Craftmade BW248AG6 Installation guide

READ THESE INSTRUCTIONS AND
SAVE THEM FOR FUTURE USE
Installation Guide
For Models:
BW248AG6
BW248SS6
E192641
net weight of fan: 27.58 lb (12.51 kg)
Table of Contents:
Safety Tips. pg. 1
Unpacking Your Fan. pg. 2
Parts Inventory. pg. 2
Installation Preparation. pg. 3
Hanging Bracket Installation. pg. 3
Fan Assembly. pgs. 4 - 5
Wiring. pg. 6
Canopy Assembly. pg. 7
Light Kit Assembly (Optional). pgs. 7 - 8
Alternate Final Assembly, Without Light Kit. pg. 8
Automated Learning Process./
Activating Code. pg. 9
Wall Control Operation. pg. 9
Remote Control Operation. pg. 10
Testing Your Fan. pg. 10
Troubleshooting. pg. 11
Warranty. pg. 11
Parts Replacement. pg. 11
PRINTED IN CHINA
SAFETY TIPS.
WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit
panel before you begin the fan installation or before servicing the fan or installing accessories.
1.
READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN
AND SAVE THESE INSTRUCTIONS.
CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges.
2.
Make sure all electrical connections comply with Local Codes or Ordinances, the National Electrical Code,
and ANSI/NFPA 70-1999. If you are unfamiliar with electrical wiring or if the house/building wires are
different colors than those referred to in the instructions, please use a qualified electrician.
3.
Make sure you have a location selected for your fan that allows clear space for the blades to rotate, and at
least ten (10) feet (3.05 meters) of clearance between the floor and the fan blade tips. The fan should be
mounted so that the tips of the blades are at least thirty (30) inches (76 centimeters) from walls or other
upright structures.
4.
The outlet box and ceiling support joist used must be securely mounted, and capable of supporting at least
35 pounds (16 kilograms). The outlet box must be supported directly by the building structure. Use only
CUL (Canada) or UL (USA) listed outlet boxes marked "FOR FAN SUPPORT."
WARNING: To reduce the risk of fire, electrical shock, or personal injury, mount to the outlet box marked
"Acceptable for Fan Support of 15.9 kg (35 lbs.) or less," and use the mounting screws provided with the outlet box.
Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support and may
need to be replaced. Consult a qualified electrician if in doubt.
WARNING: To reduce the risk of fire, electrical shock, or personal injury, wire connectors provided with this fan are
designed to accept only one12 gauge house wire and two lead wires from the fan. If your house wire is larger than
12 gauge or there is more than one house wire to connect to the corresponding fan lead wires, consult an
electrician for the proper size wire connectors to use.
WARNING: If using this fan in a DAMP location, this fan must be connected to a supply circuit that is protected by
a Ground Fault Circuit Interrupter (GFCI) to reduce the risk of personal injury, electrical shock or death.
5.
6.
7.
Electrical diagrams are for reference only. Light kits that are not packed with the fan must be CUL (Canada)
or UL (USA) listed and marked suitable for use with the model fan you are installing. Switches must be
CUL (Canada) or UL (USA) general use switches. Refer to the instructions packaged with the light kits and
switches for proper assembly.
After installation is complete, check that all connections are absolutely secure.
After making electrical connections, spliced conductors should be turned upward and pushed carefully up
into the outlet box. The wires should be spread apart with the grounded conductor and the
equipment-grounding conductor on opposite sides of the outlet box.
WARNING: To reduce the risk of electrical shock or fire, do not use this fan with any solid state speed control
device or control fan speed with a full range dimmer switch. [Using a full range dimmer switch to control fan
speed will cause a loud humming noise from fan.]
8.
Do not insert anything between the fan blades while they are rotating.
WARNING: To reduce the risk of personal injury, do not bend the blade arms during assembly or after installation.
Do not insert objects into the path of the blades.
WARNING: To avoid personal injury or damage to the fan and other items, be cautious when working around or
cleaning the fan.
9.
Do not use water or detergents when cleaning the fan or fan blades. A dry dust cloth or lightly dampened
cloth will be suitable for most cleaning.
WARNING: To reduce the risk of personal injury, use only parts provided with this fan. The use of parts OTHER
than those provided with this fan will void the warranty.
