INSTALLATION
INSTRUCTIONS
PARTS LIST
Remote Engine Starter Unit Kit
P/N 08E91-TK4-200A
Transmitter
Accessory
REMOTE CONTROL
ENGINE STARTER
Application
2011 TSX L4
Accessory User’s Information Manual
Publications No.
BII 44991
Issue Date
NOV 2010
Quick Start Guide
Control unit
Remote Control Engine Starter Attachment Kit
P/N 08E92-TL2-200A
Engine starter harness
Antenna
Control unit bracket
Template
Key ring
Protective tape (black)
Caution label
3 Relays
Fuse label
Flange nut
18 Wire ties
© 2010 American Honda Motor Co., Inc. – All Rights Reserved.
BII 44991 (1011)
08E92-TL2-2A00-90
1 of 23
7 Urethane tapes
A-Pillar clip
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Flat-tip screwdriver
Small flat-tip screwdriver
Ratchet
10 mm Socket
10 mm Open end wrench
Diagonal cutters
Isopropyl alcohol
Shop towel
Tape measure
Scale
Scissors
Rubber mallet
HDS
Masking tape
Needle nose pliers
Trim Tool Set (T/N SOJATP2014)
Dryer
Illustration of the Remote Control Engine Starter
Installed in the Vehicle
ENGINE STARTER
HARNESS ANTENNA
3A FUSE
2 FUSE BLOCKS
40A
792020BH
INSTALLATION
Client Information: The information in this installation
instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by
“do-it-yourselfers.”
NOTE: This antenna should be installed only if the ambient air temperature 15°C (60°F) or above.
1.
Make sure you have the anti-theft code for the radio, then write down the radio station presets.
2.
Disconnect the negative cable from the battery.
2 of 23
BII 44991 (1011) © 2010 American Honda Motor Co., Inc. – All Rights Reserved.
Setting the Control Unit
If the vehicle is a sedan, go to step 3.
If the vehicle is a sport wagon, go to step 6.
Sedan
3.
Touch the metal part of the screwdriver to any metal part of the vehicle to discharge any static electricity.
CONTROL
UNIT
5.
Using a small flat-tip screwdriver, adjust the switches on the control unit as shown. Go to step 9.
Sport Wagon
6.
Touch the metal part of the screwdriver to any metal part of the vehicle to discharge any static electricity.
CONTROL
UNIT
SMALL
FLAT-TIP
SCREWDRIVER
Discharge any static electricity.
SMALL
FLAT-TIP
SCREWDRIVER
Discharge any static electricity.
SWITCHES
SWITCHES
SWITCHES
SWITCHES
SET
SET
SW:1 RR Junction unit ------------------- > OFF
SW:2 Trunk or Tailgate -------------------- > OFF
SW:3 Smart Entry --------------------------- > OFF
SW:4 Horn or Buzzer Answerback ---- > ON
SW:5 Trunk Main SW ---------------------- > ON
SW:6 Reserve -------------------------------- > OFF
SW:1 RR Junction unit ------------------- > OFF
SW:2 Trunk or Tailgate -------------------- > ON
SW:3 Smart Entry --------------------------- > OFF
SW:4 Horn or Buzzer Answerback ---- > ON
SW:5 Trunk Main SW----------------------- > OFF
SW:6 Reserve--------------------------------- > OFF
071201BX
4.
Check the settings of the switches on the control unit.
NOTE:
• The switches must be set before the control unit is plugged in.
• If the switch settings are not correct, the remote control engine starter will not operate correctly.
• If you are setting the switches with the control unit installed in the vehicle, touch the metal part of the screwdriver to any metal part of the vehicle to discharge any static electricity.
• If you change the switch settings with the unit connected, you must disconnect the unit, then reconnect it before the new settings are recognized.
© 2010 American Honda Motor Co., Inc. – All Rights Reserved.
071202BX
7.
Check the settings of the switches on the control unit.
NOTE:
• The switches must be set before the control unit is plugged in.
• If the switch settings are not correct, the remote control engine starter will not operate correctly.
• If you are setting the switches with the control unit installed in the vehicle, touch the metal part of the screwdriver to any metal part of the vehicle to discharge any static electricity.
