Alliance Laundry Systems UW100TV Specifications

Pocket Hardmount
UniLinc
Refer to Page 5 for Model Numbers
35 – 125 Models
PHM1400C
PHM1400C
150 Model
PHM1402C
PHM1402C
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
www.alliancelaundry.com
Part No. F8138601R12
October 2012
Installation
Washer-Extractors
Table of
Contents
Safety Information..............................................................................
Explanation of Safety Messages...........................................................
Important Safety Instructions ...............................................................
Safety Decals ........................................................................................
Operator Safety.....................................................................................
2
2
2
4
4
Introduction.........................................................................................
Model Identification .............................................................................
Delivery Inspection...............................................................................
Name plate Location.............................................................................
Nameplate Location - UniLinc Models ...........................................
Replacement Parts ................................................................................
Customer Service..................................................................................
5
5
6
6
6
6
6
Specifications and Dimensions...........................................................
Machine Dimensions ............................................................................
UWTV Models ................................................................................
Machine Foundation Requirements......................................................
Concrete Foundation Pad Installation...................................................
Floor Load Data ...............................................................................
Mounting Bolt Installation Requirements ............................................
Machine Mounting and Grouting.....................................................
Mounting Bolt Hole Locations .............................................................
Grout Placement ...................................................................................
Gap Setting for Vibration Switch ....................................................
Drain Connection Requirements...........................................................
Water Connection .................................................................................
Electrical Installation Requirements.....................................................
Steam Requirements (Steam Heat Option Only)..................................
Chemical Injection Supply System.......................................................
External Supplies ..................................................................................
Chemical Injection Using Internal 24VAC Control Transformer ...
Chemical injection Using External AC Power Source ....................
External Supply Signals ...................................................................
8
10
10
13
14
16
17
18
19
24
25
29
31
33
36
37
40
40
41
42
© Copyright 2012, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
1
Safety Information
Explanation of Safety Messages
Precautionary statements (“DANGER,” “WARNING,”
and “CAUTION”), followed by specific instructions,
are found in this manual and on machine decals. These
precautions are intended for the personal safety of the
operator, user, servicer, and those maintaining the
machine.
DANGER
DANGER indicates an imminently
hazardous situation that, if not avoided,
will cause severe personal injury or
death.
WARNING
WARNING indicates a hazardous situation
that, if not avoided, could cause severe
personal injury or death.
CAUTION
CAUTION indicates a hazardous situation
that, if not avoided, may cause minor or
moderate personal injury or property
damage.
Additional precautionary statements (“IMPORTANT”
and “NOTE”) are followed by specific instructions.
IMPORTANT: The word “IMPORTANT” is used
to inform the reader of specific procedures where
minor machine damage will occur if the procedure
is not followed.
NOTE: The word “NOTE” is used to communicate
installation, operation, maintenance or servicing
information that is important but not hazard
related.
Important Safety Instructions
WARNING
To reduce the risk of fire, electric shock,
serious injury or death to persons when
using your washer, follow these basic
precautions:
W023
1. Read all instructions before using the washer.
2. Install the washer according the
INSTALLATION instructions. Refer to the
GROUNDING instructions in the
INSTALLATION manual for the proper
grounding of the washer. All connections for
water, drain, electrical power and grounding must
comply with local codes and be made by licensed
personnel when required. It is recommended that
the machine be installed by qualified technicians.
3. Do not install or store the washer where it will be
exposed to water and/or weather.
4. To prevent fire and explosion, keep the area
around machine free from flammable and
combustible products. Do not add the following
substances or textiles containing traces of the
following substances to the wash water: gasoline,
kerosene, waxes, cooking oils, vegetable oils,
machine oils, dry-cleaning solvents, flammable
chemicals, thinners, or other flammable or
explosive substances. These substances give off
vapors that could ignite, explode or cause the
fabric to catch fire by itself.
5. Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for two weeks or more. HYDROGEN GAS
IS EXPLOSIVE. If the hot water system has not
been used for such a period, before using a
washing machine or combination washer-dryer,
turn on all hot water faucets and let the water
flow from each for several minutes. This will
release any accumulated hydrogen gas. The gas
is flammable, do not smoke or use an open flame
during this time.
6. To reduce the risk of an electric shock or fire, DO
NOT use an extension cord or an adapter to
connect the washer to the electrical power
source.
2
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Safety Information
7. Do not allow children to play on or in the washer.
Close supervision of children is necessary when
the washer is used near children. This appliance
is not intended for use by young children or
infirm persons without supervision. Young
children should be supervised to ensure that they
do not play with the appliance. This is a safety
rule for all appliances.
8. DO NOT reach and/or climb into the tub or onto
the washer, ESPECIALLY if the wash drum is
moving. This is an imminently hazardous
situation that, if not avoided, will cause severe
personal injury or death.
9. Never operate the washer with any guards, panels
and/or parts removed or broken. DO NOT bypass
any safety devices or tamper with the controls.
10. Use washer only for its intended purpose,
washing textiles. Never wash machine parts or
automotive parts in the machine. This could
result in serious damage to the basket or tub.
11. Use only low-sudsing, no-foaming types of
commercial detergent. Be aware that hazardous
chemicals may be present. Wear hand and eye
protection when adding detergents and
chemicals. Always read and follow
manufacturer’s instructions on packages of
laundry and cleaning aids. Heed all warnings or
precautions. To reduce the risk of poisoning or
chemical burns, keep them out of the reach of
children at all times (preferably in a locked
cabinet).
12. Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
13. Always follow the fabric care instructions
supplied by the textile manufacturer.
14. Loading door MUST BE CLOSED any time the
washer is to fill, tumble or spin. DO NOT bypass
the loading door switch by permitting the washer
to operate with the loading door open. Do not
attempt to open the door until the washer has
drained and all moving parts have stopped.
15. Be aware that hot water is used to flush the
supply dispenser. Avoid opening the dispenser lid
while the machine is running.
16. Do not attach anything to the supply dispenser’s
nozzles, if applicable. The air gap must be
maintained.
18. Be sure water connections have a shut-off valve
and that fill hose connections are tight. CLOSE
the shut-off valves at the end of each wash day.
19. Keep washer in good condition. Bumping or
dropping the washer can damage safety features.
If this occurs, have washer checked by a
qualified service person.
20. DANGER: Before inspecting or servicing
machine, power supply must be turned OFF. The
servicer needs to wait for at least 3 minutes after
turning the power OFF and needs to check for
residual voltage with a voltage meter. The
inverter capacitor or EMC filter remains charged
with high voltage for some time after powering
OFF. This is an imminently hazardous situation
that, if not avoided, will cause severe personal
injury or death.
21. Do not repair or replace any part of the washer, or
attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that the user understands and has the
skills to carry out. ALWAYS disconnect the
washer from electrical, power and water supplies
before attempting any service.
22. Disconnect the power cord by grasping the plug,
not the cord. Replace worn power cords and/or
loose plugs. If the supply cord is damaged, it
must be replaced by a special cord or assembly
available from the service agent.
23. Before the washer is removed from service or
discarded, remove the door to the washing
compartment.
24. Failure to install, maintain, and/or operate this
washer according to the manufacturer’s
instructions may result in conditions which can
produce bodily injury and/or property damage.
NOTE: The WARNINGS and IMPORTANT
SAFETY INSTRUCTIONS appearing in this
manual are not meant to cover all possible
conditions and situations that may occur. Common
sense, caution and care must be exercised when
installing, maintaining, or operating the washer.
Any problems or conditions not understood should be
reported to the dealer, distributor, service agent or the
manufacturer.
17. Do not operate the machine without the water
reuse plug or water reuse system in place, if
applicable.
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
3
Safety Information
Operator Safety
WARNING
This machine must be installed, adjusted,
and serviced by qualified electrical
maintenance personnel familiar with the
construction and operation of this type of
machinery. They must also be familiar
with the potential hazards involved.
Failure to observe this warning may result
in personal injury and/or equipment
damage, and may void the warranty.
SW004
IMPORTANT: Ensure that the recommended
clearances for inspection and maintenance are
provided. Never allow the inspection and
maintenance space to be blocked.
WARNING
NEVER insert hands or objects into
basket until it has completely stopped.
