Acura 2010 TL (TECH MODEL) Remote Control Engine Starter Installation Instructions
Below you will find brief information for Remote Control Engine Starter 2010 TL (TECH MODEL). This device allows you to start your vehicle remotely, using the provided transmitter. You can start your engine from up to 100 m to 150 m away, as long as you have a direct line of sight to the vehicle. The engine will stop automatically if you open a door, open the hood, put the gear in any position other than Park, or insert the key into the ignition switch.
Advertisement
Advertisement
INSTALLATION
INSTRUCTIONS
PARTS LIST
Remote Control Engine Starter Unit Kit
P/N 08E91-TK4-200A
Transmitter
Accessory
REMOTE CONTROL
ENGINE STARTER
Application
2010 TL
(TECH MODEL)
Quick Start Guide
Publications No.
BII 42536
Issue Date
AUG 2009
Remote Control Engine Starter Attachment Kit
P/N 08E92-TK4-200A
Engine starter harness
Control unit
Control unit bracket
Antenna
3 Relays
Key ring
Protective tape
Caution label
21 Wire ties
6 Urethane tapes
Template
Fuse label
Accessory User’s Information Manual
A-Pillar clip
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
BII 42536 (0908)
08E92-TK4-2A00-91
1 of 21
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Flat-tip screwdriver
Small flat-tip screwdriver
Ratchet
10 mm and 12 mm Sockets
10 mm Combination wrench
Diagonal cutters
Isopropyl alcohol
Shop towel
Tape measure
Scissors
Rubber mallet
HDS (Honda Diagnostic System)
Masking tape
2 Pairs of needle nose pliers
Plastic Trim Tool (T/N SILTRIMTL10)
Heavy gloves
Illustration of the Engine Starter Installed in the
Vehicle
ANTENNA
3A
FUSES
ENGINE
STARTER
HARNESS
CONTROL UNIT
INSTALLATION
Client Information: The information in this installation
instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by
“do-it-yourselfers.”
NOTE: The antenna should be installed only if the ambient air temperature 15°C (60°F) or above.
1.
Make sure you have the anti-theft codes for the audio and navigation system (if equipped), then write down the audio presets.
40A
FUSE
BLOCK
3 RELAYS
862701AT
2 of 21
BII 42536 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
Setting the Control Unit
2.
Using a small flat-tip screwdriver, adjust the switches on the (accessory) control unit to the locations shown.
NOTE:
• The switches must be adjusted before the control unit is plugged in.
• If the switch setting is not correct, the remote engine starter will not operate correctly.
• If adjusting the switches with the control unit installed in the vehicle, touch the metal part of the screwdriver to any metal part of the vehicle to discharge any static electricity.
• If you change the switch settings with the unit connected, you must disconnect the unit, and then reconnect it before the settings change.
CONTROL
UNIT
3.
Using isopropyl alcohol on a shop towel, clean the control unit where the protective tape will attach.
Remove the adhesive backing, and attach the protective tape to the control unit over the switch opening.
CONTROL
UNIT
SMALL
FLAT-TIP
SCREW-
DRIVER
Discharge any static electricity.
PROTECTIVE
TAPE
SWITCH
OPENING
ADHESIVE
BACKING
Clean with isopropyl alcohol.
772505AS
4.
Lower the tilt lever and pull the steering wheel out.
Remove the two lower self-tapping screws and the lower screw.
SELF-TAPPING
SCREW
SWITCHES
SWITCHES
The switches must be adjusted before the control unit is plugged in.
TILT
LEVER
SET
SW:1 RR Junction unit ------------------- > OFF
SW:2 Trunk or Tailgate -------------------- > OFF
SW:3 Smart Entry --------------------------- > ON
SW:4 Horn or Buzzer Answerback ---- > OFF
SW:5 Trunk Main SW----------------------- > OFF
SW:6 Reserve--------------------------------- > OFF
925003AT
LOWER
SELF-TAPPING
SCREW
LOWER
SCREW
830618BT
5.
Turn the steering wheel as necessary to access each self-tapping screw, and remove the two selftapping screws.
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
BII 42536 (0908)
3 of 21
6.
Remove the upper steering column cover and the lower steering column cover:
• Starting with the left side, use a small flat-tip screwdriver to push in to release the tab, then push in on the side of the upper steering column cover in the area shown to release the rear tab.