• If you change the switch settings with the unit connected, you must disconnect the unit, then reconnect it before the new settings are recognized.
8.
Using a small flat-tip screwdriver, adjust the switches on the control unit as shown.
BII 44991 (1011)
3 of 23
9.
Using isopropyl alcohol on a shop towel, clean the area where the protective tape will attach. Attach the protective tape to the control unit over the switches.
11.
Remove the driver’s dashboard under cover (two clips and one pin, and unplug the vehicle connector).
PIN
CLIP
CONTROL
UNIT
PROTECTIVE
TAPE
SWITCHES
ADHESIVE
BACKING
Remove.
Clean with isopropyl alcohol.
772505AS
10. Remove the driver’s dashboard lower cover (one screw, twelve clips, and unplug the vehicle connector).
VEHICLE
CONNECTOR
DRIVER’S DASHBOARD
LOWER COVER
VEHICLE
CONNECTOR
DRIVER’S DASHBOARD
UNDER COVER
780802AR
12. Remove the left front door sill trim (four clips and four retaining tabs).
FRONT
4 RETAINING
TABS
4 CLIPS
SCREW
12 CLIPS
700502AH
LEFT FRONT
DOOR SILL
TRIM
772501AR
4 of 23
BII 44991 (1011) © 2010 American Honda Motor Co., Inc. – All Rights Reserved.
13. Pull back the door opening seal, and remove the left kick panel (two clips).
15. Lower the tilt lever and pull the steering wheel out.
UPPER STEERING
COLUMN COVER
RETAINING
TAB
2 CLIPS
TRIM
TOOL
Push.
DOOR OPENING
SEAL
Pull back.
DASHBOARD
LEFT SIDE
COVER
LEFT KICK
PANEL
772401AR
14. Remove the dashboard left side cover (six clips).
Push.
2 RETAINING
TABS
RETAINING TAB
LOWER STEERING
COLUMN COVER
810701BH
16. Remove the upper steering column cover:
• Turn the steering wheel clockwise to access the tab (point ). Push in on the lower steering column cover in the areas shown to release the tab. Turn the steering wheel counterclockwise to release the tab on the other side.
• Insert a trim tool between the upper and lower steering column covers to release the retaining tabs (point ) as shown.
• Insert a trim tool between the upper cover hood and lower steering column cover to release two hood hooks as shown.
UPPER
COVER
HOOD
2 CLIPS
4 CLIPS
780602AR
© 2010 American Honda Motor Co., Inc. – All Rights Reserved.
BII 44991 (1011)
2 HOOD
HOOKS
LOWER STEERING
COLUMN COVER
TRIM TOOL
810702BH
5 of 23
• Remove the upper steering column cover from the upper cover hood (two clips).
UPPER STEERING
COLUMN COVER
18. Remove the roof console:
• Using a flat-tip screwdriver with a shop towel, pry out and remove the left and right lenses (four retaining tabs each).
ROOF
CONSOLE
CLIPS
UPPER
COVER
HOOD
702301AH
17. Remove the lower steering column cover (one screw and two self-tapping screws).
4 RETAINING
TABS
SHOP
TOWEL
RIGHT
LENS
LEFT
LENS
4 RETAINING
TABS
FLAT-TIP
SCREWDRIVER
7302010B
• Open the sunglass holder, and remove four screws.
• Unplug the vehicle connectors to remove the roof console.
VEHICLE
CONNECTORS
LOWER STEERING
COLUMN COVER
SELF-TAPPING
SCREW
SCREW
790801BH
SUNGLASS
HOLDER
Open.
SCREW
Black
SCREW
Silver
ROOF
CONSOLE
730202AB
6 of 23
BII 44991 (1011) © 2010 American Honda Motor Co., Inc. – All Rights Reserved.
19. Remove each sunvisor holder by turning it 90°.
SUNVISOR
HOLDER
Turn.
22. Pull the door opening seal away from the left A-pillar trim.
FRONT PILLAR
LEFT
A-PILLAR
TRIM
CLIP
PIN
Strike perpendicularly to the vehicle.
CLIP
SHOP TOWEL
RUBBER
MALLET
SUNVISOR HOLDER
772302BR
20. Locate the slot in the holder, and insert a flat-tip screwdriver into the slot. Push in and hold the retaining tab.
VANITY MIRROR
LIGHT CONNECTOR
Rotate towards the door.