Doing so could result in serious injury.
SW012
The following maintenance checks must be performed
daily:
1. Verify that all warning labels are present and
legible, replace as necessary.
2. Check door interlock before starting operation of
the machine:
a. Attempt to start the machine with the door
open. The machine should not start.
b. Close the door without locking it and start the
machine. The machine should not start.
WARNING
Never touch internal or external steam
pipes, connections, or components.
These surfaces can be extremely hot and
will cause severe burns. The steam must
be turned off and the pipe, connections,
and components allowed to cool before
the pipe can be touched.
SW014
c. Attempt to open the door while a cycle is in
progress. The door should not open.
If the door lock and interlock are not functioning
properly, disconnect power and call a service
technician.
3. Do not attempt to operate the machine if any of
the following conditions are present:
a. The door does not remain securely locked
during the entire cycle.
Safety Decals
Safety decals appear at crucial locations on the
machine. Failure to maintain legible safety decals
could result in injury to the operator or service
technician.
Use manufacturer-authorized spare parts to avoid
safety hazards.
b. Excessively high water level is evident.
c. Machine is not connected to a properly
grounded circuit.
WARNING
Operating the machine with severe out-ofbalance loads could result in personal
injury and serious equipment damage.
W728
4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Introduction
Model Identification
Information in this manual is applicable to these
models:
UW35TV
UW60TV
UW80TV
UW100TV
UW125TV
UW150TV
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5
Introduction
This manual is designed as a guide to the installation
of the Pocket Hardmount washer-extractor.
4. Press the
highlighted.
keypad until machine ID is
NOTE: All information, illustrations, and
specifications contained in this manual are based
on the latest product information available at the
time of printing. We reserve the right to make
changes at any time without notice.
5. Press the
keypad.
IMPORTANT: Warranty is void unless washerextractor is installed according to instructions in
this manual. Installation should comply with
minimum specifications and requirements, and
with applicable municipal building codes, water
supply regulations, electrical wiring regulations
and any other relevant statuary regulations. Due to
varied requirements, applicable local codes should
be thoroughly understood and all pre-installation
work arranged for accordingly.
Always provide the machine’s serial number and
model number when ordering parts or when seeking
technical assistance. Refer to Figure 1.
MODEL EXAMPLE OF NAMEPLATE LOCATION
1
2
Delivery Inspection
Upon delivery, visually inspect crate, protective cover,
and unit for any visible shipping damage. If the crate,
protective cover, or unit is damaged or signs of
possible damage are evident, have the carrier note the
condition on the shipping papers before the shipping
receipt is signed, or advise the carrier of the condition
as soon as it is discovered.
Remove the crate and protective cover as soon after
delivery as possible. If any damage is discovered upon
removal of the crate and/or protective cover, advise the
carrier and file a written claim immediately.
PHM1400C
PHM1400C
1
2
In Control (UniLinc Models)
At Back of Machine
Figure 1
Name plate Location
Replacement Parts
The nameplate is located on the back of the machine.
Always provide the machine’s serial number and
model number when ordering parts or when seeking
technical assistance. Refer to Figure 1 and Figure 2.
If literature or replacement parts are required, contact
the source from which the washer-extractor was
purchased or contact Alliance Laundry Systems LLC
at (920) 748-3950 for the name of the nearest
authorized parts distributor. A parts manual may be
ordered by returning the reply card provided with each
washer-extractor.
Nameplate Location - UniLinc Models
On UniLinc models, nameplate information is also
programmed into the control. To access machine ID
through the control:
1. Press and hold
, then
keypads at the same time.
6
, then
2. Press the
highlighted.
keypad until Diagnostic is
3. Press the
keypad.
Customer Service
For technical assistance, contact your local distributor
or call:
(920) 748-3121
Ripon, Wisconsin
A record of each washer-extractor is on file with the
manufacturer. Always provide the machine’s serial
number and model number when ordering parts or
when seeking technical assistance. Refer to Figure 1
and Figure 2.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Introduction
Model Number Familiarization Guide
Sample Model Number: UW60TVQU10001
UW
Model Number Prefix
60
Washer-Extractor Capacity (60 pounds dry weight of laundry)
T
Type of Electrical Control
T = UniLinc Control
V
Washer-Extractor Speed Capabilities
V = 8 Speeds
Q
Electrical Characteristics
Refer to Table 7.
U1
Design Series
0001
Option Identification (varies from machine to machine)
UW060TVQU10001
00000000000
200 – 240
19
30
50 – 60
3
60
3
720
27
500000
EXAMPLE OF SERIAL PLATE
PHM697N
PHM697N
Figure 2
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
7
Specifications and Dimensions
.
Specifications
35
60
80
100
125
150
Overall width, in (mm)
32.5 (826)
36.625 (930)
41.5 (1054)
41.5 (1054)
48 (1219)
50.25 (1277)
Overall height, in (mm)
55.5 (1410)
64.5 (1638)
68.5 (1740)
68.5 (1740)
72 (1829)
79 (2007)
Overall depth, in (mm)
43.625 (1108)
45 (1143)
51.5 (1308)
54.5 (1384)
58 (1473)
63 (1600)
1300 (590)
1730 (785)
1770 (805)
2420 (1100)
2970 (1347)
Overall Dimensions
Weight And Shipping Information
Net weight, lb (kg)
1030 (468)
Basket Weight, lb (kg)
150 (68)
200 (92)
330 (150)
360 (163)
550 (250)
572 (260)*
1085 (493)
1340 (608)
1795 (814)
1835 (832)
2525 (1148)
3022 (1371)
66 (1.9)
84 (2.4)
119 (3.4)
119 (3.4)
166 (4.7)
172 (4.87)
Domestic shipping dimensions,
WxDxH, in (mm)
38x47x64
(970x1200x
1630)
40x49x74.5
(1016x1245x
1892)
44x60.5 x77.25
(1118x1537x
1962)
44x60.5x77.25
(1118x1537x
1962)
61.5x60x77.75
(1560x1520x
1980)
54.5x69x79
(139x176x
201)
Export shipping weight, lb (kg)
1150 (522)
1464 (664)
1990 (903)
2030 (921)
2800 (1270)
3350 (1520)
78 (2.2)
96 (2.7)
134 (3.8)
134 (3.8)
184 (5.3)
220 (6.3)
41x50x65.5
(1050x1280x
1670)
43x52.125x74.5
(1092x1324x
1892)
47x63.5x77.25
(1194x1613x
1962)
47x63.5x77.25
(1194x1613x
1962)
63.5x63x80
(1620x1610x
2030)
61.5x71x87
(1562x1804x
2210)
Cylinder diameter, in (mm)
26.25 (667)
32 (813)
36 (914)
36 (914)
42 (1067)
43 (1093)
Cylinder depth, in (mm)
18.375 (467)
20 (508)
21 (533)
27 (686)
24 (610)
27.8125 (706)
5.76 (163)
9.31 (264)
12.4 (350)
15.9 (450)
19.2 (544)
23.4 (662)
