Samsung EV-1S Instruction manual

EV-1(GB)-RDS
12/17/02
16:17
Page 1
ULTRA SLIM
AUDIO SYSTEM
CD-R/RW PLAYBACK
EV-1/EV-1S
Instruction Manual
EV-1(GB)-RDS
12/17/02
16:17
Page 2
Safety Warnings
GB
CLASS 1 LASER PRODUCT
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LASER CLASE 1
This Compact Disc player is classified as a CLASS 1
LASER product.
Use of controls adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
CAUTION-INVISIBLE LASER RADIATION WHEN OPEN
AND INTER LOCKS DEFEATED, AVOID EXPOSURE TO
BEAM.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE REAR COVER, NO USER
SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
This symbol indicates that dangerous voltage constituting of a risk of electric shock is present within
this unit.
This symbol indicates that there are important operating and maintenance instructions in the owners
manual accompanying this unit.
Wiring the Mains Power Supply Plug(UK Only)
IMPORTANT NOTICE
The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin face
of the plug and, if it requires replacing, a fuse approved to BS1362 of the same rating must be used.
Never use the plug with the fuse cover omitted. If the cover is detachable. If a replacement fuse cover is required, it must be of the same
colour as the pin face of the plug. Replacement covers are available from your dealer.
If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you should obtain
a suitable safety approved extension lead or consult your dealer for assistance.
However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do NOT connect the plug to
a mains socket as there is a risk of shock hazard from the bared flexible cord.
IMPORTANT
The wires in the mains lead are coloured in accordance with the following code:–
BLUE = NEUTRAL
BROWN = LIVE
As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as follows:–
The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured
BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.
WARNING:
1
DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH THE LETTER E OR BY
THE EARTH SYMBOL
, OR COLOURED GREEN OR GREEN AND YELLOW.
EV-1(GB)-RDS
12/17/02
16:17
Page 3
Precautions
GB
Standby
Function
+
VOL.
Function
+
Mode
—
VOL.
—
Mode
Standby
Ensure that the AC power supply in your house complies with the identification sticker located on the back of your player. Install your player horizontally, on a suitable base (furniture), with enough space around it for ventilation (3~4inches). Make sure the ventilation slots are
not covered. Do not stack anything on top of the player. Do not place the player on amplifiers or other equipment which may become hot.
Before moving the player, ensure the disc tray is empty. This player is designed for continuous use. Switching off the CD player to the
stand-by mode does not disconnect the electrical supply. In order to disconnect the player completely from the power supply, remove the
main plug from the wall outlet, especially when left unused for a long period of time.
Standby
Function
+
VOL.
Mode
Standby
—
Function
+
VOL.
Mode
—
During thunderstorms, disconnect the main plug from the socket.
Main voltage peaks due to lightning could damage the unit.
Standby
Do not expose the unit to direct sun radiation or other heat
sources.
This could lead to overheating and malfunction of the unit.
Function
+
VOL.
Mode
—
Phones
Protect the player from moisture(dripping or splashing and that no objects
filled with liquids,such as vases, shall be placed on the player), and excess
heat(e.g.fireplace) or equipment creating strong magnetic or electric fields
(i.e.speakers...) disconnect the power cable from the mains electricity supply
if the player malfunction. Your player is not intended for industrial use but
for domestic purposes only. Use of this product is for personal use only.
Condensation If your player or disc have been stored in a cold atmosphere.
as for example during transportation in the winter, wait for approximately 2
hours until they have reached room temperature.
The battery used in this product contains the chemicals that
are harmful to the environment.
Do not dispose of batteries in the general household waster.
It is recommended that the replacement of the battery should
be done by technician.
2
EV-1(GB)-RDS
12/17/02
16:17
Page 4
Thank you for buying this
SAMSUNG ULTRA SLIM audio system.
Contents
Please take time to read these instructions.
They will allow you to operate your
system with ease and take full advantage
of its features.