STRIKE
POINT
DOOR
OPENING
SEAL
Pull away.
TRIANGLE
MARK
LEFT
A-PILLAR
TRIM
771801BR
23. Using a rubber mallet and a shop towel, gently tap the left A-pillar trim at the position shown to release the clip.
24. Remove the left A-pillar trim (one clip).
HOLDER
LEFT
SUNVISOR
Pivot down.
Push upward.
FLAT-TIP
SCREWDRIVER
Push and hold the retaining tab.
FRONT
772301BR
21. While holding the retaining tab, rotate the sunvisor towards the door to remove it. Unplug the vanity mirror light connector. If the retaining tab did not stay pushed in, return the left sunvisor to its original position and repeat steps 20 and 21.
LEFT
A-PILLAR TRIM
CLIP
© 2010 American Honda Motor Co., Inc. – All Rights Reserved.
BII 44991 (1011)
771802BR
7 of 23
25. Remove and discard the clip from the left A-pillar trim, and install a new A-pillar clip (supplied) on the left A-pillar trim.
CLIP
Discard.
NEW A-PILLAR CLIP
28. Install three relays in the engine starter harness relay blocks.
RELAYS
RELAY
BLOCK
RELAY
BLOCK
LEFT
A-PILLAR
TRIM
ENGINE STARTER
HARNESS
791719CH
771803AR
Routing the Engine Starter Harness
26. Using isopropyl alcohol on a shop towel, thoroughly clean the areas where the fuse labels will attach.
Attach two 40A fuse labels to the engine starter harness fuse block.
40A FUSE LABELS
FUSE BLOCK
29. Route the 12-pin/8-pin/7-pin/5-pin connector end of the engine starter harness to the ignition switch.
IGNITION
SWITCH
ENGINE
STARTER
HARNESS
3A FUSE LABEL
RELAY
BLOCK
ENGINE STARTER
HARNESS
791718AH
27. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the fuse label will attach.
Attach one 3A fuse label to the engine starter harness relay block.
12-PIN/8-PIN/7-PIN/
5-PIN CONNECTOR
END
VEHICLE
BRACKET
791720AH
8 of 23
BII 44991 (1011) © 2010 American Honda Motor Co., Inc. – All Rights Reserved.
30. Unplug the vehicle 5-pin connector from the ignition switch, and plug the engine starter harness 5-pin connector into the ignition switch.
NOTE: Make sure the engine starter harness 5-pin connector is connected securely to the ignition switch. A loose connection can cause the engine to stall during driving.
VEHICLE 5-PIN
CONNECTOR
IGNITION
SWITCH
ENGINE STARTER
HARNESS 5-PIN
CONNECTOR
ENGINE
STARTER
HARNESS
31. Wrap one urethane tape around the vehicle 5-pin connector, and tuck it into the area shown.
URETHANE
TAPE
VEHICLE 5-PIN
CONNECTOR
2
Push.
VEHICLE
BRACKET
VEHICLE 5-PIN
CONNECTOR
2
Pull.
1
Push.
3
Connector unlock
2
Push.
Push.
1
Connector lock
Connector lock
1
791801AH
791802AH
32. Unplug the vehicle 7-pin connector, and plug it into the engine starter harness 7-pin connector. Plug the remaining engine starter harness 7-pin connector into the vehicle 7-pin connector.
IGNITION SWITCH
VEHICLE 7-PIN
CONNECTOR
© 2010 American Honda Motor Co., Inc. – All Rights Reserved.
BII 44991 (1011)
ENGINE STARTER
HARNESS 7-PIN
CONNECTORS
VEHICLE 7-PIN
CONNECTOR
791803BH
9 of 23
33. Unplug the vehicle 12-pin connector, and plug it into the engine starter harness 12-pin connector. Plug the remaining engine starter harness 12-pin connector into the turn signal switch.
VEHICLE 12-PIN
CONNECTOR
ENGINE STARTER HARNESS
12-PIN CONNECTORS
35. Secure the engine starter harness to the vehicle harness with two wire ties. Do not secure it to the
SRS harness.
