Mr. Heater MH15T Operating instructions

Operating Instructions
and Owner’s Manual
Model #
MH15TS
MH30TS
READ INSTRUCTIONS CAREFULLY: Read and follow all instructions. Place instructions in a safe
place for future reference. Do not allow anyone who has not read these instructions to assemble,
light, adjust or operate the heater.
Gas-fired Infra-Red
TANK tOP Heater
Serial Numbers:
ModelNumbers Starting With
MH15TS CL-242105-12001001
Cylinder not included
MH30TS CL-242655-12001001
LANGUAGES
ENGLISH
Pages E1 — E8
SPANISH
Pages S1 — S8
FRENCH
MH15TS
WARNING:
MH30TS
Pages F1 — F8
If the information in this manual is not followed exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
­— Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any
other appliance.
— An LP cylinder not connected for use shall not be stored in the vicinity of this or any other
appliance.
—WHAT TO DO IF YOU SMELL GAS
•Do not try to light appliance.
•Extinguish any open flame.
•Shut off gas to appliance.
— DO NOT LEAVE HEATER UNATTENDED OR IN OPERATION WHILE SLEEPING.
This is an unvented gas-fired portable heater. It uses air (oxygen) from the area in which it is used.
Adequate combustion and ventilation air must be provided. Refer to page 2.
MR. HEATER, INC., 4560 W. 160TH ST., CLEVELAND, OHIO 44135 • 800-251-0001
02/12 Rev 12A 42652
WARNING:
WARNING:
YOUR SAFETY IS IMPORTANT TO YOU AND TO OTHERS,
NOT FOR HOME OR RECREATIONAL VEHICLE USE
GENERAL HAZARD WARNING:
WARNING:
FAILURE TO COMPLY WITH THE PRECAUTIONS AND
INSTRUCTIONS PROVIDED WITH THIS HEATER, CAN
RESULT IN DEATH, SERIOUS BODILY INJURY AND
PROPERTY LOSS OR DAMAGE FROM HAZARDS OF
FIRE, EXPLOSION, BURN, ASPHYXIATION, CARBON
MONOXIDE POISONING, AND/OR ELECTRICAL
SHOCK.
ONLY PERSONS WHO CAN UNDERSTAND AND FOLLOW THE INSTRUCTIONS SHOULD USE OR SERVICE
THIS HEATER.
IF YOU NEED ASSISTANCE OR HEATER INFORMATION SUCH AS AN INSTRUCTIONS MANUAL,
LABELS, ETC. CONTACT THE MANUFACTURER. SO
PLEASE READ THESE INSTRUCTIONS BEFORE YOU
OPERATE THIS HEATER.
FIRE, BURN, INHALATION, AND EXPLOSION HAZARD. KEEP SOLID COMBUSTIBLES, SUCH AS BUILDING MATERIALS, PAPER OR CARDBOARD, A SAFE
Distance AWAY FROM THE HEATER AS RECOMMENDED BY THE INSTRUCTIONS. NEVER USE THE
HEATER IN SPACES WHICH DO OR MAY CONTAIN
VOLATILE OR AIRBORNE COMBUSTIBLES, OR
PRODUCTS SUCH AS GASOLINE, SOLVENTS, PAINT
THINNER, DUST Particles OR UNKNOWN
CHEMICALS.
WARNING:
The State of California requires the following warning:
COMBUSTION BY-PRODUCTS PRODUCED WHEN USING THIS PRODUCT CONTAIN CARBON MONOXIDE,
A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA
TO CAUSE CANCER AND BIRTH DEFECTS (OR OTHER
REPRODUCTIVE HARM).
WARNING:
CARBON MONOXIDE CAN KILL YOU
USING A PORTABLE GAS CAMPING HEATER INSIDE
A TENT, RV, CAMPER, VEHICLE, SHELTER OR OTHER
ENCLOSED AREAS CAN PRODUCE DEADLY CARBON
MONOXIDE
CONTENTS
This product contains chemicals known to the
State of California to cause cancer and birth
defects or other reproductive harm.
The heater is designed and approved for us as, a construction heater and in accordance with ANSI Z83.7-CSA 2.14.
Check with your local fire safety authority if you have any
questions about applications.
WARNINGS...................................................................................2
ASSEMBLY AND HOOKUP INFORMATION.....................................3
ODOR FADE WARNING.................................................................4
Other standards govern the use of fuel gases and heatproducing products and specific applications. Your local
authority can advise you about these standards.