GB
SAFETY WARNINGS .................................................................................................................................................................................. 1
Precautions ............................................................................................................................................................................................2
INSTALLING YOUR ULTRA SLIM AUDIO SYSTEM
Front Panel View ........................................................................................................................................................................................4
Rear Panel View ........................................................................................................................................................................................4
Remote Control ..........................................................................................................................................................................................5
Speaker Connection ..................................................................................................................................................................................6
Connecting your System to the Power Supply ..........................................................................................................................................6
Connecting the FM and AM(MW/LW) Antennas ........................................................................................................................................7
Connecting to an External Source ............................................................................................................................................................8
Viewing the Various Functions on Your System ........................................................................................................................................8
Adjusting the brightness of the LCD display ..............................................................................................................................................8
Using the function button ..........................................................................................................................................................................9
Using the Mode button ........................................................................................................................................................9
Setting the Clock ......................................................................................................................................................................................10
Listening to a Compact Disc ....................................................................................................................................................................10
Regarding the playback of CD-R/RW ......................................................................................................................................................10
Selecting a Track......................................................................................................................................................................................11
Searching for a Specific Music Passage on a CD ..................................................................................................................................11
Function to skip through 10 tracks at a time ............................................................................................................................................11
CD-PLAYER
Random play function ..............................................................................................................................................................................12
Repeating One or All Tracks on the Compact Discs ..............................................................................................................................12
Programming the Order of Playback........................................................................................................................................................13
Checking or Changing Programmed Tracks............................................................................................................................................13
Searching for and Storing the Radio Stations..........................................................................................................................................14
Selecting a Stored Station........................................................................................................................................................................14
Improving Radio Reception ......................................................................................................................................................................14
TUNER
About RDS broadcasting..........................................................................................................................................................................15
About RDS DISPLAY function..................................................................................................................................................................15
PTY(Program Type) indication and PTY-SEARCH function ....................................................................................................................16
Timer Function ........................................................................................................................................................................................17
Cancelling the Timer ................................................................................................................................................................................17
Mute Function ..........................................................................................................................................................................................18
Selecting an Equalizer Preset ..................................................................................................................................................................18
S. Bass Function ......................................................................................................................................................................................18
Power Sound............................................................................................................................................................................................18
OTHER FUNCTIONS
Setting the System to Switch off Automatically........................................................................................................................................19
Connecting Headphones..........................................................................................................................................................................19
RECOMMENDATIONS FOR USE
Cleaning Your ULTRA SLIM Audio System ............................................................................................................................................19
Precautions When Using Compact Discs ................................................................................................................................................19
Before Contacting the After-Sales Service ..............................................................................................................................................20
Technical Specifications ..........................................................................................................................................................................21
Symbols
Press
3
Push
Important
Note
EV-1(GB)-RDS
12/17/02
16:17
Page 5
Front Panel View
GB
Standby
Function
+
VOL.
Mode
1
2
3
4
1. On/Standby
5. Mode
2. Disc Tray
6. Function(CD, TUNER, AUX)
3. Open/Close
7. Volume
—
5 6 7
4. Multi-function Button
*Depending on the selected Mode, pressing the
corresponding button will activate that button.
Rear Panel View
PHONES
DIGITAL OUT
(OPTICAL)
AM
ANTENNA
AUX IN
COAXIAL
L
FM
75
R
1
2
L
SPEAKERS
(6 )
3
R
4
5
6
1. AM Aerial Connector Terminal
2. FM Aerial Connector Terminal
3. Speaker Connector Terminal
4. Aux-Input
5. Headphone Jack connector
6. Digital Out Jack
4
EV-1(GB)-RDS
12/17/02
16:17
Page 6
Remote Control
GB
Timer/
Clock
Timer
On/Off
On/Standby
Timer/Clock
Timer On/Off
P.Sound
Sleep
AUX
P.Sound
S.Bass
S.Bass
EQ
EQ
Demo
AUX
Sleep
Dimmer
Dimmer
Open/Close
Display
+10
RDS
Demo
PTY(RDS)
Display(RDS)
PTY
Open/Close
CD
+10
CD Skip or Search
CD Play
CD Stop
Program/Set
Tuning Up/Down
Band
Program/
Set
VOL.
Band
Volume Control
Mode
Tuning Mode
VOL.
Mono/ST
Mute
Mono/ST
Insert Remote Batteries
1
2
Remove the battery cover
on the back of the remote
by pressing down and
sliding the cover in the
direction of the arrow.
Insert two 1.5V AAA batteries,
paying attention to the correct
polarities (+ and –).
Mute
Range of Operation of the Remote Control
The remote control can be used up to approximately 23 feet/7 meters in a straight line. It can
also be operated at a horizontal angle of up to
30° from the remote control sensor.
Standby
Function
+
VOL.
Mode
30
30
7~10m
Timer/
Clock
Timer
On/Off
P.Sound
Sleep
S.Bass
EQ
Open/close
+10
Demo
Display
AUX
Dimmer
RDS
PTY
CD
3
Replace the battery cover.
Follow these precautions to avoid leaking or cracking cells:
• Place batteries in the remote control so they match
CAUTION the polarity:(+) to (+)and (–)to (–).
• Use the correct type of batteries.Batteries that look
similar may differ in voltage.
• Always replace both batteries at the same time.
• Do not expose batteries to heat or flame.
5
Program/
Set
VOL.
Band
Mode
VOL.
Mono/ST
Mute
—
EV-1(GB)-RDS
12/17/02
16:17
Page 7
Speaker Connection
GB
• Speaker Connection: Connect the Speaker cords(red/black) to the Speaker jack of the system.
PHONES
DIGITAL OUT
(OPTICAL)
AM
ANTENNA
AUX IN
COAXIAL
L
L
FM
75
SPEAKERS
(6 )
R
R
— +
L
SPEAKERS
(6 )
R
—+
(Left Speaker)
(Right Speaker)
Directions in Installing Speaker
• Installation in a place near heating apparatus, under directly of light or with high humidity may
cause performance deration of the speaker.
• Do not install on the wall or on a high place of pole or other unstable place to
prevent any safety accident caused by falling of the speaker.
• Do not take the speaker apart from TV or computer monitor.
The speaker near the TV or computer monitor may influence the quality of the screen display.
Connecting your System to the Power Supply
The main lead must be plugged into an appropriate socket.
Before plugging your system into a main socket, you must check the voltage.