• Shift the column covers to the right, and repeat the same procedure.
• Release the four hooks, and remove the upper steering column cover and the lower steering column cover.
Push.
UPPER STEERING
COLUMN COVER
2 HOOKS
7.
Open the hood, and remove the front engine cover
(four clips and two hooks).
4 CLIPS
2 HOOKS
LOWER STEERING
COLUMN COVER
Push.
2 REAR TABS
SMALL FLAT-TIP
SCREWDRIVER
(Push on tabs.)
830617BT
FRONT
ENGINE
COVER
HOOK
HOOK
831801BH
8.
Disconnect the negative cable from the battery.
4 of 21
BII 42536 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
9.
Remove the roof console:
• Open the sunglass holder, and remove two selftapping screws.
• Release the two clips, and pull the roof console toward you.
• Unplug the vehicle connectors to remove the roof console.
VEHICLE CONNECTORS
2 CLIPS
11. Remove the left sunvisor.
• Turn the left sunvisor toward the driver’s seat.
• Locate the slot in the sunvisor holder, and insert a flat-tip screwdriver into the slot. Push in and hold the retaining tab.
• While holding the retaining tab, rotate the visor toward the door to remove.
• Unplug the vanity mirror light connector.
NOTE: If the retaining tab did not stay pushed in, return the left sunvisor to its original position and repeat the steps above.
VANITY
MIRROR
LIGHT
CONNECTOR
ROOF
CONSOLE
SUNGLASS
HOLDER
(Open.)
2 SELF-TAPPING
SCREWS
830606BT
10. Turn the sunvisor holder 90°, and remove the two sunvisor holders.
Push and hold the retaining tab.
HOLDER
LEFT
SUNVISOR
SLOT
FLAT-TIP
SCREWDRIVER
Rotate towards the door.
FRONT
830652AT
Turn.
2 SUNVISOR
HOLDERS
830653AT
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
BII 42536 (0908)
5 of 21
12. Pull away the door opening trim from the left front
A-pillar trim.
DOOR OPENING
TRIM
LEFT FRONT A-PILLAR TRIM
CLIP
SHOP
TOWEL
15. Remove and discard the clip from the left front
A-pillar trim, and install a new A-pillar clip (supplied) on the left front A-pillar trim.
NEW A-PILLAR CLIP
FRONT
PILLAR
LEFT FRONT
A-PILLAR TRIM
25 mm
(1 in.)
CLIP
RUBBER
MALLET
CLIP (Discard.)
PIN
Strike perpendicularly to the vehicle.
830602BT
13. Using a rubber mallet and a shop towel, gently tap the left front A-pillar trim at the position shown to release the clip.
14. Pull away the door opening trim, and remove the left front A-pillar trim (one clip, and unplug the vehicle connector).
CLIP
LEFT FRONT
A-PILLAR TRIM
LEFT FRONT
A-PILLAR TRIM
830604AT
16. Remove the left dashboard side cover (four clips and four hooks).
VEHICLE
CONNECTOR
4 CLIPS
4 HOOKS
DOOR OPENING
TRIM
LEFT
DASHBOARD
SIDE COVER
830614BT
830603AT
6 of 21
BII 42536 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
17. Remove the driver’s dashboard under cover:
• Turn the knob counterclockwise.
• Release the two clips and one pin, then pull the driver’s dashboard under cover toward you.
• Unplug the vehicle connector, and release the harness clip to remove the driver’s dashboard under cover.
VEHICLE CONNECTOR
PIN
HARNESS
CLIP
19. Pull away the door opening trim, and remove the left kick panel (two clips).
2 CLIPS
DRIVER’S
DASHBOARD
UNDER COVER
2 CLIPS
KNOB
(Turn.)
830607AT
18. Remove the left front door sill trim (four clips and three retaining tabs).
DOOR OPENING
TRIM
LEFT KICK
PANEL
Installing the Antenna
20. Using scissors, cut out the template.
Cut out.
830609AT
4 CLIPS
TEMPLATE
SCISSORS
830619AT
FRONT
LEFT FRONT DOOR
SILL TRIM
3 RETAINING
TABS
830608AT
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
BII 42536 (0908)
7 of 21
21. Using masking tape, attach the template to the windshield. Align with the black ceramic as shown.
BLACK
CERAMIC
WINDSHIELD
23. Starting near the antenna end of the cable, wrap three urethane tapes around the antenna cable at the measurements shown.
