Vermont Castings | UVL30RP | Operating instructions | Vermont Castings UVL30RP Operating instructions

Installation and Operation
Instructions for
Vent-Free Gas Log Sets*
Models UVL18RN, UVL18MN,
UVL24RN, UVL24MN, UVL30RN,
UVL30MN (Natural Gas)
Models UVL18RP, UVL18MP, UVL24RP,
UVL24MP, UVL30RP, UVL30MP
(Propane)
WARNING
If the information in this manual is not followed exactly, a fire or explosion may result,
causing property damage, injury, or loss of life.
— Do not store or use gasoline or other
flammable vapors and liquids in the vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do
not use any phone in your building.
ATTENTION
Installation and service must be performed by a qualified agency, individual,
firm, corporation, or company, experienced in the installation, repair, and
servicing of this type of gas appliance. Do
not modify, alter or tamper with any part
of this heater, control, or logs.
• Immediately call your gas supplier from
a neighbor’s phone. Follow the gas
supplier’s instructions.
• If you cannot reach your gas supplier,
call the fire department.
INSTALLER PLEASE NOTE:
DO NOT begin installation of this gas
logset until all instructions have been
read and understood.
This appliance may be installed in an
aftermarket, permanently located, manufactured (mobile) home, where not prohibited by local codes.
This appliance is only for use with the
type of gas indicated on the rating plate.
This appliance is not convertible for use
with other gases.
WARNING
CARBON MONOXIDE POISONING MAY LEAD TO DEATH.
When used without fresh air, vent-free log sets may give off carbon monoxide, an odorless, poisonous gas.
Some people - pregnant women, people with heart or lung disease, anemia, or persons under the influence of
alcohol, and persons at high altitudes are more affected by carbon monoxide than others.
Early signs of carbon monoxide poisoning resemble the flu - headache, dizziness, and/or nausea. If you have these
signs, the heater may not be installed or working properly. GET FRESH AIR AT ONCE! Have the heater serviced
before using it again.
*These logsets are not for exterior use.
DE S I GN
CE
RTIFI E D
Tested and listed to ANSI Z21.11.2a-2003,
Unvented Heaters, and Z21.60a-2003; CSA 2.26a-2003
Decorative Gas Appliances for Installation in
Solid-Fuel Burning Fireplaces.
C E RT I F I E D
SAVE THIS MANUAL FOR FUTURE REFERENCE.
7412957 10/04 Rev. 11
General Information
In order to assure a safe and effective installation, only a qualified service person who is
familiar with the building codes and installation
techniques appropriate to your area may install
and service this appliance.
The Logsets have been designed and tested to operate
safely when installed according to the installation
instructions contained in this manual. Read all instructions
before starting the installation.
• The vent-free gas logset must be installed only in a
fireplace constructed of noncombustible material.
• These logsets are not for exterior use.
• This appliance is for supplemental heating only. It should
not be used as the primary heat source for a dwelling.
• The logset should be inspected before use and at least
annually thereafter. More frequent cleaning may be
necessary due to excessive lint from carpeting or bedding
material.
• In the United States, the installation and operation must
conform to local codes or, in the absence of local codes,
with the National Fuel Gas Code, ANSI Z223.1/NFPA 54,
latest edition, CSA-B149.1 Installation Code, and with the
National Electrical Code, ANSI/NFPA70 (latest edition).
State or local codes may only allow operation of this
appliance in a vented configuratio. Check your state or
local codes. In Canada, check local province for proper
use or CSA-B149. Refer to pages 7 and 8 for installation
details.
• The gas logset and its individual shutoff valve must be
disconnected from the gas supply piping system during
any pressure testing of that system at test pressures in
excess of 1/2 p.s.i.g. (3.5 kPa.) The gas logset must be
isolated from the gas supply piping system by closing its
individual manual shutoff valve during any pressure
testing of the gas supply piping system at test pressures
equal to or less than 1/2 p.s.i.g. (3.5 kPa.)
• Do not, under any circumstances, burn solid fuel (wood,
paper, coal) in the fireplace where you have installed your
logset. Do not use it for cooking. Put nothing on top of the
logs.
• The logset must be compatible with its fuel. Natural gas
requires different hardware than propane. Never attempt
to use natural gas with a propane logset or vice versa.
• For a propane burning logset, the supply tank must
include a high to low gas pressure regulator. The tank
must be outdoors. Do not, under any circumstances,
locate supply tanks inside any structure.
• The fireplace must include a screen made of chain
mesh or a similar material. You must keep the screen
closed at all times during the operation of the logset; it will
protect you in the event of an explosion.
• WARNING: If the fireplace contains glass doors, they
must remain open at all times during the operation of the
logset, allowing combustion air to circulate.
• In order to avoid any possible gas leaks, apply pipe joint
compound to all non-flared, threaded connections involved
in this installation. For propane, the joint compound must
be resistant to the corrosive action of propane.
• To check for leaks, always use a soapy water solution or
a sniffer. Never test by using an open flame.
• The area around the gas logset must be free of all
22
combustible materials, especially gasoline or other highly
flammable, vapor producing liquids.
• Due to high temperatures, locate this logset away from
both high traffic areas and furniture and draperies.
• Children and adults alike should be aware of the high
surface temperatures; to avoid the risk of burns or ignition
of clothing they should stay away.
• Do not touch any part of the logset other than the
controls while it is operating or immediately after you turn
it off.
• Supervise young children and pets carefully when they
are in the room where the logset is operating.
• Do not place clothing or other flammable material on or
near the logset.
• Make sure that any safety screen or guard, removed
during servicing, has been replaced before you use the
logset.
• Do not, under any circumstances, install the logset in
any bedroom, bathroom, other small, enclosed room,
mobile home or recreational vehicle.
• Do not install the logset in a drafty area or use it with any
after-market blower system that may cause drafting and
consequently alter the flame pattern.
• It is imperative that you keep clear all burner areas,
control compartments and passageways for circulating air.
• Do not move the logset in any way that might dislodge
the logs from their fixed positions. If you bump the logset
check to see if you have dislodged anything.
• Provide adequate clearances around air openings into
the combustion chamber and adequate accessibility
clearance for servicing and proper operation. NEVER
obstruct the front opening of the fireplace.
• Avoid propane tank dropping below 25% full. This will
help keep soot from occurring.
WARNING
This appliance is for installation in a solid-fuel
burning masonry fireplace with a working
flue, a U.L.-127 Listed manufactured solid-fuel
burning fireplace, in any CFM Specialty Home
Products ventless firebox or in any listed
ventless firebox enclosure certified to I.A.S.
