Mitel | 5324 | Specifications | Mitel 5324 Specifications

MITEL
5312/5324 IP Phones
SIP User and Administrator Guide
Release 7.2
5312 and 5324 IP Phone SIP User and Administrator Guide
NOTICE
The information contained in this document is believed to be accurate in all respects but is
not warranted by Mitel Networks™ Corporation (MITEL®). The information is subject to
change without notice and should not be construed in any way as a commitment by Mitel or
any of its affiliates or subsidiaries. Mitel and its affiliates and subsidiaries assume no
responsibility for any errors or omissions in this document. Revisions of this document or new
editions of it may be issued to incorporate such changes.
Mitel is a registered trademark of Mitel Networks Corporation.
Internet Explorer is a trademark of Microsoft Corporation.
Netscape Navigator is a trademark of Netscape Communications Corporation.
Other product names mentioned in this document may be trademarks of their respective
companies and are hereby acknowledged.
5312/5324 IP Phones SIP User and Administrator Guide
Release 7.2
October, 2008
58011941
®,™ Trademark of Mitel Networks Corporation
© Copyright 2008 Mitel Networks Corporation
All rights reserved
- ii -
Table of Contents
TABLE OF CONTENTS
GETTING STARTED ................................................................................................. 1
SIP User Accounts and Passwords ..................................................................................... 1
SIP Administrative Mode ..................................................................................................... 1
About Your SIP Phone......................................................................................................... 1
Elements of Your Phone ................................................................................................................. 2
Ring/Message indicators ..................................................................................................... 5
TIPS FOR YOUR COMFORT AND SAFETY ............................................................ 6
Don't cradle the handset! ..................................................................................................... 6
Protect your hearing ............................................................................................................ 6
Adjust the viewing angle ...................................................................................................... 6
Call Encryption Indicator ................................................................................................................. 7
Accessories for Your Phone ................................................................................................ 7
Headsets ......................................................................................................................................... 7
Conference Units............................................................................................................................. 7
Supporting Documentation .................................................................................................. 7
Accessing the Web Configuration Tool Online Help ....................................................................... 7
Accessing Other Documentation..................................................................................................... 7
CUSTOMIZING YOUR PHONE................................................................................. 9
Superkey Menu Interface..................................................................................................... 9
Web Configuration Tool ....................................................................................................... 9
Web Configuration Tool Accounts and Passwords......................................................................... 9
Accessing the Web Configuration Tool ......................................................................................... 10
Display-Assisted Feature Selection ................................................................................... 10
Selecting Menu Options ................................................................................................................ 10
Entering Numbers and Letters ...................................................................................................... 10
Ringer Control.................................................................................................................... 11
Handset Volume Control.................................................................................................... 12
Speaker Volume Control.................................................................................................... 12
Display Contrast Control .................................................................................................... 12
Display Language .............................................................................................................. 12
Personal Keys.................................................................................................................... 12
Programming a Personal Key ....................................................................................................... 13
Line Keys....................................................................................................................................... 13
Pre-assigned Personal Keys ......................................................................................................... 14
- iii -
5312 and 5324 IP Phone SIP User and Administrator Guide
Speed Dial Keys ................................................................................................................ 14
Program a Speed Dial Key............................................................................................................ 14
Delete a Speed Dial Key ............................................................................................................... 15
Programming Features in Speed Dial Keys .................................................................................. 15
MAKING AND ANSWERING CALLS ..................................................................... 16
Making Calls ...................................................................................................................... 16
Dial by Number.............................................................................................................................. 16
Dial by Name (5324 IP Phone only).............................................................................................. 16
Dial by SIP URL or IP Address (5324 IP Phone only) .................................................................. 16
Dial by Phone Book Entry ............................................................................................................. 17
Dial by Call Logs Entry .................................................................................................................. 17
Redial ............................................................................................................................................ 17
Using Speed Dial Keys.................................................................................................................. 17
Answering Calls ................................................................................................................. 18
Answer a Call ................................................................................................................................ 18
Auto Answer .................................................................................................................................. 18
Answer a Call Waiting ................................................................................................................... 19
Calling and Called Party Display................................................................................................... 19
CALL HANDLING ................................................................................................... 20
Hold ................................................................................................................................... 20
Hold a Call..................................................................................................................................... 20
Retrieve a Call from Hold .............................................................................................................. 20
Change On-Hold Settings ............................................................................................................. 20
Call Forward ...................................................................................................................... 20
Program Call Forward ................................................................................................................... 20
Enable/Disable Call Forward......................................................................................................... 21
Call Transfer ...................................................................................................................... 21
Transfer a Call to an Unconnected Third Party............................................................................. 21
Transfer a Call to a Third Party Already on Hold .......................................................................... 22
Conference Call (Three-Way) ............................................................................................ 22
Add a Third Party to a Call in Progress......................................................................................... 22
Add a Party On Hold to a Call in Progress.................................................................................... 22
Leave a Conference Call............................................................................................................... 23
Messages - Advisory ......................................................................................................... 23
Create an Advisory Message ........................................................................................................ 23
Enable/Disable your Advisory Message........................................................................................ 23
Messaging – Voice Mail ..................................................................................................... 23
Access your Voice Mail Messages................................................................................................ 24
USING ADVANCED FEATURES ............................................................................ 25
Do Not Disturb ................................................................................................................... 25
- iv -
Table of Contents
Enable/Disable Do Not Disturb ..................................................................................................... 25
Call Logs............................................................................................................................ 25
View a Call Log Entry .................................................................................................................... 25
Delete a Call Log Entry ................................................................................................................. 26
Call a Call Logs Entry.................................................................................................................... 26
Call Forking........................................................................................................................ 26
Handset, Handsfree and Headset Modes.......................................................................... 27
Switch between Handset and Handsfree ...................................................................................... 27
Switch between Handset and Headset ......................................................................................... 27
Switch between Headset and Handsfree ...................................................................................... 27
Muting a Call...................................................................................................................... 27
Phone Book ....................................................................................................................... 28
Create a Phone Book Entry .......................................................................................................... 28
Modify a Phone Book Entry........................................................................................................... 28
Delete a Phone Book Entry........................................................................................................... 29
Call a Phone Book Entry ............................................................................................................... 29
Shared Lines and Keys...................................................................................................... 29
Shared Line Programming Requirements:.................................................................................... 29
Programming Shared Line Keys ................................................................................................... 29
Line Key Status ............................................................................................................................. 30
RSS (Web) Feed ............................................................................................................... 30
Enable/Disable RSS Feed............................................................................................................. 30
Time and Date ................................................................................................................... 30
Change the Time and Date ........................................................................................................... 31
ADMINISTRATOR TOOLS ..................................................................................... 32
SIP Administrator Phone Passwords ................................................................................. 32
Change Phone Passwords............................................................................................................ 32
SIP User Accounts............................................................................................................. 32
Configure/Modify a SIP User account ........................................................................................... 32
View a User Name ........................................................................................................................ 33
Device Parameters ............................................................................................................ 33
Protocols............................................................................................................................ 33
Enable/Disable Protocols .............................................................................................................. 33
SRTP Call Encryption Indicator..................................................................................................... 34
Viewing/Modifying the Network Settings............................................................................ 34
View the IP and MAC Addresses .................................................................................................. 34
Modifying Network Settings........................................................................................................... 34
Upgrade the Phone’s Firmware ......................................................................................... 35
View the Firmware Version ........................................................................................................... 35
Upgrading the Firmware................................................................................................................ 35
-v-
5312 and 5324 IP Phone SIP User and Administrator Guide
Automating Firmware Upgrades ................................................................................................... 36
Configuring Voice Mail .................................................................................................................. 36
Adjust Daylight Savings ..................................................................................................... 37
Configuration Files............................................................................................................. 37
Hot Line ............................................................................................................................. 37
Media Configuration........................................................................................................... 37
Main Program and Boot Program Configuration Options .................................................. 37
Global RSS Feed............................................................................................................... 37
SPECIFICATIONS................................................................................................... 39
GLOSSARY............................................................................................................. 39
- vi -
Getting Started
Getting Started
The Mitel 5312 and 5324 IP Phones are full-feature, dual port, dual mode telephones that
provide voice communication over an IP network. Each features a back-lit liquid crystal
display (LCD) screen, display-assisted access to features, on-hook dialing and off-hook voice
announce with handsfree answerback, and a large ring/message indicator.
