Empire Comfort Systems | VFSE-18-1 | Owner`s manual | Empire Comfort Systems VFSE-18-1 Owner`s manual

EMPIRE
INSTALLATION INSTRUCTIONS
AND OWNER'S MANUAL
Comfort Systems
Vented/Vent-Free Burner
UNVENTED GAS LOG HEATER OR
INTERMITTENT MODELS
VFSE-(18,24,30)-1
VARIABLE MODELS
VFSV-(16,18,24,30)-4
VENTED DECORATIVE APPLIANCE
VARIABLE MODELS
VFSV-(16,18,24,30)-4
GAS-FIRED
Installer: Leave this manual with the appliance.
Consumer: Retain this manual for future reference.
WARNING: If the information in these instructions
are not followed exactly, a fire or explosion may
result causing property damage, personal injury
or loss of life.
— Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use
any phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier, call the
fire department.
— Installation and service must be performed by a
qualified installer, service agency or the gas supplier.
This appliance may be installed in an aftermarket
permanently located, manufactured (mobile) home,
where not prohibited by local codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is not
convertible for use with other gases.
This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is installed. Provisions
for adequate combustion and ventilation air must be
provided. Refer to page 11.
WARNING: If not installed, operated and maintained
in accordance with the manufacturer's instructions,
this product could expose you to substances in fuel
or from fuel combustion which can cause death or
serious illness.
WATER VAPOR: A BY-PRODUCT OF UNVENTED ROOM
HEATERS
Water vapor is a by-product of gas combustion. An
unvented room heater produces approximately one (1)
ounce (30ml) of water for every 1,000 BTU's (.3KW's)
of gas input per hour. Refer to page 10.
Page 1
TABLE OF CONTENTS
Section Page
Quick Start Guide.........................................................................................................................3-4
Important Safety Information........................................................................................................... 5
Safety Information for Users of LP-Gas.......................................................................................... 6
Requirements for Canada............................................................................................................... 7
Introduction...................................................................................................................................... 8
Product Specification....................................................................................................................... 9
General Information....................................................................................................................... 10
Water Vapor: A By-Product of Unvented Room Heaters............................................................... 10
Provisions for Adequate Combustion & Ventilation Air.................................................................. 11
Clearances............................................................................................................................... 11-12
Combustible Material..................................................................................................................... 13
Fireplace Preparation.................................................................................................................... 13
Installing as a Vented Appliance.................................................................................................... 14
Before Fully Installing the Appliance............................................................................................. 14
Gas Supply.................................................................................................................................... 15
Placement of Glowing Embers and Lava Rock............................................................................. 16
Operation Instructions/Flame Appearance.................................................................................... 16
G6R-P3TAN5 Remote Control Instructions..............................................................................17-20
VFSE-(18,24,30) Lighting Instructions.......................................................................................... 21
RCAF-1031-4 Remote Control Instructions..............................................................................22-23
VFSV-(16,18,24,30) Lighting Instructions...................................................................................... 24
Pilot Flame Characteristics............................................................................................................ 25
Cleaning and Servicing................................................................................................................. 26
Wiring............................................................................................................................................ 26
Troubleshooting Symptoms - Possible Causes and Correction.................................................... 27
Parts List....................................................................................................................................... 28
Parts View..................................................................................................................................... 29
Master Parts Distributor List.......................................................................................................... 30
How To Order Repair Parts........................................................................................................... 30
Appliance Service History............................................................................................................. 31
Page 2
28092-1-0911
Quick Start Guide
To START the Fireplace:
If the pilot is NOT lit:
1. At the same time, press the “OFF” and high flame buttons and release once there is an
audible “beep” sound.
2. The pilot will ignite on the sixth beep. You may hear a clicking sound around the same
time as that beep, this is normal.
3. There will be a total of 14 beeps. The main burner will ignite approximately 15 seconds
after the pilot.
If the pilot IS lit.
1. To ignite the burner, press the high flame button (there will be a beep) for approximately
5 seconds until there is a soft click, then release the button.
To ADJUST the Flame Height
1. Press and hold the upper right button for a higher flame.
2. Press and hold the lower right button for a lower flame. Note: If you hold the lower right
button for too long, the flames on the main burner will go out, but the ignitor will stay lit.
To SHUT OFF the Fireplace
1. To completely shut off the burner and ignitor, press and hold the “OFF” button until the
unit “beeps.” The flames will go out on the burner once any lingering gas is used up.
2. To shut off the burner but keep the ignitor on, push the low flame button (bottom right) for
10 seconds and then release.
FOR MORE INFORMATION, SEE OPERATION INSTRUCTIONS.
VFSE Remote Quick Start Instructions: Cut out this page and keep it near your remote.
28092-1-0911
Page 3
THIS PAGE INTENTIONALLY LEFT BLANK
Page 4
28092-1-0911
IMPORTANT SAFETY INFORMATION
•
•
•
•
•
•
•
•
•
•
•
•
•
•
An unvented room heater having an input rating of more than
6,000 Btu per hour shall not be installed in a bathroom
An unvented room heater having an input rating of more than
10,000 Btu per hour shall not be installed in a bedroom or
bathroom.
Never burn solid fuels in a fireplace where a gas log set is
installed.
Due to high temperatures, the appliance should be located
out of traffic and away from furniture and draperies.
Do not place clothing or other flammable material on or near
the appliance.
Children and adults should be alerted to the hazards of high
surface temperature and should stay away to avoid burns or
clothing ignition.
Young children should be carefully supervised when they
are in the same room as the appliance.
This unit complies with ANSI Z21.11.2 Unvented Heaters
and it also complies with ANSI Z21.60 Decorative Vented
Appliances for Solid Fuel Burning Fireplaces. State or local
codes may only allow operation of this appliance in a vented
configuration. Check your state or local codes.
Correct installation of logs, proper location of the heater and
annual cleaning are necessary to avoid potential problems
with sooting. Sooting, resulting from improper installation
or operation, can settle on surfaces outside the fireplace.
Avoid any drafts that could alter burner flame patterns. Do
not allow fans to blow directly into the fireplace. Do not place
a blower inside burn box area of firebox. Ceiling fans may
create drafts that alter burner flame patterns. Sooting and
improper burning will occur as a result of drafts.
WARNING: Do not allow fans to blow directly into the fireplace.
Avoid any drafts that alter burner flame patterns.
WARNING: Do not use a blower insert, heat exchanger insert
or other accessory not approved for use with this heater.
Periodic examination and cleaning of the venting system of
the solid-fuel burning fireplace, including frequency of such
examination and cleaning, by a qualified agency.
The installation must conform with local codes or, in the
absence of local codes, with the National Fuel Gas Code,
ANSI Z223.1/NFPA54.
WARNING
When used without adequate combustion and ventilation air, heater
may give off CARBON MONOXIDE, an odorless, poisonous gas.
Do not install heater until all necessary provisions are made for
combustion and ventilation air. Consult the written instructions
provided with the heater for information concerning combustion
and ventilation air. In the absence of instructions, refer to the
National Fuel Gas Code, ANSI Z223.1/NFPA 54, Air for Combustion
and Ventilation, or applicable local codes.
This heater is equipped with a PILOT LIGHT SAFETY SYSTEM
designed to turn off the heater if not enough fresh air is available.
DO NOT TAMPER WITH PILOT LIGHT SAFETY SYSTEM!
If heater shuts off, do not relight until you provide fresh air.
If heater keeps shutting off, have it serviced. Keep burner and control
compartment clean.
28092-1-0911
•
•
•
•
•
•
•
•
•
•
•
NOTE: Installation and repair should be done by a qualified
service person. The appliance should be inspected before
use and at least annually by a qualified service person. More
frequent cleaning may be required due to excessive lint from
carpeting, bedding material, etc. It is imperative that the control compartment, burners and circulating air passageways
of the appliance be kept clean.
Any safety screen or guard removed for servicing an appliance must be replaced prior to operating the appliance.
Provide adequate combustion and ventilation air.
The flow of combustion and ventilation air MUST NOT be
obstructed.
Provide adequate clearances around air openings into the
combustion chamber and adequate accessibility clearance
for servicing and proper operation. NEVER obstruct the front
opening of the appliance.
An unvented room heater intended for installation in a
solid-fuel burning fireplace shall comply with the following
instructions.
A fireplace screen must be in place when the appliance is
operating and, unless other provisions for combustion air are
provided, the screen shall have an opening(s) for introduction
of combustion air.
Solid-fuels shall not be burned in a masonry or UL 127
factory-built fireplace in which an unvented room heater is
installed.
Any glass doors shall be fully opened when the appliance is
in operation.
Any outside air ducts and/or ash dumps in the fireplace shall
be permanently closed at time of appliance installation.
WARNING: Failure to keep the primary air opening(s) of
the burner(s) clean may result in sooting and property
damage.
WARNING: Before installing in a solid-fuel burning fireplace,
the chimney flue and firebox must be cleaned of soot, creosote,
ashes and loose paint by a qualified chimney cleaner.
CARBON MONOXIDE POISONING MAY LEAD TO DEATH.
Early signs of carbon monoxide poisoning resemble the flu, with
headache, dizziness and/or nausea. If you have these signs, heater
may not be working properly. Get fresh air at once! Have heater
serviced.
Some people – pregnant women, persons with heart or lung disease,
anemia, those under the influence of alcohol, those at high altitudes
– are more affected by carbon monoxide than others.
The pilot light safety system senses the depletion of oxygen at its
location. If this heater is installed in a structure having a high vertical
dimension, the possibility exists that the oxygen supply at the higher
levels will be less than that at the heater. In this type of application,
a fan to circulate the structure air will minimize this effect. The use
of this fan will also improve the comfort level in the structure. When
a fan is used to circulate air, it should be located so that the air flow
is not directed at the burner.
Page 5
SAFETY INFORMATION FOR USERS OF LP-GAS
Propane (LP-Gas) is a flammable gas which can cause fires
and explosions. In its natural state, propane is odorless and
colorless. You may not know all the following safety precautions
which can protect both you and your family from an accident.
