Aiwa | XP-ZV550 | Operating instructions | Aiwa XP-ZV550 Operating instructions

Highlighted letters in the text of this manual correspond to the illustrations.
PRECAUTIONS
To maintain good performance
XP-SR321/XP-SR320
COMPACT DISC PLAYER
OPERATING INSTRUCTIONS
8B-HCD-901-01
010205AYG-O9
Printed in Indonesia
OWNER’S RECORD
For your convenience, record the model number and the serial number
(you will find it on the bottom of your set) in the space provided below.
Please refer to them when you contact your Aiwa dealer in case of difficulty.
Model No.
Serial No.
NOTE
FOR USE IN THE U.S.A.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Modifications or adjustments to this product, which are not expressly
approved by the manufacturer, may void the user’s right or authority to
operate this product.
• Do not use the unit in places which are extremely hot, cold, dusty or humid. In
particular, do not use or keep the unit in following places.
• in a high humidity area such as a bathroom
• near a heater
• in an area exposed to direct sunlight (e.g., inside a parked car, where it can
become extremely hot)
• near sources of strong magnetism, such as televisions, speakers, or magnets
• where there is a lot of movement or vibration, such as on a car dashboard or
an unstable shelf
• Do not open the battery compartment with wet hands.
• Wipe the unit thoroughly before inserting batteries and after use.
• Do not soak the unit in water.
For safety
• Do not attempt to disassemble the unit. Laser rays from the optical pickup are
dangerous to the eyes.
• Make sure that pins or other foreign object do not get inside the player.
• Take care not to drop the unit or subject it to strong shocks.
• To keep dust from the pickup lens, keep the disc compartment lid closed after
use. Never touch the lens.
• If you hear no sound when playing a disc, DO NOT turn the volume up high
because music could suddenly start at high volume. Turn the volume control to
the lowest level before starting playback and slowly turn it up to the desired level.
Note on listening with the headphones
• Listen at moderate volumes to avoid hearing damage.
• Do not wear the headphones while driving or cycling. It may create a traffic
hazard.
• You should use extreme caution or temporarily discontinue use in potentially
hazardous situations, such as walking, jogging, etc.
• Wear them properly; L is left, R is right.
Note on condensation
If the unit is suddenly moved from a cold place to a warm one, it may result in
condensation on the pickup lens and malfunction or playback difficulties.
Should this occur, leave the unit for a few hours, then try to playback again.
MAINTENANCE
To clean the lens → A
If the lens becomes dirty, the player will skip or not play. If this occurs, clean the
lens in the following manner.
To remove dust or dry particles, first use a camera lens blower/brush a to blow
a few times to loosen particles, then gently brush the lens b clean. Finish by
blowing the lens again.
To remove fingerprints, use a cotton swab dipped in lens cleaning solution. Wipe
gently from the center to the edge. Lens cleaning solution is commercially available.
Note
A
Take care not to get too much solution on the swab, which could flow into the unit
and cause damage.
Pressing too strongly with the swab could scratch or break the lens.
To clean the discs → B
Before playing, wipe the disc from the center outward with a cleaning cloth. After
playing, store the disc in its case.
SPECIFICATIONS
Tracking system
Laser pickup
D/A conversion
Frequency response
Output
Frequency range
B
C1
3-beam laser
Semiconductor laser
4-times oversampling digital filter + 1-bit DAC
20 – 20,000 Hz
PHONES/LINE OUT jack (stereo mini-jack)
AM: 530/531 kHz – 1,710/1,602 kHz
(10 kHz/9 kHz steps)
FM: 87.5 – 108 MHz
Maximum output
12 mW + 12 mW (16 ohms at 1 kHz)
500 mV (47 k ohms at 1 kHz)
Power supply
DC 3 V using two size AA (LR6) alkaline
batteries
DC 2.4 V using two commercially available
(Ni-Cd 1.2 V 700 mAh) rechargeable batteries
AC house current using the supplied AC adaptor
Maximum outside dimensions
134 (W) × 32.5 (H) × 141 (D) mm
(excluding projecting parts and controls)
(5 3/8 × 1 5/16 × 5 5/8 in.)