NOTE: The important safety precautions and instructions appearing in the manual are not meant to cover all
possible conditions and situations that may occur. It must be understood that common sense and caution are
necessary factors in the installation and operation of this fan.
page 1
1. Unpacking Your Fan.
Carefully open the packaging. Remove items
from Styrofoam inserts. Remove motor assembly
and place on carpet or Styrofoam to avoid
damage to finish. Do not discard fan carton or
Styrofoam inserts should this fan need to be
returned for repairs.
Check against parts inventory that all parts have
been included.
2. Parts Inventory.
a
c
b
a. canopy. 1 piece
b. hanging bracket. 1 piece
c. 4½in. downrod and hanging ball. 1 piece
d. remote control receiver. 1 piece
d
f
e
g
e. wall control and plate. 2 separate pieces
f. remote control transmitter and plate.
2 separate pieces
j
i
h
g. canopy cover (in hardware pack). 1 piece
h. small fitter plate (for use without light kit).
1 piece
i. large fitter plate (for use with light kit).
1 piece
k
m
l
j. yoke cover. 1 piece
k. safety cable (already attached to motor).
1 piece
n
o
p
l. glass shade. 1 piece
m. light kit fitter. 1 piece
q
n. metal cover. 1 piece
o. finial plate (pre-attached to light kit fitter).
1 piece
p. finial (pre-attached to light kit fitter). 1 piece
r
w/wall
control
w/ remote
q. motor assembly. 1 piece
r. hardware packs
IMPORTANT REMINDER: You must
use the parts provided with this fan for
proper installation and safety.
bulbs required:
2 x 13 watt compact fluorescent bulbs,
(included)
page 2
To prevent personal injury and damage, ensure
that the hanging location allows the blades a
clearance of 10 feet (3.05m) from the floor and
30in. (76 cm) from any wall or obstruction.
This fan is suitable for room sizes up to
400 square feet (37.2 square meters).
12ft. - 20ft.
(3.66m - 6.1m)
3. Installation Preparation.
blade edge
30
10 feet inches
(3.05m) (76cm)
12ft. - 20ft.
(3.66m - 6.1m)
downrod
installation
This fan can be mounted with a downrod on a
regular (no-slope) ceiling only. Fan CANNOT
mount as a flushmount installation nor on a
vaulted ceiling.
flushmount
installation
CANNOT be
installed on
angled or
vaulted ceilings
Installation requires these tools:
Phillips screwdriver, flathead screwdriver,
adjustable pliers or wrench, stepladder, wire
cutters, and rated electrical tape
4. Hanging Bracket Installation.
Turn off circuit breakers to current fixture from
breaker panel and be sure operating light switch is
turned to the OFF position.
WARNING: Failure to disconnect power supply prior
to installation may result in serious injury.
ON
ON
OFF
OFF
Remove existing fixture.
WARNING: When using an existing outlet box, be
sure the outlet box is securely attached to the building
structure and can support the full weight of the fan.
Ensure outlet box is clearly marked "Suitable for Fan
Support." If not, it must be replaced with an approved
outlet box. Failure to do so can result in serious injury.
CAUTION: Be sure outlet box is grounded properly
and that a ground wire (GREEN or bare) is present.
Install hanging bracket to outlet box using original
screws, spring washers and flat washers provided
with new or original outlet box.* Arrange electrical
wiring around the back of the hanging bracket and
away from the hanging bracket opening.
*Note: It is very important that you use the proper
hardware when installing the hanging bracket as this
will support the fan.
page 3
hanging bracket
flat washers
spring washers
outlet box screws
5. Fan Assembly.
If you wish to extend the hanging length of
your fan, you must remove the hanging ball
from the 4½in. downrod provided to use with
an extended downrod (sold separately). [If you
wish to use the 4½in. downrod, please proceed to
instructions following the dotted line below.]
set screw hole
set screw
stop pin
hanging ball
To remove hanging ball, loosen set screw on
hanging ball, lower hanging ball and remove
stop pin. Slide hanging ball off the original
downrod, A, and slide it down the longer
downrod, B (the top of the downrod should be
noted as having a set screw hole; use this hole
when setting the set screw). Insert stop pin into
top of extended downrod and raise hanging
ball. Be sure stop pin aligns with slots on the
inside of the hanging ball. Tighten set screw
securely.