Read them carefully now, then review them point by point
with the members of your household. Someday when there
may not be a minute to lose, everyone's safety will depend
on knowing exactly what to do. If, after reading the following
information, you feel you still need more information, please
contact your gas supplier.
LP-GAS WARNING ODOR
If a gas leak happens, you should be able to smell the gas because of the odorant put in the LP-Gas.
That's your signal to go into immediate action!
•
•
•
•
•
Do not operate electric switches, light matches, use your
phone. Do not do anything that could ignite the gas.
Get everyone out of the building, vehicle, trailer, or area. Do
that IMMEDIATELY.
Close all gas tank or cylinder supply valves.
LP-Gas is heavier than air and may settle in low areas such
as basements. When you have reason to suspect a gas leak,
keep out of basements and other low areas. Stay out until
firefighters declare them to be safe.
Use your neighbor's phone and call a trained LP-Gas service
•
person and the fire department. Even though you may not
continue to smell gas, do not turn on the gas again. Do not
re-enter the building, vehicle, trailer, or area.
Finally, let the service man and firefighters check for escaped
gas. Have them air out the area before you return. Properly
trained LP-Gas service people should repair the leak, then
check and relight the gas appliance for you.
NO ODOR DETECTED - ODOR FADE
Some people cannot smell well. Some people cannot smell the
odor of the chemical put into the gas. You must find out if you
can smell the odorant in propane. Smoking can decrease your
ability to smell. Being around an odor for a time can affect your
sensitivity or ability to detect that odor. Sometimes other odors in
the area mask the gas odor. People may not smell the gas odor
or their minds are on something else. Thinking about smelling a
gas odor can make it easier to smell.
The odorant in LP-gas is colorless, and it can fade under some
circumstances. For example, if there is an underground leak, the
movement of the gas through soil can filter the odorant. Odorants
in LP-Gas also are subject to oxidation. This fading can occur if
there is rust inside the storage tank or in iron gas pipes.
The odorant in escaped gas can adsorb or absorb onto or into walls,
masonry and other materials and fabrics in a room. That will take
some of the odorant out of the gas, reducing its odor intensity.
LP-Gas may stratify in a closed area, and the odor intensity could
vary at different levels. Since it is heavier than air, there may be
more odor at lower levels. Always be sensitive to the slightest gas
odor. If you detect any odor, treat it as a serious leak. Immediately
go into action as instructed earlier.
SOME POINTS TO REMEMBER
•
Learn to recognize the odor of LP-gas. Your local LP-Gas
Dealer can give you a "Scratch and Sniff" pamphlet. Use it to
find out what the propane odor smells like. If you suspect that
your LP-Gas has a weak or abnormal odor, call your LP-Gas
Dealer.
•
If you are not qualified, do not light pilot lights, perform service,
or make adjustments to appliances on the LP-Gas system. If
you are qualified, consciously think about the odor of LP-Gas
prior to and while lighting pilot lights or performing service or
making adjustments.
•
Sometimes a basement or a closed-up house has a musty
smell that can cover up the LP-Gas odor. Do not try to light
pilot lights, perform service, or make adjustments in an area
where the conditions are such that you may not detect the
odor if there has been a leak of LP-Gas.
•
Odor fade, due to oxidation by rust or adsorption on walls of
new cylinders and tanks, is possible. Therefore, people should
be particularly alert and careful when new tanks or cylinders
are placed in service. Odor fade can occur in new tanks, or
reinstalled old tanks, if they are filled and allowed to set too
long before refilling. Cylinders and tanks which have been
out of service for a time may develop internal rust which will
Page 6
cause odor fade. If such conditions are suspected to exist,
a periodic sniff test of the gas is advisable. If you have any
question about the gas odor, call your LP-gas dealer. A
periodic sniff test of the LP-gas is a good safety measure
under any condition.
•
If, at any time, you do not smell the LP-Gas odorant and you
think you should, assume you have a leak. Then take the same
immediate action recommended above for the occasion when
you do detect the odorized LP-Gas.
•
If you experience a complete "gas out," (the container is under no vapor pressure), turn the tank valve off immediately.
If the container valve is left on, the container may draw in
some air through openings such as pilot light orifices. If this
occurs, some new internal rusting could occur. If the valve is
left open, then treat the container as a new tank. Always be
sure your container is under vapor pressure by turning it off
at the container before it goes completely empty or having it
refilled before it is completely empty.
28092-1-0911
REQUIREMENTS FOR CANADA
This unit cannot be installed in a UNVENTED application, this
unit can only be installed as a VENTED application with these
requirements.
IMPORTANT SAFETY INFORMATION
This unit complies with ANSI Z21.60 and CGA 2.26 Decorative
Gas Appliances For Installation In Solid Fuel Burning Fireplaces.
Do not burn wood or solid fuels in a fireplace where a decorative
gas log set is installed. This appliance is for installation only in
a solid fuel burning fireplace, masonry fireplace or manufactured
fireplace.
Warning: Any modification to this gas log set or to controls can
be dangerous. Improper installation or use of the gas log set can
cause serious injury or death from fire, burns, explosion or carbon
monoxide poisoning.
1. Please follow all local codes regarding installation, combustion and ventilation air or in the absence of local codes follow
the National Fuel Gas Code ANSI Z223.1(U.S. installation), or
CAN/CGA-B149, Installation Code (Canada installation).
2. Proper installation, burner pan location and log placement is
important to achieve optimum look and performance of your
gas log set. The logs have been designed for easy location
and placement on the grate and must be followed for proper
operation.
3. Do not operate this log set with glass doors in the closed position. A fireplace screen must be in place when the log set
is burning. Adequate combustion air must be provided for
proper venting. All flames should go up and out the top of the
firebox into the flue vent. If any flames float or curl forward into
the room do not operate appliance. Check for an open flue
and adequate combustion air into the room. A damper clamp
must be installed on the firebox damper to maintain an open
flue vent condition. Refer to page 14 INSTALLING DAMPER
CLAMP
4. Young children must be carefully supervised when they are in
the same room as the gas log while in operation. Do not place
stockings, clothing or any flammable material above or near
the fireplace.
5. Do not substitute or use materials other than those supplied
for use with the log set.
6. Also refer to IMPORTANT SAFETY INFORMATION on page
5 of this manual
28092-1-0911
WARNING; DO NOT OPERATE THIS GAS LOG SET WITH
GLASS DOORS CLOSED
•
•
•
•
•
•
•
•
•
•
•
•
•
Clothing or other flammable material should not be placed on
or near the appliance.
Do not place trash or other articles on the log set during operation.
During manufacturing, fabricating and shipping, various components of this appliance are treated with certain oils, films or
bonding agents. These bonding agents are not harmful but
may produce annoying smoke and smells as they are burned
off during initial operation of the appliance. This is a normal
temporary occurrence. A window should be opened during the
initial bake out period.
Keep burner and control compartment clean.
WARNING: Before installing in a solid fuel burning fireplace,
the chimney flue and firebox must be cleaned of soot, creosote, ashes and loose paint by a qualified chimney cleaner.
Installation and repair should be done by a qualified service
person. The appliance should be inspected before use and
at least annually by a qualified service person. More frequent
cleaning may be required due to excessive lint from carpeting,
bedding materials, etc. It is imperative that control compartments, burners and circulating air passageways of the appliance be kept clean.
Do not put anything around the fireplace that will obstruct the
flow of ventilation air.
Do keep the appliance area clear and free from combustible
material, gasoline and other flammable vapors and liquids.
A yearly examination and cleaning of the venting system of
the solid-fuel burning fireplace must be performed by a qualified agency.
Do make a periodic visual check of pilot and burners. Clean
and replace damaged parts.
Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control which has been under water.
Never burn solid fuels in fireplace where a gas log set is installed.
This unit complies with ANSI Z21.60 Decorative Vented Appliances for Solid Fuel Burning Fireplaces. State or local codes
may only allow operation of this appliance in a vented configuration. Check your state or local codes.
Page 7
INTRODUCTION
IMPORTANT: Read all instructions carefully before starting
installation. Failure to follow these installation instructions may
result in a possible fire hazard and will void the warranty.
Save this manual for future reference.
Please read this manual before installing and using the
appliance.
Instructions to Installer
1. Installer must leave instruction manual with owner after
installation.
2. Installer must have owner fill out and mail warranty card supplied
with unvented room heater/vented decorative appliance.
3. Installer should show owner how to start and operate unvented
room heater/vented decorative appliance.
Always consult your local Building Department regarding regulations,
codes or ordinances which apply to the installation of an unvented
room heater/vented decorative appliance.
This appliance may be installed in an aftermarket* manufactured
(mobile) home, where not prohibited by state or local codes.
*Aftermarket: Completion of sale, not for purpose of resale, from
the manufacturer.
This appliance is only for use with the type of gas indicated on the
rating plate. This appliance is not convertible for use with other
gases.
New Installation
Solid-fuels shall not be burned in a fireplace where a vented decorative
appliance is installed.
A vented decorative appliance must be installed only in a solidfuel burning fireplace with a working flue and constructed of
noncombustible material.
Any alteration of the original design, installed other than as
shown in these instructions or use with a type of gas not
shown on the rating plate is the responsibility of the person
and company making the change.
Important
All correspondence should refer to complete Model Number, Serial
Number and type of gas.
Attention: During initial use of log you will detect an odor as
the log is cured.
Notice: During initial firing of this unit, its paint will bake out, and
smoke will occur. To prevent triggering of smoke alarms, ventilate
the room in which the unit is installed.
WARNING: This appliance is for installation only in a solid-fuel
burning masonry or UL 127 factory-built fireplace or in a listed
ventless firebox enclosure. It has been design certified for
these installations. Exception: DO NOT install this appliance
in a factory-built fireplace that includes instructions stating
it has not been tested or should not be used with unvented
gas logs.
WARNING: Any modification to this unvented gas heater or
its controls can be dangerous. Improper installation or use
of the heater can cause serious injury or death from fire,
burns, explosion or carbon monoxide poisoning.
Well Head Gas Installations
Some natural gas utilities use "well head" gas. This may affect the
Btu output of the unit. Contact the gas company for the heating value.
Contact the manufacturer or your gas company before changing
spud/orifice size.
