Acura 08E91-TK4-200A Remote Engine Starter, 08E92-TL2-200 Remote Control Engine Starter Installation Instructions
Below you will find brief information for Remote Engine Starter 08E91-TK4-200A, Remote Control Engine Starter 08E92-TL2-200. The Remote Engine Starter 08E91-TK4-200A and Remote Control Engine Starter 08E92-TL2-200 are designed to allow you to start your vehicle remotely using a transmitter. This can be helpful in a variety of situations, such as when you are cold in the winter or when you need to warm up your car before you go to work.
Advertisement
Advertisement
INSTALLATION
INSTRUCTIONS
PARTS LIST
Remote Engine Starter Unit Kit
P/N 08E91-TK4-200A
Transmitter
Accessory
REMOTE CONTROL
ENGINE STARTER
Application
2010 TSX
L4
Publications No.
BII 41546
Issue Date
AUG 2009
Remote Control Engine Starter Attachment Kit
P/N 08E92-TL2-200
Engine starter harness
Control unit
Antenna
Key ring
Protective tape (black)
Caution label
Fuse label
Accessory User’s
Information Manual
Quick Start Guide
Control unit bracket
Template
3 Relays
Flange nut
18 Wire ties
7 Urethane tapes
A-Pillar clip
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
BII 41546 (0908)
08E92-TL2-2000-91
1 of 21
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Flat-tip screwdriver
Small flat-tip screwdriver
Ratchet
10 mm Socket
Combination wrench
Diagonal cutters
Isopropyl alcohol
Shop towel
Tape measure
Scale
Scissors
Rubber mallet
HDS (Honda Diagnostic System)
Masking tape
2 Pairs of needle nose pliers
Plastic Trim Tool
T/N SILTRIMTL10
Illustration of the Engine Starter Installed on the
Vehicle
ANTENNA ENGINE STARTER
HARNESS
1.
Make sure you have the anti-theft code for the radio, then write down the radio station presets.
2.
Disconnect the negative cable from the battery.
Setting the Control Unit
3.
Touch the metal part of the screwdriver to any metal part of the vehicle to discharge any static electricity.
CONTROL
UNIT
SMALL
FLAT-TIP
SCREWDRIVER
SWITCHES
SWITCHES
Discharge any static electricity.
SET
SW:1 RR Junction unit ------------------- > OFF
SW:2 Trunk or Tailgate -------------------- > OFF
SW:3 Smart Entry --------------------------- > OFF
SW:4 Horn or Buzzer Answerback ---- > OFF
SW:5 Trunk Main SW----------------------- > OFF
SW:6 Reserve--------------------------------- > OFF
3A FUSE
2 FUSE BLOCKS
40A
792020BH
INSTALLATION
Client Information: The information in this installation
instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by
“do-it-yourselfers.”
NOTE: This antenna should only be installed if the ambient air temperature 15°C (60°F) or above.
2 of 21
BII 41546 (0908)
4.
Check the location of the switches on the control unit.
NOTE:
931602AS
• The switches must be selected before the control unit is plugged in.
• If the switch setting is not correct, the remote engine starter will not operate correctly.
• If you change the switch settings with the unit connected, you must disconnect the unit then reconnect it before the settings change.
5.
Using a small flat-tip screwdriver, adjust the switches on the control unit as shown.
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
6.
Using isopropyl alcohol on a shop towel, clean the area where the protective tape will attach. Attach the protective tape to the control unit over the switches.
8.
Remove the driver’s dashboard under cover (two clips and one pin, and unplug the vehicle connector).
PIN
2 CLIPS
CONTROL
UNIT
PROTECTIVE
TAPE
SWITCHES
ADHESIVE
BACKING
Clean with isopropyl alcohol.
772505AS
7.
Remove the driver’s dashboard lower cover (one screw, twelve clips, and unplug the vehicle connector).
VEHICLE
CONNECTOR
DRIVER’S DASHBOARD
LOWER COVER
VEHICLE
CONNECTOR
DRIVER’S DASHBOARD
UNDER COVER
780802AR
9.
Remove the left front door sill trim (four clips and four retaining tabs).
