Cisco 7304 Installation guide

Cisco 7304 Router Modular Services Card
and Shared Port Adapter Hardware
Installation Guide
March 2005
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 526-4100
Text Part Number: OL-4681-01
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL
STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT
SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE
OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required
to correct the interference at their own expense.
The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not
installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to
comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable
protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.
Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital
devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television
communications at your own expense.
You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its
peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:
• Turn the television or radio antenna until the interference stops.
• Move the equipment to one side or the other of the television or radio.
• Move the equipment farther away from the television or radio.
• Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits
controlled by different circuit breakers or fuses.)
Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public
domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH
ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT
LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF
DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,
WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO
OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
CCSP, CCVP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn,
and iQuick Study are service marks of Cisco Systems, Inc.; and Access Registrar, Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the
Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Empowering the Internet
Generation, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, FormShare, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, IP/TV, iQ Expertise,
the iQ logo, iQ Net Readiness Scorecard, LightStream, Linksys, MeetingPlace, MGX, the Networkers logo, Networking Academy, Network Registrar, Packet, PIX,
Post-Routing, Pre-Routing, ProConnect, RateMUX, ScriptShare, SlideCast, SMARTnet, StrataView Plus, TeleRouter, The Fastest Way to Increase Your Internet Quotient,
and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.
All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship
between Cisco and any other company. (0502R)
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
Copyright © 2004-2005, Cisco Systems, Inc.
All rights reserved.
CONTENTS
Objectives
vii
Organization
vii
Related Documentation
viii
Obtaining Documentation viii
Cisco.com ix
Documentation DVD ix
Ordering Documentation ix
Documentation Feedback
ix
Cisco Product Security Overview x
Reporting Security Problems in Cisco Products
Obtaining Technical Assistance xi
Cisco Technical Support Website xi
Submitting a Service Request xi
Definitions of Service Request Severity
x
xii
Obtaining Additional Publications and Information
xii
Introduction to MSCs and SPAs 1-1
Modular Service Cards 1-1
Shared Port Adapters 1-2
MSC and SPA Compatibility
Modular Optics Compatibility
1-2
1-3
Carrier Card and SPA Compatibility
2-1
Carrier Card Summary 2-1
Checking Hardware and Software Compatibility
SPA Blank Filler Plates 2-2
2-2
MSC-100 Overview 2-2
Board Components 2-2
LEDs 2-4
Physical Specifications 2-5
Carrier Card Slot Locations on the Cisco 7304 Router
SPA Slot Numbering on the MSC-100 2-5
SPA Interface Addresses on MSCs 2-6
SPA Summary 3-1
Checking Hardware and Software Compatibility
2-5
3-2
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
iii
Contents
Bandwidth Oversubscription
3-2
FastEthernet SPA Overview 3-2
LEDs 3-2
Cables, Connectors, and Pinouts
GigabitEthernet SPA Overview 3-5
LEDs 3-5
Cables, Connectors, and Pinouts
RJ-45 Connectors 3-6
SFP Connections 3-7
3-3
3-5
SFP-FCGE-S Modules 3-8
SFP-FCGE-L Modules 3-8
SFP-GE-Z Modules 3-8
SFP Module Cabling and Connection Equipment
CWDM SFPs 3-10
3-9
OC-3 POS SPA Overview 3-10
2-Port and 4-Port OC-3c/STM-1 POS SPA LEDs 3-11
2-Port and 4-Port OC-3c/STM-1 POS SPA Interface Specifications 3-11
2-Port and 4-Port OC-3c/STM-1 POS SPA Optical Transceiver Modules and Cables
OC-12 POS SPA Overview 3-13
1-Port OC-12c/STM-4 POS SPA LEDs 3-14
1-Port OC-12c/STM-4 POS SPA Interface Specifications 3-14
1-Port OC-12c/STM-4 POS SPA SFP Optical Transceiver Modules and Cables
3-12
3-15
T3/E3 Serial SPA Overview 3-16
2-Port and 4-Port T3/E3 Serial SPA LEDs 3-16
2-Port and 4-Port T3/E3 Serial SPA Interface Specifications 3-17
2-Port and 4-Port T3/E3 Serial SPA Cables and Connectors 3-17
Required Tools and Equipment
4-1
Safety Guidelines 4-1
Safety Warnings 4-1
Statement 1001—Work During Lightning Activity 4-2
Statement 1008—Class 1 Laser Product 4-3
Statement 1030—Equipment Installation 4-4
Statement 1031—EU Public Network Port 4-6
Statement 1041—Disconnecting Telephone-Network Cables
Statement 1043—Installation Hazard 4-8
Statement 1056—Unterminated Fiber Cable 4-10
Statement 1071—Warning Definition 4-12
Electrical Equipment Guidelines 4-14
Telephone Wiring Guidelines 4-15
4-7
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
iv
OL-4681-01
Contents
Preventing Electrostatic Discharge Damage
Laser/LED Safety
4-15
4-16
4-19
Handling MSCs
5-1
Online Insertion and Removal
5-2
MSC Installation and Removal
Handling SPAs
5-3
6-1
Online Insertion and Removal
6-2
SPA Installation and Removal
6-2
Optical Device Installation and Removal (SPA-2GE-7304 optional procedure)
Installing and Removing Small Form-Factor Pluggable Modules 6-4
Cleaning Optical Devices 6-4
6-4
Checking the Installation 6-4
Verifying the Installation 6-4
Using show Commands to Verify MSC and SPA Status 6-6
Using show Commands to Display SPA Information 6-7
Using the ping Command to Verify Network Connectivity 6-8
SPA Cable Management Brackets
Troubleshooting
7-1
Error Messages
7-4
Other Troubleshooting Resources
Packing a SPA for Shipment
6-9
7-4
7-4
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
v
Contents
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
vi
OL-4681-01
Preface
This preface describes the objectives and organization of this document and explains how to find
additional information on related products and services. This preface contains the following sections:
•
Objectives, page vii
•
Organization, page vii
•
Related Documentation, page viii
•
Obtaining Documentation, page viii
•
Documentation Feedback, page ix
•
Cisco Product Security Overview, page x
•
Obtaining Technical Assistance, page xi
•
Obtaining Additional Publications and Information, page xii
Objectives
This document describes the modular services cards (MSCs) and shared port adapters (SPAs) that are
supported on the Cisco 7304 router. This document also describes how to install the supported MSCs
and SPAs and how to troubleshoot the installation.
Organization
This document contains the following chapters:
Section
Title
Description
Chapter 1
MSCs and SPA Product Overview
Provides an introduction to carrier cards, SPAs,
and supported optical modules.
Chapter 2
Overview: Cisco 7304 Router Carrier Provides an MSC/SPA compatibility summary.
Cards
For each supported MSC, provides a summary of
MSC characteristics and an MSC overview.
Chapter 3
Overview: Cisco 7304 Router Shared For each supported SPA, provides a summary of
Port Adapters
SPA characteristics and a SPA overview.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
vii
Preface
Related Documentation
Section
Title
Description
Chapter 4
Preparing to Install a Modular
Services Card or a Shared Port
Adapter
Describes the required tools, equipment, and
safety guidelines for installing MSCs and SPAs.
Chapter 5
Installing and Removing a Carrier
Card
Describes the procedures for installing and
removing an MSC on the Cisco 7304 router.
Chapter 6
Installing and Removing a Shared
Port Adapter
Describes the procedures for installing and
removing a SPA and verifying the installation on
the Cisco 7304 router.
Chapter 7
Troubleshooting the Installation
Provides information for troubleshooting the
installation of MSCs and SPAs.
Related Documentation
The documentation listed below is available online and on the Documentation DVD.
Your router, switch, or gateway and the Cisco IOS software running on it contain extensive features,
which are documented in the following resources:
•
Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide
•
Cisco IOS software:
– For Cisco IOS configuration information and support, refer to the configuration guide or
command reference for a Cisco IOS mainline release. You can also refer to the specific Cisco
IOS software document for a particular feature.
– To see if a feature is supported by a Cisco IOS release, to locate the software document for that
feature, or to check the minimum software requirements of Cisco IOS software with the
hardware installed on your router, Cisco maintains the Software Advisor tool on Cisco.com.
You must be a registered user on Cisco.com to access this tool. The tool can be accessed at
http://www.cisco.com/cgi-bin/Support/CompNav/Index.pl.
Note
•
You can access Cisco IOS software configuration and hardware installation and maintenance
documentation on the World Wide Web at http://www.cisco.com. Translated documentation is
available at the following URL: http://www.cisco.com/public/countries_languages.shtml.
For international agency compliance, safety, and statutory information for WAN interfaces:
– Regulatory Compliance and Safety Information for the Cisco 7304 Internet Router
Obtaining Documentation
Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several
ways to obtain technical assistance and other technical resources. These sections explain how to obtain
technical information from Cisco Systems.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
viii
OL-4681-01
Preface
Documentation Feedback
Cisco.com
You can access the most current Cisco documentation at this URL:
http://www.cisco.com/univercd/home/home.htm
You can access the Cisco website at this URL:
http://www.cisco.com
You can access international Cisco websites at this URL:
http://www.cisco.com/public/countries_languages.shtml
Documentation DVD
Cisco documentation and additional literature are available in a Documentation DVD package, which
may have shipped with your product. The Documentation DVD is updated regularly and may be more
current than printed documentation. The Documentation DVD package is available as a single unit.
Registered Cisco.com users (Cisco direct customers) can order a Cisco Documentation DVD (product
number DOC-DOCDVD=) from the Ordering tool or Cisco Marketplace.
Cisco Ordering tool:
http://www.cisco.com/en/US/partner/ordering/
Cisco Marketplace:
http://www.cisco.com/go/marketplace/
Ordering Documentation
You can find instructions for ordering documentation at this URL:
http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm
You can order Cisco documentation in these ways:
•
Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from
the Ordering tool:
http://www.cisco.com/en/US/partner/ordering/
•
Nonregistered Cisco.com users can order documentation through a local account representative by
calling Cisco Systems Corporate Headquarters (California, USA) at 408 526-7208 or, elsewhere in
North America, by calling 1 800 553-NETS (6387).
Documentation Feedback
You can send comments about technical documentation to bug-doc@cisco.com.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
ix
Preface
Cisco Product Security Overview
You can submit comments by using the response card (if present) behind the front cover of your
document or by writing to the following address:
Cisco Systems
Attn: Customer Document Ordering
170 West Tasman Drive
San Jose, CA 95134-9883
We appreciate your comments.
Cisco Product Security Overview
Cisco provides a free online Security Vulnerability Policy portal at this URL:
http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html
From this site, you can perform these tasks:
•
Report security vulnerabilities in Cisco products.
•
Obtain assistance with security incidents that involve Cisco products.
•
Register to receive security information from Cisco.
A current list of security advisories and notices for Cisco products is available at this URL:
http://www.cisco.com/go/psirt
If you prefer to see advisories and notices as they are updated in real time, you can access a Product
Security Incident Response Team Really Simple Syndication (PSIRT RSS) feed from this URL:
http://www.cisco.com/en/US/products/products_psirt_rss_feed.html
Reporting Security Problems in Cisco Products
Cisco is committed to delivering secure products. We test our products internally before we release them,
and we strive to correct all vulnerabilities quickly. If you think that you might have identified a
vulnerability in a Cisco product, contact PSIRT:
Tip
•
Emergencies — security-alert@cisco.com
•
Nonemergencies — psirt@cisco.com
We encourage you to use Pretty Good Privacy (PGP) or a compatible product to encrypt any sensitive
information that you send to Cisco. PSIRT can work from encrypted information that is compatible with
PGP versions 2.x through 8.x.
Never use a revoked or an expired encryption key. The correct public key to use in your correspondence
with PSIRT is the one that has the most recent creation date in this public key server list:
http://pgp.mit.edu:11371/pks/lookup?search=psirt%40cisco.com&op=index&exact=on
In an emergency, you can also reach PSIRT by telephone:
•
1 877 228-7302
•
1 408 525-6532
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
x
OL-4681-01
Preface
Obtaining Technical Assistance
Obtaining Technical Assistance
For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, Cisco
Technical Support provides 24-hour-a-day, award-winning technical assistance. The Cisco Technical
Support Website on Cisco.com features extensive online support resources. In addition, Cisco Technical
Assistance Center (TAC) engineers provide telephone support. If you do not hold a valid Cisco service
contract, contact your reseller.
Cisco Technical Support Website
The Cisco Technical Support Website provides online documents and tools for troubleshooting and
resolving technical issues with Cisco products and technologies. The website is available 24 hours a day,
365 days a year, at this URL:
http://www.cisco.com/techsupport
Access to all tools on the Cisco Technical Support Website requires a Cisco.com user ID and password.
If you have a valid service contract but do not have a user ID or password, you can register at this URL:
http://tools.cisco.com/RPF/register/register.do
Note
Use the Cisco Product Identification (CPI) tool to locate your product serial number before submitting
a web or phone request for service. You can access the CPI tool from the Cisco Technical Support
Website by clicking the Tools & Resources link under Documentation & Tools. Choose Cisco Product
Identification Tool from the Alphabetical Index drop-down list, or click the Cisco Product
Identification Tool link under Alerts & RMAs. The CPI tool offers three search options: by product ID
or model name; by tree view; or for certain products, by copying and pasting show command output.
Search results show an illustration of your product with the serial number label location highlighted.
Locate the serial number label on your product and record the information before placing a service call.
Submitting a Service Request
Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3
and S4 service requests are those in which your network is minimally impaired or for which you require
product information.) After you describe your situation, the TAC Service Request Tool provides
recommended solutions. If your issue is not resolved using the recommended resources, your service
request is assigned to a Cisco TAC engineer. The TAC Service Request Tool is located at this URL:
http://www.cisco.com/techsupport/servicerequest
For S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone.
(S1 or S2 service requests are those in which your production network is down or severely degraded.)
Cisco TAC engineers are assigned immediately to S1 and S2 service requests to help keep your business
operations running smoothly.
To open a service request by telephone, use one of the following numbers:
Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)
EMEA: +32 2 704 55 55
USA: 1 800 553-2447
For a complete list of Cisco TAC contacts, go to this URL:
http://www.cisco.com/techsupport/contacts
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
xi
Preface
Obtaining Additional Publications and Information
Definitions of Service Request Severity
To ensure that all service requests are reported in a standard format, Cisco has established severity
definitions.
Severity 1 (S1)—Your network is “down,” or there is a critical impact to your business operations. You
and Cisco will commit all necessary resources around the clock to resolve the situation.
Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects of your
business operation are negatively affected by inadequate performance of Cisco products. You and Cisco
will commit full-time resources during normal business hours to resolve the situation.
Severity 3 (S3)—Operational performance of your network is impaired, but most business operations
remain functional. You and Cisco will commit resources during normal business hours to restore service
to satisfactory levels.
Severity 4 (S4)—You require information or assistance with Cisco product capabilities, installation, or
configuration. There is little or no effect on your business operations.
Obtaining Additional Publications and Information
Information about Cisco products, technologies, and network solutions is available from various online
and printed sources.