ACCESSORIES
Accessory
Description
Color
For use with VFSE and VFSV models
EK-1
Embers Kit
ELH-1
Fireplace Hood for Vent-Free Logs
Black
ELH-2
Fireplace Hood for Vent-Free Logs
Brass
For use with VFSE models ONLY
AD1106V
Note:
Page 8
AC/DC Adapter
Thermostats are for Vent-Free Applications only.
28092-1-0911
PRODUCT SPECIFICATIONS
Natural Gas
Note:
Propane Gas
VFSE
VFSV
VFSE
VFSV
Regulator pressure setting
3.5" W.C.
4.0" W.C.
10.0" W.C.
10.0" W.C.
Gas inlet pressure
Max.
10.5" W.C.
10.5" W.C.
13.0" W.C.
13.0" W.C.
Min.
7.0" W.C.
7.0" W.C.
11.0" W.C.
11.0" W.C.
Model
Gas
Valve Type
BTUH Max. Rate
BTUH Med. Rate
BTUH Min. Rate
VFSE-18
Natural
Intermittent
32,000
—
26,000
VFSE-18
Propane
Intermittent
32,000
—
26,000
VFSE-24
Natural
Intermittent
36,000
—
28,800
VFSE-24
Propane
Intermittent
36,000
—
28,800
VFSE-30
Natural
Intermittent
38,000
—
30,000
VFSE-30
Propane
Intermittent
38,000
—
30,000
VFSV-16
Natural
Variable
25,000
—
18,000
VFSV-16
Propane
Variable
22,500
—
17,000
VFSV-18
Natural
Variable
32,000
—
21,000
VFSV-18
Propane
Variable
32,000
—
21,000
VFSV-24
Natural
Variable
36,000
—
24,000
VFSV-24
Propane
Variable
36,000
—
24,000
VFSV-30
Natural
Variable
38,000
—
27,000
VFSV-30
Propane
Variable
38,000
—
27,000
Thermostats are for Vent-Free Applications only.
28092-1-0911
Page 9
GENERAL INFORMATION
This is an unvented gas-fired heater. It uses air (oxygen) from the
room in which it is installed. Provisions for adequate combustion
and ventilation air must be provided.
Keep room area clear and free from combustible materials, gasoline
and other flammable vapors and liquids.
Unvented gas heaters are a supplemental zone heater. They are not
intended to be a primary heating appliance. Water vapor produced
by an unvented heater can create moisture problems in a home
when operated for extended periods of time.
During manufacturing, fabricating and shipping, various components
of this appliance are treated with certain oils, films or bonding agents.
These chemicals are not harmful but may produce annoying smoke
and smells as they are burned off during the initial operation of the
appliance; possibly causing headaches or eye or lung irritation. This
is a normal and temporary occurrence.
The initial break-in operation should last 2 to 3 hours with the burner
at the highest setting. Provide maximum ventilation by opening
windows or doors to allow odors to dissipate. Any odors remaining
after this initial break-in period will be slight and will disappear with
continued use.
This appliance must not be used with glass doors in the closed
position. This can lead to pilot outages and severe sooting outside
the fireplace.
Do not use this room heater if any part has been under water.
Immediately call a qualified service technician to inspect the room
heater and replace any part of the control system and any gas
control which has been under water.
WARNING: This appliance is equipped for (natural or
propane) gas. Field conversion is not permitted.
Handle the gas log burner assembly by the grate and legs only.
Do not pick the unit up by the burner.
Gloves are recommended when handling logs to prevent skin
irritation. Logs are fragile - Handle with care.
Qualified Installing Agency
Installation and replacement of gas piping, gas utilization equipment or accessories and repair and servicing of equipment shall be
performed only by a qualified agency. The term "qualified agency"
means any individual, firm, corporation, or company that either in
person or through a representative is engaged in and is responsible
for (a) the installation, testing, or replacement of gas piping or (b) the
connection, installation, testing, repair, or servicing of equipment;
that is experienced in such work; that is familiar with all precautions
required, and that has complied with all the requirements of the
authority having jurisdiction.
State of Massachusetts: The installation must be made
by a licensed plumber or gas fitter in the Commonwealth of
Massachusetts.
Sellers of unvented propane or natural gas-fired supplemental
room heaters shall provide to each purchaser a copy of 527
CMR-30 upon sale of the unit.
The installation must conform with local codes or, in the absence of
local codes, with the National Fuel Gas Code, ANSI Z223.1.*
*Available from the American National Standards Institute, Inc. 11
West 42nd St., New York, N.Y. 10018.
High Altitudes: For altitudes/elevation above 2,000 feet ratings
should be reduced at the rate of 4 percent for each 1,000 feet above
sea level. Contact the manufacturer.
Before you get started
Carefully inspect the contents for shipping damage. If any parts are
missing or damaged, immediately inform the dealer from whom you
purchased the appliance. Do not attempt to install any part of the
appliance unless you have all parts in good condition.
Make sure you have received all parts:
Check your packing list to verify that all listed parts have been
received. You should have the following:
• Gas log grate/burner assembly.
• Two (2) masonry anchoring screws and two (2) 10 x 1/2" black
sheet metal anchoring screws.
• Plastic bag containing glowing embers (rock wool) for burner
coverage.
• Plastic bag containing lava rock.
• Remote Kit
WATER VAPOR: A BY-PRODUCT OF UNVENTED ROOM HEATERS
Water vapor is a by-product of gas combustion. An unvented room
heater produces approximately one (1) ounce (30ml) of water for
every 1,000 BTU's (.3KW's) of gas input per hour.
Unvented room heaters must be used as supplemental heat (a
room) rather than a primary heat source (an entire house). In most
supplemental heat applications, the water vapor does not create a
problem. In most applications, the water vapor enhances the low
humidity atmosphere experienced during cold weather.
Page 10
The following steps will help insure that water vapor does not
become a problem.
1. Be sure the heater is sized properly for the application, including
ample combustion air and circulation air.
2. If high humidity is experienced, a dehumidifier may be used to
help lower the water vapor content of the air.
3. Do not use an unvented room heater as the primary heat source
(an entire house).
28092-1-0911
PROVISIONS FOR ADEQUATE COMBUSTION & VENTILATION AIR
This heater shall not be installed in a confined space unless provisions are provided for adequate combustion and ventilation air.
A confined space is an area with volume less than 50 cubic feet per
1,000 Btuh of the combined input rates of all appliances drawing
combustion air from that space. Small areas such as equipment
rooms are confined spaces. Furnaces installed in a confined space
which supply heated air to areas outside the space must draw return
air from outside the space through tightly sealed return air ducts. A
confined space must have 2 openings into the space for combustion air. One opening must be within 12 inches of the ceiling and
the other must be within 12 inches of the floor. The required sizing
of these openings is determined by whether inside or outside air is
used to support combustion, the method by which the air is brought
to the space (vertical or horizontal duct) and by the total input rate
of all appliances in the space.
Unusually Tight Construction
The air that leaks around doors and windows may provide enough
fresh air for combustion and ventilation. However, in buildings of
unusually tight construction, you must provide additional fresh air.
Unusually tight construction is defined as construction
where:
a. Walls and ceilings exposed to the outside atmosphere have
a continuous water vapor retarder with a rating of one perm
or less with openings gasketed or sealed, and
b. Weatherstripping has been added on openable windows and
doors, and
c. Caulking or sealants are applied to areas such as joints
around window and door frames, between sole plates and
floors, between wall-ceiling joints, between wall panels, at
penetrations for plumbing, electrical, and gas lines, and at
other openings.
If your home meets all of the three criteria above, you must
provide additional fresh air.
Warning: If the area in which the heater may be operated is smaller
than that defined as an unconfined space or if the building is of
unusually tight construction, provide adequate combustion and
DIVIDER
FIREPLACE
H
L2
L1
W
ventilation air by one of the methods described in the National Fuel
Gas Code, ANSI Z223.1/NFPA 54, Air for Combustion and Ventilation, or applicable local codes.
Example of Large Room with 1/2 Wall divider.
Figure 1
The following formula can be used to determine the maximum heater
rating per the definition of unconfined space:
(L1 + L2)FT x (W)FT x (H)FT
x 1000
50
If the area in which the heater may be operated is smaller than that
defined as an unconfined space, provide adequate combustion and
ventilation air by one of the methods described in the National Fuel
Gas Code, ANSI Z223.1, NFPA54.
Adhere to all codes, or in their absence, the latest edition of THE
NATIONAL FUEL GAS CODE ANSI Z223.1/NFPA54 which can be
obtained from:
American National Standards InstituteNational Fire Protection Association, Inc.
11 West 42nd St.
Batterymarch Park
New York, NY 10018
Quincy, MA 02269
Btu/Hr =
CLEARANCES
Minimum Dimensions For Solid Fuel Burning Fireplaces UL127
Factory Built Fireplaces (Figure 2)
Model
A
B
C
D
VFSE-18
17"
14"
28"
17"
VFSE-24
23"
14"
30"
18"
VFSE-30
26"
14"
34"
20"
VFSV-16
18"
11 1/2"
24"
18"
VFSV-18
17"
14"
28"
17"
VFSV-24
23"
14"
30"
18"
VFSV-30
26"
14"
34"
20"
Follow these instructions to ensure safe installation.
Failure to follow instructions exactly can create a fire hazard.
The dimensions shown and defined in the fireplace manufacturer’s
instructions are minimum clearances to maintain in installing this
heater. Left and right clearances are determined when facing the
front of the heater.
Glass Doors
Make sure that glass doors are open during all operations of
the logset. The opening of the glass door frame should be the
dimension used for the minimum front opening of the firebox.
28092-1-0911
Figure 2
Page 11
CLEARANCES (continued)
Sidewall & Ceiling Clearances (Figure 3)
N o n c o m b u s t i b l e Requirements for Safe Installation
Material Distance
12" or more
Noncombustible material
Less than 12"
Noncombustible material must be extended to at least 8" with the installation
of the optional fireplace hood. If you cannot extend noncombustible material at
least 8", you must operate heater with
flue damper open.
Mantel Clearances with Hood (Figure 5)
You must have noncombustible materials above the fireplace
opening. Noncombustible material must extend at least 8" above
fireplace opening. With sheet metal, you must have noncombustible
material behind it.