FRONT
4 RETAINING
TABS
4 CLIPS
LEFT FRONT
DOOR SILL
TRIM
772501AR
SCREW
12 CLIPS
700502AH
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
BII 41546 (0908)
3 of 21
10. Pull away the weatherstrip in the area shown, and remove the left kick panel (two clips).
12. Lower the tilt lever and pull the steering wheel out.
UPPER STEERING
COLUMN COVER
RETAINING
TAB
2 CLIPS
WEATHERSTRIP
(Pull away.)
LEFT KICK
PANEL
772401AR
11. Remove the left dashboard side cover (six clips).
LEFT
DASHBOARD
SIDE COVER
PLASTIC
TRIM
TOOL
Push.
Push.
RETAINING TAB
RETAINING
TAB
LOWER STEERING
COLUMN COVER
810701BH
13. Remove the upper steering column cover:
• Turn the steering wheel clockwise to access the to tab release (point ). Push in on the lower steering column cover in the area shown to release the tab.
• Turn the steering wheel counterclockwise, and release the other side the same way.
• Insert a plastic trim tool between the upper and lower steering column covers to release the retaining tabs (point ).
• Insert a plastic trim tool between the upper cover hood and lower steering column cover to release the two tabs shown.
2 CLIPS
4 CLIPS
780602AR
UPPER COVER
HOOD
4 of 21
BII 41546 (0908)
2 TABS
LOWER STEERING
COLUMN COVER
PLASTIC TRIM TOOL
810702BH
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
14. Remove the upper steering column cover from the upper cover hood (two clips).
UPPER STEERING
COLUMN COVER
16. Remove the roof console:
• Using a plastic trim tool, pry out and remove the left and right lens (four retaining tabs each).
ROOF
CONSOLE
FRONT
CLIP
UPPER COVER
HOOD
702301AH
15. Remove the lower steering column cover (one screw and two self-tapping screws).
LEFT
LENS
4 RETAINING
TABS
RIGHT
LENS
4 RETAINING
TABS
PLASTIC
TRIM TOOL
7N0702AH
• Open the sunglass holder, and remove the four screws.
• Unplug the vehicle connectors to remove the roof console.
VEHICLE
CONNECTORS
FRONT
LOWER STEERING
COLUMN COVER
SELF-TAPPING
SCREW
SCREW
790801BH
ROOF
CONSOLE
SCREW
(Silver)
SUNGLASS
HOLDER
(Open.)
SCREW
(Black)
932302AH
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
BII 41546 (0908)
5 of 21
17. Turn the sunvisor holder 90°, and remove the two sunvisor holders.
SUNVISOR
HOLDER
20. Pull away the weatherstrip from the left front A-pillar trim.
FRONT PILLAR
LEFT FRONT
A-PILLAR TRIM
CLIP
Turn.
PIN
Strike perpendicularly to the vehicle.
CLIP
SHOP
TOWEL
SUNVISOR HOLDER
772302BR
18. Locate the slot in the holder, and insert a flat-tip screwdriver into the slot. Push in and hold the retaining tab.
VANITY MIRROR
LIGHT CONNECTOR
Rotate towards the door.
HOLDER
LEFT
SUNVISOR
(Turn rearward.)
Push upward.
FLAT -TIP
SCREWDRIVER
Push and hold the retaining tab.
FRONT
772301BR
19. While holding the retaining tab, rotate towards the door to remove the left sunvisor. Unplug the vanity mirror light connector.
If the retaining tab did not stay pushed in, return the left sunvisor to its original position and repeat the
STRIKE
POINT
WEATHERSTRIP
TRIANGLE
MARK
RUBBER
MALLET
LEFT FRONT
A-PILLAR TRIM
771801BR
21. Using a rubber mallet and a shop towel, gently tap the left front A-pillar trim at the position shown to release the clip.
22. Remove the left front A-pillar trim (one clip).
LEFT FRONT
A-PILLAR TRIM
CLIP
6 of 21
BII 41546 (0908)
771802BR
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
23. Remove and discard the clip from the left front
A-pillar trim, and install a new A-pillar clip (supplied) on the left front A-pillar trim.
CLIP (Discard.)