GENERAL INFORMATION..............................................................4
FOR SAFE OPERATION..................................................................5
VENTILATION...............................................................................5
MINIMUM CLEARANCE FROM COMBUSTIBLE MATERIALS...........5
LIGHTING INSTRUCTIONS.............................................................6
SHUTDOWN AND STORAGE INSTRUCTIONS.................................6
PARTS LIST....................................................................................7
WARRANTY..................................................................................8
INSTRUCTIONS FOR ORDERING PARTS..........................................8
Mr. Heater | Gas-Fired Infra-Red Tank Top Heater
E-2
Operating Instructions and Owner’s Manual
ASSEMBLY AND HOOK-UP INFORMATION
1. Heater model MH15TS and MH30TS are packaged
complete. Propane cylinders (tanks) are not included
with heater model.
2. Remove heater from carton.
3.Use only vapor withdrawal LP gas cylinders constructed
for use with propane only (HD-5) and marked in accordance with the specifications for LP gas cylinders of the
U.S. Department of Transportation (DOT SPEC. 39).
4.This heater must be used only with a vapor withdrawal
LP gas bulk tank equipped with a standard POL valve
– do not use this heater on bulk tanks greater than 20
pounds LPG capacity (50 pounds water capacity).
5a.MH30TS Dual Burner Model (see Figure 1.)
•The tank collar bracket must be assembled before
the heater can be attached to the propane tank.
• Remove screws holding Piezo Igniter bracket to
manifold center plate and retain for later use.
• Align bolt holes in tank collar bracket with bolt
holes in center plate on manifold such that the
heater is facing outward once attached to cylinder
collar.
• Attached with screws removed above, making sure
that Piezo Igniter bracket is between tank collar
bracket and manifold center plate.
• Place heater onto tank with tank collar bracket over
tank collar. Mounting bolt knob should be positioned to the outside of tank collar.
• Firmly secure to tank by hand-tightening mounting
bolt knob. Do not overtighten.
• Make sure heater regulator is in the “OFF” position.
•Insert regulator’s connector into tank’s valve and
turn left (counterclock-wise) with hand as much as
possible. Do not overtighten.
5b.MH15TS Single Burner Model (See Figure 2.)
• Be sure heater is facing away from tank.
•Insert regulator connector into tank valve outlet
fitting and turn left (counterclock-wise) until fully
tightened. Do not overtighten. (See Figure 2a)
• Place heater support around venturi and slide clip
ends onto propane cylinder collar. Use 1/4”-20 x
35mm screw and wing nut to secure heater support onto venturi tube. (See Figure 2b)
Figure 2a.
Figure 2b.
6.Operate only on a stable, level surface.
7.Open propane tank valve slowly.
8. Check all fittings for leaks. Apply a 50/50 mixture of
liquid soap and water to all joints. Bubbles forming
indicate a leaking connection. Correct all leaks before
proceeding.
WARNING
Never touch heater while in operation to avoid injury.
Move heater by grasping the propane cylinder carefully.
9. The heater should be inspected before each use and at
least annually by a qualified service person.
10. The hose assembly shall be visually inspected prior to
use of heater. If it is evident there is excessive abrasion
or wear, or the hose is cut, it must be replaced prior to
the heater being put into operation. Replacement hose
assembly shall be Mr. Heater hose assembly as listed in
the parts list.
11. Minimum inlet gas pressure is 20 psi.
12. Maximum inlet gas pressure is 120 psi (equivalent to an
ambient temperature of 75°F (24°C)).
Figure 1.
Mr. Heater | Gas-Fired Infra-Red Tank Top Heater
E-3
Operating Instructions and Owner’s Manual
ODOR FADE WARNING
•Smoking can decrease your ability to smell. Being around an
odor for a period of time can affect your sensitivity to that
particular odor. Odors present in animal confinement buildings
can mask fuel gas odor.
•The odorant in propane (LP) gas and natural gas is
colorless and the intensity of its odor can fade under
some circumstances.
•If there is an underground leak, the movement of gas through
the soil can filter the odorant.
•Propane (LP) gas odor may differ in intensity at different levels.
Since Propane (LP) gas is heavier than air, there may be more
odor at lower levels.
•Always be sensitive to the slightest gas odor. If you
continue to detect any gas odor, no matter how small, treat
it as a serious leak. Immediately go into action as discussed
previously.