A
B
Tip: To prepare for threading electrical wires
through downrod, apply a small piece of
electrical tape to the ends of the electrical
wires--this will keep the wires together when
threading them through the downrod.
electrical wiring
Locate canopy cover in hardware pack. Loosen
yoke set screws and nuts in yoke at top of
motor assembly. Remove pin and clip from
motor assembly yoke. Slide downrod through
canopy, canopy cover* and yoke cover.
*NOTE: Canopy cover must be turned with
shiny side toward the motor assembly.
safety cable
downrod
canopy
canopy cover
yoke cover
Thread safety cable and electrical wires through
downrod and pull extra wire slack from the
upper end of the downrod.
yoke set screw
and nut
Thread downrod into the motor assembly yoke
until holes for pin and clip in downrod align
with holes in yoke--make sure wires do not get
twisted. Re-insert pin and clip. Securely tighten
yoke set screws and nuts. Lower yoke cover to
motor assembly.
clip
pin
motor
assembly
["Fan Assembly" continued on next page.]
NOTE: The important safety precautions and
instructions appearing in the manual are not meant
to cover all possible conditions and situations that
may occur. It must be understood that common
sense and caution are necessary factors in the
installation and operation of this fan.
page 4
5. Fan Assembly. (cont.)
With the hanging bracket secured to the outlet
box and able to support the fan, you are now
ready to hang your fan. Grab the fan firmly with
two hands. Slide downrod through opening in
hanging bracket and let hanging ball rest on
the hanging bracket. Turn the hanging ball slot
until it lines up with the hanging bracket tab.
wood
ceiling
joist
safety cable loop
wood screw
and washer
safety cable
WARNING: Failure to align slot in hanging ball
with tab in hanging bracket may result in
serious injury or death
canopy
CAUTION: Due to the size (width) of this fan, it is
advisable to seek the help of another person to
hold the stepladder in place and to then help
lift the fan up to you once you are set on the
ladder.
Find a secure attachment point (wood ceiling
joist highly recommended) and secure safety
cable. It will be necessary to use a heavy duty
wood screw, washer and lock washer (not
supplied) with the safety cable loop. If
necessary, adjust the loop at the end of the
safety cable. The loop at the end of the safety
cable should just fit over the threads on the
wood screw. Extra cable slack can be left in
ceiling area.
page 5
motor
assembly
Las modificaciones no aprobadas por la parte responsable de la conformidad
podrían invalidar la autorización del usuario para manejar el equipo.
6. Wiring.
*NOTA: Se han hecho pruebas en este equipo y se ha comprobado que cumple con los límites para un
aparato digital de clase B, de acuerdo con la Parte 15 de las Reglas de la FCC. Se concibieron estos
límites para proveer protección razonable contra la interferencia adversa en una instalación residencial.
Este equipo produce, usa y puede radiar energía de radiofrecuencia y, si no se instala y no se usa según
las instrucciones, puede causar interferencia adversa en la radiocomunicación. Sin embargo, no hay
ninguna garantía de que no habrá interferencia en una instalación en particular. Si este equipo sí causa
interferencia adversa en la recepción de radio o televisión, que se puede determinar apagando y
prendiendo el equipo, se le urge al usuario a intentar rectificar la interferencia tomando una o más de
las medidas que siguen:
* Orientar la antena de nuevo o localizarla en otro sitio.
* Aumentar la separación entre el equipo y el receptor.
* Conectar el equipo a un tomacorriente en un circuito distinto al cual está
conectado el receptor.
CAUTION: Be sure outlet box is properly grounded
and that a ground wire (GREEN or Bare) is present.
Make sure all electrical connections comply with Local
Codes or Ordinances and the National Electrical Code
(or Canadian Electrical Code). If you are unfamiliar
with electrical wiring or if the house/building wires are
different colors than those referred to in the diagram
to the right, please use a qualified electrician.
Solicitar ayuda del distribuidor o un técnico de radio/televisión.
ground (green
or bare)
white supply wire
WARNING: If using this fan in a DAMP location, this
fan must be connected to a supply circuit that is
protected by a Ground Fault Circuit Interrupter
(GFCI) to reduce the risk of personal injury, electrical
shock or death.
black supply wire
ground (green
or bare)
blue
white
black
black
white
grey
When downrod is secured in place on the hanging
bracket, wire the RECEIVER with wire connectors
provided as shown in diagram at right.