•
Cisco Marketplace provides a variety of Cisco books, reference guides, and logo merchandise. Visit
Cisco Marketplace, the company store, at this URL:
http://www.cisco.com/go/marketplace/
•
Cisco Press publishes a wide range of general networking, training and certification titles. Both new
and experienced users will benefit from these publications. For current Cisco Press titles and other
information, go to Cisco Press at this URL:
http://www.ciscopress.com
•
Packet magazine is the Cisco Systems technical user magazine for maximizing Internet and
networking investments. Each quarter, Packet delivers coverage of the latest industry trends,
technology breakthroughs, and Cisco products and solutions, as well as network deployment and
troubleshooting tips, configuration examples, customer case studies, certification and training
information, and links to scores of in-depth online resources. You can access Packet magazine at
this URL:
http://www.cisco.com/packet
•
iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies
learn how they can use technology to increase revenue, streamline their business, and expand
services. The publication identifies the challenges facing these companies and the technologies to
help solve them, using real-world case studies and business strategies to help readers make sound
technology investment decisions. You can access iQ Magazine at this URL:
http://www.cisco.com/go/iqmagazine
•
Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering
professionals involved in designing, developing, and operating public and private internets and
intranets. You can access the Internet Protocol Journal at this URL:
http://www.cisco.com/ipj
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
xii
OL-4681-01
Preface
Obtaining Additional Publications and Information
•
World-class networking training is available from Cisco. You can view current offerings at
this URL:
http://www.cisco.com/en/US/learning/index.html
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
xiii
Preface
Obtaining Additional Publications and Information
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
xiv
OL-4681-01
C H A P T E R
1
MSCs and SPA Product Overview
This chapter provides an introduction to the modular services cards (MSCs) and shared port
adapters (SPAs). It contains the following sections:
•
Introduction to MSCs and SPAs, page 1-1
•
MSC and SPA Compatibility, page 1-2
•
Modular Optics Compatibility, page 1-3
For software details for the specific MSCs and SPAs that are supported on the Cisco 7304 router, refer
to the companion publication, Cisco 7304 Router Modular Services Card and Shared Port Adapter
Software Configuration Guide.
Introduction to MSCs and SPAs
MSCs and SPAs are a carrier card and port adapter architecture to increase modularity, flexibility, and
density across Cisco Systems routers for network connectivity. This section describes the MSCs and
SPAs and provides some guidelines for their use.
Modular Service Cards
The following lists describes some of the general characteristics of an MSC:
•
An MSC is a carrier card that inserts into a router slot like a line card. It provides no network
connectivity on its own.
Note
The MSC-100 is the only carrier card currently available for SPAs on the Cisco 7304 router.
However, SPAs can be inserted into other carrier cards on other router platforms. For
information on carrier cards on other platforms, see the documentation for those platforms.
•
The only MSC currently available is the MSC-100, which contains two subslots used to house SPAs.
The SPA provides interface ports for network connectivity.
•
During normal operation, the MSC should reside in the router fully populated either with functional
SPAs in all subslots, or with a SPA blank filler plate inserted in any empty subslots.
•
An MSC supports online insertion and removal (OIR) with SPAs inserted in its subslots. SPAs also
can be inserted or removed independently from the MSC.
Cisco 7304 MSC and SPA Hardware Configuration Guide
OL-4681-01
1-1
Chapter 1
MSCs and SPA Product Overview
MSC and SPA Compatibility
Shared Port Adapters
The following list describes some of the general characteristics of a SPA:
•
A SPA is a modular type of port adapter that inserts into a subslot of a compatible MSC carrier card
to provide network connectivity and increased interface port density.
Figure 1-1
SPA Sizes for the Cisco 7304 Router
Front of MSC
129309
half-height SPA
•
Each SPA provides a certain number of connectors, or ports, that are the interfaces to one or more
networks. These interfaces can be individually configured using the Cisco IOS command-line
interface (CLI).
•
Either a SPA blank filler plate or a functional SPA should reside in every subslot of an MSC during
normal operation.
•
SPAs support online insertion and removal (OIR). They can be inserted or removed independently
from the MSC. MSCs also support online insertion and removal (OIR) with SPAs inserted in their
subslots.
MSC and SPA Compatibility
Table 1-1 shows the MSC that is supported in the Cisco 7304 router and the SPA that it supports.
Table 1-1
MSC and SPA Compatibility on the Cisco 7304 Router
SPA
MSC-100
4-Port 10/100 FastEthernet SPA (SPA-4FE-7304)
Yes
2-Port 10/100/1000 Gigabit Ethernet SPA (SPA-2GE-7304)
Yes
2-Port OC-3c/STM-1 POS SPA (SPA-2XOC3-POS)
Yes
4-Port OC-3c/STM-1 POS SPA (SPA-4XOC3-POS)
Yes
1-Port OC-12c/STM-4 POS SPA (SPA-1OC12-POS)
Yes
2-Port T3/E3 Serial SPA (SPA-2XT3/E3)
Yes
4-Port T3/E3 Serial SPA (SPA-4XT3/E3)
Yes
Cisco 7304 MSC and SPA Hardware Configuration Guide
1-2
OL-4681-01
Chapter 1
MSCs and SPA Product Overview
Modular Optics Compatibility
Modular Optics Compatibility
Some SPAs implement small form-factor pluggable (SFP) optical transceivers to provide network
connectivity. An SFPmodule is a fiber optic receptacle device that mounts flush with the front panel to
provide network connectivity.
Cisco Systems qualifies the SFP modules that can be used with SPAs.
Note
The SPAs will only accept the SFP modules listed as supported in this document. An SFP check is run
every time an SFP is inserted into a SPA and only SFP modules that pass this check will be usable.
Table 1-2 shows the types of optics modules that have been qualified for use with a SPA:
Table 1-2
SPA Optics Compatibility
SPA
2-Port Gigabit Ethernet SPA
2-Port and 4-Port OC-3c/STM-1 POS SPA
1-Port OC-12c/STM-4 POS SPA
Qualified Optics Modules
•
SFP-FCGE-S
•
SFP-FCGE-L
•
SFP-GE-Z
•
SFP-OC3-MM
•
SFP-OC3-SR
•
SFP-OC3-IR1
•
SFP-OC3-LR1
•
SFP-OC3-LR2
•
SFP-OC12-MM
•
SFP-OC12-SR
•
SFP-OC12-IR1
•
SFP-OC12-LR1
•
SFP-OC12-LR2
Cisco 7304 MSC and SPA Hardware Configuration Guide
OL-4681-01
1-3
Chapter 1
MSCs and SPA Product Overview
Modular Optics Compatibility
Cisco 7304 MSC and SPA Hardware Configuration Guide
1-4
OL-4681-01
C H A P T E R
2
Overview: Cisco 7304 Router Carrier Cards
This chapter describes the carrier cards that are supported on the Cisco 7304 router and contains the
following sections:
•
Carrier Card and SPA Compatibility, page 2-1
•
Carrier Card Summary, page 2-1
•
MSC-100 Overview, page 2-2
Carrier Card and SPA Compatibility
For information on carrier card and SPA compatibility, see the “MSC and SPA Compatibility” section
on page 1-2.
Carrier Card Summary
Summary descriptions of the carrier cards that are supported on the Cisco 7304 router are shown in
Table 2-1.
Table 2-1
Carrier Card Summary
Carrier Card Product Number
Description
Number of
SPAs
Minimum Cisco IOS
Release
MSC-100
Modular Services Card 100
2
Release 12.2(20)S2
7304-MSC-100
Cisco 7304 MSC and SPA Hardware Installation Guide
OL-4681-01
2-1
Chapter 2
Overview: Cisco 7304 Router Carrier Cards
MSC-100 Overview
Checking Hardware and Software Compatibility
To check the minimum software requirements of Cisco IOS software with the hardware installed on your
router, Cisco maintains the Software Advisor tool on Cisco.com. This tool does not verify whether
carrier cards or SPAs within a system are compatible, but it does provide the minimum Cisco IOS
requirements for individual hardware modules or components.
Note
Access to this tool is limited to users with Cisco.com login accounts.
To access Software Advisor, click Login at Cisco.com, type “Software Advisor” in the SEARCH box,
and click GO. Click the link for the Software Advisor tool.
Choose a product family or enter a specific product number to search for the minimum supported
software release needed for your hardware.
SPA Blank Filler Plates
SPA blanks are available to fill and unused SPA slot.
Note
When a SPA slot is not in use, a SPA blank filler plate must fill the empty slot to allow the router or
switch to conform to electromagnetic interference (EMI) emissions requirements and to allow proper
airflow across the SPAs. If you plan to install a new SPA in a slot that is not in use, you must first remove
the SPA blank filler plate.
MSC-100 Overview
The following sections describe the MSC-100:
•
Board Components, page 2-2
•
LEDs, page 2-4
•
Physical Specifications, page 2-5
•
Carrier Card Slot Locations on the Cisco 7304 Router, page 2-5
•
SPA Slot Numbering on the MSC-100, page 2-5
•
SPA Interface Addresses on MSCs, page 2-6
Board Components
The main MSC-100 board components are shown in Figure 2-1.
Cisco 7304 MSC and SPA Hardware Installation Guide
2-2
OL-4681-01
Chapter 2
Overview: Cisco 7304 Router Carrier Cards
MSC-100 Overview
Figure 2-1
MSC-100 Board—Overhead View
5
4
3
6
2
7
1
Flash memory
5
Temperature monitor
2
SRAM
6
FPGA
3
ASIC
7
SPA connector
4
Backplane connector
95717
1
Cisco 7304 MSC and SPA Hardware Installation Guide
OL-4681-01
2-3
Chapter 2
Overview: Cisco 7304 Router Carrier Cards
MSC-100 Overview
LEDs
The MSC-100 has four LEDs, as shown in Figure 2-2.
Figure 2-2
MSC-100 Faceplate
7304-MSC-100
OIR
OIR-SUBSLOT 0 SPA
OIR-SUBSLOT 1 SPA
7304 SPA CARRIER
111813
STATUS
MSC-100 LEDs are described in Table 2-2.
Table 2-2
MSC-100 LEDs
LED Label
Color
State
Meaning
OIR-SUBSLOT 0
SPA
Green
Offline
The SPA in subslot 0 is offline and can be removed.
Off
Online or
Offline
If the STATUS LED is green, the SPA in subslot 0 is online
and cannot be removed.
If the STATUS LED is off, the SPA in subslot 0 is offline.
OIR-SUBSLOT 1
SPA
OIR
STATUS
Green
Offline
The SPA in Subslot 1 is offline and can be removed.
Off
Online or
Offline
The SPA in subslot 1 is online and cannot be removed.
Green
Offline
The MSC-100 is offline and is ready to be removed.
Off
Online or
Offline
The MSC-100 is online and should not be removed.
Off
Off
The MSC-100 is offline.
Yellow
Powering
up or
powering
down
The MSC-100 is powering up or powering down.
Green
On
The MSC-100 is online.
If the STATUS LED is off , the SPA in subslot 1 is offline.
If the STATUS LED is off, the MSC is offline.
Cisco 7304 MSC and SPA Hardware Installation Guide
2-4
OL-4681-01
Chapter 2
Overview: Cisco 7304 Router Carrier Cards
MSC-100 Overview
Physical Specifications
The MSC-100 physical specifications are shown in Table 2-3.
Table 2-3
MSC-100 Physical Specifications
Description
Specifications
Physical Dimensions
2 in. x 8.35 in x 12.75 in (5.1 cm x 21.2 cm x 32.4 cm)
Shipping Weight
3 lbs. (1.37 kg)
Temperature—Operating
32 to 158°F (0 to 70°C)
Temperature—Storage
–4 to 158°F (–20 to 70°C)
Relative humidity
5 to 90 percent, noncondensing
Altitude—Operating
–500 to 10,000 ft.
Altitude—Storage
–1,000 to 30,000 ft.
Carrier Card Slot Locations on the Cisco 7304 Router
The MSC-100 can be installed in Cisco 7304 router module slots 2 through 5.
Figure 2-3
Module Slots on the Cisco 7304 Router
Slot 4
7300-2
OC3AT
M-MM
TX
OIR
0
Slot 5
RX
STATUS
2-PORT
OC3 ATM
TX
1
RX
MM
CARRIER
ALARM/
9K-10C
48
ACTIVE/
LOOPBAC
K
CARRIER
ALARM/
ACTIVE/
LOOPBAC
K
TX
OIR
RX
STATUS
1-PORT
OC48 POS
9K-40C
3/POS
w/ SMS
-MM
R
OIR
STATUS
4-POR
T OC3
0
1
POS w/
2
3
MM
CARRIER
ALARM/
70550
ACTIVE/
LOOPBA
CK
Slot 0
Slot 2
Slot 3
Slot 1
SPA Slot Numbering on the MSC-100
The MSC-100 accepts two single-height SPAs. The top subslot in the MSC is subslot 0 and the bottom
subslot is subslot 1.
Cisco 7304 MSC and SPA Hardware Installation Guide
OL-4681-01
2-5
Chapter 2
Overview: Cisco 7304 Router Carrier Cards
MSC-100 Overview
SPA Interface Addresses on MSCs
Interface addresses specify the physical location of each interface on a router or switch. Table 2-4
describes how to identify the interface addresses for SPAs supported on the MSC-100.
Table 2-4
Address Format
MSC
Address Format
Description
MSC-100
router-module-slot/subslot/SPA-port-number
Router module slot—2 through 5. Specifies
the slot on the Cisco 7304 router where the
MSC-100 is installed.
subslot—Top (0) or bottom (1) subslot.
Specifies the subslot in the MSC-100 that is
holding the SPA.
SPA-port-number—Varies. Specifies the port
number on the SPA to address.
Cisco 7304 MSC and SPA Hardware Installation Guide
2-6
OL-4681-01
C H A P T E R
3
Overview: Cisco 7304 Router Shared Port
Adapters
This chapter describes the shared port adapters (SPAs) that are supported on the Cisco 7304 router and
contains the following sections:
•
SPA Summary, page 3-1
•
Bandwidth Oversubscription, page 3-2
•
FastEthernet SPA Overview, page 3-2
•
GigabitEthernet SPA Overview, page 3-5
•
OC-3 POS SPA Overview, page 3-10
•
OC-12 POS SPA Overview, page 3-13
•
T3/E3 Serial SPA Overview, page 3-16
SPA Summary
Summary descriptions of the SPAs that are supported on the Cisco 7304 router are shown in Table 3-1.