Figure 3
The sides of the fireplace opening must be 6" from any combustible
wall. The ceiling must be at least 36" (for the 16" log) and 41" (for
18", 24" and 30" logs) from the fireplace opening.
Mantel Clearances Without Hood (Figure 4)
You must have noncombustible materials above the fireplace
opening. Noncombustible material must extend at least 12" above
fireplace opening. With sheet metal, you must have noncombustible
material behind it.
Heat resistant materials such as slate and marble must be at least
1/2" thick. Sheet metal should not be installed onto combustible
material.
Example: A mantel may project from the wall a maximum of 2" at
a minimum of 13 1/2" above the opening, and a maximum of 6" at
a minimum of 15" above the opening.
Heat resistant materials such as slate and marble must be at least
1/2" thick. Sheet metal should not be installed onto combustible
material.
Figure 5
If your installation does not meet the above minimum clearances,
you must proceed to one of the following steps:
• Operate the heater with the flue damper open. See page 14
for Installing as a Vented Appliance.
• Raise the mantel to the proper height.
• Remove the mantel.
Floor Clearance (Figure 6)
If installing heater at floor level, the minimum distance to combustibles is “0” inches.
Figure 4
If your installation does not meet the above clearances, you must
proceed to one of the following steps:
• Use a hood
• Operate the heater with flue damper open. See page 14 for
Installing as a Vented Appliance.
• Raise the mantel to the proper height.
• Remove the mantel.
HEATER IN FIREPLACE
OR FIREBOX
COMBUSTIBLE
MATERIAL
Figure 6
Page 12
28092-1-0911
COMBUSTIBLE MATERIAL
Do not attach combustible material to the mantel of your fireplace.
This is a fire hazard.
No greeting card, stockings or ornamentation of any type should be
placed on or attached to the fireplace. This is a heating appliance.
The flow of heat can ignite combustibles.
Figure 7
Figure 8
FIREPLACE PREPARATION
•
•
Turn off gas supply to fireplace or firebox.
Have the fireplace floor and chimney professionally cleaned to
remove ashes, soot, creosote or other obstructions.
Have this cleaning performed annually after installation.
• Seal any fresh air vents or ash clean-out doors located on floor
or wall of fireplace. If not, drafting may cause pilot
outage or sooting. Use a heat-resistant sealant. Do not seal
chimney flue damper.
Install and operate the appliance as directed in this manual.
FOR MASONRY BUILT FIREPLACES
FREE OPENING AREA OF CHIMNEY DAMPER FOR VENTING
COMBUSTION PRODUCTS FROM DECORATIVE APPLIANCES
FOR INSTALLATION IN SOLID FUEL BURNING FIREPLACES
Appliance Input Rate (BTU/hr)
20
Chimney
Height* (ft)
FOR FACTORY BUILT FIREPLACES
FREE OPENING AREA OF CHIMNEY DAMPER FOR VENTING
COMBUSTION PRODUCTS FROM DECORATIVE APPLIANCES
FOR INSTALLATION IN SOLID FUEL BURNING FIREPLACES
Appliance Input Rate (BTU/hr)
20
Chimney
Height* (ft)
30
40
Minimum Opening** (sq. in.)
10
11.3
16.6
22.1
15
8.6
12.6
17.3
20
7.5
10.8
14.5
25
6.6
9.6
12.6
30
6.2
9.1
11.3
35
5.7
8.0
10.8
40
5.3
7.5
10.2
30
40
Minimum Opening** (sq. in.)
6
17.6
25.7
33.8
8
16.5
23.7
31.2
10
15.1
21.7
28.7
15
14.1
19.9
26.1
20
12.9
18.5
23.7
30
12.2
16.9
21.6
*
Height is from hearth to top of chimney and the minimum height
is 6 feet.
** Chart shows minimum opening (sq. in.) for given height and
input rate.
* Height is from hearth to top of chimney and the minimum
height is 10 feet.
** Chart shows minimum opening (sq. in.) for given height and
input rate.
28092-1-0911
Page 13
INSTALLING AS A VENTED APPLIANCE
Notice: (Damper Clamp Installation)
When installing your log set as a vented installation the damper
clamp must be used.
When installing your log set as a vent-free installation the damper
clamp can be used to eliminate the potential for odors when burning
the logs for the first time.
Installing Damper Clamp (Figure 9)
Remove all ashes or other debris from the fireplace. If the fireplace
is equipped with an ash dump be sure to seal the door with furnace
cement or high temperature silicone. Be sure to check the damper
for proper operation and verify that the flue passageway is open.
Place the clamp over the lip of the damper and tighten the hold
down bolt until the clamp is securely attached to the damper. This
will prevent the damper from accidentally closing.
Manual and millivolt controlled gas logs may be installed as a vented
decorative log set in compliance with ANSI Z21.60 and National
Fuel Gas Code. When the gas logs are operated with the damper
open, noncombustible material and minimum mantel requirements
do not apply.
Figure 9
BEFORE FULLY INSTALLING THE APPLIANCE
•
•
Turn off the gas supply to the fireplace or firebox.
Seal any fresh air vents and/or ash clean-out doors located on
the floor or wall of the fireplace. If left unsealed, drafting may
cause pilot outage or sooting. Use a heat resistant sealant. Do
not seal the chimney flue damper.
Before installing in a solid fuel burning fireplace, the chimney flue
and firebox must be cleaned of soot, creosote, ashes and loose
paint by a qualified chimney cleaner.
You must secure the gas log heater to the fireplace floor. If
not, the entire unit may move when you adjust the controls.
Movement of unit may cause shifting of the gas logs which
leads to sooting and improper burning. Grate movement
could cause a gas leak.
Assembly Procedure: (Figure 10)
1. Center the gas log unit in the fireplace or firebox. Make certain
the front feet of the grate sit inside the front edge of the fireplace
or firebox.
2. An anchor hole is provided in the two bottom side members of
the grate frame. After centering the grate correctly, mark the
hole positions on the fireplace/firebox floor. Drill two (2) 5/32"
diameter holes approximately 1 1/2" deep for masonry screws
or 1/8" hole for sheet metal screws.
3. Anchor the grate to the fireplace/firebox floor using the screws
provided. Refer to Figure 10.
Proper installation of the grate is essential to prevent any movement of the gas logs and controls during operation.
Special care is required if you are installing the unit into a
sunken fireplace. You must raise the fireplace floor to allow
access to gas log controls. This will insure adequate air flow
and guard against sooting. Raise the fireplace floor using
noncombustible materials.
Figure 10
Page 14
28092-1-0911
GAS SUPPLY
Check all local codes for requirements, especially for the size and
type of gas supply line required.
Recommended Gas Pipe Diameter
Pipe Length
Schedule 40 Pipe
Inside Diameter
Tubing, Type L
Outside Diameter
Nat.
L.P.
Nat.
L.P.
0-10 feet
0-3 meters
1/2”
12.7mm
3/8”
9.5mm
1/2”
12.7mm
3/8”
9.5mm
10-40 feet
4-12 meters
1/2”
12.7mm
1/2”
12.7mm
5/8”
15.9mm
1/2”
12.7mm
40-100 feet
13-30 meters
1/2”
12.7mm
1/2”
12.7mm
3/4”
19mm
1/2”
12.7mm
100-150 feet
31-46 meters
3/4”
19mm
1/2”
12.7mm
7/8”
22.2mm
3/4”
19mm
Note: Never use plastic pipe. Check to confirm whether your local
codes allow copper tubing or galvanized.
Note: Since some municipalities have additional local codes, it is
always best to consult your local authority and installation code.
Installing a New Main Gas Cock
Each appliance should have its own manual gas cock.
A manual main gas cock should be located in the vicinity of the unit.
Where none exists, or where its size or location is not adequate,
contact your local authorized installer for installation or relocation.
Compounds used on threaded joints of gas piping shall be resistant
to the action of liquefied petroleum gases. The gas lines must be
checked for leaks by the installer. This should be done with a soap
solution watching for bubbles on all exposed connections, and if
unexposed, a pressure test should be made.
Never use an exposed flame to check for leaks. Appliance must
be disconnected from piping at inlet of control valve and pipe
capped or plugged for pressure test. Never pressure test with
appliance connected; control valve will sustain damage!
A gas valve and ground joint union should be installed in the gas
line upstream of the gas control to aid in servicing. It is required by
the National Fuel Gas Code that a drip line be installed near the gas
inlet. This should consist of a vertical length of pipe tee connected
into the gas line that is capped on the bottom in which condensation
and foreign particles may collect.
Figure 11
The use of the following gas connectors is recommended:
— ANS Z21.24 Appliance Connectors of Corrugated Metal Tubing
and Fittings
— ANS Z21.45 Assembled Flexible Appliance Connectors of Other
Than All-Metal Construction
The above connectors may be used if acceptable by the authority
having jurisdiction. The state of Massachusetts requires that a flexible
appliance connector cannot exceed three feet in length.
Pressure Testing of the Gas Supply System
1. To check the inlet pressure to the gas valve, a 1/8" (3.175mm)
N.P.T. plugged tapping, accessible for test gauge connection,
must be placed immediately upstream of the gas supply
connection to the appliance.
2. The appliance and its individual shutoff valve must be
disconnected from the gas supply piping system during any
pressure testing of that system at test pressures in excess of
1/2 psig (3.5 kPa).
3. The appliance must be isolated from the gas supply piping
system by closing its individual manual shutoff valve during
any pressure testing of the gas supply piping system at test
pressures equal to or less than 1/2 psig (3.5 kPa).
Attention! If one of the procedures results in pressures in excess
of 1/2 psig (14" w.c.) (3.5 kPa) on the appliance gas valve, it will
result in a hazardous condition.
28092-1-0911
Page 15
PLACEMENT OF GLOWING EMBERS AND LAVA ROCK
Placement of the glowing embers (rock wool) is very individual
and light coverage will provide your best effects. We recommend
separation of the rock wool by hand and make your coverage as
light and fluffy as possible.
Place just enough embers on the burner to obtain the glow and a
gold, yellow flame.