NEW A-PILLAR CLIP
26. Install the three relays on the engine starter harness relay blocks.
RELAY
LEFT FRONT
A-PILLAR TRIM
771803AR
Routing the Engine Starter Harness
24. Attach the two 40A fuse labels to the engine starter harness fuse block.
2 FUSE LABELS 40A
RELAY
BLOCK
RELAY
BLOCK
ENGINE STARTER
HARNESS
791719CH
27. Route the 12-pin/8-pin/7-pin/5-pin connectors end of the engine starter harness to the ignition switch.
IGNITION
SWITCH
ENGINE STARTER
HARNESS
FUSE BLOCK
3A FUSE LABEL
RELAY
BLOCK
ENGINE STARTER
HARNESS
25. Attach the 3A fuse label to the engine starter harness relay block.
791718AH
12-PIN/8-PIN/7-PIN/
5-PIN CONNECTORS
VEHICLE
BRACKET
791720AH
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
BII 41546 (0908)
7 of 21
28. Unplug the vehicle 5-pin connector from the ignition switch, and plug the engine starter harness 5-pin connector into the ignition switch.
NOTE: Check that the engine starter harness 5-pin connector is plugged to the vehicle connector and locked securely. A loose connector can cause the engine to stall.
VEHICLE 5-PIN
CONNECTOR
IGNITION
SWITCH
ENGINE STARTER
HARNESS 5-PIN
CONNECTOR
29. Wrap one urethane tape around the vehicle 5-pin connector, and tuck it into the area shown.
URETHANE
TAPE
VEHICLE 5-PIN
CONNECTOR
ENGINE STARTER
HARNESS
2
Pull.
1
Push.
3
Connector unlock
2
Push.
Connector lock
1
791801AH
2
Push.
VEHICLE
BRACKET
VEHICLE 5-PIN
CONNECTOR
Push.
1
Connector lock
791802AH
30. Unplug the vehicle 7-pin connector, and plug it into the engine starter harness 7-pin connector. Plug the remaining engine starter harness 7-pin connector into the vehicle 7-pin connector.
IGNITION SWITCH
VEHICLE 7-PIN
CONNECTOR
8 of 21
2 ENGINE STARTER
HARNESS 7-PIN
CONNECTORS
VEHICLE 7-PIN
CONNECTOR
791803BH
BII 41546 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
31. Unplug the vehicle 12-pin connector, and plug it into the engine starter harness 12-pin connector. Plug the remaining engine starter harness 12-pin connector into the turn signal switch.
VEHICLE 12-PIN
CONNECTOR
2 ENGINE STARTER HARNESS
12-PIN CONNECTORS
33. Secure the engine starter harness to the vehicle harness using two wire ties. Do not secure it to the
SRS harness.
FRONT
VEHICLE
HARNESS
ENGINE
STARTER
HARNESS
TURN SIGNAL
SWITCH
ENGINE STARTER
HARNESS
6D18141Y
32. Unplug the vehicle 8-pin connector, and plug it into the engine starter harness 8-pin connector. Plug the remaining engine starter harness 8-pin connector into the wiper switch.
2 ENGINE STARTER HARNESS
8-PIN CONNECTORS
VEHICLE 8-PIN
CONNECTOR
WIRE TIE
810703AH
34. Secure the engine starter harness to the vehicle harness with three wire ties in the areas shown.
WIRE
TIE
ENGINE STARTER
HARNESS 7-PIN CONNECTOR
VEHICLE
HARNESS
WIRE TIE
ENGINE
STARTER
HARNESS
WIRE
TIE
VEHICLE
HARNESS
Inside.
WIPER
SWITCH
ENGINE STARTER
HARNESS
6D18151Y
ENGINE
STARTER
HARNESS
VEHICLE
CLIP
ENGINE
STARTER
HARNESS
WIRE
TIE
VEHICLE
HARNESS
Inside.
791804BH
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
BII 41546 (0908)
9 of 21
35. Attach the engine starter harness relay block onto the vehicle relay block as shown.
39. Route the engine starter harness through the opening in the vehicle frame, and toward the front of the fuse box as shown.
VEHICLE FRAME
ENGINE
STARTER
HARNESS
RELAY
BLOCK
VEHICLE FRAME
VEHICLE
RELAY
BLOCK
791805BH
36. Align the green tape on the engine starter harness with the holes in the dashboard behind the tilt lever, and secure the engine starter harness to the dashboard with one wire tie.
TILT
LEVER
ENGINE
STARTER
HARNESS
FUSE
BOX
ENGINE
STARTER
HARNESS
ENGINE STARTER
HARNESS CLIP
791902EH
40. Attach the engine starter harness clip to the vehicle frame as shown.
HOLES
VEHICLE
HARNESS
WIRE
TIE
GREEN
TAPE
ENGINE
STARTER
HARNESS
WIRE TIE
GREEN
TAPE
DASHBOARD
VEHICLE
CLIP
ENGINE STARTER
HARNESS
VEHICLE
HARNESS
WIRE TIE
791901BH
37. Align the green tape on the engine starter harness with the vehicle clip shown, and secure the engine starter harness to the vehicle harness with one wire tie.