U.S. requirements 2-97.
NOTICE
This is an unvented gas-fired heater. It uses air
(oxygen) from the room in which it is installed.
Provisions for adequate combustion and ventilation
air must be provided. Refer to pages 5 and 6.
This appliance operates as an unvented domestic
room heater when fitted to a masonry or factory-built
wood-burning fireplace with the flue damper closed,
or as a decorative appliance when the flue damper is
fully open. It must not be used for any other purpose
and must be fitted in a masonry or factory-built
fireplace or ventless firebox enclosure.
UVL Series
Installation Requirements
The fireplace must meet the minimum dimensions listed below. (Fig. 1) Do not install the logset if the
fireplace does not meet these minimums.
Min. Fireplace Dimensions
Logset
Gas
18” UVL18RN
A
Front
Width
B
Rear
Width
C
Overall
Depth
D
Overall
Height
20¹⁄₂”
17”
13¹⁄₂”
18”
Inlet Supply
Pressure (w.c.)
Min. Max.
5.5”
14.0”
Manifold
Pressure
Min. Input
BTU/hr
Max. Input
BTU/hr
17,000
24,000
15,000
24,000
24,500
35,000
18,000
35,000
25,000
39,000
28,500
39,000
11.0”
18,000
24,000
10.0”
17,000
24,000
11.0”
26,000
35,000
10.0”
18,000
35,000
11.0”
29,500
39,000
10.0”
29,000
39,000
3.5”
18” UVL18MN
24” UVL24RN
Natural
20¹⁄₂”
18¹⁄₂”
13¹⁄₂”
18”
5.5”
14.0”
3.5”
24” UVL24MN
30” UVL30RN
25¹⁄₂”
23”
13¹⁄₂”
18”
5.5”
14.0”
3.5”
30” UVL30MN
18” UVL18RP
20¹⁄₂”
17”
13¹⁄₂”
18”
11.0”
14.0”
18” UVL18MP
24” UVL24RP
Propane
20¹⁄₂”
18¹⁄₂”
13¹⁄₂”
18”
11.0”
14.0”
24” UVL24MP
30” UVL30RP
25¹⁄₂”
23”
13¹⁄₂”
30” UVL30MP
18”
11.0”
14.0”
occasionally be produced during heater operation
when impurities exist in the immediate area.
Cleaning solutions, paint, solvents, cigarette smoke,
candles, adhesives, new carpet or textiles, etc., all
can create fumes. These fumes may mix with
combustion air and can create odor. Such odors will
disappear over time, however, the condition can be
alleviated by opening a window or otherwise
providing additional ventilation to the area.
D
B
C
High Elevations
A
A. Front Width
C. Depth
B. Rear Width
D. Height
FD370-2
Fig. 1 Minimum fireplace dimensions.
Pressure Test Points
UVL-R Series: The gas control is equipped with a
captured screw-type pressure test point, therefore it
is not necessary to provide a 1/8" test point
upstream of the control.
UVL-M Series: The gas valve control is equipped
with a captured screw type inlet and manifold
pressure test point on the right side of the valve.
Odor During Operation
Neither natural gas nor propane gas give off an odor
when burned. The nature of a vent free combustion
system, however, is such that odors may
UVL Series
Input ratings are shown in BTU per hour and
are certified without deration from elevations
up to 4,500 feet (1,370m) above sea level.
Nuisance outages may occur at altitudes above
4,500 feet (1,370m) if dirt, dust, lint and/or
cobwebs are allowed to accumulate on burner
and/or ODS pilot. Monthly inspection and
cleaning is recommended for altitudes above
4,500 feet (1,370m)
For elevations above 4,500 feet (1,370m) in
USA, installations must be in accordance with
the current ANSI Z223.1/NFPA 54 and/or local
codes having jurisdiction.
In Canada, please consult provincial and/or
local authorities having jurisdiction for
installations at elevations above 4,500 feet
(1,370m)
3
Planning
Planning the installation is an important first step. It will
save time and money later in the actual installation. In
planning the installation, consider:
•
•
•
Where the heater will be located.
All components needed to complete the installation.
DO NOT use this heater in sleeping quarters, mobile
homes, or in recreational vehicles.
• Installation and repair should be done by a qualified
service person.
• DO NOT use this heater if any part has been under
water. Immediately call a qualified technician to inspect
the appliance and replace any part of the control system
and any gas control which has been under water.
• When used as an unvented heater, always ensure there
is adequate ventilation from the room where the appliance
is operating. This appliance is equipped with an ODS
(oxygen depletion sensor) pilot light safety system
designed to shut off the appliance if enough fresh air is
not available.
THIS APPLIANCE MUST NOT BE USED WITH GLASS
DOORS IN A CLOSED POSITION .
Keep the burner and control compartment clean. See
installation and operating instructions supplied with the
heater.
WARNING: During manufacturing, fabricating and
shipping, various components of this appliance are
treated with certain oils, films or bonding agents.
These chemicals are not harmful, but may produce
annoying smoke and smells as they are burned off
during the initial operation of the appliance, possibly
causing headaches or eye or lung irritation. This is a
normal and temporary occurrence. The initial break-in
operation should last 2-3 hours with the burner at its
highest setting. Provide maximum ventilation by
opening windows, doors and the chimney flue to
allow odors to dissipate. Any odors remaining after
this initial break-in will be slight and will disappear
with continued use.
This appliance operates as an unvented domestic room
heater when fitted to a masonry or factory-built woodburning fireplace with the flue damper closed, or as a
decorative appliance when the flue damper is fully open. It
must not be used for any other purpose and must be fitted
in a masonry or factory-built fireplace or ventless firebox
enclosure.
State, provincial or local codes may only allow operation
of this appliance in a vented configuration. Check your
state or local codes. If unvented room heaters are not
permitted, the fireplace vent damper must be locked at the
minimum vent area required by local codes or by the
National Fuel Gas Code (ANSI Z223.1/NFPA 54, latest
edition).
When installed as a Decorative Gas Appliance for
installation in a solid-fuel burning fireplace, a minimum permanent free opening of 29 square inches
must be maintained with a fixed damper stop provided
with the appliance. Minimum flue size for this appliance is 29 square inches.
44
Proposition 65 Warning: Fuels used in gas,
woodburning or oil fired appliances, and the
products of combustion of such fuels, contain
chemicals known to the State of California to
cause cancer, birth defects and other reproductive
harm.