Perforation size, in (mm)
0.1875 (4.8)
0.1875 (4.8)
0.1875 (4.8)
0.1875 (4.8)
0.1875 (4.8)
0.1875 (4.8)
Perforation open area, %
18
22
23
23
24
21.5
Door opening size, in (mm)
14.375 (365)
17.5 (445)
17.5 (445)
17.5 (445)
20 (508)
24.75 (629)
Height of door bottom above floor,
in (mm)
23.75 (603)
28.25 (718)
29 (737)
29 (737)
29 (737)
32 (813)
1
1
1
1
1
1
5.0 (3.7)
5.0 (3.7)
7.5 (5.6)
7.5 (5.6)
10 (7.5)
10 (7.5)
Domestic shipping weight, lb (kg)
Domestic shipping volume,
ft3 (m3)
3
3
Export shipping volume, ft (m )
Export shipping dimensions,
WxDxH, in (mm)
Wash Cylinder Information
Cylinder volume,
ft3
(l)
Door Opening Information
Drive Train Information
Number of motors in drive train
Drive motor power, hp (kW)
* Basket Only
(Continued)
8
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
(Continued)
Specifications
35
60
80
100
125
150
Cylinder Speeds / Centrifugal Force Data
1/2 Wash/reverse, rpm (g)
26 (.25)
26 (.31)
26 (.35)
26 (.35)
26 (.40)
23 (.31)
Wash/reverse, rpm (g)
42 (.66)
40 (.73)
40 (.82)
40 (.82)
37 (.82)
36 (0.8)
Distribution, rpm (g)
83 (2.57)
71 (2.29)
73 (2.57)
70 (2.50)
62 (2.29)
61 (2.29)
Very Low extract, rpm (g)
401 (60)
364 (60)
343 (60)
343 (60)
317 (60)
314 (60)
Low extract rpm (g)
568 (120)
514 (120)
485 (120)
485 (120)
449 (120)
444 (120)
Medium extract, rpm (g)
695 (180)
630 (180)
594 (180)
594 (180)
550 (180)
543 (180)
High extract, rpm (g)
803 (240)
727 (240)
686 (240)
686 (240)
565 (190)
627 (240)
Very High extract, rpm (g)
898 (300)
813 (300)
766 (300)
766 (300)
579 (200)
701 (300)
STD
STD
STD
STD
STD
STD
0.5 (13)
0.5 (13)
0.5 (13)
0.5 (13)
0.75 (19)
0.75 (19)
1
1
1
1
1
1
LOW
2.1 (1.5)
3.3 (2.4)
4.6 (3.3)
5.7 (4.1)
6.7 (4.9)
8.3 (6.0)
MED
2.3 (1.7)
3.7 (2.6)
5.2 (3.8)
6.5 (4.7)
7.8 (5.6)
9.5 (6.9)
HIGH
2.7 (1.9)
4.1 (2.9)
6.1 (4.4)
7.6 (5.5)
9.1 (6.6)
11.1 (8.0)
Average consumption per cycle,
BHP (kg)
1.4 (21.4)
2.1 (33.4)
3.1 (48.4)
3.8 (60.4)
4.6 (72.0)
5.8 (91.0)
15.6
27.4
41.2 (Q-Volt)
27.4 (N-Volt)
41.2 (Q-Volt)
27.4 (N-Volt)
N/A
N/A
6
6
9
9
N/A
N/A
2.6
4.2
4.2
4.2
N/A
N/A
2.4 (3.6)
2.4 (3.7)
2.2 (3.4)
2.8 (4.2)
N/A
N/A
Balance Detection
Vibration switch installed
Direct Steam Heating (Optional)
Steam inlet connection size,
in (mm)
Number of steam inlets
Steam required to
raise bath temperature
10°F, lb (10°C, kg)
Electrical Heating (Optional)
Total electrical heating capacity,
kW
Number of electrical heating
elements
Electrical heating element size,
kW
Time required to
raise bath temperature
10°F, min (5°C, min)
F8138601
LOW
MED
2.7 (4.1)
2.7 (4.1)
2.5 (3.9)
3.2 (4.8)
N/A
N/A
HIGH
3.1 (4.7)
3.0 (4.6)
3.0 (4.5)
3.7 (5.6)
N/A
N/A
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9
Specifications and Dimensions
Machine Dimensions
Dimensional Clearances
Allow a minimum of 24 inches (60 cm) at the rear and
6 inches (15.24 cm) at the sides for maintenance,
inspection, and adjustment. Allow at least 6 inches
(15.24 cm) between machines in multiple installations.
NOTE: The dimensions shown here are for
planning purposes only. They are approximate and
subject to normal manufacturing tolerances. If
exact dimensions are required for construction
purposes, contact the distributor or the
manufacturer. We reserve the right to make
changes at any time without notice.
WARNING
Crush hazard.
To avoid personal injury and/or property
damage, do not tip the UW150 machine
more than 25 degrees in any direction.
W642
UWTV Models
(Refer to Figure 3 and Figure 4)
Dimension
35
60
80
100
125
150
in
mm
in
mm
in
mm
in
mm
in
mm
in
mm
A
30.125
765
35.625
905
41.125
1045
41.125
1045
48
1219
50.25
1277
B1
33.375
848
36.625
930
41.5
1054
41.5
1054
48
1219
50.25
1277
C
23.75
603
28.25
718
29
737
29
737
29
737
32
813
D
43.625
1108
45
1143
51.5
1308
54.5
1384
58
1473
63
1600
E2
.5
13
1
25
3
76
3
76
1.5
38
2.9
73
F
55.5
1410
64.5
1638
68.5
1740
68.5
1740
72
1829
79
2007
G2
36
914
36
914
43.75
1111
43.75
1111
48
1219
56
1422
H
8
203
15.5
394
16.875
429
16.875
429
11.375
289
15.75
400
J
43.14
1096
49.8
1265
53.54
1360
53.54
1360
56.4
1433
62.85
1596
K
46.64
1185
53.3
1354
57.04
1449
57.04
1449
59.9
1521
66.35
1685
L
5.12
130
5.12
130.05
7.12
181
7.12
181
7.12
181
7.12
181
M
2.62
66
2.62
66
3.62
92
3.62
92
3.62
92
3.62
92
N
1.37
35
1.37
35
2.25
57
2.25
57
2.25
57
2.25
57
O
3.87
98
3.87
98
5
127
5
127
5
127
5
127
P
2.5
64
2.5
64
2.75
70
2.75
70
2.75
70
2.75
70
Q
2.5
64
2.5
64
3.5
89
3.5
89
3.5
89
3.5
89
1
Overhang dimensions for the optional starch dispenser are as follows:UW35TV, 3.88 inches (9.86 cm); UW60TV, 1.75 inches
(4.45 cm); UW80TV and UW100TV, 0.33 inch (0.83 cm). (The starch dispenser does not overhang the UW125TV.) (No longer
available.)
2 The overhang dimension for the premium wet clean module option (compatible with wet-clean-capable washer-extractors only) adds
24 inches (60.96 cm) to combined machine dimensions E and G.
Table 1
10
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
3
2
3
4
8
5
1
6
7
F
E
C
G (BASE)
D (OVERALL)
A (BASE)
B (OVERALL)
10
L
11
9
M
12
Q
13
16
K
N
P
O
J
15
14
H
UW35TV - UW125TV MODELS
PHM735N
1
2
3
4
5
6
7
8
External Supply Control Mounting Bracket
(Models Through 6/30/08)
Door Unlock Button
Supply Valve Box
Emergency Stop Button
Supply Dispenser
Door Handle
Spray Rinse Nozzle
Recirculation Inlet
9
10
11
12
13
14
15
16
Water Inlet Valves
Steam Connection (Optional)
Shell Vent
Power Input (Electric Heat Models)
Power Input (Non-Electric Heat Models)
Drain (UW80TV, UW100TV and UW125TV
models only)
Drain
Overflow Vent
Figure 3
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
11
Specifications and Dimensions
2
7
3
1
9
4
10
11
5
8
F
J
6
C
G (BASE)
A (BASE)
E
D (OVERALL)
B (OVERALL)
L
12
M
10
Q
13
K
11
15
N
P
O
J
H
14
TMB736N
UW150TV MODELS
PHM736N
1
2
3
4
5
6
7
External Supply Control Mounting Bracket
(Models Through 6/30/08)
Door Unlock Button
Emergency Stop Button
Supply Valve Box
Supply Dispenser
Spray Rinse Nozzle
Door Handle
8
9
10
11
12
13
14
15
Basket Jog Buttons
Recirculation Inlet
Shell Vent
Water Inlet Valves
Steam Connection (Optional)
Power Input
Drain
Overflow Vent
Figure 4
12
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
Machine Foundation Requirements
A 6 inch (153 mm) (for 35 and 60 2-speed, L-speed
and M-speed models) or a 12 inch (305 mm) (for all
other models) thickness of 3500 psi reinforced
concrete foundation is absolutely necessary because of
the high extract speed and the G-forces exerted.
When designing floors or foundations, refer to Table 2
for Floor Load Data for all model sizes. If the
foundation requirements have been met, proceed to
Mounting Bolt Installation Requirements section.
For new foundations a bolt-locator fixture or rebar
frame is available and a preferred option. This rigid
welded assembly made of reinforcing rod and
mounting bolts is designed to be embedded in
concrete. Refer to Figure 7.
