Monitor Audio | EN 50020 | Specifications | Monitor Audio EN 50020 Specifications

Contents
Important information
1
Introduction
2
Speaker Location
2
Fine Tuning & Calibration
2
Timbre Matching Guide
2
Technology
3
In-Ceiling & In-Wall features
4
In-Ceiling installation
5-6
In-Wall installation
7-8
Setting Up In-Ceiling Loudspeakers
9
Fine tuning of In-Ceiling & In-Wall Loudspeakers
9
In-Ceiling Technical Specifications
10
In-Wall Technical Specifications
11
Guarantee & Service
12
Declaration of Conformity
12
Multi-lingual safety warnings
(German, Italian, Spanish and French)
13-14
IMPORTANT INFORMATION
The CP Series In-Ceiling and In-Wall loudspeakers will provide long term satisfaction in terms of
sound quality and reliability provided they are installed correctly, according to the instructions and
conditions contained in this manual. Please read this installation guide carefully before proceeding.
We assume the installer is trained and skilled in the correct and safe use of hand and power tools and
has a working knowledge of local building and fire regulations/codes as well as experience of the
conditions/services behind walls and ceilings into which these speakers will be installed. IF IN DOUBT
ABOUT YOUR ABILITY TO INSTALL THESE PRODUCTS SAFELY AND CORRECTLY PLEASE
CONTACT YOUR LOCAL AUTHORISED MONITOR AUDIO DEALER OR CUSTOM INSTALLER.
WARNINGS:
 A minimum depth of 190mm (7½ Inches) is required for the BR, RS & GS In-Ceiling back box to fit into
recess. The BR, RS & GS In-Wall requires 101mm (4 Inches). The Radius In-Ceiling and Stereo In7
Ceiling require a minimum depth of 159mm (6 ¼ Inches) and the Radius In-Wall requires 98mm (3 /8
Inches)
 The fixing clamps require a minimum of 25mm (1 Inch) of surface area around the cut-out hole to ensure
a secure fixing!
3
 The fixing clamps will operate on ceilings or walls with a minimum thickness of 9mm ( /8 Inches) to a
maximum depth of 32mm (1¼Inches)
 Do not attempt to fix these speakers to your ceiling or wall if you are unsure of your ability to provide a
secure and safe fixing. IF IN DOUBT CONTACT YOUR LOCAL AUTHORISED MONITOR AUDIO
DEALER OR CUSTOM INSTALLER.
 Ensure that there are no water pipes, air ducts or electricity cables running immediately behind the cut
out area!
 Please work from secure steps or scaffold and avoid trailing wires for your safety and those around you.
 Always turn off the amplifier or other devices in the system when connecting these speakers
1
Introduction
Congratulations and thank you for purchasing this high performance Monitor Audio CP Series loudspeaker.
In over thirty years, Monitor Audio has become synonymous with high performance, technical excellence, innovation
and superior aesthetic design. Our heritage of investment in high-end metal driver and cabinet technology is
powerfully expressed by a versatile award-winning range of speakers, which set class-leading standards of sonic
excellence and aesthetic appeal. Our now legendary attention to detail ensures that we build the complete
loudspeaker for every application, as truthful and transparent as possible.
We invest as much care, expertise and research in the smallest loudspeaker as we do in the grandest. In every case,
the materials and technology we apply are broadly similar, endowing each speaker with the same accurate tonal
signature. Irrespective of architecture ori
nt
er
i
ordes
i
gn,Moni
t
orAudi
o’
sr
angegi
vesyout
hef
r
eedom t
os
uppl
yhi
gh
quality sound from a versatile mix of floor, stand, wall and flush-mounted speakers. With Monitor Audio, a home can
look and sound beautiful.
Speaker Location
We strongly recommend that these speakers be installed professionally so that positioning and fine-tuning can be
successfully undertaken using sound measuring equipment, coupled with room layout experience and technical
knowledge.
Your CP series In-Ceiling and In-Wall loudspeakers installed in your home theatre can be used as surround speakers
in conjunction with freestanding speakers. If you are unsure about where to locate your surround speakers for
optimum performance, please contact your Monitor Audio Dealer for advice.
When mounting your speakers in the ceiling, locate the speakers 0.6-2m (2 to 6 feet) behind your listening position.
The speakers should be installed 2 to 3m (6 to 10 feet) apart centre to centre.
Fine Tuning & Calibration
Your amplifier or A/V receiver manual will contain information and detailed instruction on fine tuning/calibrating your
system so that the correct balance is achieved between the various speakers. It may be necessary to adjust the CP
speakers as described in pages 7.
Timbre Matching Guide
Illustrating the perfect blend of custom installation & hi-fi speakers for optimal performance.
2
Technology
®
MMP Mk2
Anadvancei
ndr
i
vert
echnol
ogydevel
opedf
r
om Moni
t
orAudi
o’
sor
i
gi
nalMet
alMat
r
i
xPol
y
merconematerial. It uses
a high-pressure injection moulding process to achieve different thicknesses at critical points of the cone geometry.
MMP® Mk2 provides better stiffness, consistency and tighter production tolerances resulting in superior sonic
performance.
®
C-CAM Tweeters
Advanced software simulation has allowed us to optimise the tweeter design, bringing higher sensitivity and a wider
bandwi
dt
ht
or
evealt
hef
i
nes
thi
ghf
r
equencydet
ai
lal
lt
hewayupt
o30kHz.We’
vedevel
opedas
ophi
s
t
i
cat
ednew
chamber with graduated damping, which controls undesirable resonances for a smoother more accurate response.