FRONT
VEHICLE
HARNESS
ENGINE
STARTER
HARNESS
TURN SIGNAL
SWITCH
ENGINE STARTER
HARNESS
WIRE TIES
810703AH
6D18141Y
34. Unplug the vehicle 8-pin connector, and plug it into the engine starter harness 8-pin connector. Plug the remaining engine starter harness 8-pin connector into the wiper switch.
ENGINE STARTER HARNESS
8-PIN CONNECTORS
VEHICLE 8-PIN
CONNECTOR
36. Secure the engine starter harness to the vehicle harness with three wire ties in the areas shown.
ENGINE STARTER
HARNESS 7-PIN CONNECTOR
Connected in step 32.
WIRE
TIE
VEHICLE
HARNESS
WIRE TIE
WIRE
TIES
ENGINE
STARTER
HARNESS
VEHICLE
HARNESS
Inside.
10 of 23
WIPER
SWITCH
ENGINE STARTER
HARNESS
6D18151Y
BII 44991 (1011)
ENGINE
STARTER
HARNESS
VEHICLE
CLIPS
ENGINE
STARTER
HARNESS
WIRE
TIE
VEHICLE
HARNESS
Inside.
931605AS
© 2010 American Honda Motor Co., Inc. – All Rights Reserved.
37. Attach the engine starter harness relay block onto the vehicle relay block as shown.
41. Route the engine starter harness through the opening in the vehicle frame in front of the fuse box.
VEHICLE FRAME
ENGINE
STARTER
HARNESS
RELAY
BLOCK
VEHICLE
FRAME
VEHICLE
RELAY
BLOCK
FUSE
BOX
ENGINE
STARTER
HARNESS
791805BH
BRAKE PEDAL
38. Align the white tape on the engine starter harness with the holes in the dashboard behind the tilt lever as shown, and secure the engine starter harness to the dashboard with one wire tie.
TILT
LEVER
ENGINE
STARTER
HARNESS
ENGINE STARTER
HARNESS CLIP
931603AS
42. Attach the engine starter harness clip to the hole in the vehicle frame as shown.
HOLES
VEHICLE
HARNESS
WHITE
TAPE
WIRE
TIES
ENGINE
STARTER
HARNESS
WIRE TIE
WHITE
TAPE
DASHBOARD
VEHICLE
CLIP
ENGINE STARTER
HARNESS
VEHICLE
HARNESS
WIRE TIE
791901BH
39. Align the white tape on the engine starter harness with the vehicle clip as shown, and secure the engine starter harness to the vehicle harness with one wire tie.
40. Secure the engine starter harness to the vehicle harness with one wire tie at the location shown.
© 2010 American Honda Motor Co., Inc. – All Rights Reserved.
BII 44991 (1011)
11 of 23
43. Unplug the vehicle 5-pin connector from the fuse box. Plug the engine starter harness 5-pin connector into the fuse box 5-pin connector. Wrap one urethane tape around the vehicle 5-pin connector.
NOTE: Make sure the engine starter harness 5-pin connector is securely connected to the fuse box
5-pin connector. A loose connection can cause the engine to stall during driving.
Connector lock
Push.
2
URETHANE
TAPE
VEHICLE
5-PIN
CONNECTOR
44. Secure the vehicle 5-pin connector unplugged in step 43 to the vehicle harness with one wire tie.
VEHICLE 5-PIN
CONNECTOR
Unplugged and wrapped in
step 43.
VEHICLE
HARNESS
WIRE TIE
Push.
1
FUSE BOX
VEHICLE
5-PIN
CONNECTOR
ENGINE STARTER
HARNESS 5-PIN
CONNECTOR
ENGINE STARTER
HARNESS
Push.
2
FUSE
BOX
931607AS
45. Plug the engine starter harness 12-pin connector into the fuse box 12-pin connector.
FUSE BOX
12-PIN
CONNECTOR
2
Pull.
1
Push.
3
Connector unlock
1
Connector lock
931604AS
FUSE BOX
ENGINE STARTER
HARNESS 12-PIN
CONNECTOR
FUSE BOX 12-PIN
CONNECTOR
931608AS
12 of 23
BII 44991 (1011) © 2010 American Honda Motor Co., Inc. – All Rights Reserved.