Do not place embers (rock wool) over large ports in rear portion
of burner.
Placing Lava Rock in Front of Burner on Fireplace Floor
Spread lava rocks on fireplace floor in front of the burner pan. The
lava rocks are for decorative effect and are not required for fireplace
operation.
ATTENTION: DO NOT PLACE LAVA ROCKS ON BURNER,
LOGS OR ROCK WOOL. THE LAVA ROCKS SHOULD ONLY
BE PLACED ON THE FIREPLACE FLOOR.
Rock wool should not be placed in the area of the pilot assembly.
Replacement of loose material (glowing embers) must be purchased
from Empire Comfort Systems, Inc. Application of excess loose
material (glowing embers) may adversely affect performance of
the heater. WARNING: All previously applied loose material must
be removed prior to reapplication.
Refer to Parts List, Page 28 to order loose material (rock wool).
OPERATION INSTRUCTIONS/FLAME APPEARANCE
Flames from the pilot (rear right back side of the pan burner) as
well as the main flame should be visually checked as the log set
is installed.
In normal operation at full rate after 10 to 15 minutes, the flame
appearance should be sets of yellow flames.
NOTE: All flames will be random by design, flame height will go
up and down.
Glowing embers (rock wool) can cover the pan burner in between
the front and middle logs, but very little is necessary to cover this
area. Excess ember material causes the yellow flame to become
orange and stringy. Apply just enough to obtain slow glow and a
gold yellow flame.
Avoid any drafts that alter burner flame patterns. Do not allow fans to
blow directly into fireplace. Do not place a blower inside the burner
area of the firebox. Ceiling fans may create drafts that alter flame
patterns. Sooting and improper burning will result.
Intermittent - Figure 12
During manufacturing, fabricating and shipping, various components
of this appliance are treated with certain oils, films or bonding agents.
These chemicals are not harmful, but may produce annoying smoke
and smells as they are burned off during the initial operation of the
appliance, possibly causing headaches or eye or lung irritation. This
is a normal and temporary occurrence.
The initial break-in operation should last 2 to 3 hours with the
burner at the highest setting. Provide maximum ventilation by
opening windows or doors to allow odors to dissipate. Any odors
remaining after this initial break-in will be slight and will disappear
with continued use.
Page 16
Variable - Figure 13
28092-1-0911
G6R-P3TAN5 REMOTE CONTROL INSTRUCTIONS
NOTE: This remote is for use on VFSE Models ONLY.
AUTOMATIC OPERATION
WARNING
Wiring of valve and receiver must be completed before starting
ignition. Failure to do so could damage the electronics.
NOTE: This remote handset and receiver are not interchangeable with previous versions.
For all lighting/ignition instructions please refer to
appliance manufacturer’s instructions.
GENERAL NOTES
Radio Frequency Remote
433.92 MHz for Europe;
315 MHz for U.S. (FCC ID: RTD-G6R) and for Canada (IC:
4943A-G6R).
SETTING THE ELECTRONICS CODE
Radio Frequency Remote
A code is selected automatically for all Mertik Maxitrol
electronics from among 65,000 random codes available. The
receiver has to learn the code of the handset:
• Press and hold the receiver’s reset button until you hear two
(2) acoustic signals. After the second, longer acoustic signal,
release the reset button.
• Within the subsequent 20 seconds press the small flame)
button on the remote handset until you hear an additional long
signal confirming the code is set.
NOTE: This is a one time setting only, and is not required when
changing the batteries in the remote or receiver.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired
operation. Changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Batteries - Remote Handset:
1 x 9V block (quality alkaline recommended)
Batteries - Receiver:
4 x 1.5V “AA” (quality alkaline recommended)
An AC Mains Adapter may be used instead of
batteries (only the Mertik Maxitrol or an AC Mains
Adapter approved by Mertik Maxitrol can be used).
NOTE: During a power outage the AC Mains Adapter must be
unplugged from the receiver to operate in the battery
mode.
28092-1-0911
TO TURN ON APPLIANCE
WARNING
When pilot ignition is confirmed, motor turns automatically
to maximum flame height.
•
•
Turn MANUAL knob to the ON, full counterclockwise
position.
Place ON/OFF switch (if equipped in (ON position).
Page 17
G6R-P3TAN5 REMOTE CONTROL INSTRUCTIONS
Standard, Display, Timer/Thermostat RF Remote Handset
• Simultaneously press and hold the OFF and
(large flame)
buttons until a short acoustic signal confirms the start
sequence has begun; release buttons.
• Continuing signals confirm the ignition is in process.
• Once pilot ignition is confirmed, there is main gas flow.
• After the ignition the remote will go automatically into temperature control mode (CSA-versions) or manual mode
(CE-versions)
TO TURN OFF THE APPLIANCE
Press OFF button on remote handset.
NOTE:Press
(small flame) to turn main gas to pilot gas.
TO OPEN AND CLOSE SOLENOID VALVE/BURNER
NOTE: The latching solenoid valve will not operate for one minute after ignition.
The latching solenoid valve cannot operate
manually. If the battery runs down it will remain in the last
operating position. During normal operation the solenoid
valve will be reset into the ON position when the GV60 is
switched OFF remotely.
•
•
•
Upon ignition both Burner and Decorative Burner are ON.
Press upper left and lower right button simultaneously to
switch the Burner OFF (printed instructions are located on the
battery cover).
Press upper left and upper right button simultaneously
to switch the Burner ON. (Display and Timer/Thermostat
Remote Handsets: the AUX symbol on the display will
indicated that the solenoid valve is OPEN.)
ADJUSTMENT - FLAME HEIGHT
Standard, Display, Timer/Thermostat RF Remote Handsets
• In standby mode: Press
(large flame) to increase flame
height.
• Press
(small flame) to decrease flame height or to set
appliance at pilot flame.
• For fine adjustment tap the large/small flames.
SETTING °C/24 HOUR OR °F/12 HOUR CLOCK
Display, Timer/Thermostat RF Remote Handsets
• Press OFF and
(small flame) until display changes from
Fahrenheit/12 hour clock to Celsius/24 hour clock and vice
versa.
SETTING THE TIME
Display, Timer/Thermostat Remote Handsets
• This display will flash after either:
a. Installing the battery or
b. Simultaneously pressing the
(large flame) and
(small flame).
• Press (large flame) to set the hour and the (small flame)
to set the minute.
• Press OFF to return to manual mode or simply wait and it will
automatically return to the manual mode.
Remaining Instructions pertain to Timer/Thermostat RF
Remote Handset only
CHANGING THE MODE OF OPERATION
Briefly pressing the SET button changes the mode of operation in
the following order:
MAN
TEMP
TEMP TIMER
MAN
and back to
NOTE: MANUAL mode can also be reached by pressing either
the (large flame) or the (small flame).
MAN
•
•
•
Mode - Manual Flame Height Adjustment
Press
(large flame) to turn on the main burner.
Press
(large flame) to increase the flame height.
Press (small flame) to decrease the flame height or to go to
pilot standby position.
NOTE:While pressing either button a symbol indicating
transmission appears on the display. The receiver
confirms transmission with an acoustic signal.
TEMP
- Daytime Temperature Mode
(appliance must be in standby mode; pilot ignited):
The room temperature is measured and compared to the set
temperature. The flame height is then automatically adjusted to
achieve the Daytime set temperature.
- Nighttime Setback Temperature Mode
(appliance must be in standby mode; pilot ignited):
The room temperature is measured and compared to the Nighttime Setback temperature. The flame height is then automatically
adjusted to achieve the Nighttime Setback temperature.
TEMP
- Timer Mode
(appliance must be in standby mode; pilot ignited):
TIMER
The Timer setting allows you to set two (2) burner
every 24 hours.
TEMP
times
For TEMP to operate as a thermostat, TEMP must be set at 40°F
(4°C) or higher.
Page 18
28092-1-0911
G6R-P3TAN5 REMOTE CONTROL INSTRUCTIONS
If the TEMP setting is decreased to --, the motor will turn the valve
to the standby position in the moon times and await the next burner
TEMP
cycle.
NOTE: The display shows the set temperature every 30 seconds.
SETTING THE TEMPERATURE
•
•
•
•
TEMP
Select either the
MODE or the TEMP MODE by briefly
pressing the SET button.
Hold the SET button until the TEMP display flashes.
Set the desired temperature with (large flame) or (small
flame).
Press OFF or simply wait to complete programming.
SETTING THE TIMER
•
Select Timer mode by briefly pressing the SET button.
•
•
Press and hold the SET button until the P1
(sun symbol)
is displayed) and the time flashes. Set the hour by pressing
the
(large flame) and set the minutes by pressing the
(small flame).
Briefly press SET button for the next burner cycle time.
•
Example: P2
•
(sun symbol) and P2
(moon symbol).
Once all four (4) times are set, press OFF or simply wait to
complete programming.
(moon symbol) continue through P2
MANUAL OPERATION
(Only possible when MANUAL knob is used)
Follow appliance manufacturer’s instructions for gaining access to
the gas control and the pilot burner. Access to the pilot burner is
only required for ignition with a match.
When turning main valve knob, do not force. Knob has a slip clutch
that clicks until the end stops are reached. This allows for manual
flame height adjustment as well as adjustment to pilot standby position.
1. STOP! Read the safety information included before proceeding.
2. Turn main valve knob to the OFF, full clockwise
position.
3. Turn MANUAL knob to the MAN, full clockwise
position.
4. Place ON/OFF switch (if equipped) in O (OFF position).
5. Wait five (5) minutes to clear out any gas. Verify that no gas
is in the area around the appliance, including near the floor. If
you detect gas STOP! Follow “A” in the safety information on
page 20. If no gas is present, proceed to step 6.
6. Place ON/OFF switch (if equipped in (ON position).
7. With the MANUAL knob in MAN position a manual pilot valve
operator and piezo igniter (optional) are accessible.
28092-1-0911
8. Fully push down manual pilot valve operator and hold
in, to start pilot gas flow.
Ignition with match:
Immediately light the pilot with a match, while continuing to
hold in the manual pilot valve operator for about one (1) minute after the pilot is lit. Release manual pilot valve operator. If
pilot does not stay lit, wait five (5) minutes and repeat.