®
C-CAM drivers
Developed over many years, C-CAM is used as a cone material for all high frequency drivers, and deployed for midrange and bass drivers in our mid-market and top-of-the-range CI and hi-fi speakers. Created originally by aerospace
engineers for jet-engine blades, Ceramic-Coated Aluminium/Magnesium exhibits ideal acoustic properties, being
extremely strong but very light in weight. Conventional cone materials are liable to flex in operation, producing a
significant level of audible distortion.
RST
®
Our most refined technology, the RST cone surface is patterned with either concentric dimples or radial ridges, which
further reduces mass, increases stiffness and eliminates the bending associated with conventional metal cone
designs. The result is a smoother, more agile response, better control of break-up and a wider dynamic range. Not
only is RST employed by the Gold Signature range of hi-fi loudspeakers, but also the GS-CP in-ceiling and in-wall
models.
CP
No sound installation is ever the same. CP stands for Controlled Performance, because each CP in-ceiling or in-wall
product is fitted with its own rigid mineral filled enclosure allowing the acoustics to be optimised every time. This
ensures that its exceptional sound remains consistent wherever it is fitted.
High Frequency Switching [H.F]
Factory set to 0dB, this offers a sonic balance as the designer intended. However in environments with a high degree
of soft furnishings it may be desirable to lift the H.F level to the +3dB setting to achieve a neutral sonic balance. In a
minimalist environment it maybe necessary to drop the H.F level to -3dB position.
Mid Frequency Switching [M.F]
Factory set to 0dB, this offers a sonic balance as the designer intended. However in environments with a high degree
of soft furnishings it may be desirable to lift the M.F level to the +3dB setting to achieve a neutral sonic balance. In a
minimalist environment it maybe necessary to drop the M.F level to -3dB position.
3
CP Gold Signature Features
®
CP GS speakers utilise our C-CAM (Ceramic Coated Aluminium Magnesium alloy) cone, featuring Rigid Surface
®
Technology (RST ). I
mpr
es
s
i
onsont
hecone’
ss
ur
f
ace are designed to eliminate bending, increase stiffness and
lower mass when compared with conventional cone driver designs. The result is a much faster response, offering
music reproduction that is closer to the original performance. A rigid die-cast metal chassis design features a vented
rear section and provides extremely low distortion with typically higher output levels. The in-wall model uses the
exact same tweeter as that found in the regular stand mount and floor standing GS loudspeakers. Both the in-ceiling
and in-wall models extend all the way up to 30KHz.
Additional high frequency and mid-range frequency controls allow the user to set-up the system precisely to obtain
optimum performance within the listening environment. This inherent flexibility makes the CP GS speakers suitable for
a wider range of demanding applications than that offered by their competitors. They pr
omi
s
eat
r
ul
y‘
hi
gh-end’
performance from a custom fit, discreetly installed speaker system.
CP Silver RS Features
Our C-CAM® cone profiles and rubber surrounds maximise the potential of the driver mechanism. The new surrounds
allow greater cone excursions with lower distortion and improved frequency response linearity. The flush cone edge
provides a very smooth response and a natural, accurate sound. The Silver RS CP pivoting tweeter (In-Ceiling only)
®
i
sbasedonMoni
t
orAudi
o’
sf
amous25mm gol
dC-CAM dome. Improvements to the surround and motor system
have extended the frequency response to 30KHz, so that it is ready to exploit new wide bandwidth digital audio
formats such as SACD and DVD-A.
An additional high frequency control offers a fine-tuning option to allow the user to set-up the system precisely and
obtain optimum performance within the listening environment. This additional flexibility makes the Silver RS CP InCeiling and In-Wall speakers suitable for a wider range of demanding residential and commercial applications.
CP Bronze Reference Features
®
The Bronze Reference drive unit, (MMP II) offers an advanced driver technol
ogydevel
opedf
r
om Moni
t
orAudi
o’
s
®
original Metal Matrix Polymer (MMP ) cone material and uses a high-pressure injection moulding process to achieve
®
different thickness at critical points in the cone geometry. MMP II provides better stiffness and consistency and
tighter production tolerances resulting in superior sonic performance. The new bass-mid chassis design has a vented
rear section that reduces thermal power compression to deliver increased dynamic range and higher sound pressure
levels. This venting also lowers distortion by balancing the pressure within the voice-coil motor system. It means
clean, crisp bass and an even clearer mid-range performance.
®
High frequency performance has been improved by the evolution of the C-CAM tweeter. The new tweeter utilises a
pivoting action (In-Ceiling only) to provide optimum imaging and flexible set-up options. The bespoke crossover uses
high-grade polypropylene film capacitors, and low distortion inductors
CP Radius Features
Driver technology refined to del
i
vert
he unpar
al
l
el
ed s
oni
cper
f
or
manc
e ofMoni
t
orAudi
o’
sawar
d-winning ultracompact Radius loudspeakers has been applied to its successful Controlled Performance (CP) in-wall/in-ceiling
designs to render a completely new flush-mounting loudspeaker range for the most discrete installations.
®
The in-wall and in-ceiling models utilise a pivoting 20mm C-CAM Gold Dome tweeter, derived from the remarkable
Radius R45 hi-fi monitor - the smallest speaker Monitor Audio has ever made. Its pivoting action allows for the critical
high frequencies (to 25kHz) to be directed toward the listening position for the most accurate imaging. Radius CP
delivers added installation versatility by providing this feature from in-wall as well as in-ceiling locations. The
®
innovative in-ceiling stereo design uses dual fixed C-CAM (Ceramic Coated Aluminium Magnesium) domes fed
independently with stereo left/right signals. Bass and mid-r
angef
r
equenci
esar
eaccur
at
el
yr
epr
oduced bya5”
®
version of the acclaimed Radius MMP Mk2 driver.
