Avalon Stoves Arbor Owner`s manual

Arbor™
Pellet Stove
•
Horizontal
Or Vertical Vent
•
Freestanding Stove
•
Mobile Home Approved
•
Class A Chimney Retrofit
•
Hearth Stove into Existing
Masonry Chimney , Masonry
Fireplace, or Z.C. Fireplace
Tested and Listed by
Omni-Test Laboratories, Inc.
Portland, Oregon
Report # 028-S-77-2
ASTM E1509-2004
- - Please read this entire manual before installation and use of this pellet fuelburning room heater. Failure to follow these instructions could result in property
damage, bodily injury, or even death.
- - Contact local building or fire officials about restrictions and installation inspection
requirements in your area.
- - Save these instructions.
Installer: After installation give this manual to the home-owner and
explain operation of this stove.
$10.00
 Copyright 2008, T.I.
4080724
Part # 100-01191_000
4800 Harbour Pointe Blvd. SW
Mukilteo, WA 98275
Introduction
2
Introduction
We welcome you as a new owner of an Arbor pellet heater. In purchasing an Arbor you have joined
the growing ranks of concerned individuals whose selection of an energy system reflects both a
concern for the environment and aesthetics. The Arbor is one of the finest home heaters the world
over. This manual will explain the installation, operation, and maintenance of this pellet-burning
heater. Please familiarize yourself with the Owner's Manual before operating your heater and save the
manual for future reference. Included are helpful hints and suggestions which will make the
installation and operation of your new heater an easier and more enjoyable experience. We offer our
continual support and guidance to help you achieve the maximum benefit and enjoyment from your
heater.
Important Information
No other Arbor heater has the same serial number as
yours. The serial number is on the safety label on the
back of the appliance.
This serial number will be needed in case you require
service of any type.
Model:
Arbor PS
Serial Number:
Purchase Date:
To receive full warranty coverage,
you will need to show evidence of
the date you purchased your
heater. Do not mail your Bill of
Sale to us.
We suggest that you attach your
Bill of Sale to this page so that you
will have all the information you
need in one place should the need
for service or information occur.
Purchased From:
© Travis Industries
Mail your Warranty Card
Today, and Save Your Bill of
Sale.
4070806
100-01191_000
Table of Contents
Introduction
Operation (continued)
Introduction ......................................................2
Important Information .........................................2
Safety Precautions
Safety Precautions ............................................4
Specifications
Heating Specifications ........................................6
Dimensions.......................................................6
Electrical Specifications......................................6
Fuel.................................................................6
EPA Compliance ................................................6
Installation
Manual Mode.....................................................22
Auto Mode ........................................................23
Restrictor Adjustment .........................................24
Restrictor Adjustment .........................................24
Adjusting the Fan Speed......................................24
Start-Up Sequence.............................................25
"AUGER ON" Light..............................................25
"Maintenance Required" Light ...............................25
"MANUAL AUGER" Button....................................26
Power Outages..................................................26
Using a Pellet/Corn Mix with This Heater .................26
Maintenance
Before You Begin ...............................................7
Packing List......................................................7
Installation Options ............................................7
Planning The Installation .....................................7
Stove Placement ...............................................7
Floor Protection Requirements..............................7
Clearances - Straight Installation ..........................8
Clearances - Corner Installation ............................8
Venting the Pellet Stove ......................................9
Maximum Venting Distance .............................9
Pellet Vent Type............................................10
Installing the Pellet Vent .................................10
Pellet Vent Termination...................................10
Mobile Home Requirements ..................................11
Outside Air (used for combustion) .........................11
Alcove Installation Requirements ..........................12
Baffle Installation...............................................12
Door Seal Verification .........................................12
Restrictor Adjustment .........................................12
Thermostat Installation .......................................13
Installation Example: Direct "Through-the-wall"
Installation .......................................................14
Installation Example: Interior Vertical Installation ....15
Installation Example: Class A Chimney Retrofit ........16
InstallationExample: Masonry FireplaceHearthStove.......................17
InstallationExample: Zero-Clearance(Metal)FireplaceHearthStove..18
InstallationExample: FreestandingMasonry Chimney................19
Daily Maintenance (whenever using the stove).........27
Inspect the Burn ...........................................27
Make Sure Pellets are Not Piling Up...................27
Check Firepot for Clinkers ...............................28
Cleaning the Firepot .......................................28
Door Opening ...............................................29
Weekly Maintenance (or every 5 bags of pellets) ......30
Flyash Removal ............................................30
Clean the Hopper...........................................30
Clean the Heat Exchange Tubes.......................30
Clean the Baffles...........................................31
Sweep Ash Into Ashpan..................................32
Check Ashpan, Dispose if necessary ................33
Clean the Glass ............................................33
Yearly Maintenance (or every ton) .........................34
Clean the Vertical Exhaust Duct .......................34
Clean the Exhaust Blower ...............................36
Clean the Convection Blower ...........................37
Clean the Vent ..............................................37
Adjusting the Door Hinge and Latch...................37
Check for Air Leaks Around the Door, Glass, and
Ashpan .......................................................37
Replacement Parts ........................................38
Normal Operating Sounds
Normal Operating Sounds ....................................39
Safety Label
Safety Label .....................................................40
Operation
Safety Notice ....................................................20
Location of Controls ...........................................20
Starting the Heater for the First Time ......................20
Loading Pellets..................................................21
The Two Modes of Operation ................................21
© Travis Industries
3
4070806
Warranty
Warranty ..........................................................41
Index
Index...............................................................42
100-01191_000
Safety Precautions
4
• Do not operate the
heater if you smell
smoke coming from
the heater. Turn the
M ODE switch to
"OFF", monitor your
heater, and call your
dealer.
Gas
• Contact your local building
officials to obtain a permit
and information on any
installation restrictions or
inspection requirements
in your area. Notify your
insurance company of this
heater as well.
Ok
• Never use gasoline,
gasoline-type lantern fuel,
kerosene, charcoal lighter
fluid, or similar liquids to
start or 'freshen up' a fire in
this heater. Keep all such
liquids well away from the
heater while it is in use.
a
Se
lan
t
• The exhaust system must
be completely airtight and
properly installed. The
pellet vent joints must be
sealed with RTV 500o F.
(260o C.) silicone sealant.
• Do not unplug the heater
if you suspect a
malfunction. Turn the
MODE SWITCH to "OFF"
and periodically inspect
the heater.
• This unit must be properly
installed to prevent the
possibility of a house fire.
The instructions must be
strictly adhered to. Do not
use makeshift methods or
compromise in the
installation.
• Never try to repair or
replace any part of the
heater unless instructions
are given in this manual.
All other work should be
done by a trained
technician.
• Your heater requires
periodic maintenance and
cleaning (see "Maintaining
Your Heater"). Failure to
maintain your heater may
lead to smoke spillage in
your home.
• The viewing door and
ashpan must be closed
and latched during
operation.
• Never block free airflow
through the open vents of
the unit.
• Do not operate the heater
if the flame becomes dark
& sooty of if the firepot
overfills with pellets. Turn
the MODE SWITCH to
"OFF" and periodically
inspect the heater (see
"Running Your Heater").
© Travis Industries
A
A
A
A
AA
A
AA
A
AA
AA
A
A
AA
AA
AAA
AAA
AA
AA
AA
AA
4070806
• Allow the heater to cool
before carrying out any
maintenance or cleaning.
Ashes must be disposed
in a metal container with a
tight lid and placed on a
non-combustible surface
well away from the home
or structure.
• This heater is designed
and approved for
pelletized wood fuel or a
mixture up to 50% corn,
50% pellets. See page 25
for details on using a corn
pellet mix.
100-01191_000
Safety Precautions
?
• The heater will not operate
during a power outage. If
a power outage does
occur, check the heater
for smoke spillage and
open a window if any
smoke spills into the room.
• This heater must be
connected to a standard
115 V., 60 Hz grounded
electrical outlet. Do not
use an adapter plug or
sever the grounding plug.
Do not route the electrical
cord underneath, in front
of, or over the heater.
• Keep foreign objects out
of the hopper.
• When installed in a mobile
home, the heater must be
bolted to the floor, have
outside air, and NOT BE
INSTALLED IN THE
BEDROOM (Per H.U.D.
requirements). Check
with local building officials.
Mobile
Home
• Disconnect the power
cord before performing
any maintenance.
NOTE:
Turning the Mode Switch
to "OFF" does not
disconnect all power to
the heater.
This
Manual
5
• The exhaust system
should be checked twice a
year minimum for any
build-up of soot or
creosote.
• Do not throw this manual
away. This manual has
important operating and
maintenance instructions
that you will need at a later
time. Always follow the
instructions in this manual.
• Do not touch the hot
surfaces of the heater.
Educate all children of the
danger of a hightemperature heater.
Young children should be
supervised when they are
in the same room as the
heater.
• Do not place clothing or
other flammable items on
or near the heater.
Because this heater can
be controlled by a
thermostat there is a
possibility of the heater
turning on and igniting any
items placed on or near it.
• Travis Industries, Inc.
grants no warranty,
implied or stated, for
the installation or
maintenance of your
heater, and assumes
no responsibility of
any consequential
damage(s).
