American DJ | Pocket Scan | Operating instructions | American DJ Pocket Scan Operating instructions

American DJ
®
Pocket Scan™ Introduction
General instructions: To optimize the performance of this product,
please read these operating instructions carefully to familiarize yourself
with the basic operations of this unit. These instructions contain important safety information regarding the use and maintenance of this unit.
Please keep this manual with the unit, for future reference.
Unpacking: Thank you for purchasing the Pocket Scan™ by Ameri-
can DJ®. Every Pocket Scan™ has been thoroughly tested and has
been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your fixture for any
damage and be sure all accessories necessary to operate the unit has
arrived intact. In the case damage has been found or parts are missing, please contact our toll free customer support number for further
instructions. Do not return this unit to your dealer without first contacting
customer support.
Introduction: The Pocket ScanTM is part of American DJ’s continu-
ing pursuit for creating high quality affordable intelligent fixtures. The
Pocket ScanTM is our most compact full featured scanner ever. The
Pocket Scan™ is a DMX scanner with a built-in 4.9mW diode laser.
Both the laser and the lamp can be operated at the same time for truly
amazing effects. This unit is light weight and compact which makes it a
great piece for mobile DJ’s and clubs. For best results use this unit with
a fog machine to enhance the output of the beams and laser.
Customer Support: American DJ® provides a toll free customer sup-
User Instructions
Rev 10/09
port line, to provide set up help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.americandj.com for any comments or
suggestions. Service Hours are Monday through Friday 9:00 a.m. to 5:
00 p.m. Pacific Standard Time.
Voice:
(800) 322-6337
Fax: (323) 582-2610
E-mail: support@americandj.com
To purchase parts online visit http://parts.americandj.com
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
American DJ®.
©American
DJ Supply® - www.americandj.com - Pocket Scan™ Instruction Manual Page 2
Pocket Scan™ Quick Start
Quick Start Stand Alone Mode
Connect all your units together via the XLR connector. You can
connect up to 16 units together in Master/Slave mode. The master
unit will run the slaves to the masters built in programs and internal
microphone. Plug in all units. When the Pocket Scan™ is first turned
on, it will run through an internal self test where it moves all motors to
their zero position. After the self test the units will react to sound, and
chase to the several built in programs.
Pocket Scan™ • Scanner and Laser in one effect
• 4.9mW diode laser
• 15 colors plus white
• Split colors
• 13 gobos plus spot
• Separate color and gobo wheels
• High Speed Shutter with variable Speed
• 170 degree pan / 110 degree tilt
• Full Micro-stepping, with 4 stepper motors.
• Built in Microphone
• Auto switch to Stand-Alone (Master/Slave) operation
when DMX signal is disconnected
• Run up to 16 heads without controller
• DMX-512 protocol
• Full Focusing
• Fan cooled
• Uses 4 DMX Channels
• Digital DMX display
Features
Pocket Scan™ Warranty Registration
The Pocket Scan™ carries a one yeare (365 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase.
All returned service items whether under warranty or not, must be
freight pre-paid and accompany a return authorization (R.A.) number.
If the unit is under warranty you must provide a copy of your proof
of purchase invoice. Please contact American DJ® customer support
for a R.A. number.
©American
DJ Supply® - www.americandj.com - Pocket Scan™ Instruction Manual Page 3
Pocket Scan™
!
Safety Precautions
DANGER
VISIBLE LASER RADIATION
-AVOID DIRECT EYE EXPOSURE
LASER DIODE
WAVELENGTH : 532 nm
Max Output : <4.9mW
Class IIIa Laser Product
!
CAUTION IMPORTANT! When installing this projector, make sure
that it is mounted in a manner that prevents the audience from
looking directly into the beam, and the beam from striking the
audience.
Safety Issue: This unit may blow a fuse if the maximum allotted load
of 2 amps is reached. If the fuse needs replacement, please see the
fuse replacement guidelines on page 13.