1. Plug the main lead (marked AC Cord on the rear of the system) into an appropriate socket.
2. Press the On/Standby button to switch your ULTRA SLIM audio system on.
PHONES
DIGITAL OUT
(OPTICAL)
AM
ANTENNA
AUX IN
COAXIAL
L
FM
75
L
SPEAKERS
(6 )
R
R
6
EV-1(GB)-RDS
12/17/02
16:17
Page 8
Connecting the FM and AM(MW/LW) Antennas
GB
If FM reception is poor,
connect an outdoor FM
antenna (not supplied).
AM Loop Antenna
(supplied)
ANTENNA
Snap the tabs on the loop into the slots of
the base to assemble the AM loop antenna.
FM Antenna (supplied)
PHONES
DIGITAL OUT
OPT.
AM
ANTENNA
AUX IN
COAXIAL
L
L
FM
75
SPEAKERS
(6 )
R
R
Cooling fan (See “About cooling Fan” below.)
FM antenna connection
1. Connect the FM antenna supplied to the FM
75Ω COAXIAL terminal.
2. Slowly move the antenna wire around until you
find a location where reception is good, then
fasten it to a wall or other rigid surface.
• If reception is poor, connect an outdoor antenna.
Before attaching a 75Ω coaxial cable (with a standard
type connector), disconnect the supplied FM antenna.
(About the cooling fan)
A cooling fan is mounted on the rear panel of the center unit to
prevent abnormal temperature inside the center unit, thus assuring
normal operation. The cooling fan automatically starts rotating to
supply external cool air to the inside of the center unit when the
internal temperature exceeds the specified limit.
7
AM(MW/LW) antenna connection
1. Connect the AM loop antenna supplied
to the AM and
terminals.
2. If reception is poor, connect an outdoor
single vinyl-covered wire to the AM
terminal. (Keep the AM loop antenna
connected).
For safety, observe the following carefully.
• Make sure there is good ventilation around the center unit.
Poor ventilation could overheat and cause damage.
• DO NOT block the cooling fan and the ventilation openings or
holes. (If they are blocked by a newspaper or cloth, etc., the heat
may not be able to escape.)
EV-1(GB)-RDS
12/17/02
16:17
Page 9
Viewing the Various Functions
on Your System
Connecting to an External Source
GB
The auxiliary input can be used to take advantage of the
sound quality of your ULTRA SLIM audio system when
listening to other sources.
Examples: A television
A video disc player
A Hi-Fi stereo video cassette recorder
You can view the various functions available on your system.
1
All these functions are described in detail in this booklet.
For instructions on how to use them, refer to the appropriate
sections.
To connect the external source, the source must have an audio
output. In addition, you need an RCA connection cable.
1
Set the system to standby mode and disconnect it and the external
source from the main.
2
Connect the audio cable to the rear of the ULTRA SLIM audio system.
Connect the...
To the connector marked...
Red jack
White jack
R (right)
L (left)
For optimum sound quality, do not invert the right and left
channels.
3
4
5
6
Plug the system back into the main socket and press On/Standby
(
) to switch it on.
Press the Demo button.
Result: The various functions available are listed in turn on the
display.
2
To cancel this function, press Demo again.
Timer/
Clock
Timer
On/Off
Sleep
P.Sound
S.Bass
Open/Close
EQ
Demo
Dimmer
Display
+10
Select the AUX source by pressing the AUX button.
Result: AUX is displayed.
AUX
RDS
PTY
CD
Switch the external source on.
Adjust the volume and balance as required:
Volume
Equalizer
S.Bass
Example: You can watch a film and take advantage of stereo sound
provided that the original sound track is in stereo (as if you
were in a cinema).
Adjusting the brightness of the
LCD display
You can adjust the brightness of the LCD display depending
on the surrounding lighting conditions
Press the Dimmer button on the remote control to adjust the brightness.
AUX IN
L
The selection switches each time the button is pressed:
Dimmer1(Bright) ➞ Dimmer2 (Medium) ➞ Dimmer3(Dim).
L
SPEAKERS
(6 )
R
R
Timer/
Clock
Timer
On/Off
P.Sound
S.Bass
Timer
On/Off
Timer/
Clock
Open/Close
Sleep
EQ
Demo
Display
+10
AUX
Dimmer
RDS
PTY
CD
P.Sound
Sleep
AUX
Program/
S.Bass
EQ
Demo
VOL.
Band
Dimmer
8
EV-1(GB)-RDS
12/17/02
16:17
Page 10
Using the Function button
Using the Mode button
GB
Function
Function
+
+
VOL.
Mode
VOL.
—
• Press the Function button
Each time the button is pressed, one of the following
function are selected.
Select CD
—
Mode
• Press the Mode button on the front panel of the main unit.
Each time the button is pressed, the selection changes as follows.
You can pressed the button below the display to select the
desired function.
During CD operation
(For example, 15 tracks with
playback time of 53:05)
Normal
Mode
Play
Mode 1
Repeat
Random
Repeat
Random
Back
Next
Stop
Mode
Select AUX
Mode
Rpt-1
Rand-On
Rpt-All
Mode 2
Select TUNER
Pass
PSnd
SBass
Mode
Pass
(For example, FM 89.1 MHz)
Classic
PSnd
SBass
Rock
Pop
PSnd-On
SBass-1
SBass-2
During TUNER operation
Normal
Mode
FM
Down
Up
Manual
Mode
About the Mode button
FM
MW
LW
If no button is pressed within 8 seconds
while in the Mode 1 or Mode 2, the Display switches to the Normal Mode.