© Travis Industries
4070806
100-01191_000
Specifications
6
Heating Specifications
Approximate Maximum Heating Capacity (in square feet)* ........................................800 to 2,250 Sq. Feet
Burn Rate (Pounds per Hour)**............................................................................1.7 to 5.5
Maximum Burn Time on Low Burn** ......................................................................29 Hours
Hopper Capacity ..............................................................................................50 Pounds
*
Heating capacity will vary depending on the home's floor plan, degree of insulation, and the outside temperature. It is also affected
by the fuel size, quality, and moisture level.
**
Small pellets will increase or decrease the stated burn rates and burn times. Differences of plus or minus 20% depending on fuel
quality may occur.
Dimensions
27-1/4"
25"
Ce
r
nte
Lin
e
7-3/4"
17-1/4"
4" Diameter
Exhaust
27"
27-3/4"
NOTE:
Measure front and side clearances from the
Weight: 390 Lbs.
stove top. Rear and corner clearances are
measured from the stove body.
Electrical Specifications
Electrical Rating.........................................................................................115 Volts, 3.6 Amps, 60 Hz
Watts During Start-Up Sequence ...................................................................400 (approximately)
Watts During Operation ...............................................................................180 (approximately)
Fuel
• This heater is designed and approved for pelletized wood fuel or a mixture up to 50% corn, 50% pellets.
See page 25 for details on using a corn pellet mix.
EPA Compliance
This heater has been tested exempt from EPA Phase II Requirements by OMNI-Test Laboratories, Inc.
© Travis Industries
4070806
100-01191_000
Installation
7
(For Qualified Installers Only)
Before You Begin
READ THIS ENTIRE MANUAL BEFORE YOU INSTALL AND USE THIS HEATER.
FAILURE TO FOLLOW THE INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE,
BODILY INJURY, OR EVEN DEATH.
Check with local building officials for any permits required for installation of this pellet heater and notify
your insurance company before proceeding with installation.
Packing List
• Thermostat & Wire
• Scraper Rod Tool
• Brush
• Spare Fuse
• Bottle Brush
• Door Tool
• (2) Floor Mounting Brackets
Installation Options
•
•
•
•
•
Residential or Mobile Home (see the section "Mobile Home Requirements")
Alcove Compatible (see the section "Alcove Installation")
Horizontal or Vertical Vent
Outside Air Compatible
Vent with L-Vent, L-Vent Fireplace Liner, or Type A Chimney (with adapter)
Planning The Installation
HINT:
HINT:
HINT:
HINT:
Have an authorized Travis Industries dealer install this heater. If you install the heater
yourself, have your dealer review your installation plans.
Sketch out a detailed plan of the installation including dimensions. Then verify the
dimensions with the requirements listed in this manual.
When determining the location of the stove, locate the wall studs (for horizontal
penetrations) and ceiling trusses (for vertical penetrations). You may wish to adjust the
stove position slightly to ensure the vent does not intersect with a framing member.
Place the heater outside and load 10 pounds of pellets inside the hopper. Plug the
heater in and let it run on HIGH until the pellets run out. This will cure the paint and burn
off any oil on the steel, eliminating any smell inside the home.
Stove Placement
•
•
HINT:
•
Stove must be placed so that no combustibles are within, or can swing within (e.g. drapes,
doors), 36" of the front of the heater.
If the stove is placed in a location where the ceiling height is less than 7', it must follow the
requirements in the section "Alcove Installation Requirements".
REDUCING CLEARANCES - Clearances may be reduced by methods specified in NFPA
211, listed wall shields, pipe shields, or other means approved by local building or fire
officials.
Heater and floor protection must be installed on a level, secure floor.
Floor Protection Requirements
•
•
The heater must be installed on a non-combustible floor protector extending the full width
and depth of the heater and extending 6" in front (minimum 27-3/4" wide by 31" deep)
(minimum .018" thick - 26 gauge) .
Must extend under and 2" to each side and rear of a "Tee" (if used).
© Travis Industries
4070806
100-01191_000
Installation
8
(For Qualified Installers Only)
Clearances - Straight Installation
Through the Wall Installations
A
A
A
A
A
A
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
Interior Vertical Vents
Vent
Clearance*
3” Minimum
2”
Minimum**
“Tee”
7” Minimum
6” Minimum
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
7” Minimum
Floor Protection
Clearances - Corner Installation
6” Minimum
AAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAAAA
AAAAAAAAAAAAA
Through the Wall Vents
Interior Vertical Vents
3” Minimum
2”
Minimum*
*
3” Minimum
45° Elbow
“Tee”
Vent
Clearance*
3” Minimum
3”
Minimum
6” Minimum
45°
6” Minimum
*
Install vent at clearance specified by the vent manufacturer.
NOTE: If interior vertical vent is used, the stove to backwall dimension is determined by the vent
being used. This dimension will vary depending on the brand of pellet vent used. To determine the
distance from the backwall to the stove, connect the "Tee" and add the vent clearance .
** The floor protection must extend 2” or to the wall (whichever is less) – all vent clearances must be met.
© Travis Industries
4070806
100-01191_000
Installation
9
(For Qualified Installers Only)
Venting the Pellet Stove
•
INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT
MANUFACTURER.
•
DO NOT CONNECT THE PELLET VENT TO A VENT SERVING ANY
OTHER APPLIANCE OR STOVE.
•
DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM
OF THIS UNIT.
•
USE AN APPROVED WALL THIMBLE WHEN PASSING THE VENT
THROUGH WALLS AND A CEILING SUPPORT/FIRE STOP SPACER
WHEN PASSING THE VENT THROUGH CEILINGS (MAKE SURE TO
MAINTAIN CLEARANCE TO ANY COMBUSTIBLES).
•
No more than one tee and 180° of elbows (one tee with two 90° elbows, one tee with one
90° and two 45° elbows, etc.).
33 Feet
(max.)
Maximum Venting
Distance
•
Vent must have a support
bracket every 5' of pellet vent
when exterior of structure
30 Feet
The vent height and run
must not exceed the
distance shown in the
shaded region shown to the
right.
25 Feet
20 Feet
Venting into this shaded
area may require restrictor
adjustments. See the
section “Restrictor
Adjustment” for details.
15 Feet
10 Feet
NOTE: To achieve optimum
performance, we
recommend keeping the
vent as short as possible
(horizontal run especially).
5 Feet
© Travis Industries
4070806
10 Feet
(max.)
5 Feet
0 Feet
0 Feet
100-01191_000
Installation
10
(For Qualified Installers Only)
Pellet Vent Type
•
Must be 4" diameter Type "L" (except for masonry fireplace installations) - or - connect the
vent to a factory built type "A" chimney. All vent joints (including adapters, elbows, etc…)
must be sealed with 500° F. RTV silicone.
Installing the Pellet Vent
Seal each vent section (including
adapters, elbows, etc...) by
injecting a liberal amount of 500°
F. RTV silicone into the gap
between sections.
V
RT
F.
0 ° ne
0
5 ico
Sil
•
Horizontal sections must have a 1/4" rise every 12" of travel.
•
Pellet vent connections must be sealed airtight with 500° F. RTV silicone and screwed
together with at least three sheet metal screws.
Pellet Vent Termination
•
Vent must terminate on the exterior of the dwelling. Horizontal terminations must protrude a
minimum12" from the wall. Vertical terminations must protrude a minimum 24" from the roof
surface. In addition, all clearances listed below must be met.
•
Must have an approved cap (to prevent water from entering) or a 45° downturn with rodent screen.
•
If the termination is located on a windy side of the house, an approved house shield is
recommended to prevent soot from building up on the side of the house.
•
Must not be located where it will become plugged by snow or other material.
H
G
X
A
F
B
D
C
F
H
A
E
NOTE: Measure clearances to the nearest edge of the exhaust hood.
A
B
C
D
E
F
G
H
X
Minimum 4' clearance below or beside any door or window that opens
(This clearance may be reduced to18” if using outside air (see page 11) – we recommend
the door or window be kept closed during operation.
Minimum 1’ clearance below or beside any window that does not open.
Minimum 1' clearance above any door or window that opens
Minimum 2' clearance from any adjacent building
Minimum 7' clearance above any grade when adjacent to public walkways
NOTE: Vent may not terminate in covered walkway or breezeway.
Minimum 2' clearance above any grass, plants, or other combustible materials
Minimum 3' clearance from any forced air intake of any other appliance
Minimum 2' clearance below eaves or overhangs
Minimum 1' clearance horizontally from combustible wall
Must be a minimum of 2' above the roof
© Travis Industries
4070806
100-01191_000
Installation
11
(For Qualified Installers Only)
Mobile Home Requirements
•
Outside air is required (used for
combustion) - see the directions
below.
•
The heater must be bolted to the
floor (Some states do not require
this; check with your local building
department). See the illustration
to the right.
•
The heater must be grounded to
the steel chassis of the mobile
home (Some states do not require
this; check with your local building
department).
WARNING:
DO NOT INSTALL IN
SLEEPING ROOM.
CAUTION:
THE STRUCTURAL
INTEGRITY OF THE
MANUFACTURED HOME
FLOOR, WALL, AND
CEILING/ROOF MUST BE
MAINTAINED.