Weight
Approx. 294 g (10.3 oz.) excluding batteries
Accessories
AC adaptor AC-D603 (1)
Stereo headphones (1)
Carrying case (XP-SR321 only) (1)
AC adaptor AC-D603U
Rated input: AC 120 V, 60 Hz
The specifications and external appearance of this unit are subject to change
without notice.
C1
AC adaptor AC-D603U
Stereo headphones (1)
Carrying case (XP-SR321 only) (1)
Rated input: AC 120 V, 60 Hz
The specifications and external appearance of this unit are subject to change
without notice.
USING ON DRY CELL BATTERIES → C
2
3
1 Set the dial to the OPEN position to open the disc compartment, then
open the battery compartment.
2 Insert two size AA (LR6) alkaline batteries with the 0 and 9 marks
correctly aligned. After batteries insertion, close the battery compartment
firmly.
3 Close the disc compartment tightly and set the dial to the LOCK position.
Battery replacement
The battery indicator in the display changes from
to
to
according
to the remaining power of the batteries. Replace the batteries when
lights.
If the unit remains in use after
lights, “Lo-bAtt” appears and operation stops.
To maintain preset data
When replacing the batteries, the unit will retain the preset station frequencies
for about 1 minute. To prevent the erasure of the memories, replace the batteries
within 1 minute.
• Before replacing the batteries, turn off the power by pressing
sSTOP/OFF/CHARGE.
• DO NOT press any keys while replacing the batteries, otherwise it will not
retain preset data for 1 minute.
D
Battery life (using alkaline batteries LR6)
The setting of the E•A•S•S switch
48
12 or OFF
Battery life
Approx. 27 hours
Approx. 19 hours
Battery life may vary depending on conditions of use.
If the cover of the battery compartment comes off → D
Note
Close the battery compartment firmly, or the compact disc may be
damaged.
Note on dry cell batteries
• Make sure that the 0 and 9 marks are correctly aligned.
• Do not mix the different types of batteries, or an old battery with a new one.
• To prevent the risk of electrolyte leakage or explosions, never recharge the
batteries, apply heat to them, or take them apart.
• When not using the batteries, remove them to prevent needless battery wear.
• If liquid leaks from the batteries, wipe thoroughly to remove.
XP-SR321/SR320(AU)E
1
E1
USING ON RECHARGEABLE BATTERIES → E
2
• Be sure to use size AA Ni-Cd 1.2 V 700 mAh rechargeable batteries, which are
commercially available.
• Be sure to read the instructions of the purchased rechargeable batteries before
use.
• When using on rechargeable batteries for the first time, charge them until the
battery indicator goes out.
• Before charging the batteries, close the disc compartment. You cannot charge
the batteries while it is opened.
DC 5~6V
3
STOP/OFF
CHARGE
1 Insert the rechargeable batteries with the 0 and 9 marks correctly
aligned.
2 Connect the AC adaptor.
Pull out the rubber cap before connecting the adaptor.
1 to DC 5 ~ 6 V jack
2 to a wall outlet
3 Keep sSTOP/OFF/CHARGE pressed for about 1 second to start charging.
“C-On” appears, and the battery indicator blinks.
When charging is completed, “C-OFF” flashes a few times, and the battery
indicator goes out.
After charging, disconnect the AC adaptor.
Time to recharge the batteries
Recharge the batteries when
lights. If the unit remains in use after
lights, “Lo-bAtt” appears and the current operation stops.
To stop charging
Press sSTOP/OFF/CHARGE during charging.
F
Force charging
When the recharging stops after only few minutes or the batteries cannot be fully
recharged, press sSTOP/OFF/CHARGE while pressing PLAY MODE to start
force charging.
STOP/OFF
CHARGE
PLAY/PAUSE
ATTENTION:
The product you have purchased can be powered by
nickel cadmium batteries which are recyclable. At the
end of their useful life, under various state and local
laws, it is illegal to dispose of these batteries into your
municipal waste stream.
Please call 1-800-289-2492 for information on how to
recycle these batteries.
G
USING ON AC HOUSE CURRENT
Connect the supplied AC adaptor in the same way as when recharging the
batteries.
During operation on AC house current, all of the battery indicator disappears.