Mode 1
Pass
PSnd
SBass
Mode
Pass
Classic
Rock
Pop
PSnd
SBass
PSnd-On
SBass-1
SBass-2
Mode does not work in AUX Function.
9
EV-1(GB)-RDS
12/17/02
16:17
Page 11
Setting the Clock
Listening to a Compact Disc
Your system is equipped with a clock which allows you to
turn your system on and off automatically.
You should set the clock:
When you first purchase the ULTRA SLIM audio system
After a power failure
After unplugging the unit
For each step, you have a few seconds to set the required
options. If you exceed this time, you must start again.
1
2
Switch the system on by pressing On/Standby (
).
Press Timer/Clock twice.
Result: Clock is displayed.
3
Press Program/Set.
Result: The hour flashes.
4
To...
Press...
Increase the hours
Do not use CDs of irregular shapes like heart or octagon shapes.
The performance of the player be degraded.
The CD disc 12 cm or 8 cm compact discs without using
an adapter.
1
2
3
4
5
6
Decrease the hours
5
When the correct hour is displayed, press Program/Set.
Result: The minutes flash.
6
To...
7
Press the Open/Close ( ) button.
Result: The CD tray is opened.
Place the CD on the tray so that the CD Label faces upward.
Press the Open/Close ( ) button to close the tray.
Result: Number of tracks and the total playback time are shown on
the display.
Press the CD(
) button for playback.
Adjust the volume according to needs with the following procedures.
Press the VOL.+ or button on the remote control
Press the VOL.+ or button on the front panel.
If it desired to stop while the playback is processing, press the CD
(
) button.
Press the CD (
Press...
8
Increase the minutes
Press the CD button on the main body and select CD.
) button once again to playback again.
To stop playback, press the (
) button.
Decrease the minutes
7
When the correct time is displayed, press Program/Set.
Result: The clock starts and is displayed, even when the system is in
standby mode.
Open/Close
Display
+10
RDS
PTY
CD
2,4
You can display the time, even when you are using another
function, by pressing Timer/Clock once.
5,7
8
Timer/
Clock
Timer
On/Off
VOL.
Program/
Set
Band
6
1
P.Sound
S.Bass
Open/Close
Sleep
EQ
Demo
Display
+10
2AUX
Mode
Dimmer
RDS
PTY
VOL.
6
CD
Regarding the playback of CD-R/RW
3,5,7
Program/
Set
VOL.
Band
Mode
VOL.
4,6
Mono/ST
4,6
Mute
In the case of an original CD-R(Recordable) recorded in audio CD
format, CD-RW(Rewritable)and editing by the user, playback is
processed on the respective completed status. (The player may not
be played back according to the characteristics of the CD or recorded
status.)
The CD-RW is comparably less reflexive than CD which cause more
time delay to read.
10
EV-1(GB)-RDS
12/17/02
16:17
Page 12
Function to skip through 10
tracks at a time
Selecting a Track
GB
You can select the track you wish to listen to, either when the
compact disc player is stopped or when a disc is playing.
Press the +10 button briefly while playing back a
CD. The track 10 tracks after the current one will then
be played back.
To start playback at the beginning of the...
Example: If you want to select track 43 during playback of track
15, press the +10 button three times, and then press
the
button three times.
Press...
Next track
once
Current track
once
Previous track
twice
Track of your choice
or
the
appropriate number
of times.
15 ➝ 20 ➝ 30 ➝ 40 ➝ 41 ➝ 42 ➝ 43
+10
+10
+10
CD
P.Sound
Program/
Set
VOL.
Band
Mode
S.Bass
EQ
Demo
Open/Close
+10
Display
AUX
Dimmer
RDS
PTY
CD
VOL.
Mono/ST
Sleep
Mute
Searching for a Specific Music
Passage on a CD
Program/
Set
VOL.
Band
Mode
VOL.
When listening to a compact disc, you can quickly search for a
specific music passage on a track.
To search through the tracks...
Press and hold down...
Forwards
Backwards
for at least one second
for at least one second
It is recommended that you turn the volume down before using
this function.
CD
Program/
Set
VOL.
Band
Mode
VOL.
Mono/ST
11
Mute
Mono/ST
Mute
EV-1(GB)-RDS
12/17/02
16:17
Page 13
Repeating One or All Tracks
on the Compact Discs
Random play function
GB
You can listen to the tracks on a compact disc in a
different order each time, as the various tracks will be
selected automatically in a random sequence.
You can repeat indefinitely:
A specific track on a compact disc.
All tracks on the compact disc selected.
1
1
Press the Mode button on the front Panel until “Repeat” is displayed on
the bottom.
2
To repeat...
Press the Repeat button one or
more times until...
The current track indefinitely
All songs
Repeat 1 is displayed
Repeat All is displayed
2
3
Press the Mode button on the Front Panel until
“Random”is displayed to bottom.
If this button is pressed when the CD is being played
back or stopped, any track recorded in the CD may be
selected to playback again.