38. Secure the engine starter harness to the vehicle harness with one wire tie at the location shown.
10 of 21
BII 41546 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
41. Unplug the vehicle 5-pin connector from the fuse box. Plug the engine starter harness 5-pin connector into the fuse box 5-pin connector. Wrap one urethane tape around the vehicle 5-pin connector.
NOTE: Check that the engine starter harness 5-pin connector is plugged to the vehicle connector and locked securely. A loose connector can cause the engine to stall.
Connector lock
Push.
2
URETHANE
TAPE
VEHICLE
5-PIN
CONNECTOR
42. Plug the engine starter harness 12-pin connector into the fuse box 12-pin connector.
FUSE BOX
Push.
1
VEHICLE
5-PIN
CONNECTOR
ENGINE STARTER
HARNESS 5-PIN
CONNECTOR
ENGINE STARTER
HARNESS
Push.
2
FUSE
BOX
FUSE BOX 12-PIN
CONNECTOR
ENGINE STARTER
HARNESS 12-PIN
CONNECTOR
791904DH
43. Remove the vehicle ground bolt. Attach the engine starter harness ground terminal to the vehicle ground terminal, and reinstall the vehicle ground bolt as shown.
VEHICLE
GROUND
TERMINAL
ENGINE STARTER
HARNESS
GROUND TERMINAL
2
Pull.
1
Push.
3
Connector unlock Connector lock
1
791903DH
VEHICLE
GROUND
BOLT
(Reuse.)
7N0703AH
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
BII 41546 (0908)
11 of 21
44. Loosely secure the engine starter harness to the vehicle harness with one wire tie.
46. Attach the engine starter harness 24-pin connector onto the vehicle connector.
ENGINE
STARTER
HARNESS
HOOD
OPENER
ENGINE
STARTER
HARNESS
WIRE TIE
(Loosely secure.)
VEHICLE
HARNESS
791905DH
45. Unplug the vehicle 24-pin connector from the fuse box, and plug it into the engine starter harness
24-pin connector. Plug the remaining engine starter harness 24-pin connector into the fuse box.
FUSE BOX
VEHICLE CONNECTOR
Installing the Antenna
47. Using scissors, cut out the template.
ENGINE
STARTER
HARNESS
24-PIN
CONNECTOR
Plugged together in
792001DH
SCISSORS
ENGINE
STARTER
HARNESS
2 ENGINE STARTER
HARNESS 24-PIN
CONNECTORS
2 VEHICLE
24-PIN
CONNECTORS
791906DH
Cut out.
TEMPLATE
792005BH
12 of 21
BII 41546 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
48. Using two pairs of needle nose pliers, bend the antenna plate according to the full scale drawing shown.
ANTENNA
ANTENNA
PLATE
15 mm
(0.6 in.)
10 mm
(0.4 in.)
2 PAIRS OF
NEEDLE NOSE
PLIERS
49. Get the antenna. Starting near the antenna end of the cable, wrap three urethane tapes around the antenna cable at the measurements shown.
ANTENNA
ANTENNA
CABLE
390 mm
(15 in.)
3 URETHANE
TAPES
30 mm
(1.2 in.)
710 mm
(28 in.)
20 mm
(0.8 in.)
20 mm
(0.8 in.)
ANTENNA CABLE
Cut.
SCALE
792006BH
URETHANE
TAPE
2 URETHANE TAPES (1/2)
700601BH
50. Using scissors, cut one urethane tape in half. Wrap the two halves of the urethane tape around the antenna cable at the measurements shown.
51. Attach the template to the windshield. Align the template with the black ceramic area as shown.
BLACK CERAMIC
CORRECT
TEMPLATE
Align.
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
BII 41546 (0908)
BLACK
CERAMIC
WINDSHIELD
MASKING
TAPE
REARVIEW MIRROR
TEMPLATE
932501AH
13 of 21
52. Using isopropyl alcohol on a shop towel, clean the windshield where the antenna will attach.
HEADLINER
56. Using isopropyl alcohol on a shop towel, clean the roof panel where the urethane tape will attach.
ANTENNA
CABLE
ROOF PANEL
TEMPLATE
ADHESIVE
BACKING
ANTENNA
PLATE
ANTENNA
792008BH
53. Remove the adhesive backing from the antenna.
Insert the antenna plate over the headliner, and attach the antenna to the windshield aligning it with the template.