ANTENNA
ANTENNA
CABLE
400 mm
(16 in.)
Align with the black ceramic.
3 URETHANE TAPES
50 mm
(2 in.)
750 mm
(30 in.)
40 mm
(1.6 in.)
40 mm
(1.6 in.)
MASKING
TAPE
TEMPLATE
830620AT
22. Get the antenna. Bend the antenna plate according to the full scale drawing shown. Use two pairs of needle nose pliers as shown.
ANTENNA CABLE
URETHANE
TAPE
(Cut in half.)
2 HALF URETHANE TAPES
830622AT
24. Using scissors, cut one urethane tape in half. Wrap the two halves of the urethane tape around the antenna cable at the measurements shown.
ANTENNA
ANTENNA
PLATE
12 mm
(0.47 in.)
7 mm
(0.28 in.)
25 mm
(0.98 in.)
2 PAIRS OF
NEEDLE
NOSE
PLIERS
SCALE
8 of 21
830621BT
BII 42536 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
25. Using isopropyl alcohol on a shop towel, clean the area where the antenna will attach.
HEADLINER
WINDSHIELD
(Clean with isopropyl alcohol.)
ANTENNA
PLATE
TEMPLATE
29. Using isopropyl alcohol on a shop towel, clean the area where the urethane tapes will attach.
URETHANE
TAPE
(Cut in half.)
2 HALF
URETHANE
TAPES
ANTENNA
CABLE
ADHESIVE
BACKING
(Remove.)
ANTENNA
830623AT
26. Remove the adhesive backing from the antenna.
Insert the antenna plate over the headliner, align the antenna with the template, and attach it to the windshield.
• Make sure the antenna attaches firmly to the windshield.
27. Remove the template.
28. Route the antenna cable towards the driver’s side of the vehicle. Gently pull down the headliner, and tuck the antenna cable under it. Be careful not to crease the headliner.
ROOF PANEL
(Clean with isopropyl alcohol.)
830625AT
30. Using scissors, cut one urethane tape in half. Secure the antenna cable to the roof panel with the two halves of urethane tape.
31. Secure the antenna cable to the vehicle harness with six wire ties.
6 WIRE TIES
ANTENNA
CABLE
HEADLINER
VEHICLE
HARNESS
830626AT
ANTENNA
CABLE
830624BT
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
BII 42536 (0908)
9 of 21
32. Pull away the door opening trim from the left front
A-pillar. Route the antenna cable down next to the dashboard, and tuck the antenna cable between the left front A-pillar and the dashboard. Reinstall the door opening trim.
Routing the Engine Starter Harness
34. Using isopropyl alcohol on a shop towel, clean the area where the fuse label will attach.
DOOR OPENING TRIM
ENGINE
STARTER
HARNESS
FUSE CASE
3A FUSE
LABEL
DASHBOARD
LEFT FRONT
A-PILLAR
ANTENNA CABLE
830627BT
33. Route the antenna cable along the vehicle harness as shown.
ANTENNA
CABLE
Clean with isopropyl alcohol.
862702AT
35. Attach the 3A fuse label to the engine starter harness fuse case.
36. Using isopropyl alcohol on a shop towel, clean the area where the fuse labels will attach.
3A FUSE LABEL
Clean with isopropyl alcohol.
ENGINE
STARTER
HARNESS
40A
FUSE
LABEL
FUSE BLOCK
VEHICLE
HARNESS
830628CT
RELAY
BLOCK
3 RELAYS
862703AT
37. Attach the 40A and 3A fuse labels to the engine starter harness fuse block.
38. Install the three relays on the engine starter harness relay block.
10 of 21
BII 42536 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
39. Plug the antenna terminal into the control unit.
CONTROL UNIT
42. Attach the engine starter harness relay and fuse blocks onto the control unit bracket.
ENGINE
STARTER
HARNESS
RELAY
BLOCK
CLIP
CONTROL UNIT
BRACKET
ANTENNA
TERMINAL
ENGINE STARTER
HARNESS 28-PIN
CONNECTOR
830631AT
40. Plug the engine starter harness 28-pin connector into the control unit.
41. Install the control unit bracket to the control unit.
CONTROL UNIT
BRACKET
FUSE
BLOCK
862704AT
43. Remove the vehicle nut from the vehicle bracket, and secure the control unit bracket to the vehicle bracket with the vehicle nut you just removed.