WARNING
Asphyxiation Hazard
Do not use this heater for heating human living quarters.
• Do not use in unventilated areas.
•The flow of combustion and ventilation air must not be obstructed.
• Proper ventilation air must be provided to support the combustion air requirements of the heater being used.
• Refer to the specification section of the heater’s manual, heater dataplate, or contact the factory to determine combustion air ventilation requirements of the heater.
•Lack of proper ventilation air will lead to improper combustion.
•Improper combustion can lead to carbon monoxide poisoning leading to serious injury or death. Symptom of carbon monoxide poisoning can include headaches, dizziness and difficulty in breathing.
•
ATTENTION ‑ CRITICAL POINTS TO
REMEMBER!
•Propane (LP) gas has a distinctive odor. Learn to recognize
these odors. (Reference Fuel Gas Odor and Odor Fading
sections to the left and above).
•Even if you are not property trained in the service and repair
of the heater, ALWAYS be consciously aware of the odors of
propane (LP) gas and natural gas.
•If you have not been properly trained in repair and service of
propane (LP) gas then do not attempt to light heater, perform
service or repairs, or make any adjustments to the heater on
the propane (LP) gas fuel system.
•A periodic sniff test around the heater or at the heater’s
joints; i.e. hose, connections, etc., is a good safety practice
under any conditions. If you smell even a small amount of gas,
CONTACT YOUR FUEL GAS SUPPLIER IMMEDIATELY. DO NOT
WAIT!
FUEL GAS ODOR
LP gas and natural gas have man‑made odorants added
specifically for detection of fuel gas leaks.
If a gas leak occurs you should be able to smell the fuel
gas. Since Propane (LP) is heavier than air you should smell
for the gas odor low to the floor. ANY GAS ODOR IS YOUR
SIGNAL TO GO INTO IMMEDIATE ACTION!
•Do not take any action that could ignite the fuel gas. Do not
operate any electrical switches. Do not pull any power supply
or extension cords. Do not light matches or any other source
of flame. Do not use your telephone.
•Get everyone out of the building and away from the area
immediately.
•Close all propane (LP) gas tank or cylinder fuel supply valves,
or the main fuel supply valve located at the meter if you use
natural gas.
•Propane (LP) gas is heavier than air and may settle in low
areas. When you have reason to suspect a propane leak, keep
out of all low areas.
•Use your neighbor’s phone and call your fuel gas supplier and
your fire department. Do not re‑enter the building or area.
•Stay out of the building and away from the area until declared
safe by the firefighters and your fuel gas supplier.
•FINALLY, let the fuel gas service person and the firefighters
check for escaped gas. Have them air out the building and
area before you return. Properly trained service people must
repair any leaks, check for further leakages, and then relight
the appliance for you.
GENERAL INFORMATION
A. The MH15TS and the MH30TS are high pressure propane
appliances and are designed to be connected to a bulk
propane tank.
B. These heaters are equipped with an automatic Safety Shutoff
Valve. The gas flow will automatically stop if the heater fails to
operate for any reason.
C. Maximum safety and convenience have been built into the
Hi-Med-Lo-Off Control Valve/Regulator. The following table lists
the approximate BTU’s consumed and the operating hours you
can reasonably expect from bulk propane cylinders.
D. These heaters are for temporary heating of buildings under
construction, alterations, or repair.
Model
MH15TS
ODOR FADING ‑ NO ODOR DETECTED
Mr. Heater | Gas-Fired Infra-Red Tank Top Heater
Hours
w/20lb.
Tank
BTU Input
Hours
w/ 20lb.
Tank
Hi
15,000
28
30,000
14
Med
12,000
36
24,000
18
Lo
10,000
43
10,000
43
Valve Position
•Some people cannot smell well. Some people cannot smell
the odor of the man‑made chemical added to propane (LP) or
natural gas. You must determine if you can smell the odorant
in these fuel gases.
•Learn to recognize the odor of propane (LP) gas and natural
gas. Local propane (LP) gas dealers will be more than happy
to give you a scratch and sniff pamphlet. Use it to become
familiar with the fuel gas odor.
MH30TS
BTU
Input
Figure 3.
E. MH15TS and MH30TS are equipped with “Sparklite” igniters
for convenient heater lite-off.