46. Remove the vehicle ground bolt. Attach the engine starter harness ground terminal to the vehicle ground terminal, and reinstall the vehicle ground bolt as shown.
VEHICLE
GROUND
TERMINAL
ENGINE STARTER
HARNESS
GROUND TERMINAL
48. Unplug the vehicle 24-pin connector from the fuse box, and plug the engine starter harness 24-pin connector into the fuse box. Plug the remaining engine starter harness 24-pin connector into the vehicle 24-pin connector.
FUSE BOX
VEHICLE
GROUND
BOLT
Reuse.
7N0703AH
47. Loosely install one wire tie around the engine starter harness and the vehicle harness.
ENGINE
STARTER
HARNESS
ENGINE STARTER
HARNESS 24-PIN
CONNECTORS
VEHICLE
24-PIN
CONNECTOR
791906DH
ENGINE
STARTER
HARNESS
VEHICLE
HARNESS
WIRE TIE
Install loosely.
791905DH
© 2010 American Honda Motor Co., Inc. – All Rights Reserved.
BII 44991 (1011)
13 of 23
If the vehicle is equipped with a power tailgate, go to step
49; if not, go to step 52.
With power tailgate
49. Detach the vehicle 2-pin connector from the vehicle
8-pin connector.
Without power tailgate
52. Attach the engine starter harness 24-pin connector onto the existing vehicle 8-pin connector already attached to the side panel.
ENGINE
STARTER
HARNESS
ENGINE
STARTER
HARNESS
HOOD
OPENER
HOOD
OPENER
VEHICLE 2-PIN
CONNECTOR
VEHICLE 2-PIN
CONNECTOR
VEHICLE 8-PIN CONNECTOR
VEHICLE 8-PIN
CONNECTOR
ENGINE STARTER
HARNESS 24-PIN
CONNECTOR
Connected in step 48.
042002AX
50. Attach the engine starter harness 24-pin connector onto the vehicle 8-pin connector.
51. Attach the vehicle 2-pin connector onto the engine starter harness 24-pin connector. Go to step 53.
Installing the Antenna
53. Use scissors to cut out the template.
SCISSORS
ENGINE
STARTER
HARNESS
24-PIN
CONNECTOR
Connected in step 48.
792001DH
Cut out.
TEMPLATE
792005BH
14 of 23
BII 44991 (1011) © 2010 American Honda Motor Co., Inc. – All Rights Reserved.
54. Using two pairs of needle nose pliers, bend the antenna plate according to the full scale drawing below.
ANTENNA
ANTENNA
PLATE
15 mm
(0.6 in.)
10 mm
(0.4 in.)
2 PAIRS OF
NEEDLE NOSE
PLIERS
55. Starting at the antenna end of the cable, wrap three urethane tapes around the antenna cable at the measurements shown.
ANTENNA
ANTENNA
CABLE
390 mm
(15 in.)
3 URETHANE
TAPES
30 mm
(1.2 in.)
710 mm
(28 in.)
20 mm
(0.8 in.)
20 mm
(0.8 in.)
ANTENNA CABLE
Cut in half.
SCALE
792006BH
URETHANE
TAPE
2 URETHANE TAPES (1/2)
700601BH
56. Cut one urethane tape in half. Wrap the two cut pieces of urethane tape around the antenna cable at the measurements shown.
57. Attach the template to the windshield. Align it with the black ceramic as shown.
BLACK CERAMIC
CORRECT
TEMPLATE
Align.
BLACK
CERAMIC
WINDSHIELD
MASKING
TAPE
REARVIEW MIRROR
TEMPLATE
932501AH
© 2010 American Honda Motor Co., Inc. – All Rights Reserved.
BII 44991 (1011)
15 of 23
58. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the antenna will attach.
HEADLINER
62. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the urethane tape will attach.
ANTENNA
CABLE
ROOF PANEL
TEMPLATE
ADHESIVE
BACKING
Remove.
ANTENNA
ANTENNA
PLATE
792008BH
59. Remove the adhesive backing from the antenna.
Insert the antenna plate behind the headliner, align the antenna with the template, and attach the antenna to the windshield.