Ignition with piezo igniter:
Change the ignition cable from the receiver to the
valve. Use the push piezo igniter to ignite. If pilot does
not stay lit, wait five (5) minutes and repeat.
NOTE: If the pilot does not stay lit after several tries, turn the
gas control knob (main valve knob) to OFF and proceed to
step 11.
9. If applicable, per appliance manufacturer’s instructions,
replace pilot access panel before proceeding.
10.Turn MANUAL knob to the ON, full counterclockwise
position.
11. Turn main valve knob to the full ON, full counterclockwise
position.
12. If the appliance will not operate, follow the instructions “TURN
OFF GAS TO APPLIANCE” and call the service technician or
gas supplier.
TURN OFF GAS TO APPLIANCE
•
•
•
•
•
Press OFF button on remote or wall switch/touch pad/switch
panel.
Follow appliance manufacturer’s instructions for gaining
accessibility to the gas control.
Place ON/OFF switch (if equipped in O (off position).
Turn main valve knob to the OFF full
clockwise
position.
Replace appliance accessibility cover (if applicable), per
appliance manufacturer’s instructions.
MISCELLANEOUS
Low Battery Indication
Receiver:
three short beeps will sound when motor turns
Standard/Infrared remote:
the red LED will get darker
Remote with display:
“BATT” will appear on display
NOTE: Pertains to Thermostatic Display/Handsets: If the battery
of the handset is low or if the transmitter is out of the communication range, the motor turns down the valve to pilot
gas after 6 hours.
NOTE: With very low battery the GV60 system shuts off the fire
completely. This will not happen if the power supply is
interrupted.
Battery replacement
Battery replacement is recommended at the beginning of each
heating season. Pull ribbon to remove batteries. Do not use metal
tools to remove batteries. Using a metal tool could cause a short
that may damage the receiver.
Page 19
G6R-P3TAN5 REMOTE CONTROL INSTRUCTIONS
Location of Receiver
When the RF-receiver is placed in the appliance, the surrounding
metal can reduce reception considerably. The position of the antenna on the receiver also influences reception. It is recommended
to straighten the antenna. The antenna must not come in contact
or cross the ignition wire, this may render the receiver inoperable.
MAIN VALVE KNOB
MANUAL KNOB
PIEZO IGNITER
CONNECTION FOR
MANUAL IGNITION
NOTE: To keep receiver free from debris, dirt, and humidity, do
not remove the receiver from the plastic bag until all construction is complete.
Piezo Igniter
(optional)
COMBINATION CONTROL
Connection
Piezo Igniter
Tab 2.8 x 0.8 mm
ON/OFF SWITCH
ON/OFF Switch
(optional) in
ON Position
O
INTERRUPTER
BLOCK
MANUAL Knob
in MAN Position
I
THERMO CURRENT
CABLE #2 OR ON/OFF
SWITCH WITH SOLDERED CABLE
8 Wire
Receiver Jack
THERMO CURRENT
CABLE #1
THERMOCOUPLE
Manual Pilot
Valve Operator
IGNITION CABLE
RF ANTENNA
SPARK
SW
TC
MA
GR
MO
PANEL
SW
Microswitch
Main Valve Knob
in OFF Position
8 WIRE CABLE
BATTERY
COMPARTMENT
BUTTON “RESET”
Cutout for Pilot Gas Adjustment
Page 20
MANUAL Knob
in position for
automatic ignition
Wiring Diagram
Figure 14
28092-1-0911
VFSE-(18,24,30) LIGHTING INSTRUCTIONS
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by
hand. When lighting the pilot, follow these instructions
exactly.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the floor because some
gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch;
do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
1.
2.
3.
4.
•
If you cannot reach your gas supplier, call the fire
department.
C. Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or
turn by hand, don't try to repair it; call a qualified service
technician. Force or attempted repair may result in a fire
or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
LIGHTING INSTRUCTIONS
“I/O”
(ON/OFF)
SWITCH
MAN
NO
TO IGNITE PILOT
HANDSET MODE
MANUAL MODE
To Ignite Burner
PIEZO
IGNITER
O
75 F
MAN
STOP! Read the safety information above.
Open bottom louver assembly (if applicable).
Press the "I/O" (ON/OFF) button on the valve face to "OFF."
Wait five (5) minutes to clear out any gas, then smell for gas
including near the floor. If you smell gas, STOP! Follow "B"
in the safety information above. If you don't smell gas, go to
the next step.
LIGHTING PROCEDURE - HANDSET METHOD
1. Turn control arrow on valve face to "ON." Press the "I/O" button to "I." Press the "OFF" and "UP" buttons on the handset,
firmly at the same time. A long "Beep" will sound, followed by
5 short "beeps." Ignitor will spark and will continue until pilot
is lit. For full Remote Control operation see Appliance Installation manual.
LIGHTING PROCEDURE - MANUAL METHOD
1. Press the "I/O" (ON/OFF) button to "I."
2. Turn control arrow on valve face to "MAN."
3. Using a small bladed screwdriver, press and hold button
within hole on control. Manually depress piezo igniter button
to light pilot. If pilot does not light, steps 2 to 3 can be immediately repeated. If the pilot will not stay lit after several tries,
follow the instructions "To Turn Off Gas to Appliance" and call
your service technician or gas supplier.
4. When the pilot is lit and stable, turn flame height control knob
counterclockwise
and the main burner will ignite.
To adjust flame height, turn flame height control knob.
SET
OFF
Press firmly
at same time
PILOT
ELECTRODE
THERMOCOUPLE
(LPG)
THERMOCOUPLE
(NATURAL)
CORRECT PILOT FLAME
PRESS IN
& HOLD
PILOT
ELECTRODE
THERMOCOUPLE
(LPG)
THERMOCOUPLE
(NATURAL)
INCORRECT PILOT FLAME
TO TURN OFF GAS TO APPLIANCE
MANUAL MODE - To turn off main burner, tun flame height
control knob fully clockwise
. To fully shut down, press
"I/O" button to "O."
28092-1-0911
HANDSET MODE - Press "OFF" button on handset. To fully
shut down, press "I/O" button to "O."
Page 21
RCAF-1031-4 REMOTE CONTROL INSTRUCTIONS
NOTE: This remote is for use on VFSV Models ONLY.
INTRODUCTION
This remote control system was developed to a provide safe, reliable, user-friendly remote control system for gas heating appliances. The system can be operated manually from the transmitter.
•
It is suggested that the slide switch be placed in the
OFF position if you will be away from your home for an
extended period of time.
TRANSMITTER
The transmitter operates on a 12V (A23) battery that is included.
Install the 12V battery supplied with the unit into the battery compartment. It is recommended that ALKALINE batteries always be
used for this product. Be sure the batteries are installed with
the (+) and (-) ends facing the correct direction.
The LED signal light should illuminate when either the ON/OFF or
HI/LOW button is pressed. If the signal light does not illuminate,
check the position of the transmitter's battery, and if the battery is
fully charged.
WIRING INSTRUCTIONS
WARNING: DO NOT CONNECT REMOTE RECEIVER
DIRECTLY TO 110-120VAC POWER. THIS WILL BURN
OUT THE RECEIVER. FOLLOW INSTRUCTIONS FROM
MANUFACTURER OF GAS VALVE FOR CORRECT WIRING
PROCEDURES. IMPROPER INSTALLATION OF ELECTRIC
COMPONENTS CAN CAUSE DAMAGE TO GAS VALVE AND
REMOTE RECEIVER.
KEY SETTINGS
1. ON/OFF - This turns the appliance On
or Off.
2. H/L - This controls the height of the
flame. It has four levels: High, Medium
High, Medium Low and Low. The H/L
button will not turn the burner On or
Off.
IMPORTANT: THE REMOTE RECEIVER SHOULD BE POSITIONED WHERE AMBIENT TEMPERATURES DO NOT EXCEED 130°F.
CONNECT THE RECEIVER TO THE AF-1031 SERIES GAS
VALVE WITH THE STEP MOTOR
• Do not install the 4 AA batteries into the receiver until the DC
Step Motor is connected to the receiver. The receiver will calibrate the step motor once the batteries are installed.
• Connect the 4 pin female connector from the DC step motor
to the 4-pin male connector on the wire harness.
• Connect the 4 pin female connector on the wire harness to the
4-pin connector on the back of the receiver.
• Install the 4 AA batteries in to the receiver.
• After receiver is connected to the DC step motor using the
supplied wire harness, make sure to locate the receiver in an
area that will not exceed the 130°F. This location will always
be towards the front of the firebox.
RECEIVER
Install the 4 AA-size batteries supplied with the unit. It is recommended that ALKALINE batteries always be used for this product.
Be sure the batteries are installed with the (+) and (-) ends
facing the correct direction.
The remote receiver has a 2-position slide switch for selecting the
mode of operation, which is OFF/REMOTE
• REMOTE: The receiver must be in this position if you want
to use the appliance, you must use the transmitter to turn
on the appliance. If the system does not respond to the
transmitter on initial use, check the battery positions in the
remote. If that does not work, see the SECURITY CODE
section.
• OFF: Will disable the remote receiver.
Page 22
28092-1-0911
RCAF-1031-4 REMOTE CONTROL INSTRUCTIONS
THERMO-SAFETY FEATURE
When the ambient temperature inside the receiver case reaches
130°F, the RECEIVER will automatically send power to the step
motor on the valve to shut the fireplace system off and the RECEIVER will begin emitting a series of 4 "beeps" every 2 seconds.
When the ambient temperature at the RECEIVER drops between
120°F and 130°F, the user can reactivate the fireplace by pushing the ON/OFF button on the transmitter. When the ON/OFF button is pressed, the THERMISTOR "resets" itself and the fireplace
will begin operating again. However, the "beeping" will continue if
the ambient temperature remains between 120°F and 130°F. This
"beeping" alerts the user that the RECEIVER should be repositioned so the ambient temperature drops below 120°F. When the
temperature drops below 120°F, and the control is reset by pressing the ON/OFF button, the "beeping" will cease.