The leveling bolts in the legs may be used
in conjunction with the included clips (sku
210-03924) to secure the stove to the floor.
Outside Air (used for combustion)
•
Must not be drawn from an enclosed space (garage, unventilated crawl space).
HINT:
Travis Industries strongly suggests outside air for all residential installations, especially for
those that are energy efficient, air-tight homes.
•
Must not be over 15' long.
•
Must be made with 3" diameter or larger metal or aluminum duct with a metal screen attached to
the end to keep out rodents (P.V.C. or other combustible materials may not be used). We
recommend the Travis Industries Outside Air Kit (part # 99200139).
•
Must not terminate above or within 1' of the chimney termination.
•
Must have a rain cap or down-turned elbow to prevent water from entering.
•
Must be located so that it will not become plugged by snow or other material.
A screen is required to prevent
rodents from entering.
Botttom of Stove
3” Air Duct
(99200136 includes 4’ length)
AAAAA
Air may be drawn from a ventilated crawl space.
Use a hose clamp to secure the
A
aluminum air duct to the air inlet
flange on the stove.
Air Duct (3” Dia.)
Outside air entrance must be placed so it
does not become blocked by snow.
© Travis Industries
4070806
100-01191_000
Installation
12
(For Qualified Installers Only)
Alcove Installation Requirements
When the pellet stove is placed in a location where the ceiling height is less than 7' tall, it is considered
an alcove installation. Because of the reduced height, the requirements listed below must be met.
•
Minimum height is 55"
•
Maximum depth is 48"
•
Minimum width is 41-1/4"
•
Minimum clearance of 7" on each side and 3" on back
Baffle Installation
Install the baffles included with the stove (see page 29 for details).
Door Seal Verification
The door is aligned prior to leaving the factory. However, shipping and installation may cause the door to
become mis-aligned. Verify the door is correctly aligned and seals properly (see the section "Door Seal"
under Yearly Maintenance).
Restrictor Adjustment
The restrictor is used to adjust airflow to the firepot. It should be adjusted to match the heat output setting
and burn the pellets at the appropriate rate. This keeps the firepot as clean as possible.
For low heat output settings the restrictor will need to be closed or near closed to limit the amount of air.
This prevents the stove from burning the pellet fuel faster than it is fed.
For medium heat output settings the restrictor will need to be opened to a medium position.
For high heat output settings the restrictor will need to be opened to a high position. This prevents the
firepot from over-filling with pellets and becoming clogged with ash clumps.
Keeping your firepot clean is the most important step to maintaining a safe and efficient stove. Check and
clean your firepot daily until you find the correct restrictor settings and appropriate firepot cleaning interval.
Not Enough Air
If clinkers (ashes that solidify into a clump)
develop or the flame appears lazy and slow
to blow the ash out of the firepot, pull the
restrictor outward until the flame becomes
active and the firepot holes remain clean.
NOTE: If the restrictor is fully out, yet the
firepot does not remain clean, the stove
needs to be cleaned and checked for air
leaks (see “Maintenance” section of this
manual).
Too Much Air
If the flames are too active (small, flickering
flames) or if burning pellets are expelled
from the firepot, move the restrictor rod
inwards until the flame slows down and no
burning pellets are expelled (note: it is okay
to have “glowing embers” jump out of the
firepot). Another symptom of too much air
is the heater “blowing the fire out” – a
condition in which the pellets burn faster
than they are fed (this is most common on
low).
© Travis Industries
A
4070806
100-01191_000
Installation
(For Qualified Installers Only)
13
Thermostat Installation
!
Do not connect 120 VAC to the thermostat circuit of this heater (do not use a
household thermostat used for a wall-board or other electical heater).
A thermostat is included with this heater (part # 99300650). Follow the directions below to install.
1
Attach the thermostat
wire to the circuit board
(see the illustration
below). Route the wire
through the back of the
heater (away from any hot
or moving components).
Pull the cover off the thermostat
50
60
70
80
90
50 60 70 80 90
Run the thermostat wires
through the wall (cut off excess
wire, leaving 6” of slack).
Robertshaw
Attach the quick-connects
to the two posts near the
molex connector on the
circuit board (orientation
does not mater).
2
3
Expose 1/2” of wire and
attach to these two posts.
Determine a location for
the thermostat that is
within range of the 20'
length of thermostat wire.
It should be centralized in
the room and away from
the heater. The wire may
be routed externally on
the wall or behind the wall
(preferred).
Standard
Screwdriver
Follow the directions to
the right to attach the
thermostat and
thermostat wires.
© Travis Industries
Attach the thermostat to
the wall through these
two holes.
4070806
100-01191_000
14
Installation
(For Qualified Installers Only)
Installation Example: Direct "Through-the-wall" Installation
Horizontal Rain Cap
12” Minimum
Type "L" Vent
A
A
A
A
A
A
A
A
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
A
A
A
A
A
A
AAA A
A
A
A
A
A A
A
A
A
A
A
A
A
A
AAAAAAAAAAAA
AAAAAAAAAAAAAAAA
A
AAAAAAAAAAAAA
House Shield (used to protect
exterior wall from soot
discoloration) is HIGHLY
RECOMMENDED
Wall Thimble
(note clearance
between vent and
combustibles)
3” Minimum
Seal each vent
section (including
adapters, elbows,
etc...) by injecting a
liberal amount of
500° F. RTV
silicone into the gap
between sections.
V
RT
F.
0° e
50 ilicon
S
7” Minimum
6” Minimum
Floor Protection
3” Minimum
12”
Minimum
Floor Protection
17-1/4”
© Travis Industries
4070806
100-01191_000
Installation
(For Qualified Installers Only)
Installation Example: Interior Vertical Installation
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
Vent
Clearance*
2”
Minimum
“Tee”
7” Minimum
Floor Protection
6” Minimum
Vertical Cap
AAAAAAAAAAAAAA
AAAAAAAAAAAAAA
AAAAAAAAAAAAAA
AAA
AAAAAAAAAAAAAA
AAA
AAAAAAAAAAAAAA
AAAAAAA
AAA
AAAAAAAAAAAAAA
AAA
AAAAAAA
AAAAAAAAAAAAAA
AAAA
AAAAAAA
A
A
AA
A
AAA
AA
A AAA
AAA
A
A
A
A
A
A
A
A
A
AAAAAAAAAAAAAAA
A
AAAAAAAAAAAAA
24” Minimum
Storm Collar
Roof Flashing
Insulation
must maintain
clearance.
Vent must
maintain
clearance to
combustibles.
Ceiling Support / Fire Stop Spacer
Seal each vent
section (including
“L” Vent
TV
R
F.
0° e
50 licon
Si
Vent
Clearance*
adapters, elbows,
etc...) by injecting a
liberal amount of
500° F. RTV
silicone into the gap
between sections.
2” Min.
Floor Protection
Outside air may be drawn from
a ventilated crawl space.
*
Install vent at clearance specified by the vent manufacturer.
© Travis Industries
4070806
100-01191_000
15
16
Installation
(For Qualified Installers Only)
Installation Example: Class A Chimney Retrofit
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAA
AAAAA
AAAA
AAAA
AAAA
AAAAAAAAAAAAAAA
AAAA
AAAAAAAAAAAAAAA
AAAA
AAAAAAAAAAAAAAA
AAAA
AAAAA
AAAAAAAAAAAAAAA
AAAA
AAAAA
AAAAAAAAAAAAAAA
AAAAA
AAAA
AAAAAAAAAAAAAAA
AAAAA
AAAA
AAAAAAAAAAAAAAA
AAAA
AAAAAAAAAAAAAAA
AAAAAA
A
AAAAA
A
AAA
A
A
AA
AAA
AAA
A
AA
AAA
A
AA
A
A
A
A
A
A
A
A
A
AAAAAAAAAAAAAAAAAAA
A
AAAAAAAAAAAAAAA
Vent
Clearance*
“Tee”
2”
Minimum
7” Minimum
Floor Protection
Seal each vent
section (including
6” Minimum
V
RT
F.
0° e
50ilicon
S
Class A Chimney
Storm Collar
adapters, elbows,
etc...) by injecting a
liberal amount of
500° F. RTV
silicone into the gap
between sections.
Roof Flashing
Class A Chimney must
maintain clearances outlined
in the chimney’s installation
instructions (usually 2”).
Class A Chimney Ceiling Support
“L” Vent to Class A Chimney Adapter
“L” Vent
Vent
Clearance*
2” Min.
Floor Protection
Outside air may be drawn from
a ventilated crawl space.
*
Install vent at clearance specified by the vent manufacturer.