60. Remove the template.
61. Gently pull down the headliner, and tuck the antenna cable behind it. Be careful not to crease the headliner.
VEHICLE
HARNESS
Cut in half.
URETHANE TAPE
792010AH
63. Use scissors to cut one urethane tape in half. Secure the antenna cable to the roof panel with the two cut pieces of urethane tape.
64. Pull back the door opening seal. Route the antenna cable down under the dashboard. Tuck the antenna cable between the left front A-pillar and the dashboard, and reinstall the door opening seal.
DOOR OPENING
SEAL
Pull back.
HEADLINER
VEHICLE
HARNESS
ANTENNA
CABLE
792009AH
LEFT
A-PILLAR
DASHBOARD
ANTENNA CABLE
7N0701AH
16 of 23
BII 44991 (1011) © 2010 American Honda Motor Co., Inc. – All Rights Reserved.
65. Secure the antenna cable to the vehicle harness with four wire ties. If the vehicle is equipped with a moonroof, do not secure the wire ties to the front drain tube.
Installing the Control Unit
68. Install the control unit bracket to the control unit.
CONTROL UNIT
BRACKET
WIRE TIES
ANTENNA
CABLE
FRONT
DRAIN
TUBE
Do not secure.
VEHICLE
HARNESS
CONTROL
UNIT
6D18461Y
932303AH
66. Secure the antenna cable with the one wire tie loosely installed to the vehicle harness in step 47.
VEHICLE HARNESS
69. Plug the engine starter harness 28-pin connector into the control unit.
ENGINE STARTER
HARNESS
CLIP
ENGINE STARTER
HARNESS 28-PIN
CONNECTOR
VEHICLE
HARNESS
ANTENNA
CABLE
WIRE TIE
Loosely installed in step 47.
WIRE TIES
Install loosely.
792014EH
67. Route the antenna cable along the vehicle harness, and loosely install three wire ties around the antenna cable and the vehicle harness.
CONTROL UNIT
BRACKET
CONTROL
UNIT
792015BH
70. Install the clip on the engine starter harness to the control unit bracket.
© 2010 American Honda Motor Co., Inc. – All Rights Reserved.
BII 44991 (1011)
17 of 23
71. Plug the antenna terminal into the control unit as shown.
ANTENNA
TERMINAL
CONTROL
UNIT
73. Secure the engine starter harness relay block clip to the vehicle frame.
VEHICLE
FRAME
ENGINE STARTER
HARNESS RELAY
BLOCK
CLIP
792017AH
6D18480Y
72. Insert the stud on the control unit bracket through the hole in the vehicle frame, and secure the control unit bracket to the vehicle frame with one flange nut.
74. Bundle the excess antenna cable. Insert the bundled cable under two wire ties loosely installed in step 67.
Secure the antenna cable with the remaining loosely-installed wire tie.
WIRE TIES
Loosely installed in step 67.
VEHICLE FRAME
FLANGE
NUT
STUD
CONTROL
UNIT
BRACKET
CONTROL
UNIT
931606AS
WIRE TIE
Bundle the antenna cable.
VEHICLE HARNESS
792018EH
75. Secure the antenna cable to the vehicle harness with one additional wire tie.
18 of 23
BII 44991 (1011) © 2010 American Honda Motor Co., Inc. – All Rights Reserved.
76. Open the hood, and locate the area where the caution label will attach. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the caution label will attach.
HOOD
Clean with isopropyl alcohol.
CAUTION
LABEL
ADHESIVE
BACKING
Remove.
931601AS
77. Attach the caution label to the hood as shown.
78. Check that all wire harnesses and cables are routed properly and that all connectors are plugged in.
79. Reinstall all removed parts. Check that all clips and other fasteners are installed securely. Take care not to pinch the side curtain airbag with the clip during reinstallation of the left A-pillar trim. Do not push excessively on the A-pillar trim.
80. Reconnect the negative cable to the battery.
Check that all electrical accessories and other electrical systems function properly.
81. Enter the client’s radio anti-theft code and reset the radio station presets.
82. Reset the clock on models without a navigation system.
83. Do the “REMOTE ENGINE STARTER
REGISTRATION” and “FUNCTION CHECK.”
© 2010 American Honda Motor Co., Inc. – All Rights Reserved.
