strap, Transport/Immobilization
T
Pedal, Left
GG
Stabilizer, Front
H
Console Support Bar
U
Pulley, Crank
HH
Transport Wheel
I
not used
V
Speed Sensor Magnet
II
Shroud, Right
J
Console Cable, Upper
W
Crank Belt
JJ
Crank Arm, Right
K
Seat
X
Pulley, Drive
KK
Pedal, Right
L
Seat Post
Y
Drive Belt
M
Foot Step Pad
Z
Speed Sensor Assembly
24
TROUBLESHOOTING
Condition/Problem
Things to Check
Console will not power up/ Batteries
turn on/start
Solution
Make sure batteries are installed correctly. If batteries are
correctly installed, replace with a set of new batteries.
Check data cable integrity
All wires in cable should be intact. If any are visibly crimped or
cut, replace cable.
Check data cable
connections/orientation
Make sure cable is connected securely and oriented properly.
Small latch on connector should line up and snap into place.
Check console display for
damage
Check for visual sign that console display is cracked or
otherwise damaged. Replace Console if damaged.
If the above steps do not resolve the problem, contact
Customer Care for further assistance.
Speed displayed is not
accurate
Display set to wrong unit
of measure. (English/
Metric)
Speed displayed is always Data cable
“0”/stuck in Pause mode
Change display units (consult “Console Service Mode”)
Make sure the data cable is connected to the back of the
Console and the main frame assembly.
Speed Sensor (under
Shrouds)
Make sure the Speed Sensor Magnet and the Speed Sensor
are in place.
Check data cable integrity
All wires in cable should be intact. If any are cut or crimped,
replace cable.
Check data cable
connections/orientation
Be sure cable is connected securely and oriented properly.
Small latch on connector should line up and snap into place.
Check Speed Sensor
Magnet position (requires
shroud removal)
Magnet should be in place on pulley.
Check Speed Sensor Assembly (requires shroud
removal)
Speed Sensor Assembly should be aligned with magnet and
connected to data cable. Realign sensor if necessary. Replace
if there is any damage to the sensor or the connecting wire.
Console displays “Lbatt”
error code
Batteries
Replace batteries
Unit operates but Telemetric Heart Rate not
displayed
Chest Strap (optional)
Strap should be “POLAR®” compatible and uncoded. Make
sure strap is directly against skin and contact area is wet.
Interference
Try moving unit away from sources of interference (TV, Microwave, etc).
Replace Chest Strap
If interference is eliminated and HR does not function, replace
strap.
Replace Console
If HR still does not function, replace Console.
Check data cable integrity
All wires in the cable should be intact. If any are cut or crimped,
replace cable.
Check data cable
connections/orientation
Be sure cable is connected securely and oriented properly.
Small latch on connector should line up and snap into
place.
Check Speed Sensor
Magnet position (requires
shroud removal)
Speed Sensor Magnet should be in place on pulley.
Check Speed Sensor Assembly
Contact Customer Care for further assistance.
No speed/RPM reading
Console shuts off (enters
sleep mode) while in use
25
Unit rocks/does not sit
level
Pedals loose/unit difficult
to pedal
Check leveler adjustment
Leveling feet may be turned in or out to level bike.
Check surface under unit
Adjustment may not be able to compensate for extremely uneven surfaces. Move bike to level area.
Check pedal to crank con- Pedal should be tightened securely to crank. Be sure connecnection
tion is not cross-threaded.
Check crank to axle connection
Crank should be tightened securely to axle.
Clicking sound when
pedaling
Check pedal to crank con- Remove pedals and reattach fully.
nection
Seat post movement
Check locking pin
Be sure adjustment pin is locked into one of the seat post
adjustment holes.
Check locking knob
Be sure knob is securely tightened.
26
WARRANTY
Who Is Covered
This warranty is valid only to the original purchaser and is not transferable or applicable to any other person(s).
What Is Covered
Nautilus, Inc. warrants that this product is free from defects in materials and workmanship, when used for the purpose intended, under normal conditions, and provided it receives
proper care and maintenance as described in the Product’s Assembly and Owner’s manual. This warranty is good only for authentic, original, legitimate machines manufactured by
Nautilus, Inc. and sold through an authorized agent and used in the United States or Canada.
Terms
ResidentialLight Commercial
•
Frame
15 years
10 years
•
Mechanical parts 3 years 1 year
•
Electronics 2 years
1 year
•
Labor
6 months
3 months
(Labor support does not include the installation of replacement parts involved in the initial product assembly and preventative maintenance services.)