© Travis Industries
4070806
100-01191_000
Installation
(For Qualified Installers Only)
Installation Example: Masonry Fireplace Hearth Stove
Vertical Cap
“L” Vent
Cover Plate (non-combustible)
AAAAA
AAAA
AAAAA
AAA
AA
AA
A
AA
AAAA
AAA
AA
A
A
AAAAAA
AA
AAAAAAAAA
AAAA
AA
AA
AAA
AA
AAAA
AAAA
AA
AA
AAA
AA
AAAA
AAAAAA
AAAA
AA
AAA
AA
AA
AA
AAA
AA
AA
AA
AAAA
AAA
AA
AA
AAAA
AAA
AA
AA
AA AAAA
AAA
AA
AA
AAAAA AAAAA
AA
AA
AAAA
AA AAAAAA AAAAA
AA
AA
AA
AAAA
AA
AAAAA
AAAAA
AA
AAAA
AAAAA
AA
AA
AAAAA
AA
AA
AAA
AAAA
AA
AA
AAAAA
AAA
AAAA
AA
AA
AA
AA
AAAAA
AA
AA
AAAAA
AA
AA
AAA
AAAAA
AA
AA
AAA
AAAAA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AAA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AAA
AA
AA
AA
A
AA
A
AA
AAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AA
AA
AA
AA
AA
AAAA
AA
Storm Collar
one
Silic
Seal the cover
plate with silicone.
Seal each vent
section (including
adapters, elbows,
etc...) by injecting a
V
RT
F.
0° e
5 0 ilicon
S
liberal amount of
500° F. RTV
silicone into the gap
between sections.
“L” Vent Flex
Section
Allow room for the
hopper lid to open
44”
Lintel
Outside air
may be
drawn from
the ash
cleanout.
6” Min.
NOTE: you may need a short horizontal section here to
clear the lintel and allow the hopper lid to open.
© Travis Industries
4070806
100-01191_000
17
18
Installation
(For Qualified Installers Only)
Installation Example: Zero-Clearance (Metal) Fireplace Hearth Stove
Vertical Cap
Storm Collar
“L” Vent
AAAA
AAAA
AAAA
AAAA
“L” Vent Flex
Section
Cover Plate (non-combustible)
one
Silic
Seal the cover
plate with silicone.
AA
AA
AAAA
AA
AAAA
AA
AAAA
AA
AAAA
AA
AAAA
AA
AAAA
AA
AAAA
AA
AAAA
AAAAA
AAAA
AAAA
AA
AAAAA
AAAA
AA
AAAA
AAAA
AAAA
AA
AAAA
AAAA
AAAAAA
AAAAAA
AAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAA
AAA
AAA
AAAA
AAA
AAA
AAAAAA
AAAA
AAA
Seal each vent
section (including
adapters, elbows,
etc...) by injecting a
liberal amount of
500° F. RTV
silicone into the gap
between sections.
V
RT
F.
0° e
5 0 ilicon
S
Allow room for the
hopper lid to open
44”
6” Min.
NOTE: you may need a short horizontal section here to
clear the lintel and allow the hopper lid to open.
© Travis Industries
4070806
100-01191_000
Installation
19
(For Qualified Installers Only)
Installation Example: Freestanding Masonry Chimney
Vertical Cap
“L” Vent
Cover Plate (non-combustible)
Storm Collar
AAA
AAAA
AA
AAAA
AAA
AA
AAA
AAAAAAA
AAAAA
AA
AAA
AA
AAA
AAA
AA
AAAAA
AA
AAA
AAAAA
AAA
AA
AAAA
AAAAA
AA
AAA
AAAAA
AAA
AA
AAAA
AAAAA
AA
AAAAAAAA
AAA
AA
AAAA
AAAAA
AAAA
AA
AAA
AAA
AA
AAAAA
AA
AAA
AAA
AA
AA
AAAAAAAA
AAA
AA
AA
AAA
AAAAA
AAA
AA
AAAAA
AA
AAA
AAA
AA
AA
AAAAAAAA
AAAAA
AAAAA
AA
AAA
AAA
AA
AA
AAAAAAAA
AAA
AA
AA
AAA
AAAAA
AAA
AA
AAAAA
AA
AAA
AA
AAA
AAAAA
AA
AAA
AAA
AA
AA
AAA
AAA
AA
AAA
AAAAA
AA
AAAAA
AA
AAA
AAA
AA
AA
AAA
AAAAA
AAAAA
AAAAA
AA
AAA
AAA
AA
AA
AAA
AAA
AA
AAAAA
AA
AAA
AAA
AA
AAAAA
AA
AAA
AAA
AA
AAA
AAA
AA
AA
AAA
AAAAA
AA
AA
AAA
AAA
AA
AA
AAA
AAA
AA
AA
AAA
AAA
AA
AA
AAA AAA
AAAAA
AA
AA
AAA
AA
AAAAAAAAAAAAAAAAAAA
AA
AAAAAAAAAAA
AAA
AAA
AA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAA
AAA
AAAAAAAAAAA
AAA
one
Silic
Seal the cover
plate with silicone.
V
RT
F.
0° e
50ilicon
S
“L” Vent Flex
Section
Seal each vent
section (including
adapters, elbows,
etc...) by injecting a
liberal amount of
500° F. RTV
silicone into the gap
between sections.
“L” Vent
Sections
Vent
Clearance*
Allow room for the
hopper lid to open
44”
Clean-Out Access
6” Min.
*
Install vent at clearance specified by the vent manufacturer.
© Travis Industries
4070806
100-01191_000
Operation
20
Safety Notice
Read this entire manual (especially the "Safety Precautions" on pages 4 and 5)
before using this stove. Failure to follow the instructions may result in property
damage, bodily injury, or even death.
!
Do not unplug the stove to turn it off. This stove relies upon electricity to push the flue
gases out the pellet vent – unplugging it may lead to smoke entering your room.
!
Failure to maintain your heater will lead to a restricted combustion air system, leading to
poor performance and in some cases, smoke spillage into the room. See the
"Maintenance" section for details.
Location of Controls
Control Panel
Three tabs are provided on the
back of the stove to hang the
cleaning
tools (bend
the tabs out).
Firepot
TIM
ER
Tim
e
e
Can
cel
Set
A
u
t
Tim
o
RO
OM
TE
M
P
MIN
SET
TEM
P
OF
F
°F
°F
Thermostat or Remote
(required for Auto Operation)
Starting the Heater for the First Time
AAA
AAA
AAA
Restrictor
The restrictor adjusts
the amount of air
flowing to the firepot.
Start the Heater - Let it Burn for 1 Hour - THEN OPEN THE DOOR
The stove paint is cured through heat. To prevent it from bonding to the door gasket, you must burn
the heater for approximately 1 hour, then open and close the door to break any bonding.
Curing the Paint
This stove uses a heat-activated paint that will
emit some fumes while starting the first fire.
Open doors and windows to the room to vent
these fumes. You may also notice oil burning
off of the interior of the stove. This ruststopping agent will soon dissipate.
Priming the Auger
2 to 4 hours
AA
AA
A
AAA
A
Because of its electronic control panel, this stove does not require priming. If you run out of pellets
you may notice it will take approximately 5 minutes longer for the stove to start.
© Travis Industries
4070806
100-01191_000
Operation
21
Loading Pellets
Lift the hopper lid to its vertical position. Pour pellets into the hopper until full. NOTE: The hopper
holds approximately 50 pounds of pellets.
To Open the Hopper Lid:
Lift the hopper lid from this handle.
Pe ll ets
AAAAAA
AAAAAAAAAA
AA
AAAAAAAA
AAAAAAAAAA
AAAAAA
AAAAAAAA
AAAAAAAAAA
AAAAAA
AAAAAAAA
AAAAAA
AAAAAAAAAA
AAAAAA
AAAAAA
AAAAAAAAAA
AAAAAA
AAAAAA
Warning:
The front edge of the
stove top becomes very
hot, do not touch this
area below the handle.
HINT:
NOTE:
The auger automatically shuts off when the hopper
lid is open. If loading pellets while the heater is on,
make sure to close the lid as soon as possible.
This prevents the heater from shutting off due to
lack of pellets in the firepot.
To prevent the pellet stove from inadvertently shutting down due to the auger disabling switch, we
recommend pressing the “START” button after reloading the stove.
The Two Modes of Operation
Manual
Manual mode requires the user to turn
the heater on and off manually.
Auto (requires a thermostat)
Auto mode allows you to use a
thermostat to control room
temperature. The stove automatically
turns on when the temperature drops
below the thermostat setting. Once the
stove reaches operating temperature,
the stove then runs at the heat output
setting selected.
Switching Modes While in
Operation
Whenever the stove is switched from
one mode to another while in
operation, the stove will enter the "startup" sequence for a minimum of 20
minutes.
DISCONNECT POWER BEFORE SERVICE
H
E
A
T
O
U
T
P
U
T
H
E
A
T
HIGH
MED
LOW
AUTO
MANUAL
These indicator lights
AUGER
are used to determine
MAINT.
which mode you are in.
(REQUIRED)
UP
AUTO
OFF
MANUAL
DOWN
MANUAL
Use the mode
switch to
determine the
mode.
F
A
N
START
UP
MANUAL
DOWN
AUGER
TM
TRAVIS INDUSTRIES
HOUSE OF FIRE
© Travis Industries
4070806
100-01191_000
Operation
22
Manual Mode
Manual mode requires the user to turn the
heater on and off manually.
H
E
A
T
To Start
Press the "Manual Start" button. That's it. The
stove automatically goes to a medium burn rate
and high fan while the igniter starts the fire
burning within 10 minutes. During this period
the lowest “HEAT OUTPUT” light will flash. If
the stove does not start in 30 minutes, the
stove turns off.