Press Random button, “Rand-On”is displayed.
When you finished the random playback, press the Random button again.
3
When you wish to stop the Repeat function, press the Repeat button
until “Repeat off” is displayed.
Function
Function
+
+
VOL.
Repeat
Random
Mode
—
VOL.
Repeat
Random
Mode
2, 3
1
2, 3
—
1
If no button is pressed within 8 seconds, the Display
changes to the Normal Mode.
To proceed with the third operation, you should
repeat from the first operation.
12
EV-1(GB)-RDS
12/17/02
16:17
Page 14
Checking or Changing Programmed Tracks
Programming the Order of Playback
GB
You can decide:
You can check or change your selection of tracks at any time.
The order of the track desired to listen
The track not desired to listen
A maximum of up to 24 order of tracks desired to listen
may be programmed.
Before selecting the track, the CD player should be stopped.
This function may be used simultaneously with the CD
Repeat function.
1
2
3
once if you have started listening to the selection.
Press Program/Set twice.
Result: The following indications are displayed:
Program no.
If the CD function is selected, stop the player by pressing
Track no. on the disc
Select the required track by pressing:
to move back through the tracks
to move forward through the tracks
5
Press Program/Set to confirm your selection.
Result: The selection is stored and is displayed.
3
Press Program/Set one or more times until the track to be changed
is displayed.
4
5
6
Press
or
to select a different track.
Press Program/Set to confirm your change.
Press CD ( ) to start listening to the selection.
Result: The first track selected is played.
Open/Close
Display
+10
RDS
PTY
To select other tracks, repeat Steps 5 to 6.
Press CD (
) to listen to the track selection in the order programmed.
1
Press...
Listen to the current track again
Listen to the previous track
Listen to the next track
Skip forwards or backwards
one or more tracks
once
twice
once
or
the appropriate
number of times
To cancel the selection, press
button.
Once if the compact disc player is stopped
Result: Program function is no longer displayed.
Open/Close
4, 8
Display
+10
2, 9
3, 5
Program/
Set
RDS
4
4,8
7
VOL.
Band
Mode
VOL.
Mono/ST
Mute
6
2,3,5
Program/
Set
VOL.
Band
Mode
VOL.
Mono/ST
PTY
CD
CD
4
To...
If you open the compartment, the selection is cancelled.
13
Track no. on the disc
If you have already programmed 24 tracks, Ch is displayed
instead of Pr when you press Program/Set.
button .
Press Program/Set.
Result: The following indications are displayed:
4
9
Press
Load the selected CDs.
Program no.
6
7
8
1
2
Mute
EV-1(GB)-RDS
12/17/02
16:17
Page 15
Searching for and Storing the
Radio Stations
Selecting a Stored Station
GB
You can listen to a stored radio station as follows:
You can store up to:
15 FM stations
15 MW stations
7 LW stations
1
2
3
1
2
Switch the system on by pressing On/Standby (
).
Select the required frequency band by pressing Band on the
remote control.
Result: The appropriate indication is displayed:
FM
Frequency Modulation
AM(MW)
Medium Wave
LW
Long Wave
To search for a
station...
3
Switch the system on by pressing On/Standby (
).
Select the required frequency band by pressing Band on the
remote control.
Select the radio station as follows.
To listen to ...
Press ...
Stored station
1. Press the Mode button on the remote
control until “Preset” is displayed.
2. Press
or
button to select the
required program.
Press Mode on the remote
Control
One or more times until Manual is
displayed.
Automatically
One or more times until Auto is
displayed.
PRESET function is explained in detail in the section
“ Selecting a Stored Station” on.
Manually
4
Select the station to be stored by:
Pressing
or
buttons to increase or decrease the
frequency respectively.
To scroll through the frequencies faster when
searching manually, hold down the
or
buttons.
The automatic search procedure may stop on a
frequency that does not correspond to a radio station.
If this happens, use the manual search mode.
5
2
Program/
Set
Band
VOL.
3
Mode
Mode
3
3
VOL.
Mono/ST
Mute
If you do not want to store the radio station found, revert to Step 4
and search for another station.
Otherwise:
a Press Program/Set.
Result: ’Program No.’ is displayed for a few seconds.
b Press Program/Set to store the radio station.
Result: ’Program No.’ is no longer displayed and the station is
stored.
6
To store any other radio frequencies required, repeat Steps 3 to 5.
The PROGRAM function can be used to assign a new station
to an existing program number.
2
5
Program/
Set
4
Band
VOL.
3
Improving Radio Reception
You can improve the quality of radio reception by:
Rotating the FM or AM(MW) aerial
If reception from a specific FM radio station is poor, press Mono/ST.
to switch from stereo mode to mono. The quality of the sound will be
improved.
Program/
Set
Band
4
Mode
Mode
Mode
VOL.
VOL.
Mono/ST
VOL.
Mute
Mono/ST
Mute
14
EV-1(GB)-RDS
12/17/02
16:17
Page 16
About RDS broadcasting
GB
About RDS DISPLAY function
About "PS NAME" MODE
This unit has the RDS (Radio Data System) function, which enables for
the various information such as broadcasting station, radio text, time
and 30 types of programs (News, Rock, Classic, etc.) to be received
from the FM RDS station together with normal radio signal.