California Health & Safety Code Sec. 25249.6
Installation Precautions
1. This vent-free gas appliance and its components
have been tested and will operate safely when
installed in accordance with this Installation Manual.
Read all instructions before starting the installation,
and follow these instructions carefully during
installation to maximize the appliance's benefit and
safety. Failure to follow them will void your warranty
and may present a fire hazard.
2. After opening the carton, refer to Replacement
Parts on Page 17 and 18, and remove the various
parts.
Report to your dealer if any parts were damaged in
shipment.
•
CFM Specialty Home Products warranty
will be voided by, and CFM Specialty Home
Products disclaims any responsibility for,
the following actions:
• Installation of any damaged appliance.
• Modification of the appliance.
• Installation other than as instructed by
CFM Specialty Home Products.
• Improper positioning of the gas logs.
• Installation and/or use of any component
part or accessory not manufactured or
approved by CFM Specialty Home Products, not withstanding any independent
testing laboratory or other third-party
approval of such component part or accessory.
Any such action may create a possible fire
hazard.
Consult your local building codes.
This heater shall not be installed in a confined
space unless provisions are made for adequate
combustion and ventilation air.
WARNING!
Improper installation, adjustment, alteration,
service or maintenance can cause injury or
property damage. Refe to this manual for
assistance or additional information, consult a
qualified installer, service agency or the gas
supplier.
UVL Series
Installation Requirements
Fresh Air Requirements for
Combustion and Ventilation
WARNING
This heater must have fresh air for proper
operation. If it does not, poor fuel combustion
could result. Read the following instructions to
ensure proper fresh air supply for this and
other fuel-burning appliances in your home.
Modern construction standards have resulted in
homes that are highly energy-efficient and that
allow little heat loss. Your home needs to breathe,
however, and all fuel-burning appliances need fresh
air to function properly and safely. Exhaust fans,
clothes dryers, fireplaces, and other fuel burning
appliances all use the air inside the building. If the
available fresh air supply is insufficient to meet the
demands of these appliances, problems can result.
The vent-free logsets have specific fresh air requirements. You must determine that these requirements
will be met within the space where the appliance will
be installed. The following information will help you
ensure that adequate fresh air is available for the
heater to function properly.
Provide for Adequate Ventilation
Any space within a home can be classified in these
categories:
1) Unusually tight construction
2) Confined space
3) Unconfined space.
First, determine which classification defines the
intended installation space.
Unusually Tight Construction
You must provide additional fresh air if the space
falls into this classification. Unusually Tight Construction is defined as construction wherein:
a. Walls and ceilings exposed to the outside atmosphere have a continuous water vapor barrier with a
rating of one perm or less, with openings gasketed
or sealed, and
b. weather stripping has been added on openable
windows and doors and
c. caulking or sealants are applied to areas such as
joints around windows and door frames, between
sole plates and floors, between wall and ceiling
joints, between wall panels, at penetrations for
plumbing, electrical, and gas lines, and at all other
openings.
UVL Series
If your home meets all of the above criteria, you
must provide additional fresh air for the appliance as
detailed on Page 6.
If your home does not meet the above criteria, follow
the procedure below.
Determine If You Have a Confined or
Unconfined Space
Use the following formula to determine if you have a
confined or unconfined space.
Space is defined as the room in which you will install
the heater, plus any adjoining rooms with doorless
passageways or ventilation grilles between the
rooms. The National Fuel Gas Code defines a
confined space as a space whose volume is less
than 50 cubic feet per 1,000 BTU per hour input
rating (4.8m3 per Kw) of the aggregate (total) input
rating of all appliances installed in that space and an
unconfined space as a space whose volume is not
less than 50 cubic feet per 1,000 BTU per hour
(4.8m3 per Kw) of the aggregate input rating of all
appliances installed in that space. Rooms communicating directly with the space in which the appliances
are installed, through openings not furnished with
doors, are considered a part of the unconfined
space.
1. Determine the volume of space (length x width x
height). Include adjoining rooms connected by
doorless passageways or ventilating grilles.
Example: A room that is 18’ x 12’ x 8’ has a volume
of 1728 cubic feet. An adjoining open kitchen that is
10’ x 12’ x 8’ has a volume of 960 cubic feet. An
adjoining open dining room is 12’ x 12’ x 8’ with a
volume of 1152 cubic feet. The total volume is 3840
cubic feet.
2. Divide the volume of space by 50 cubic feet. The
result is the maximum BTU/hour the space can
support.
Example: 3840 cubic feet divided by 50 = 76.8 or
76,800 BTU/hour.
3. Add the BTU/hour ratings of all fuel-burning
appliances installed in the same space, including the
following:
Gas Water Heater
Gas Fireplace Logs
Vented Gas Heater*
Gas Furnace
Vent-free Gas Heater
Other Gas Appliances*
* Do not include Direct-vent appliances as these use
outdoor air for combustion and vent to the outdoors.
5
Example:
Gas Range
Vent-Free LogSet
Total
55,000 BTU/hour
+25,000 BTU/hour
80,000 BTU/hour
4. Compare the maximum BTU/hour rating the space
can support with the total BTU/hour used by the
appliances.
Example:
76,800 BTU/hour the space can support
80,000 BTU/hour used by appliances
In this example, the maximum BTU/hour that the
space can support is less than the total used by the
appliances.
The space is considered to be Confined Space.
Additional air must be provided to meet the requirements on the vent-free gas log set.
The installation and the provisions for combustion
and ventilation air must conform with the National
Fuel Gas Code, ANSI Z223.1/NFPA 54, or the CSAB149.1 Installation Code (Series).
A confined space may be ventilated in two ways:
A. Open up or provide at least two ventilating grilles to
an adjoining unconfined space. (Fig. 2)
Each of the two grilles must provide an opening of at
least 50 square inches, with all opening dimensions
being at least 3”. One grille must be within 12” of the
ceiling; the other within 12” of the floor. (If the total
exceeds 100,000 BTU/hour, additional grilles will be
needed.)
B. Vent the room directly to the outdoors. (Provide
one square inch of opening for each 4,000 BTU/hr.)
For further information on ventilation guidelines and
sizing specifications, follow the National Fuel Gas
Code/NFPA 54/ANSI Z223.1/NFPA 54, Section 5.3.
If the total BTU/hour used by the appliances is less
than the maximum BTU/hr the space can support,
the room meets the Unconfined Space criteria and
no further ventilation is needed.
WARNING
This heater shall not be installed in a confined
space or unusually tight construciton unless
provisions are made for adequate combustion
and ventilation air.