The washer-extractor must be anchored to a smooth
level surface so that the entire base of the machine is
supported and rests on the mounting surface. (Do not
support the washer-extractor on only four points.)
Make sure to grout machine. Refer to Figure 6 and
Figure 7.
NOTE: Do not mount on wooden floors, above
ground level, or over basements. Installation must
be “slab on grade” or equal.
Thoroughness of detail must be stressed with all
foundation work to ensure a stable unit installation,
eliminating possibilities of excessive vibration during
extract.
CAUTION
Ensure that the machine is installed on a
floor that is level to within 3/8 inch when
the machine is grouted. Also ensure that
the floor is of sufficient strength and that
the recommended clearances for
inspection and maintenance are provided.
Never allow the inspection and
maintenance space to be blocked.
W760
WARNING
To reduce the risk of fire, this appliance
must be bolted to an uncovered concrete
floor.
W743
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
13
Specifications and Dimensions
Concrete Foundation Pad
Installation
6. Wet the hole around the cement foundation well
and brush the exposed foundation with cement
grout.
A concrete foundation and pad may be constructed to
elevate the machines. Care must be exercised in the
design of the foundation pad due to the force exerted
by the machine during extract. This concrete base
(recommended not to exceed 8 inches [20.32 cm])
(above existing floor) must be poured, reinforced with
rebar and tied to the existing 6 inch (153 mm) (for 35
and 60 2-speed, L-speed and M-speed models) or 12
inch (305 mm) (for all other models) minimum floor.
Refer to Figure 5 and Table 2.
7. Completely fill with a minimum of 6 inch (153
mm) (for 35 and 60 2-speed, L-speed and
M-speed models) or 12 inch (305 mm) (for all
other models) of 3500 psi concrete up to the
existing foundation level plus any added level for
the desired elevated pad. The concrete must be
poured so that the entire foundation and pad
cures as one piece.
IMPORTANT: Do NOT install a pad on top of the
existing floor. The foundation and pad must be
constructed and tied together as one piece.
If the existing floor is not reinforced concrete at least 6
inch (153 mm) (for 35 and 60 2-speed, L-speed and
M-speed models) or 12 inch (305 mm) (for all other
models) thick over a solid foundation, the following
steps must be performed (refer to Figure 5):
8. For new foundations only a bolt-locator fixture
or a rebar frame is available and a preferred
option. Embed the mounting bolts or rebar frame
as the concrete is poured. Ensure that the bolt
threads extend 2 inches (51 mm) for 35 - 125
models and 3 inches (76 mm) for 150 models
above floor level.
9. Allow concrete to dry.
10. Proceed to Machine Mounting and Grouting
section.
1. Cut a hole larger on all sides than the machine
base through the existing floor. The foundation
should extend a minimum of 9 inches (229 mm)
for 35 models or 12 inches (305 mm) for 60 - 150
models out from the machine on all sides.
NOTE: If the washer-extractor installation will
include the Premium Wet Clean Module, the
elevated base must be designed to accommodate the
additional depth of 24 inches (60.96 cm).
2. Excavate to a depth of 18 inches (457 mm) from
the top of the existing floor.
For technical assistance, contact your local distributor
or call Alliance Laundry Systems at (920) 748-3121.
3. Produce a PYRAMID-SHAPED hole by
excavating the bottom of the hole to a width 6
inches wider on each side than the width of the
top of the hole.
4. If installing a foundation and pad, prepare a form
for the above-ground portion of the foundation.
Verify that the top of the foundation is level. The
height of the foundation pad must not exceed 8
inches (203 mm) above the existing floor.
5. Refill with compacted fill dirt, making sure to
allow for correct concrete thickness.
14
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
Brush with
Cement Grout
Brush with
Cement Grout
Brush with
Cement Grout
5
1
3
3
2
LENGTH FOR ONE MACHINE
3
3
4
6
COMPACTED FILL DIRT 18 in. (457 mm) DEPTH
COMPACTED FILL DIRT 18 in. (457 mm) DEPTH
PHM771N
Figure 5
35
1
60
2-Speed,
L-Speed and M-Speed
6 in. (153 mm)
Variable-Speed
12 in. (305 mm)
80
100
125
150
12 in.
(305 mm)
12 in.
(305 mm)
12 in.
(305 mm)
12 in.
(305 mm)
2
6 in.
(152 mm)
minimum
6 in.
(152 mm)
minimum
6 in.
(152 mm)
minimum
6 in.
(152 mm)
minimum
6 in.
(152 mm)
minimum
6 in.
(152 mm)
minimum
3
9 in.
(229 mm)
12 in.
(305 mm)
12 in.
(305 mm)
12 in.
(305 mm)
12 in.
(305 mm)
12 in.
(305 mm)
4
36 in.
(914 mm)
36 in.
(914 mm)
43.75 in.
(1111 mm)
43.75 in.
(1111 mm)
48 in.
(1219 mm)
56 in.
(1422 mm)
5
0 - 8 in.
(0 - 203 mm)
max.
0 - 8 in.
(0 - 203 mm)
max.
0 - 8 in.
(0 - 203 mm)
max.
0 - 8 in.
(0 - 203 mm)
max.
0 - 8 in.
(0 - 203 mm)
max.
0 - 8 in.
(0 - 203 mm)
max.
6
48.125 in.
(1222 mm)
59.625 in.
(1514 mm)
65.125 in.
(1654 mm)
65.125 in.
(1654 mm)
72 in.
(1829 mm)
74.25 in.
(1886 mm)
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
15
Specifications and Dimensions
Floor Load Data
Static and dynamic loads on the floor or foundation are
shown in Table 2.
UWTV Pocket Hardmount Floor Load Data
Specifications
Design
Series
35
60
80
Static floor load, lbs (kN)
U1 and
greater
1272 (5.66) 1677 (7.45) 2292 (10.2)
Static pressure,
lbs/ft2
U1 and
greater
169 (8.08)
187 (8.94)
184 (8.79)
100
125
150
2490 (11.1)
3283 (14.6)
3936 (17.5)
199 (9.6)
205 (9.8)
202 (9.7)
Dynamic floor load, lbs (kN) U1 and
greater
1648 (7.33) 2824 (12.6) 3679 (16.36) 3690 (16.41) 5011 (22.29) 4358 (19.4)
Dynamic pressure,
lbs/ft2 (kN/m2)
219 (10.5)
317 (15.2)
295 (14.2)
295 (14.2)
312 (15)
224 (11)
15
13.6
12.8
12.8
9.7
11.7
U1 and
greater
Dynamic load frequency, Hz U1 and
greater
1
Maximum vertical load,
lbs (kN)
U1 and
greater
2719 (12.1) 4168 (18.5) 5482 (24.38) 5561 (24.73) 7559 (33.62) 7508 (33.4)
2
Minimum vertical load,
lbs (kN)
U1 and
greater
576 (2.56) 1450 (6.45) 1852 (8.24)
Base moment, lb/ft (kN/m)
U1 and
greater
4249 (5.8) 8895 (12.1) 11951 (16.2) 11984 (16.3) 16606 (22.5) 16707 (22.7)
1
2
1794 (8.0)
2434 (10.8)
1208 (5.4)
Acting in the downward direction against the floor.
Acting in the upward direction away from the floor.
Table 2
16
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
Mounting Bolt Installation
Requirements
For new foundations a bolt-locator fixture or rebar
frame is available and a preferred option. This rigid
welded assembly made of reinforcing rod and
mounting bolts is designed to be embedded in
concrete. Refer to Figure 7.
Approved Foundations Only
NOTE: If installing expansion bolts into an
elevated concrete foundation pad, the concrete
foundation pad should extend a minimum of 9
inches (229 mm) for 35 machines or 12 inches (305
mm) for 60 - 150 machines out from the machine
base on all sides. Refer to Figure 5.
1
2
A bolt kit consisting of eight bolts is available as an
option. 35 machines use 5/8-11 x 8 inch bolts.
60 – 125 machines use 3/4-10 x 8 inch bolts. 150
machines use 3/4-10 x 10 inch grade 5 bolts. The bolts
should be embedded in a 3500 psi (241 bar) minimum
reinforced concrete floor that is a minimum of 6 inches
(153 mm) (for 35 and 60 2-speed, L-speed, and
M-speed models) or a 12 inch (305 mm) (for all other
models) thick. Use the mounting bolt layouts in
Mounting Bolt Hole Locations section.