Tip: While you are wiring, keep in mind that wires
must not obstruct receiver from sliding into
hanging bracket.
from ceiling
from fan
from receiver
* Wrap each wire connector separately with
electrical tape as an extra safety measure.
black
AC IN L
from receiver
black
Gently insert receiver (flat side up) into hanging
bracket and carefully push wires and taped wire
connectors into outlet box. Let antenna rest outside
of hanging bracket.
white
AC IN N
white
grey
blue
IN ORDER TO WIRE WALL CONTROL, remove existing
wall switch. Wire the WALL CONTROL with wire
connectors provided as shown in diagram at right.
* Wrap each wire connector separately with electrical
tape as an extra safety measure. Gently push wires
and taped wire connectors into outlet box.
receiver
antenna
(wiring for receiver)
outlet box
wall
control
green/
bare
ground
Attach wall control to outlet box and secure with
screws from original wall switch. Attach front plate to
wall control using 2 screws provided in the wall
control.
black (TO POWER supply)
(wiring for wall control)
page 6
code
switches
black (OUT to fan)
black
(AC IN from
breaker box)
plate
D
green
black
1 2 3 4 X
Use a ballpoint pen or a small screwdriver to set the
code switches 1 through 4 on the wall control. Factory
setting is pre-set and not recommended for use. Write
down number sequence for use in Section 10.
NOTE: Because this fan requires compact fluorescent
bulbs, the dimmer switch (labeled D and X) has been
pre-set to the "OFF" position (X). [Most compact
fluorescent bulbs, including the ones provided with
this fan, are not compatible for use with dimmer
controls.]
dimmer
switch
antenna
7. Canopy Assembly.
hanging bracket
Locate 2 screws on underside of hanging bracket and
remove screw closest to the open end of the hanging
bracket. Partially loosen the other screw. Lift canopy to
hanging bracket. Place rounded part of slotted hole in
canopy over loosened screw in hanging bracket and
push up. Twist canopy to lock. Re-insert screw that was
removed and then tighten both screws securely. Slide
canopy cover up to canopy, aligning rounded part of
slotted holes in canopy cover with screwheads in
bottom of canopy. Turn canopy cover to the right
(clockwise) until it stops.
screw
canopy
screw
*Remember that antenna for remote control receiver
must rest outside of hanging bracket.
canopy cover
8. Light Kit Assembly (Optional).
motor
assembly
If you wish to USE the light kit, remove 1 screw from
motor plate on underside of motor assembly and
partially loosen the other 2 screws. Align slotted holes
in large fitter plate with loosened screws in motor
plate, allowing molex connections from motor
assembly to come through hole in middle of large fitter
plate. Twist large fitter plate to lock. Re-insert screw
that was previously removed and securely tighten all 3
screws with Phillips screwdriver.
motor plate
Remove 1 screw from post on underside of large fitter
plate and partially loosen the other 2 screws.
large fitter plate
Connect WHITE wire from motor assembly to WHITE
wire from light kit fitter. Connect BLACK (or BLUE) wire
from motor assembly to BLACK wire from light kit
fitter. Be sure molex connections snap together
securely.
molex connections
motor
assembly
Align slotted holes in light kit fitter with loosened
screws in large fitter plate. Twist light kit fitter to lock.
Re-insert screw that was previously removed. Tighten
all 3 screws securely.
Install two 13 watt compact fluorescent medium base
bulbs (included).
IMPORTANT: When you need to replace bulbs,
please allow bulbs and glass shade to cool down
before touching.
Hg
large
fitter plate
molex connections
LAMP CONTAINS MERCURY
light kit fitter
Manage in accordance with Spills, Disposal and Site Cleanup
Requirements. In case of breakage, follow clean-up
procedures provided by contacts below.
bulb
www.epa.gov/cflcleanup
1-866-284-4010
["Light Kit Assembly" continued on next page.]
page 7
8. Light Kit Assembly (Optional). (cont.)
Remove finial and finial plate from threaded
rod at bottom of light kit fitter. Raise glass
shade in order to align threaded rod on light kit
fitter with hole in middle of glass shade and
push up gently, allowing threaded rod to come
through hole. Replace finial plate and finial that
were previously removed. Secure glass shade to
light kit fitter by tightening finial. Do NOT
overtighten finial as glass may crack or break.
motor
assembly
light kit
fitter
glass shade
threaded rod
finial
finial plate
9. Alternate Final Assembly, Without Light Kit.
If you do NOT wish to use the light kit, remove
1 screw from motor plate on underside of
motor assembly and partially loosen the other
2 screws. Align slotted holes in small fitter
plate with loosened screws in motor plate,
allowing molex connections from motor
assembly to come through hole in middle of
small fitter plate. Twist small fitter plate to lock.