1
2
3
Press the On/Standby (
) button.
Receive the FM radio.
See the radio receiving method on the page 14.
FM and frequency are shown on the display
If the received station transfers the RDS information, 'RDS'
appears automatically on the display.
Displays the name of broadcasting station.
Press the RDS Display button to select the PS NAME.
"PS NAME" appears on the display.
If the PS information is being received, the PS name (BBC, AFO, NDR,
etc.) is shown on the display.
If the PS information isn't received, the original FM frequency is shown.
Even though no RDS Display button is pressed, the reception
of PS information ensues the PS name is displayed.
Press the RDS Display button to select the desired RDS mode.
Whenever the button is pressed, RDS mode changes as follows.
PS NAME
RT
CT
Current FM frequency
The RDS function is available only in FM broadcasting.
S.Bass
EQ
Demo
Open/Close
+10
Display
Description on RDS function
Dimmer
RDS
PTY
CD
1. PTY(Program Type) : Displays the type of programme
currently being broadcast
2. PS NAME(Program Service Name) : Indicates the name of
broadcasting station and is composed of 8 characters.
3. RT(Radio Text) : Decodes the text broadcast by a station (if
any) and is composed of maximum 64 characters.
4. CT(Clock Time) : Decodes the real time clock from the FM
frequency.
Some stations may not transmit PTY, RT or CT
information therefore this may not be displayed in all
cases.
5. TA(Traffic Announcement) : When this symbol flashes it
shows that the traffic announcement is in progress.
Sleep
P.Sound
Displays the character transmitted from the broadcasting station.
Press the RDS Display button to select the RT MODE.
"RT" appears on the display.
If the RT information is being received, the received information is
shown on the display.
If the RT information isn't received, the "NO RT" is shown.
On the display.
S.Bass
EQ
Demo
Open/Close
+10
Display
Timer/
Clock
Timer
On/Off
1
About 'RT' MODE
AUX
Dimmer
RDS
PTY
CD
About CT(Clock Time)
Sets the time of RDS clock.
S.Bass
EQ
Demo
Open/Close
+10
Display
3
CD
Dimmer
To select the CT time, set the RDS Display button to CT MODE.
RDS
PTY
The CT information will take up to 2 minutes to be decoded
therefore the clock isn’t displayed immediately.
If there is no received CT information, "NO CT" is
displayed.
S.Bass
EQ
Demo
Open/Close
+10
Display
CD
15
Dimmer
RDS
PTY
EV-1(GB)-RDS
12/17/02
16:17
Page 17
PTY(Program Type) indication
and PTY-SEARCH function
GB
◆ The PTY information is composed of an identification symbol, which helps
the FM radio to recognize the program type of each FM station.
About PTY-SEARCH
◆ The below 30 PTY information is shown on the display by pressing the Pty
button.
1
The FM and frequency appear on the display.
If the
e received
station is transmitting the RDS information,
r
“RDS” lights up.
Program Type
Display
News
• News including an announced opinion and report
Affairs
• Several matters including a current incident, documentary,
discussion and analysis.
Info
• Information including weights and measures, returns and forecast, matters interesting the customer, medical information, etc.
Sport
• Sports
Educate
• Education
Drama
• Drama-Radio serial, etc.
Culture
• Culture-National or local culture including the religious problem,
social science, language, theater,etc.
Science
• Natural science and technology
Varied
• Others-Speech, amusing program (quiz, game), interview,
comedy and satirical play, etc.
Pop M
• Pop music
Rock M
• Rock music
M.O.R.M
• M.O.R- Comfortable music, occasionally vocal or piece
Light M
• Light classical music- Classical music and instrumental
and chorus music
Classics
• Heavy classical music-Orchestra music, symphony, chamber
music and opera
Other M
• Other music - Jazz, R&B country music
Weather
• Weather
Finance
• Finance
Children
• Children’s programmes
Social
• Social affairs
Religion
• Religion
Phone In
• Phone in
Travel
• Travel
Leisure
• Leisure
Jazz
• Jazz Music
Country
• Country Music
National M
• National Music
Oldies
• Oldies Music
Folk M
• Folk Music
Document
• Documentary
Test
• Alarm Test
Receive the FM radio.
See the radio receiving method on the page 14.
2
Press the PTY button.
The PTY MODE(NEWS, AFFAIRS, etc.) appears on the display.
Press the TUNING
or
button to select the desired PTY
MODE.
If the station is transmitting no PTY information, 'NO PTY' lights
on the display.
When the PTY MODE is selected(The PTY MODE is shown on
the display), press the PTY KEY once again to convert into
PTY-SEARCH MODE and auto-search the station sequentially.
If the PTY MODE received in the course of auto-search agrees
with the selected PTY MODE, the auto-search stops and the
PTY-SEARCH is finished.
If the PTY MODE which agrees with the PTY MODE selected in
the course of auto-search, isn't received, it is returned to the first
frequency at beginning the PTY SEARCH and the auto-search
and PTY SEARCH are suspended.
S.Bass
EQ
Demo
Open/Close
+10
Display
Dimmer
RDS
PTY
2
CD
Program/
Set
VOL.
Band
2
2
Mode
VOL.