On 35 – 125 machines, the threaded end of the bolts
should extend 2 inches (5.08 cm) above the mounting
surface. On 150 machines, the threaded end of the
bolts should extend 3 inches above the mounting
surface.
Refer to Figure 6 for a typical installation of
individual mounting bolts.
3
4
PHM179N
PHM179N
1
2
3
4
Machine Frame Base
Mounting Bolt Threads
Grouting
Reinforcing Rod
Figure 7
1
2
0.75 in.
(19 mm)
3
2 in.
(51 mm)
4
8 in.
(203 mm)
PHM722N
PHM722N
1
2
3
4
Machine Frame Base
Mounting Bolt Threads
Grouting
Cement or Structural Epoxy
Figure 6
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
17
Specifications and Dimensions
Machine Mounting and Grouting
After the concrete has cured, proceed as follows:
1. Place the washer-extractor adjacent to the
foundation. Do not attempt to move the machine
by pushing on the sides. Always insert a pry bar
or other device under the bottom frame of the
machine to move it.
2. Remove the wood skid by unscrewing the
carriage bolts holding the skid to the bottom
frame of the washer-extractor.
3. Place the washer-extractor carefully over the
anchor bolts. Never attempt to lift the machine by
the door handle or by pushing on the cover
panels.
4. Raise and level the washer-extractor 0.5 inch
(1.27 cm) off the floor on three points, using
spacers such as nut fasteners.
5. Fill the space between the washer-extractor base
and the floor with a good quality non-shrinking
machinery precision grout to ensure a stable
installation. Grout completely under all frame
members. (Remove front panel and back panel to
gain access to all frame members.) Refer to
Figure 13. Force grout under machine base until
all voids are filled.
6. Remove the spacers carefully, allowing the
machine to settle into the wet grout.
18
7. Before grout sets completely, make a drain
opening in the rear of the washer-extractor
grouting with a stiff piece of wire; this opening
should be approximately 1/2 inch (1.27 cm) wide
to allow any surface water build-up under the
base of the machine to drain away. Do not omit
this step.
8. Position the mounting bolt lockwashers and
locknuts on the anchor bolts and finger-tighten
locknuts to machine base.
9. After the grout is completely dry, tighten the
locknuts by even increments – one after the other –
until all are tightened evenly and the washerextractor is fastened securely to the floor.
10. After installing bolts using a rebar frame, torque
5/8 inch bolts (35 model) to 90 ft. lb. and torque
3/4 inch bolts (60-150 models) to 160 ft. lb.
When using bolts not specified by Alliance
Laundry Systems, refer to the specifications
provided with the bolt.
NOTE: Check and retighten the locknuts after five
to ten days of operation and every month
thereafter.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
NOTE: Mounting holes marked “A” need to be
used on all V-Speed Models only.
Mounting Bolt Hole Locations
28.625 in.
(727 mm)
0.75 in.
(19 mm)
A
30.1875 in.
(767 mm)
36 in.
(914 mm)
A
43.28 in.
(1089 mm)
34.16 in.
(868 mm)
2 in.
(51 mm)
26.125 in.
(664 mm)
21.1875 in.
(538 mm)
34.5 in.
(876 mm)
40.1875 in.
(1022 mm)
2 in.
(51 mm)
30.125 in.
(765 mm)
35 MODEL
FRONT OF MACHINE
PHM630N
Figure 8
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
19
Specifications and Dimensions
0.75 in.
(19 mm)
0.75 in.
(19 mm)
34.125 in.
(867 mm)
4.8125 in.
(122 mm)
39.25 in.
(997 mm)
1.25 in.
(32 mm)
36 in.
(914 mm)
9 in.
(229 mm)
44.8125 in.
(1138 mm)
10.75 in.
(273 mm)
1.25 in.
(32 mm)
34.5625 in.
(878 mm)
10.6875 in.
(271 mm)
2 in.
(51 mm)
31.625 in.
(803 mm)
2 in.
(51 mm)
0.75 in.
(19 mm)
35.625 in.
(905 mm)
60 VARIABLE-SPEED MODEL
FRONT OF MACHINE
PHM631N
Figure 9
20
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
0.75 in.
(19 mm)
0.75 in.
(19 mm)
39.625 in.
(1008 mm)
6.75 in.
(171 mm)
43.75 in.
(1111 mm)
9 in.
(229 mm)
2.25 in.
(57 mm)
52.1875 in.
(1326 mm)
13.625 in.
(346 mm)
46.3125 in.
(1176 mm)
2.25 in.
(57 mm)
39.75 in.
(1010 mm)
13.625 in.
(346 mm)
35.125 in.
(892 mm)
3 in.
(76 mm)
3 in.
(76 mm)
41.125 in.
(1045 mm)
0.75 in.
(19 mm)
80 / 100 MODELS
FRONT OF MACHINE
PHM632N
Figure 10
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
21
Specifications and Dimensions
0.75 in.
(19 mm)
0.75 in.
(19 mm)
46.5 in.
(1181 mm)
7 in.
(178 mm)
10 in.
(254 mm)
48 in.
(1219 mm)
61.5 in.
(1562 mm)
15 in.
(381 mm)
55.47 in.
(1409 mm)
48.94 in.
(1243 mm)
15.25 in.
(387 mm)
23.25 in.
(591 mm)
23.25 in.
(591 mm)
48 in.
(1219 mm)
0.75 in.
(19 mm)
125 MODEL
FRONT OF MACHINE
PHM633N
PHM633N
Figure 11
22
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
56 in.
(1422 mm)
10.375 in.
(264 mm)
48.125 in.
(1223 mm)
51.375 in.
(1305 mm)
47.875 in.
(1216 mm)
10.375 in.
(264 mm)
57.4 in.
(1457 mm)
12.125 in.
(308 mm)
67.1 in.
(1704 mm)
15 in.
(381 mm)
4 in.
(102 mm)
1.5 in.
(38.1 mm)
1.5 in.
(38.1 mm)
47 in.
(1193 mm)
50 in.
(1270 mm)
150 MODEL
FRONT OF MACHINE
PHM778N
PHM778N
Figure 12
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
23
Specifications and Dimensions
Grout Placement
30.125 in.
(765 mm)
17.88 in.
(454 mm)
36 in.
(914 mm)
27.875 in.
(708.025 mm)
36 in.
(914.4 mm)
20 in.
(508 mm)
4.0625 in.
(103 mm) typical
22 in.
(559 mm)
4.0625 in.
(103 mm) typical
4.0625 in.
(103 mm) typical
30.13 in.
35.625 in.(765 mm)
(905 mm)
35 VARIABLE-SPEED MODEL
35 2-SPEED MODEL
PHM547N
PHM547N
PHM574N
PHM574N
35.63 in.
(905 mm)
35.625 in.
(905 mm)
11.9375 in.
(303 mm)
4.0625 in.
(103 mm) typical
35.9375 in.
(913 mm)
12 in.
27.5 in. (305 mm)
(699 mm)
36 in.
(914 mm)
27.5 in.
(699 mm)
4.0625 in.
(103 mm) typical
60 VARIABLE-SPEED MODEL
27.88 in.
(708 mm)
60 2-SPEED MODEL
PHM575N
4.0625 in.
(103 mm) typical
4.0625 in.
(103 mm) typical
PHM548N
PHM548N
PHM575N
41.125 in.
(1044 mm)
41.125 in.
(1044 mm)
14 in.
(356 mm)
43.75 in.
(1111 mm)
4.0625 in.
(103 mm)
typical
17.5 in.
(445 mm)
33 in.
(838 mm)
80 MODEL
43.8125 in.
(1113 mm)
4.0625 in.
(103 mm) typical
PHM576N
PHM576N
20.6875 in.
(526 mm)
33 in.
(838 mm)
100 MODEL
4.0625 in.
(103 mm) typical
4.0625 in.
(103 mm) typical
PHM192N
50 in.
(1270 mm)
48 in.
(1219 mm)
3.25 in.
(83 mm)
34 in.