DSL
PLAY/PAUSE
BEFORE PLAYBACK
HOLD switch → F
VO
LU
M
E
PLAY MODE
Release the HOLD switch before playback. → a
When not using the unit, set the HOLD switch to the HOLD position. → b
Accidentally pressed button will not function.
If buttons are pressed when the HOLD switch is set to the HOLD position, “HOLd”
flashes in the display.
Turning on and off → F
Turning the power on
Press ePLAY/PAUSE. Power is turned on and playback starts.
Note
H1
“Err” appears on the display in the following cases:
– When you try to play the unit without a disc in the disc compartment.
– When you play a disc placed upside-down or a defective disc.
Turning the power off
If no new operations are done within 30 seconds from the end of last operation,
the power is turned off automatically. (Auto power off function)
• You can turn off the power by pressing sSTOP/OFF/CHARGE before it is
automatically turned off.
Standby mode → F
2
3
When an operation finishes, the unit goes into standby mode until the auto power
off function automatically turns off the power.
To enter standby mode, press ePLAY/PAUSE to start playback, then press
sSTOP/OFF/CHARGE.
Adjusting the sound → G
Volume
Press + to increase the volume.
Press - to decrease the volume.
DSL
Press DSL repeatedly for more powerful sound and deeper bass.
: Deep bass is emphasized.
: Deep bass is strongly emphasized.
Press
to decrease the volume.
DSL
Press DSL repeatedly for more powerful sound and deeper bass.
: Deep bass is emphasized.
: Deep bass is strongly emphasized.
: Normal sound
I
Signal sound function
You can check the operation by beep sound when you press an operation button.
The signal sound function is activated when you purchase this unit.
To cancel the signal sound function, press ePLAY/PAUSE while pressing
PLAY MODE to display “
” while the power is off.
To resume the beep sound, repeat this procedure.
Inserting a disc → H
1 Set the dial to the OPEN position to open the disc compartment.
2 Place a disc in the center with the label side facing up.
3 Close the disc compartment tightly and set the dial to the LOCK position.
To remove the disc → I
Pick up the disc, holding its edge, while pressing the pivot gently.
Note
• The unit may not play a CD-R/RW disc that is recorded on personal computers
or some kinds of CD-R/RW recorders because of differences in recording
platforms.
• Do not attach any seal or label to either side (the recordable side or the labeled
side) of a CD-R/RW disc. It may cause malfunction.
01.3.29, 5:07 PM
XP-SR321/SR320(AU) E Page 1
J
STOP/OFF
CHARGE
3
1
Pull out the rubber cap and connect the supplied headphones to the PHONES/
LINE OUT jack.
The amplified speaker system can be connected instead to enjoy the CD sound.
1 Release HOLD.
2 Place a disc.
3 Press ePLAY/PAUSE.
Playback starts from the first track.
a track number
b elapsed playing time
c volume indicator
2
PHONES/
LINE OUT
1
PLAYBACK → J
Basic operation
To stop
To pause
2
To search for the beginning of a track
To locate a desired passage
Press sSTOP/OFF/CHARGE.
Press ePLAY/PAUSE.
To resume, press it again.
Press r or t.
Keep r or t pressed.
Release the button at the start of desired
passage.
Display during playback → K
Press ENTER/DISP during playback to change the display as follows.
1 Track display and elapsed playing time (normal display)
3
V
2 Track display and remaining playing time of the track in play
PLAY/PAUSE
V
3 Remaining number of tracks and remaining playing time
The time is not displayed in following cases.
• When trying to program tracks beyond No.32.
• When the total remaining time of the programmed tracks is over 100 minutes.
K
E•A•S•S 3× (Electronic Anti-Shock System) → L
The E•A•S•S 3× function reduces skipping or muting of the sound when the unit
is subjected to shocks.
The player keeps about 48 seconds or 12 seconds of playback sound in its
memory.
ENTER/DISP
When you start playback, the unit keeps 48 seconds in memory.
To keep 12 seconds in the memory, press E•A•S•S repeatedly until
and
appear.
To cancel the E•A•S•S 3× function, press E•A•S•S repeatedly until E•A•S•S
appears.
Note
L
• Before jogging with this unit, allow sufficient time for the memory buffer to fill up
completely (ideally about 20 seconds).