VEHICLE BRACKET
CONTROL
UNIT
830632AT
CONTROL UNIT
BRACKET
VEHICLE
NUT
(Reuse.)
925001AT
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
BII 42536 (0908)
11 of 21
44. Route the engine starter harness along the vehicle harness, and loosely install the engine starter harness and the antenna cable to the vehicle harness with four wire ties.
ANTENNA
CABLE
ENGINE
STARTER
HARNESS
VEHICLE
HARNESS
4 WIRE TIES
(Loosely install.)
830635BT
45. While wearing gloves, locate and remove the blue tape from the vehicle 2-pin connector (white) behind the fuse box. Plug the vehicle 2-pin connector
(white) into the engine starter harness 2-pin connector.
NOTICE: The aluminum structure under the dashboard
has sharp edges.
FUSE
BOX
VEHICLE 2-PIN CONNECTOR
(white)
46. Unplug the vehicle 24-pin connector (white) from the bottom of the fuse box, and plug it into the engine starter harness 24-pin connector. Plug the remaining engine starter harness 24-pin connector into the fuse box 24-pin connector (white).
FUSE BOX
FUSE BOX 24-PIN
CONNECTOR
(White)
ENGINE STARTER
HARNESS 24-PIN
CONNECTOR
FUSE BOX
ENGINE
STARTER
HARNESS
24-PIN
CONNECTOR
VEHICLE
24-PIN
CONNECTOR
(White)
862707AT
FUSE BOX 24-PIN
CONNECTOR (White)
47. Attach the clip from the engine starter harness
24-pin connector to the clip holder on the bottom of the fuse box area shown.
FUSE BOX
FUSE BOX
BLUE TAPE
(Remove.)
ENGINE STARTER
HARNESS 2-PIN
CONNECTOR
ATTACHMENT POSITION
ENGINE
STARTER
HARNESS
24-PIN
CONNECTOR
(Connected in
862708AT
862706AT
12 of 21
BII 42536 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
48. Unplug the vehicle 20-pin connector (green) from the fuse box, and plug it into the engine starter harness
20-pin connector. Plug the remaining engine starter harness 20-pin connector into the fuse box 20-pin connector.
FUSE BOX
FUSE BOX 20-PIN
CONNECTOR
FUSE BOX
49. Unplug the vehicle 5-pin connector from the fuse box, and plug it into the engine starter harness 5-pin connector. Plug the remaining engine starter harness 5-pin connector into the fuse box 5-pin connector.
NOTE: Check that the 5-pin connectors are plugged in properly and locked. A loose connector can cause the engine to stall during driving.
Connector unlock
2
Pull.
1
Push.
Connector lock
Push.
2
FUSE BOX 20-PIN
CONNECTOR
VEHICLE
20-PIN
CONNECTOR
(Green)
ENGINE STARTER HARNESS
20-PIN CONNECTORS
862709AT
VEHICLE
5-PIN
CONNECTOR
3
1
FUSE BOX 5-PIN
CONNECTOR
FUSE BOX
ENGINE STARTER
HARNESS 5-PIN
CONNECTORS
Push.
2
Push.
1
Connector lock
FUSE BOX
FUSE BOX 5-PIN
CONNECTOR
925004AT
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
BII 42536 (0908)
13 of 21
50. Plug the engine starter harness 12-pin connector into the fuse box 12-pin connector.
ENGINE STARTER HARNESS
12-PIN CONNECTOR
FUSE BOX 12-PIN
CONNECTOR
FUSE
BOX
53. Remove the vehicle ground bolt. Attach the engine starter harness ground terminal to the vehicle ground terminal, and reinstall the vehicle ground bolt.
ENGINE STARTER HARNESS
GROUND TERMINAL
FUSE BOX
ENGINE STARTER
HARNESS
925005AT
51. Wrap one urethane tape around the engine starter harness 5-pin connector and the vehicle 5-pin connector as shown.
VEHICLE
HARNESS
ENGINE
STARTER
HARNESS
VEHICLE
GROUND
TERMINAL
VEHICLE
GROUND
BOLT
(Reuse.)