In SIP mode, the Mitel™ 5312 and 5324 IP Phones manage their own call states and
features. SIP uses the Internet to connect your phone to other SIP phones. You can make
calls on the Public Switched Telephone Network (PSTN), or “regular”, phone network. You
can also call other SIP phones by dialing SIP URL or IP address. If you are registered with a
SIP Service Provider, you may also be able to dial by user ID name or extension number.
SIP phones have advanced features like shared lines: Bridged Line Appearances (BLA) in
Sylantro environments and Shared Call Appearances (SCA) in Broadsoft environments. For
information on how to program and change features on your SIP-supported phone, refer to
this guide and to the Web Configuration Tool online Help (see Supporting Documentation on
page 7).
SIP User Accounts and Passwords
Your Administrator usually configures SIP accounts for SIP phone Users and Administrators.
You need a SIP User account in order to
• Register your phone with your SIP Service Provider
• Make calls by dialing a user ID name or extension number
If you do not have a SIP user account, you can still use your phone with limited access to
SIP features and functionality.
SIP Administrative Mode
Administrators need an administrator user account and password to
• Modify network configuration settings and SIP Service Provider information
• Access SIP setting menus through the phone’s Superkey menu interface and Web
Configuration Tool.
See Administrator Tools on page 32 for more information.
About Your SIP Phone
The 5312 and 5324 IP Phones have eight fixed-function keys and two arrow keys. The 5312
offers 12 personal keys, and the 5324 offers 24 personal keys for one-touch access to
features. The 5312 and 5324 IP Phones offer display-assisted selection of features, on-hook
dialing, handsfree speakerphone capability, and a large Ring/Message Indicator.
For more key and feature information, see Elements of Your Phone on page 2.
-1-
5312 and 5324 IP Phone SIP User and Administrator Guide
Elements of Your Phone
Each element is numbered according to the call-outs (e.g. X) in Figure 1 and Figure 2 on
page 3. The 5312 IP Phone does not have softkeys.
-2-
Getting Started
Figure 1: 5312 IP Phone
Figure 2: 5324 IP Phone
-3-
5312 and 5324 IP Phone SIP User and Administrator Guide
Elements of Your Phone
Element
Function
1) Display
Provides a two–line, 20–character liquid crystal display (LCD) viewing area that assists
you in selecting and using phone features, accessing your voice mail, and identifying
callers. When you are using the Superkey menu interface, prompts and feature
information appear on the display screen. For information on selecting menu options with
or without softkeys, see "Selecting Menu Options" elsewhere in this guide.
2) Softkeys (5324 IP
Phone only)
Context-sensitive keys change depending on the modes of the operation and the menu
currently displayed. Softkeys enable you to easily view and select a variety of features.
3) Ring/Message
Indicator
Flashes to signal an incoming call and to indicate a message waiting in your voice
mailbox.
4) Volume, Speaker
and Mute Controls
Provide the following audio control capability:
(UP) and
speakers.
(DOWN) provide volume control for the ringer, handset, and handsfree
(SPEAKER) enables and disables Handsfree mode.
(MUTE) enables Mute, which allows you to temporarily turn your phone's handset,
headset or handsfree microphone off during a call.
5) Fixed Function Keys
Give you access to the following phone functions:
(SUPERKEY) : provides access to menus for your phone's additional features. Note :
When navigating through Superkey menu options, press
(SUPERKEY) to back up one menu level.
(CANCEL) or
(CANCEL) : ends a call when pressed during the call, and, when you are
programming the phone, eliminates any input and returns to the previous menu level.
(REDIAL) : calls the last number dialed.
(HOLD) : places the current call on hold.
(TRANS/CONF) : initiates a call transfer or establishes a three–party conference
call.
(MESSAGE) : provides access to your voice mailbox and flashes to notify you of
messages waiting in your voice mailbox. Note : The Ring/Message indicator also flashes
when messages are waiting.
6) Keypad
Use to dial.
7) Programmable
Personal Keys and
Designation Card
Provide one-touch access to Speed Dial, Shared Lines, Call Logs, Headset, Phonebook,
Do Not Disturb, and Advisory Message features.. See Programming a Personal Key on
page 13.
Designation Card
Write the name (contact, feature, or line) of the Personal keys that you program on the
designation card (use the side of the card with the textboxes provided).
Use the slot behind the plastic cover at the bottom of the phone to remove/insert the
designation card..
8) Handsfree Speaker
Provides sound for Handsfree calls and background music.
9) Handset
Use for handset calls. If you are in headset or handsfree mode, you do not need to use
the handset.
-4-
Getting Started
Ring/Message indicators
When indicator is
it means that
Flashing rapidly
Your phone is ringing
Flashing slowly
A message or callback message is waiting at your phone
On
Your phone is ringing another phone
Off
Your phone is idle, or you are on a call
-5-
5312 and 5324 IP Phone SIP User and Administrator Guide
TIPS FOR YOUR COMFORT AND SAFETY
Don't cradle the handset!
Prolonged use of the handset can lead to neck, shoulder, or back discomfort, especially if you
cradle the handset between your ear and shoulder. If you use your phone a lot, you may find
it more comfortable to use a headset. See the section on headset usage elsewhere in this
guide for more information.
Protect your hearing
Your phone has a control for adjusting the volume of the handset receiver or headset.
Because continuous exposure to loud sounds can contribute to hearing loss, keep the
volume at a moderate level.
Adjust the viewing angle
The stand built into your phone tilts to give you a better view of the keys.
To tilt your telephone for better viewing:
1. Turn the phone so that the front faces away from you.
2. Hold the base unit firmly and press the release tabs on the sides of the stand to detach
the base unit.
3. Hinge the hooks of the base unit into the notches on the back of the phone and snap into
place as follows:
a. For a high-angle mount, hinge the two lower hooks into the bottom set of notches
and snap the two upper hooks into the middle set of notches.
b. For a low-angle mount, hinge the two lower hooks into the middle set of notches and
snap the two upper hooks into the top set of notches.
-6-
TIPS FOR YOUR COMFORT AND SAFETY
Call Encryption Indicator
The 5312 and 5324 IP Phones automatically provide Secure Real-time Transport Protocol
(SRTP) voice encryption when connected to a phone that also supports SRTP. A “secured
call” icon (closed padlock) appears on the display for encrypted calls, and for conference
calls in which all connected parties support SRTP. An “unsecured call” icon (open padlock)
appears on the display when the call connection is not secured (the connected party or
parties do not support SRTP encryption). For an icon to appear, SRTP must be enabled. You
can enable or disable SRTP on your phone using the Feature Configuration page of the Web
Configuration Tool. (See Accessing the Web Configuration Tool Online Help on page 7.)
Note: The padlock icon appears only when you are speaking to a party; it does not appear if
you receive a busy signal.
Accessories for Your Phone
Headsets
The 5312 and 5324 IP Phones support a Mitel-approved headset with a Feature Control
Switch. Install the headset only in the dedicated headset jack on the back of the phone.
Installation disables your handset microphone. Disconnecting the headset at the jack or at
the quick-disconnect plug restores handset operation. If handset operation is required for an
extended period of time, press the Headset key to return the phone to handset mode.
Conference Units
Mitel SIP provides support for the Mitel 5310 IP Conference Unit for use with the 5312 and
5324 IP Phones. For more information about the conference unit, refer to the 5310 IP
Conference Unit documentation (see Supporting Documentation on page 7) or contact your
Administrator.
Supporting Documentation
Accessing the Web Configuration Tool Online Help
To access programming instructions in the Web Configuration Tool online Help:
1. Access the Web Configuration Tool Home Page (see Accessing the Web Configuration
Tool on page 10).
2. Scroll to the bottom of the page.
3. In the left pane, under Support, click Help. The Help page opens, presenting links to
this guide and the User Web Configuration Tool online Help.
Note: If you have administrative privileges, you will have access to both the User and the
Administrator Web Configuration Tool online Help systems.