SECURITY CODES
This transmitter has one of 256 unique security codes. It may be
necessary to program the remote receiver to learn the security
code of the transmitter upon initial use, if batteries are replaced, or
if using a replacement transmitter.
NOTE: This receiver can hold up to 3 transmitter codes. This if for
the times when a second hand held transmitter or a wall transmitter is required.
• Make sure the receiver's slide switch is in the REMOTE position.
• Press and release the LEARN button on the receiver.
• When you hear the "beep", press and hold the ON/OFF or H/L
button for about 2 seconds on the transmitter.
• You will then hear a series of beeps that indicated that your
new transmitter has been accepted by the receiver.
• If you press the LEARN button on the receiver and you hear
no beeps, the receiver is unable to retain any more transmitter
codes (make sure that the transmitter and the receiver batteries are properly installed and fully charged.
• To delete all of the transmitter codes on your receiver, press
and hold the LEARN button for 10 seconds. Then you will
hear a series of beeps indicating that the receiver's memory
has been cleared.
TRANSMITTER WALL CLIP
The transmitter can be hung on a
wall using the clip provided.
• Wood - Drill 1/8" pilot holes and
install with screws provided.
• Plaster/Wallboard - Drill 1/4"
holes, tap plastic anchors in
with hammer then install with
the screws provided.
BATTERY LIFE
Life expectancy of the alkaline batteries in the transmitter and receiver should be at least 12 months. Check and replace all batteries:
• Annually.
• When operating range becomes reduced.
• When transmissions are not received by the remote receiver.
• If the remote receiver batteries measure less than 5.3 volts
(all four batteries in combination).
• If the hand held transmitter battery measures less than 9.0
volts.
TROUBLESHOOTING
If you encounter problems with your fireplace system, the problem
may be with either the fireplace itself or with the remote. Review
the fireplace manufacturer's operation manual to make sure all
connections are properly made. Then check the operation of the
remote in the following manner:
• Make sure all batteries are correctly installed in the transmitter
and receiver. Also check that the batteries are fully charged.
• Check batteries in transmitter to make sure contacts are
touching (+) and (-) ends of battery. Bend metal contacts in
for tighter fit.
• Be sure receiver and transmitter are within 20' - 25' operating
range.
• Keep receiver from temperatures exceeding 130°F. Battery
life will be shortened if exposed to high temperatures.
• If receiver is installed in a tightly enclosed metal surrounding,
the operating distance will be shortened.
• Make sure the hand-held transmitter and remote receiver are
communicating properly (see SECURITY CODES section).
FCC REQUIREMENTS
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR
ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THE EQUIPMENT. SUCH
MODIFICATIONS COULD VOID THE USER'S AUTHORITY
TO OPERATE THE EQUIPMENT.
28092-1-0911
Page 23
VFSV-(16,18,24,30) LIGHTING INSTRUCTIONS
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion may result
causing property damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by
hand. When lighting the pilot, follow these instructions
exactly.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the floor because some
gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch;
do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire
department.
C. Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or
turn by hand, don't try to repair it; call a qualified service
technician. Force or attempted repair may result in a fire
or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information on this page.
2. Push in gas control knob slightly and turn clockwise
to "OFF." Do not force.
3. Turn gas flow adjustment
PIEZO
IGNITOR
knob
clockwise
either manually or with remote
control to "OFF."
GAS CONTROL KNOB
SHOWN IN "PILOT!
4. Wait ten (10) minutes to clear POSITION.
out any gas. Then smell for
gas, including near floor. If you
smell gas, STOP! Follow "B" in
the safety information above. If
you do not smell gas, go to the
next step.
5. Find pilot - follow metal tube
from gas control. The pilot is
behind the second log on the
right side.
6. Turn gas control knob counterclockwise
to "PILOT."
7. Push in control knob all the way and hold in. Immediately
light the pilot with the piezo pilot ignitor or use a match. Continue to hold the control knob in for about one (1) minute after
the pilot is lit. Release knob, and it will pop back up. Pilot
should remain lit. If it goes out, repeat steps 5 through 8.
If knob does not pop up when released, stop and immediately call a qualified service technician or gas supplier.
If the pilot will not stay lit after several tries, turn the gas
control knob to "OFF" and call your service technician or gas
supplier.
8. Turn gas control knob counterclockwise
to off.
9. Turn on all electric power to the appliance (if applicable).
10. Set thermostat to desired setting.
TO TURN OFF GAS TO APPLIANCE
1. Turn gas flow adjustment knob clockwise
manually or with remote control to “OFF”.
Page 24
either
2. Push in gas control knob slightly and turn clockwise
to “OFF”. Do not force.
28092-1-0911
PILOT FLAME CHARACTERISTICS
Figure 15 shows a correct pilot flame pattern. The correct flame will
be blue and will extend beyond the thermocouple. The flame will
surround the thermocouple just below the tip. A slight yellow flame
may occur where the pilot flame and main burner flame meet. Figure
16 shows an incorrect pilot flame pattern. The incorrect pilot flame
is not touching the thermocouple. This will cause the thermocouple
to cool. When the thermocouple cools, the heater will shut down.
Cleaning and Maintenance/Pilot
VFSV, VFSE PILOT
Cleaning and Maintenance/Pilot
Oxygen Depletion Sensor Pilot (Figure 17)
When the pilot has a large yellow tip flame, clean the Oxygen
Depletion Sensor as follows:
1. Clean the ODS pilot by loosening nut B from the pilot tubing.
When this procedure is required, grasp nut A with an open end
wrench.
2. Blow air pressure through the holes indicated by the arrows.
This will blow out foreign materials such as dust, lint and spider
webs. Tighten nut B also by grasping nut A.
Warning: Never use needles, wires, or similar cylindrical
objects to clean the pilot to avoid damaging the calibrated
ruby that controls the gas flow.
Figure 17
Correct Pilot Flame Pattern
Figure 15
Incorrect Pilot Flame Pattern
Figure 16
If pilot flame pattern is incorrect, as shown in Figure 16
• See Troubleshooting, page 27.
28092-1-0911
Page 25
CLEANING AND SERVICING
Annual inspection and cleaning by your dealer or qualified
service technician is recommended to prevent malfunction
and/or sooting.
TURN OFF HEATER AND ALLOW TO COOL BEFORE
CLEANING.
Remove logs, handling carefully by holding gently at each end.
Gloves are recommended to prevent skin irritation from ceramic
fibers. If skin becomes irritated, wash gently with soap and water.
Refer to manual for correct log placement.
PERIODIC CLEANING – Refer to parts diagram for location of
items discussed below.
• Do not use cleaning fluid to clean logs or any part of heater.
• Logs - brush with soft bristle brush or vacuum with brush
attachment.
• Remove loose particles and dust from the burner areas,
controls, piezo covers and grate. Don’t remove media from
inside burner box.
• Inspect and clean burner air intake hole. Remove lint or particles
with brush. Failure to keep air intake hole clean will result in
sooting and poor combustion.
ANNUAL CLEANING/INSPECTION – Refer to parts diagram for
location of items discussed below.
•
•
•
•
•
•
Inspect and clean burner air intake hole. Remove lint or particles
with vacuum or brush. Failure to keep air intake hole clean will
result in sooting and poor combustion.
Inspect and clean all burner ports.
Inspect ODS pilot for operation and accumulation of lint at air
intake holes.
Verify flame pattern and log placement for proper operation.
Verify smooth and responsive ignition of main burner.
Check level of ceramic media in burner. Burner should be full,
up to the level of openings in burner top.
VFSV
Note: (Wiring harness located in envelope)
Connect black/red 3/16" terminal wire from receiver to 3/16" terminal
on valve. Connect black 1/4" terminal wire from receiver to 1/4"
terminal on valve. Install remote receiver cover over receiver when
receiver is installed into fireplace area. Locate receiver and cover to
the right and forward of valve. (Do not put receiver behind logs).
WIRING
MAIN VALVE KNOB
MANUAL KNOB
PIEZO IGNITER
CONNECTION FOR
MANUAL IGNITION
COMBINATION CONTROL
ON/OFF SWITCH
O
INTERRUPTER
BLOCK
I
THERMO CURRENT
CABLE #2 OR ON/OFF
SWITCH WITH SOLDERED CABLE
THERMO CURRENT
CABLE #1
THERMOCOUPLE
IGNITION CABLE
SPARK
THERMOCOUPLE
(LPG)
THERMOCOUPLE
(NATURAL)
RF ANTENNA
SW
TC
MA
GR
MO
ADJ.
LEARN
PANEL
SW
8 WIRE CABLE
OFF
REMOTE
BATTERY
COMPARTMENT
BUTTON “RESET”
VFSE Wiring Diagram
Page 26
Figure 18
VFSV Wiring Diagram
28092-1-0911
TROUBLESHOOTING
SYMPTOMS - POSSIBLE CAUSES AND CORRECTION
1. When ignitor button is pressed, there is no spark at ODS/
pilot.
a. Ignitor electrode positioned wrong - Replace pilot.
b. Ignitor electrode is broken - Replace pilot.
c. Ignitor electrode not connected to ignitor cable - Reconnect
ignitor cable.
d. Ignitor cable pinched or wet. Keep ignitor cable dry - Free
ignitor cable if pinched by any metal or tubing.
e. Broken ignitor cable - Replace ignitor cable.
f. Bad piezo ignitor - Replace piezo ignitor.
2. Appliance produces unwanted odors.
a. Appliance burning vapors from paint, hair spray, glues, etc.
- Ventilate room. Stop using odor causing products while
heater is running.
b. Gas leak - Locate and correct all leaks.
3. Appliance shuts off during use. (Pilot and main burner are
off.)
a. Not enough fresh air is available for ODS/pilot to operate Open window and/or door for ventilation.
b. Low line pressure - Contact local gas company.
c. ODS/pilot is partially clogged - Clean ODS/pilot.
d. Defective thermocouple - Replace pilot.
4. Appliance shuts off during use. (Pilot stays on.)
a. Low line pressure - Check line pressure to the valve.
5. Gas odor even when control knob is in OFF position.
a. Gas leak - Locate and correct all leaks.
b. Control valve defective - Replace control valve.