Mono/ST
Mute
16
EV-1(GB)-RDS
12/17/02
16:17
Page 18
Timer Function
GB
The timer enables you to switch the system on or off at
specific times.
Example: You wish to wake up to music every morning.
1,9
Before setting the timer, check that the current time is correct.
For each step, you have a few seconds to set the required
options. If you exceed this time, you must start again.
1
2
3
4
5
Switch the system on by pressing On/Standby (
Press Timer/Clock until
TIMER is displayed.
7
Press
or
button to select the source to be played when the
system switches on.
If you select...
TUNER (radio)
CD (compact disc)
You must also...
a Press Program/Set.
b Select a preset station by pressing
or
.
Tuning
EQ
Demo
Open/Close
+10
Display
Dimmer
RDS
PTY
3,4,5,6,7,8
Program/
Set
4,5,6,7
Band
VOL.
4,5,6,7
Mode
VOL.
Cancelling the Timer
After having set the timer, it will start automatically as shown
by the TIMER indication on the display. If you no longer wish
to use the timer, you must cancel it.
You can stop the timer at any time (system on or in standby mode).
To...
Press Timer On/Off...
Cancel the timer
Once.
Result:
is no longer displayed.
Restart the timer
Twice.
Result:
is displayed again.
Load a compact disc.
Press Program/Set to confirm the timer.
Press On/Standby (
) to set the system to standby mode.
Result:
is displayed to the bottom right of the time, indicating that
the timer has been set. The system will switch on and off
automatically at the required times.
If the timer switch on and off times are identical, the word Error is
displayed.
17
AUX
CD
Set the timer switch-on time.
a Set the hour by pressing
or
button.
b Press Program/Set.
Result: The minutes flash.
c Set the minutes by pressing
or
button.
d Press Program/Set.
Result: OFF TIME is displayed for a few seconds, followed by
any switch-off time already set; you can now set the timer
switch-off time.
Press
or
button to adjust the volume level and press Program/Set.
Result: The source to be selected is displayed.
Sleep
S.Bass
Press Program/Set.
Result: ON TIME is displayed for a few seconds, followed by any
switch-on time already set; you can set the timer switch-on
time.
6
8
9
P.Sound
).
Set the timer switch-off time.
a Set the hour by pressing
or
button.
b Press Program/Set.
Result: The minutes flash.
c Set the minutes by pressing
or
button.
d Press Program/Set.
Result: VOL 20 is displayed, where 20 corresponds to the
volume already set.
Timer/
Clock2
Timer
On/Off
If you no longer want the system to be switched on or off
automatically, you must cancel the timer.
Timer
On/Off
P.Sound
Sleep
Timer/
Clock
AUX
EV-1(GB)-RDS
12/17/02
16:17
Page 19
S. Bass Function
Mute Function
GB
You can turn the sound off temporarily on your system.
Example: You wish to answer a telephone call.
S.Bass(Super Bass) function emphasizes the bass sound to
produce the effect of explosion or booms.
Turn the S.Bass Level button.
1
2
Press Mute.
Press S.Bass on the remote control repeatedly to select
S-Bass Off ➔ S-Bass 1 ➔ S-Bass 2.
To switch the sound back on (at the same volume as before), press
Mute again or the Volume buttons.
Band
VOL.
Program/
Set
Select the desired level for the bass.
S.Bass
EQ
Demo
Dimmer
Open/Close
+10
Display
RDS
PTY
CD
Mode
VOL.
Mono/ST
Power Sound
Selecting an Equalizer Preset
Your micro component system is equipped with a preset
equalizer that allows you to choose the most appropriate
balance between treble and bass frequencies, according to the
type of music you are listening to.
Press EQ on the remote control until the required option is selected.
Sleep
P.Sound
S.Bass
EQ
Demo
Open/Close
+10
Display
CD
This machine is equipped with the function of Power Sound
which amplifies bass treble output to twice as much for
powerful real sound.
1
2
Press the button repeatedly to select
Pass ➞ Classic ➞ Rock ➞ Pop.
Press the P. Sound button.
Press the button repeatedly to select P-Sound On ➞ P-Sound Off.
To cancel this function, press P. Sound button again.
AUX
P.Sound
Dimmer
S.Bass
EQ
Demo
Open/Close
+10
Display
Sleep
RDS
PTY
Band
VOL.
Program/
Set
Mute
AUX
Dimmer
RDS
PTY
CD
18
EV-1(GB)-RDS
12/17/02
16:17
Page 20
Setting the System to Switch
off Automatically
Cleaning Your ULTRA SLIM
Audio System
GB
While listening to a compact disc or a cassette, you can
set the system to switch off automatically
Example: You wish to go to sleep to music.
1
Press Sleep.
Result: The following indications are displayed:
2
Sleep 90
Press Sleep one or more times to indicate how long the
system should continue playing before it switches off:
Sleep 90
Sleep Off
Sleep 60
Sleep 45
Sleep 10
Sleep 20
Sleep 30
At any time, you can:
Check the remaining time by pressing Sleep
Change the remaining time by repeating Steps 1 and 2
3
To cancel SLEEP function, press Sleep one or more times until
Sleep Off is displayed.