Accessing Other Documentation
To access other Mitel phone and peripheral documentation:
1. In your browser, go to www.mitel.com
-7-
5312 and 5324 IP Phone SIP User and Administrator Guide
2. Click Resources
3. From the Documentation list, select Guides and then click User Guides.
-8-
Customizing Your Phone
Customizing Your Phone
To customize and use your phone features, use either of the following two interfaces:
• Superkey Menu Interface
• Web Configuration Tool
Superkey Menu Interface
The fixed-function keys provide access most features on your phone. The phone’s Superkey
menu interface provides access to additional features.
To access the Superkey menu interface, press the blue
(SUPERKEY).
Web Configuration Tool
The Web Configuration Tool is an optional tool that you can use in addition to your phone to
make calls and to personalize and modify your phone settings.
You can access the Web Configuration from any personal computer (PC) connected to the
Internet and running a web browser that is either
• Netscape Navigator 4.8 or later
• Internet Explorer 4 or later
• Any other equivalent browser.
Note: If your network is protected by a firewall, you may not be able to access your phone
using the Web Configuration Tool from outside the firewall.
Web Configuration Tool Accounts and Passwords
You must have either a User or Administrator account to access the tool. Your account
determines the type of web configuration pages you can access when you connect to the
phone.
Your Administrator may change the default user name and password settings. If necessary,
obtain your new user name and password from your Administrator.
Table 1: Web Configuration Tool Default User Names and Passwords
Default User Name
User
user
Default Password
(5312 IP Phone)
hello
Default Password
(5324 IP Phone)
hello
Note: For Administrator default user name and password, see Administrator Tools on page
32.
-9-
5312 and 5324 IP Phone SIP User and Administrator Guide
Accessing the Web Configuration Tool
To access the Web Configuration Tool:
1. On your phone, do the following to obtain your phone’s IP address:
• Press
(SUPERKEY).
• Press the Line 1 (Prime Line) key. Your phone’s IP address appears.
• Write down the IP address, and then press
default display.
(SUPERKEY) to return to the
2. On your PC, launch your browser.
3. In your browser’s URL or Address field, enter your phone’s IP address. The Web
Configuration Tool login screen appears.
4. In the appropriate fields, enter your Web Configuration Tool user name and password.
5. Click OK. The Web Configuration Tool Home Page launches.
Note: If you are a SIP Administrator, see Administrator Tools on page 32 for administrative
options.
Note: If you need help programming features, access the Web Configuration Tool online
Help (see Accessing the Web Configuration Tool Online Help on page 7).
Display-Assisted Feature Selection
Selecting Menu Options
On a 5312 IP Phone, press *, 0 and # on the keypad to select menu items on the display. For
example, if options * =YES 0=DEFAULT #=NO appear and you want to select YES, press *.
On a 5324 IP Phone, press the softkeys to select menu items on the display.
Entering Numbers and Letters
5312 IP Phone
On the 5312 IP Phone, use the keypad to enter
• Extension numbers
• Phone numbers (PSTN numbers).
Note: When you are dialing an extension or phone number on a 5312 IP Phone (only), do
not press the * and # keys. Press # to call the dialed number. Press * to delete the
last-entered digit.
5324 IP Phone
Depending on the context, the 5324 IP Phone’s keypad allows you to enter only numbers, or
numbers, letters, and some special characters. On the 5324 IP Phone, you can dial
• Extension numbers
• Phone numbers (PSTN numbers)
• IP addresses
- 10 -
Customizing Your Phone
• SIP URLs
• User ID names.
Letters correspond to those on the keypad, and characters to the table below. A flashing
cursor indicates the position of the character you are entering. The cursor automatically
advances after one second, or if you press a different keypad key.
To enter letters and special characters:
• Rapidly press the appropriate number key until the desired character appears on the
display.
To enter an uppercase letter:
• Press
mode.
(UP) before entering the letter. Press
(DOWN) to return to lowercase
To delete the character last entered:
• Press the <−−− softkey.
Table 2: Letter and Character Entry
Press
Dial Pad
Key
Once
1
1
space
?
!
2
2
a
b
c
3
3
d
e
f
4
4
g
h
i
5
5
j
k
l
6
6
m
n
o
7
7
p
q
r
8
8
t
u
v
9
9
w
x
y
z
0
0
+
&
%
$
\
“
*
*
.
=
:
/
;
,
–
#
#
@
(
)
[
]
<
>
Twice 3 Times 4 Times 5 Times 6 Times 7 Times 8 Times 9 Times
~
|
s
Ringer Control
To adjust the Ringer Volume while the set is ringing:
• Press
( UP ) or
( DOWN ).
To adjust the Ringer Volume while the set is idle:
1. Press
( SUPERKEY ), and then press ( >>) until FEATURES? appears.
2. Press OK, and then press ▼ until RINGER SOUNDS? appears.
3. Press OK. SET RINGER VOLUME? appears.
4. Press YES. The phone rings.
- 11 -
_
5312 and 5324 IP Phone SIP User and Administrator Guide
(UP) or
(DOWN) to adjust the volume to the desired level, and then
5. Press
press SAVE. SET RINGER VOLUME? appears.
6. Press NO. SET RINGER PITCH? appears.
7. Do one of the following:
• To return to the main menu, press NO.
• To return to the default display, press the programmed Superkey.
Handset Volume Control
To adjust the handset receiver volume when you are using the handset:
• Press
(UP) or
(DOWN).
Speaker Volume Control
To adjust the Speaker Volume when making an on–hook call or when listening to background
music:
• Press
(UP) or
(DOWN).
Display Contrast Control
To adjust the display contrast of your phone while idle:
• Press
(UP) or
(DOWN) while the phone is idle.
Note: If your phone loses power, the settings will return to the default settings.
Display Language
To set the display language:
1. Press the programmed Superkey, and then press >> FEATURES? appears.
2. Press OK, and then press ▼ until LANGUAGE? appears.
3. Press OK, and then press NO until the desired language appears.
4. Once the desired language appears, press YES. LANGUAGE? appears on the display.
5. Do one of the following:
• To return to the main menu, press EXIT.
• To return to the default display, press the programmed Superkey.
Personal Keys
Personal keys provide one-touch access to the following features:
• Speed Dial
• Shared Lines
• Line Keys (Administrator only)
• Call Logs
- 12 -
Customizing Your Phone
• Phonebook
• Forwarding
• Do Not Disturb
• Advisory Message
• PC Application (if applicable)
• Headset on/off
• RSS Feed (Web Feed)
Programming a Personal Key
You can program any Personal key that isn’t a prime line key. You can also modify or delete
the information programmed on any Personal key except Line 1 and Line 2.
Note: You cannot change your Personal keys settings while on a call.
Note: You can use the Web Configuration Tool to easily program, edit, and delete
programmable key information. For key programming settings, instructions, and phone
layouts, refer to the About the Key Programming Page topic in the Advanced Features
section of the Web Configuration tool online help. Also see Using Advanced Features
on page 25. Instructions for programming personal keys using the phone itself are
supplied in the following sections.
To program a Personal Key:
1. Press Superkey, and then press >>. FEATURES? appears.
2. Press OK, and then press ▼ until LANGUAGE? appears.
3. Press OK, and then press NO until the desired language appears.
4. Once the desired language appears, press YES. LANGUAGE? appears on the display.
5. Do one of the following:
• To return to the main menu, press EXIT.
• To return to the default display, press the programmed Superkey.
For information about programming shared line keys, see Shared Lines and Keys on page
29.
Line Keys
Line keys allow you to make and answer calls according to line or caller information. The
5324 IP Phone has four Line keys. The 5312 IP Phone has two Line keys. If one line is busy,
incoming calls are received on the next available Line key. Each phone has a pre-assigned
prime line (Line 1) key.
- 13 -
5312 and 5324 IP Phone SIP User and Administrator Guide
Pre-assigned Personal Keys
Your SIP phone has the following pre-assigned personal keys that cannot be changed:
Pre-assigned Value
Key Location
(Count from the bottom to top on the 5312 IP Phone, and from the
bottom to top in the right row on the 5324 IP Phone)
Line Keys (1 = Prime Line)
Key 1 - 4
Headset on/off
Key 10
Advisory Message
Key 11
Call Logs
Key 12
Speed Dial Keys
You can program a Personal Key as a Speed Dial key for one-touch dialing. See Using
Speed Dial Keys on page 17 for details. You can also store a personal number as a Speed
Dial.