4
Installation –In-Ceiling Units
The CP Series In-Ceiling loudspeakers will provide long term satisfaction in terms of sound quality and reliability
provided they are installed correctly, according to the instructions and conditions contained in this manual. Please
read this installation guide carefully before proceeding. We assume the installer is trained and skilled in the correct
and safe use of hand and power tools, and has a working knowledge of local building and fire regulations/codes as
well as experience of the conditions/services behind walls and ceilings into which these speakers will be installed. IF
IN DOUBT ABOUT YOUR ABILITY TO INSTALL THESE PRODUCTS SAFELY AND CORRECTLY PLEASE CONTACT YOUR
LOCAL AUTHORISED MONITOR AUDIO DEALER OR CUSTOM INSTALLER.
NOW AVAILABLE: Pre-construction brackets. These are for use when installing any CP product before the
plaster board/ rock wall, is fitted. They show the location of the speakers to the builder and give them a solid
secure edge to cut around.
Parts List
PLEASE CHECK YOU HAVE THE FOLLOWING ITEMS IN THIS KIT BEFORE PROCEEDING:






1 x Complete speaker & tweeter assembly fitted to back box.
1 x Grille (which can be painted).
1 x Mounting cut out template (in packaging).
1 x Plastic paint mask (for covering the baffle while painting the frame)
1 x Self adhesive grille membrane (to be attached to the inside the grille after it has been painted).
2 x Spare baffle fixing screws plus guarantee card in this manual.
WARNINGS:
 A minimum depth of 190mm (7½ Inches) is required for the back box on the BR, RS & GS In-Ceiling products
to fit into recess. The Radius In-Ceiling Products require 159mm (6 ¼ Inches).
 The fixing clamps require a minimum of 25mm (1 Inch) of surface area around the cutout hole to ensure a
secure fixing!
 The fixing clamps will operate on ceilings with a minimum thickness of 9mm (3/8 Inches) to a maximum depth
of 32mm (1¼ Inches).
 Do not attempt to fix these speakers to your ceiling if you are unsure of your ability to provide a secure and
safe fixing. IF IN DOUBT CONTACT YOUR LOCAL AUTHORISED MONITOR AUDIO DEALER.
 Ensure that there are no water pipes, air ducts or electricity cables running immediately behind the cut out
area!
 Please work from secure steps or scaffold and avoid trailing wires for your safety and those around you.
 Always turn off the amplifier or other devices in the system when connecting these speakers.
5
Procedure
NOTE: If you are choosing to paint your In-Ceiling loudspeaker, we recommend you do this prior to
installation. We would also recommend using the paint mask for the baffle. Remove the mask after paint has
completely dried. Fit the grille membrane to the inside of the grille after painting.
1. Use template to locate position of cut out. Fig 1 for BR, RS & GS In-Ceiling Products and Fig 2 for Radius InCeiling products. The adhesive backing allows for repositioning a number of times.
7
2. Draw around the template to define the circumference of the cut out - 250mm ( 9 /8 inches ) for BR, RS & GS
13
In-Ceiling products, 173mm (6 /16 Inches) for Radius Inceiling products
3. Remove template and cut hole.
4. Locate speaker cable and connect by pushing the terminals in and releasing to clamp the cables as shown
below Fig 3 for Radius, BR, RS & GS In-Ceiling Products and Fig 4 for Radius Stereo In-Ceiling.
5. Fit back box into prepared hole and tighten fixing clamps. These will move outwards on tightening! DO NOT
OVERTIGHTEN! Once contact is made 2-3 turns are all that is required.
6. TO FINE-TUNE THE SPEAKERS PLEASE REFER TO PAGE 9.
Hole to be cut
250mm ( 9 7/8”
)
Diameter
Hole to be cut
173mm (6 13/16”
)
Diameter
Position of 4
fixing clamps
BR, RS, GS
In-Ceiling Template
Not to scale
Fig 1
Position of 4
fixing clamps
Radius In-Ceiling
Template
Not to scale
Fig 2
Push down to fit cable
Push down to fit cable
Red (Positive)
Black (Negative)
Red (Positive)
Fig 3
Black (Negative)
Fig 4
6
Installation - In-Wall Units
The CP Series In-Wall loudspeakers will provide long term satisfaction in terms of sound quality and reliability
provided they are installed correctly, according to the instructions and conditions contained in this manual. Please
read this installation guide carefully before proceeding. We assume the installer is trained and skilled in the correct
and safe use of hand and power tools, and has a working knowledge of local building and fire regulations/codes as
well as experience of the conditions/services behind walls and ceilings into which these speakers will be installed. IF
IN DOUBT ABOUT YOUR ABILITY TO INSTALL THESE PRODUCTS SAFELY AND CORRECTLY PLEASE CONTACT YOUR
LOCAL AUTHORISED MONITOR AUDIO DEALER OR CUSTOM INSTALLER.
NOW AVAILABLE: Pre-construction brackets. These are for use when installing any CP product before the
plaster board/ rock wall, is fitted. They show the location of the speakers to the builder and give them a solid
secure edge to cut around.
Parts List
PLEASE CHECK YOU HAVE THE FOLLOWING ITEMS IN THIS KIT BEFORE PROCEEDING:






1 x Complete speaker & tweeter assembly fitted to back box.
1 x Grille (which can be painted).
1 x Mounting cut out template (in packaging).
1 x Plastic paint mask (for covering the baffle while painting the frame)
1 x Self adhesive grille membrane (to be attached to the inside the grille after it has been painted).
2 x Spare baffle fixing screws plus guarantee card in this manual.