F
A
N
AUTO
OFF
MANUAL
UP
MANUAL
DOWN
START
UP
MANUAL
DOWN
AUGER
Once up to temperature, the stove will then
run at the heat output setting selected on the
control panel (see “To Adjust the Heat” below).
TM
TRAVIS INDUSTRIES
HOUSE OF FIRE
To Shut Down
Move the mode switch to "OFF". The exhaust
blower will still run until the heater cools down.
UP
H
E
A
T
AUTO
OFF
MANUAL
MANUAL
DOWN
START
UP
F
A
N
MANUAL
DOWN
AUGER
TM
TRAVIS INDUSTRIES
HOUSE OF FIRE
DISCONNECT POWER BEFORE SERVICE
H
E
A
T
To Adjust the Heat
O
U
T
P
U
T
Press the "Heat” buttons to adjust the heat
output.
NOTE: During start-up you may adjust the heat
setting. This heat setting will take affect once
the start-up sequence is complete.
H
E
A
T
F
A
N
HIGH
MED
LOW
AUTO
MANUAL
AUGER
MAINT.
(REQUIRED)
UP
AUTO
OFF
MANUAL
DOWN
MANUAL
These lights
indicate the
heat output
setting.
NOTE: the
lights may
be difficult to
see from an
angle.
START
UP
MANUAL
DOWN
AUGER
TM
Press the
“up” or
“down”
button to
adjust the
heat output.
TRAVIS INDUSTRIES
HOUSE OF FIRE
© Travis Industries
4070806
100-01191_000
Operation
23
Auto Mode
Auto mode allows you to use a thermostat to control room temperature. The stove automatically turns
on when the temperature drops below the thermostat setting. Once the stove reaches operating
temperature, the stove then runs at the heat output setting selected.
To Adjust Room Temperature (or Start the Stove)
Move the thermostat to the heat setting desired. If the room is
cooler than the setting, the stove will go through the start-up
sequence for approximately 10 minutes. During this period the
lowest “HEAT OUTPUT” light will flash. Once up to temperature,
the stove will then run at the heat output setting selected on the
control panel. If the room is too hot, move the thermostat to a
lesser setting.
DISCONNECT POWER BEFORE SERVICE
H
E
A
T
To Adjust the Heat
Press the "Heat” buttons to adjust the heat
output.
O
U
T
P
U
T
HINT:
If you find that the stove turns on and off
repeatedly, you may wish to turn the heat
output to a lesser setting. The lower setting
will provide a more consistent heat output over
time, eliminating the need for the thermostat to
repeatedly turn the stove off.
NOTE:
If the thermostat calls for heat while the stove is
still cooling down, the stove will go through the
start-up sequence (for a minimum of 20
minutes).
H
E
A
T
F
A
N
HIGH
AUTO
MANUAL
MED
AUGER
LOW
MAINT.
(REQUIRED)
UP
AUTO
OFF
MANUAL
MANUAL
DOWN
These lights
indicate the
heat output
setting.
NOTE: the
lights may
be difficult to
see from an
angle.
START
UP
MANUAL
DOWN
AUGER
Press the
“up” or
“down”
button to
adjust the
heat output.
TM
TRAVIS INDUSTRIES
HOUSE OF FIRE
To Shut Down
Move the mode switch to "OFF". The exhaust
blower will still run until the heater cools down.
H
E
A
T
F
A
N
UP
AUTO
OFF
MANUAL
DOWN
MANUAL
START
UP
MANUAL
DOWN
AUGER
TM
TRAVIS INDUSTRIES
HOUSE OF FIRE
© Travis Industries
4070806
100-01191_000
Operation
24
Restrictor Adjustment
The restrictor is used to adjust airflow to the firepot. It should be adjusted to match the heat output setting
and burn the pellets at the appropriate rate. This keeps the firepot as clean as possible.
For low heat output settings the restrictor will need to be closed or near closed to limit the amount of air.
This prevents the stove from burning the pellet fuel faster than it is fed.
For medium heat output settings the restrictor will need to be opened to a medium position.
For high heat output settings the restrictor will need to be opened to a high position. This prevents the
firepot from over-filling with pellets and becoming clogged with ash clumps.
Keeping your firepot clean is the most important step to maintaining a safe and efficient stove. Check and
clean your firepot daily until you find the correct restrictor settings and appropriate firepot cleaning interval.
Not Enough Air
If clinkers (ashes that solidify into a clump)
develop or the flame appears lazy and slow to
blow the ash out of the firepot, pull the
restrictor outward until the flame becomes
active and the firepot holes remain clean.
NOTE: If the restrictor is fully out, yet the firepot
does not remain clean, the stove needs to be
cleaned and checked for air leaks (see
“Maintenance” section of this manual).
Too Much Air
If the flames are too active (small, flickering
flames) or if burning pellets are expelled from
the firepot, move the restrictor rod inwards until
the flame slows down and no burning pellets
are expelled (note: it is okay to have “glowing
embers” jump out of the firepot). Another
symptom of too much air is the heater “blowing
the fire out” – a condition in which the pellets
burn faster than they are fed (this is most
common on low).
AA
AA
Adjusting the Fan Speed
H
E
A
T
F
A
N
UP
Press the “up” or “down”
AUTO
OFF
MANUAL
DOWN
button to adjust the fan
speed.
MANUAL
START
UP
MANUAL
DOWN
AUGER
NOTE: When adjusting
the fan speed the HEAT
TM
OUTPUT lights will flash
TRAVIS INDUSTRIES
HOUSE OF FIRE
the fan speed setting for
one second.
© Travis Industries
4070806
100-01191_000
Operation
25
Start-Up Sequence
This stove utilizes a start-up sequence whenever the mode switch is changed or the heater is started
when cold. This is to ensure proper operation through all possible settings and operational states (hot
or cold, pellets burning or not burning, etc.). This sequence over-rides all user settings (except the
"OFF" position) to set the auger feed rate to medium, the exhaust blower to high, and the igniter on.
During this period the lowest “HEAT OUTPUT” light will flash.
"AUGER ON" Light
This light comes on when the auger is turning. This allows the operator to determine when the auger
is turning.
"Maintenance Required" Light
N O T E: If the “MAINTENACE REQUIRED” light
comes on, check the items below before calling
for service.
DISCONNECT POWER BEFORE SERVICE
H
E
A
T
The “MAINTENACE REQUIRED” light is used to
indicate maintenance is required on the heater. It
will turn on due to various operating circumstances.
When it turns on, a second light will turn on near
“HEAT OUTPUT” (see the illustration to the right).
Determine the maintenance code (2, 4, or 6), then
use the chart below to diagnose and remedy the
situation.
O
U
T
P
U
T
HIGH
MED
LOW
# 6 Light
(red)
# 4 Light
(yellow)
AUTO
# 2 Light
(green)
MANUAL
AUGER
MAINT.
(REQUIRED)
Light
Likely Cause
Remedy
2
(green)
• Heavy Ash Build-Up in Exhaust Duct
• Clean the Firebox (see page 34)
• Heavy Ash Build-Up in Exhaust
Housing or Plugged Tubing
• Clean the Exhaust Housing and Tubing (see page
36)
• Heavy Ash Build-Up in Vent
• Clean the Vent (see page 37)
•
Heater Ran Out of Pellets
•
Refill the Hopper (see page 21)
•
Heater Did Not Start-Up Correctly
•
Re-Start the Heater and Verify the Pellets Ignite
after 10 Minutes
•
Power Outage
•
Re-Start the Heater (see page 26)
•
Restrictor Not Set Properly
•
Re-Start the Heater and Monitor Restrictor
Setting (see page 24)
•
Burnpot Clogged
•
Clean Burnpot (see page 28)
•
Air Leak
•
Verify Door, Glass, and Ashpan Seal Correctly
(see page 37)
•
Heavy Ash Build-Up
•
Clean the Firebox (see page 34), Exhaust
Housing (see page 36), and Vent (see page 37)
•
Electrical Input Error (voltage or mhz
fluctuation, amp deficiency, etc.)
•
Unplug the Heater then Plug it Back In (this restarts the circuit board)
•
Components Over-Heated
•
Clean the Heater and Vent (a plugged heater will
slow exhaust flow, increasing temperatures –
see pages 34- 37)
•
Faulty Wiring / System Fault
•
If this Fault Persists, Contact Your Dealer
4
(yellow)
6
(red)
© Travis Industries
4070806
100-01191_000
Operation
26
"MANUAL AUGER" Button
This button turns the auger on. It is used to “prime” the auger after the hopper has run out of pellets.
Power Outages
If a sustained power outage occurs while in "Manual", the stove will go to a "cool down" mode to
vacate smoke once power returns. If the power outage was short, the heater will go to the start-up
sequence. If in "Auto", the stove will re-start (if the room is cool).
!
Because this stove relies upon a blower to evacuate the smoke, some smoke may enter
the home during a power outage. To keep to a minimum, leave the door closed.
Using a Pellet/Corn Mix with This Heater
This heater may burn a mixture of corn and wood pellets up to a 50% - 50% proportion by volume.
Shelled corn burned in Travis pellet appliances must be clean (free of husk and cob residue) and have
a moisture content no greater than 15%.