54. Remove the template.
55. Gently pull down the headliner, and tuck the antenna cable under it. Be careful not to crease the headliner.
Cut.
VEHICLE
HARNESS
2 URETHANE TAPES (1/2)
792010AH
57. Using scissors, cut one urethane tape in half. Secure the antenna cable to the roof panel with the two halves of urethane tape.
58. Pull away the weatherstrip. Route the antenna cable down under the dashboard. Tuck the antenna cable between the left front A-pillar and the dashboard, and reinstall the weatherstrip.
WEATHERSTRIP
HEADLINER
DASHBOARD
ANTENNA
CABLE
VEHICLE
HARNESS
792009AH
LEFT FRONT
A-PILLAR
ANTENNA CABLE
7N0701AH
14 of 21
BII 41546 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
59. Secure the antenna cable to the vehicle harness with four wire ties.
NOTE: If equipped, do not secure the wire ties to the front drain tube if the vehicle is equipped with the moonroof.
61. Secure the antenna cable with the one wire tie
loosely installed to the vehicle harness in step 44.
VEHICLE HARNESS
WIRE TIE
ANTENNA
CABLE
FRONT
DRAIN
TUBE
(If equipped.)
VEHICLE
HARNESS
932303AH
60. Secure the vehicle 5-pin connector unplugged in
step 41 to the vehicle harness with one wire tie.
VEHICLE 5-PIN
CONNECTOR
Unplugged in
VEHICLE
HARNESS
VEHICLE
HARNESS
ANTENNA
CABLE
WIRE TIE
(Loosely installed
WIRE TIE
(Loosely secure.)
792014EH
62. Route the antenna cable along the vehicle harness, and loosely secure the antenna cable to the vehicle harness with three wire ties.
Installing the Control Unit
63. Install the control unit bracket to the control unit.
CONTROL UNIT
BRACKET
WIRE
TIE
ANTENNA
CABLE
CONTROL
UNIT
792013DH
6D18461Y
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
BII 41546 (0908)
15 of 21
64. Plug the engine starter harness 28-pin connector into the control unit.
ENGINE STARTER
HARNESS
67. Secure the control unit to the vehicle frame using the flange nut.
VEHICLE FRAME
CLIP
ENGINE STARTER
HARNESS 28-PIN
CONNECTOR
CONTROL UNIT
BRACKET
CONTROL
UNIT
792015BH
65. Install the clip of the engine starter harness on the control unit bracket.
66. Plug the antenna terminal into the control unit.
ANTENNA
TERMINAL
CONTROL
UNIT
CONTROL
UNIT
FLANGE
NUT
792016BH
68. Attach the engine starter harness relay block clip to the vehicle frame.
VEHICLE
FRAME
6D18480Y
ENGINE STARTER
HARNESS RELAY
BLOCK
CLIP
792017AH
16 of 21
BII 41546 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
69. Bundle up the excess antenna cable, and secure it to the vehicle harness with the three loosely installed wire ties from step 62.
WIRE TIE
(Loosely installed
72. Attach the caution label to the hood in the area shown.
73. Check that all wire harnesses and cables are routed properly and that all connectors are plugged in.
74. Reinstall all removed parts. Check that all clips and other fasteners are installed securely. Take care not to pinch the side curtain airbag with the clip during reinstallation of the left front A-pillar trim. Do not push the front A-pillar trim excessively.
75. Reconnect the negative cable to the battery.
Check that the electrical accessory and other electrical systems function properly.
76. Enter the customer’s radio anti-theft code and reset the radio station presets.
77. Reset the clock on the models without the navigation system.
78. Do the “REMOTE ENGINE STARTER
REGISTRATION” and “FUNCTION CHECK.”
WIRE TIE
Bundle up the antenna cable.
VEHICLE HARNESS
792018EH
70. Secure the antenna cable to the vehicle harness with one additional wire tie.
71. Under the hood, locate the area where the caution label will attach. Using isopropyl alcohol on a shop towel, clean the hood where the caution label will attach.
HOOD
Clean with isopropyl alcohol.