Table 3-1
SPA Summary for Cisco 7304 Routers
Number
of Ports
Minimum Cisco IOS
Release
4-port 10/100
FastEthernet SPA
4
Release 12.2(20)S2
SPA-2GE-7304
2-port 10/100/1000
GigabitEthernet SPA
2
Release 12.2(20)S2
OC-3 SPA
SPA-2XOC3-POS
2-Port OC-3c/STM-1
POS SPA
2
Release 12.2(25)S3
OC-3 SPA
SPA-4XOC3-POS
4-Port OC-3c/STM-1
POS SPA
4
Release 12.2(25)S3
OC-12 SPA
SPA-1OC12-POS
1-Port OC-12c/STM-4
POS SPA
1
Release 12.2(25)S3
T3/E3 Serial SPA
SPA-2XT3/E3
2-Port T3/E3 Serial SPA
2
Release 12.2(25)S3
T3/E3 Serial SPA
SPA-4XT3/E3
4-Port T3/E3 Serial SPA
4
Release 12.2(25)S3
SPA
Product Number
Description
FastEthernet SPA
SPA-4FE-7304
GigabitEthernet
SPA
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
3-1
Chapter 3
Overview: Cisco 7304 Router Shared Port Adapters
Bandwidth Oversubscription
Checking Hardware and Software Compatibility
To check the minimum software requirements of Cisco IOS software with the hardware installed on your
router, Cisco maintains the Software Advisor tool on Cisco.com. This tool does not verify whether MSCs
or SPAs within a system are compatible, but it does provide the minimum Cisco IOS requirements for
individual hardware modules or components.
Note
Access to this tool is limited to users with Cisco.com login accounts.
To access Software Advisor, click Login at Cisco.com, type “Software Advisor” in the SEARCH box,
and click GO. Click the link for the Software Advisor tool.
Choose a product family or enter a specific product number to search for the minimum supported
software release needed for your hardware.
Bandwidth Oversubscription
For information on bandwidth oversubscription on the Cisco 7304 router, including information on how
SPAs and carrier cards impact the overall bandwidth of the router, see Bandwidth Information for Cisco
7304 Routers.
FastEthernet SPA Overview
The following sections describe the SPA-4FE-7304:
•
LEDs, page 3-2
•
Cables, Connectors, and Pinouts, page 3-3
LEDs
The SPA-4FE-7304 has the LEDs shown in Figure 3-1.
(RJ45)
(RJ45)
3
2
1
0
ST
SPA-4FE-7304
US
AT
95736
(RJ45)
3
(RJ45)
2
SPA-4FE-7304 Faceplate
1
0
Figure 3-1
The SPA-4FE-7304 LEDs are described in Table 3-2.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
3-2
OL-4681-01
Chapter 3
Overview: Cisco 7304 Router Shared Port Adapters
FastEthernet SPA Overview
Table 3-2
SPA-4FE-7304 LEDs
LED Label
Color
State
Meaning
STATUS
Green
On
The SPA is online.
Yellow
On
The SPA is receiving power and bootstrapping.
Off
Off
The SPA is offline and deactivated.
On
The port is enabled and the link is up.
Yellow
On
The port is enabled and the link is down.
Off
Off
The port is disabled.
Port Number Green
(0, 1, 2, or 3) 1
1. In this case, port number refers to the numbered LEDs on the SPA-4FE-7304 (0, 1, 2, or 3). Each LED number on the
FastEthernet SPA references a port on the SPA.
Cables, Connectors, and Pinouts
The interface connectors on the SPA-4FE-7304 are four individual RJ-45 receptacles. You can use all
four interface connectors simultaneously. Each connection supports IEEE 802.3 and Ethernet
10BASE-T interfaces compliant with appropriate standards. The RJ-45 connections require external
transceivers. Cisco Systems does not supply Category 5 unshielded twisted-pair (UTP) RJ-45 cables;
these cables are available commercially.
Figure 3-2 shows the RJ-45 connector. Table 3-3 lists the pinouts and signals for the RJ-45 connector.
RJ-45 Connections, Plug, and Receptacle
87654321
RJ-45 connector
Table 3-3
Note
H2936
Figure 3-2
RJ-45 Connector Pinout
Pin
Description
1
Transmit data + (TxD+)
2
TxD–
3
Receive data + (RxD+)
6
RxD–
Referring to the RJ-45 pinout in Table 3-3, proper common-mode line terminations should be used for
the unused Category 5 UTP cable pairs 4/5 and 7/8. Common-mode termination reduces the
contributions to electromagnetic interference (EMI) and susceptibility to common-mode sources. Wire
pairs 4/5 and 7/8 are actively terminated in the RJ-45 port circuitry in the SPA-4FE-7304.
Depending on your RJ-45 interface cabling requirements, use the pinouts in Figure 3-3 and Figure 3-4.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
3-3
Chapter 3
Overview: Cisco 7304 Router Shared Port Adapters
FastEthernet SPA Overview
Straight-Through Cable Pinout, RJ-45 Connection to a Hub or Repeater
Ethernet port
3 TxD+
3 RxD+
6 TxD–
6 RxD–
1 RxD+
1 TxD+
2 RxD–
2 TxD–
Figure 3-4
H7101
Hub or LAN switch
Crossover Cable Pinout, RJ-45 Connections Between Routers
Router
Router
3 TxD+
3 TxD+
6 TxD–
6 TxD–
1 RxD+
1 RxD+
2 RxD–
2 RxD–
101929
Figure 3-3
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
3-4
OL-4681-01
Chapter 3
Overview: Cisco 7304 Router Shared Port Adapters
GigabitEthernet SPA Overview
GigabitEthernet SPA Overview
The following sections describe the SPA-2GE-7304:
•
LEDs, page 3-5
•
Cables, Connectors, and Pinouts, page 3-5
•
SFP Module Cabling and Connection Equipment, page 3-9
LEDs
The SPA-2GE-7304 has three LEDs, as shown in Figure 3-5.
S
(RJ45)
1
(SFP)
0
(SFP)
1
0
ST
AT
U
ONLY USE ONE
0 AND 1 PORT
COMBINATION
SPA-2GE-7304
101827
(RJ45)
1
SPA-2GE-7304 Faceplate
0
Figure 3-5
The SPA-2GE-7304 LEDs are described in Figure 3-5.
Table 3-4
SPA-2GE-7304 LEDs
LED Label
Color
State
Meaning
STATUS
Green
On
The SPA is online.
Yellow
On
The SPA is receiving power and bootstrapping.
Off
Off
The SPA is offline and deactivated.
Green
On
The port is enabled and the link is up.
Yellow
On
The port is enabled and the link is down.
Off
Off
The port is disabled.
Port Number
(0 or 1) 1
1. In this case, port number refers to the numbered LEDs on the SPA-2GE-7304 (0 or 1). Each LED number on the
GigabitEthernet SPA references a port on the SPA.
Cables, Connectors, and Pinouts
The interface connectors on the SPA-2GE-7304 are two individual RJ-45 receptacles and two fiber optic
receivers that support SFPs. It is import to note that the SPA-2GE-7304 can only send and receive traffic
from two ports, port 0 and port 1. Each port can send and receive traffic using either the RJ-45 port or
the optical fiber connection.
The following sections describe the cable, connection, and pinout requirements for the SPA-2GE-7304:
•
RJ-45 Connectors, page 3-6
•
SFP Connections, page 3-7
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
3-5
Chapter 3
Overview: Cisco 7304 Router Shared Port Adapters
GigabitEthernet SPA Overview
RJ-45 Connectors
The SPA-2GE-7304 router has two RJ-45 ports for 10/100/1000 Ethernet/FastEthernet/GigabitEthernet
connections. The RJ-45 ports support IEEE 802.3ab (Gigabit Ethernet) and IEEE 802.3u (Fast Ethernet)
interfaces compliant with 10BASE-T, 100BASE-TX, and 1000BASE-T specifications.
The RJ-45 ports support standard straight-through and crossover Category 5 UTP cables with RJ-45
connectors. Cisco Systems does not supply Category 5 UTP cables; these cables are available
commercially.
Warning
To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network
voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some
LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables.
Figure 3-6 shows an RJ-45 connector. Table 3-5 lists the pinouts and signals for the RJ-45 port.
Figure 3-6
RJ-45 Port and Connector
1
1
57574
12345678
RJ-45 connector
Table 3-5
RJ-45 Receptacle Pinouts
Pin
GE Signal
1
Tx A+ 1
2
Tx A–
3
Rx B+ 2
4
Tx C+
5
Tx C–
6
Rx B–
7
Rx D+
8
Rx D–
1. TX DATA = Transmit Data
2. RX DATA = Receive Data
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
3-6
OL-4681-01
Chapter 3
Overview: Cisco 7304 Router Shared Port Adapters
GigabitEthernet SPA Overview
SFP Connections
The small form-factor pluggable (SFP) module is an input/output (I/O) device that plugs into the Gigabit
Ethernet optical slot on the SPA-2GE-7304, linking the port with a 1000BASE-X fiber-optic network.
An SFP module is shown in Figure 3-7.
Note
The SPA-2GE-7304 will only accept the SFP modules listed as supported in this document. An SFP
check is run every time an SFP is inserted into the SPA-2GE-7304 and only SFP modules that pass this
check will be usable by the SPA-2GE-7304.
SFP modules exist for technologies other than Gigabit Ethernet and for products other than the
SPA-2GE-7304. However, the information in this document pertains only to SFP modules that plug into
the SPA-2GE-7304 fiber-optic ports.
SFP Module
101310
Figure 3-7
The SFP module has a receiver port (RX) and a transmitter port (TX) that compose one optical interface.
Table 3-6, Table 3-7, and Table 3-8 provide SFP module information and specifications.
Table 3-6
SFP Module Options
SFP Module
Product Number
SFP Module
Description
SFP-FCGE-S
Short wavelength
(1000BASE-SX)
Contains a Class 1 laser of 850 nm for
1000BASE-SX (short wavelength) applications.
SFP-FCGE-L
Long wavelength/long haul
(1000BASE-LX/LH)
Contains a Class 1 laser of 1300 nm for
1000BASE-LX/LH (long wavelength)
applications.
SFP-GE-Z
Extended distance
(1000BASE-ZX)
Contains a Class 1 laser of 1550 nm for
1000BASE-ZX (extended wavelength)
applications.
Table 3-7
SFP Module Transmit Power, Receive Power, and Power Budget
Transmit Power
SFP Module
SFP-FCGE-S
Minimum
–9.5 dBm
Receive Power
Maximum
1
–4 dBm
1
Minimum
Maximum
–17 dBm
0 dBm
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
3-7
Chapter 3
Overview: Cisco 7304 Router Shared Port Adapters
GigabitEthernet SPA Overview
Table 3-7
SFP Module Transmit Power, Receive Power, and Power Budget
Transmit Power
SFP Module
Minimum
SFP-FCGE-L
–9.5 dBm
SFP-GE-Z
0 dBm
Receive Power
Maximum
2
–3 dBm
3
5 dBm
Minimum
Maximum
–19 dBm
–3 dBm
–23 dBm
–3 dBm
1. For fiber types 50/125 µm, NA = 0.20 fiber and 62.5/125 µm, NA = 0.275 fiber.
2. For fiber types 9/125 µm SMF.
3. For fiber types 9/125 µm SMF, 62.5/125 µm MMF, and 50/125
Table 3-8
µm MMF.
SFP Module Specifications
Specification
Description
Dimensions (H x W x D)
0.03 in x 0.53 in x 2.22 in (8.5 mm x 13.4mm x
56.5 mm)
Connectors
Multimode fiber-optic: LC-type connector
Single-mode fiber-optic: LC-type connector
Wavelength
SFP-FCGE-S: 770-860 nm
SFP-FCGE-L: 1270-1355 nm
SFP-GE-Z: 1500-1580 nm
Cabling distance
(maximum)
SFP-FCGE-S: 1804 feet (550 m)
SFP-FCGE-L: 6.2 miles (10 km)
SFP-GE-Z: 43.5 to 62.1 miles (70 to 100 km)
Operating temperature range
32 to 122 degrees F (0 to 50 degrees C)
Storage temperature range
-40 to 185 degrees F (-40 to 85 degrees C)
SFP-FCGE-S Modules
The 1000BASE-SX (short wavelength) module operates on standard multimode fiber-optic link spans of
up to 1804 feet (550 m). (See Table 3-9.)
SFP-FCGE-L Modules
The 1000BASE-LX/LH (long wavelength/long haul) module interfaces fully comply with the IEEE
802.3z 1000BASE-LX standard. However, their higher optical quality allows them to reach
6.2 miles (10 km) over single-mode fiber (SMF) versus the 3.1 miles (5 km) specified in the standard.
(See Table 3-9.)
SFP-GE-Z Modules
The 1000BASE-ZX (extended wavelength) module operates on ordinary single-mode fiber-optic link
spans of up to 43.5 miles (70 km). Link spans of up to 62.1 miles (100 km) are possible using premium
single-mode fiber or dispersion-shifted single-mode fiber (premium single-mode fiber has a lower
attenuation per unit length than ordinary single-mode fiber; dispersion-shifted single-mode fiber has
both lower attenuation and less dispersion).
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
3-8
OL-4681-01
Chapter 3
Overview: Cisco 7304 Router Shared Port Adapters
GigabitEthernet SPA Overview
The 1000BASE-ZX module must be coupled to single-mode fiber-optic cable, which is the type of cable
typically used in long-haul telecommunications applications. The 1000BASE-ZX module will not
operate correctly when coupled to multimode fiber, and it is not intended to be used in environments
where multimode fiber is frequently used (for example, building backbones, or horizontal cabling).
The 1000BASE-ZX module is intended to be used as a Physical Medium Dependent (PMD) component
for Gigabit Ethernet interfaces found on various switch and router products. It operates at a signaling
rate of 1250 Mbaud, transmitting and receiving 8B/10B encoded data.
When shorter lengths of single-mode fiber are used, it may be necessary to insert an in-line optical
attenuator in the link to avoid overloading the receiver.
•
Insert a 10-dB in-line optical attenuator between the fiber-optic cable plant and the receiving port
on the 1000BASE-ZX module at each end of the link whenever the fiber-optic cable span is less than
15.5 miles (25 km).
•
Insert a 5-dB in-line optical attenuator between the fiber-optic cable plant and the receiving port on
the 1000BASE-ZX module at each end of the link whenever the fiber-optic cable span is equal to or
greater than 15.5 miles (25 km) but less than 31 miles (50 km).
SFP Module Cabling and Connection Equipment
Table 3-9 provides cabling specifications for the SFP modules that can be installed on the
SPA-2GE-7304. Note that all SFP ports have LC-type connectors.
The minimum cable distance for the SFP-FCGE-S is 6.5 feet (2 m), and the minimum link distance for
the SFP-GE-Z is 6.2 miles (10 km) with an 8-dB attenuator installed at each end of the link. Without
attenuators, the minimum link distance for the SFP-GE-Z is 24.9 miles (40 km).
Table 3-9
SFP Module Port Cabling Specifications
SFP Modules
Wavelength
(nm)
SFP-FCGE-S
850
SFP-FCGE-L
SFP-GE-Z
1300
1550
Fiber Type
Core Size
(micron)
Modal
Bandwidth
(MHz/km)
Maximum
Cable Distance
MMF 1
62.5
160
722 ft (220 m)
62.5
200
902 ft (275 m)
50.0
400
1640 ft (500 m)
50.0
500
1804 ft (550 m)
62.5
500
1804 ft (550 m)
50.0
400
1804 ft (550 m)
50.0
500
1804 ft (550 m)
9/10
—
6.2 miles (10 km)
SMF
9/10
—
49.7 miles
(80 km)
SMF3
8
—
62.1 miles
(100 km)
2
MMF and
SMF
1. Multimode fiber (MMF) only.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
3-9
Chapter 3
Overview: Cisco 7304 Router Shared Port Adapters
OC-3 POS SPA Overview
2. A mode-conditioning patch cord is required.
When using the SFP-FCGE-L with 62.5-micron diameter MMF, you must install a mode-conditioning patch cord between the
SFP module and the MMF cable on both the transmit and the receive ends of the link when link distances are greater than 984 ft
(300 m).