DO NOT BURN A MIX WITH MORE THAN 50% CORN TO WOOD PELLETS.
THOROUGHLY MIX THE TWO FUELS TOGETHER TO BE SURE OF AN
EVEN BURN RATE.
•
If combustion is slow, if the fire is slow to start, or if clinkers (ashes that solidify into a clump)
build up rapidly in the fire pot, decrease the proportion of corn and increase the proportion
of wood pellets until you find a proportion that works well in your appliance.
•
If your stove or insert is operated with a thermostat, you may notice the automatic igniter at
times fails to light a 50/50 corn to pellet mix. If you experience this, decrease the proportion
of corn and increase the proportion of wood pellets in the mix.
For an optimum fire and greatest efficiency, it is important to keep the fire pot free of built up ashes. If
you are burning only high quality wood pellets, you should check and clean the fire pot at least every
two weeks or after ten bags of pellets.
If the pellets you are burning have a high ash content or if you burn a corn/wood pellet mixture, we
recommend that you check the fire pot every day and clean it if necessary.
© Travis Industries
4070806
100-01191_000
Maintenance
27
Daily Maintenance (whenever using the stove)
Inspect the Burn
When burning on high, the
flames should be bright orange
with embers jumping from the
firepot.
NOTE: the optimal restrictor
position will vary over time as soot
builds up inside the exhaust
system. See "Restrictor
Adjustment" for details.
Make Sure Pellets are
Not Piling Up
If the pellets pile up over the burn
pot, turn the mode switch to
"OFF".
A
AA
AA
AA
AA
AA
AAA
AAA
AA
AA
AA
AA
A
AA
A
AA
A
A
AA
AA
AA
A
The most likely causes are:
•
Restrictor needs adjustment
(see “Restrictor Adjustment”
in the installation section of
this manual)
•
The door, glass, or ashpan is
open or has an air leak
•
The firepot requires cleaning
•
The exhaust system requires
cleaning
© Travis Industries
4070806
100-01191_000
Maintenance
28
Daily Maintenance (whenever using the stove) - Continued
Check Firepot for
Clinkers
If the flames seem to be
coming only from the sides,
or are orange/black, turn
the heater off and check for
clinkers (ashes that solidify
into a clump).
A
AA
A
A
AA
AA
AA
AA
AA
A
A
AA
A
A
The most likely causes are:
•
Restrictor needs
adjustment (see
“Restrictor
Adjustment” in the
installation section of
this manual)
•
Poor pellet quality
•
The door or glass has
an air leak
•
The exhaust system
requires cleaning
Cleaning the Firepot
WARNING:
Make sure the heater
has fully cooled
(approximately 25
minutes) before
opening the door and
conducting service.
A
AA
AA
AA
A
A
AA
AA
To clean the firepot, open
the door (see page 27) and
knock away any debris on
the firepot with a
screwdriver. If severely
clogged, remove the
firepot to gain better
access.
© Travis Industries
4070806
100-01191_000
Maintenance
29
Daily Maintenance (whenever using the stove) - Continued
Door Opening
WARNING: Make sure the heater
has fully cooled
(approximately 25
minutes) before
opening the door and
conducting service.
Open the latch.
Swing the
doors open.
WARNING: Do not swing the doors past 90°. This may cause the doors to
strike the body of the stove and cause damage.
NOTE: When closing the doors, close the left door first. Then shut the right
door and tighten the latch.
© Travis Industries
4070806
100-01191_000
Maintenance
30
Weekly Maintenance (or every 5 bags of pellets)
Flyash Removal
This heater was designed to allow for easy flyash removal with the included tools. However, to ease
maintenance, several pellet stove owners have purchased vacuums specifically made to remove
flyash. Furthermore, some of these vacuums are heat-resistant to allow for flyash removal while it is still
warm. Do not use a standard vacuum on this appliance (except to clean the pellet dust out
of the hopper). Standard vacuums may spread the fine particles inside the flyash into the home and
are not heat-resistant (hot flyash may cause the internal portion of vacuums to ignite).
Clean the Hopper
Run the stove until the pellets run out. Open the hopper and remove the dust and debris near the
bottom of the hopper.
Clean the Heat Exchange Tubes
Use the included tool to move the
heat exchanger rod up and down.
NOTE: The tool hangs on
the back of the stove.
WARNING:
The front edge of the
stove becomes very hot,
do not touch the area
below the handle.
Keep the door closed so the
flyash does not enter the room.
© Travis Industries
4070806
100-01191_000
Maintenance
31
Weekly Maintenance (or every 5 bags of pellets) - continued
Clean the Baffles
WARNING: Make sure the heater has fully cooled (approximately 25 minutes) before conducting service.
HINT:
The more often you clean out flyash, the more efficient your heater will burn.
The baffles are found along the top of the firebox. The front edge has a slot that slides into a hook on
the top of the firebox. The back rests on the back refractory. To remove, slide them inwards, pull
them forward, and tilt them back to allow the accumulated flyash fall off into the firebox. Replace after
cleaning.
Move the baffle forward and tilt the back down.
This allows any built-up flyash to fall off the top
of the baffle.
Push up on the front portion of the left
baffle and slide it to the right. Note how
the rear edge of the baffle rests on the
rear refractory.
The right side baffle is removed
in the same fashion. Note how
the right side baffle is larger
than the left side baffle.
© Travis Industries
4070806
100-01191_000
Maintenance
32
Weekly Maintenance (or every 5 bags of pellets) - continued
Sweep Ash Into Ashpan
WARNING: Make sure the heater has fully cooled (approximately 25 minutes) before conducting service.
Remove the two ashdump covers on the floor of the firebox using the included hook tool. Remove
the firepot and place it aside. Sweep accumulated flyash through the holes in the firebox floor into the
ashpan. Replace the covers and firepot after cleaning.
Lift the firepot out of the firebox.
Use the included hook tool to remove the
ashdump covers (both side).
Use the included brush to
sweep all flyash into the
ashpan.
Make sure to sweep flyash from
the firepot holder.
© Travis Industries
4070806
100-01191_000
Maintenance
33
Weekly Maintenance (or every 5 bags of pellets) - continued
Check Ashpan, Dispose if necessary
WARNING: Make sure the heater has fully cooled (approximately 25 minutes) before conducting service.
WARNING: The ashpan must be in place while the heater is in use.
Lift up on the
ashlip and slide
the ashpan
forward.
AAAAA
AAAAA
AAAAA
AA
Twist the ashpan
handle clockwise.
AA
AA
A handle is provided
on the ashpan to
remove the ashes.
AAAAAAA
AAAAA
AAAAAAA
AA
Disposal of Ashes – Ashes should be placed in a metal container with a tight fitting lid. The closed
container of ashes should be placed on a noncombustible floor or on the ground, well
away from all combustible materials, pending final disposal. If the ashes are disposed of
by burial in soil or otherwise locally dispersed, they should be retained in the closed
container until all cinders have been thoroughly cooled.
Clean the Glass
Open the doors and clean the glass with a non-abrasive glass cleaner and rag.
© Travis Industries
4070806
100-01191_000
Maintenance
34
Yearly Maintenance (or every ton)
The following section details extensive maintenance procedures. We strongly suggest
these items be carried out by a trained service technician, possibly by a service agreement
set up with your dealer.
WARNING:
Disconnect the power cord and make sure the heater has fully cooled
prior to conducting service.
Soot and Flyash: Formation and Need for Removal – The products of combustion will
contain small particles of flyash. The flyash will collect in the exhaust venting system and restrict the
flow of the flue gases. Incomplete combustion, such as occurs during startup, shutdown, or incorrect
operation of the room heater will lead to some soot formation which will collect in the exhaust venting
system. The exhaust venting system should be inspected at least once every year to determine if
cleaning is necessary.
Clean the Vertical Exhaust Duct
Remove the baffles at the top of the firebox (see page 31). Remove the firepot and ashdump covers
(see page 32). Remove the side and back refractory (see the pictures below).
Using the included latch tool, remove the two duct covers on the inside of the firebox (see the
pictures below)..
© Travis Industries
4070806
100-01191_000
Maintenance
35
Yearly Maintenance (or every ton) - continued
Remove the button plugs at the top of the firebox (both sides). Once removed, use the bottle brush
to dislodge any flyash from the exhaust channel behind the button plug.
Use the
bottle brush
to clean this
channel.
Button Plug
Use the included bottle brush to remove accumulated flyash from the vertical exhaust channels (both
sides). You may need to bend the bottle brush to allow it to access this area. Remove accumulated
flyash from the horizontal exhaust channels along the perimeter of the firebox and leading to the
exhaust blower. Sweep the flyash out of the exahust channels and into the ashpan.
Vertical Exhaust Channel (behind the
firebox walls – accessed from below).
Horizontal Exhaust Channel
HINT: You can remove dry flyash from the
vertical exhaust channels by “tapping” on
the walls (be careful to prevent flyash from
flying into the air).
© Travis Industries
4070806
100-01191_000
Maintenance
36
Yearly Maintenance (or every ton) - continued
Clean the Exhaust Blower
The exhaust blower cover is held in place with 4 screws.
Remove the
side cover.
Remove the cover plate on the exhaust blower. Clean the area inside the blower, removing all flyash.