Re-insert screw that was previously removed
and securely tighten all 3 screws with Phillips
screwdriver.
motor
assembly
motor plate
small fitter plate
Remove 3 screws from outer edge of small
fitter plate.
molex connections
Align holes in metal cover with holes in small
fitter plate. Secure metal cover with 3 screws
that were just removed.
motor
assembly
small fitter
plate
metal cover
page 8
10. Automated Learning Process./
Activating Code.
transmitter
(back)
CAUTION: The remote control transmitter can be
programmed to multiple receivers or fans. If this is
not desired, turn wall switch off to any other
programmable receiver or fan.
code
switches
Remove battery cover on back side of remote
control transmitter.
Use a ballpoint pen or a small screwdriver to set
the code switches 1 through 4 for the transmitter.
Use the same number sequence used when
wiring the wall control in Section 6 (page 6).
dimmer
switch
Note: Because this fan requires compact
fluorescent bulbs, the dimmer switch (labeled D
and X) has been pre-set to the "OFF" position (X).
[Most compact fluorescent bulbs, including the
ones provided with this fan, are not compatible for
use with dimmer controls.]
12V battery
battery
cover
Install one 12-volt battery (included) in
transmitter. Re-attach battery cover on transmitter.
IMPORTANT: Store the transmitter away from
excess heat or humidity. To prevent damage to
transmitter, remove the battery if not used for
long periods.
Restore electrical power and then set slider switch
on wall control to the ON position. Within 30
seconds of turning on the wall control, press the
fan "OFF" button ( ), located on the front of the
transmitter, for 5 seconds or until light blinks
twice. Test the light and fan functions to confirm
the learning process is complete--see Section 13.
11. Wall Control Operation.
ON/OFF slider switch - turns wall control ON or OFF
HI button - turns the 2 smaller fans to HIGH speed
MED button - turns the 2 smaller fans to MEDIUM speed
LOW button - turns the 2 smaller fans to LOW speed
FAN OFF button - turns the 2 smaller fans OFF
button - turns main fan ON/OFF when pressed once
(i.e., controls ROTATION of the ENTIRE fan)
page 9
transmitter
(front)
12. Remote Control Operation.
HI button - turns the 2 smaller fans to HIGH speed
MED button - turns the 2 smaller fansto MEDIUM speed
LOW button - turns the 2 smaller fans to LOW speed
button - turns the 2 smaller fans OFF
button - turns light ON/OFF when tapped quickly.
Pressing and holding button down for more
than 0.7 seconds converts it into a dimmer.
button - turns main fan ON/OFF when pressed once
(i.e., controls ROTATION of the ENTIRE fan)
13. Testing Your Fan.
It is recommended that you test fan before
finalizing installation. Locate ON/OFF slider switch
on wall control and set to the ON position. Test
ROTATION/OFF function of main fan with button
used to control rotation of fan; test fan speeds of
smaller fans with different fan speed buttons and
OFF button. Test light with light button. Next,
locate remote control. Test fan speeds (and OFF)
with the different fan speed buttons and then test
rotation of fan (and OFF) as was done with wall
control. Test light with button. If the remote
control operates all of the functions of the fan,
battery has been installed correctly. If the wall
and/or remote controls do (does) not operate all of
the fan/light functions, refer to "Troubleshooting"
section to solve any issues before contacting
Customer Service.
The tilt angle of the smaller fans may be adjusted
up or down by simply moving them gently up or
down.
WARNING: To avoid personal injury or damage to
the fan, both the main fan and the smaller fans
MUST BE TURNED OFF before adjusting the tilt
angle of the smaller fans up or down.
NOTE: If remote control interferes with other
appliances, change code switches on remote
control transmitter and wall control to another
code. If you do change the code, turn power off first
and then remove battery cover. After setting new
code on transmitter (AND wall control), go back to
instructions in last paragraph of Section 10 (page 9).
page 10
main fan
light
smaller fan
smaller fan
Troubleshooting.