WARNING
If the area in which the heater may be operated
is smaller than that defined as an unconfined
space, or if the building is of unusually tight
construction, provide adequate combustion and
ventilation air by one of the methods described
in the National Fuel Gas Code, ANSI Z223.1/
NFPA 54, 1992, Sections 5.3, or applicable
codes.
WARNING: Before installing the gas log set in a
solid-fuel burning fireplace, the chimney flue and
firebox must be cleaned of soot, creosote, and loose
paint by a qualified chimney cleaner.
12”
OPTION 1 Vents to
Adjoining
Room
OPTION 3 Vents to
Adjoining
Room
OPTION 2 Remove Door to
Adjoining Room
12”
VO370-2
Fig. 2 Ventilation options for confined spaces.
66
UVL Series
Installation Instructions
WARNING
Do not allow fans to blow directly into the
fireplace. Avoid any drafts that alter burner
flame patterns.
WARNING: Do not use a blower insert, heat
exchanger insert, or other accessory not
approved for use with this gas logset.
DO NOT burn solid fuels in a fireplace where
an unvented gas room heater or logset is
installed.
Any outside air ducts and/or ashdumps in the
fireplace must be permanently closed at time
of appliance installation.
Do not install this appliance in bedrooms or
bathrooms.
WARNING: Any change to this heater or its
controls can be dangerous.
Hole in
Outer
Casing
1”
Gas
Supply
Line
Ceramic
Knockout
Repack
Insulation
Preparing the Fireplace
Gas Line Preparation
Before connecting the appliance, turn off all gas
appliances. Close the main gas valve at the gas
meter or appliances. Close the main gas valve at the
gas meter or LP tank. Make certain there is good
ventilation where the installation will be made.
Installation should comply with all applicable building
codes and ANSI Z223.1/NFPA 54, latest edition, or
CSA B-149.1. Use LP gas-resistant pipe compound
to seal threaded joints.
Installation to Existing Gas Line
There should be a manual ON/OFF valve within
easy reach of the appliance. If not, before installation
of the appliance make certain a valve is installed.
There may be a second valve on the line close to the
point where the fireplace line branches off the main
gas supply line. During installation, make certain this
valve is OFF.
Manufactured Fireplace Preparation
Refer to the manufacturer’s fireplace installation
manual for the specific method of running the gas
line into the fireplace. The following method is typical
of most manufactured fireplaces.
Insert a 1/2” gas pipe through the gas line tube provided by the manufacturer, from outside the fireplace,
as marked by the manufacturer. An ON/OFF valve
should be placed within easy reach of the appliance.
After the gas supply is installed, reinstall the insulation
removed from the gas line tube, and pack it around the
pipe, to prevent cold air entry and to protect the gas
line. (Fig. 3)
NOTE: The gas pipe should not come into contact
with any wood structure until it has reached a point
at least one (1) inch away from the fireplace side.
(Fig. 3)
UVL Series
Gas Access
Holes
Electrical
Access
Outside Air Access
760
Fig. 3 Gas line installation - factory built fireplace.
Masonry Fireplace Installation
Preparation
A 1/2 inch gas supply line must be supplied to the
firebox. In most cases, this will require drilling a gas
line access hole through the masonry wall. The gas
supply line should then be sealed in the access hole
with mortar. The gas supply line should also have a
valve within easy reach of the appliance. Use only
1/2” rigid pipe or approved 3/8” copper tubing. (Do
not use cast-iron pipe).
Clean the fireplace and chimney (if used) of any
ashes, soot, creosote, or obstruction. This will
minimize any smell from the fireplace. We recommend cleaning by a chimney sweep.
Flue Damper Preparation
The vented fireplace damper should be fully opened
when operating the appliance as a vented log set. A
damper stop clamp with set screw is provided as a
means to prevent full closure of the fireplace damper
blade. The clamp is designed to prevent accidental
closure of the damper when in use. (Fig. 4) (If the
damper stop cannot be installed, the installer should
install a permanent damper stop that will keep the
damper open a minimum of 1¹⁄₂”).
7
Damper Stop Installation
Damper Locking Bracket
When installing a decorative gas appliance in a
fireplace, some local codes require a damper stop
be added so the damper will not close completely.
The CFM Corporation damper stop is designed so
the damper can be locked in the closed position, and
still allow a vent for the pilot gasses.
This damper stop is designed to work on all CFM
Specialty Home Products BR, BC, SR, SC, TF and
TL series fireplaces.
Installation Instructions
1. Open damper. The damper must be open to
attach the damper stop.
Attachment
Screws (2)
2. Locate the damper locking bracket. From inside
the fireplace locate the damper locking bracket on
the left side of the combustion dome. (Fig. 4)
3. Align the two slots on either side of the cutout on
the damper stop with the two small holes on the
angled portion of the damper locking bracket.
Attach the damper stop with the screws provided.
(Fig. 5)
NOTE: Some of the early units may not have the
holes in the end of the damper locking bracket. If this
is the case use the damper stop as a template to drill
two (2) 1/8” holes in the damper locking bracket to
mount the damper stop.
Damper Stop
DP101
Fig. 5 Attach damper stop.
Damper
Stop
Damper Stop
Damper Locking Bracket
Typical Manufactured
Fireplace
Typical Masonry
Fireplace
DP105
Fig. 6 Damper stop placement.
DP100
Fig. 4 Locate damper locking bracket.
88
UVL Series
7A
7B
Front View
7C
Without Hood
With Hood
8”
42”
Noncombustible
Material
3¹⁄₂” Min.
Flat
Mantel
Shelf
Stand-off
8”
38¹⁄₂”
4”
Stand-off
20”
12”
7¹⁄₂”
3¹⁄₂”
Min.
Noncombustible
Facing Material
Seal with
Noncombustible
Material
4”
762
4” Hood
Top View
Mantel Trim
Finished Wall
Material
Firebox
11”
3¹⁄₂”
Noncombustible Facing
Material
Front
Edge of
Grate
763
3”
764
765
Fig. 7 Mantel clearances.
Burner Assembly Location
Centrally locate the unit in the fireplace, far enough
back into the firebox to accomplish adequate draft (if
use as a vented appliance is planned). Ensure that
the front grate feet sit inside the front edge of the
fireplace a minimum of 3”. (Fig. 7B)
Clearances
(Refer to Fig. 7, Page 9)
To ensure the safe installation into a masonry or
factory-built fireplace, carefully observe the following
instructions:
1. Sidewall Clearances: The clearance from the
inside of the front opening of the fireplace to any
combustible wall should not be less than 3¹⁄₂” (Fig.