Continuous shock or vibration may cause the sound to be interrupted even if
the E•A•S•S 3× function is activated. This is normal and not a malfunction.
Should you experience an interruption in sound, stabilize the unit for a few
seconds, then resume your activity.
• When the E•A•S•S 3× function is activated, motor noise is heard as the motor
periodically rotates at high speed during playback. This is not a malfunction.
• When E•A•S•S is pressed, the unit will pause for about 2 seconds.
• When the unit is set to E•A•S•S-off or -12 second mode, the quality of the
sound will be better than E•A•S•S-48 second mode.
Resume function → M
E.A.S.S
Set the HOLD switch to RESUME.
appears, and you can start playback from the point where you stopped
playback by pressing sSTOP/OFF/CHARGE.
When the resume function is on, all-track repeat is selected automatically.
To cancel resume play, set the HOLD switch to OFF.
Note
• Resume play may start at a point about 30 seconds behind or ahead the stopped
point. Resume play may not operate if you stopped at the last 30 seconds of
the final track.
• Resume play will be canceled if you open the disc compartment. If the unit is
turned off, resume play will not be canceled. In this case, be sure to set the
HOLD switch to OFF before changing discs.
Random play → M
Press PLAY MODE while in standby mode to display
Tracks on the disc are played in random order.
.
To cancel random play, press PLAY MODE while in standby mode.
display changes to
.
M
Note
• You cannot back to previous track by pressing r during random play.
• You cannot select one-track repeat during random play.
PLAY MODE
Repeat play → M
Press PLAY MODE during playback to select repeat play as follows.
: one-track repeat B
V
: all-track repeat
PLAY MODE
Repeat play → M
Press PLAY MODE during playback to select repeat play as follows.
: one-track repeat B
V
: all-track repeat
V
no repeat play (normal play)
N
Note
1,3
STOP/OFF
CHARGE
5
2
When the unit is set to E•A•S•S-12 or -48 second mode, if PLAY MODE is pressed
at the end of the track to select the other play mode, the unit may not change to
the other mode properly.
PROGRAM PLAY → N
Up to 24 tracks can be chosen for program play.
1
1 Press ENTER/DISP while in standby mode to display “P-01”.
2 Select the desired track by pressing r and t.
a track number
b program number
3 Press ENTER/DISP within 8 seconds.
If it is not pressed within 8 seconds, the track number changes to 00. Repeat
the procedure from step 2 again.
4 Repeat steps 2 and 3 to program more tracks.
5 Press ePLAY/PAUSE to start program play.
ENTER/DISP
2
To stop program play
Press sSTOP/OFF/CHARGE.
To add tracks to the program
3
Repeat steps 2 and 3 before you proceed to step 5. You can add tracks to the
end of the program.
ENTER/DISP
To erase the program
Press sSTOP/OFF/CHARGE while in standby mode.
To check the programmed tracks
5
Press ENTER/DISP repeatedly before you proceed to step 5.
The number of each programmed track will be displayed in order of playback.
PLAY/PAUSE
Note
• The program is also erased when the disc compartment is opened or the auto
power off function turns the power off.
• When 24 tracks are programmed, “P-FULL” appears, and no more tracks may
be added.
• You cannot back to the previous track by holding r pressed during program
play.
• Repeat play and random play can be performed during program play.
XP-SR321/SR320(AU)E
2
O
RADIO RECEPTION
MONO/ST
STOP/OFF
CHARGE
1
2
Tuning in to a station → O
1 Press BAND TUNER ON repeatedly to select AM or FM.
2 Press TUNING + (t) or - (r) to tune in to a station.
After listening, press sSTOP/OFF/CHARGE to turn off the radio.
For quick tuning
Keep either TUNING + (t) or - (r) pressed for about 1 second. When a
station is tuned in to, the frequency stops automatically. However, it does not
stop if the broadcast signal is weak.
1
For better reception → P
BAND/
TUNER ON
FM: The headphone cord functions as the FM antenna. Keep it extended.
AM: Turn the unit to find the position which gives the best reception.
To listen to an FM stereo broadcasting
When a tuned in station is in stereo, ST changes to
.
When the FM stereo signal is weak and distorted, press MONO/ST. ST goes out
and the sound will be heard in monaural but distortion will be reduced.