WARNINGS:
 A minimum depth of 101mm (4 Inches) is required for the back box on the BR, RS & GS In-Wall products to
7
fit into wall/ceiling recess. The Radius In-Wall requires 99mm (3 /8 Inches).
 The fixing clamps require a minimum of 25mm (1 Inch) of surface area around the cut-out hole to ensure a
secure fixing!
3
 The fixing clamps will operate on walls with a minimum thickness of 9mm ( /8 Inches) to a maximum depth of
32mm (1¼ Inches).
 Do not attempt to fix these speakers to your wall if you are unsure of your ability to provide a secure and safe
fixing. IF IN DOUBT CONTACT YOUR LOCAL AUTHORISED MONITOR AUDIO DEALER.
 Ensure that there are no water pipes, air ducts or electricity cables running immediately behind the cut out
area!
 Please work from secure steps or scaffold and avoid trailing wires for your safety and those around you.
 Always turn off the amplifier or other devices in the system when connecting these speakers.
7
Procedure
NOTE: If you are choosing to paint your In-Ceiling loudspeaker, we recommend you do this prior to
installation. We would also recommend using the paint mask for the baffle. Remove the mask after paint has
completely dried. Fit the grille membrane to the inside of the grille after painting.
1. Use template to locate position of cut out. Fig 1 for BR, RS & GS In-Ceiling Products and Fig 2 for Radius InCeiling products. The adhesive backing allows for repositioning a number of times.
3
2. Draw round the perimeter of the cut out –387 x 234mm (15 ¼ x 9 /16 inches ) for BR, RS & GS In-Wall
13
products, 275 x 172mm (10 /16 x 6 ¾ Inches) for Radius In-Wall
3. Remove template and cut hole.
4. Locate speaker cable and connect by pushing the terminals in and releasing to clamp the cables as shown
below Fig 3.
5. Fit back box into prepared hole and tighten fixing clamps. These will move outwards on tightening! DO NOT
OVERTIGHTEN! Once contact is made 2-3 turns are all that is required.
6. TO FINE-TUNE THE SPEAKERS PLEASE REFER TO PAGE 9.
Hole size to be cut
387 x 234mm
(
1
5¼“x93/16”)
Hole size to be cut
275 x 172mm
(10 13/16 ”x6¾”)
Position of 6
fixing clamps
Position of 8
fixing clamps
BR, RS, GS
In-wall template
Radius In-wall
template
Fig 2
Fig 1
Not to scale
Push down to fit cable
Red (Positive)
Black
(Negative)
Fig 3
8
Setting Up CP Loudspeakers
The following adjustments can be made to the tweeter on CP models except BR, RS & GS In-Wall, as follows:
1.
2.
3.
4.
Pivoting tweeters can be tilted up to 18 degrees in all directions to provide optimum coverage.
If the speakers are widely separated such that the music fails to blend into a central image when operated
in stereo mode then tilt the tweeter towards the listening area.
If the Soundstage seems too confined tilt the tweeter away from the listening area.
For further fine-tuning options of your CP In-Ceiling speakers please go to page 8.
Fine-tuning - In-Ceiling and In-wall speakers
The following adjustments can be made to your CP In-Ceiling and In-Wall loudspeakers as follows:
Adjusting H.F (High Frequency) control
(Silver RS CP and Gold CP models only)
The factory H.F setting provides a flat or 0dB level, which will suit the majority of typical installations. However, it is
possible to fine-t
unet
hes
oundf
r
om t
heCPs
peaker
st
os
ui
tar
oom’
s characteristics or preferred listening tastes by
using the following as a guide: a. Setting the switch in the +3dB position will add brightness and additional clarity to the system. This may be
effective in a room with a large amount of soft furnishings.
b. Setting the switch in the -3dB position will reduce the brightness on the system and provide a duller sound.
This may be effective in a room with a lack of soft furnishings, or in an installation with a wooden floor.
Adjusting M.F (Mid-range Frequency) control
(Gold CP models only)
The factory M.F setting provides a flat or 0dB level, which will suit the majority of typical installations. However, it is
possible to fine-tune the sound from the Gold CP In-Ceiling and In-Wall s
peaker
st
os
ui
tar
oom’
scharacteristics or
preferred listening tastes by using the following as a guide: a. Setting the switch in the +3dB position will add presence and additional clarity to the system, particularly in
the vocal region. This may be effective for better resolution of dialogue and speech, or in an installation where
the listening position is a large distance from the speaker.
b. Setting the switch in the -3dBpos
i
t
i
onwi
l
lr
educet
hepr
es
enceandt
hes
ys
t
em wi
l
ls
oundmor
e‘
l
ai
dback’
.
This may be effective where the speaker will be played for background music, or where the listening position
is situated close to the speaker.
9
In-Ceiling Technical Specifications
CPC GS
In-Ceiling
CPC RS
In-Ceiling
CPC BR
In-Ceiling
CPC
RADIUS
In-Ceiling
CPC RADIUS
In-Ceiling
STEREO
Frequency
Response
55Hz –30KHz
60Hz –30KHz
62Hz –22 KHz
60Hz –25KHz
60Hz –25KHz
Impedance
(nominal)
8 Ohms
8 Ohms
8 Ohms
6 Ohms
6 + 6 Ohms
Sensitivity
(1W@1M)
89dB
89dB
88dB
88 dB
88 dB
Maximum SPL
106.5 dBA
105.8 dBA
105 dBA
103 dBA
103 dBA (both
channels driven)
Power
Handling
120W
100W
80W
70W
35W / x 2
(total 70W)
Recommended
Amp
Requirements
30-120W
30-100W
20-80W
5-60W
5-30W x 2
Bass
Alignment
Sealed enclosure
Sealed enclosure
Sealed
enclosure
Sealed
enclosure
Sealed enclosure
Drive Unit
Complement Bass
1x6.