7A)
2. Ceiling Clearances: The ceiling height should not
be less than 42” from the top of the fireplace opening.
(Fig. 7A)
3. Mantel Clearances:
When installing an ANSI Z21.11.2 ventless appliance, the finishing material used for the mantel must
be rated at 250°F or greater. Refer to firebox instructions for any further information.
Without hood: If no hood is installed, then there
must be non-combustible material from the top front
opening of the fireplace to a height of at least 20
inches and the full width of the fireplace. A combustible flat mantel shelf can be no closer than 38¹⁄₂”
from the top front of the fireplace opening (Fig. 7B).
With hood: If a hood is installed there must be noncombustible material from the top front opening of
the fireplace to a height of 7¹⁄₂” and the full width of
the fireplace. A combustible flat mantel shelf may be
installed according to the detail in Figure 7C.
3A. Mantel Depth:
A combustible mantel can be no deeper than 8”, at
12” above the hood. (Figs. 7B and 7C)
4. Grate Clearance
The minimum clearance between the front legs of the
grate and the front edge of the fireplace is 3” (Fig. 7B).
UVL Series
9
Gas Line Connection
WARNING
Check the gas type. Use only the gas type indicated
on the appliance rating plate. If the gas listed on the
plate is not the type of gas supplied, DO NOT
INSTALL the logset. Contact your dealer for the
proper model.
Connection directly to an unregulated LP tank
can cause an explosion.
Always use an external regulator for all LP appliances, to reduce the supply tank pressure to a
maximum of 14” w.c. This is in addition to the
regulator fitted to the heater.
The normal gas connection is made at the right side
(facing the unit). If a left-side connection is desired,
the connecting pipe may be directed under or behind
the rear of the appliance, to terminate at the righthand side for connection to the inlet of the appliance.
Connect the appliance to the gas line using fittings
and aluminum tubing provided.
Close the valve knob on the appliance, turn the main
gas supply valve ‘ON’, and carefully check all gas
connections for leaks, with a soapy water solution or
a sniffer. DO NOT TEST FOR LEAKS WITH AN
OPEN FLAME.
Upon completing your gas line connection, a small
amount of air will be in the gas lines. When first
lighting the pilot, it will take a few minutes for the
lines to purge themselves of air. Once the purging is
complete, the pilot and burner will light and operate
as indicated in this manual. Subsequent lightings of
the appliance will not require purging.
Check the inlet pressure to the appliance, to ensure
that it is as shown in the table on page 3. The
minimum is for the purpose of input adjustment.
The pressure is controlled by the regulator and
should be checked at the pressure test point located
in the control valve body. Access to the pressure
test point is obtained by removing all logs. (UVL-M
series only)
During the initial purging and subsequent
lightings, never allow the gas valve control
knob to remain depressed in the ‘Pilot’
position without lighting the pilot with a match
or piezo ignitor.
There is a possibility of odor fade in LP. Never
install an LP appliance or service line below
grade without a gas detector.
Positioning the Logs
The logs must be positioned on the grate and
locating pins, as shown in Figure 8. Make sure each
bottom log engages the locator pins on the grate,
and top logs are properly positioned in notches on
tops of bottom logs.
Gas logs must be properly positioned or the appliance will not function properly, and may result in
soot accumulation on the inside of the firebox and/or
on the gas logs. Make sure there is no yellow
flame impingement on the logs which could
result in excessive carbon monoxide emissions
and carboning.
The optional volcanic rock may be applied to the
hearth around the burner assembly.
Never place any other material on the burner.
WARNING
Failure to position the parts in accordance
with these diagrams or failure to use only
parts specifically approved for use with this
appliance may result in property damage or
personal injury.
The pressure should be checked with the appliance
burning and the control set on ‘HIGH’.
The pressure regulator is preset and locked to avoid
tampering. If the pressure is not as specified,
replace the regulator. Refer to Replacement Parts.
After measuring the pressure, replace the test point
plug. Ensure there are no leaks, then place the logs
in their specified positions.
1010
UVL Series
UVL18
UVL24
UVL30
LG112
LG114
LG113
Fig. 8 Positioning logs on grate assembly.
I
L
ON
PI
LO
T
1. Thread wire through the electrical knockout
located on either side of the fireplace. Do not cut the
wire or insulation on metal edges. Ensure that the
wire is protected. Run the other end to a conveniently-located wall receptacle box.
TP
(RN and RP models only)
O H
TH
5. Remote wall switch
TPTH
The fireplace screen must be in place when the
appliance is operating, and unless other provisions
for combustion air are made, the screen must have
openings for the introduction of combustion air.
Control Knob
To Wall Switch
OFF
Fireplace Screen
Piezo Ignitor
Hi/Lo Knob
751
Fig. 9 Connecting a wall switch to the valve terminals.
(UVL-R Series only)
2. Attach the wire to the switch and install the switch
into the receptacle box. Attach the cover plate to the
switch.
3. Connect the wiring to the gas valve. One wire
connects to the ‘TP/TH’ terminal; the other attaches
to the ‘TH’ terminal. (Fig. 10)
NOTE: If any of the original wire as supplied with the
appliance must be replaced, it must be replaced with
a wire of at least a 60°C temperature rating.
UVL Series
11
Operating Instructions
The First Firing
On completing the gas line connection, a small
amount of air will be trapped in the gas line. When
you first light the unit with the pilot light, it will take a
few minutes to purge the trapped air. Once you have
purged the gas line, the pilot and burner will light and
operate normally. Subsequent lightings of the
appliance will not require purging the gas line.
When lit for the first time, the appliance will emit a
slight odor for an hour or two. This is due to paint
and lubricants used in the manufacturing process
curing under heat. This is normal. You may wish to
have the windows open to dissipate any odors
during the curing process.
Red Glow
LG115
Fig. 13 UVL18 proper burner flame appearance.
Control Knob
Red Glow
I
L
ON
TPTH
O H
T
LO
PI
TP
LG116
OFF
TH
Fig. 14 UVL24 proper burner flame appearance.
Hi/Lo Knob
Piezo Ignitor
HV101a
Fig. 10 Honeywell control valve.
Red
Glow
HI
Piezo
Ignitor
OFF
OT
LO
PIL
LG117
FP1036
Fig. 15 UVL30 proper burner flame appearance.
Fig. 11 EuroSIT control valve.