Timer
On/Off
P.Sound
S.Bass
Sleep
EQ
Demo
Timer/
Clock
AUX
To obtain the best possible results from your ULTRA SLIM audio
system, you must clean the following elements regularly:
The outer casing
The compact disc player
Always unplug the system from the wall outlet:
Before cleaning it
If you are not going to be using it for a long time
Outer Casing
Clean the outer casing regularly using a soft cloth and a light detergent. Do
not use abrasive powders, liquids or aerosol cleaners. Never let any liquids
get into the system.
Compact Disc Player
1
Before playing a compact disc, clean it with a special CD cleaning
agent. Do not use the same cleaning agents as for vinyl LP records.
Carefully wipe the disc from the centre outward.
2
Regularly clean the player with a special cleaning disc (available from
your local dealer).
If you will not be using the remote control for a long time,
remove the batteries to prevent corrosion.
Although your system is very hard-wearing, it should not be
used in an excessively dusty environment or subjected to
shocks or extreme heat (close to heating appliances or in
direct sunlight, etc.).
If the unit emits an unpleasant odor when in use, unplug it
from the main supply and contact the after-sales service.
Dimmer
Connecting Headphones
You can connect a set of headphones to your ULTRA SLIM
audio system so that you can listen to music or radio programmers without disturbing other people in the room. The
earphones must have a 3.5ø jack or an appropriate adapter.
Connect the headphones to the Phones jack on the rear panel.
Result: The loudspeakers are no longer used to output the sound.
Prolonged use of headphones at a high volume may damage
your hearing.
Precautions When Using Compact Discs
Handle your compact discs with care. Always hold them by the
edges to avoid leaving fingerprints on the shiny surface.
When you have finished playing a compact disc, always put it back
in its case.
Do not fix paper or adhesive tape to the discs and do not write on
the label.
Clean them with a special-purpose cloth.
Store your compact discs in a clean place, out of direct sunlight,
where they will not be exposed to high temperatures.
Always use compact discs marked
.
COMPACT
DIGITAL AUDIO
PHONES
AUX IN
L
AKERS
(6 )
R
19
EV-1(GB)-RDS
12/17/02
16:17
Page 21
Before Contacting the After Sales Service
GB
It always takes a little time to become familiar with a new appliance.
If you have any of the problems listed below, try the solutions given. They may save you the time and inconvenience of an unnecessary service
call.
Problem
G
E
N
E
R
A
L
C
D
R
A
D
I
O
Checks/Explanation
The system does not work
• The main lead is not correctly plugged into a wall socket or the wall
socket is not switched on.
• The remote control batteries need replacing or the polarity has not
been respected.
• The On/Standby button has not been pressed.
There is no sound
• The volume has been completely turned down.
• The correct function (TUNER, CD, AUX) has not been selected.
• You have connected a set of earphones.
• The loudspeaker wires have been
disconnected.
• The Mute button on the front panel for has been pressed.
The Timer does not work
• The timer has been stopped by pressing Timer On/Off.
In case it does not work, even the
action is taken as above.
• Press the Mode button on the front panel for 5
seconds in power ‘OFF’(standby), then it is returned the original
position (RESET)
The compact disc player does not
start playing
• The CD function has not been selected.
• The disc has been inserted face down or is either dirty or scratched.
• The laser sensor is dirty or dusty.
• The system has not been installed on a flat, horizontal surface.
• Condensation has formed in the player; leave the system in a warm,
airy room for at least one hour.
Reception is poor or no radio
stations are received at all
• The TUNER function has not been selected.
• The radio frequency has not been correctly selected.
• The aerial has been disconnected or is not facing the right way.
Turn it until you find the best orientation.
• You are in a building that blocks radio waves; you must use an
outside aerial.
If the above guidelines do not allow you to solve the problem, take a note of:
The model and serial numbers, normally printed on the rear of the system
Your warranty details
A clear description of the problem
Then contact your local dealer or SAMSUNG after-sales service.
20
EV-1(GB)-RDS
12/17/02
16:17
Page 22
Technical Specifications
SAMSUNG strives to improve its products at all times. Both the design specifications and these user
instructions are thus subject to change without notice.
RADIO
LW
Usable sensitivity
60 dB
AM (MW)
Signal/noise ratio
40 dB
Usable sensitivity
54 dB
Total harmonic distortion
2%
FM
Signal/noise ratio
62 dB
Usable sensitivity
5 dB
Total harmonic distortion
1.0 %
COMPACT DISC PLAYER
Frequency range
20 Hz - 20 KHz (± 1 dB)
Signal/noise ratio
90 dB (at 1 KHz) with filter
Distortion
0.05 % (at 1 KHz)
Channel separation
75 dB
Disc sizes
Diameter: 120 or 80 mm. Thickness: 1.2 mm
AMPLIFIER
Output power
Main(6 Ω) ........................................2 X 30 Watts RMS (total harmonic distortion : 10%)
Channel separation
50 dB
Signal/noise ratio
75 dB
GENERAL
Dimensions
21
350(W) x 60 (H) x 290(D) mm
EV-1(GB)-RDS
12/17/02
16:17
Page 23
THIS APPLIANCE IS MANUFACTURED BY:
ELECTRONICS
LECTRONICS
AH68-01169B