E-4
Operating Instructions and Owner’s Manual
FOR SAFE OPERATION
L. DO NOT TRANSPORT OR MOVE APPLIANCE WHILE
IN OPERATION. FOLLOW SHUTDOWN AND STORAGE
INSTRUCTIONS TO TRANSPORT OR MOVE THIS
APPLIANCE.
A. READ INSTRUCTIONS CAREFULLY: Read and adhere to
these instructions. Do not allow anyone who has not read the
instructions to assemble, light, adjust or operate the heater.
VENTILATION
WARNING
A. WARNING: This heater is an unvented appliance and
MUST be used ONLY in a well ventilated area. NEVER
attempt to operate the heater inside any vehicle, camper or
enclosure.
B. FOR Non-residential indoor and outdoor use.
Any combustion process requires and consumes oxygen, and
will produce carbon monoxide. THIS HEATER MUST BE
USED WITH ADEQUATE VENTILATION. Do not use inside
a house, camper, tent or any type of unvented or a tightly
enclosed area.
C. WARNING: Provide ample ventilation. This heater consumes
air (oxygen). Do not use this heater in unventilated structures
to avoid endangering your life. Provide additional ventilation
for any additional fuel-burning appliances and additional
occupants.
D. Flow of combustion and ventilation air must not be obstructed.
KEEP THE HEATER OUT OF THE REACH OF CHILDREN
B. Use only in accordance with local codes or, in the absence of
local codes, with the standard for the Storage and handling
of Liquefied Petroleum Gases ANSI/NFPA 58 and CSA B 149.1,
Natural Gas and Propane Installation Code.
C.PROPANE IS VERY FLAMMABLE: In the event of a leak,
propane will accumulate and the possibility of a fire is
present. Propane gas is scented and its strong odor is readily
detectable. Never strike a match or bring any flame or create
an electric spark in an enclosure when you smell propane gas.
Ventilate the area thoroughly, move the heater outside, find
and correct the source of the leak before attempting to light
any appliance. If you are unsure of these instructions evacuate
immediately and call for help.
D. GAS LEAKAGE: If the leak cannot be corrected do not
tamper with the heater, follow the shut down instructions and
return the heater to the dealer or address given on last page.
MINIMUM CLEARANCE FROM
COMBUSTIBLE MATERIALS
A. When operating, the heater surfaces are extremely hot. Keep
sleeping bags, clothing, and all combustible materials clear of
the heater by at least the distances shown in figure 4.
WARNING
DO NOT USE THIS HEATER ON BULK TANKS OF GREATER
BTU/HR. Rating
CAPACITY THAN 20 POUNDS LPG (50 POUNDS WATER
CAPACITY).
E. LEAK DETECTION: Before each use of the heater check all
fittings and connections with a soap solution to be sure there
are no leaks. NEVER, NEVER USE ANY FLAME FOR LEAK TEST.
F. CONNECTING HEATER TO PROPANE CYLINDER: Always
connect the heater to the bulk cylinder in the outdoors or in
a well ventilated area. NEVER connect this heater to a cylinder
near an open flame.
G. USE OF HEATER: Always operate the heater with the propane
cylinder in an upright position on a level noncombustible
surface. NEVER place the cylinder on its side when operating
the heater.
H. ATTEND HEATER: Do not leave heater unattended while it is
in operation.
I. ALWAYS LIGHT HEATER WITH MATCH OR “SPARKLITE”
IGNITER: NEVER attempt to light the heater with a spark
lighter.
J. DO NOT TAMPER: Should the heater not perform properly,
such as little or no heat when operating in the “Hi” position,
or for any other reason, DO NOT ATTEMPT TO REPAIR OR
TAMPER with the heater. Any tampering could make the
use of the heater unsafe and dangerous. Return the heater
to the dealer or the address given on last page for repair or
replacement.
K. FOR STORAGE: The heater Hi-Med-Lo-Off regulating valve
should always be turned to “off” when the heater is not in
use. Allow at least 15 minutes for cooling before handling and
storing. Detach propane cylinder from heater before storing.
DO NOT store propane cylinders indoors or near open flame
or heat.
Mr. Heater | Gas-Fired Infra-Red Tank Top Heater
Normal
Operating
Procedure
Clearances to Combustibles
From C.L.
OF HTR.
TO FLOOR
FRONT
SIDES
REAR
CEILING
15,000
Vertical
24”
30”
30”
30”
30”
30,000
Vertical
24”
30”
30”
30”
36”
Model
no.