Program a Speed Dial Key
To program a Speed Dial key:
(SUPERKEY), and then press >> until PROGRAM MEMORY KEYS?
1. Press
appears.
2. Press OK. SELECT A KEY appears.
3. Press the Personal key you wish to program. The associated programming information
appears on the display. If the key is not programmed, UNUSED KEY appears.
4. Do one of the following:
• If the selected key is currently programmed, press DEL (on a 5212) or DELETE (on a
5224) or EDIT. ENTER NUMBER appears.
• If the selected key is currently programmed as a different feature key, MDFY TO
SPEEDDIALKEY appears. Press YES to modify the key to a Speed Dial key. ENTER
NUMBER appears.
• If the selected key is not currently programmed, press ADDNEW. ENTER NUMBER
appears.
5. Do one of the following:
• If you want to enter a name, press NUMBER (on the 5312) or NAME (on the 5324)
• 5324 IP Phone only: If you want to enter a SIP URL or an IP address, press URL.
Note: Press <− − to delete characters.
6. Enter the destination information, and then press SAVE. KEY SAVED appears.
7. Press OK. PROGRAM MEMORY KEYS? appears.
8. Do one of the following:
• To program additional Speed Dials, press OK. SELECT A KEY appears.
• To return to the default display, press
(SUPERKEY).
9. Write the feature name on the designation card (see Elements of Your Phone on page 2).
- 14 -
Customizing Your Phone
Note: If the number you are calling requires an intermediate Long Distance Carrier number to
be dialed before the phone number, you can program a Speed Dial number for the Carrier.
After pressing the Speed Dial number for the carrier, wait for connection to the Carrier. When
connected, press the Speed Dial number for the party you are calling to send the DTMF
(touchtone signals) to the Carrier.
Note: If the Speed Dial number you want to program requires pauses (for example, if you
normally dial a main number, wait for a prompt, and then dial an extension) you can program
them into a Speed Dial key by entering a comma to represent a one-second pause. For
example, to dial main number 592-2122 and then enter extension 111 after a 3-second
pause, program a Speed Dial number as follows: 5922122,,,111.
Delete a Speed Dial Key
To delete a Speed Dial key:
(SUPERKEY), and then press >> until PROGRAM MEMORY KEYS?
1. Press
appears.
2. Press OK. SELECT A KEY appears.
3. Press the Personal key whose programming you want to delete. The associated
programming appears.
4. Press DEL (on a 5312) or DELETE (on a 5324). DELETE ITEM? appears.
5. Press YES. UNUSED KEY appears.
6. Do one of the following:
• To return to the main menu, press EXIT.
• To return to the default display, press
(SUPERKEY).
Programming Features in Speed Dial Keys
For Sylantro and Broadworks deployments, you can program any feature access codes that
require additional user input as Speed Dial keys. To access the feature directly, simply enter
the feature access code (for example, *67) as the Speed Dial number. To access the feature
and then have the phone wait for your manual input, enter the feature access code followed
by a semi-colon (for example, *67; ).
- 15 -
5312 and 5324 IP Phone SIP User and Administrator Guide
Making and Answering Calls
Making Calls
You can make and receive calls using the handset, headset or handsfree speaker. You can
dial by extension number or phone number, user ID name (5324 IP Phone only), SIP URL or
IP address (5324 IP Phone only), or IP address. You can also dial a Call Logs or Phonebook
entry.
If you are registered with a SIP Service Provider and want to dial a “regular” phone number,
your SIP Service Provider must provide access to the PSTN. To dial a SIP user name or
extension number, you must be registered with a SIP Service Provider. For more information,
contact your Administrator.
Dial by Number
1.
Lift the handset (optional).
2.
If you want to use a line other than Line 1, press a Line key.
3.
Do one of the following:
• Dial the number.
• Press a Speed Dial key.
• Press
4.
(REDIAL). (See Redial on page 17.)
Press DIAL or # (the pound key).
Dial by Name (5324 IP Phone only)
To dial by a user ID name, you must be registered with a SIP Service Provider.
1. Lift the handset (optional).
2. Press NAME.
3. Enter the name of the party you want to call.
Note:
If the name has more than 20 characters, only the last 20 characters appear on
the display.
4. Press DIAL or # (the pound key).
Dial by SIP URL or IP Address (5324 IP Phone only)
1. Lift the handset (optional).
2. Press URL, then enter the SIP URL or IP address of the party you want to call.
Note: If the SIP URL exceeds 20 characters, only the last 20 characters appear.
3. Press DIAL or # (the pound key).
- 16 -
Making and Answering Calls
Dial by Phone Book Entry
1. Press
(SUPERKEY), and then press >> until PHONE BOOK? appears.
2. Press OK. PHONE BOOK <number of items> appears on the display.
3. Press
(UP) and
(DOWN) to navigate to the entry you want to call.
4. Press DIAL or # (the pound key).
5. Lift the handset (optional).
Note: To dial from your Phone Book using the Web Configuration Tool, access the tool’s
Phone Book page (see Accessing the Web Configuration Tool on page 7).
Dial by Call Logs Entry
1. Press
(SUPERKEY), and then press >> until CALL LOGS? appears.
2. Press OK, and then press ▼ to navigate to the desired log type (Missed Calls,
Answered Calls or Outgoing Calls).
3. Press OK. The number of calls appears.
4. Press
(UP) and
(DOWN) to navigate through the logged call entries.
5. Press DIAL or # (the pound key). The log is dialed and the phone returns to the default
display.
6. Lift the handset (optional).
Redial
1. Lift the handset (optional).
2. Press
(REDIAL). The last number you dialed appears in the display.
3. Do one of the following:
•
Press the right-hand softkey to dial this number (5324 only).
•
(REDIAL) to scroll the list of previously-dialed numbers and then press
Press
the right-hand softkey to dial when the desired number is displayed.
Note: The redial list is maintained even after the phone reboots and is updated periodically.
If a power failure occurs during the update, it is possible that one or more previouslydialed numbers may be lost.
Using Speed Dial Keys
You may use Speed Dial Keys to make a call or to send a string of digits during a call (press
a Speed Dial Key during a call to send a multi–digit password, for instance).
To dial a stored Speed Dial number:
1. Lift the handset.
2. Press a Speed Dial key.
- 17 -
5312 and 5324 IP Phone SIP User and Administrator Guide
Note: If the number you are calling requires an intermediate Long Distance Carrier number to
be dialed before the phone number, you can program a Speed Dial number for the Carrier.
After pressing the Speed Dial number for the carrier, wait for connection to the Carrier. When
connected, press the Speed Dial number for the party you are calling to send the DTMF
(touchtone signals) to the Carrier.
Note: If the Speed Dial number you want to program requires pauses (for example, if you
normally dial a main number, wait for a prompt, and then dial an extension) you can program
them into a Speed Dial key by entering a comma to represent a one-second pause. For
example, to dial main number 592-2122 and then enter extension 111 after a 3-second
pause, program a Speed Dial number as follows: 5922122,,,111
Answering Calls
Incoming calls ring Line 1, if all lines are free, or the next available line. If all lines are busy
and Call Forward – Busy is not enabled (see Enable/Disable Call Forward on page 21),
callers hear a busy signal.
When the phone rings, the Ring/Message Indicator and the associated Line key flash, and
the name of the caller appears in the information area.
Answer a Call
To answer a call, do one of the following:
• For handset mode, lift the handset.
• For headset mode, press the Headset key, then press the flashing Line key.
• For handsfree mode, press
(SPEAKER) or press the flashing Line key.
For more information on handset, handsfree (Speaker) or headset calls, see Handset,
Handsfree and Headset Modes on page 27.
Auto Answer
You can use Auto Answer to automatically answer incoming calls in handsfree or headset
mode.
To enable or disable Auto Answer:
• Access the Feature Configuration page of the Web Configuration (see Accessing the
Web Configuration Tool on page 7).
To answer an Auto Answer call:
• Begin speaking when the call arrives.
To end an Auto Answer call, do one of the following:
(CANCEL).
• Press
• Wait for the caller to hang up.