How Nautilus Will Support the Warranty
Throughout the terms of the warranty coverage, Nautilus, Inc. will repair any machine that proves to be defective in materials or workmanship. Nautilus reserves the right to replace
the product in the event a repair is not possible. When Nautilus determines replacement is the correct remedy, Nautilus may apply a limited credit reimbursement toward another
Nautilus, Inc. brand Product, at our discretion. This reimbursement may be prorated based on length of ownership. Nautilus, Inc. provides repair service within major metropolitan
areas. Nautilus, Inc. reserves the right to charge the consumer for travel outside these areas. Nautilus, Inc. is not responsible for dealer labor or maintenance charges beyond the
applicable warranty period(s) stated herein. Nautilus, Inc. reserves the right to substitute material, parts or products of equal or better quality if identical materials or products are
not available at the time of service under this warranty. Any replacement of the product under the terms of the Warranty in no way extends the original Warranty period. Any limited
credit reimbursement may be prorated based on length of ownership. THESE REMEDIES ARE THE EXCLUSIVE AND SOLE REMEDIES FOR ANY BREACH OF WARRANTY.
What You Must Do
•
Retain appropriate and acceptable Proof of Purchase.
•
Operate, maintain, and inspect the Product as specified in the Product Documentation (Assembly, Owner’s Manuals, etc.).
•
Product must be used exclusively for the purpose intended.
•
Notify Nautilus within 30 days after detecting an issue with the Product.
•
Install replacement parts or components in accordance with any Nautilus instructions.
•
Perform diagnostic procedures with a trained Nautilus, Inc representative if requested.
What Is Not Covered
•
Damage due to abuse, tampering or modification of the Product, failure to properly follow assembly instructions, maintenance instructions, or safety warnings as stated in the
Product Documentation (Assembly, Owner’s Manuals, etc), damage due to improper storage or the effect of environmental conditions such as moisture or weather, misuse,
mishandling, accident, natural disasters, power surges.
•
A machine placed or used in a commercial setting. This includes commercial gyms, clubs, fitness centers and any public or private entity that has a machine for use by its
members, customers, employees or affiliates where dues, subscriptions or paid memberships are collected, or where the product is used more than 5 hours per day.
•
Damage caused by exceeding maximum user weights as defined in the Product’s Owner’s manual or warning label.
•
Damage due to normal usage and wear and tear.
•
This warranty does not extend to any territories or countries outside the United States and Canada.
How to Obtain Service
For Products purchased directly from Nautilus, Inc. contact the Nautilus office listed on the Contacts page of the products Owner’s manual. You may be required to return the
defective component to a specified address for repair or inspection, at your expense. Standard ground shipping of any warranty replacement parts will be paid by Nautilus, Inc. For
products purchased from a retailer, you may be asked to contact your retailer for warranty support.
Exclusions
The preceding warranties are the sole and exclusive express warranties made by Nautilus, Inc. They supersede any prior, contrary or additional representations, whether oral or
written. No agent, representative, dealer, person or employee has the authority to alter or increase the obligations or limitations of this warranty. Any implied warranties, including
the WARRANTY OF MERCHANTABILITY and any WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, are limited in duration to the term of the applicable express warranty
provided above, whichever is longer. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Limitation of Remedies
EXCEPT AS OTHERWISE REQUIRED BY APPLICABLE LAW, THE PURCHASER’S EXCLUSIVE REMEDY IS LIMITED TO REPAIR OR REPLACEMENT OF ANY COMPONENT DEEMED BY
NAUTILUS, INC. TO BE DEFECTIVE UNDER THE TERMS AND CONDITIONS STATED HEREIN. IN NO EVENT WILL NAUTILUS, INC. BE LIABLE FOR ANY SPECIAL, CONSEQUENTIAL,
INCIDENTAL, INDIRECT OR ECONOMIC DAMAGES, REGARDLESS OF THE THEORY OF LIABILITY (INCLUDING, WITHOUT LIMITATION, PRODUCT LIABILITY, NEGLIGENCE OR OTHER
TORT) OR FOR ANY LOST REVENUE, PROFIT, DATA, PRIVACY OR FOR ANY PUNITIVE DAMAGES ARISING OUT OF OR RELATED TO THE USE OF THE FITNESS MACHINE EVEN IF
NAUTILUS, INC. HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THIS EXCLUSION AND LIMITATION SHALL APPLY EVEN IF ANY REMEDY FAILS OF ITS ESSENTIAL
PURPOSE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF CONSEQUENTIAL OR INCIDENTAL TYPE DAMAGES SO THE ABOVE LIMITATION MAY NOT APPLY TO
YOU.
State Laws
This warranty gives you specific legal rights. You may also have other rights, which vary from state to state.
Expirations
If the warranty has expired, Nautilus, Inc. may assist with replacements or repairs to parts and labor, but there will be a charge for these services. Contact a Nautilus® office for
information on post-warranty parts and services. Nautilus® does not guarantee availability of spare parts after expiration of warranty period.
International Purchases
If you purchased your machine outside of the United States consult your local distributor or dealer for warranty coverage.
27
EN
Nautilus®
004-4743.081514.E
Bowflex®
Schwinn® Fitness
Universal®