Gas
Propane
MH15TS
MH30TS
Figure 4.
B. WARNING: To avoid injury or property damage never allow
clothing, tents or other combustible materials within 30” of
the face of the heater. This heater must be located at least 24”
above the floor level when in use. Never operate the heater
when sleeping.
C. WARNING: Never direct the heat output of this heater toward
any propane tank within 20 feet.
E-5
Operating Instructions and Owner’s Manual
LIGHTING INSTRUCTIONS
SHUTDOWN AND STORAGE
INSTRUCTIONS
A. Before attempting to light the heater, check all fittings and
connections with a soap solution. NEVER USE A MATCH TO
CHECK FOR LEAKS. Should a gas leak occur, do not attempt
to repair or use heater. Return the heater to your dealer or the
address given on back page.
B. Fuel – This heater must be used only with a vapor withdrawal
LP gas bulk cylinder. THE BULK TANK MUST BE EQUIPPED
WITH A STANDARD POL VALVE.
A. The bulk propane tank “on-off” valve should ALWAYS be
completely turned “OFF” when the heater is not in use.
B. When shutting off the heater, turn the regulator knob on the
heater to “OFF” (clockwise).
C. CAUTION: After turning unit off, heater will remain extremely
hot. Allow at least 15 minutes for cooling before handling and
storing. Detach heater from bulk tank before handling and
storage. REMEMBER – POL fitting is a left-hand thread.
D. HEATER STORAGE: Indoor storage of the heater is
permissible only if the cylinder is disconnected and removed
from the heater. Cylinders must be stored outdoors out of the
reach of children and must not be stored in a building, garage
or any other enclosed area. Store cylinders only in accordance
with the Standard for the Storage and Handling of Liquefied
Petroleum Gases ANSI/NFPA 58 and CSA B149.1, Natural Gas
and Petroleum Installation Code.
E. See page 7 for spare parts list.
WARNING
USE HD.5 PROPANE GAS ONLY. DO NOT USE ANY OTHER
TYPE FUEL. SEE YOUR PROPANE DEALER IF YOU HAVE ANY
QUESTIONS REGARDING FUEL.
C. Turn the heater’s “Hi-Med-Lo-Off” regulator knob to “Med”
(counterclockwise).
D. To light the MH15TS, press the Safety Shutoff Valve. While
holding the Safety Shutoff Valve button, immediately press the
“Sparklite” ignition button (repeat until heater lights). After
the heater is lit, continue to hold the Safety Shutoff Valve for
30 seconds, then release the button.
OPTIONAL LIGHTING: To light heater, place a lit match inside
hole on rear reflector marked “light here”. (See Figure 5) THEN
push in valve button on Safety Shutoff Valve. After the heater
is lit, continue to hold valve button in for 30 seconds, then
release the button slowly. CAUTION: DO NOT PUSH IN VALVE
BUTTON BEFORE INSERTING LIT MATCH. NEVER STAND IN
FRONT OF HEATER WHILE LIGHTING. REPEAT STEP “D” FOR
EACH BURNER
E. To light a burner, MH30TS Model, push in valve button on
Safety Shutoff Valve and at the same time push down on
“Sparklite” Igniter button. Repeat push down of “Sparklite”
Igniter button until burner ignites After burner is lit, continue
to hold valve button in for 30 second, then release the button
slowly. Repeat step “E” for each burner of the MH30TS Heater.
(See Figure 6)
F. If burner does not light within 30 seconds, turn the heater’s
regulator knob to “off” (clockwise) and allow at least five
minutes for gas to dissipate before attempting to relight.
G. NOTE: Should the orifice become clogged as indicated by low
volume of gas when operating on “Hi” with a full cylinder,
or should the heater fail to operate properly for any reason,
return the heater to the dealer or the address given on back
page for repair or replacement. DO NOT ATTEMPT TO REPAIR
OR TAMPER WITH HEATER.
H. Adjust heat output by turning knob to desired position.
I. DO NOT USE THIS HEATER FOR COOKING.
Maintenance
A. Remove thermocouple (3) retaining bracket screw from back of
burner assembly (2). Remove bracket.
B.Note position of thermocouple (3) in retaining tabs on the
back of the Burner assembly (2). Remove the thermocouple.
C. Remove wing bolt (18) and fiber washer (19) that attached the
safety shut-off (6) to the burner Assembly (2).