ENGINE
STARTER
HARNESS
VEHICLE
HARNESS
830636CT
54. Secure the antenna cable and engine starter harness to the vehicle harness with four wire ties
WIRE
TIE
VEHICLE
5-PIN
CONNECTOR
URETHANE
TAPE
ENGINE STARTER HARNESS
5-PIN CONNECTOR
830642CT
52. Secure the engine starter harness 5-pin connector and the engine starter harness to the vehicle harness with one wire tie.
WIRE
TIE
ANTENNA CABLE
(Bundle up the excess.)
ENGINE
STARTER
HARNESS
VEHICLE
HARNESS
4 WIRE TIES
830644BT
55. Bundle up the excess antenna cable as shown, and secure it to the vehicle harness with one wire tie.
14 of 21
BII 42536 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
56. To gain access to route the engine starter harness, remove the vehicle bolt from the vehicle bracket, and remove the vehicle unit.
60. Route the two 12-pin connectors and two 8-pin connectors of the engine starter harness along the vehicle harness as shown.
ENGINE STARTER
HARNESS 8-PIN
CONNECTOR
VEHICLE
HARNESS
VEHICLE
UNIT
CONTROL
UNIT
VEHICLE
BRACKET
VEHICLE
BOLT
830657AT
57. Attach the engine starter harness clip to the vehicle bracket.
GREEN
TAPE
VEHICLE CLIP
WIRE
TIE
VEHICLE BRACKET
ENGINE
STARTER
HARNESS
CLIP
ENGINE STARTER
HARNESS 12-PIN
CONNECTOR
830646AT
61. Route the two 12-pin connectors and two 8-pin connectors of the engine starter harness along the vehicle harness as shown.
ENGINE
STARTER
HARNESS
12-PIN
CONNECTOR
ENGINE STARTER
HARNESS
8-PIN CONNECTOR
VEHICLE
HARNESS
WIRE
TIE
VEHICLE
CLIP
ENGINE STARTER
HARNESS
830645DT
58. Align the green tape on the engine starter harness with vehicle clip, and secure the engine starter harness to the vehicle harness with two wire ties.
59. Reinstall the vehicle unit.
VEHICLE
HARNESS
830658AT
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
BII 42536 (0908)
15 of 21
62. Unplug the vehicle 12-pin connector from the turn signal switch, and plug it into the engine starter harness 12-pin connector. Plug the remaining engine starter harness 12-pin connector into the turn signal switch.
VEHICLE 12-PIN
CONNECTOR
ENGINE
STARTER
HARNESS
12-PIN
CONNECTOR
64. Secure the engine starter harness to the vehicle harness with four wire ties. Do not secure it to the
SRS harness.
WIRE TIE
ENGINE
STARTER
HARNESS
WIRE TIE
WIRE TIE
TURN SIGNAL
SWITCH
830647AT
63. Unplug the vehicle 8-pin connector from the wiper switch, and plug it into the engine starter harness 8pin connector. Plug the remaining engine starter harness 8-pin connector into the wiper switch.
VEHICLE
HARNESS
WIRE TIE
830649AT
65. Secure the engine starter harness to the vehicle harness with one wire tie.
VEHICLE
HARNESS
ENGINE
STARTER
HARNESS
8-PIN
CONNECTOR
WIRE TIE
ENGINE
STARTER
HARNESS
830650AT
WIPER SWITCH
VEHICLE 8-PIN
CONNECTOR
830648AT
16 of 21
BII 42536 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
66. Secure the engine starter harness to the vehicle harness with two wire ties as shown.
ENGINE STARTER
HARNESS
VEHICLE HARNESS
VEHICLE
CLIP
69. Check that all wire harnesses and cables are routed properly and that all connectors are plugged in.
70. Reinstall all removed parts. Take care not to pinch the side curtain airbag with the clip during reinstallation of the left front A-pillar trim. Do not push the front pillar trim excessively.
71. Reconnect the negative cable to the battery.
72. Check the operation of the headlights and the windshield wipers.
73. Enter the anti-theft codes for the audio system and the navigation system (if equipped).
74. Reset the clock on vehicles without navigation.
2 WIRE
TIES
VEHICLE
CLIP
830651CT
67. Under the hood, locate the area where the caution label will attach. Using isopropyl alcohol on a shop towel, clean the area where the caution label will attach.
HOOD
Clean with isopropyl alcohol.