- 18 -
Making and Answering Calls
Answer a Call Waiting
The 5324 IP Phone allows a maximum of three calls waiting while you are on a call. The
5312 IP Phone allows one call waiting. New calls wait on the next free line. When a new call
arrives, you hear a call waiting tone, the name of the new caller appears, and the
corresponding Line key flashes. If all lines are busy, callers hear a busy signal.
To answer a waiting call:
• Press the flashing Line key of the call waiting. The current call is put on hold, and you are
connected to the new caller.
To return to the original call:
• Press the associated flashing Line key.
Calling and Called Party Display
SIP phones display the true (programmed) identity of the called/calling party rather than the
standard number/name display.
- 19 -
5312 and 5324 IP Phone SIP User and Administrator Guide
Call Handling
Hold
The 5324 IP Phone supports a maximum of four held calls at the same time. The 5312 IP
Phone supports a maximum of two held calls.
When you place a call on hold, or when another party puts you on hold, the on-hold beep
reminds you that you are holding or on hold. If the handset is in its cradle, you hear the beep
through the handsfree speaker. You can turn off this beep, if desired.
Note: You cannot change your hold settings while on a call.
Hold a Call
• Press
(HOLD). The associated Line key flashes.
Retrieve a Call from Hold
• Press the associated flashing Line key. The Line key changes from flashing to lit solid.
Change On-Hold Settings
• Access the Feature Configuration page of the Web Configuration (see Accessing the
Web Configuration Tool on page 7).
Call Forward
Call Forward redirects incoming calls to your voice mailbox (by default) or to an alternate
number. Choose from the following Call Forward options:
• Call Forward – Always redirects all incoming calls
• Call Forward – No Answer redirects calls if you don’t answer after the programmed
number of rings (1 – 10)
• Call Forward – Busy redirects calls when all lines are busy.
All Call Forward options are OFF by default. You can turn on Call Forward No Answer and
Call Forward Busy at the same time.
Note: You cannot change your Call Forward settings while on a call.
Note: To program and enable or disable Call Forward using the Web Configuration Tool,
access the tool’s Feature Configuration page (see Accessing the Web Configuration
Tool on page 7).
Program Call Forward
1. Press
(SUPERKEY), and then press >> until FEATURES? appears.
2. Press OK. CALL FORWARDING? appears.
3. Press OK. FWD ALWAYS: <current status> appears.
- 20 -
Call Handling
4. Press ▼ to navigate to the desired Call Forward option.
5. Press OK to select the desired Call Forward option.
6. Press REVIEW. The current forwarding destination appears. If no forwarding is
programmed, the top line of the display is blank.
7. For Call Forward No Answer option only, press OPTIONS, enter the number of desired
rings (1 – 10) before a call is forwarded, and then press SAVE.
8. Press CHANGE, and then do one of the following:
• To enter a URL as the destination, press URL, and then enter the URL.
• To enter a name as the destination, press NAME, and then enter the name.
9. Press SAVE. After the information is saved, the same Call Forwarding option appears
on the display with its new status. Note: You can disable this display using the Display
Control section of the Feature Configuration page of the Web Configuration Tool.
10. Do one of the following:
• To return to the main menu, press EXIT.
• To return to the default display, press
(SUPERKEY).
Enable/Disable Call Forward
1. Press
(SUPERKEY), and then press >> until FEATURES? appears.
2. Press OK. CALL FORWARDING? appears.
3. Press OK. FWD ALWAYS: <current status> appears.
4. Press ▼ to navigate to the desired Call Forward option.
5. Once the desired Call Forwarding option appears, press TURNON or TURNOFF to
enable or disable the Call Forwarding option. The Call Forwarding option and its new
status appears on the display.
6. Press OK, and then press
(SUPERKEY) to return to the default display.
Call Transfer
You can transfer an active call to another party (one line must be free on your phone).The
5312/5324 IP Phone supports four lines. If all lines are busy on your phone, no calls can be
transferred.
Note: During a conference call, any party can perform a call transfer as long as there is one
free line on that phone. For conference call information, see Conference Call (ThreeWay) on page 22.
Transfer a Call to an Unconnected Third Party
1. While on a call, press
(TRANS/CONF). The call is put on hold.
2. Press a free Line key.
3. Call the party to whom you want to transfer the call, and then do one of the following:
- 21 -
5312 and 5324 IP Phone SIP User and Administrator Guide
• To talk to this party, wait until the connection is established, speak to the party,
press
(TRANS/CONF) or press the TRANSFR softkey (5324 only), and then
hang up. This is an Attended Call Transfer.
• To transfer the call without speaking to this party, immediately press
(TRANS/CONF) or press the TRANSFR softkey (5324 only), and then hang up.
The held call will be transferred to the call in progress. This is an Unattended Call
Transfer.
• To cancel the transfer, press
(CANCEL). You are returned to the held call.
Transfer a Call to a Third Party Already on Hold
1. While on a call, press
(TRANS/CONF). The call is put on hold.
2. Press the Line key of the call on hold, and then press
(TRANS/CONF).
3. Hang up.
Conference Call (Three-Way)
When two parties are connected on a call, either of those parties can originate a three-way
conference by adding a third party to the call in progress. Once three parties are connected,
no more parties can be added to that call.
A party can be involved in more than one three-way conference call at a time, but the calls
cannot be merged. For example, A and B are on a call. A adds C to create three-way
conference call ABC. B adds D to the call with A to make conference call ABD. ABC and ABD
remain separate– D is not added to conference call ABC.
Note: During a conference call, any party can perform a call transfer as long as there is one
free line on that phone. For call transfer information, see Call Transfer on page 21.
Add a Third Party to a Call in Progress
1. Press
(TRANS/CONF). The current call is put on hold.
2. Press a free Line key, and then do one of the following:
• Dial the number.
• Press a Speed Dial key.
• Press
(REDIAL).
3. Press DIAL.
4. Press the CONF softkey (or the # to select CONF on the 5312). The call you put on hold
in step 1 is connected to the call in progress.
Note: If the new party does not answer, press
party.
(CANCEL) twice to return to the held
Add a Party On Hold to a Call in Progress
1. Press
(TRANS/CONF). The current call is put on hold.
2. Press the Line key of the party already on hold.
- 22 -
Call Handling
(TRANS/CONF). The call put on hold in step 1 is connected to the call in
3. Press
progress.
Leave a Conference Call
Do one of the following:
• Hang up.
• Press HANGUP softkey (5324 IP Phone only).
• Press
(CANCEL).
Note: Any of the three parties can hang up and the other two parties will remain connected.
Messages - Advisory
An advisory message about your whereabouts appears on your caller's display.
Create an Advisory Message
• Access the Feature Configuration page of the Web Configuration Tool (see Accessing
the Web Configuration Tool on page 7).
Enable/Disable your Advisory Message
To enable or disable an advisory message:
1. Press
(SUPERKEY), and then press >> until FEATURES? appears.
2. Press OK, and then press ▼ until ADVISORY MESSAGES? appears.
3. Press OK. The first of several advisory messages appears.
4. Press
(UP) or
(DOWN) to navigate to the desired message.
5. Press TURNON or TURNOFF to enable or disable the message. When turned on, the
Advisory Message key is lit and the chosen advisory message will be displayed in the
LCD.
6. Do one of the following:
• To return to the main menu, press EXIT.
(SUPERKEY). The advisory message
• To return to the default display, press
alternates with the date and time on the default display.
Note: To enable/disable advisory messages using the Web Configuration Tool, access the
tool’s Feature Configuration page (see page 7).
Messaging – Voice Mail
Your Administrator configures your voice mail information so you can receive and access
voice mail messages. The Ring/Message Indicator flashes to indicate waiting messages.
Note: For administrative information on voice mail, see Error! Reference source not
found. on page Error! Bookmark not defined..
- 23 -
5312 and 5324 IP Phone SIP User and Administrator Guide
Access your Voice Mail Messages
1. Lift the handset (optional).
(MESSAGE)
2. Press
Note: The MESSAGE button must be configured by the Administrator (in Advanced
Webpage) to access the voice mail server.
3. Follow the voice mailbox prompts.
- 24 -
Using Advanced Features
Using Advanced Features
Do Not Disturb
Do Not Disturb (DND) forwards all calls directly to your voice mailbox so that a ringing phone
will not disturb you. If Do Not Disturb is enabled and you do not have a voice mailbox set up,
callers hear a busy signal.