OT
PIL
R Series
O FF
Thermopile
TH
HI
O FF
P I L OT
ON
OFF
A
TP
THTP
LO
E
Thermocouple
FP1395
Fig. 12 SIT control valve.
Flame Appearance
M Series
Thermopile
To obtain proper operation, it is imperative that the
pilot and main burner flame characteristics are
steady, not lifting or floating. Refer to Figure 13 -15
for proper burner flame appearance. Refer to Figure
16 for proper pilot flame appearance.
Typically, the top 1/8” of the thermopile should be
engulfed in the pilot flame. (Fig. 16)
1212
752
P103
Fig. 16 Proper pilot flame.
UVL Series
Lighting And Operating Instructions
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING:If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
A. This heater has a pilot which must be lit manually.
When lighting the pilot follow these
instructions exactly.
B. BEFORE LIGHTING smell all around the heater
area for gas. Be sure to smell next to the floor
because some gas is heavier than air and will
settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any fireplace
• Do not touch any electric switch
• Do not use any phone in your building
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
•
If you cannot reach your gas supplier, call the
Fire Department
C. Use only your hand to push in or turn the gas
control knob. Never use tools. If the knob will not
push in or turn by hand, do not try to repair it, call a
qualified service technician. Applying force or any
attempted repair may result in a fire or explosion.
D. Do not use this fireplace if any part has been under
water. Immediately call a qualified service technician to inspect the heater and to replace any part of
the control system and any gas control which has
been under water.
Lighting Instructions
1. STOP! Read the safety information above.
2. Turn off all electrical power to the fireplace.
3. For MN/MP/TN/TP appliances ONLY, go on to
Step 4. For RN/RP appliances turn the On/Off
switch to “OFF” position or set thermostat to
lowest level.
4. Open control access panel.
5. Push in gas control knob slightly and turn
to "OFF".
clockwise
3/8" - 1/2"
OFF
3 4 5
OFF
Euro SIT
SIT NOVA
ON
OFF
OT
L
PI
ON
1 2
P
OFF ilot
PILOT
10. Push the control knob all the way in and hold.
Immediately light the pilot by repeatedly
depressing the piezo spark ignitor until a flame
appears. Continue to hold the control knob in for
about one (1) minute after the pilot is lit. Release
knob and it will pop back up. Pilot should remain
lit. If it goes out, repeat steps 5 through 8.
Honeywell
6. Wait five (5) minutes to clear out any gas. Then
smell for gas, including near the floor. If you
smell gas, STOP! Follow "B" in the safety
information above. If you do not smell gas, go
to the next step.
7. Remove glass door before lighting pilot. (See
Glass Frame Removal section).
8. Visibly locate pilot by the main burner.
9. Turn knob on gas control counterclockwise
to "PILOT".
•
If knob does not pop up when released, stop
and immediately call your service technician or
gas supplier.
•
If after several tries, the pilot will not stay lit,
turn the gas control knob to "OFF" and call your
service technician or gas supplier.
11. Replace glass door.
12. Turn gas control knob to “ON” position.
13. For RN/RP appliances turn the On/Off switch to
“ON” position or set thermostat to desired setting.
14. Turn on all electrical power to the fireplace.
To Turn Off Gas To Heater
1. Turn the On/Off switch to Off position or set the
thermostat to lowest setting.
2. Turn off all electric power to the fireplace if
service is to be performed.
3. Open control access panel.
UVL Series
4. Push in gas control knob slightly and turn
clockwise
to "OFF". Do not force.
5. Close control access panel.
13
Troubleshooting
Honeywell Valve (UVL-R series)
START
CHECK
Gas supply on
NO
• Supply line hooked up
• Shutoff valve open
NO
• Lockout has engaged. Wait 60 seconds
and try again
• Piezo screws are tight for good ground
• For spark at electrode while depressing
piezo - 1/8” gap to pilot hood needed
• All wiring connections
• Replace piezo ignitor
YES
Pilot lights with Piezo
YES
Pilot stays lit
NO
• For air in the lines
• Thermopile needs a minimum of 325mV
• All wiring connections
• Replace thermopile
• Thermocouple needs a minimum of 14mV
• Defective valve. turn to pilot, meter should
read greater than 100mV. If not, replace the
valve.
YES
Pilot lights main
burner
NO
• Valve turned on
• Wall switch is not turned on
• Thermopile needs a minimum of 325mV
• Plugged burner
YES
System OK
1414
UVL Series
Troubleshooting
SIT 630 Eurosit Valve (‘M’ Series)
With proper installation and maintenance, your new Gas Appliance should provide years of trouble-free
service. If you do experience a problem, this guide will help a CERTIFIED SERVICE PERSON in the
diagnosis of problems and the corrective action to take.
SYMPTOM
1. Pilot will not light with
piezo ignitor or match.
POSSIBLE CAUSES
A. Main shutoff valve closed.
B. Air in the gas line.
C. Pilot orifice plugged, not
letting gas flow.
2. Pilot will not stay lit
after carefully
following the lighting
instructions.
UVL Series
1. Make sure that the shutoff valve located on the pipe
supplying gas to the fireplace is open.
1. Light a match, turn gas valve knob to ‘PILOT’ position
and depress. Keep match near pilot burner till it lights.
1. Replace the burner assembly.
D. No gas supply to the
fireplace.
1. Check plumbing to see if gas fireplace has been
hooked up to the gas supply line.
2. Propane tank is empty.
A. Defective thermocouple.
1. Replace burner assembly.
B. Thermocouple fitting not
tight in valve.
1. Carefully tighten the fitting.
C. Weak pilot flame.
1. The pilot flame must engulf the thermocouple. Clean for
maximum flame impingement on the thermocouple.
(Fig. 12)
1. Replace the burner assembly.
D. Defective valve.
3. No gas to main
burner with pilot
flame burning and
valve turned to
‘High-Low’ range.
CORRECTIVE ACTION
E. Not enough oxygen in the
room. (Danger!)
1. Open the door and get fresh air at once!
A. Plugged main burner
orifice.
1. Replace the burner assembly.
B. Defective valve.
1. Replace the burner assembly.
15
Maintenance and Safeguards
Keep the control compartment, logs and burner area
around the logs clean by vacuuming or brushing at
least twice a year. At altitudes above 4,500 feet
(1370m) monthly cleaning is recommended.
THE LOGS CAN GET VERY HOT. HANDLE ONLY
WHEN COOL.
Always turn off gas to the pilot before cleaning. For
relighting, refer to the lighting instructions.