We do not recommend using the SFP-FCGE-L and MMF with no patch cord for very short link distance (tens of meters). The
result could be an elevated bit error rate (BER).
3. Dispersion-shifted single-mode fiber-optic cable.
Note
The 1000BASE-ZX SFP modules provide an optical power budget of 21.5 dB. You should measure your
cable plant with an optical loss test set to verify that the optical loss of the cable plant (including
connectors and splices) is less than or equal to 21.5 dB. The optical loss measurement must be performed
with a 1550-nm light source.
CWDM SFPs
CWDM SFPs were first supported on the SPA-2GE-7304 in Cisco IOS Release 12.2(28)SB. CWDM
SFPs for the SPA-2GE-7304 come in eight wavelengths that range from 1470 nm to 1610 nm. Color
markings on the devices identify the wavelength to which the Gigabit Ethernet channel is mapped.
Table 3-10 lists the CWDM SFPs with their wavelengths and color codes that are supported on the
SPA-2GE-7304.
Table 3-10
CWDM SFP Wavelengths and Color Coding
SFP Product Number
Wavelength
Color Identifier
CWDM-SFP-1470=
Longwave 1470 nm laser, single mode
Gray
CWDM-SFP-1490=
Longwave 1490 nm laser, single mode
Violet
CWDM-SFP-1510=
Longwave 1510 nm laser, single mode
Blue
CWDM-SFP-1530=
Longwave 1530 nm laser, single mode
Green
CWDM-SFP-1550=
Longwave 1550 nm laser, single mode
Yellow
CWDM-SFP-1570=
Longwave 1570 nm laser, single mode
Orange
CWDM-SFP-1590=
Longwave 1590 nm laser, single mode
Red
CWDM-SFP-1610=
Longwave 1610 nm laser, single mode
Brown
For more detailed information on these CWDM SFP modules, see the Cisco CWDM GBIC and SFP
Solution Data Sheet.
OC-3 POS SPA Overview
The 2-Port and 4-Port OC-3c/STM-1 POS SPA is a single-height SPA that installs into one MSC
subslot. The OC-3c/STM-1 POS SPA with small form-factor pluggable (SFP) optical transceiver
modules provides SONET and SDH network connectivity with a per-port bandwidth of 155.52 Mbps.
For more information about SPA bandwidth, see the “Bandwidth Oversubscription” topic in this chapter.
For more information about SPAs and their compatibility with MSCs and modular optics, see the “MSC
and SPA Product Overview” chapter in this guide.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
3-10
OL-4681-01
Chapter 3
Overview: Cisco 7304 Router Shared Port Adapters
OC-3 POS SPA Overview
The following sections describe the 2-Port and 4-Port OC-3c/STM-1 POS SPA :
•
2-Port and 4-Port OC-3c/STM-1 POS SPA LEDs, page 3-11
•
2-Port and 4-Port OC-3c/STM-1 POS SPA Interface Specifications, page 3-11
•
2-Port and 4-Port OC-3c/STM-1 POS SPA Optical Transceiver Modules and Cables, page 3-12
2-Port and 4-Port OC-3c/STM-1 POS SPA LEDs
The 2-Port and 4-Port OC-3c/STM-1 POS SPA has three LEDs, as shown in Figure 3-8. There are two
LEDs for each port on the SPA, and one STATUS LED.
Figure 3-8
4-Port OC-3c/STM-1 POS SPA Faceplate
S
2
122938
2
3
ST
AT
U
L
A/
L
A/
L
A/
1
C/
A
C/
A
C/
A
C/
L
A/
0
A
1
3
1
C/A (Carrier/Alarm) LED
2
A/L (Active Loopback) LED
3
STATUS LED
The 2-Port and 4-Port OC-3c/STM-1 POS SPA LEDs are described in Table 3-11.
Table 3-11 2-Port and 4-Port OC-3c/STM-1 POS SPA LEDs
LED Label
Color
State
Meaning
C/A
Off
Off
Port is not enabled by software.
Green
On
Port is enabled by software, and there is a valid SONET signal
without any alarms.
Amber
On
Port is enabled by software, and there is at least one alarm.
Off
Off
Port is not enabled by software.
Green
On
Port is enabled by software, loopback is off.
Amber
On
Port is enabled by software, loopback is on.
Off
Off
SPA power is off.
Green
On
SPA is ready and operational.
Amber
On
SPA power is on and good; SPA is being configured.
A/L
STATUS
2-Port and 4-Port OC-3c/STM-1 POS SPA Interface Specifications
The framer processes incoming and outgoing SONET or SDH frames. The framer operates at
OC-3c/STM-1 line rates (155.52 Mbps).
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
3-11
Chapter 3
Overview: Cisco 7304 Router Shared Port Adapters
OC-3 POS SPA Overview
Packet data is transported with a user-configured encapsulation (such as Point-to-Point Protocol [PPP])
and is mapped into the STS-3c/STM-1 frame.
The 2-Port and 4-Port OC-3c/STM-1 POS SPA interface is compliant with the following RFCs:
•
RFC 1619, PPP over SONET/SDH
•
RFC 1662, PPP in HDLC-like Framing
The 2-Port and 4-Port OC-3c/STM-1 POS SPA also provides support for SNMP agent v1
(RFC 1155–1157) and RFC 1213:
•
RFC 1155, Structure and Identification of Management Information for TCP/IP-based Internets
•
RFC 1156, Management Information Base for Network Management of TCP/IP-Based Internets
•
RFC 1157, Simple Network Management Protocol (SNMP)
•
RFC 1213, Management Information Base (MIB) for Network Management of TCP/IP-Based
Internets:MIB II.
2-Port and 4-Port OC-3c/STM-1 POS SPA Optical Transceiver Modules and
Cables
The 2-Port and 4-Port OC-3c/STM-1 POS SPA uses a small form-factor pluggable (SFP) optical
transceiver module installed in each port for SONET and SDH single-mode and multimode optical fiber
connection (See Figure 3-9).
Cisco Systems qualifies the optics that are approved for use with its SPAs. The 2-Port and 4-Port
OC-3c/STM-1 POS SPA supports the following types of optical transceiver modules:
•
Multimode (MM) SFP module—SFP-OC3-MM
•
Short reach (SR) SFP module—SFP-OC3-SR
•
Intermediate reach (IR) SFP module (15 km)—SFP-OC3-IR1
•
Long reach (LR) SFP module (40 km)—SFP-OC3-LR1
•
LR SFP module (80 km)—SFP-OC3-LR2
SFP Optics Module
127158
Figure 3-9
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
3-12
OL-4681-01
Chapter 3
Overview: Cisco 7304 Router Shared Port Adapters
OC-12 POS SPA Overview
The SFP optical transceiver modules used with the 2-Port and 4-Port OC-3c/STM-1 POS SPA provide
the following optical fiber options:
•
Multimode—155-Mbps, OC-3c/STM-1 optical fiber (SONET STS-3c or SDH STM-1)
Use a multimode optical fiber that has a core/cladding diameter of 62.5/125 microns.
•
Single-mode—155-Mbps, OC-3c/STM-1 optical fiber (SONET STS-3c or SDH STM-1)
Use a single-mode optical fiber that has a modal-field diameter of 8.7 ± 0.5 microns. (Nominal
diameter is approximately 10/125 microns.)
For single-mode and multimode optical fiber connections, you can use either a duplex LC-type cable
(see Figure 3-10) or two simplex LC-type cables, one for transmit (TX) and one for receive (RX).
Use single-mode (for intermediate- or long-reach configurations) or multimode optical fiber cable to
connect your router to a network or to connect two OC-3c/STM-1-equipped routers back-to-back.
Long-range SFP optical transceiver modules (for long-reach configurations) cannot be connected
back-to-back without using an attenuator between the two of them.
Figure 3-10 LC-Type Cable
//
RX
//
84929
//
TX
OC-12 POS SPA Overview
The 1-Port OC-12c/STM-4 POS SPA is single-height SPA that installs into one MSC subslot. The 1-Port
OC-12c/STM-4 POS SPA with a small form-factor pluggable (SFP) optical transceiver module provides
SONET and SDH network connectivity with a bandwidth of 622.08 Mbps.
For more information about SPA bandwidth, see the “Bandwidth Oversubscription” topic in this chapter.
For more information about SPAs and their compatibility with MSCs and modular optics, see the “MSC
and SPA Product Overview” chapter in this guide.
The following sections describe the 1-Port OC-12c/STM-4 POS SPA:
•
1-Port OC-12c/STM-4 POS SPA LEDs, page 3-14
•
1-Port OC-12c/STM-4 POS SPA Interface Specifications, page 3-14
•
1-Port OC-12c/STM-4 POS SPA SFP Optical Transceiver Modules and Cables, page 3-15
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
3-13
Chapter 3
Overview: Cisco 7304 Router Shared Port Adapters
OC-12 POS SPA Overview
1-Port OC-12c/STM-4 POS SPA LEDs
The 1-Port OC-12c/STM-4 POS SPA has three types of LEDs. There are two LEDs for each port on the
SPA, and one STATUS LED. Figure 3-11 shows an example of these LEDs on a 1-Port OC-12c/STM-4
POS SPA.
Figure 3-11 1-Port OC-12c/STM-4 POS SPA Faceplate
A/
L
ST
AT
U
S
C/
A
1
129137
0
SPA-1XOC12-POS
3
2
1
C/A (Carrier/Alarm) LED
2
A/L (Active Loopback) LED
3
STATUS LED
The 1-Port OC-12c/STM-4 POS SPA LEDs are described in Table 3-12.
Table 3-12 1-Port OC-12c/STM-4 POS SPA LEDs
LED Label
Color
State
Meaning
C/A
Off
Off
Port is not enabled by software.
Green
On
Port is enabled by software, and there is a valid SONET signal
without any alarms.
Amber
On
Port is enabled by software, and there is at least one alarm.
Off
Off
Port is not enabled by software.
Green
On
Port is enabled by software, loopback is off.
Amber
On
Port is enabled by software, loopback is on.
Off
Off
SPA power is off.
Green
On
SPA is ready and operational.
Amber
On
SPA power is on and good; SPA is being configured.
A/L
STATUS
1-Port OC-12c/STM-4 POS SPA Interface Specifications
The framer processes incoming and outgoing SONET or SDH frames. The framer operates at
OC-12c/STM-4 line rates (622.08 Mbps).
Packet data is transported with a user-configured encapsulation (such as Point-to-Point Protocol [PPP])
and is mapped into the STS-12c/STM-4 frame.
The 1-Port OC-12c/STM-4 POS SPA interface is compliant with the following RFCs:
•
RFC 1619, PPP over SONET/SDH
•
RFC 1662, PPP in HDLC-like Framing
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
3-14
OL-4681-01
Chapter 3
Overview: Cisco 7304 Router Shared Port Adapters
OC-12 POS SPA Overview
The 1-Port OC-12c/STM-4 POS SPA also provides support for SNMP v1 agent (RFC 1155–1157) and
RFC 1213:
•
RFC 1155, Structure and Identification of Management Information for TCP/IP-based Internets
•
RFC 1156, Management Information Base for Network Management of TCP/IP-Based Internets
•
RFC 1157, Simple Network Management Protocol (SNMP)
•
RFC 1213, Management Information Base (MIB) for Network Management of TCP/IP-Based
Internets:MIB II.
1-Port OC-12c/STM-4 POS SPA SFP Optical Transceiver Modules and Cables
The POS SPA uses a small form-factor pluggable (SFP) optical transceiver module installed in each port
for SONET and SDH single-mode and multimode optical fiber connection (see Figure 3-12).
Cisco Systems qualifies the optics that are approved for use with its SPAs. The 1-Port OC-12c/STM-4
POS SPA supports the following types of optical transceiver modules:
•
Multimode (MM) SFP module—SFP-OC12-MM
•
Short reach (SR) SFP module—SFP-OC12-SR
•
Intermediate reach (IR) SFP module (15 km)—SFP-OC12-IR1
•
Long reach (LR) SFP module (40 km)—SFP-OC12-LR1
•
LR SFP module (80 km)—SFP-OC12-LR2
127158
Figure 3-12 SFP Optics Module
The SFP optical transceiver modules used with the POS SPAs provide the following optical fiber
options:
•
Multimode—622.08-Mbps, OC-12 optical fiber (SONET STS-12c or SDH STM-4)
Use a multimode optical fiber that has a core/cladding diameter of 62.5/125 microns.
•
Single-mode—622.08-Mbps, OC-12 optical fiber (SONET STS-12c or SDH STM-4)
Use a single-mode optical fiber that has a modal-field diameter of 8.7 ±0.5 microns. (Nominal
diameter is approximately 10/125 microns.)
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
3-15
Chapter 3
Overview: Cisco 7304 Router Shared Port Adapters
T3/E3 Serial SPA Overview
For single-mode and multimode optical fiber connections, you can use either a duplex LC-type cable
(see Figure 3-13) or two simplex LC-type cables, one for transmit (TX) and one for receive (RX).
Use single-mode (for intermediate- or long-reach configurations) or multimode optical fiber cable to
connect your router to a network or to connect two 1-Port OC-12c/STM-4 POS SPA-equipped routers
back to back.
Long-range SFP optical transceiver modules (for long-reach configurations) cannot be connected
back-to-back without using an attenuator between the two of them.
Figure 3-13 LC-Type Cable
//
RX
//
84929
//
TX
T3/E3 Serial SPA Overview
The following sections describe the 2-Port and 4-Port T3/E3 Serial SPA:
•
2-Port and 4-Port T3/E3 Serial SPA LEDs, page 3-16
•
2-Port and 4-Port T3/E3 Serial SPA Interface Specifications, page 3-17
•
2-Port and 4-Port T3/E3 Serial SPA Cables and Connectors, page 3-17
2-Port and 4-Port T3/E3 Serial SPA LEDs
The 2-Port and 4-Port T3/E3 Serial SPA has three types of LEDs. There are two LEDs for each port on
the SPA, and one STATUS LED. Figure 3-14 shows an example of these LEDs on a 4-Port T3/E3 Serial
SPA.
Figure 3-14 4-Port T3/E3 Serial SPA Faceplate
2
ST
AT
U
S
3
RX
A
C/
C/
A/
L
TX
A
2
RX
TX
A/
L
1
RX
A
A/
L
4
SPA-4XT3/E3
5
116851
3
TX
RX
C/
A/
L
TX
C/
A
0
1
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
3-16
OL-4681-01
Chapter 3
Overview: Cisco 7304 Router Shared Port Adapters
T3/E3 Serial SPA Overview
1
C/A (Carrier/Alarm) LED
4
RX (Receive) connector
2
A/L (Active Loopback) LED
5
STATUS LED
3
TX (Transmit) connector
The 2-Port and 4-Port T3/E3 Serial SPA LEDs are described in Table 3-13.