CAUTION
LABEL
925002AT
68. Attach the caution label to the hood in the area shown.
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
BII 42536 (0908)
17 of 21
75. Do the REMOTE ENGINE STARTER
REGISTRATION (Page 18) and FUNCTION
CHECK (Page 21).
REMOTE ENGINE STARTER REGISTRATION
1.
Acquire a PCM Code from ISIS.
CAR ICON
5.
Select the “Honda Systems”, then click the check button.
792901AH
2.
Connect the HDS tester to the OBD II data link connector, then turn the ignition switch on.
3.
Start the HDS, and click the car icon.
4.
Input the VIN and other required information, then click the check button.
Select the
“Honda Systems.”
CHECK BUTTON
752503AS
6.
Select the “R/C ENG STARTER” and click the check button.
Select the
“R/C ENG STARTER.”
CHECK BUTTON
752504AS
18 of 21
Input the VIN and other requirements.
CHECK BUTTON
752502AS
BII 42536 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
7.
Check that “REMARKS” is shown, then click the check button.
Check that “REMARKS” is shown.
9.
Check that “Obtain PCM-code (IMMOBILIZER PCM
CODE) from iN. This vehicle’s VIN will be required to obtain the password. (USA)” is shown, then click the check button.
Check that “Obtain PCM-code (IMMOBILIZER PCM
CODE) from iN. This vehicle’s VIN will be required to obtain the password. (USA)” is shown.
CHECK BUTTON
752505AS
8.
Select the “REGISTER REMOTE CONTROL
ENGINE STARTER UNIT”, then click the check button.
CHECK BUTTON
752507AS
10. Input the PCM Code, then click the check button.
NOTE: To ensure security, the PCM code
(password) is changed everyday, so it is impossible to register the remote controlled engine starter if the date of the PCM code acquisition and registration are different. The date of the HDS tester should also be the same.
Input the PCM Code.
Select the
“REGISTER REMOTE CONTROL
ENGINE STARTER UNIT.”
CHECK BUTTON
752506AS
CHECK BUTTON
752509AS
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
BII 42536 (0908)
19 of 21
11. Check that “The registration of the Remote Control
Engine Starter Unit has been completed” is shown, then click the check button.
Check that “The registration of the
Remote Control Engine Starter Unit has been completed” is shown.
CHECK BUTTON
752510AS
12. Check that “Check that the engine can be started by the Transmitter” is shown, then click the check button.
Check that “Check that the engine can be started by the Transmitter” is shown.
CHECK BUTTON
752511AS
13. Perform the function test on the next page, then remove the HDS.
20 of 21
BII 42536 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
FUNCTION CHECK
Operating Conditions
• Hood is closed
• Shift lever in Park
• The key is outside the vehicle
• All doors and trunk lid closed and locked
Inspection
1.
Within 1 second, press the command button, and then the start button on the transmitter. The engine should start if all operating conditions are met.
Does the engine start?
Yes - Operation is normal.
No:
• Make sure all “Operating Conditions” are met.
• Check the engine starter harness connections.
• Connect the HDS and check for an indicated failure.
(Refer to the appropriate service manual for details.)
2.
Press the command button on the transmitter, and within
1 second, press the stop button. The engine should stop.
Does the engine stop?
STOP
BUTTON
DISPLAY
COMMAND
BUTTON
START
BUTTON
Yes - Operation is normal.
No - Check the engine starter harness connections.
3.
After the engine has stopped, start the engine again, and then check that the engine stops after each of the following tests:
NOTE: After each test you must open and close the driver’s door.
• Move the shift lever out of the P position.
• Unlock or open the doors or the trunk lid.
• Open the hood.
• Insert the key in the ignition switch.
• Press the brake pedal.
Does the engine stop after each of these tests?
TRANSMITTER
732904AY
Yes - Operation is normal.
No - Check the engine starter harness connections.
4.
Check that the power window or the moonroof does not function and the shift lever does not move to any position but the P position when the engine is started with the transmitter.
5.
Press the command button on the transmitter two times, and check the vehicle condition on the display.
6.
Check the operation of the transmitter when the vehicle is 100 m to 150 m (325 to 490 ft.) away and in direct sight.
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
BII 42536 (0908)
21 of 21

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Remotely start your vehicle
- Start your engine from up to 100 to 150 meters away
- Engine stops automatically if door, hood or trunk lid is opened
- Engine stops automatically if key is inserted in ignition or gear is shifted out of park