Yamaha | DME4io-ES | DME8i-ES DME8o-ES DME4io-ES

DME8i-ES, DME8o-ES, and DME4io-ES
Audio I/O Distribution and DSP Expansion Units
DME8i-ES
DME8o-ES
DME4io-ES
1U
DME8i-ES Rear Panel
Extensive I/O and processing expansion for DME64N/DME24N systems and
EtherSound™ networks.
• Vastly expand the capabilities and capacity of a DME-based sound system, or any other networked audio devices that
use EtherSound™ protocol.
• Controllable remote I/O plus powerful DSP processing capability allow distributed processing for unprecedented
system design flexibility and power.
• Reduce system cabling costs while maximizing overall reliability.
• Also usable as stand-alone processors in smaller systems.
• Full 24-bit 96-kHz audio processing, plus the same highly-acclaimed analog circuitry used in the DME24N.
• Supplied DME Designer software application can be used to control, monitor, and create complete processing
“configurations” in the same way as with the DME64N or DME24N.
• 8-in/4-out GPI terminals allows direct, easy connection to wall-mountable CP4SF control panels featuring four switches
and four faders.
OPTIONS
REMOTE CONTROL PANELS
ICP1 Intelligent Control Panel
The most sophisticated of the DME
series remotes, the ICP1 connects
via Ethernet. Functions include
scene recall and six user-defined
keys at the top and bottom of the LCD screen, which can be
assigned to DME parameters such as microphone and
music source levels. Up to 4 sets of "pages" are available giving up to 24 parameters. LCD display shows names and
scenes and function keys in five languages - English,
German, French, Spanish and Japanese.
CP4SF
CP4SW
CP1SF
Wall-mountable remote control panel for
GPI control. Uses a standard (US-type)
3 gang wall box.
Wall-mountable remote
control panel for GPI control.
Uses a standard (US-type)
1 gang wall box.
Wall-mountable remote
control panel for GPI control.
Uses a standard (US-type)
1 gang wall box.
Four switches
and four
faders control
panel
Four switches
control panel
One switch and
one fader
control panel
DME8i-ES, DME8o-ES, and DME4io-ES
GENERAL SPECIFICATIONS
Model
Frequency response
Total harmonic distortion
Hum & noise
Dynamic range
Crosstalk
Power consumption
Dimensions (W x H x D)
DME8i-ES
0, -1.5, +0.5; 20-20kHz@48kHz fs, 20-40kHz@96kHz fs
Weight
4.4kg (9.7lbs)
DME8o-ES
DME4io-ES
Less than 0.05%; +4dBu, GAIN=10dB
-128dBu (EIN)
106dB
Less than -80dB
40W
480 x 44 x 361mm (18.9" x 1.7" x 14.2"), 1U
*1. DME8i EIN is measured with DME8o for output conversion
*2. Total Harmonic Distortion is measured with a 18dB/octave filter @80kHz.
*3. Hum & Noise and dynamic range are measured with a 6dB/octave filter @12.7kHz; equivalent to a 20kHz filter with infinite dB/octave attenuation.
*4. Crosstalk is measured with a 18dB/octave filter @80kHz
ANALOG INPUT SPECIFICATIONS
Input termials
CH INPUT
Gain
-60dB
Actual Load For Use With
Impedance
Nominal
3kΩ
+10dB
50-600Ω
Mics &
600Ω Lines
CONTROL I/O SPECIFICATIONS
Input Terminals
Terminals
Nominal
Max.
before Clip
-60dBu
-40dBu
+10dBu
+30dBu
EtherSound
Terminals
ANALOG OUTPUT SPECIFICATIONS
CH OUTPUT
Impedance
75Ω
For Use With
Nominal
600Ω
EtherSound
Latency
Level
Calculable: 125μ
sec (SSI OUT
to SSI IN)
Output Level
Max.
before Clip
Nominal
+4dBu
+24dBu
Connectors
Euroblock*
*1. All DA converters are 24-bit linear, 128-times oversampling (Fs=48kHz)/64-times oversampling (Fs=96kHz).
DIMENSIONS
Level
Ethernet
IEEE802.3
10BaseT/100Base-TX
RJ-45
USB
USB1.1
-
Type B
REMOTE
RS232C/RS422
RS232C/RS422
D-sub 9pin (male)
GPI *
*1. Inputs: 8 channels, Outputs: 4 channels
Inputs: Not apply 2 wire Fader mode
Outputs: Imax/pin = 16mA
Outputs: VH = 2.5V(min.), VL = 0.6V(max.)
COMPONENT LIST
Category
Delay
Dynamics
Component
Long, Short
Gate, Ducking, Expander, Compander,
Filter
EQ
Compressor, De-Esser, Limiter
BPF, HPF, LPF, Notch
PEQ, GEQ
Fader
Pan
LR, LCR, 3-1, 5.1, 6.1
Meter
Simple Mixer
Auto Mixer (II)
Matrix Mixer
3
1
44
Rubber feet
are included in
the package.
Connector
Euroblock
(3.5mm Pitch)
354
361
Format
0-5V
TTL
5V
Mixers
480
RJ-45 x2 (In/Out)
-
IN
OUT
+V
1
(4)
unit : mm
440
100Base-TX
Connector
Euroblock*
*1. All AD converters are 24-bit linear, 128-times oversampling (Fs=48kHz)/64-times oversampling (Fs=96kHz).
*2. +48V DC (Phantom power) is supplied to CH INPUT EUROBLOCK connectors via each individual software
controlled switch.
Output terminals
Format
Connectors
I/O functions
Source
Routing functions
Crossover
Speaker Processor
Other functions
Delay Matrix
Analog I/O
CobraNet I/O (16IN/16OUT)
Oscillator
Wav File Player
Router
Crossover
Crossover processor (II)
Speaker processor
Room Combiner
Ambient Noise Compensator
Audio Detector
Auto Gain Control
Event Scheduler
Program Ducker
Download PDF