Table 3-13 2-Port and 4-Port T3/E3 Serial SPA LEDs
LED Label
Color
State
Meaning
C/A
Off
Off
Port is not enabled by software.
Green
On
Port is enabled by software, and there is a valid E3 or T3 signal
without any alarms.
Amber
On
Port is enabled by software, and there is at least one alarm.
Off
Off
Port is not enabled by software.
Green
On
Port is enabled by software, loopback is off.
Amber
On
Port is enabled by software, loopback is on.
Off
Off
SPA power is off.
Amber
On
SPA power is on and good, and the SPA is being configured.
Green
On
SPA is ready and operational.
A/L
STATUS
2-Port and 4-Port T3/E3 Serial SPA Interface Specifications
The framer processes incoming and outgoing T3 (cbit, m13/m23, and unframe) and E3 (g751, g832, and
unframe) frames. The framer operates at T3/E3 line rates (44.2/34.0 Mbps) depending on which mode
it is configured in.
Packet data is transported with a user-configurable encapsulation (such as Point-to-Point Protocol [PPP]
or High-Level Data Link Control [HDLC]), and is mapped to T3 and E3 frames. The encapsulations add
transport overhead to the packet of data frames before transporting, and are stripped when a packet is
transported to the far end.
The T3/E3 SPA interface is compliant with ANSI and Telco standards. The interface also provides
support for Management Information Base (MIB) (RFC 2496) and T1.231.
2-Port and 4-Port T3/E3 Serial SPA Cables and Connectors
The interface connectors on the 2-Port and 4-Port T3/E3 Serial SPA are 75-ohm coaxial Siemax types,
with one connector and cable for transmit (TX) and one for receive (RX).
The following cables can be used with the 2-Port and 4-Port T3/E3 Serial SPA. The cables have BNC
on one end and the Siemax connectors on the other.
•
CAB-T3E3-RF-BNC-M (T3 or E3 Cable, 1.0/2.3 RF to BNC-Male, 10 Feet )
•
CAB-T3E3-RF-BNC-F(T3 or E3 Cable, 1.0/2.3 RF to BNC-Female, 10 Feet )
•
CAB-T3E3-RF-OPEN (T3 or E3 Cable, 1.0/2.3 RF to BNC-Open end, 10 Feet )
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
3-17
Chapter 3
Overview: Cisco 7304 Router Shared Port Adapters
T3/E3 Serial SPA Overview
Note
The Cisco cable part numbers are 72-4124-01 ( with male BNC end) and 72-4131-01 (with female BNC
end).
Figure 3-14 shows the connectors on the 4-Port T3/E3 Serial SPA, and Table 3-14 describes the signal
descriptions for these connectors.
Table 3-14 2-Port and 4-Port T3/E3 Serial SPA Connectors
Connector Label
Meaning
TX
Transmitted signals appear on the center contact, and the outer shield is ground
for the 75-ohm RG-59 coaxial cable you attach to the TX BNC connector.
RX
Received signals appear on the center contact, and the outer shield is ground for
the 75-ohm RG-59 coaxial cable you attach to the RX BNC connector.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
3-18
OL-4681-01
C H A P T E R
4
Preparing to Install a Modular Services Card or a
Shared Port Adapter
This chapter describes the general equipment, safety, and site preparation requirements for installing
MSCs and SPAs. This chapter contains the following sections:
•
Required Tools and Equipment, page 4-1
•
Safety Guidelines, page 4-1
•
Laser/LED Safety, page 4-16
Required Tools and Equipment
You need the following tools and parts to install MSCs and SPAs. If you need additional equipment,
contact a service representative for ordering information.
•
MSC-100 (7304-MSC-100)
•
Shared port adapters (SPAs)
•
Number 2 Phillips or a 3/16-inch flat-blade screwdriver
•
Your own electrostatic discharge (ESD)-prevention equipment or the disposable grounding wrist
strap supplied with the MSC or SPA
•
Antistatic mat
•
Antistatic container
Safety Guidelines
This section provides safety guidelines that you should follow when working with any equipment that
connects to electrical power or telephone wiring.
Safety Warnings
Safety warnings appear throughout this publication in procedures that, if performed incorrectly, might
harm you. A warning symbol precedes each warning statement.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
4-1
Chapter 4
Preparing to Install a Modular Services Card or a Shared Port Adapter
Safety Guidelines
Statement 1001—Work During Lightning Activity
Warning
Waarschuwing
Varoitus
Do not work on the system or connect or disconnect cables during periods of lightning activity.
Statement 1001
Tijdens onweer dat gepaard gaat met bliksem, dient u niet aan het systeem te werken of kabels aan
te sluiten of te ontkoppelen.
Älä työskentele järjestelmän parissa äläkä yhdistä tai irrota kaapeleita ukkosilmalla.
Attention
Ne pas travailler sur le système ni brancher ou débrancher les câbles pendant un orage.
Warnung
Arbeiten Sie nicht am System und schließen Sie keine Kabel an bzw. trennen Sie keine ab, wenn
es gewittert.
Avvertenza
Non lavorare sul sistema o collegare oppure scollegare i cavi durante un temporale con fulmini.
Advarsel
Utfør aldri arbeid på systemet, eller koble kabler til eller fra systemet når det tordner eller lyner.
Aviso
¡Advertencia!
Varning!
Não trabalhe no sistema ou ligue e desligue cabos durante períodos de mau tempo (trovoada).
No operar el sistema ni conectar o desconectar cables durante el transcurso de descargas
eléctricas en la atmósfera.
Vid åska skall du aldrig utföra arbete på systemet eller ansluta eller koppla loss kablar.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
4-2
OL-4681-01
Chapter 4
Preparing to Install a Modular Services Card or a Shared Port Adapter
Safety Guidelines
Statement 1008—Class 1 Laser Product
Warning
Waarschuwing
Varoitus
Class 1 laser product. Statement 1008
Klasse-1 laser produkt.
Luokan 1 lasertuote.
Attention
Produit laser de classe 1.
Warnung
Laserprodukt der Klasse 1.
Avvertenza
Prodotto laser di Classe 1.
Advarsel
Laserprodukt av klasse 1.
Aviso
Produto laser de classe 1.
¡Advertencia!
Varning!
Aviso
Advarsel
Producto láser Clase I.
Laserprodukt av klass 1.
Produto a laser de classe 1.
Klasse 1 laserprodukt.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
4-3
Chapter 4
Preparing to Install a Modular Services Card or a Shared Port Adapter
Safety Guidelines
Statement 1030—Equipment Installation
Warning
Waarschuwing
Varoitus
Only trained and qualified personnel should be allowed to install, replace, or service
this equipment. Statement 1030
Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door bevoegd
geschoold personeel.
Tämän laitteen saa asentaa, vaihtaa tai huoltaa ainoastaan koulutettu ja laitteen
tunteva henkilökunta.
Attention
Il est vivement recommandé de confier l'installation, le remplacement et la maintenance de ces
équipements à des personnels qualifiés et expérimentés.
Warnung
Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem, qualifiziertem
Personal gestattet werden.
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Questo apparato può essere installato, sostituito o mantenuto unicamente da un personale
competente.
Bare opplært og kvalifisert personell skal foreta installasjoner, utskiftninger eller service på
dette utstyret.
Apenas pessoal treinado e qualificado deve ser autorizado a instalar, substituir ou fazer a revisão
deste equipamento.
Solamente el personal calificado debe instalar, reemplazar o utilizar este equipo.
Endast utbildad och kvalificerad personal bör få tillåtelse att installera, byta ut eller reparera
denna utrustning.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
4-4
OL-4681-01
Chapter 4
Preparing to Install a Modular Services Card or a Shared Port Adapter
Safety Guidelines
Aviso
Advarsel
Somente uma equipe treinada e qualificada tem permissão para instalar, substituir ou dar
manutenção a este equipamento.
Kun uddannede personer må installere, udskifte komponenter i eller servicere dette udstyr.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
4-5
Chapter 4
Preparing to Install a Modular Services Card or a Shared Port Adapter
Safety Guidelines
Statement 1031—EU Public Network Port
Warning
If the symbol of suitability with an overlaid cross appears above a port, you must not connect the
port to a public network that follows the European Union standards. Connecting the port to this type
of public network can cause severe personal injury or can damage the unit. Statement 1031
Waarschuwing
Als er een geschiktheidssymbool met een overgetrokken kruis boven een poort aanwezig is, mag u
deze poort niet op een openbaar netwerk aansluiten dat aan de normen van de Europese Unie
voldoet. Als u de poort op een dergelijk openbaar netwerk aansluit, kan dit ernstig lichamelijk letsel
veroorzaken of schade aan de eenheid.
Varoitus
Jos portin yläpuolelle ilmestyy soveltuvuussymboli, jonka päällä on rasti, porttia ei saa liittää
Euroopan unionin standardien mukaiseen julkiseen verkkoon. Jos portti liitetään tällaiseen
julkiseen verkkoon, seurauksena voi olla henkilövahinko tai laitteen vaurioituminen.
Attention
Si le symbole de capacité barré d'une croix apparaît au-dessus d'un port, il est vivement
recommandé de ne pas connecter ce port à un réseau public aux normes de l'Union Européenne.
Connecter ce port à ce type de réseau public peut causer de graves accidents ou endommager
l'unité.
Warnung
Wenn oberhalb des Ports das Eignungssymbol mit einem Kreuz darüber erscheint, dürfen Sie den
Port nicht an ein öffentliches Netz anschließen, das den Standards der Europäischen Gemeinschaft
folgt. Das Anschließen des Port an ein solches Netz kann zu schweren Verletzungen führen oder die
Einheit beschädigen.
Avvertenza
Se sopra una porta è riportato il simbolo di idoneità sbarrato, significa che la porta non può essere
collegata a una rete pubblica a norma UE. Collegando la porta a tale rete pubblica si possono
correre seri rischi e provocare danni all'unità.
Advarsel
Hvis symbolet for anvendelse med et kryss over vises over en utgang, skal utgangen ikke tilkobles
et offentlig nettverk som følger EU-standardene. Hvis utgangen kobles til denne typen offentlig
nettverk, kan det medføre alvorlig personskade eller skade på enheten.
Aviso
Se o símbolo de adequação com uma cruz sobreposta aparecer acima de uma porta, não conecte a
porta a uma rede pública que obedece aos padrões da União Européia. A conexão da porta a este
tipo de rede pública pode causar danos físicos ao operador ou danificar a unidade.
¡Advertencia!
Varning!
Si aparece el símbolo de idoneidad con una cruz sobrepuesta encima de un puerto, no debe
conectarlo a una red pública que siga los estándares de la Unión Europea. Si conecta el puerto a
este tipo de red puede lesionarse o dañar la unidad.
Om lämplighetssymbolen med ett överlagt kors visas ovanför en port, får porten inte anslutas till ett
offentligt nätverk av EU-standard. Om porten ansluts till denna typ av offentligt nätverk kan det
orsaka allvarlig personskada eller skada enheten.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
4-6
OL-4681-01
Chapter 4
Preparing to Install a Modular Services Card or a Shared Port Adapter
Safety Guidelines
Statement 1041—Disconnecting Telephone-Network Cables
Warning
Waarschuwing
Varoitus
Before opening the unit, disconnect the telephone-network cables to avoid contact with
telephone-network voltages. Statement 1041
Voordat u de eenheid opent, dient u de verbinding met het telefoonnetwerk te verbreken door de
kabels te ontkoppelen om zo contact met telefoonnetwerk-spanning te vermijden.
Vältä joutumista kosketuksiin puhelinverkkojännitteiden kanssa irrottamalla puhelinverkoston
kaapelit ennen yksikön aukaisemista.
Attention
Pour éviter tout risque de choc électrique (tensions présentes dans l'unité), débranchez les câbles
du réseau téléphonique AVANT d'ouvrir l'unité.
Warnung
Bevor Sie das Gerät öffnen, ziehen Sie die Telefonnetzkabel aus der Verbindung, um Kontakt mit
Telefonnetzspannungen zu vermeiden.
Avvertenza
Advarsel
Prima di aprire l'unità, scollegare i cavi della rete telefonica per evitare di entrare in contatto con
la tensione di rete.
Før enheten åpnes, skal kablene for telenettet kobles fra for å unngå å komme i kontakt med
spenningen i telenettet.
Aviso
Antes de abrir a unidade, desligue os cabos da rede telefónica para evitar contacto com a tensão da
respectiva rede.
¡Advertencia!
Antes de abrir la unidad, desconectar el cableado dirigido a la red telefónica para evitar contacto
con voltajes de la propia red.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
4-7
Chapter 4
Preparing to Install a Modular Services Card or a Shared Port Adapter
Safety Guidelines
Varning!
Koppla loss ledningarna till telefonnätet innan du öppnar enheten så att kontakten med
telefonnätsspänningen bryts.
Statement 1043—Installation Hazard
Warning
This equipment must be installed and maintained by service personnel as defined by AS/NZS 3260.
Incorrectly connecting this equipment to a general-purpose outlet could be hazardous. The
telecommunications lines must be disconnected 1) before unplugging the main power connector or
2) while the housing is open, or both. Statement 1043
Waarschuwing
Deze apparatuur dient geïnstalleerd en onderhouden te worden door onderhoudspersoneel zoals
gedefinieerd door AS/NZS 3260. Als deze uitrusting onjuist op een stopcontact voor algemeen
gebruik wordt aangesloten, kan dit gevaarlijk zijn. De telecommunicatielijnen dienen ontkoppeld te
worden 1) voordat de stekker naar de hoofdstroomtoevoer eruit genomen wordt of 2) terwijl de
behuizing open is, of in beide gevallen.
Varoitus
Huoltohenkilöstön on asennettava ja huollettava tämä laite AS/NZS 3260:n määräysten mukaisesti.
Laitteen virheellinen kytkeminen yleispistorasiaan voi aiheuttaa vaaratilanteen.
Tietoliikennejohdot on irrotettava 1) ennen kuin päävirtaliitin irrotetaan pistorasiasta ja/tai 2) kun
kotelo on auki.
Attention
Cet équipement ne doit être installé et entretenu que par du personnel d'entretien conformément à
la réglementation AS/NZS 3260. Un branchement incorrect de cet équipement à une prise de courant
peut créer une situation dangereuse. Les lignes de télécommunications doivent être déconnectées
soit 1) avant de débrancher le connecteur d'alimentation principal, soit 2) lorsque le boîtier est
ouvert, soit les deux les deux à la fois.