D. Slide the safety shut-off (6) from burner assembly (2).
E. Remove burner orifice (20) from the safety shut-off (6).
F. Clean burner orifice with compressed air (80 psi max).
G. Direct compressed are through the burner(2) venturi tube
toward the burner plenum so that dust collected on the grid
screen will be blown outward. Keep face away from the grid
screen.
H. Reassemble heater in reverse order of disassembly.
Model: MH15TS
Figure 5
Figure 6
Model: MH30TS
Mr. Heater | Gas-Fired Infra-Red Tank Top Heater
E-6
Operating Instructions and Owner’s Manual
Mr. Heater • Gas-Fired Tank Top Portable Heater • Model #MH15TS and MH30TS
13
20
21
22
23
Model: MH15TS
Model: MH30TS
MH15TS
Item #
Description
1
2
3
4
MH30TS
Number
Qty
Number
Qty
Regulator Assembly
17314
1
17314
1
Burner Assembly
42113
1
42110
2
Guard Assembly
17413
1
17413
2
Rear Guard Assembly
17418
1
17418
2
5
Safety Shut-Off Valve
17416
1
17416
2
6
Manifold
--
--
42666
1
7
Tank Collar Bracket
--
--
42618
1
8
Mounting Bolt Knob
--
--
17415
1
9
Gas Hose
--
--
17411
1
10
Burner Assembly with Guards
17419
1
17419
2
11
Label, Model/Opr. Instr.
42103
1
42656
1
12
Support Wireframe
17353
1
--
--
13
Tip Switch
42116
1
42116
2
14
Thermocouple/Tip Switch Wire Assembly
17349
1
17349
2
15
Wing Bolt
17342
1
17342
2
16
Fiber Washer
17341
1
17341
2
17
Orifice, Not sold separately
--
1
--
2
18
Wing Nut
17324
1
--
--
19
Bolt
17323
1
--
--
20
Sparklite Igniter Mounting Bracket
--
--
73234
1
21
Sparklite Igniter
73235
1
73235
1
22
Spark Electrode / Bottom
42136
1
42136
1
23
Spark Electrode / Side
--
--
42614
1
Mr. Heater | Gas-Fired Infra-Red Tank Top Heater
E-7
Operating Instructions and Owner’s Manual
Operating Instructions
and Owner’s Manual
Gas-fired Infra-Red
Tank Top Heater
Cylinder not included
Serial Numbers:
ModelNumbers Starting With
MH15TS CL-242105-12001001
MH30TS CL-242655-12001001
Model #
MH15TS
MH30TS
WARNING:
USE ONLY MANUFACTURER’S REPLACEMENT PARTS. USE OF ANY OTHER PARTS
COULD CAUSE INJURY OR DEATH. REPLACEMENT PARTS ARE ONLY AVAILABLE
DIRECT FROM THE FACTORY AND MUST BE INSTALLED BY A QUALIFIED SERVICE
AGENCY.
PARTS ORDERING INFORMATION:
PURCHASING: Accessories may be purchased at any Mr. Heater Products local dealer
or direct from the factory
FOR INFORMATION REGARDING SERVICE
Please call Toll-Free 800-251-0001
www.mrheater.com
Our office hours are 8:30 AM – 5:00 PM, EST, Monday through Friday.
Please include the model number, date of purchase, and description of problem in all
communication.
LIMITED WARRANTY
Mr. Heater, Inc. warrants its heaters and accessories to be free from defects in material
and workmanship for a period of 1 year from date of purchase. Mr. Heater, Inc. will
repair or replace this product free of charge if it has been proven to be defective within
the 1-year period, and is returned at customer expense with proof of purchase to Mr.
Heater, Inc. within the warranty period.
Mr. Heater, Inc. reserves the right to make changes at any time, without notice or
obligation, in colors, specifications, accessories, materials and models.
PRODUCT REGISTRATION: Thank you for your purchase.
Please log in to http://www.egiregistration.com to register your product.
Mr. Heater, Inc., 4560 W. 160TH ST., CLEVELAND, OHIO 44135 • 800-251-0001
Mr. Heater are registered trademarks of Mr. Heater, Inc.
© 2009, Mr. Heater, Inc. All rights reserved
Mr. Heater | Gas-Fired Infra-Red Tank Top Heater
E-8
Operating Instructions and Owner’s Manual