•To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture
•Do not spill water or other liquids into or on to your unit.
•Be sure that the local power outlet match that of the required voltage
for your unit.
•Do not attempt to operate this unit if the power cord has been frayed
or broken. Do not attempt to remove or break off the ground prong
from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short.
•Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
•Never operate this unit when it’s cover is removed.
•Never plug this unit in to a dimmer pack
•Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
•Do not attempt to operate this unit, if it becomes damaged.
•This unit is intended for indoor use only, use of this product outdoors
voids all warranties.
•During long periods of non-use, disconnect the unit’s main power.
•Always mount this unit in safe and stable matter.
•Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, ©American
DJ Supply® - www.americandj.com - Pocket Scan™ Instruction Manual Page 4
Pocket Scan™
Safety Precautions
paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 14 for cleaning details.
•Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.
•The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a
marked change in performance.
Pocket Scan™
Laser Warnings and Safety
NON-INTERLOCKED HOUSING WARNING
The Pocket Scan™ contains high power laser devices internally. Do
not open the laser housing, due to the potential exposure to unsafe
levels of laser radiation. The laser power levels, if the unit is opened,
can cause instant blindness, skin burns and fires.
STOP AND READ ALL LASER SAFETY DATA
OPERATION INSTRUCTIONS AND LASER SAFETY
The light source emitted from this product can potentially cause eye
injury if not set up and used properly. The light source emitted from
a laser is very different from any other light sources with which you
may be aware of. Laser light is thousands of times more concentrated
than any light from any other kind of light source. This concentration
of light can cause instant eye injuries, primarily by burning the retina
(the back of your eyeball contatining cells that are sensitive to light).
Even if you cannot feel “heat” from a laser beam, it can still potentially
injure or blind you or your audience. Even very small amounts of laser
beam light are potentially hazardous even at long distances. Laser
eye injuries can be sustained faster than you can blink.
Do not think that because this laser splits the laser beam into hundreds of beams and that the laser beam is scanned out in high speed,
that an individual laser beam is safe for eye exposure. This laser uses
dozens of milliwatts of laser power (Class 3B levels internally) before
it splits into multiple beams (Class 3R levels). Many of the individual
beams are potentially hazardous to the eyes.
Do not that because the laser light is moving, it is safe. This is not
true. Nor, do the laser beams always move. Since eye injuries can
occur instantly, it is critical to prevent even the smallest possibility of
any direct eye exposure. In the laser safety regulation, it is not legal
to aim Class 3R lasers in areas which people can get exposed. This is
true even if it is aimed below people’s faces, such as on a dance floor.
Do not operate the laser without first reading and understanding
all safety and technical data in this manual.
Always set up and install all laser effects so that all laser light is at
least 3 meters (9.8 feet) above the floor on which people can stand.
©American
DJ Supply® - www.americandj.com - Pocket Scan™ Instruction Manual Page 5
©American
DJ Supply® - www.americandj.com - Pocket Scan™ Instruction Manual Page 6
Pocket Scan™
Laser Warnings and Safety
After setting up, and before public use, test laser to ensure proper
function. Do not use if any defect is detected. Do not use if laser
emits only one or two laser beams rather than dozens/hundreds, as
this could indicate damage to the diffraction grating optic, and could
allow emission of higher laser levels above Class 3R.
Pocket Scan™
Warning Labels
Do not point lasers at people or animals. Never look into the laser
aperture or laser beams.
Do not point lasers in areas in which people can potentially get
exposed, such as uncontrolled balconies, etc.
Do not point lasers at highly reflective surfaces, such as windows,
mirrors and shiny metal. Even laser reflections can be hazardous.
Never point a laser at aircraft, this is a federal offense.
Never point un-terminated laser beams into the sky.
Do not expose the output optic (aperture) to cleaning chemicals.
Do not use laser if the laser appears to be emitting only one or two
beams.
Do not use the laser if the housing is damaged, the housing is open,
or if the optics appear damaged in any way.