Warnung
Dieses Gerät darf nur von ausgebildetem Personal installiert und gewartet werden (lt. Definition in
AS/NZS 3260). Fälschliches Anschließen des Geräts an eine normale Steckdose kann gefährlich
sein. Die Telekommunikationsleitungen dürfen nicht angeschlossen sein, wenn 1. der Netzstecker
herausgezogen wird oder 2. das Gehäuse geöffnet ist oder beides zutrifft.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
4-8
OL-4681-01
Chapter 4
Preparing to Install a Modular Services Card or a Shared Port Adapter
Safety Guidelines
Avvertenza
Questo apparecchio deve essere installato e mantenuto in efficienza esclusivamente da personale
tecnico che soddisfi i requisiti specificati nelle norme AS/NZS 3260. Il collegamento errato di questo
apparecchio ad una presa di uso generale può essere pericoloso. Le linee di telecomunicazione
vanno scollegate prima di scollegare la spina dell'alimentazione di rete e/o mentre l'involucro
è aperto.
Advarsel
Dette utstyret må monteres og vedlikeholdes av vedlikeholdspersonell i henhold til AS/NZS 3260.
Feil tilkobling av dette utstyret til et vanlig strømuttak kan medføre fare.
Telekommunikasjonslinjene må være frakoblet 1) før strømledningen trekkes ut av kontakten eller
2) mens huset er åpent, eller begge deler.
Aviso
A instalação e a manutenção deste equipamento devem ser realizadas por pessoal da assistência,
conforme definido na norma AS/NZS 3260. A ligação incorreta deste equipamento a uma tomada de
utilização geral poderá ser perigosa. As linhas de telecomunicações têm de estar desligadas 1)
antes de desligar a ligação da corrente principal, e/ou 2) enquanto a caixa de eletricidade estiver
aberta.
¡Advertencia!
Sólo el personal de servicio puede instalar y mantener este equipo, según lo estipulado en AS/NZS
3260. La conexión incorrecta de este equipo a una toma o receptáculo de tipo general podría resultar
peligrosa. Las líneas de telecomunicaciones deben desconectarse 1) antes de desenchufar el
conector principal de energía, 2) mientras la caja esté abierta o en ambos casos.
Varning!
Denna utrustning måste installeras och underhållas av servicepersonal enligt AS/NZS 3260. Felaktig
anslutning av denna utrustning till ett vanligt vägguttag kan medföra fara. Teleledningarna måste
kopplas från innan väggkontakten dras ut eller innan höljet tas av eller i båda fallen.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
4-9
Chapter 4
Preparing to Install a Modular Services Card or a Shared Port Adapter
Safety Guidelines
Statement 1056—Unterminated Fiber Cable
Warning
Invisible laser radiation may be emitted from the end of the unterminated fiber cable or connector.
Do not view directly with optical instruments. Viewing the laser output with certain optical
instruments (for example, eye loupes, magnifiers, and microscopes) within a distance of 100 mm may
pose an eye hazard. Statement 1056
Waarschuwing
Er kunnen onzichtbare laserstralen worden uitgezonden vanuit het uiteinde van de onafgebroken
vezelkabel of connector. Niet in de straal kijken of deze rechtstreeks bekijken met optische
instrumenten. Als u de laseruitvoer met bepaalde optische instrumenten bekijkt (zoals bijv. een
oogloep, vergrootgras of microscoop) binnen een afstand van 100 mm kan dit gevaar voor uw ogen
opleveren.
Varoitus
Päättämättömän kuitukaapelin tai -liittimen päästä voi tulla näkymätöntä lasersäteilyä. Älä tuijota
sädettä tai katso sitä suoraan optisilla välineillä. Lasersäteen katsominen tietyillä optisilla
välineillä (esim. suurennuslasilla tai mikroskoopilla) 10 cm:n päästä tai sitä lähempää voi olla
vaarallista silmille.
Attention
Des émissions de radiations laser invisibles peuvent se produire à l’extrémité d’un câble en fibre ou
d’un raccord sans terminaison. Ne pas fixer du regard le rayon ou l’observer directement avec des
instruments optiques. L’observation du laser à l’aide certains instruments optiques (loupes et
microscopes) à une distance inférieure à 100 mm peut poser des risques pour les yeux.
Warnung
Eine unsichtbare Laserstrahlung kann vom Ende des nicht angeschlossenen Glasfaserkabels oder
Steckers ausgestrahlt werden. Nicht in den Laserstrahl schauen oder diesen mit einem optischen
Instrument direkt ansehen. Ein Betrachten des Laserstrahls mit bestimmten optischen Instrumenten,
wie z.B. Augenlupen, Vergrößerungsgläsern und Mikroskopen innerhalb eines Abstands von 100 mm
kann für das Auge gefährlich sein.
Avvertenza
L’estremità del connettore o del cavo ottico senza terminazione può emettere radiazioni laser
invisibili. Non fissare il raggio od osservarlo in modo diretto con strumenti ottici. L’osservazione del
fascio laser con determinati strumenti ottici (come lupette, lenti di ingrandimento o microscopi)
entro una distanza di 100 mm può provocare danni agli occhi.
Advarsel
Usynlig laserstråling kan emittere fra enden av den ikke-terminerte fiberkabelen eller koblingen.
Ikke se inn i strålen og se heller ikke direkte på strålen med optiske instrumenter. Observering av
laserutgang med visse optiske instrumenter (for eksempel øyelupe, forstørrelsesglass eller
mikroskoper) innenfor en avstand på 100 mm kan være farlig for øynene.
Aviso
Radiação laser invisível pode ser emitida pela ponta de um conector ou cabo de fibra não terminado.
Não olhe fixa ou diretamente para o feixe ou com instrumentos ópticos. Visualizar a emissão do
laser com certos instrumentos ópticos (por exemplo, lupas, lentes de aumento ou microscópios) a
uma distância de 100 mm pode causar riscos à visão.
¡Advertencia!
El extremo de un cable o conector de fibra sin terminación puede emitir radiación láser invisible.
No se acerque al radio de acción ni lo mire directamente con instrumentos ópticos. La exposición
del ojo a una salida de láser con determinados instrumentos ópticos (por ejemplo, lupas y
microscopios) a una distancia de 100 mm puede comportar lesiones oculares.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
4-10
OL-4681-01
Chapter 4
Preparing to Install a Modular Services Card or a Shared Port Adapter
Safety Guidelines
Varning!
Osynlig laserstrålning kan komma från änden på en oavslutad fiberkabel eller -anslutning. Titta inte
rakt in i strålen eller direkt på den med optiska instrument. Att titta på laserstrålen med vissa
optiska instrument (t.ex. lupper, förstoringsglas och mikroskop) från ett avstånd på 100 mm kan
skada ögonen.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
4-11
Chapter 4
Preparing to Install a Modular Services Card or a Shared Port Adapter
Safety Guidelines
Statement 1071—Warning Definition
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this
device. Statement 1071
SAVE THESE INSTRUCTIONS
Waarschuwing
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan
veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij
elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard
praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de
waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt
raadplegen.
BEWAAR DEZE INSTRUCTIES
Varoitus
TÄRKEITÄ TURVALLISUUSOHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin
käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu
onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen
mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien
lausuntonumeroiden avulla.
SÄILYTÄ NÄMÄ OHJEET
Attention
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant
entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez
conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures
couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des
avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen
kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und
den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder
Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
4-12
OL-4681-01
Chapter 4
Preparing to Install a Modular Services Card or a Shared Port Adapter
Safety Guidelines
Avvertenza
IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle
persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli
relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.
Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le
traduzioni delle avvertenze riportate in questo documento.
CONSERVARE QUESTE ISTRUZIONI
Advarsel
VIKTIGE SIKKERHETSINSTRUKSJONER
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du
begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med
elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten
av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne
enheten.
TA VARE PÅ DISSE INSTRUKSJONENE
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de
lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos
perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de
prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para
localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.
GUARDE ESTAS INSTRUÇÕES
¡Advertencia!
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular
cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los
procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el
número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña
a este dispositivo.
GUARDE ESTAS INSTRUCCIONES
Varning!
VIKTIGA SÄKERHETSANVISNINGAR
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.
Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och
känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av
varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna
anordning.
SPARA DESSA ANVISNINGAR
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
4-13
Chapter 4
Preparing to Install a Modular Services Card or a Shared Port Adapter
Safety Guidelines
Electrical Equipment Guidelines
Follow these basic guidelines when working with any electrical equipment:
•
Before beginning any procedures requiring access to the chassis interior, locate the emergency
power-off switch for the room in which you are working.
•
Disconnect all power and external cables before moving a chassis.
•
Do not work alone when potentially hazardous conditions exist.
•
Never assume that power has been disconnected from a circuit; always check.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
4-14
OL-4681-01
Chapter 4
Preparing to Install a Modular Services Card or a Shared Port Adapter
Safety Guidelines
•
Do not perform any action that creates a potential hazard to people or makes the equipment unsafe;
carefully examine your work area for possible hazards such as moist floors, ungrounded power
extension cables, and missing safety grounds.
Telephone Wiring Guidelines
Use the following guidelines when working with any equipment that is connected to telephone wiring or
to other network cabling:
•
Never install telephone wiring during a lightning storm.
•
Never install telephone jacks in wet locations unless the jack is specifically designed for wet
locations.
•
Never touch uninsulated telephone wires or terminals unless the telephone line has been
disconnected at the network interface.
•
Use caution when installing or modifying telephone lines.
Preventing Electrostatic Discharge Damage
Electrostatic discharge (ESD) damage, which can occur when electronic cards or components are
improperly handled, results in complete or intermittent failures. MSCs, SPAs, and processor modules
comprise printed circuit boards that are fixed in metal carriers. Electromagnetic interference (EMI)
shielding and connectors are integral components of the carrier. Although the metal carrier helps to
protect the board from ESD, use a preventive antistatic strap during handling.
Following are guidelines for preventing ESD damage:
Note
•
Always use an ESD wrist or ankle strap and ensure that it makes good skin contact.
•
Connect the equipment end of the strap to an unfinished chassis surface.
•
When installing a component, use any available ejector levers or captive installation screws to
properly seat the bus connectors in the backplane or midplane. These devices prevent accidental
removal, provide proper grounding for the system, and help to ensure that bus connectors are
properly seated.
•
When removing a component, use any available ejector levers or captive installation screws to
release the bus connectors from the backplane or midplane.
•
Handle carriers by available handles or edges only; avoid touching the printed circuit boards or
connectors.
•
Place a removed board component-side-up on an antistatic surface or in a static shielding container.
If you plan to return the component to the factory, immediately place it in a static shielding
container.
•
Avoid contact between the printed circuit boards and clothing. The wrist strap only protects
components from ESD voltages on the body; ESD voltages on clothing can still cause damage.
•
Never attempt to remove the printed circuit board from the metal carrier.
For safety, periodically check the resistance value of the antistatic strap. The measurement should be
between 1 and 10 megohms (Mohms).
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
4-15
Chapter 4
Preparing to Install a Modular Services Card or a Shared Port Adapter
Laser/LED Safety
Laser/LED Safety
An optical single-mode transmitter uses a small laser to transmit the light signal to the network ring.
Keep the transmit port covered whenever a cable is not connected to it. Although multimode transceivers
typically use LEDs for transmission, it is good practice to keep open ports covered and avoid staring into
open ports or apertures. The single-mode aperture port contains a laser warning label, as shown in
Figure 4-1. The multimode aperture contains a Class 1 LED warning label, as shown in Figure 4-2.
These warnings apply to SPAs and SFP modules that transmit signals via an optical carrier signal.
Figure 4-1
Laser Warning Labels for Single-Mode Port
PRODUIT LASER DE CLASSE 1
1
PRODUCTO LASER CLASE 1
H6655
CLASS 1 LASER PRODUCT
LASERPRODUKT DER KLASSE 1
Warning
Class 1 laser product. Statement 1008
Warning
Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into
beams or view directly with optical instruments. Statement 1051
Waarschuwing
Losgekoppelde of losgeraakte glasvezels of aansluitingen kunnen onzichtbare laserstraling
produceren. Kijk niet rechtstreeks in de straling en gebruik geen optische instrumenten rond deze
glasvezels of aansluitingen.
Varoitus
Irrotetuista kuiduista tai liittimistä voi tulla näkymätöntä lasersäteilyä. Älä tuijota säteitä tai katso
niitä suoraan optisilla välineillä.
Attention
Les fibres ou connecteurs débranchés risquent d'émettre des rayonnements laser invisibles à l'œil.
Ne regardez jamais directement les faisceaux laser à l'œil nu, ni d'ailleurs avec des instruments
optiques.
Warnung
Unterbrochene Fasern oder Steckerverbindungenkönnen unsichtbare Laserstrahlung abgeben.
Blicken Sie weder mit bloßem Auge noch mit optischen Instrumenten direkt in Laserstrahlen.
Avvertenza
Le fibre ottiche ed i relativi connettori possono emettere radiazioni laser. I fasci di luce non devono
mai essere osservati direttamente o attraverso strumenti ottici.
Advarsel
Det kan forekomme usynlig laserstråling fra fiber eller kontakter som er frakoblet. Stirr ikke direkte
inn i strålene eller se på dem direkte gjennom et optisk instrument.
Aviso
¡Advertencia!
Radiação laser invisível pode ser emitida de conectores ou fibras desconectadas. Não olhe
diretamente para os feixes ou com instrumentos ópticos.
Es posible que las fibras desconectadas emitan radiación láser invisible. No fije la vista en los
rayos ni examine éstos con instrumentos ópticos.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
4-16
OL-4681-01
Chapter 4
Preparing to Install a Modular Services Card or a Shared Port Adapter
Laser/LED Safety
Varning!
Aviso
Advarsel
Osynlig laserstrålning kan avges från frånkopplade fibrer eller kontaktdon. Rikta inte blicken in i
strålar och titta aldrig direkt på dem med hjälp av optiska instrument.
Radiação laser invisível pode ser emitida a partir de fibras ou conectores desconectados. Não fixe
o olhar nos feixes e nem olhe diretamente com instrumentos ópticos.
Usynlig laserstråling kan forekomme fra brugte fibre eller stik. Stir ikke ind i stråler eller direkte
med optiske instrumenter.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
4-17
Chapter 4
Preparing to Install a Modular Services Card or a Shared Port Adapter
Laser/LED Safety
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
4-18
OL-4681-01
Chapter 4
Preparing to Install a Modular Services Card or a Shared Port Adapter
The multimode aperture contains a Class 1 LED warning label, as shown in Figure 4-2.
Class 1 LED Warning Label for Multimode Port
CLASS 1 LED PRODUCT
PRODUKT MIT KLASSE 1 LED
PRODUIT AVEC VOYANT DEL
DE CLASSE 1
LED
PRODUCTO LED DE LA CLASE 1
11773
Figure 4-2
Warning
Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into
beams or view directly with optical instruments. Statement 1051
Warning
Class 1 LED product Statement 1027
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
4-19
Chapter 4
Preparing to Install a Modular Services Card or a Shared Port Adapter
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
4-20
OL-4681-01
C H A P T E R
5
Installing and Removing a Carrier Card
This chapter describes how to install or remove carrier cards on the Cisco 7304 router. This chapter
contains the following sections:
•
Handling MSCs, page 5-1
•
Online Insertion and Removal, page 5-2
•
MSC Installation and Removal, page 5-3
Handling MSCs
Each MSC circuit board is mounted to a metal carrier and is sensitive to electrostatic discharge (ESD)
damage. Before you begin installation, read Chapter 4, “Preparing to Install a Modular Services Card or
a Shared Port Adapter,” for a list of parts and tools required for installation.