5”C-CAM
bass driver
featuring RST
technology
1x6”C-CAM bass
driver
1x6.
5”MMP2
second
generation Metal
Matrix Polymer
1x5”MMP2
bass driver
1x5”MMP2bass
driver
Drive Unit
Complement Tweeter
Pivoting 25mm CCAM gold alloy
dome with
high power ceramic
magnet system
Pivoting 25mm CCAM gold alloy
dome with
rare earth magnet
Pivoting 25mm
C-CAM gold
alloy dome with
rare earth
magnet
Pivoting 20mm
®
C-CAM gold
alloy dome
2 x 20mm
®
C-CAM gold alloy
dome
Overall
Diameter
281mm
1
(11 /16 inches)
281mm
1
(11 /16 inches)
281mm
1
(11 /16 inches)
214 DIA (mm)
7
8 /16 (Inches)
214 DIA (mm)
7
8 /16 (Inches)
Overall Depth
181mm
1
(7 /8 inches)
181mm
1
(7 /8 inches)
181mm
1
(7 /8 inches)
155 (mm)
1
6 /8 (Inches)
155 (mm)
1
6 /8 (Inches)
Cut-Out Hole
Diameter
250mm
7
(9 /8 inches)
250mm
7
(9 /8 inches)
250mm
7
(9 /8 inches)
Recommended
Mounting
Depth.
mm (inch)
190mm
(7 ½ )
190mm
(7 ½ )
190mm
(7 ½ )
150mm
(6)
150
(6)
Controls
+3db / 0dB / -3dB
High frequency
attenuation witch.
+3db / 0dB / -3dB
Mid-range
frequency
attenuation switch.
+3db / 0dB / -3dB
High frequency
attenuation switch
N/A
N/A
N/A
Fixing type
4posi
t
i
on‘
dog’
type fixings
4posi
t
i
on‘
dog’
type fixings
4posi
t
i
on‘
dog’
type fixings
4posi
t
i
on‘
dog’
type fixings
4posi
t
i
on‘
dog’
t
y
pe
fixings
Connection
Gol
dpl
at
ed‘
push’
type terminals
Gol
dpl
at
ed‘
push’
type terminals
Gold plated
‘
push’
t
y
pe
terminals
Gold plated
‘
push’
t
y
pe
terminals
Gol
dpl
at
ed‘
push’
type terminals
Model
6
173 (mm)
/16 (Inches)
13
6
173 (mm)
/16 (Inches)
13
Baffle material
MDF
MDF
MDF
ABS
ABS
Back Box/
Material
Mineral filled ABS
plastic
(UL –94 V0 fire
rated)
Mineral filled ABS
plastic
(UL –94 V0 fire
rated)
Mineral filled
ABS plastic
(UL –94 V0 fire
rated)
Mineral filled
ABS plastic
(UL - 94 V0 fire
rated)
Mineral filled ABS
plastic
(UL - 94 V0 fire rated)
PreConstruction
CB 8 (Green)
CB 8 (Green)
CB 8 (Green)
CB 5 (Blue)
CB 5 (Blue)
Unit weight Kg
(lb)
3.1Kg (6.8Ib)
2.5Kg (5.5Ib)
2.4Kg (5.3lb)
1.55Kg (3.4lb)
1.6Kg (3.5lb)
10
In-Wall Technical Specifications
CPW GS
In-Wall
CPW RS
In-Wall
CPW BR
In-Wall
CPW RADIUS
In-wall
Frequency
Response
55Hz –30KHz
60Hz –30KHz
62Hz –22 KHz
60Hz –25KHz
Impedance
(nominal)
8 Ohms
8 Ohms
8 Ohms
6 Ohms
Sensitivity
(1W@1M)
89dB
89dB
88dB
88 dB
Maximum SPL
106.5 dBA
105.8 dBA
105 dBA
103 dBA
Power Handling
120W
100W
80W
70W
Recommended
Amp Requirements
30-120W
30-100W
20-80W
5-60W
Bass Alignment
Sealed enclosure
Sealed enclosure
Sealed enclosure
Sealed enclosure
Drive Unit
Complement –
Bass
1x6.
5”C-CAM bass
driver featuring RST
technology
1x6”C-CAM bass
driver
1x6.
5”MMP2second
generation Metal Matrix
Polymer
1x5”MMP2bass
driver
Drive Unit
Complement Tweeter
25mm C-CAM gold
alloy dome with high
power ceramic magnet
system and rear low
resonance chamber
25mm C-CAM gold
alloy dome with rare
earth magnet
25mm C-CAM gold
alloy dome with rare
earth magnet
Pivoting 20mm C®
CAM gold alloy dome
Overall Size
HxW
(Inches)
423 x 270mm
5
5
(16 /8 x 10 /8 )
423 x 270mm
5
5
(16 /8 x 10 /8 )
423 x 270mm
5
5
(16 /8 x 10 /8 )
313 x 212mm
5
5
(12 /16 x 8 /16 )
Overall Depth
(Inches)
100mm
15
(3 /16 )
100mm
15
(3 /16 )
100mm
15
(3 /16 )
99mm
7
(3 /8 )
Cut-Out Hole Size
HxW
(Inches)
387 x 234mm
3
(15 ¼ x 9 /16 )
387 x 234mm
3
(15 ¼ x 9 /16 )
387 x 234mm
3
(15 ¼ x 9 /16 )
275 x 172mm
13
(10 /16 x 6 ¾ )
Recommended
Mounting Depth
101mm
(4 inches)
101mm
(4 inches)
101mm
(4 inches)
95mm
3 ¾ (Inches)
Controls
+3db / 0dB / -3dB
High frequency
attenuation switch.