Remove these 3 nuts to
expose the exhaust blower.
Use the bottle brush to disoldge any
flyash near the exahust blower and in the
horizontal exhaust channel. Take care
to not damage the impeller on the
exhaust blower.
Flow Switch Tube
Nipple (attached to exhaust channel)
© Travis Industries
Check the nipple and flow switch tube. Insert a pipe
cleaner through the nipple to dislodge any flyash.
NOTE: The flow switch will shut off the auger if the
tube becomes clogged or dislodged. Make sure it is
cleaned out and correctly attached.
4070806
100-01191_000
Maintenance
37
Yearly Maintenance (or every ton) - continued
Clean the Convection Blower
Remove all dust and debris from the convection blower. Take care to prevent damage to the
convection blower impellers.
Clean the Vent
AA
AA
AA
Flyash will deposit along
sections that are horizontal.
Warning:
Make sure the cap is free of debris
(especially if it has a screen that could
become blocked).
AA
AA
AA
Check the vent sections for creosote
accumulation (indicating a poorly burning
stove). Accumulation over 1/4” must be
removed.
On vertically vented systems, the dirtiest portion
is often the point where the vent turns upwards
(i.e. the "Tee"). Fortunately, the "Tee" has a builtin clean-out cover. Place a container under the
“Tee”, disconnect the cover and remove all flyash.
While open, use a flashlight to look up the vent to
check for build-up.
Whenever any portion of the pellet vent is disconnected, the joints must be sealed with
RTV 500° F. silicone sealant.
Adjusting the Door Hinge and Latch
The door latch should pull the door against the face of the stove (but not so tight as to not allow full
handle rotation). To adjust the door latch, adjust the position of the striker plate that attaches to the
front plate of the stove.
Check for Air Leaks Around the Door, Glass, and Ashpan
!
•
•
•
Air leaks into the firebox will decrease the stove's performance greatly, leading to excessive
sooting, inefficient burning, and perhaps a malfunction.
Inspect the door gasket to make sure it is fully attached. Use stove gasket cement to re-attach if
necessary. If the door gasket is worn or flattened, replace.
If the glass is cracked, replace. The glass is held in place by glass clips. See the illustration below
for details.
Remove the ashpan and inspect the gasket around the perimeter of the ashpan. Re-attach, or
replace the gasket if necessary.
© Travis Industries
4070806
100-01191_000
Maintenance
38
Replacement Parts
Door Replacement Parts
6
5
3
1
8
9
7
AAAA
AA
AAA
AAAAAAA
AA
AAAA
AA
AAA
AAAA
AA
AAA
AAAA
AAA
AAAA
AAA
AAAA
4
2
10
ID #
1
3
5
7
9
Description
Door, Left
Door Gasket
Glass Gasket
Glass Clip w Screws, Gasket
Left Door Handle w Hardware
Qty
1
1
1
4
1
Part #
ID #
2
4
6
8
10
Description
Door, Right
Gasket Cement
Glass
Door Hinge w Pins
Right Door Handle w Hardware
Qty
1
1
2
4
1
Part #
Replacement Parts
Description
ASHPAN ASSY - COMPLETE - SERVICE PART
AUGER DRIVE COLLAR, 1997 & UP - LARGE/SMALL PEL STOVE/INS
AUGER FLIGHT INSPECTION COVER - 16 GA EG - 6.812 x 4.674
AUGER FLIGHT, 2000+ LRG PEL - - 2" PITCH
AUGER MOTOR, ALL PS/PI EXCEPT - 93-96 PELLET INSERT (93-0194)
BLOWER, COMB, PELLET - LARGE - 2000 & UP
BLOWER, CONV, P2-8/11-15/G1-2 - 93-95BV, 91-96PS/PI, 00 LRG PS
BRUSH, BROOM STYLE # - REPLACES 93005530 & 93005531
BURN POT, LG PS/PI-CORN & PEL - LRG- PS/PI ONLY - SERVICE PART
CNTRL BRD, ALL PEL 1997 & UP# - LARGE OR SMALL PS & PI
CORD RESTRAINER
DR STRIKER PLATEw/SCRWS - SERVICE PART
DRAFT (FLOW) SWITCH # - ALL PS/PI
DRAFT FLOW TUBING, ALL PS/PI - ALL PELLET FS & INSERTS
FACE HINGE LEAF - SERVICE PART
FUSE - 5AMP CONTROL BOARD# - NEW DIAGNOSTIC BOARD 2006'
FUSE HOLDER (IN-LINE)
FUSE, 5AMP, 5 - FOR INLINE # - FUSE ASSEMBLY - 93 & UP PEL
FUSE, 6AMP, 5 - CONTROL BOARD - 1997 TO 2005' PS & PI
GLASS - ARBOR WOOD - 11.062 x 8.437 SERVICE PART
GLASS RPLCMNT SCRW PAK- ARBOR - 8- STANDARD & 8- OVERSIZE
© Travis Industries
Part #
250-00160
91002021
210-02702
91002013
90-0191
93005535
98900755
100-04301
250-00128
250-00011
100-00112
250-00143
90-0791
99300164
250-00227
250-00081
100-00210
93-0695
93005019
250-00142
250-00179
Description
GROMMET, IGNITOR WIRE - LG P/S - BLACK RUBBER
GSKT, CLEAN-OUT CVR, AST/LG PI - 3.250 x 2.750
GSKT, COMB BLOWER (BODY), LRG - 10.505" x 7.782" x 1/8"
GSKT, COMB BLOWER(MOTOR), LRG - 7.000" dia
GSKT, EXHAUST PLATE - LG PEL# - 4.250" x 4.250"
HOSE NIPPLE, BARBED (DRAFT)
IGNITER, LG PS/PI - 2000 & UP - 250 WATT ELEMENT
OIL PAN, COMB BLOWER - LG PEL - 20 GA ALZ - 5.414 x 1.881
POWER CORD, PS/PI 1997 & UP # - 16 ga AWG w/RING & FML CNCTRS
SHL, ASH DRAWER - ARBOR - CAST IRON - SERVICE PART
SNAP-DISC - 120deg CERAMIC # - NORMALLY OPEN
SNAP-DISC - 120deg NO # - NORMALLY OPEN
SNAP-DISC - 200deg NC # - NORMALLY CLOSED
THERMOSTAT, PELLET
TOOL, GLASS LATCH/RESTRICT0R/ - SCRAPER
WIRE HRNS, PEL, JUMPER, LRG - - PELLET
WIRE HRNS, PEL, PS/PI '2005+ - REPLACES OLD HARNESS 100-00393
WIRE HRNS, THERMOSTAT (20')
4070806
Part #
100-02811
100-03235
100-03206
100-03231
100-03230
100-04307
250-00243
210-03216
93005015
250-00159
100-00232
100-00231
100-00233
100-00250
100-02302
100-00390
250-00017
100-00400
100-01191_000
Normal Operating Sounds
Heat Exchanger Tubes
You may hear the heated air being
forced through these tubes by the
convection fan.
Convection Fan
The modern high efficiency fan
may produce a low hum,
particularly on "HIGH". This
sound will change as the FAN
setting is changed.
Exhaust Blower
This blower may create a
low-pitched hum. This
sound will change as the
HEAT OUTPUT is altered.
Firepot
As pellets are fed into the
firepot, a light clicking
sound may be heard.
© Travis Industries
Auger Motor
When feeding pellets, you
may hear the intermittent
buzz of this motor running.
4070806
100-01191_000
39
Safety Label
40
© Travis Industries
4070806
100-01191_000
Limited 7 Year Warranty
41
To register your TRAVIS INDUSTRIES, INC. 7 Year Warranty, complete the enclosed warranty card and mail it within ten (10) days of the appliance
purchase date to: TRAVIS INDUSTRIES, INC., 4800 Harbour Pointe Blvd. SW, Mukilteo, WA 98275. TRAVIS INDUSTRIES, INC. warrants this
appliance (appliance is defined as the equipment manufactured by Travis Industries, Inc.) to be defect-free in material and workmanship to the original
purchaser from the date of purchase as follows:
Check with your dealer in advance for any costs to you when arranging a warranty call.
Mileage or service charges are not covered by this warranty. This charge can vary from store to store.
Years 1 & 2 - COVERAGE: PARTS & LABOR
Firebox Assembly:
Ceramic Glass
Accessories
Firepot, Firepot Holder, Ash Cleanout Doors, Ashbox or Ash
Dump, Cast Fireback, Heat Exchanger Tubes, Exhaust
Manifold, Exhaust Box
Glass (breakage from thermal shock)
Ceramic Log with Log Shelf, Remote
Igniter System
Re-Installation Allowance
Door Assembly:
Door Frame, Latch Assembly, Glass Retainers
Auger Assembly
Auger Flight, Auger Tube, Auger Bushings
Igniter, Igniter Leads
Electrical System
In cases where heater must be removed from home for repairs, a
partial cost of re-installation is covered (pre-authorization required)
Auger Motor, Convection Blower, Exhaust Blower, Circuit
Board, Snap Disks, Wiring Harness, Vacuum Switch
One-Way Freight Allowance
Cast Iron Parts
One-way freight allowance on pre-authorized repair done at factory
is covered.