Note: When Do Not Disturb is enabled, *DND ON* alternates with the date on the phone’s
display. If both Call Forward and Do Not Disturb are on, *DND ON* alternates with the
time on the display. Note: You can disable this display using the Display Control
section of the Feature Configuration page of the Web Configuration Tool.
Enable/Disable Do Not Disturb
1. Press
(SUPERKEY), and then press >> until FEATURES? appears on the display.
2. Press OK, and then press ▼ until DO NOT DISTURB? appears.
3. Press OK. DO NOT DISTURB <current status> appears.
4. Press TURNON or TURNOFF to enable or disable Do Not Disturb. After the information
is saved, DO NOT DISTURB <new status> appears.
5. Do one of the following:
• To return to the main menu, press EXIT.
• To return to the default display, press
(SUPERKEY).
Note: To enable or disable Do Not Disturb using the Web Configuration Tool, access the
tool’s Feature Configuration page (see Accessing the Web Configuration Tool on
page 7).
Call Logs
Call Logs keeps a record of your missed, answered and outgoing calls. The 5312/5324 IP
Phone logs the ten most recent missed, answered, and outgoing calls. The most recent call
appears at the top of each log.
Call Logs record party name, number, SIP URL or IP address, the call duration, and the time
and date of each call. When you have missed incoming calls, the number of calls missed
replaces the date on your phone’s display. Note: You can disable this display using the
Display Control section of the Feature Configuration page of the Web Configuration Tool.
Note: Call log information is saved automatically every 4 hours. If you reset your phone in
that 4-hour interval, any call logs generated during that time will not be stored.
View a Call Log Entry
1. Press
(SUPERKEY), and then press >> until CALL LOGS? appears.
- 25 -
5312 and 5324 IP Phone SIP User and Administrator Guide
2. Press OK, and then press ▼ to navigate to the desired log type (Missed Calls,
Answered Calls or Outgoing Calls).
3. Press OK. The number of calls appears.
4. Press
(UP) and
(DOWN) to navigate through the logged call entries.
5. When the desired entry appears, press DETAIL, and then press << and >> to view the
entry information.
6. When you have finished, press DONE.
7. Press
(SUPERKEY) to return to the default display.
Note: To view Call Log entries using the Web Configuration Tool, access the tool’s Call
Logs page (see Accessing the Web Configuration Tool on page 7).
Delete a Call Log Entry
Note: You can delete all entries in a Call log using the Delete All button on the Call Logs
page of the Web Configuration tool.
1. To delete selected entries in a call log: Press
CALL LOGS? appears on the display.
(SUPERKEY), and then press >> until
2. Press OK, and then press ▼ to navigate to the desired log type (Missed Calls,
Answered Calls or Outgoing Calls).
3. Press OK. The number of calls appears.
4. Press
(UP) and
(DOWN) to navigate through the logged call entries.
5. When the desired entry appears, press DELETE. CONFIRM DELETE? appears.
6. Press YES.to delete the selected log, or press DELETE ALL to delete all the call logs for
the log type selected.
7. Press
(SUPERKEY) to return to the default display.
Call a Call Logs Entry
• See Dial by Call Logs Entry on page 17 to quickly dial a Call Logs entry.
Call Forking
You can register your SIP ID with several SIP sets and have all configured sets ring
simultaneously. The indicator lamps of all configured aliases will flash until the call is
answered, and then all lamps except the answering set are extinguished. All Mitel SIP
phones support call forking.
- 26 -
Using Advanced Features
Handset, Handsfree and Headset Modes
Switch between Handset and Handsfree
To go from handset to handsfree mode:
1. Press
(SPEAKER).
2. Hang up the handset. Use the handsfree speaker to communicate with your party.
To go from handsfree to handset mode:
• Lift the handset, and use it to communicate with your party.
Switch between Handset and Headset
To go from handset to headset mode:
1. Press the Headset key. The Headset key light turns ON.
2. Hang up the handset. Use the headset to communicate with your party.
To go from headset to handset mode:
3. Lift the handset.
4. Press the Headset key. The Headset key turns OFF. Use the handset to communicate
with your party.
Switch between Headset and Handsfree
To go from headset to handsfree mode:
• Press the Headset key, and then press
(SPEAKER). The Headset key turns OFF.
Use the handsfree speaker to communicate with your party.
To go from handsfree to headset mode:
• Press the Headset key. The Headset key turns ON. Use your headset to communicate
with your party.
Muting a Call
To mute your phone so your party cannot hear you:
• Press
(MUTE). The
(MUTE) key turns ON.
To turn Mute off and return to the conversation:
• Press
(MUTE) again. The
(MUTE) key turns OFF.
- 27 -
5312 and 5324 IP Phone SIP User and Administrator Guide
Phone Book
The Phone Book is a scrollable list of contacts from which you can make a call. The 5312 and
5324 IP Phones hold a maximum of 60 Phone Book contacts.
Phone Book entries contain an automatic index number, the contact’s name (maximum of 20
characters) and a number, SIP URL, or IP address.
Note: To create, modify, or make calls from your Phone Book using the Web Configuration
Tool, access the tool’s Phone Book page (see Accessing the Web Configuration Tool
on page 7).
Note: You cannot change your Phone Book settings while on a call.
Create a Phone Book Entry
1. Press
(SUPERKEY), and then press >> until PHONE BOOK? appears.
2. Press OK. PHONE BOOK: <number of items> appears.
3. Press
appears.
(UP) and
(DOWN) to navigate through the entries until ENTRY EMPTY
4. Press ADDNEW. PROGRAM ADDRESS? appears.
5. Press YES, and then enter the IP address or SIP URL of the contact.
Note: Press <−−− to delete characters.
6. Press SUBMIT. After the information is saved, PROGRAM NAME? appears.
7. Press YES, and then enter the name of the contact.
8. Press SUBMIT. After the information is saved, the name of the contact appears.
9. Press
(SUPERKEY) to return to the default display.
Modify a Phone Book Entry
1. Press
(SUPERKEY), and then press >> until PHONE BOOK? appears.
2. Press OK. PHONE BOOK: <number of items> appears.
3. Press
(UP) and
(DOWN) to navigate to the entry you want to modify.
4. Press CHANGE, and then press EDIT. PROGRAM ADDRESS? appears.
5. Do one of the following:
• To modify an address or a SIP URL, press YES, enter the address or SIP URL,
and then press SUBMIT. After the information is saved, PROGRAM NAME?
appears.
• To modify a name, press NO. PROGRAM NAME? appears. Press YES, enter the
name, and then press SUBMIT. After the information is saved, the modified name
appears.
6. Press
(SUPERKEY) to return to the default display.
- 28 -
Using Advanced Features
Delete a Phone Book Entry
1. Press
(SUPERKEY), and then press >> until PHONE BOOK? appears.
2. Press OK. PHONE BOOK: <number of items> appears.
3. Press
(UP) and
(DOWN) to navigate to the entry you want to delete.
4. Press CHANGE, and then press DELETE. CONFIRM DELETE? appears.
5. Press CONFIRM. The entry is deleted, and ENTRY EMPTY appears.
6. Press
(SUPERKEY) to return to the default display.
Call a Phone Book Entry
• See Dial by Phone Book Entry on page 17 to call a Phone Book entry
Shared Lines and Keys
There are three types of shared lines:
•
SIP: basic shared line with limited features (supports call forking but does not have
LED activity and lines are not linked. This type of shared line is available in normal
SIP mode).
• SIP_BLA line type: server-enhanced Sylantro Bridged Line Appearance line type
• SIP_SCA line type: server-enhanced Broadworks Shared Call Appearance line type
BLA and SCA line types allow calls and lines to be shared by multiple users. A SIP server
provides support for call presentation to multiple phones, call state notifications, and access
control.
Shared lines are shared among users but only the user who initiates activity on the line has
full control over it. For example, if a user initiates a conversation on a shared line, other users
can not affect that conversation. If the shared line is Ringing, or on Hold, any share user can
pick up the line and be connected to the calling/held party.