CAUTION
LABEL
ADHESIVE
BACKING
931601AS
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
BII 41546 (0908)
17 of 21
REMOTE ENGINE STARTER REGISTRATION
1.
Acquire a PCM Code from ISIS.
CAR ICON
5.
Select the “Honda Systems”, then click the check button.
792901AH
2.
Connect the HDS tester to the OBD II data link connector, then turn the ignition switch on.
3.
Start the HDS, and click the car icon.
4.
Input the VIN and other requirements in accordance with the HDS, then click the check button.
Select the
“Honda Systems.”
CHECK BUTTON
752503AS
6.
Select the “R/C ENG STARTER” and click the check button.
18 of 21
Input the VIN and other requirements.
CHECK BUTTON
752502AS
Select the
“R/C ENG STARTER.”
CHECK BUTTON
752504AS
BII 41546 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
7.
Check that “REMARKS” is shown, then click the check button.
Check that “REMARKS” is shown.
9.
Check that “Obtain PCM-code (IMMOBILIZER PCM
CODE) from iN. This vehicle’s VIN will be required to obtain the password. (USA)” is shown, then click the check button.
Check that “Obtain PCM-code (IMMOBILIZER PCM
CODE) from iN. This vehicle’s VIN will be required to obtain the password. (USA)” is shown.
CHECK BUTTON
752505AS
8.
Select the “REGISTER REMOTE CONTROL
ENGINE STARTER UNIT”, then click the check button.
CHECK BUTTON
752507AS
10. Input the PCM Code, then click the check button.
NOTE: To ensure security, the PCM code
(password) is changed everyday, so it is impossible to register the remote controlled engine starter if the date of the PCM code acquisition and registration are different. The date of the HDS tester should also be the same.
Input the PCM Code.
Select the
“REGISTER REMOTE CONTROL
ENGINE STARTER UNIT.”
CHECK BUTTON
752506AS
CHECK BUTTON
752509AS
© 2009 American Honda Motor Co., Inc. – All Rights Reserved.
BII 41546 (0908)
19 of 21
11. Check that “The registration of the Remote Control
Engine Starter Unit has been completed” is shown, then click the check button.
Check that “The registration of the
Remote Control Engine Starter Unit has been completed” is shown.
CHECK BUTTON
752510AS
12. Check that “Check that the engine can be started by the Transmitter” is shown, then click the check button.
Check that “Check that the engine can be started by the Transmitter” is shown.
20 of 21
CHECK BUTTON
752511AS
BII 41546 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
13. Perform the function test on the next page, then remove the HDS.
FUNCTION CHECK
Operating Conditions
• Hood is closed
• Shift lever in park
• The key is out of the ignition switch
• All doors and trunk lid closed and locked
Inspection
1.
Within 1 second, press the command button, and then the start button on the transmitter.
The engine should start if all operating conditions are met.
Does the engine start?
DISPLAY
Yes - Operation is normal.
No:
• Make sure all “Operating Conditions” are met.
• Check the engine starter harness connections.
• Connect the HDS and check for an indicated failure.
(Refer to the appropriate service manual for details.)
STOP
BUTTON
2.
Press the command button on the transmitter, and within 1 second, press the stop button. The engine should stop.
Does the engine stop?
TRANSMITTER
Yes - Operation is normal.
No - Check the engine starter harness connections.
COMMAND
BUTTON
START
BUTTON
3.
After the engine has stopped, start the engine again, and check that the engine stops after each of the following conditions:
NOTE:
• After each test the ignition switch must be cycled, or the driver’s door must be opened and closed.
• Move the shift lever out of the P position.
• Unlock or open the doors or the trunk lid.
• Open the hood.
• Insert the key in the ignition switch.
• Press the brake pedal.
Does the engine stop after each of these tests?
732904AY
Yes - Operation is normal.
No - Check the engine starter harness connections.
4.
Check that the power window or the moonroof does not function and the shift lever does not move to any position but the P position when the engine is started with the transmitter.
5.
Press the command button on the transmitter two times, and check the vehicle condition on the display.
6.
Check the operation of the transmitter when the vehicle is 100 m to 150 m (325 to 490 ft.) away and in direct sight.
21 of 21
BII 41546 (0908) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Remote engine start
- Start vehicle remotely
- Warm up vehicle
- Remote control
- Transmitter included
- Detailed installation guide