When a slot is not in use, a blank module filler plate must fill the empty slot to allow the router or switch
to conform to electromagnetic interference (EMI) emissions requirements and to allow proper airflow
across the installed modules. If you plan to install an MSC in a slot that is not in use, you must first
remove the blank module filler plate.
Caution
Always handle the MSC by the carrier edges and handle; never touch the MSC components or connector
pins. (See Figure 5-1.)
Caution
When powering off the router, wait a minimum of 30 seconds before powering it on again.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
5-1
Chapter 5
Installing and Removing a Carrier Card
Online Insertion and Removal
Figure 5-1
Handling an MSC
70006
Printed circuit board
Metal carrier
GND
Online Insertion and Removal
OIR allows you to install and replace MSCs while the router is operating; you do not need to notify the
software or shut down the system power, although you should not run traffic through the module you are
removing while it is being removed. OIR is a method that is seamless to end users on the network,
maintains all routing information, and preserves sessions.
The Cisco 7304 router supports OIR of the MSC. To do this, you can stop an MSC (which automatically
deactivates any installed SPAs) and remove the MSC with the SPAs still intact.
If you plan to remove an MSC, we recommend that you deactivate the MSC first using the hw-module
slot privileged EXEC command. When you deactivate an MSC using this command, it automatically
deactivates each of the SPAs that are installed in that MSC and allows for the completion of data traffic
before the active interfaces are shut down. Therefore, it is not necessary to deactivate each of the SPAs
prior to deactivating the MSC.
Although graceful deactivation of an MSC is preferred using the hw-module slot stop command, the
Cisco 7304 router does not support removal of the MSC without deactivating it first.
Note
CLI-controlled OIR using the hw-module slot stop command is the recommended way of performing
OIR on this platform.
Note
As you disengage the MSC from the router, online insertion and removal (OIR) administratively shuts
down all active interfaces on the MSC.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
5-2
OL-4681-01
Chapter 5
Installing and Removing a Carrier Card
MSC Installation and Removal
MSC Installation and Removal
This section provides step-by-step instructions for installing and removing an MSC.
Caution
Insert or remove only one MSC at a time. Inserting or removing more than one MSC at a time can cause
the system to detect spurious hardware failures.
Warning
When performing the following procedures, wear a grounding wrist strap to avoid ESD damage to the
MSC. Some platforms have an ESD connector for attaching the wrist strap. Do not directly touch the
midplane or backplane with your hand or any metal tool, or you could shock yourself.
To install and remove an MSC, refer to Figure 5-2 and Figure 5-3 and do the following:
Step 1
To insert the MSC, carefully align the edges of the MSC between the upper and lower edges of the
module slot, as shown in A of Figure 5-2.
Step 2
Ensuring that the MSC is properly aligned in the router slot, carefully slide the MSC into the module
slot until the MSC makes contact with the backplane.
Note
Step 3
The MSC ejector levers must be positioned at a 45-degree angle before the MSC makes contact
with the backplane.
Push the MSC ejector levers in until the MSC is fully seated in the router backplane.
Note
Caution
When the router chassis is fully populated, seating an MSC can be difficult. To properly seat the
MSC and avoid physical damage, loosen the locking captive installation screws on the
neighboring MSCs or line cards.
Use of excessive force can damage the router or MSC.
Step 4
Tighten the locking captive installation screws on both sides of the MSC, using a screwdriver. The MSC
is now installed in the router module slot.
Step 5
To remove the MSC, loosen the locking captive installation screws using a screwdriver on both sides of
the MSC, as shown in A of Figure 5-3.
Step 6
Pull out the MSC ejector levers, as shown in B of Figure 5-3, and carefully slide the MSC out of the
module slot. If you are removing a blank module filler plate, pull the blank module filler plate
completely out of the module slot.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
5-3
Chapter 5
Installing and Removing a Carrier Card
MSC Installation and Removal
Figure 5-2 illustrates how to install an MSC into a Cisco 7304 router. Figure 5-3 illustrates how to
remove an MSC from a Cisco 7304 router.
Figure 5-2
MSC Installation
A
XXX XXX
X
OIR
STATUS
7300 PA
CARRIER
XXX XXX
B
X
OIR
STATUS
7300 PA
C
CARRIER
XXX
XXX XXX
X
OIR
STATUS
7300 PA
CARRIER
98433
OIR
STATUS
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
5-4
OL-4681-01
Chapter 5
Installing and Removing a Carrier Card
MSC Installation and Removal
Figure 5-3
MSC Removal
XXX
A
XXX XXX
X
OIR
STATUS
7300 PA
CARRIER
OIR
STATUS
1
SLOT 2
CATALYST 2986
98433
47
2
1
2
3
4
5
6
7
8
9
10
11
1
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
48
32
33
34
31
35
36
37
38
39
40
41
42
43
44
45
46
47
48
CONSOLE
STATUS
10/100/1000 ETHERENET
2
1
2
3
4
5
10MB MGT
RESET
6
7
8
9
10
11
12
13
14
15
16
17
18
19
32
20
21
22
23
24
25
SLOT 3
26
27
28
29
30
31
33
32
34
XXX XXX
B
PWR
X
OIR
STATUS
7300 PA
CARRIER
C
XXX XXX
X
OIR
STATUS
CARRIER
98434
7300 PA
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
5-5
Chapter 5
Installing and Removing a Carrier Card
MSC Installation and Removal
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
5-6
OL-4681-01
C H A P T E R
6
Installing and Removing a Shared Port Adapter
This chapter describes how to install or remove SPAs on the Cisco 7304 router. This chapter contains the
following sections:
•
Handling SPAs, page 6-1
•
Online Insertion and Removal, page 6-2
•
SPA Installation and Removal, page 6-2
•
Optical Device Installation and Removal (SPA-2GE-7304 optional procedure), page 6-4
•
Checking the Installation, page 6-4
•
SPA Cable Management Brackets, page 6-9
Handling SPAs
Each SPA circuit board is mounted to a metal carrier and is sensitive to electrostatic discharge (ESD)
damage. Before you begin installation, read Chapter 4, “Preparing to Install a Carrier Card or a Shared
Port Adapter,” for a list of parts and tools required for installation.
Caution
Always handle the SPA by the carrier edges and handle; never touch the SPA components or connector
pins. (See Figure 6-1.)
When a slot is not in use, a blank filler plate must fill the empty slot to allow the router or switch to
conform to electromagnetic interference (EMI) emissions requirements and to allow proper airflow
across the installed modules. If you plan to install a SPA in a slot that is not in use, you must first remove
the blank filler plate.
Figure 6-1
Handling a SPA
Metal carrier
H6420
Printed circuit board
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
6-1
Chapter 6
Installing and Removing a Shared Port Adapter
Online Insertion and Removal
Online Insertion and Removal
The Cisco 7304 router supports OIR of a SPA independently of removing the MSC. This means that an
MSC can remain installed in the router with one SPA remaining active while you remove another SPA
from one of the MSC subslots. If you are not planning to immediately replace a SPA into the MSC, then
be sure to install a SPA blank filler plate in the subslot. The MSC can be inserted and removed using
OIR without removing the SPAs in the installed subslots and the MSCs should always be fully installed
with either functional SPAs or SPA blank filler plates.
For additional information regarding OIR of a SPA in an MSC, see the Cisco 7304 Router Modular
Services Card and Shared Port Adapter Software Configuration Guide.
SPA Installation and Removal
You can install two half-height SPAs in an MSC-100. This section provides step-by-step instructions for
removing and installing a SPA in an MSC.
Warning
When performing the following procedures, wear a grounding wrist strap to avoid ESD damage to the
SPA. Some platforms have an ESD connector for attaching the wrist strap. Do not directly touch the
midplane or backplane with your hand or any metal tool, or you could shock yourself.
To remove and install a SPA in an MSC, refer to Figure 6-2 and Figure 6-3 and do the following:
Note
Caution
The MSC can be inside or outside the router slot when the SPA is being installed or removed.
Remove all cables from the SPAs prior to installation. Do not install cables into the SPAs until the SPA
is properly seated in the MSC and the locking captive installation screws on the SPA are in their locked
positions.
Step 1
Remove all cabling from the SPA if any cabling has been connected to the SPA.
Step 2
Remove the SPA from the MSC. To remove the SPA from the MSC, unlock the SPA locking captive
installation screws from their locked positions using a screwdriver as shown in 1 of Figure 6-2 to the
unlocked positions.
Step 3
Grasp the handle of the SPA and pull the SPA from the MSC.
Step 4
To insert the SPA in the MSC, locate the guide rails inside the MSC that hold the SPA in place. They are
at the top left and top right of the SPA slot and are recessed about an inch, as shown in 1 of Figure 6-3.
Step 5
Carefully slide the SPA all the way into the MSC until the SPA is firmly seated in the SPA interface
connector. When fully seated, the SPA might be slightly behind the MSC faceplate.
Step 6
After the SPA is properly seated, use a screwdriver to turn the SPA locking captive installation screws
to their locked positions, as shown in 2 of Figure 6-3.
Figure 6-2 illustrates how to remove a SPA from an MSC and Figure 6-3 illustrates how to install a SPA
into an MSC.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
6-2
OL-4681-01
Chapter 6
Installing and Removing a Shared Port Adapter
SPA Installation and Removal
Figure 6-2
X
98436
XX XX XX
SPA Removal
OIR
STATUS
7300 PA
ATM
CARRIE
R
1
2
Figure 6-3
1
SPA Installation
XXXXX
X
1
X
98435
XXX XXX
OIR
STATUS
7300 PA
CARRIER
ATM
2
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
6-3
Chapter 6
Installing and Removing a Shared Port Adapter
Optical Device Installation and Removal (SPA-2GE-7304 optional procedure)
Optical Device Installation and Removal (SPA-2GE-7304
optional procedure)
This section provides references for the installation, removal, and cleaning of optical devices.
Installing and Removing Small Form-Factor Pluggable Modules
For information on installing small form-factor pluggable (SFP) modules, see Gigabit Interface
Converter (GBIC) Module and Small Form-Factor Pluggable (SFP) GBIC Module Installation
Information and Specifications. The following sections of that document are particularly useful when
installing an SFP module:
•
“Installing and Removing the GBIC Module or SFP Module”
•
“Installing an SFP Module”
•
“Installing the GBIC Module or SFP Module Interface Cables”
SPAs accept only supported optical devices. The list of supported optical devices can be found in the
Modular Optics Compatibility table in the product overview chapter of this guide.
Cleaning Optical Devices
Any contamination of the fiber connection can cause failure of the component or failure of the whole
system. A particle that partially or completely blocks the core generates strong back reflections, which
can cause instability in the laser system. Inspection, cleaning, and reinspection are critical steps to take
before making fiber-optic connections.
For information on cleaning optical devices, refer to Inspection and Cleaning Procedures for
Fiber-Optic Connections.
Checking the Installation
This section describes the procedures you can use to verify the MSC and SPA installation, and includes
information on the following topics:
•
Verifying the Installation, page 6-4
•
Using show Commands to Verify MSC and SPA Status, page 6-6
•
Using show Commands to Display SPA Information, page 6-7
•
Using the ping Command to Verify Network Connectivity, page 6-8
Verifying the Installation
This section describes how to verify the MSC and SPA installation by observing the MSC LED states,
SPA LED states, and the information displayed on the console terminal.
When the system has reinitialized all interfaces, the MSC STATUS LED should be green (on) and the
port LEDs on the SPAs should be green (on), depending on your connections and configuration. The
console screen also displays a message as the system discovers each interface during its reinitialization.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
6-4
OL-4681-01
Chapter 6
Installing and Removing a Shared Port Adapter
Checking the Installation
Note
A Fast Ethernet interface is used in the following examples for illustrative purposes.
The following sample display shows the events logged by the system as an MSC with a Fast Ethernet
SPA was removed from module slot 4 in the router. In this example, interface 0 (interface 4/0/0) on the
FastEthernet SPA was up and active when the MSC was removed from the router. Note that the system
logs that the MSC card was removed from slot 4 and that interface 4/0/0 is changed to down.
Router#
00:06:17:%WS_ALARM-6-INFO:ASSERT CRITICAL slot 4 Active Card Removed OIR Alarm
00:06:17:%OIR-6-REMCARD:Card removed from slot 4, interfaces disabled
00:06:18:%LINEPROTO-5-UPDOWN:Line protocol on Interface FastEthernet4/0/0, changed state
to down
When you reinsert the MSC with the installed SPA, the system automatically brings up the interface that
was changed to down when the MSC was removed.
Router#
00:07:29:%OIR-6-INSCARD:Card inserted in slot 4, interfaces administratively shut down
00:07:32:%WS_ALARM-6-INFO:CLEAR CRITICAL slot 4 Active Card Removed OIR Alarm
00:07:35:%LINK-3-UPDOWN:Interface FastEthernet4/0/0, changed state to up
00:07:36:%LINEPROTO-5-UPDOWN:Line protocol on Interface FastEthernet4/0/0, changed state
to up
Use the following procedure to verify that the MSC is installed correctly:
Step 1
Observe the console display messages and verify that the system discovers the MSC, while the system
reinitializes each interface, as follows:
•
If you installed a new MSC, the STATUS LED should be green (on). The system should recognize
all new interfaces but leave them configured as administratively down.
•
If you replaced an MSC, the STATUS LED should be green (on). The system should recognize each
interface and places each interface in the state that it was previously in before the MSC was
removed.
Step 2
Verify that the STATUS LED on the SPA goes on (is green) and remains on after the reinitialization is
complete. If the STATUS LED remains on, proceed to Step 5. If the STATUS LED does not remain on,
proceed to Step 3.
Step 3
If the STATUS LED on the SPA fails to go on, the SPA or the MSC might not have a compatible FPD
image or the SPA or MSC might not be fully seated even if the SPA locking captive installation screws
are locked. When a SPA is not recognized, the SPA STATUS LED is off. If this occurs in your network,
do the following:
a.
Check for system messages indicating an FPD incompatibility or enter the show hw-module
subslot fpd command to ensure the FPD image on the SPA is compatible with the running Cisco
IOS. If an incompatibility exists, an FPD image package file must be downloaded from the Software
Center on Cisco.com and an FPD upgrade must be performed. For information on performing this
upgrade, see the “Upgrading Field-Programmable Devices” chapter of the Cisco 7304 Modular
Services Card and Shared Port Adapter Software Configuration Guide. If the FPD is proven to be
compatible or you are unable to perform the verification steps, proceed with the following steps:
b.
Remove the SPA from the MSC.
c.
Inspect the SPA. Verify there are no bent pins or parts and that there is nothing lodged in the two
devices that could prevent a good connection.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
6-5
Chapter 6
Installing and Removing a Shared Port Adapter
Checking the Installation
Step 4
d.