2
Note
P
Q
• Do not open the disc compartment during radio reception. The buttons will be
deactivated.
• The power is turned off automatically if no operation is made after 5 or 6 hours
from the last operation during radio reception.
FM
AM
Changing AM steps → Q
Radio broadcasts have different frequency ranges and changes in different
steps in different countries.
This unit is factory-set to 10 kHz steps on AM. When using the unit where
the AM step changes to 9 kHz, change it as follows.
1 When the power is off, keep BAND TUNER ON pressed for 8 seconds.
“S-10” is displayed for 5 seconds.
2 While “S-10” is displayed, press PRESET CALL UP/DOWN to display
“S-9”.
3 Press ENTER/DISP within 5 seconds.
3
To resume to 10 kHz, change in the similar way.
1
2
Note
When the AM step is changed, stations that you preset are erased.
PRESETTING STATIONS
Automatic presetting → R
R
2
4
3
BAND/
TUNER ON
After listening, press sSTOP/OFF/CHARGE.
If there is a station you wish to skip during presetting
1
2
You can preset up to total of 30 stations on AM and FM.
1 Release HOLD.
2 Press BAND TUNER ON to turn on the radio.
3 Press TUNING + (t) or - (r) to exit preset mode.
4 Keep ENTER/DISP pressed for more than 5 seconds.
The unit searches for and memorizes the receivable stations.
Automatic presetting ends after 30 stations are preset.
To stop presetting before 30 stations are preset, press sSTOP/OFF/
CHARGE.
When a station is tuned in, scanning stops and the tuned station is heard for
5 seconds. Press TUNING + (t) within these 5 seconds to skip this station.
3
Note
When broadcast signals are very weak, stations cannot be preset automatically.
Preset them manually.
Manual presetting → S
4
You can preset up to total of 30 stations on AM and FM.
1 Press BAND TUNER ON repeatedly to select AM or FM.
2 Press TUNING + (t) or - (r) to tune in to a station.
3 Press ENTER/DISP to preset the station.
a Preset number
ENTER/DISP
To preset more stations, repeat steps 2 and 3.
Listening to preset stations → T
S
1 Press BAND TUNER ON repeatedly to select AM or FM.
2 Press PRESET CALL UP/DOWN repeatedly to select the preset number.
3
1
2
1
BAND/
TUNER ON
2
After listening, press sSTOP/OFF/CHARGE to turn off the radio.
Changing the presetting
1 Press PRESET CALL UP/DOWN repeatedly to select the preset number
you wish to change.
2 Keep ENTER/DISP pressed for 1 or more seconds until the preset number
and the frequency flash.
3 While the preset number is flashing, press TUNING + (t) or - (r)
to tune in to a station.
4 Press ENTER/DISP to preset the station on the selected preset number.
If the flashing stops, repeat the procedure from step 2.
Erasing the presettings one by one
to tune in to a station.
4 Press ENTER/DISP to preset the station on the selected preset number.
1
BAND/
TUNER ON
2
If the flashing stops, repeat the procedure from step 2.
Erasing the presettings one by one
Press sSTOP/OFF/CHARGE after step 2 in “Changing the presetting” above.
Each preset station is erased. All the settings move up by ones and the preset
numbers are refreshed.
3
Erasing all of the presetting
ENTER/DISP
Keep ENTER/DISP pressed, then press BAND TUNER ON when the frequency
and preset number starts flashing.
CONNECTING TO AN EXTERNAL UNIT → U
T
STOP/OFF
CHARGE
1
2
Use a commercially available connection cord which has a 3.5 ø stereo miniplug at one end and two phono plugs at the other end.
Connect the stereo mini-plug to the PHONES/LINE OUT jack of the unit and
connect the phono plugs to the analog input terminals of the external unit, such
as the amplifier or the equipment with the built-in amplifier. The CD sound can be
heard through the connected audio system.
Note
• Turn off the power of both units before connection.
• DO NOT connect to the PHONO inputs of an amplifier (with a built-in
phonoequalizer-amplifier).
• Adjust the volume and DSL on this unit.
U
R
L
LINE IN
CD IN
AUX
PHONES/
LINE OUT
01.3.29, 5:08 PM
XP-SR321/SR320(AU) E Page 2
Download PDF