+3db / 0dB / -3dB
Mid-range frequency
attenuation switch.
+3db / 0dB / -3dB
High frequency
attenuation switch
N/A
N/A
Fixing Type
8posi
t
i
on‘
dog’
t
y
pe
fixings
8posi
t
i
on‘
dog’
t
y
pe
fixings
8posi
t
i
on‘
dog’
t
y
pe
fixings
6posi
t
i
on‘
dog’
t
y
pe
fixings
Connection
Gol
dpl
at
ed‘
push’t
y
pe
terminals
Gol
dpl
at
ed‘
push’t
y
pe
terminals
Gol
dpl
at
ed‘
push’t
y
pe
terminals
Gold pl
at
ed‘
push’t
y
pe
terminals
Baffle Material
MDF
MDF
MDF
ABS
Back Box Material
Mineral filled
ABS plastic
(UL –94 V0 fire rated)
Mineral filled
ABS plastic
(UL –94 V0 fire rated)
Mineral filled
ABS plastic
(UL –94 V0 fire rated)
Mineral filled
ABS plastic
(UL –94 V0 fire rated)
Pre-Construction
Bracket
WB 8 (Green)
WB 8 (Green)
WB 8 (Green)
WB 5 (Blue)
Unit Weight Kg (lb)
4.4Kg (9.6Ib)
3.2Kg (7Ib)
3.3Kg (7.2lb)
1.83Kg (4.1lb)
Model
11
Guarantee and Service
The guarantee becomes valid upon completion of the attached guarantee card and its return within 30 days of
purchase.
This guarantee is void if the serial number has been removed or defaced.
This equipment has been fully tested prior to dispatch from the factory. Both the craftsmanship and the performance
of this product is guaranteed against manufacturing defects for the period of three years from the date of purchase
(see conditions below), provided that the product was supplied by an authorised Monitor Audio retailer under the
consumer sal
eagr
eement
.(
Thewor
ds‘
cons
umers
al
e’s
hal
lbecons
t
r
uedi
naccor
dancewi
t
hs
ect
i
on15oft
hes
uppl
y
of goods act 1973). Monitor Audio accepts no responsibility for defects arising from accident, misuse, abuse, wear
and tear, modification or operation outside of that specified within this instruction manual. Neither will responsibility be
accepted for damage or loss occurring during transit to or from the parties claiming under this guarantee.
This guarantee covers both labour and parts. The liability of Monitor Audio is limited to the cost of repair or
replacement of the defective parts (at the discretion of Monitor Audio) and under no circumstances extends to
consequential losses or damage.
Claims under this Guarantee
The equipment should be returned in its packaging to the original supplier where possible, or to any other authorised
Monitor Audio dealer. If it is not possible to return the equipment by hand, then it should be sent carriage prepaid via a
reputable carrier. If the original packing is not available replacement packaging can be purchased from Monitor Audio.
If you have any difficulties complying with these requirements please contact us at the following address:
Monitor Audio Ltd.
Unit 2, 24 Brook Road
Rayleigh
Essex
SS6 7XL
England
Tel:
44 (0) 1268 740580
Fax:
44 (0) 1268 740589
Internet: www.monitoraudio.co.uk
Email: info@monitoraudio.co.uk
This guarantee does not affect the statutory rights of the consumer under UK law and or relevant consumer laws in
other countries or states.
Monitor Audio reserve the right to alter specifications at any time without notice if it is considered that an improvement
can be made to the product.
Declaration of Conformity
Low Voltage Directive 2006/95/EC
Electromagnetic Compatibility Directive 89/336/EEC
We, Monitor Audio Ltd.
24 Brook Road
Rayleigh
Essex
SS6 7XL
England
07
Declare in own responsibility, that the products described in this manual are in
compliance with technical standards:
EN 61000-6-1 : 2001
EN 61000-6-3 : 2007
EN 55013
: 2001
Dean Hartley (Technical Director)
EN 50020
: 2002
Monitor Audio Ltd
England
12
Warnungshinweis
Die zum Wand/Decken-Einbau vorgesehenen Lautsprecher der CP Serie werden Ihnen auf lange Zeit mit ihrer vorzüglichen Tonqualität und
Zuverlässigkeit viel Freude bereiten, vorausgesetzt, dass sie vorschriftsmäßig nach den in diesem Handbuch angegebenen Anleitungen und
Bedingungen eingebaut werden. Lesen Sie bitte vor Beginn der Arbeiten diese Installationsanleitungen sorgfältig, da wir voraussetzen, dass der
Installateur im vorschriftsmäßigen und sicheren Gebrauch von Elektrowerkzeugen unterwiesen und erfahren ist. Es wird ebenso vorausgesetzt, dass er
ausreichende Kenntnisse der örtlichen Bau und Brandschutzbestimmungen besitzt, sowie entsprechende Erfahrung des Unterputzzustandes und der
eventuell vorhandenen Leitungen in Wänden und Zimmerdecken besitzt, in welche diese Lautsprecher eingebaut werden sollen. SOLLTEN SIE
DARAN ZWEIFELN; DIESE ARBEITEN MIT SICHERHEIT- UND ORDNUNGSGEMÄSS AUSFÜHREN ZU KÖNNEN, WENDEN SIE
SICH BITTE AN IHREN AUDIO-VERTRAGSHÄNDLER.
WARNUNGSHINWEIS:







Es wird eine Mindesteinbautiefe von 190 mm (7.5 Zoll ) für den Deckeneinbau der Backbox benötigt. Für den Wandeinbau sind
98 mm (4 Zoll) vorzusehen.