BII 44991 (1011)
19 of 23
REMOTE ENGINE STARTER REGISTRATION
1.
Acquire the PCM Code from the Interactive Network.
2.
Connect the HDS tester to the OBD II data link connector, then turn the ignition switch to the on (II) position.
3.
Start the HDS, and click the car icon.
5.
Select Honda Systems, then click the check button.
CAR ICON
792901AH
4.
Input the VIN and other required information into the
HDS, then click the check button.
Select
“Honda Systems.”
CHECK BUTTON
752503AS
6.
Select R/C ENG STARTER and click the check button.
Select
“R/C ENG STARTER.”
CHECK BUTTON
752504AS
20 of 23
Input the VIN and other required information.
CHECK BUTTON
752502AS
BII 44991 (1011) © 2010 American Honda Motor Co., Inc. – All Rights Reserved.
7.
A REMARKS message will display. Click on the check button.
“REMARKS” message.
9.
The following message will display: Obtain PCM
code (IMMOBILIZER PCM CODE) from iN. This vehicle’s VIN will be required to obtain the
password (USA). Click on the check button.
“Obtain PCM-code” message.
CHECK BUTTON
752505AS
8.
Select REGISTER REMOTE CONTROL ENGINE
STARTER UNIT, then click the check button.
CHECK BUTTON
752507AS
10. Input the PCM Code, then click the check button.
NOTE: To ensure security, the PCM code
(password) is changed every day, so it is impossible to register the remote control engine starter if the dates of the PCM code acquisition and registration are different. The date on the HDS tester should also be the same.
Input the PCM Code.
Select
“REGISTER REMOTE
CONTROL ENGINE
STARTER UNIT.”
CHECK BUTTON
752506AS
CHECK BUTTON
752509AS
© 2010 American Honda Motor Co., Inc. – All Rights Reserved.
BII 44991 (1011)
21 of 23
11.
The following message will display: The
registration of the Remote Control Engine Starter
Unit has been completed. Click on the check
button.
“The registration of the Remote
Control Engine Starter Unit has been completed.”
CHECK BUTTON
752510AS
12. The following message will display: Check that the
engine can be started by the Transmitter. Click on
the check button.
“Check that the engine can be started by the Transmitter.”
CHECK BUTTON
752511AS
13. Perform the Function Check on page 23, then disconnect the HDS.
22 of 23
BII 44991 (1011) © 2010 American Honda Motor Co., Inc. – All Rights Reserved.
FUNCTION CHECK
Operating Conditions
• Hood is closed
• Shift lever in park
• The key is out of the ignition switch
• All doors and trunk lid or tailgate closed and locked
Inspection
1.
Press the command button, and then, within one second, press the start button on the transmitter.
The engine should start if all operating conditions are met.
Does the engine start?
Yes - Operation is normal.
No:
• Make sure all “Operating Conditions” are met.
• Check the engine starter harness connections.
• Connect the HDS and check for an indicated failure.
(Refer to the appropriate service manual for details.)
2.
Press the command button on the transmitter and, within
1 second, press the stop button. The engine should stop.
Does the engine stop?
STOP
BUTTON
DISPLAY
COMMAND
BUTTON
START
BUTTON
Yes - Operation is normal.
No - Check the engine starter harness connections.
TRANSMITTER
3.
After the engine has stopped, start the engine again, and check that the engine stops after each of the following conditions:
NOTE: After each test the ignition switch must be cycled, or the driver’s door must be opened and closed.
• Move the shift lever out of the P position.
• Unlock or open the doors or the trunk lid or tailgate.
• Open the hood.
• Insert the key in the ignition switch.
• Press the brake pedal.
Does the engine stop after each of these tests?
732904AY
Yes - Operation is normal.
No - Check the engine starter harness connections.
4.
Check that the power windows and the moonroof do not function, and that the shift lever does not move to any position but the P position when the engine is started with the transmitter.
5.
Start the engine again, press the command button on the transmitter two times, and check the vehicle condition on the display.
6.
Check the operation of the transmitter when the vehicle is 100 m to 150 m (325 to 490 ft.) away and in direct sight.
© 2010 American Honda Motor Co., Inc. – All Rights Reserved.
BII 44991 (1011)
23 of 23