(863.6 mm)
4.06 in.
(103 mm)
typical
24.31 in.
(617 mm)
10.875 in.
(276 mm)
56 in.
(1422 mm)
48 in.
(219 mm)
39.88 in.
22 in. (1013 mm)
(559 mm)
125 MODEL
4.06 in.
(103 mm)
typical
8 in.
(203.2 mm)
typical
PHM180N
8 in.
(203.2 mm)
typical
150 MODEL
PHM605N
PHM605N
Figure 13
24
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
Gap Setting for Vibration Switch
After the machine has been properly installed, the
vibration switch gap must be verified. To locate the
vibration switch refer to Figures 14, 15 and 16. For
UniLinc models, while the control is displaying the
Inputs Outputs Menu the alarm will sound when the
frame switch is activated. To verify and set the
vibration switch gap use the following procedures:
WARNING
Verify Vibration Switch Gap
(for 35-125 Pound Models):
1. Insert 0.009 inch feeler gauge between the
adjustment bolt and the vibration switch; the
alarm must not activate.
2. Remove the feeler gauge.
3. Insert 0.010 inch feeler gauge (supplied with
machine) between the adjustment bolt and the
vibration switch; the alarm must activate.
4. Remove the feeler gauge.
Only trained personnel should perform this
procedure. Use caution while servicing
machines with covers removed and power
applied.
W700
For UniLinc Models, Navigate to the Inputs
Outputs Menu:
1. From the Cycle Menu press and hold the
,
,
keys to enter the System Menu.
2. Press the arrow keys to highlight the Diagnostic
box.
5. Adjust the vibration switch adjustment bolt if
necessary.
Verify Vibration Switch Gap
(For 150 Pound Models):
1. Insert the 0.010 inch feeler gauge (supplied with
machine) between the adjustment bolt and the
vibration switch.
2. If alarm is active: Slowly loosen adjustment bolt
until the alarm stops.
3. Press the
key to enter the Diagnostic Menu.
3. Very slowly tighten the adjustment bolt until the
alarm activates. The adjustment bolt must be
tightened very slowly to prevent over adjustment.
4. Press the
key to enter the Test Menu.
4. Remove the feeler gauge.
5. Press the arrow keys to highlight the Inputs
Outputs box.
6. Press the
Menu.
key to enter the Inputs Outputs
5. Verify the Frame Switch setting.
To adjust the vibration switch gap on the 150 models,
move the vibration switch by adjusting the jam nuts on
the vibration switch.
For UniLinc models, to return to the Cycle Menu press
BACK key several times until Cycle Menu is
displayed.
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
25
Specifications and Dimensions
35 Pound Model
ADJUSTMENT
BOLT
VIBRATION
SWITCH
PHM794N
PHM794N
Figure 14
26
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
60, 80, 100 and 125 Pound Models
VIBRATION
SWITCH
ADJUSTMENT BOLT
PHM795N
PHM795N
Figure 15
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
27
Specifications and Dimensions
150 Pound Model
VIBRATION SWITCH
PHM716N
PHM716N
Figure 16
28
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
Drain Connection Requirements
DRAIN TROUGH CONFIGURATION
A drain system of adequate capacity is essential to
washer-extractor performance. The water can empty
directly into a sump or floor drain. Figure 17 shows
the drain line configuration and Figure 18 shows the
drain trough configuration.
1
2
DRAIN LINE CONFIGURATION
3
4
1
2
5
6
3
7
PHM621N
PHM789N
1
2
3
Overflow
Vent
Trap (As required by local codes)
NOTE: If a flexible connection is made directly to a
drain system, the drain system must be vented to
prevent an air lock and siphoning.
Figure 17
A flexible connection must be made to a vented drain
system to prevent an air lock and to prevent siphoning.
IMPORTANT: Washer-extractor must be installed
in accordance with all local codes and ordinances.
1
2
3
4
5
6
7
Rear of Machine
Drain Pipe
1 Inch Minimum Air Gap
Steel Grate
Drain Trough
Strainer
Waste Line
Figure 18
Refer to Table 3 for capacity-specific drain
information.
Installation of additional washer-extractors will
require proportionately larger drain connections.
Refer to Table 4.
If proper drain size is not available or practical, a surge
tank is required. A surge tank in conjunction with a
sump pump should be used when gravity drainage is
not possible, such as in below-ground-level
installations.
Before any deviation from specified installation
procedures is attempted, the customer or installer
should contact the distributor.
Increasing the drain hose length, installing elbows, or
causing bends will decrease drain flow rate and
increase drain times, impairing washer-extractor
performance.
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
29
Specifications and Dimensions
IMPORTANT: Do not block the overflow vent
above the drain line.
If water or suds flow from the overflow vent and the
machine has been verified to be operating properly
with proper water levels and correct amount of laundry
chemicals, a drain line may be added to the vent and
routed to a drain trough.
1. Remove the riveted bracket on the rear panel for
access to the overflow vent pipe.
2. Route a drain pipe from the vent pipe to a drain
trough. Drain pipe should be routed straight
across or down and be suspended above drain
trough by at least 3 inches (7.62 cm).
IMPORTANT: Do not route the overflow vent pipe
to a direct drain system.
Drain Information
Specifications
Drain connection size, O.D., in. (mm)
with second drain:
35
60
80
100
125
150
2.375 (60)
3 (76)
3 (76)
3 (76)
3 (76)
3 (77)
1
1
2
2
2
2
35 (132)
64 (242)
120 (454)
120 (454)
140 (530)
140 (530)
5 (142)
6 (170)
9 (255)
11 (311)
13 (368)
13 (368)
Number of drain outlets
Drain flow capacity, gal/min. (l/min.)
3
Recommended drain pit size, ft (l) †
†Sized for one machine using overflow level.
Table 3
Drain Line Sizing
Minimum Drain I.D., in. (mm)
Model
Number of Machines
1
2
3
4
35
3 (76.2)
3 (76.2)
3.5 (88.9)
4 (102)
60
3 (76.2)
4 (102)
6 (152)
6 (152)
80
4 (102)
6 (152)
6 (152)
8 (203)
100
4 (102)
6 (152)
6 (152)
8 (203)
125
4 (102)
6 (152)
6 (152)
8 (203)
150
4 (102)
6 (152)
6 (152)
8 (203)
Table 4
30
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
Water Connection
WARNING
To prevent personal injury, avoid contact
with inlet water temperatures higher than
125° Fahrenheit (51° Celsius) and hot
surfaces.
W748
Maximum water inlet temperature is 190° Fahrenheit
(88° Celsius).
Water Supply Information
Specifications
35
60
80/100
125/150
2
2
2
2
Main fill water inlet size, in. (mm)
3/4 (19)
3/4 (19)
3/4 (19)
1 (25.4)
Number of Spray Rinse water inlets
2
2
2
2
Spray rinse water inlet size, in. (mm)
3/4 (19)
3/4 (19)
3/4 (19)
3/4 (19)
Number of main fill water inlets
Recommended pressure, psi (bar)
Inlet flow capacity (80 psi),
gal/min. (l/min)
30 – 85 (2 – 5.7)
31 (117)
39 (148)
41 (155)
48 (182)
Table 5
Connections should be supplied by hot and cold water
lines of at least the sizes shown in the Water Supply
Line Sizing table. Installation of additional machines
will require proportionately larger water lines. Refer to
Table 6. Flush the water lines before connecting them
to the machine.
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
31
Specifications and Dimensions
To connect water service to machine with rubber
hoses, use the following procedure:
Water Supply Line Sizing
Model
1. Before installing hoses, flush the water system
for at least two minutes.
Number
of Machines
Supply Line Size, in. (mm)
Main
Hot/Cold
1
1 (25)
0.75 (19)
2
1.5 (38)
1 (25)
3
2 (50)
1.25 (32)
4
2 (50)
1.5 (38)
1
1.25 (32)
1 (25)
2
2 (50)
1.25 (32)
3
2 (50)
1.5 (38)
4
2.5 (64)
2 (50)
1
1.25 (32)
1 (25)
2
2 (50)
1.25 (32)
Suitable air cushions should be installed in supply
lines to prevent “hammering.” Refer to Figure 19.