Never open the laser housing. The high laser power levels inside of
the protective housing can start fires, burn skin and will cause instant
eye injury.
Never leave this device running unattended.
The operation of a class 3R laser show is only allowed if the show
is controlled by a skilled and well- trained operator, familiar with the
data included in this manual.
The legal requirements for using laser entertainment products vary
from country to country. The user is responsible for the legal requirements at the location/country of use.
Always use proper lighting safety cables when hanging lights and
effects overhead.
©American
DJ Supply® - www.americandj.com - Pocket Scan™ Instruction Manual Page 7
©American
DJ Supply® - www.americandj.com - Pocket Scan™ Instruction Manual Page 8
POWER
Pocket Scan™
Set Up
Power Supply: Before plugging your unit in, be sure the source voltage in your area matches the required voltage for your American DJ®
Pocket Scan.™ The American DJ® Pocket Scan™ is available in a 120v
and 220v version. Because line voltage may vary from venue to venue,
you should be sure your unit voltages matches the wall outlet voltage
before attempting to operate you fixture.
Pocket Scan™
Set Up
DMX512
DMX+,DMX-,COMMON
Notice: Be sure to follow figures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
COMMON
DMX-512: DMX is short for Digital Multiplex. This is a universal proREMOTE
CONTROL
INPUT
INPUT
OUTPUT
REMOTE
CONTROL
SOUND
DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a single
controller, as long as all fixtures and the controller are DMX compliDMX512
ant. To ensure proper DMX data transmission,
when
using several
DMX+,DMX-,COMMON
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX COMMON
address
of 1, the DMX controller knows to send DATADMX512
assigned
to address
DMX +1 to
OUT
3-PIN XLR
DMX that unit, no matter where it is located in the DMX
chain.
2
3
Data Cable (DMX Cable) Requirements (For DMX and Master/
Slave Operation): The Pocket Scan™ can be controlled via DMX-512
protocol. The American DJ® Pocket Scan™ is a four channel DMX unit.
The DMX address is set on the front panel of the Pocket Scan™. Your
unit and your DMX controller require a standard
3-pin XLR connector for data input and data output
(Figure 1). If you are making your own cables, be
sure to use standard two conductor shielded cable
(This cable may be purchased at almost all pro
sound and lighting stores). Your cables should be
made with a male and female XLR connector on
either end of the cable. Also remember that DMX
Figure 1
cable must be daisy chained and can not be split.
©American
DJ Supply® - www.americandj.com - Pocket Scan™ Instruction Manual Page 9
INPUT
2
1 Ground
DMX +
3
OUTPUT
3
DMX -
1
2
SOUND
2 Cold
2 Cold
DMX512 IN
3-PIN XLR
3
Figure 2
XLR Female Socket
XLR
Male Socket
INPUT
1 Ground
REMOTE
CONTROL
INPUT
INPUT
1
2
Termination redu
avoids signal tra
and interference.
to connect a DMX
120 Ohm 1/4 W)
and PIN 3 (DMX
OUTPUT
XLR Pin Configuration
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
3 Hot
Figure 3
POWER
1
1
DMX512 OUT
3-PIN XLR
tocol used as a form of communication between intelligent fixtures and
controllers. A DMX controller sends DMX data instructions from the
controller to the fixture. DMX data is sent as serial data that travels
from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).
SOUND
POWER
3 Hot
Pin 3 = Data True (positive)
POWER
POWER
Special Note: Line Termination. When longer runs of cable are
3
1
2
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
Termination reduces signal errors and
DMX512 IN
3-PIN XLR
3
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
Figure 4
5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR
connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures
may be implemented in a 3-pin XLR DMX line. When inserting standard
5-pin XLR connectors in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor
3-Pin XLR Female (Out)
5-Pin XLR Male (In)
Ground/Shield
Pin 1
Pin 1
Data Compliment (- signal)
Pin 2
Pin 2
Data True (+ signal)
Pin 3
©American
Pin 3
Not Used
Do Not Use
Not Used
Do Not Use
DJ Supply® - www.americandj.com - Pocket Scan™ Instruction Manual Page 10
Pocket Scan™
Operating Instructions
CAUTION IMPORTANT! When installing this projector, make sure
that it is mounted in a manner that prevents the audience from
looking directly into the beam, and the beam from striking the
audience.