Die Befestigungsklemmen benötigen eine Oberfläche von 25 mm (1 Zoll) um das ausgeschnittene Loch herum, um eine sichere
Befestigung zu gewähren!
Die Befestigungsklemmen können bei Decken oder Wänden mit einer Mindestdicke von 9 mm (0,35 I) bis zu einer Mindesttiefe
von 32 mm (1,25 Zoll) angewendet werden
Versuchen Sie nicht, diese Lautsprecher an Ihrer Wand oder Decke anzubringen, wenn Sie nicht voll überzeugt sind, dass Sie
imstande sind, diese vorschriftsmäßig und sicher zu montieren. IM ZWEIFELSFALLE WENDEN SIE SICH BITTE AN IHREN
ZUGELASSENEN ÖRTLICHEN AUDIOHÄNDLER.
Vergewissern Sie sich, dass sich keine Wasser- Luft- oder Elektroleitungen hinter dem Ausschnitt befinden!
Benutzen Sie bitte immer nur sichere Tritte oder Leitergerüste und vermeiden Sie im Interesse Ihrer Sicherheit sowie der aller
anwesenden Personen herabhängende und auf dem Boden schleifende Kabel und Leitungen.
Bei Anschluss dieser Lautsprecher müssen die Verstärker sowie alle weiteren Geräte im System ausgeschaltet sein.
Avvertimenti
La Serie CP di altoparlanti incassati nel soffitto e nelle pareti offrirà un ottimo funzionamento in termini di qualità Sonora ed affidabilità, purché gli
altoparlanti siano installati correttamente, seguendo le istruzioni e le condizioni contenute in questo manuale. Si prega di leggere attentamente questa
g
ui
d
aa
l
l
’
i
ns
t
a
l
l
a
z
i
onep
r
i
mad
ip
r
o
c
e
de
r
e
,po
i
c
h
ép
r
e
s
umi
a
moc
hel
’
i
n
s
t
a
l
l
a
t
o
r
es
i
aa
d
de
s
t
r
a
t
oes
i
ai
ng
r
a
d
od
iut
i
l
i
z
z
a
r
eg
l
ia
t
t
r
e
z
z
ima
n
ua
l
ie
de
l
e
t
t
r
i
c
i
.
Eda
bb
i
ai
no
l
t
r
eun
ac
onos
c
e
nz
ao
pe
r
a
t
i
v
ade
l
l
’
e
di
f
i
c
i
ol
oc
a
l
eed
e
l
l
eno
r
me
/
c
o
d
i
c
ia
n
t
i
nc
e
nd
i
oec
on
os
c
al
e condizioni/i servizi dietro pareti e soffitti
nei quali saranno installati questi altoparlanti. IN CASO DI DUBBI SULLA PROPRIA ABILITÀ AD EFFETTUARE QUESTA
INSTALLAZIONE IN MODO CORRETTO E SICURO, SI PREGA DI CONTATTARE IL PROPRIO CONCESSIONARIO LOCALE
AUTORIZZATO ALLA VENDITA DI APPARECCHI AUDIO.
ATTENZIONE:







E’necessar
i
aunapr
of
ondi
t
àmi
ni
madi190mm per
chél
acassapost
er
i
or
epossaesser
ei
nst
al
l
at
anelv
anodel soffitto. Quella
da incassare nella parete necessita di uno spazio di 98 mm.
I dispositivi di fissaggio necessitano di una superficie minima di 25 mm intorno al foro intagliato per assicurare un fissaggio
sicuro!
I dispositivi di fissaggio saranno funzionali in soffitti e pareti che abbiano uno spessore di almeno 9 mm fino ad uno spessore
massimo di 32 mm.
Non si deve tentare di fissare questi altoparlanti in un soffitto o una parete se non si è certi della propria abilità di effettuare
un’
i
nst
al
l
az
i
one appr
opr
i
at
a e si
cur
a.IN CASO DI DUBBI CONTATTARE IL PROPRIO CONCESSIONARIO LOCALE
AUTORIZZATO ALLA VENDITA DI APPARECCHI AUDIO.
Accer
t
ar
si
chenonv
isi
anodit
ubidel
l
’
acqua,condot
t
id’
ar
i
aocav
iel
et
t
r
i
ci
i
nst
al
l
at
iappenadi
et
r
ol
’
ar
eai
nt
agl
i
at
a!
Lavorare su scale o impalcature sicure ed evitare di tirare dei fili per la propria sicurezza e quella di altre persone.
Spegner
esempr
el
’
ampl
i
f
i
cat
or
eoal
t
r
i
di
sposi
t
i
v
idel
l
’
i
mpi
ant
oquandosi
col
l
eganoquest
ial
t
opar
l
ant
i
.
13
Advertencias
La CP Series de altavoces de empotrado en el techo y en la pared ofrecerán una satisfacción a largo plazo en concepto de calidad del sonido y
fiabilidad, siempre y cuando se instalen correctamente, según las instrucciones y condiciones contenidas en este manual. Antes de proceder, lea
detenidamente esta guía de instalación en la que se supone que el instalador está capacitado y es hábil en el uso correcto y seguro de herramientas
manuales y eléctricas, y que tiene conocimientos prácticos de las regulaciones / códigos locales en materia de construcción e incendios, así como
experiencia en cuanto a las condiciones / servicios que se encuentran detrás de los techos y paredes en los que se instalarán estos altavoces. EN
CASO DE DUDA DE QUE SEA CAPAZ DE INSTALAR ESTOS DISPOSITIVOS DE UNA MANERA SEGURA Y CORRECTA,
SÍRVASE CONTACTAR CON SU DISTRIBUIDOR AUTORIZADO LOCAL DE AUDIO MONITORES
ADVERTENCIAS:







Se requiere una profundidad mínima de 190 mm (7,5 pulgadas) para que la caja de respaldo de empotrado en el techo
quepa en el rebaje. La de empotrado en la pared requiere de 98 mm (4 pulgadas)
¡Las grapas de fijación requieren un área de superficie de 25 mm (1 pulgada), como mínimo, alrededor del agujero perforado
para garantizar una fijación segura!