The appliance and venting system (if used) should be
inspected before initial use, and at least annually by
a qualified field service person.
Always keep the appliance area clear and free from
combustible materials, gasoline, and other flammable
vapors and liquids.
Never obstruct the flow of combustion and ventilation
air. Keep the front of the appliance clear of all obstacles and materials.
Leave clearance of at least 36” from the front of the
fireplace.
Although your gas logs are very realistic in appearance, the fireplace must not be used for burning any
solid fuels.
To avoid irreparable damage to the appliance or
personal injury, matches, paper, garbage, or any
other material must not be placed or thrown on top of
the logs or into the flames.
To avoid personal injury, do not touch hot surfaces
when the appliance is operating. Touch only the valve
control knob. Avoid contact with the grate feet or
prongs, or any other part which may be very hot.
Always ensure that the fireplace screen is closed
when the appliance is operating.
Any safety screen or guard removed for servicing the
appliances must be replaced before operating the
appliance.
Close supervision is necessary when the appliance is
being operated near children.
The appliance is intended for use as a gas heater
mounted in a vented or unvented fireplace as described in the installation section of these instructions. It should not be used for any other purpose.
Inspecting the Venting System
A vented fireplace venting system is designed and
constructed to develop a positive flow adequate to
remove flue gasses to the outside atmosphere. See
vented fireplace installation instructions.
In extreme situations, carbon monoxide poisoning or
suffocation may occur.
Periodic examination and cleaning of the venting
system of the solid-fuel burning fireplace must be
done frequently by the home owner or a qualified
agency.
UVL System Maintenance
The UVL burner and control system consists of:
• Chassis
• Gas Orifice
• Grate assembly
• UVL18 - four (4) decorative logs
UVL24 - five (5) decorative logs
UVL30 - seven (7) decorative logs
• Gas valve assembly
• Pressure regulator (UVL18M and UVL24M only)
Most of these components require only occasional
check-up and cleaning. Some may require adjustment. If repair is needed, it should be performed by
a qualified technician.
In order to properly clean the burner and pilot
assembly, turn off the gas to the unit and remove the
logs, exposing the burner and pilot assembly. Clean
all foreign materials from the top of the burner.
Check to make sure that all burner parts are clean.
Visually inspect the pilot. Brush or blow away any
dust or lint accumulations.
NOTE: The burner and pilot assembly should be
checked for any dust or lint at least every six
months.
Replacement Parts
Contact the factory for questions about prices and
policies covering replacement parts. Parts will be
shipped at prevailing prices. Normally, all parts can
be ordered through your CFM Specialty Home
Products distributor or dealer.
When ordering replacement parts, always give the
following information:
1. The model number of the appliance.
2. The part number
3. The description of the part. (See the Replacement Parts List on Page 17)
4. The installation date of the appliance.
If you need more information, beyond what the
dealer can furnish, contact CFM Specialty Home
Products, 410 Admiral Blvd, Mississauga, Ontario,
Canada L5T 2N6, Attention: Director of Technical
Service
Any foreign objects in the venting system, except
those designed specifically for the venting system,
may cause spillage of the flue gases into the room.
1616
UVL Series
1
c
2
f
4
b
c
a
g
5
3
e
d
8
Piezo Ignitor
9a,b
LO
6a,b
c,d
Screw
PILOT
F
HI
OF
7
10
20
ON
TPTH
O H
I
PI
LO
T OFF
TP
11
L
12a,b
TH
14a,b
15a,b
13a,b
16
17
19
21a,b
18a,b
957
CFM Specialty Home Products reserves the right to make changes in design, materials, specifications, prices and discontinue colors and
products at any time, without notice.
UVL18/24/30 Premium Vent Free Gas Logs
Ref.
1.
1a.
1b.
1c.
1d.
1e.
1f.
UVL Series
Description
Complete Log Set
Back Log
Right Cross Log
Left Cross Log
Front Log
Middle Log
Middle Left Log
UVL18
20001420
7583180
-7583181
7583178
7583179
--
UVL24
20001421
7583175
7583177
7583176
7583173
7583174
--
UVL30
20001893
20001892
20001886
20001889
20001890
20001891
20001888
17
UVL18/24/30 Premium Vent Free Gas Logs
Ref.
1g.
2a.
2b.
3.
4.
5.
6a.
6b.
6c.
6d.
7a.
7b.
8.
9a.
9b.
10.
11.
12a.
12b.
13a.
13b.
14a.
14b.
15a.
15b.
16.
17.
18a.
18b.
19.
20.
21a.
21b.
1818
Description
Middle Right Log
3/8” Flare Tubing
3/8” Flare Tubing (M Series)
Volcanic Rock
Elbow Fitting 1/2” NPT (F) x 3/8” Flare
Damper Stop
or
Burner Supply Assembly - Main Orifice (RP)
Burner Supply Assembly - Main Orifice (RN)
Burner Supply Assembly - Main Orifice (MN)
Burner Supply Assembly - Main Orifice (MP)
Orifice Hood - Front (MP,RP)
Orifice Hood - Front (MN, RN)
Front Leg Assembly
Gas Valve - SIT - MN Series
Gas Valve - SIT - MP Series
Valve Cover - M Series (includes Piezo & Screw)
Piezo Ignitor - M Series & R Series - SIT Valve
Pilot Assembly - MN Series
Pilot Assembly - MP Series
Gas Valve - Honeywell - RP
Gas Valve - Honeywell - RN
Knob Extension (Hi/Lo) - Honeywell Valve
Knob Extension (HI/LO) - SIT Valve
Knob Extension (ON/OFF) - Honeywell Valve
Knob Extension (ON/OFF) - SIT Valve
Piezo Ignitor - R Series - Honeywell Valve
Piezo Extension (R Series only)
Pilot Assembly - RP
Pilot Assembly - RN
Ignitor Cable (M and R Series)
Access Panel Assembly
Gas Valve - SIT - RN
Gas Valve - SIT - RP
UVL18
-7060120
20004146
20000198
7523184
7540310
3030176
20000120
20000119
20000121
20000122
20000134
20000130
3081122
20001354
20001355
51851
52464
20001356
20001357
10000242
10000235
20000006
55162
20000007
55163
20000062
20001427
55465
55464
20004419
3085109
55463
55462
(continued)
UVL24
-7060120
20004146
20000198
7523184
7540310
3030176
20000124
20000123
20000125
20000126
20000133
20000132
3081122
20001786
20001787
51851
52464
20001356
20001357
10000242
10000235
20000006
55162
20000007
55163
20000062
20001427
55465
55464
20004419
3081120
55463
55462
UVL30
20001887
7060120
-20000198
7523184
7540310
3030176
20001878
20001877
20001875
20001876
30000339
30000337
20001862
20001786
20001787
51851
52464
20001356
20001357
10000242
10000235
20000006
55162
20000007
55163
20000062
20001427
55465
55464
20004419
20001860
55463
55462
UVL Series
Accessories
The following accessories are available from your Vermont Castings Dealer. If you need additional information beyond what your dealer can supply, contact CFM Specialty Home Products, 410 Admiral Blvd, Mississauga, Ontario, Canada L5T 2N6, Attention: Technical Service.