Pocket Scan™
Operating Instructions
Operating Modes:
You can use the Pocket ScanTM in three ways:
• Stand alone mode - The unit will react to sound, chasing through the several built in programs. You can also use the optional
Pocket Scan/RF Remote Control to set blackout, strobe or slow scan mode.
• Master/Slave mode - You can daisy chain up to 16 units together to get a synchronized light show that will react to sound chasing through several built in programs.
• DMX control mode - This function will allow you to control each indi-
vidual fixtures traits with a standard DMX 512 controller such as the American DJ Show Designer.TM
Stand Alone Mode:
The Pocket ScanTM has a sophisticated built-in light show that will run
to sound when there is no DMX signal present. Plug the fixture in and
it will chase through its programs via sound. You can also use the
optional remote to blackout, strobe, or slow scan the units.
Master-Slave Operation:
This function will allow you to link up to 16 units together to run in a
Master-Slave mode. In Master-Slave operation one unit will act as the
controlling unit and the others will react to the controlling units built-in
programs. Any unit can act as a Master or as a Slave however, units
must be programmed to act as “Masters” or as “Slaves.” There are
two Master-Slave modes, Fast and Slow.
Master-Slave Connections:
1. Daisy chain your units via the XLR connector on the top of the unit. Use standard XLR microphone cables to link your units to-
gether. Remember that the Male XLR connector is the input and the Female XLR connector is the output. The first unit in the chain (master) will use the female XLR connector only. The last unit in the chain will use the male XLR connector only.
©American
DJ Supply® - www.americandj.com - Pocket Scan™ Instruction Manual Page 11
Pocket Scan™ LCD
100
10
1
Setting Units as Masters or Slaves:
This section will detail the procedure for switching units between
Masters and Slaves. Each unit can function as a “Master” or as a
“Slave” To adjust the settings:
1. Be sure the main power switch is set to the “OFF” position.
2. With the power off press and hold down the LCD “100-Key,”
and turn the power on.
3. When the power is applied, the LCD will display the current
DMX address and then display the current Master-Slave
mode. Master-Slave modes will be displayed as followed:
“S-F” will equal Master/Send Fast Mode
“S-S” will equal Master/Send Slow Mode
“rEC” will equal Slave/Recieve Mode
4. To toggle between Master and Slave mode repeat steps one
and two.
Adjusting the Speed of the internal Program:
This section will detail the procedure for changing the Master Unit
operating mode. The master mode may be changed to operate in Fast
or Slow modes.
1. Be sure your unit is in Master mode, see Setting Units as
Masters or as Slaves, above.
2. Be sure the main power switch is set to the “OFF” position.
3. With the power off press and hold down the LCD “10-Key,”
and turn the power on.
4. When the power is applied, the LCD will display the current
DMX address and then display the current Master-Slave
mode. Master-Slave modes will be displayed as followed:
©American
DJ Supply® - www.americandj.com - Pocket Scan™ Instruction Manual Page 12
Pocket Scan™
Operation Cont.
“S-F” will equal Master/Send Fast Mode
“S-S” will equal Master/Send Slow Mode
4. To toggle between Fast and Slow modes repeat steps one
and two.
Note: The remote control only operates in Stand-Alone or MasterSlave modes. If the remote is used while the units are in DMX mode,
the remote will not function. If the unit does not receive an active DMX
signal, the unit will automatically react to sound in the Master/Slave
mode.
DMX Mode:
Operating through a DMX controller give the user the freedom to create their own programs tailored to their own individual needs. This
function also allows you to use your fixtures as spot lights.