Warranty.
WARNING: Failure to disconnect power supply prior
to troubleshooting any wiring issues may result in
serious injury.
CRAFTMADE/ELLINGTON LIFETIME WARRANTY:
CRAFTMADE/ELLINGTON warrants this fan to the original
household purchaser for use in damp locations (which is
defined as indoors, enclosed porches or enclosed patios)
under the following provisions:
1-YEAR WARRANTY: CRAFTMADE/ELLINGTON will replace
or repair any fan which has faulty performance due to a
defect in material or workmanship. Contact
Craftmade/Ellington Customer Service at 1-800-486-4892
to arrange for return of fan. Return fan, shipping prepaid, to
Craftmade/Ellington. We will repair or ship you a
replacement fan, and we will pay the return shipping cost.
5-YEAR WARRANTY: CRAFTMADE/ELLINGTON will repair or
replace at no charge to the original purchaser any fan
motor that fails to operate satisfactorily when failure
results from normal use.
RETURN FAN MOTOR ONLY, shipping prepaid, to
Craftmade/Ellington. We will repair or ship purchaser a
replacement motor and Craftmade/Ellington will pay the
return shipping cost.
6-YEAR to LIFETIME LIMITED WARRANTY:
CRAFTMADE/ELLINGTON will repair the fan, at no charge
for labor only to the original purchaser, if the fan motor
fails to operate satisfactorily when failure results from
normal use. Parts used in the repair will be billed to the
purchaser at prevailing prices at time of repair.
The purchaser shall be responsible for all costs incurred
in the removal, reinstallation and shipping of the product
for repairs.
This warranty does not apply when damage from
outdoor use and/or mechanical, physical, electrical or
water abuse results in causing the malfunction.
Deterioration of finishes or other parts due to time or
exposure to salt air is specifically exempted under this
warranty.
Neither Craftmade/Ellington nor the manufacturer will
assume any liability resulting from improper installation or
use of this product. In no case shall the company be liable
for any consequential damages for breach of this, or any
other warranty expressed or implied whatsoever. This
limitation as to consequential damages shall not apply in
states where prohibited.
Problem: Fan fails to operate.
Solutions:
1. Check power to wall switch/wall control.
2. Check to be sure code switches in remote control
transmitter and wall control are set properly.
3. Verify that receiver is wired properly.
4. Verify that wall control is wired properly.
5. Check to be sure fan is wired properly.
6. Check that red light on remote control transmitter turns
on when a button is pressed indicating that the battery is
good.
7. Learning process between fan, remote control
transmitter and wall control may not have been successful
and code was not activated. Turn off power and repeat
instructions in the last paragraph of Section 10 (page 9).
Problem: Light kit (optional) not lighting.
Solutions:
1. Check wall switch to fan.
2. Check that bulbs are installed correctly.
3. Check that wires in canopy are wired properly.
4. Check to be sure code switches are set properly in
remote control transmitter and wall control.
5. Verify that molex connections in light kit fitter are
connected properly.
6. Learning process between fan, remote control
transmitter and wall control may not have been successful
and code was not activated. Turn off power and repeat
instructions in the last paragraph of Section 10 (page 9).
Problem: Fan operates but light fails (if applicable).
Solutions:
1. Check that bulbs are installed correctly.
2. Check to be sure wires in canopy are wired properly.
3. Verify that molex connections in light kit fitter are
connected properly.
4. Replace defective bulbs with same type of bulb.
Problem: Fan and light fail to operate with remote control.
Solutions:
1. Check battery power to remote control.
2. Check to be sure code switches are set properly in
remote control transmitter and wall control.
3. Learning process between fan, remote control
transmitter and wall control may not have been successful
and code was not activated. Turn off power and repeat
instructions in the last paragraph of Section 10 (page 9).
Problem: Fan wobbles.
Solutions:
1. Check to be sure set screw(s) on motor assembly yoke is
(are) tightened securely.
2. Check to be sure set screw on hanging ball is tightened
securely.
page 11
Parts Replacement.
For parts and information, please refer to
"Parts Inventory" on page 2.
Craftmade/Ellington Customer Support:
1-800-486-4892
www.craftmade.com