An exception to this scenario occurs when the server is configured to allow line seizure by
multiple lines. Mitel SIP phones support multi-call server programming.
Requirements for making calls and picking up held calls from shared lines are the same as
normal (non-shared) lines.
Shared Line Programming Requirements:
• Your Administrator must create a user entry (on the User List Config page of the Web
Configuration tool) for the user with whom you want to share a line.
• Your Administrator must configure the type of shared line (SIP, BLA, or SCA) in the Line
Type field on the User List Config page.
Programming Shared Line Keys
1. Access the Key Programming page of the Web Configuration Tool.
2. Click the Key Number of the key you want to assign as a shared line.
- 29 -
5312 and 5324 IP Phone SIP User and Administrator Guide
3. From the Feature list, select Shared Line.
4. From the Context list, select the User ID with which to associate this key.
5. Enter a label/description for this key (optional).
6. Click Apply to apply the changes.
Line Key Status
Shared lines display the following indicator lamps:
Line
Status
LED
Appearance
Description
Trying
Solid Red
When a user initiates a call on a shared line, the
LED of that line and all shared lines glows red.
Active
Solid Green
When a call has been successfully connected, the
LED of that line and all shared lines glows green.
Held
Flashing Red
When a user puts another party on hold, the LED of
that line and all shared lines flashes red.
Alerting
Flashing Green
When a call is incoming, the LED of the called line
and all shared lines flashes green.
RSS (Web) Feed
RSS feeds are text formats used to deliver information such as News and weather reports.
Your Mitel SIP Phone can act as an RSS feed reader, displaying the feed on Line 1 of the
phone display when the phone is idle. You can program one or more keys on your phone to
display a web feed or to display your own customized message (branding). Use the Key
Programming Page in the Web Configuration Tool to program one or more RSS Feed keys.
For more information, refer to the Web Configuration Tool Online Help.
Enable/Disable RSS Feed
Once an RSS Feed key is programmed, press the key to display the feed. The LED on the
key will light up and remain lit while the RSS feed scrolls continuously across Line 1 of your
phone display. Press the key again to stop the feed.
Note: If your Administrator has programmed a global RSS feed or branding message for
your phone, this text will be displayed when your phone is idle. When one of your own
personal RSS Feed keys is enabled, it will override any global feed set by your
Administrator for your phone.
Tip:
To improve RSS readability, you can disable other displays (like Call Forwarding and
Missed Calls). Use the Feature Configuration page of the Web Configuration Tool to
set Display Controls.
Time and Date
A Simple Network Time Protocol (SNTP) server (version 4 or later) provides your phone with
the date and time. Your Administrator configures your time zone once using the Web
Configuration Tool. Your phone automatically adjusts to Daylight Savings.
- 30 -
Using Advanced Features
If an SNTP server is not available in your system setup, you can modify the time and date
using your phone or the Date/Time page of the Web Configuration Tool (see Accessing the
Web Configuration Tool on page 7). For more information, contact your Administrator.
Note: You cannot change your time and date settings while on a call.
Note: If your phone loses power, the modified time and date are not saved.
Change the Time and Date
Important: Use this procedure only if an SNTP server is not provided. If an SNTP server is
not available, you must reprogram these settings every time the phone reboots.
1. Press
(SUPERKEY), and then press >> until FEATURES? appears.
2. Press OK, and then press ▼ until TIME AND DATE? appears.
3. Press OK. SET TIME? appears.
4. Do one of the following:
• To change the time, press YES. 12 OR 24 HR FORMAT? appears. Proceed to
step 5.
• To change the date, press NO. SET DATE? appears. Proceed to step 9.
5. Do one of the following:
• To enter the time in a.m./p.m. format, press 12.
• To enter the time using the 24-hour clock, press 24.
6. Enter the time (for example, 1236 for 12:36; 0220 for 02:20), and then press SUBMIT.
7. (For a.m./p.m. only) Press AM or PM. SET TIME? appears with the new time.
8. Press NO. SET DATE? appears.
9. Do one of the following:
• To change the date, press YES, and then proceed to step 10.
• To return to the main menu, press NO, and then proceed to step 11.
10. Enter the date (for example, enter 161204 for 16 December 2004), and then press
SUBMIT. SET DATE? appears with the new date.
11. Do one of the following:
• To return to the main menu, press NO.
• To return to the default display, press
- 31 -
(SUPERKEY).
5312 and 5324 IP Phone SIP User and Administrator Guide
Administrator Tools
This section is the SIP Administrator’s reference to Superkey menu interface configuration
options. Where applicable, it references the appropriate page(s) of the Web Configuration
Tool.
Note: Some procedures can only be completed from the Web Configuration Tool.
To access the referenced pages of the Web Configuration Tool, see Accessing the Web
Configuration Tool (page 7).
To get help with settings and programming for administrative procedures, see Accessing the
Web Configuration Tool Online Help (page 7).
SIP Administrator Phone Passwords
To log in for the first time as an Administrator, use the default administrator name and
password. Change these passwords as soon as possible to prevent unauthorized changes to
the phone.
For privacy reasons, an asterisk ( * ) appears for each character you enter.
Table 3: Default Administrator User Names and Passwords
Phone
Default
Administrator Name
Default Administrator
Password
5312 IP Phone
admin
5312
5324 IP Phone
admin
5324
Change Phone Passwords
To change user or administrator passwords:
• Access the Users & Passwords page of the Web Configuration Tool.
SIP User Accounts
A SIP user account includes a user name and password, and allows the user to register with
the SIP Service Provider.
Configure/Modify a SIP User account
Access the Configuring Users and SIP Server Providers topic in the Administrator's Web
Configuration Tool online help.
- 32 -
Administrator Tools
View a User Name
1. Press
(SUPERKEY).
2. Press the third Personal key (counting upwards from the bottom on the 5312 IP Phone)
or the Line 3 key (counting upwards from the bottom right on the 5324 IP Phone). The
user display name (top) and user name (bottom) appears.
3. Press
(SUPERKEY) to return to the default display.
Device Parameters
To view the software version and the MAC address:
1. Press
display.
(SUPERKEY), and then press >> until ADMIN TOOLS? appears on the
2. Press OK. DEVICE PARAMETERS? appears.
3. Press OK. SOFTWARE VERSION appears.
4. Press Next to view either the software version or the MAC address.
• To view the software version, press REVIEW (the current software version
appears), then press OK. SOFTWARE VERSION reappears.
• To view the MAC address, press NEXT (MAC ADDRESS appears), then press
REVIEW. The current MAC address appears. Press OK. MAC ADDRESS
reappears.
5. Do one of the following:
• To return to the DEVICE PARAMETERS? menu, press EXIT.
• To return to the default display, press
(SUPERKEY).
Note: You can also view the MAC address using the Line 1 key (see View the IP and MAC
Addresses on page 34). You can also view the firmware version using the Line 2 key
(see View the Firmware Version on page 35).
Protocols
For information about supported communication and media protocols, access the Configuring
Protocols topic of the Administrator’s Web Configuration Tool Online (see Accessing the Web
Configuration Tool Online Help on page 7).
Enable/Disable Protocols
To enable/disable protocols using the Web Configuration Tool:
• Access the tool’s Protocols page.
Note: To access the Web Configuration Tool, HTTP must be enabled. If HTTP is disabled
and you need to access the tool, enable HTTP through the Superkey Menu Interface
(see procedure that follows below).
To enable/disable protocols using the Superkey Menu Interface:
- 33 -
5312 and 5324 IP Phone SIP User and Administrator Guide
1. Press
display.
(SUPERKEY), and then press >> until ADMIN TOOLS? appears on the
2. Press OK, and then press ▼ until ACCESS PROTOCOLS? appears on the display.
3. Press OK, enter your administrator password, and then press SUBMIT. HTTP <current
status> appears on the display.
4. Do one of the following:
• To enable HTTP, press TURNON.
• To disable HTTP, press TURNOFF.
• To enable or disable TFTP, press NEXT.
5. Repeat steps 3 and 4 for TFTP, Telnet, SNMP and SRTP. After you enable or disable a
protocol, that protocol and its new status appears on the display.
6. Do one of the following:
• To return to the main menu, press EXIT.
• To return to the default display, press
(SUPERKEY).