1. This function will allow you to control each individual fixture’s
traits with a standard DMX 512 controller such as the
American DJ® Show Designer™ or the American DJ® DMX Operator.™
2. The Pocket ScanTM uses seven DMX channels to operate;
Channel 1 is mirror pan, channel 2 is mirror tilt, channel 3 is
color, channel 4 is gobo, channel 5 is shutter, channel 6 is
speed, and channel 7 controls the laser.
3. To run your fixture in DMX mode, plug in the fixture via the
XLR connections to any standard DMX controller. - Follow the
set-up specifications that come with your DMX controller.
Pocket Scan™
Operation Cont.
Adjusting The DMX address:
The DMX address is adjusteded by using the “1, 10, and 100” keys
directly below the LCD. Each press of a button will increase the
selected value of one. Please note that each tap of the keys will only
increase the displayed value, you may decrease the value.
Pocket Scan™
Reset Function
This function will reset all functions to their default setting. You may
reset the fixture by turing the unit on and off. If your units are being
controlled through a DMX controller, you may also reset the fixtures by
adjusting DMX channel seven to a value of 240-250.
This function will automatically shut off the lamp if the shutter is closed
for 10 - 15 minute in DMX mode.
Pocket Scan™
Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external
optical lenses must be carried out periodically to optimize light output.
1. Use normal glass cleaner and a soft cloth to wipe down the
outside casing.
2. Use a brush to wipe down the fan grill.
3. Clean the external optics with glass cleaner and a soft cloth
every 20 days.
4. Clean the internal optics with glass cleaner and a soft cloth
every 30-60 days.
5. Always be sure to dry all parts completely before plugging
the unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).
Pocket Scan™ LCD
100
©American
10
1
DJ Supply® - www.americandj.com - Pocket Scan™ Instruction Manual Page 13
©American
DJ Supply® - www.americandj.com - Pocket Scan™ Instruction Manual Page 14
Pocket Scan™
Fuse Replacement
Fuse Replacement: Caution! Always disconnect the main power
before attempting to replace the fuse. Remember always replace with
the same type lamp and fuse.
1. With a flat screwdriver wedge the fuse holder out of the its
housing
2. Remove the old fuse from the holder and replace with the
exact same type fuse.
3. Replace the fuse holder in to the fuse holder housing.
4. Reconnect main power.
Pocket Scan™
Lamp Replacement
Lamp Replacement: Caution! Never open the unit when in use. Always
disconnect the main power before attempting to replace the lamp.
Remember always replace with the same type lamp and fuse.
1. Be sure to follow the proper procedures when handling
halogen bulbs.
2. Lamp replacement has been made simple by incorporating
the use of a removable lamp cover and a thumb screw.
3. Loosen the thumb screw on front lower cover.
4. Remove the lamp cover.
5. Remove and replace the bulb.
6. Reassemble.
Pocket Scan™
DMX Settings
DMX CHANNEL
DMX512
LEVEL RANGE
0 - 255
1
2
PAN
TILT
WHITE
ORANGE 306
YELLOW 601
200
99
95
89
85
79
75
69
65
59
55
49
45
39
35
29
25
19
15
9
5
0
GREEN 204
UV108
MAGENTA 501
MAGENTA 507
CYAN 104
RED304
TORQUES 208
PINK 310
YELLOW 603
BLUE 101
ORANGE 302
GREEN 201
BLACKOUT
3
4
5
6
DJ Supply® - www.americandj.com - Pocket Scan™ Instruction Manual Page 15
7
8
GOBO 14
6
OPEN
7
LASER
AUDIO MODE
UNIT RESET
FAST
OPEN
FAST STROBE
FAST STROBE
GOBO 13
GOBO 12
GOBO 11
GOBO 10
GOBO9
GOBO 8
GOBO 7
GOBO 6
GOBO 5
GOBO 4
GOBO 3
SLOW
SLOW STROBE
RELATIVE
GOBO 2
CLOSED
GOBO 1
9
10
11
SLOW STROBE
CLOSED
12
13 14
Halogen Lamp Warning
This fixture is fitted with halogen lamps which are
highly susceptible to damage if improperly handled.