6. When ignitor button is pressed, there is spark at ODS/pilot,
but no ignition.
a. Gas supply turned off or manual shutoff valve closed - Turn
on gas supply or open manual shutoff valve.
b. Control knob not in PILOT position - Turn control knob to
PILOT position.
c. Control knob not pressed in while in PILOT position - Press
in control knob while in PILOT position.
d. Air in gas lines when installed - Continue holding down control
knob. Repeat igniting operation until air is removed.
e. ODS/pilot is clogged - Replace ODS/pilot assembly or get
it serviced.
g. Gas regulator setting is not correct - Replace gas
regulator.
7. ODS/pilot lights but flame goes out when control knob is
released.
a. Control knob not fully pressed in - Press in control knob
fully.
b. Control knob not pressed in long enough - After ODS/pilot
lights, keep control knob pressed in 30 seconds.
8.
9.
10.
11.
12.
c. Manual Shutoff valve not fully open - Fully open manual
shutoff valve.
d. Thermocouple connection loose at control valve - Hand
tighten until snug, then tighten 1/4 turn more.
e. Pilot flame not touching thermocouple, which allows
thermocouple to cool, causing pilot flame to go out. This
problem could be caused by either low gas pressure or dirty or
partially clogged ODS/pilot - Contact local gas company.
f. Thermocouple damaged - Replace thermocouple.
h. Control valve damaged - Replace control valve.
Burner does not light after ODS/pilot is lit.
a. Burner orifice clogged - Clean burner or replace main burner
orifice.
b. Burner orifice diameter is too small - Replace burner
orifice.
c. Inlet gas pressure is too low - Contact qualified service
person.
If burning at main burner orifice occurs (a loud, roaring
blow torch noise).
a. You must turn off burner assembly and contact a qualified
service person.
b. Manifold pressure is too low - Contact local gas company.
c. Burner orifice clogged - Clean burner or replace burner
orifice.
Logs appear to smoke after initial operation.
a. Vapors from paint or curing process of logs - Problem will
stop after a few hours of operation. Run the heater with the
damper open if you have one, or open a window for the first
few hours.
Log heater is intended to be smokeless. Turn OFF heater
and call qualified service person.
Heater produces a whistling noise when main burner is
lit.
a. Turning control knob to HIGH position when main burner is
cold - Turn control knob to LOW position and let warm up
for a minute.
b. Air in gas line - Operate burner until air is removed from
line. Have gas line checked by local gas company.
c. Dirty or partially clogged burner orifice - Clean burner or
replace burner orifice.
No gas to pilot.
a. LP-regulator shut down due to inlet pressure too high Verify LP tank regulator is installed and set at 11" to 13"
w.c. Replace regulator on heater.
If the gas quality is bad, your pilot may not stay lit, the burners may produce soot and the heater may backfire when lit. If the
gas quality or pressure is low, contact your local gas supplier immediately.
28092-1-0911
Page 27
PARTS LIST
Attention: When ordering parts, it is very important that part number and description of part coincide.
INDEX
NO.
PART
NO.
DESCRIPTION
1
15425
REAR LOG SUPPORT (16" MODELS)
1
15426
REAR LOG SUPPORT (18" MODELS)
1
15427
REAR LOG SUPPORT (24" MODELS)
1
15428
REAR LOG SUPPORT (30" MODELS)
2
11376
BURNER SUPPORT - LEFT
3
P200
ORIFICE FITTING
5
R5675
AIR SHUTTER - LP
5
R5676
AIR SHUTTER - NAT
6
R5170
PILOT, LP
6
R5171
PILOT, NAT
7
11833
PILOT SHIELD (NAT ONLY)
9
12437
9
INDEX
NO.
PART
NO.
DESCRIPTION
VFSE (CONTINUED)
COMMON
NS
11335
TUBING ASSEMBLY LP VALVE TO PILOT
NS
R10559 BATTERY, 9-VOLT
NS
R10518 FASTENER, HOOK
NS
R10519 FASTENER, LOOP
NS
R10573 3/8" NPT, HEX PLUG
NS
R10568 IGNITER WIRE, MAXITROL
NS
R10564 REMOTE CONTROL KIT
NS
R10565 REMOTE CONTROL THERMOSTAT
NS
R10569 SWITCH AND WIRE ASSEMBLY
NS
R10570 WIRE ASSEMBLY, THERMOCOUPLE
BURNER ASSEMBLY
(16" NAT MODELS)
NS
R10567 WIRE HARNESS (8 PIN)
12348
BURNER ASSEMBLY
(16" LP MODELS)
4
P308
ORIFICE - LP 16"
9
14033
BURNER ASSEMBLY (18" MODELS)
4
P210
ORIFICE - LP 18"
9
14035
BURNER ASSEMBLY (24" MODELS)
4
P304
ORIFICE - LP 24"
9
14037
BURNER ASSEMBLY (30" MODELS)
4
P265
ORIFICE - LP 30"
NS
12389
CERAMIC MEDIA
4
P286
ORIFICE - NAT 16"
NS
R2809
DAMPER CLAMP
4
P243
ORIFICE - NAT 18"
NS
11788
DECORATIVE ROCK
4
P211
ORIFICE - NAT 24"
NS
15998
ROCKWOOL (16" MODELS)
4
P209
ORIFICE - NAT 30"
NS
15999
ROCKWOOL (18" MODELS)
10
26321
BURNER SUPPORT RIGHT
(16" MODELS)
NS
15970
ROCKWOOL (24" & 30" MODELS)
26291
NS
11291
TUBING ASSEMBLY VALVE TO BURNER
10
BURNER SUPPORT RIGHT
(18",24",& 30" MODELS)
VFSE
VFSV
14
R10613 VALVE, AF1110
15
R9761
PIEZO IGNITOR
27017
IGNITER BRACKET
4
P250
ORIFICE - LP 18"
16
4
P245
ORIFICE - LP 24"
17
R10617 45° STREET ELBOW
4
P265
ORIFICE - LP 30"
18
R10618 REGULATOR, 4.0 W.C.
4
P243
ORIFICE - NAT 18"
18
R10689 REGULATOR, 10.0 W.C.
4
P244
ORIFICE - NAT 24"
19
27016
VALVE BRACKET
4
P211
ORIFICE - NAT 30"
8
R7063
PILOT REGULATOR
NS
27018
PILOT TUBE - VALVE TO PILOT
(NAT & LP)
10
11308
BURNER SUPPORT RIGHT WITH VALVE BRACKET
NS
R10619
REMOTE RECEIVER AND
TRANSMITTER, NAT
NS
R10620
REMOTE RECEIVER AND
TRANSMITTER, LP
NS
R2789
WIRE, IGNITER, 12"
NS
R8898
NIPPLE, 3/8 X 3/8 X 1 BLACK IRON
11
R10562 VALVE, MAXITROL (NAT)
11
R10563 VALVE, MAXITROL (LP)
12
R10566 ELECTRONIC CONTROL
13
R10572 CONNECTOR, THERMOCOUPLE
NS
14040
TUBING ASSEMBLY NAT VALVE TO REGULATOR
NS
14041
TUBING ASSEMBLY NAT REGULATOR TO PILOT
NS - Not Shown
USE ONLY MANUFACTURER'S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH.
Page 28
28092-1-0911
PARTS VIEW
“VFSV” MODELS
15
16
18
17
14
19
“VFSE” MODELS
13
12
11
28092-1-0911
Page 29
MASTER PARTS DISTRIBUTOR LIST
To Order Parts Under Warranty, please contact your local Empire dealer. See the dealer locator at www.empirecomfort.
com. To provide warranty service, your dealer will need your name and address, purchase date and serial number, and the
nature of the problem with the unit.
To Order Parts After the Warranty Period, please contact your dealer or one of the Master Parts Distributors listed below.
This list changes from time to time. For the current list, please click on the Master Parts button at www.empirecomfort.com.
Please note: Master Parts Distributors are independent businesses that stock the most commonly ordered Original Equipment repair parts for Heaters, Grills, and Fireplaces manufactured by Empire Comfort Systems Inc.
Dey Distributing
1401 Willow Lake Boulevard
Vadnais Heights, MN 55101
East Coast Energy Products
10 East Route 36
West Long Branch, NJ 07764
Phone: 651-490-9191
Toll Free: 800-397-1339
Website: www.deydistributing.com
Parts: Heater & Hearth
Phone: 732-870-8809
Toll Free: 800-755-8809
Fax: 732-870-8811
Website: www.eastcoastenergy.com
Parts: Heater & Hearth and Grills
Victor Division of F. W. Webb Company
200 Locust Street
Hartford, CT 06114
Phone: 860-722-2433
Toll Free: 800-243-9360
Fax: 860-293-0479
Toll Free Fax: 800-274-2004
Websites: www.fwwebb.com & www.victormfg.com
Parts: Heater & Hearth and Grills
HOW TO ORDER REPAIR PARTS
Parts Not Under Warranty
Parts can be ordered through your Service Person, Dealer, or a Master Parts Distributor. See this page for the Master Parts Distributors list. For best results, the service person or dealer should order parts through the distributor. Parts can be shipped directly to the
service person/dealer.
Warranty Parts
Warranty parts will need a proof of purchase and can be ordered by your Service Person or Dealer. Proof of purchase is required for
warranty parts.
All parts listed in the Parts List have a Part Number. When ordering parts, first obtain the Model Number and Serial Number from the
name plate on your equipment. Then determine the Part Number (not the Index Number) and the Description of each part from the following illustration and part list. Be sure to give all this information . . .
Appliance Model Number
Appliance Serial Number
Part Description
Part Number
Type of Gas (Propane or Natural)
Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store.
Shipments contingent upon strikes, fires and all causes beyond our control.
Page 30
28092-1-0911
APPLIANCE SERVICE HISTORY
Date
Dealer Name
28092-1-0911
Service Technician Name
Service Performed/Notes
Page 31
EMPIRE
Comfort Systems
Empire Comfort Systems Inc.
918 Freeburg Ave. Belleville, IL 62220
If you have a general question about our products, please e-mail us at
info@empirecomfort.com.
If you have a service or repair question, please contact your dealer.
www.empirecomfort.com
Page 32
28092-1-0911
Download PDF