Insert the SPA in the MSC by sliding the SPA all the way in the MSC until the SPA is firmly seated
in the SPA interface connector. When fully seated in the MSC, the SPA might be slightly behind the
MSC faceplate.
e.
After the system reinitialization, the STATUS LED on the SPA should go on and remain on. If the
STATUS LED remains on, proceed to Step 5. If it does not, proceed to Step 4.
If the STATUS LED on a SPA still fails to go on and the problem is not FPD-related, remove the MSC
and install it in another available slot on the router.
•
If the STATUS LED on the SPA goes on, suspect a failed backplane port in the original slot.
•
If the STATUS LED fails to go on, remove the MSC and ensure the SPA is firmly seated in its slot.
Remove and reinstall it accordingly.
•
If the STATUS LED still fails to go on, but other LEDs on the SPA go on to indicate activity, proceed
to Step 5 to resume the installation check; suspect that the STATUS LED on the SPA has failed.
Contact a service representative to report the problem and obtain further instructions.
•
If no LEDs on the SPA go on:
– Verify that the SPA is supported on the MSC and that it has the required hardware revision. If
the SPA is not supported or has an old hardware revision, the show diag command output will
verify that the MSC is deactivated.
– Suspect a faulty MSC. Contact a service representative to report the problem and obtain further
instructions.
Step 5
If the SPA is new and not a replacement, configure the new SPA using the Cisco 7304 Modular Services
Card and Shared Port Adapter Software Configuration Guide.
Step 6
If the MSC is a replacement, use the show interfaces type slot-number/port-number/SPA-port-number
command or the show controllers command to verify the status of the SPAs. (See the “Using show
Commands to Verify MSC and SPA Status” section on page 6-6.)
If you replaced an MSC with another MSC with a different SPA installed, the system recognizes the
interfaces on the previously configured SPA but does not recognize the new SPA interfaces. The new
interfaces remain in the shutdown state until you configure them.
Step 7
When the interfaces are up, check the activity of each SPA by observing the STATUS LEDs.
Step 8
If the port LED (a port LED is one of the numbered LEDs) on the SPA fails to go on and a cable is
connected to the interface port, check the cable connection and make certain it is properly seated in the
connector.
Step 9
Repeat Step 1 through Step 8 to verify that any additional MSCs are properly installed.
If you experience other problems that you are unable to solve, contact Cisco Technical Support (see the
“Obtaining Technical Assistance” section on page -xi) or a service representative for assistance.
To configure the new interface, use the Cisco 7304 Modular Services Card and Shared Port Adapter
Software Configuration Guide.
Using show Commands to Verify MSC and SPA Status
The following steps use show commands to verify that the new SPAs are configured and operating
correctly:
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
6-6
OL-4681-01
Chapter 6
Installing and Removing a Shared Port Adapter
Checking the Installation
Step 1
Use the show c7300 command to display the list of supported hardware in each router slot, including
supported SPAs, SPA type, and SPA status. Ensure that your SPA is listed in the output and that the status
is OK.
Step 2
Use the show version command to display the system hardware configuration. Ensure that the list
includes the new SPAs and the correct interface types.
Step 3
Specify one of the new SPAs with the show interfaces type router-module-slot/subslot/SPA-port-number
command and verify that the first line of the display specifies the SPA with the correct slot number. Also
verify that the SPA and line protocol are in the correct state: up or down.
Step 4
Display the protocols configured for the entire system and specific SPAs with the show protocols
command. If necessary, return to configuration mode to add or remove protocol routing on the system
or specific SPAs.
Step 5
Display the running configuration file with the show running-config command. Verify that the
configuration is accurate for the system and each SPA.
Step 6
Display the SPA FPD image version and the required image version using the show hw-module subslot
fpd command. An FPD incompatibility can disable a SPA, so this command is useful for verifying that
the FPD image on the SPA is compatible with the running Cisco IOS release.
If the SPA is down and you configured it as up, or if the displays indicate that the hardware is not
functioning properly, ensure that the network interface is properly connected. If you still have problems
bringing the SPA up, contact a service representative for assistance.
Using show Commands to Display SPA Information
Table 6-1 describes the show commands you can use to display SPA information.
Table 6-1
show Commands to Display SPA Information
Command
Type of Information Provided
show running-config
The router’s running configuration and interfaces available in the
system.
show hw-module subslot oir
The operational status of all SPAs in the system.
show controllers
General hardware information about a particular SPA, MSC, or all
hardware in the system.
show diag
SPA type in that slot, number of ports, hardware revision, part
number, FPGA, and EEPROM contents.
show hw-module subslot fpd
FPD version information of SPAs in the system.
show version
Cisco IOS software version, names and sources of configuration
files, and boot images.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
6-7
Chapter 6
Installing and Removing a Shared Port Adapter
Checking the Installation
Using the ping Command to Verify Network Connectivity
This section provides brief descriptions of the ping command. The ping command allows you to verify
that a SPA port is functioning properly and to check the path between a specific port and connected
devices at various locations on the network. After you verify that the system and the MSC have booted
successfully and are operational, you can use this command to verify the status of the SPA ports. Refer
to the publications listed in the “Related Documentation” section on page -viii for detailed command
descriptions and examples.
The ping command sends an echo request out to a remote device at an IP address that you specify. After
sending a series of signals, the command waits a specified time for the remote device to echo the signals.
Each returned signal is displayed as an exclamation point (!) on the console terminal; each signal that is
not returned before the specified timeout is displayed as a period (.). A series of exclamation points
(!!!!!) indicates a good connection; a series of periods (.....) or the messages [timed out] or [failed]
indicate that the connection failed.
Following is an example of a successful ping command to a remote server with the IP address 10.1.1.60:
Router# ping 10.1.1.60 <Return>
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echoes to 10.1.1.60, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/15/64 ms
Router#
If the connection fails, verify that you have the correct IP address for the server and that the server is
active (powered on), and repeat the ping command.
SPAs are shipped with an accessory kit that includes cable management brackets. Figure 6-4 shows
cable management brackets installed in a SPA, as well as cable routing.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
6-8
OL-4681-01
Chapter 6
Installing and Removing a Shared Port Adapter
SPA Cable Management Brackets
SPA Cable Management Brackets
Figure 6-4
SPA Cable Management Brackets
FAN
STATUS
WS-X6K-SUP2-2GE
US
1
AT
ST
T
LE
EM
ST
SY
M
G
O
NS
CO
R
M
PW
T
SE
RE
Switch
100%
CONSOLE
PORT
MODE
CONSOLE
SUPERVISOR2
Load
PORT 1
PCMCIA
PORT 2
EJECT
1%
OSM-4OC12 POS-SI
NK
LI
1
E
TIV
RX
AC
4 PORT OC-12 POS SM
7600-MSC-600
0
NK
LI
3
TX
TX
US
AT
ST
2
T
SE
4
K
LIN
IR
C/A
RE
K
2 LIN
1
0
A/L C/A
0
K
LIN
A/L C/A
0
A/L C/A
K
4 LIN
3
0
E
TIV
R
IE M
RR AR
CA AL
RX
AC
TX
TX
RX
RT
E
TIV
R
IE M
RR AR
CA AL
TX
TX
RX
1
PO
RX
AC
RT
PO
2
E
TIV
TX
TX
RX
R
IE M
RR AR
CA AL
RX
AC
RT
PO
3
RX
R
IE M
RR AR
CA AL
4
RT
129582
2
PO
A/L
S
3
TU
STA
ST
US
AT
MODULAR
SERVICES CARD
S
1
TU
STA
2
SPA-4XOC3-ATM
3
Note
This illustration is from a Cisco 7600 router, but the cable management brackets are identical on a
Cisco 7304 router.
To install cable management brackets on a SPA, perform the following steps:
Step 1
Screw the two pull assemblies into both sides of the SPA.
Step 2
Insert the cable management clip into the slot.
Step 3
To remove the cable management clip, depress the button on the clip and pull it out.
Note
Blank filler plugs are provided if no cable management clips are installed.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
6-9
Chapter 6
Installing and Removing a Shared Port Adapter
SPA Cable Management Brackets
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
6-10
OL-4681-01
C H A P T E R
7
Troubleshooting the Installation
This chapter describes how to troubleshoot the installation of MSCs and SPAs on the Cisco 7304 router.
This chapter contains the following sections:
•
Troubleshooting, page 7-1
•
Error Messages, page 7-4
•
Other Troubleshooting Resources, page 7-4
•
Packing a SPA for Shipment, page 7-4
Troubleshooting
This section describes some general troubleshooting information for the MSCs and SPAs with an
emphasis on hardware troubleshooting. Possible problems, observations and comments, and solutions
are indicated for the following troubleshooting symptoms:
•
MSC transitions repeatedly from on to off
•
MSC is deactivated
•
SPA is down and the line protocol is down
MSC Transitions Repeatedly From On to Off
Possible Problem
Observations and Comments
Solutions
MSC is booting up; this is
normal operation
MSC STATUS LED alternates
from off to yellow to green
Wait 30 seconds until the boot process completes and the
STATUS LED stays on.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
7-1
Chapter 7
Troubleshooting the Installation
Troubleshooting
MSC Transitions Repeatedly From On to Off
Possible Problem
Observations and Comments
MSC does not go beyond the MSC STATUS LED transitions
bootup stage
continue and alternates green,
yellow, or off
Solutions
Look up the error message in the “Error Messages” section
on page 7-4. Follow the recommended action for the
displayed error message.
Error message on the 7304
console
%FPD-MGMT system messages
appear on the console indicating
the FPD is incompatible and
either the upgrade attempt failed
or no messages appear indicating
an FPD upgrade was attempted
Enter the show hw-module subslot fpd command to verify
if an FPD incompatibility exists. If an incompatibility
exists, an FPD image package file needs to be downloaded
from the Software Center on Cisco.com and an FPD
upgrade needs to be performed. For information on
performing this upgrade, see the “Upgrading
Field-Programmable Devices” section of the Cisco 7304
Router Modular Services Card and Shared Port Adapter
Software Configuration Guide.
Possible Problem
Observations and Comments
Solutions
No SPA is installed in the
MSC
Error message indicating no SPA If a SPA is not supposed to be installed in the router slot,
is detected
this is not a problem.
The SPA FPD Image is
incompatible with the
running Cisco IOS Release
MSC STATUS LED is green
SPA STATUS LED is off
MSC Is Deactivated
Output of the show diag slot
command
SPA STATUS LED is off
SPA is not fully seated in the Output of the show diag slot
MSC
command
MSC STATUS LED is green
MSC OIR LED is off
If you would like a SPA in the slot, install a SPA supported
on the MSC and ensure the SPA is properly seated in the
MSC.
Follow this procedure:
•
Remove the MSC from the router.
•
Remove the SPA from the MSC.
•
Inspect the MSC and the SPA. Verify there are no bent
pins or parts and that there is nothing lodged in the two
devices that could prevent a good connection.
•
Insert the SPA in the MSC by sliding the SPA all the
way in the MSC until the SPA is firmly seated in the
SPA interface connector. When fully seated in the MSC,
the SPA might be slightly behind the MSC faceplate.
•
Insert the MSC into the router.
SPA STATUS LED is off
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
7-2
OL-4681-01
Chapter 7
Troubleshooting the Installation
Troubleshooting
MSC Is Deactivated
Possible Problem
Observations and Comments
Solutions
SPA is not supported on the
MSC
Error message indicating the
SPA is not supported
Install a SPA supported on the MSC.
Output of the show diag slot
command
MSC STATUS LED is green
MSC OIR LED is off
SPA STATUS LED is off
SPA is not at the minimum
hardware revision level
Upgrade the SPA to the minimum hardware revision level
Error message indicating the
required.
SPA is not at the minimum
hardware revision level required
Output of the show diag slot
command
MSC STATUS LED is on
MSC OIR LED is off
SPA STATUS LED is off
SPA Is Down and the Line Protocol Is Down
Possible Problem
Observations and Comments
Solutions
SPA is not at the minimum
hardware revision level
Error message indicating the
SPA is not at the minimum
hardware revision level required
Upgrade the SPA to the minimum hardware revision
required.
Output of the show diag slot
command
MSC STATUS LED is on
MSC OIR LED is off
SPA STATUS LED is off
MSC FPGA is not up to date During MSC initialization, the
need to update the FPGA is
automatically detected
Follow the system prompts to update the FPGA image.
SPA is misconfigured
Refer to the configuration section of the specific SPA
installation and configuration guide, or use the Cisco IOS
software configuration documentation listed in the
“Related Documentation” section on page -viii.
Manually upgrade the FPGA using the upgrade fpga all
command.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
7-3
Chapter 7
Troubleshooting the Installation
Error Messages
SFP Issues for Gigabit Ethernet SPA
Possible Problem
Observations and Comments
Solutions
SFP is not recognized
A
%SPA_ETHER-3-SFP_SEC_FA
IL message appears on the
console
Ensure that the SFP you are using is supported by the
Gigabit Ethernet SPA. The list of supported SPAs can be
viewed in the “SFP Connections” section in Chapter 2 of
this document. The Gigabit Ethernet SPAs for the
Cisco 7304 router only support Cisco SFPs.
The interface line protocol as
shown in the show interfaces
command output is down
Error Messages
To view the explanations and recommended actions for Cisco 7304 error messages, including messages
related to Cisco 7304 MSCs and SPAs, see the following document:
•
System Error Messages for Cisco IOS Release 12.2 S (for error messages in Cisco IOS
Release 12.2 S)
Other Troubleshooting Resources
For additional troubleshooting documentation, see the following documents:
•
The“Troubleshooting” section of the Cisco 7304 Router Modular Services Cards and Shared Port
Adapter Software Configuration Guide
Packing a SPA for Shipment
This section provides step-by-step instructions for packing a Cisco 7304 MSC-100 for shipment. Before
beginning this procedure, you should have the following original Cisco Systems packaging materials:
•
Static shielding bag
•
Two foam pads
•
Rectangular-shaped foam collar
•
Carton
In addition to the above materials, you will also need carton-sealing tape.
Caution
The Cisco Systems original packaging is to be used for the shipment of all MSCs. Failure to properly
use Cisco Systems packaging can result in damage or loss of product.
Warning
During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly
touch the backplane with your hand or any metal tool, or you could shock yourself.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
7-4
OL-4681-01
Chapter 7
Troubleshooting the Installation
Packing a SPA for Shipment
Note
These instructions assume that the Cisco 7304 MSC-100 has been removed from the router according to
the recommended procedures specified in this guide.
To pack a Cisco 7304 MSC-100 for shipment, perform the following steps:
Step 1
Insert the Cisco 7304 MSC-100 into the static shielding bag.
Step 2
Insert the bagged Cisco 7304 MSC-100 between the foam pads and inside the rectangular-shaped foam
collar.
Step 3
Place the assembled packing components into the carton and tape the lower front edge of the carton
closed.
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
OL-4681-01
7-5
Chapter 7
Troubleshooting the Installation
Packing a SPA for Shipment
Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide
7-6
OL-4681-01