3
2 (50)
1.5 (38)
4
2.5 (64)
2 (50)
For machines labeled with the CE mark, backsiphon
protection devices must be installed previous of all
machine water inlet valves in accordance with
accepted European standards.
1
1.5 (38)
1 (25)
2
2 (50)
1.5 (38)
3
2 (50)
1.5 (38)
4
2.5 (64)
2 (50)
1
2 (50)
1.25 (32)
2
2.5 (64)
2 (50)
3
2.5 (64)
2 (50)
4
2.5 (64)
2.5 (64)
1
2 (50)
1.25 (32)
2
2.5 (64)
2 (50)
3
2.5 (64)
2 (50)
4
2.5 (64)
2.5 (64)
2. Check filters in the washer-extractor’s inlet hoses
for proper fit and cleanliness before connecting.
3. Hang the hoses in a large loop; do not allow them
to kink.
If additional hose lengths are needed, use flexible
hoses with screen filters. Each hose should have a
screen filter installed to keep rust and other foreign
particles out of the water inlet valves.
Pressure of 30 – 85 psi (2 – 5.7 bar) provides best
performance. Although the washer-extractor will
function properly at lower pressures, increased fill
times will occur.
35
60
80
100
1
125
150
Table 6
2
P038I
P038I
1
2
Air Cushions (Risers)
Water Supply Faucets
Figure 19
32
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
Electrical Installation Requirements
IMPORTANT: Electrical ratings are subject to
change. Refer to serial decal for electrical ratings
information specific to your machine.
WARNING
This machine must be installed, adjusted,
and serviced by qualified electrical
maintenance personnel familiar with the
construction and operation of this type of
machinery. They must also be familiar
with the potential hazards involved.
Failure to observe this warning may result
in personal injury and/or equipment
damage, and may void the warranty.
SW004
Electrical connections are made at the rear of the
machine. The machine must be connected to the
proper electrical supply shown on the identification
plate attached to the rear of the machine, using copper
conductors only.
IMPORTANT: Alliance Laundry Systems
warranty does not cover components that fail as a
result of improper input voltage.
Make sure the correct transformer jumper (208 Volt or
240 Volt) is in place. Refer to the “optional” Electrical
Service Connection label located on the back of the
machine near the electrical service input for machine
electrical requirements. Refer to Figure 20.
OPTIONAL ELECTRICAL SERVICE
CONNECTION BASED ON
AVAILABILITY
This unit may be field converted
by a QUALIFIED Electrician to
the following 200-208 Volts
and/or 50 Hertz.
PRIOR TO CONNECTING
ELECTRICAL SERVICE,
COMPLETE THE FOLLOWING
WARNING
F8099701R1
200-208 VAC CONVERSION
VAC: 200-208
PHASE: *
AMPS: *
WIRES & GROUND: *
REC'D BREAKER: *
1. Refer to the Control Transformer area on
the Control Option Diagram.
2. Remove the "240V" Transformer Jumper in
the control box.
3. Replace with "208V" Transformer Jumper
found in the diagram pack.
4. Sign off below.
200-208VAC
Operation
* As indicated on
original serial plate
Transformer Jumper
208V
50Hz CONVERSION
1. Refer to the Control Option Diagram.
2. Remove the wire from the 60Hz tap on drain
valve(s).
3. Connect the wire to the 50Hz Tap on all
drain valves.
Connection Drain Valve(s)
4. Sign off below.
for 50Hz
Operation Only
50Hz
60Hz
on
(SIGN)
(DATE)
50Hz
Operation
N
on
(SIGN)
(DATE)
PHM740N
PHM740N
Dangerous voltages are present in the
electrical control box(es) and at the motor
terminals. Only qualified personnel
familiar with electrical test procedures,
test equipment, and safety precautions
should attempt adjustments and
troubleshooting. Disconnect power from
the machine and wait 3 minutes before
removing the control box cover, and
before attempting any service
procedures.
W702
WARNING
Ensure that a ground wire from a proven
earth ground is connected to the ground
lug near the input power block on this
machine. Without proper grounding,
personal injury from electric shock could
occur and machine malfunctions may be
evident.
SW008
Figure 20
On variable-speed models, the AC inverter drive
requires a clean power supply free from voltage spikes
and surges. A voltage monitor should be used to check
incoming power. The customer’s local power company
may provide such a monitor.
The following conditions require corrective action,
contact the local utility to adjust the voltage. If the
local utility cannot adjust the input voltage, install a
buckboost transformer to lower the input voltage.
Input voltage is above 240V or 480V, phase to ground
voltage exceeds 125% of normal line to line voltage,
or 240V open delta configuration (stinger leg).
Contact the distributor or the manufacturer for
assistance.
On variable-speed models, the AC drive provides
thermal overload protection for the drive motor.
However, a separate three-phase circuit breaker must
be installed for complete electrical overload
protection. This prevents damage to the motor by
disconnecting all legs if one should be lost
accidentally. Check the serial plate on the back of the
washer-extractor for recommended circuit breaker
requirements size.
IMPORTANT: Do NOT use fuses in place of a
circuit breaker.
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
33
Specifications and Dimensions
CAUTION
2
L1
Do not use a phase adder on any variablespeed machine.
L2
SW037
1
The washer-extractor should be connected to an
individual branch circuit not shared with lighting or
other equipment.
SERVICE
GROUND
Refer to serial plate for recommended wire sizes for
runs up to 50 feet (15.24 meters). Use next larger size
for runs of 50 to 100 feet (15.24 to 30.48 meters). Use
2 sizes larger for runs greater than 100 feet (30.48
meters).
CHASIS
3
The connection should be shielded in a liquid-tight or
approved flexible conduit with proper conductors of
correct size installed in accordance with the National
Electric Code or other applicable codes. The
connection must be made by a qualified electrician
using the wiring diagram provided with the washerextractor, or according to accepted European standards
for equipment labeled with the CE mark.
Refer to serial plate for recommended circuit breaker
size and determine wire size based on local code
requirements.
L3
TB1
PHM
MACHINES WITH ELECTRIC HEAT
PHM700N
1
2
3
Grounding Lug: Connect to proven earth
ground
Customer Input Power Terminals
Internal Load Distribution - DO NOT connect
customer power source or load.
Figure 21
1
For personal safety and for proper operation, the
washer-extractor must be grounded in accordance with
state and local codes. If such codes are not available,
grounding must conform with the National Electric
Code, article 250 (current edition) or accepted
European standards for equipment labeled with the CE
mark. The ground connection must be made to a
proven earth ground, not to conduit or water pipes.
Refer to Figure 21 and 22.
SERVICE
GROUND
2
CHASIS
L1
L2
L3
TB1
WARNING
P
MACHINES WITHOUT ELECTRIC HEAT
Electrically heated machines DO NOT
require dual power sources. Do not
connect customer power or customer load
to the Internal Load Distribution terminal
block. Refer to the machine electrical
schematic for details.
W759
PHM721N
1
2
Grounding Lug: Connect to proven earth
ground
Customer Input Power Terminals
Figure 22
Machines can be converted for lower voltage
operation and/or 50 Hz operation. Refer to conversion
label by serial plate for details.
After electrical installation is complete, run the
machine through a test cycle and check for a clockwise
basket rotation during the extract step. If rotation is not
clockwise, disconnect the power from the machine and
have a qualified electrician reverse any 2 motor leads.