Accessory
Description
Required to protect wall above
fireplace and/or mantel in certain
applications.
Model Number
AH3244BK (BLACK)
AH3244PB (POLISHED
BRASS)
AC100
Contact CFM Specialty Home Products with questions concerning prices and policies covering replacement parts. Parts may be ordered through your
Vermont Castings distributor or dealer.
You will need the following information when ordering
replacement parts:
• The appliance model number.
• The serial number.
• A description of the part.
Should you need additional information beyond what
your dealer can furnish, contact:
CFM Specialty Home Products
410 Admiral Blvd.
Mississauga, Ontario
Canada L5T 2N6
UVL Series
Model and serial numbers are listed on the rating
plate (located on right side of combustion chamber).
Record your model and serial number here for
future reference.
Model #__________________________________
Serial # __________________________________
19
2020
UVL Series
LIMITED 2/20 YEAR WARRANTY
For VERMONT CASTINGS® Vent-Free Gas Appliances
CFM Specialty Home Products (Company) extends the
warranties specified in paragraphs A and B below with
respect to its VERMONT CASTINGS Decorative Gas
Appliances (the “Gas Appliance”), including the CFM
Specialty Home Products supplied accessories and
components referred to in those paragraphs, subject to the
following conditions and limitations:
(1) These warranties are extended only to the Gas
Appliance installed in the continental United States,
including Alaska, and Canada; only if and so long as the
accordance with the installation and operating instructions
furnished therewith; and only if and so long as Gas Appliance is not removed from its original installation.
(2). These warranties are limited to only the component
parts manufactured and supplied by CFM Specialty Home
Products. The use of components manufactured by others
with the Gas Appliance could create serious safety hazard,
may result in the denial of certification by recognized
national safety agencies, and could be in violation of local
building codes.
(3). The Gas Appliance must be operated at all times in
accordance with the operating instruction furnished therewith. The Gas Appliance is designed to burn either natural
or propane gas only. Burning conventional fireplace fuels
such as wood, coal, or any other solid fuel will cause
damage to the Gas Appliance, will produce excessive
temperatures and will result in a fire hazard.
(4). These warranties are limited to repair, replacement or
furnishing a replacement for sale, as specified in Paragraphs A and B, for a part found to CFM Specialty Home
Products satisfaction, after examination, to be defective in
materials or workmanship under normal conditions, use and
service.
(5). All obligations with respect to these warranties may
be fully discharged by CFM Specialty Home Products
refunding the wholesale price of a defective part.
(6) Except as otherwise expressly specified in Paragr
aphs A and B. NONE OF THESE WARRANTIES COVER,
AND CFM SPECIALTY HOME PRODUCTS SHALL NOT
BE RESPONSIBLE FOR, ANY CONSTRUCTION, INSTALLATION, LABOR, TRANSPORTATION OR OTHER COSTS
OR EXPENSES ARISING FROM A DEFECTIVE PART, ITS
REPAIR OR REPLACEMENT OR OTHERWISE, NOR
SHALL CFM SPECIALTY HOME PRODUCTS IN ANY
EVENT BE RESPONSIBLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES. EXCEPT TO
THE EXTENT PROVIDED BY LAW, THERE ARE NO
IMPLIED WARRANTIES WITH RESPECT TO THE GAS
APPLIANCE, ITS COMPONENTS AND ACCESSORIES
(INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE),
UVL Series
ALL OF WHICH ARE HEREBY EXPRESSLY INCLUDED.
IN NO EVENT SHALL ANY IMPLIED WARRANTY PRESCRIBED BY LAW (NOTWITHSTANDING THE FOREGOING EXPRESS EXCLUSION) REMAIN IN EFFECT AFTER
EXPIRATIONS OF THE WARRANTIES SET FORTH IN
PARAGRAPHS A AND B.
A. Gas Appliances, electrical and manual compon
ents, glass panels, all sealants or adhesives and
optional accessories (exclusive of CFM Specialty Home
Products supplied decorative logs which are covered by a
separate warranty under paragraph B below):
Within two years from the date of manufacture of the gas
appliance, CFM Specialty Home Products will repair, or
replace (at our option) a defective part without charge.
B. CFM Specialty Home Products cement logs, fiber
logs, or firebox liners:
Within two years from the date of manufacture of the gas
appliance, CFM Specialty Home Products will replace a
defective part without charge. Within years three through
twenty from the date of manufacture of the gas appliance,
CFM Specialty Home Products will provide a replacement
for a defective part to the homeowner, but assumes no
liability for incurred labor cost.
The foregoing warranties gives you specific legal rights
and you may also have other rights which vary from state to
state. Some states do not allow limitations on how long an
implied warranty may last, so the limitation specified above
on the duration of any implied warranty prescribed by law
may not apply to you. Similarly, some states do not permit
the exclusion or limitation of incidental or consequential
damages, so the above exclusion of such damages may not
apply to you.
In order to obtain performance of any of the above
warranty obligations, write to CFM Specialty Home Products
at this address:
CFM Specialty Home Products
410 Admiral Blvd.
Mississauga, Ontario Canada L5T 2N6
Attention: Director of Warranty Services
Since local building requirements may vary greatly
throughout the country, users of CFM Specialty Home
Products products should determine in advance whether
there are any building
code restrictions on the use of a specified product.
CFM SPECIALTY HOME PRODUCTS MAKES NO REPRESENTATION OR WARRANTY REGARDING, AND SHALL
NOT BE RESPONSIBLE FOR, ANY BUILDING CODE
COMPLIANCE.
The foregoing warranties give you specific legal rights and you may
also have other rights which vary from state to state.
21
CFM Specialty Home Products
410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 • 905-670-7777
www.majesticproducts.com • www.vermontcastings.com
© CFM Specialty Home Products
Download PDF

advertising