SRTP Call Encryption Indicator
For information about the Call Encryption setting, see Call Encryption Indicator on page 7.
Also refer to the Configuring Protocols topic of the Administrator’s Web Configuration Tool
Online Help (see page 7).
Viewing/Modifying the Network Settings
View the IP and MAC Addresses
To view the phone’s IP and MAC addresses:
1. Press
appear.
(SUPERKEY), and then press the Line 1 key. The IP and MAC addresses
2. Press
(SUPERKEY) to return to the default display.
Modifying Network Settings
To modify network settings using the Web Configuration Tool:
• Access the Configuring Network Settings topic of the Administrator's Web Configuration
Tool online help.
To modify network settings using the Superkey Menu Interface
1. Press
display.
(SUPERKEY), and then press >> until ADMIN TOOLS? appears on the
2. Press OK, and then press ▼ until NETWORK SETTINGS? appears.
3. Press OK, enter your administrator password, and then press SUBMIT.
4. Press NEXT until the network configuration settings you want to change appear.
- 34 -
Administrator Tools
5. Press REVIEW to view the current settings of the selected setting, and then do one of
the following:
• (Optional) To enable or disable DHCP, press TURNON or TURNOFF.
• To change a value, press CHANGE, enter the new value, and then press SUBMIT.
After the information is saved, the next setting appears.
• To leave a value as it is, press EXIT or NEXT.
6. Repeat steps 4 and 5 until all desired changes have been made.
7. Press
(SUPERKEY) to return to the default display.
8. For the settings to take effect, reboot the phone (i.e. unplug the power source from the
phone, and then plug the power source back in).
Upgrade the Phone’s Firmware
IMPORTANT: If you are upgrading from a previous load, please ensure you are following the
correct upgrade procedure as outlined in the latest product Release Notes available from the
SIP Software Download Page. The SIP Software Download Page provides access to the
latest SIP firmware loads, upgrade procedures, and Release Notes.
To access the latest SIP firmware loads, upgrade procedures, and Release Notes:
1. In your browser, go to www.mitel.com, click Login, and log in to Mitel OnLine.
2. Move your cursor over Products and Services, and select SIP Desktop Devices.
3. In “Related Links” click SIP Software Download Page for firmware loads or Product
Documentation to access the SIP documentation.
For detailed information about firmware upgrades:
• Access the About the Firmware Updates Page topic in the Administrator’s Web
Configuration Tool Online Help (see page 7).
View the Firmware Version
To view the firmware version using the Web Configuration Tool:
• Access the Home Page of the Web Configuration Tool and click Firmware Updates.
Firmware version is also available on the top left corner of Home page.
To view the firmware version using the Superkey Menu Interface:
1. Press
(SUPERKEY).
2. Press the Line 2 key. Both the main and boot firmware versions appear on the display.
3. Press
(SUPERKEY) to return to the default display.
Upgrading the Firmware
To upgrade the firmware using the Web Configuration Tool:
• Access the Configuring Network Settings and Updating Firmware sections of the
Administrator's Web Configuration Tool.
- 35 -
5312 and 5324 IP Phone SIP User and Administrator Guide
To upgrade the phone’s firmware through the Superkey Menu Interface:
1. Press
(SUPERKEY), and then press >> until FEATURES? appears.
2. Press OK, and then press ▼ until UPGRADE FIRMWARE? appears.
3. Press OK. CHOOSE PROTOCOL appears.
4. Press the desired protocol (HTTP or TFTP), or press AUTO. BEGIN UPGRADE NOW?
appears.
5. Press CONFIRM. The downloading process begins and the phone reboots. This
process may take approximately 1 to 2 minutes. When the time and date appear on the
display, the download and reboot is complete and the phone is ready for use.
CAUTION: DO NOT remove power from the phone while phone is upgrading its
memory with the new firmware. This may result in severe damage to your phone.
Troubleshooting Tip: If your phone displays "SIP MAIN NOT FOUND", it is likely that
your system has experienced a power failure. The SIP Phone Boot firmware "borrows" Flash
sectors from the SIP Main area during firmware installation. At the end of a normal
installation, the sectors are restored without affecting SIP Main. However, if power is
removed during Boot installation, then SIP Main is erased and will have to be reinstalled on
the phone.
Automating Firmware Upgrades
You can configure phones to poll the server for new versions of firmware. When the phone
detects a firmware upgrade, it downloads the new version and stores it in memory. When it is
next idle, the phone reboots with the new firmware.
To automate firmware upgrades, your Administrator can set a Firmware Upgrade option and
a polling interval on the Firmware Update page of the Web Configuration Tool. For
programming options, refer to the online help supplied with the Web Configuration Tool.
To upgrade firmware on multiple phones, refer to the Mass Deployment topic in the
Administrators Tools section of the Web Configuration Tool Online Help.
Configuring Voice Mail
Voice mail for SIP-supported phones is server-based. For more information on the voice mail
system, contact the SIP Service Provider.
To configure voice mail on the 5312 IP Phone and 5324 IP Phone:
• Access the Administrator Tools > Configuring SIP Features section in the Administrator’s
Web Configuration Tool online help.
To configure voice mail on a 5324 IP Phone only:
1. Press
(SUPERKEY), and then press >> until ADMIN TOOLS? appears.
2. Press OK, and then press ▼ until NETWORK SETTINGS? appears.
3. Press OK, enter your administrator password, and then press SUBMIT.
4. Press NEXT until VOICE MAIL SERVER appears, and then press REVIEW.
- 36 -
Administrator Tools
5. Press CHANGE, enter the IP address of the voice mail server, and then press SUBMIT.
After the information is saved, VOICE MAIL SERVER appears.
6. Press NEXT. VOICE MAIL PORT NUM appears.
7. Press REVIEW, and then press CHANGE.
8. Enter the voice mail port number, and then press SUBMIT. After the information is
saved, VOICE MAIL PORT NUM appears.
9. Do one of the following:
• To return to the main menu, press EXIT.
• To return to the default display, press
(SUPERKEY).
Adjust Daylight Savings
Access the Administrator Tools > Configuring Network Settings topic in the Administrator’s
Web Configuration Tool online help.
Configuration Files
The 5312 and 5324 IP Phones support configuration files for automatic programming. For
more information about the configuration files, and about configuring multiple phones, access
the Administrator Tools > Phone Management topic in the Administrator’s Web Configuration
Tool online help.
Hot Line
When a Hot Line number, SIP URL or an IP address is set up, the 5312 or 5324 IP Phone
automatically dials that number or address when taken off-hook.
For Hot Line programming instructions, access the Administrator Tools > Configuring SIP
Features section in the Administrator’s Web Configuration Tool online help.
Media Configuration
For programming instruction, access the Administrator Tools > Configuring Media Settings
topic in the Administrator’s Web Configuration Tool online help.
Main Program and Boot Program Configuration Options
For information about additional configuration options available through the phone’s main
program (Superkey menu interface) or boot program:
• Access the Administrator Tools > Configuring in the Main and Boot Programs topic in the
Administrator’s Web Configuration Tool online Help.
Global RSS Feed
You can program a global RSS feed or branding message that will be displayed on Line 1 of
Mitel SIP Phones when the phones are idle. Program the global RSS feed in the Advanced
- 37 -
5312 and 5324 IP Phone SIP User and Administrator Guide
Features section of the Web Configuration Tool. For more information, refer to the Web
Configuration Tool Online Help.
- 38 -
Specifications
Specifications
For a complete list of supported features (including Sylantro and Broadsoft features) and
supported RFCs, access the Specifications topic in the Web Configuration Tool online help.
Glossary
Term
Definition
DHCP
Dynamic Host Configuration Protocol
HTTP
Hypertext Transfer Protocol
HTTP
Hypertext Transfer Protocol
ID
Identification
IP
Internet Protocol
LAN
Local Area Network
MAC
Media Access Control
PSTN
Public Switched Telephone Network
RSS
Really Simple Syndication
SIP
Session Initiation Protocol
SNMP
Simple Network Management Protocol
SNTP
Simple Network Time Protocol
SRTP
Secure Real-time Transport Protocol
TFTP
Trivial File Transfer Protocol
URL
Uniform Resource Locator
VLAN
Virtual LAN
- 39 -
10.
Download PDF