34
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
Voltage Designation
*mm2
*AWG
X
200 – 240
50/60
1/3
2/3
12/8
Q
200 – 240
50/60
3
3
8
15
14
2.5
42
50
6
16
R
380 – 480
50/60
3
3
6
15
14
2.5
23
30
10
6
X
200 – 240
50/60
1/3
2/3
15/9
Q
200 – 240
50/60
3
3
9
15
14
2.5
71
80
3
25
R
380 – 480
50/60
3
3
7
15
14
2.5
37
40
8
10
Q
200 – 240
50/60
3
3
9
15
14
2.5
105
110
1
50
R
380 – 480
50/60
3
3
10
15
14
2.5
39
40
8
10
Q
200 – 240
50/60
3
3
10
15
14
2.5
108
110
1
50
R
380 – 480
50/60
3
3
10
15
14
2.5
40
50
6
16
Q
200 – 240
50/60
3
3
9
15
14
2.5
R
380 – 480
50/60
3
3
8
15
14
2.5
Q
200 – 240
50/60
3
3
16
20
12
4
R
380 – 480
50/60
3
3
11
15
14
2.5
20/15 12/14
2.5/2.5
Breaker
Full Load
Amps
15/15 14/14
Electric Heat Machines
*mm2
*AWG
Breaker
Full Load
Amps
150
Wire
125
Phase
100
Cycle
80
Voltage
60
Code
Model
35
Non-Electric Heat
Machines (Standard)
NOT AVAILABLE
4/2.5
NOT AVAILABLE
NOT AVAILABLE
NOT AVAILABLE
* NOTE: Wire sizing listed in this table is based on Article 310, Table 310.16 of the NEC; at 104°F (40°C) ambient
temperature. Follow your local electrical codes. Use only copper conductors, rated for 194ºF (90°C) or higher, type
THHN or better. No more than three current carrying conductors per raceway. Contact your local Authority having
jurisdiction if you have questions. Circuit breakers should be UL 489 listed or better. Single phase circuit breakers
for single phase machines only; three phase circuit breakers for all others.
Table 7
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
35
Specifications and Dimensions
Steam Requirements
(Steam Heat Option Only)
For washer-extractors equipped with optional steam
heat, install piping in accordance with approved
commercial steam practices. Steam requirements are
shown in Table 8.
WARNING
NOTE: Failure to install the supplied steam filter
may void the warranty.
Never touch internal or external steam
pipes, connections, or components. These
surfaces can be extremely hot and will
cause severe burns. The steam must be
turned off and the pipe, connections, and
components allowed to cool before the
pipe can be touched.
SW014
Steam Supply Information
35
60
80
100
125/150
Steam inlet connection,
in. (mm)
1/2
(DN13)
1/2
(DN13)
1/2
(DN13)
1/2
(DN13)
3/4
(DN19)
Number of steam inlets
1
1
1
1
1
Recommended pressure,
psi (bar)
30 – 85
(2.0 – 5.9)
30 – 85
(2.0 – 5.9)
30 – 85
(2.0 – 5.9)
30 – 85
(2.0 – 5.9)
30 – 85
(2.0 – 5.9)
85
(5.9)
85
(5.9)
85
(5.9)
85
(5.9)
85
(5.9)
Maximum pressure,
psi (bar)
Table 8
36
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
Chemical Injection Supply System
Undiluted chemical dripping can damage the washerextractor. Therefore, all chemical supply dispenser
pumps should be mounted below the washer’s
injection point. All dispenser tubing should also run
below the injection point. Loops do not prevent drips
if these instructions are not followed. Failure to follow
these instructions could damage the machine and void
the warranty. Figure 23 shows a typical Chemical
Injection Supply System.
WARNING
Wear eye and hand protection when
handling chemicals; always avoid direct
contact with raw chemicals. Read the
manufacturer’s directions for accidental
contact before handling chemicals.
Ensure an eye-rinse facility and an
emergency shower are within easy reach.
Check at regular intervals for chemical
leaks.
SW016
2
3
1
4
PHM825N
1
2
Injection Point
Loops
3
4
Chemical Dispenser Pump Outlet
PVC Pipe
Figure 23
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
37
Specifications and Dimensions
Connecting External Liquid Supplies to the
Washer-Extractor
1
1. Remove knockout from supply dispenser. Refer
to Figure 24. Plugs are assembled inside the
tubing ring.
2
3
2. Install PG connector in hole with strain reliefs,
included in the seal nut.
4
5
3. Insert tubes through PG base. Do not remove
cups. Tube should extend into the plastic cup,
with the exception of the softener tube, which
should be routed to the outside of the cup.
6
4. Tighten the seal nut to prevent tubing from
escaping the assembly.
5. Before operating machine, confirm lid is
completely closed.
Do not attempt to make chemical injection electrical
connections to points other than those provided
specifically for that purpose by the factory.
PHM559N
PHM559N
1
2
3
4
5
6
Tubing from Pump
Seal Nut
Tubing Ring
Base
Lid
Nut
Figure 24
38
Chemical Injection Supply System
Number of dry supply compartments
5
Number of external liquid supply
connections
8
Liquid supply connection size, in. (mm)
0.625 (15.9)
A bracket, which is located on the left side of the
control module, has been provided for mounting the
external supply controls. This bracket is present only
on models made through 6/30/08. Refer to Figures 3
and 4.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
1
2
3
4
5
6
PHM553N
PHM553N
1
2
3
Strain Relief for Liquid Chemical Supply Lines
Supply Dispenser Lid
Nozzles
4
5
6
Dry Supply Cups
Dry Supply Insert
Polypropylene Supply Dispenser
IMPORTANT: Do not attach anything to nozzles. Air gap must be maintained.
Figure 25
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39
Specifications and Dimensions
External Supplies
For proper communication between the washerextractor and an external chemical supply system, it is
important for the signal power to be connected
properly. The included wiring diagram shows several
different options for safe and correct wiring of this
interface.
The preferred method for connecting the wiring from
the external chemical supply system to the washerextractor is to use the 300mA power of the washerextractor’s 24VAC control transformer, which is
intended strictly for this purpose. Other voltage and
current options are available, but require some wiring
changes and must be provided with an external power
source. Under no circumstances should the highvoltage machine supply connections or source be used
for the communication wiring.
Communication wiring connections, which include a
single row of identified terminal blocks, can be found
under a service panel at the upper back of the machine.
Chemical Injection Using Internal 24VAC
Control Transformer
NOTE: Using the Internal 24VAC 300 Milliamp
Control Transformer is recommended by Alliance
Laundry Systems.
IMPORTANT: DO NOT remove the red jumper
wire from the terminal strip.
There are 3 terminals necessary for this
connection option.
• Terminal “24VAC COM” is used to connect one
side of the internal control transformer to the
external dispenser input signals common.
• The second terminal is used to connect the other
side of the control transformer to the washerextractor output signals common through a red
jumper wire between “24VAC” and “RELAY
COM”. Refer to Figure 26.
IMPORTANT: Do not use the transformer
terminals if an external power supply is used.
3
2
4
5
1
6
= Neutral
= Power
7
PHM821N
1
External Supply Power
5
Red Jumper Wire
2
Internal Control Transformer
6
24VAC Terminal
3
RELAY COM Terminal
7
24VAC COM Terminal
4
External Supply Common
Figure 26
40
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
Chemical injection Using External AC
Power Source
IMPORTANT: The external power must supply
power of 240VAC or less and be protected at 3
Amps or less.
NOTE: An External AC Power Source is NOT
provided by Alliance Laundry Systems.
1. Remove the red jumper wire installed by the
factory between “24VAC”: and “RELAY COM”.
NOTE: Power for external supplies must not be
derived from the high-voltage main power
connection point.
2. Connect one side of the external power to the
“RELAY COM” and the other to the external
dispenser input signals common. Refer to
Figure 27.
3
1
4
2
= Neutral
= Power
5
PHM823N
1
External Supply Power
4
VAC Power Terminal
2
Red Jumper Wire
5
VAC RETURN Terminal
3
External Supply Common
Figure 27
CAUTION
Do not attempt to increase fuse rating or
alter wiring of external chemical supply
terminal strip in such as way that may
conflict with the suggested methods
provided on the Optional External Supply
Wiring Diagram.
W699
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
41
Specifications and Dimensions
External Supply Signals
Wash-cycle signals are provided to the external
chemical supply equipment and a “wait for the next
step” signal can be received from the supply
equipment.
For example, if ES1 is selected the K1 contact will
close and power will be supplied to Supply 1 Signal.
The contact will remain closed for the amount of time
programmed in control. Refer to Figure 28 for Internal
Supply Connection or Figure 29 for External AC
Connection.
3
= Neutral
= Power
1
2
PHM822N
1
ES1 Power supply
2
K1 Contact
3
Supply 1 Signal
Figure 28
42
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8138601
Specifications and Dimensions
3
= Neutral
= Power
1
2
PHM824N
1
ES1 Power supply
2
K1 Contact
3
Supply 1 Signal
Figure 29
F8138601
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
43