Las grapas de fijación servirán en techos o paredes con un espesor mínimo de 9 mm (0,35 pulgadas) hasta una profundidad
máxima de 32 mm (1,25 pulgadas)
No intente instalar estos altavoces en el techo o pared si no está seguro de que sea capaz de ofrecer una instalación
correcta y segura . EN CASO DE DUDA CONTACTE CON SU DISTRIBUIDOR AUTORIZADO LOCAL DE AUDIO
MONITORES.
¡Cerciórese de que no haya tuberías de agua, ductos de aire o cables eléctricos que pasen inmediatamente por detrás del
área perforada!
Para la instalación use por favor escaleras o andamiaje y evite dejar alambres colgados por su propia seguridad y la de los
que le rodean.
Siempre apague el amplificador u otros dispositivos del sistema cuando conecte estos altavoces.
Avertissements
La série CP de haut-parleurs encastrés dans les murs et les plafonds fourniront une satisfaction à long terme quant à la qualité du son et à la fiabilité, à
c
ond
i
t
i
ond
’
ê
t
r
ei
ns
t
a
l
l
é
sc
o
r
r
e
c
t
e
me
n
t
,c
o
nf
o
r
mé
me
n
ta
uxi
ns
t
r
uc
t
i
o
nse
ta
uxc
on
di
t
i
onsc
on
t
e
n
ue
sd
a
nsc
e
t
t
eno
t
i
c
e
.Lisez attentivement cette notice
a
v
a
n
tdec
omme
nc
e
rl
’
i
ns
t
a
l
l
a
t
i
o
n.No
uss
uppos
onsq
uel
’
i
ns
t
a
l
l
a
t
e
ure
s
tf
o
r
mée
tc
omp
é
t
e
n
te
tq
u’
i
ls
a
i
tut
i
l
i
s
e
rl
e
so
ut
i
l
sàma
i
ne
tl
e
so
ut
i
l
s
é
l
e
c
t
r
i
q
ue
sc
o
r
r
e
c
t
e
me
nte
td
’
unema
n
i
è
r
es
ûr
e
.No
uss
up
pos
o
nsé
g
a
l
e
me
n
tq
u’
i
launec
onn
a
i
s
s
a
nc
ep
r
a
t
i
q
uede
sr
è
g
l
e
me
nt
s
/
c
ode
sl
oc
a
uxr
e
l
a
t
i
f
sa
ux
constructions et aux i
n
c
e
nd
i
e
se
tq
u’
i
laun
ee
xp
é
r
i
e
nc
ede
sc
on
di
t
i
o
ns
/
s
e
r
v
i
c
e
sde
r
r
i
è
r
el
e
smur
se
tl
e
spl
a
f
on
dsd
a
nsl
e
s
q
ue
l
sc
e
sh
a
ut
-parleurs seront
installés. SI VOUS AVEZ UN DOUTE QUELCONQUE SUR VOTRE CAPACI
TÉ D’
I
NSTALLER CES HAUT-PARLEURS
CORRECTEMENTETD’
UNEMANI
ÈRESÛRE, CONTACTEZ VOTRE REVENDEUR LOCAL AGRÉÉ DE MATERIEL HI-FI.
AVERTISSEMENTS :







I
lf
autunepr
of
ondeurd’
aumoi
ns190mm pourencast
r
erl
eboî
t
i
erar
r
i
èr
edansl
eplafond. La profondeur nécessaire pour
l
’
encast
r
ementdansl
emur est de 98 mm.
Les bridesdef
i
x
at
i
onontbesoi
nd’
unesur
f
aced’
env
i
r
on25mm aut
ourdut
r
oudécoupépourf
our
ni
runef
i
x
at
i
onf
er
me!
Lesbr
i
desdef
i
x
at
i
onsontadéquat
espourêt
r
eut
i
l
i
séessurdespl
af
ondsetdesmur
sd’
uneépai
sseurmi
ni
mum de9mm et
d’
unepr
of
ondeurmax
i
mum de 32 mm.
N’
essay
ezpasdef
i
x
erceshaut
-par
l
eur
sdansv
ot
r
epl
af
ondoudansv
ot
r
emursiv
ousn’
êt
espascer
t
ai
ndepouvoi
robt
eni
r
une fixation ferme et sûre. EN CAS DE DOUTE, CONTACTEZ VOTRE REVENDEUR LOCAL AGRÉÉ DE MATERIEL HI-FI.
Assurez-vousqu’
i
ln’
yapasdecondui
t
esd’
eau,decondui
t
sd’
ai
rnidecâbl
esél
ect
r
i
quesj
ust
eder
r
i
èr
el
’
endr
oi
tpr
év
u
d’
encast
r
ement
.
Travaillez sur un escabeau ou sur un échafaudage sûr et évitez de laisser traîner des fils électriques pour votre sécurité et
celle de ceux autour de vous.
Met
t
ezt
ouj
our
shor
st
ensi
on l
’
ampl
i
f
i
cat
eurou l
es aut
r
esdi
sposi
t
i
f
sdansl
esy
st
ème l
or
sque v
ousconnect
ezces haut
parleurs.
© 2004 Monitor Audio Ltd.
24 Brook Road, Rayleigh, Essex SS6 7XL England
Revision version 6
14
Download PDF