Never touch the lamps with your bare fingers as
the oil from your hands will shorten lamp life. Also,
never move the fixture until the lamps have had
ample time to cool. Remember, lamps are not covered under warranty conditions.
Focusing
1. To focus the Pocket ScanTM it is best to first turn down the
music so the mirror stops moving.
2. Loosen the thumb screw on the front of the unit that hold
the lens in place.
3. Adjust the focus by moving the lens up and down, until you
reach proper focus.
4. Tighten the thumb screws after you achieve your desired
focus.
©American
5
SHUTTER SPEED
Gobo layout. Note gobo one is Large Spot - Open Shutter.
Pocket Scan™ Pocket Scan™
4
GOBO
AUDIO MODE
AUDIO MODE
ROTATION CCW ROTATION CCW
ROTATION CW
ROTATION CW
255
2
3
COLOR
©American
DJ Supply® - www.americandj.com - Pocket Scan™ Instruction Manual Page 16
Pocket Scan™
Trouble Shooting
Listed below are a few common problems the user may encounter, with solutions.
No light from the unit;
1.
2.
3.
Check if the ‘Power On’ (red) LED is lit and the fan is
running. If not, there is no main supply.
Check the fuse in the back panel.
Check if lamp is lit. The user should be able to see some
light escape through the fan. If power is present but the
lamp is not lit, lamp may need to be replaced.
Note: The unit has been designed to shut the lamp down after
60 seconds of inactivity. This is a way of extending lamp life, be
assured this is not a problem with the fixture.
Unit not responding to DMX;
1.
2.
3.
4.
5.
If the RED LED in the LCD is flashing, the unit is definitely
receiving DMX Check for prper DMX addressing.
If the DMX LED is not lit, check that the DMX cables are
connected properly and are wired correctly (pin 3 is
‘hot’; on some other DMX devices pin 2 may be ‘hot’).
Also, check that all cables are connected to the right
connectors; it does matter which way the inputs and
outputs are connected.
If it is a bad connection, the RED LED may flash when
cables are wiggled (but remember it may also be the
unit sensing audio!)
If DMX connectors are fairly short, ordinary microphone
cables may be used. For longer runs, this may cause
©American
DJ Supply® - www.americandj.com - Pocket Scan™ Instruction Manual Page 17
Pocket Scan™
Trouble Shooting Cont.
data transmission problems (which will show up as
random or incorrect movements) for best result, use proper balanced data transmission cable.
Unit does not respond to sound;
1. Check to see if the unit is receiving DMX (the RED LED
should be off).
2. Quiet or high pitched sounds will not activate the unit.
Unit blacks out in stand alone mode;
1.
Some of the units’ built-in patterns include special
effects such as blackout sweeps. When connecting two
units up, only one is ever blackened out at once, and
the blackout ‘swaps’ between the units.
If problems are not resolved; Contact your American DJ® dealer
for service.
©American
DJ Supply® - www.americandj.com - Pocket Scan™ Instruction Manual Page 18
Pocket Scan™
Specifications
Model: Pocket Scan™
SPECIFICATIONS:
Working Position: Voltage: Lamp: Weight: Dimensions: Fuse: Colors:
Gobos:
Any safe working position
120V
ZB-JCR 12V/100W
10 lbs.
11.5” x 4.75” x 6”
2a GMA
15 plus white
13 plus spot
Pocket Scan™
Product Registration
The Pocket ScanTM comes with a 1 year limited warranty. We recommend filling out the warranty registration card that came with your
fixture to validate your warranty. You may also register your product
on-line at www.americandj.com.
©American
DJ Supply® - www.americandj.com - Pocket Scan™ Instruction Manual Page 19
American DJ®
American DJ World Headquarters:
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.americandj.com / E-mail: info@americandj.com
Download PDF