Warranted against breakage, cracking, or burn through
Exclusions:
Paint, Gasketing
Years 3 Through 5 - COVERAGE: PARTS & LABOR
Firebox Assembly:
Door Assembly:
Firepot, Firepot Holder, Ash Cleanout Doors, Ashbox or Ash
Dump, Cast Fireback, Heat Exchanger Tubes, Exhaust
Manifold, Exhaust Box
One-Way Freight Allowance
Door Frame, Latch Assembly, Glass Retainers
One-way freight allowance on pre-authorized repair done at
factory is covered.
Auger Assembly
Auger Flight, Auger Tube, Auger Bushings
Exclusions:
Paint, Gasketing, Ceramic Glass, Igniter System, Electrical System, Cast Iron Parts, Accessories, Re-Installation Allowance
Years 6 & 7 - COVERAGE: PARTS ONLY
Firebox Assembly:
Door Assembly:
Firepot, Firepot Holder, Ash Cleanout Doors, Ashbox or Ash Dump, Cast
Fireback, Heat Exchanger Tubes, Exhaust Manifold, Exhaust Box
Door Frame, Latch Assembly, Glass Retainers
Exclusions:
Paint, Gasketing, Ceramic Glass, Igniter System, Electrical System, Cast Iron Parts, Accessories, Auger Assembly, Re-Installation
Allowance, One-Way Freight Allowance, Labor
CONDITIONS & EXCLUSIONS
1.
2.
3.
4.
5.
6.
7.
30.
31.
10.
11.
12.
13.
14.
15.
16.
17.
This new appliance must be installed by a qualified installer. It must be installed, operated, and maintained at all times in accordance with the instructions in
the Owner’s Manual. Any alteration, willful abuse, accident, neglect, or misuse of the product shall nullify this warranty.
This warranty is nontransferable, and is made to the ORIGINAL purchaser, provided that the purchase was made through an authorized Travis dealer.
Discoloration and some minor expansion, contraction, or movement of certain parts and resulting noise, is normal and not a defect and, therefore, not covered
under warranty.
The warranty, as outlined within this document, does not apply to the chimney components or other Non-Travis accessories used in conjunction with the
installation of this product. If in doubt as to the extent of this warranty, contact your authorized Travis retailer before installation.
Travis Industries will not be responsible for inadequate performance caused by environmental conditions such as nearby trees, buildings, roof tops, wind, hills
or mountains or negative pressure or other influences from mechanical systems such as furnaces, fans, clothes dryers, etc.
This Warranty is void if:
a.
The unit has been operated in atmospheres contaminated by chlorine, fluorine or other damaging chemicals.
b.
The unit is subject to submersion in water or prolonged periods of dampness or condensation.
c.
Any damage to the unit, combustion chamber, heat exchanger or other components due to water, or weather damage which is the result of, but not limited
to, improper chimney/venting installation.
Exclusions to this 7 Year Warranty include: injury, loss of use, damage, failure to function due to accident, negligence, misuse, improper installation,
alteration or adjustment of the manufacturer's settings of components, lack of proper and regular maintenance, damage incurred while the appliance is in
transit, alteration, or act of God.
This 7 Year warranty excludes damage caused by normal wear and tear, such as paint discoloration or chipping, worn or torn gasketing, chipped or cracked
firebrick, etc. Also excluded is damage to the unit caused by abuse, improper installation, modification of the unit, or the use of fuel other than that for which
the unit is configured.
Damage to gold or nickel surfaces caused by fingerprints, scratches, melted items, or other external sources left on the gold or nickel from the use of cleaners
other than denatured alcohol is not covered in this warranty.
TRAVIS INDUSTRIES, INC. is free of liability for any damages caused by the appliance, as well as inconvenience expenses and materials. Incidental or
consequential damages are not covered by this warranty. In some states, the exclusion of incidental or consequential damage may not apply.
This warranty does not cover any loss or damage incurred by the use or removal of any component or apparatus to or from the Travis appliance without the
express written permission of TRAVIS INDUSTRIES, INC. and bearing a TRAVIS INDUSTRIES, INC. label of approval.
Any statement or representation of Travis products and their performance contained in Travis advertising, packaging literature, or printed material is not part of
this 7 year warranty.
This warranty is automatically voided if the appliance’s serial number has been removed or altered in any way. If the appliance is used for commercial
purposes, it is excluded from this warranty.
No dealer, distributor, or similar person has the authority to represent or warrant Travis products beyond the terms contained within this warranty. TRAVIS
INDUSTRIES, INC. assumes no liability for such warranties or representations.
Travis Industries will not cover the cost of the removal or re-installation of hearths, facing, mantels, venting or other components.
If for any reason any section of this warranty is declared invalid, the balance of the warranty remains in effect and all other clauses shall remain in effect.
This 7 year warranty is the only warranty supplied by Travis Industries, Inc., the manufacturer of the appliance. All other warranties, whether express or
implied, are hereby expressly disclaimed and purchaser’s recourse is expressly limited to the warranties set forth herein.
IF WARRANTY SERVICE IS NEEDED:
1.
2.
3.
4.
If you discover a problem that you believe is covered by this warranty, you MUST REPORT it to your Travis dealer WITHIN 30 DAYS, giving them proof of purchase, the purchase date, and the
model name and serial number.
Travis Industries has the option of either repairing or replacing the defective component.
If your dealer is unable to repair your appliance’s defect, he may process a warranty claim through TRAVIS INDUSTRIES, INC., including the name of the dealership where you purchased the
appliance, a copy of your receipt showing the date of the appliance’s purchase, and the serial number on your appliance. At that time, you may be asked to ship your appliance, freight charges prepaid,
to TRAVIS INDUSTRIES, INC. TRAVIS INDUSTRIES, INC., at its option, will repair or replace, free of charge, your appliance if it is found to be defective in material or workmanship within the
time frame stated within this 7 year warranty. TRAVIS INDUSTRIES, INC. will return your appliance, freight charges (years 1 to 5) prepaid by TRAVIS INDUSTRIES, INC., to your regional
distributor, or dealership.
Check with your dealer in advance for any costs to you when arranging a warranty call. Mileage or service charges are not covered by this warranty. This charge can vary from store to
store.
© Travis Industries
4070806
100-01191_000
Index
42
"AUGER ON" Light..............................................25
Adjusting the Door Hinge and Latch .......................37
Alcove Installation Requirements ..........................12
Auto Mode ........................................................23
Baffle Installation...............................................12
Before You Begin ...............................................7
Weekly Maintenance (or every 5 bags of pellets) ......30
Check Ashpan, Dispose if necessary.....................33
Check Firepot for Clinkers....................................28
Check forAirLeaks AroundtheDoor, Glass, andAshpan ............37
Clean the Baffles ...............................................31
Clean the Convection Blower ................................37
Clean the Exhaust Blower ....................................36
Clean the Glass .................................................33
Clean the Heat Exchange Tubes ...........................30
Clean the Hopper ...............................................30
Clean the Vent...................................................37
Clean the Vertical Exhaust Duct............................34
Cleaning the Firepot............................................28
Clearances - Corner Installation ............................8
Clearances - Straight Installation ..........................8
Daily Maintenance (whenever using the stove).........27
Dimensions.......................................................6
Door Seal Verification .........................................12
Electrical Specifications......................................6
EPA Compliance ................................................6
Floor Protection Requirements..............................7
Flyash Removal .................................................30
Fuel.................................................................6
Heating Specifications ........................................6
Important Information .........................................2
Inspect the Burn ................................................27
Installation Example: Class A Chimney Retrofit ........16
InstallationExample: Direct "Through-the-wall"Installation.............14
InstallationExample: FreestandingMasonry Chimney................19
Installation Example: Interior Vertical Installation ....15
InstallationExample: Masonry FireplaceHearthStove.......................17
InstallationExample: Zero-Clearance(Metal)FireplaceHearthStove..18
Installation Options ............................................7
Installing the Pellet Vent......................................10
Introduction ......................................................2
© Travis Industries
Loading Pellets ................................................. 21
Location of Controls ........................................... 20
"Maintenance Required" Light............................... 25
Make Sure Pellets are Not Piling Up ....................... 27
Manual Mode .................................................... 22
Maximum Venting Distance.................................. 9
Mobile Home Requirements.................................. 11
Normal Operating Sounds.................................... 39
Outside Air (used for combustion) ......................... 11
Packing List ..................................................... 7
Pellet Vent Termination ....................................... 10
Pellet Vent Type ................................................ 10
Planning The Installation ..................................... 7
Power Outages ................................................. 26
Replacement Parts ............................................ 38
Restrictor Adjustment......................................... 12
Restrictor Adjustment......................................... 24
Safety Label ..................................................... 40
Safety Notice.................................................... 20
Safety Precautions ............................................ 4
Starting the Heater for the First Time...................... 20
Start-Up Sequence ............................................ 25
Stove Placement ............................................... 7
Sweep Ash Into Ashpan ...................................... 32
The Two Modes of Operation ................................ 21
Thermostat Installation ....................................... 13
Venting the Pellet Stove...................................... 9
Warranty.......................................................... 41
Yearly Maintenance (or every ton)......................... 34
4070806
100-01191_000