Integrated Front Panel Panel Kit.qxd - Sub-Zero

Integrated Front Panel Panel Kit.qxd
W
O L F
K
I T
W
10/10/2003
A R M I N G
(802727) I
D
6:03 AM
Page 1
R A W E R
I
N T E G R A T E D
I
N S T A L L A T I O N
The Wolf Warming Drawer Model
WD30 can be installed above or
below a single wall oven SO30F/S,
SO30U/B, SO30U/P or SO30U/S or
below a cooktop CT36E/S, CT36E/B,
CT36E/P, CT36G/S, or CT36G/P.
Please refer to installation instructions
provided with cooktops for additional
installation information.
The Wolf Warming Drawer can also
be installed next to or above another
Wolf Warming Drawer.
IMPORTANT NOTE: This Front Panel Kit
is designed for and approved only for
use with Wolf Warming Drawer WD30.
• Integrated Front Panel Kit (802727)
Contains:
(1) Front Panel (802598)
(1) Condensation Trap (805553)
(2) Pem Nuts (805551)
(10) 8-18 x 3/8" Long Screws
IMPORTANT NOTE: Please read
these instructions carefully before
beginning installation. Follow all
applicable regulations and guidelines
specified in the Wolf Warming
Drawer Installation Guide that
accompanies the Wolf Warming
Drawer.
Install Warming Drawer:
IMPORTANT NOTE: There are
significant differences in the cabinet
requirements when installing a
Wolf Integrated Front with a Wolf
Warming Drawer. Overall cabinet
width and depth greatly impacted as
specifications are much different that
Warming Drawer with a Stainless Steel
front.
F
P
R O N T
A N E L
N S T R U C T I O N S
26" (660)
CABINET DEPTH
33" (838)
CABINET WIDTH
28 1/2" (724)
OVEN ROUGH
OPENING WIDTH
27 3/16"
(691)
2 3/8"
2 3/8"
(60)
(60)
4"
(102)
5"
(127)
5"
2" (51) x 2" (51)
ANTI-TIP BLOCK
10 3/8"*
10 3/8"*
(264)
(264)
25 1/2" min (648)
ROUGH OPENING DEPTH
WARMING DRAWER
4"
(127)
E
E
(102)
29 15/16"* (760)
ROUGH OPENING WIDTH
WARMING DRAWER
CABINET SIDE VIEW
NOTE: Dimensions in parentheses are in millimeters.
_ 1/8" (3 mm).
*Dimension may vary by +
Tools and Materials Required:
• Wood screws or other hardware for installing runners or shelf to support warming drawer and mount front support framing to cabinet
• 2" x 4" or 2" x 2"(51 x 102 or 51 x 51) lumber for runners
• 2" x 4" or 2" x 2"(51 x 102 or 51 x 51) wood block for anti-tip.
• Lumber for front support framing
• Decorative wood front panel
• Saw
• Level
• Drill and 1/16" bit
• Phillips screwdriver
Integrated Front Panel Panel Kit.qxd
W
O L F
P
A N E L
W
K
10/10/2003
A R M I N G
I T
I
D
6:03 AM
Page 2
R A W E R
N S T A L L A T I O N
I
I
OVEN TRIM EXTENDS 5/16" (8)
BELOW OVEN PLATFORM
3/4" (19) THICK WALL OVEN
Decorative wood front panel should
be a minimum of 1/2"(13) thick.
SUPPORT PLATFORM
2" (51) x 2" (51)
ANTI-TIP BLOCK
Follow Wolf Warming Drawer
Installation Instructions to Remove
Packaging, Electrical Requirements
and Grounding the Warming Drawer.
10 7/8"
(276)
2 3/8"
(60)
9/16"
(14)
3/4" (19) THICK
SUPPORT FRAME
9 1/4"
WARMING DRAWER
ROUGH OPENING
(235)
10 3/8"
(264)
ROUGH
OPENING
HEIGHT
3/4" (19) THICK PLATFORM
The cabinet for the warming drawer
must be:
• Depth: 26"
• Width: 33"
3/4" (19) THICK x 1 1/2" (38)
3/4" (19) THICK
PLYWOOD CLEAT
FACE PLATE
9/16"
(14)
25 1/2" min (648)
WARMING DRAWER ROUGH OPENING DEPTH
26" (660)
CABINET DEPTH
CABINET SIDE VIEW
The opening for the warmingdrawer
must be:
• Depth: 25-1/2"(648) minimum from
inside back to front of cabinet frame.
29 15/16" (760)
WARMING DRAWER ROUGH OPENING WIDTH
2 3/8"
2" (51) x 2" (51)
ANTI-TIP BLOCK
(REAR OF OPENING)
• Width: 29-15/16"(760)
3/4" (19) THICK WALL OVEN
SUPPORT PLATFORM
(60)
9/16"
(14)
3/4" (19) THICK SUPPORT FRAME
10 7/8"
(276)
• If installed under a wall oven: Allow a
2-3/8”(60) minimum between oven and
drawer cutouts for clearance of overlaps.
R O N T
N S T R U C T I O N S
Runners must be level, rigidly
mounted and capable of supporting
175 pounds (79kg).
• Height: 10-3/8"(263)
F
N T E G R A T E D
31 3/8" (979)
SUPPORT FRAME WIDTH
9 1/4"
(235)
28 1/2" (724)
SUPPORT FRAME OPENING
3/4" (19) THICK x 1 1/2" (38)
3/4" (19) THICK
PLYWOOD CLEAT
PLATFORM
10 3/8"
(264)
ROUGH
OPENING
HEIGHT
9/16"
(14)
31 1/2" (800)
33" (838)
CABINET WIDTH
• If installed above a wall oven: Allow a
CABINET FRONT VIEW
2"(51) minimum between oven and
drawer cutouts for clearance of overlaps. IMPORTANT NOTE: If you are installing the warming drawer in a frameFloor must be able to support 175
less cabinet, it may be necessary to install 1/2"(13) wide cleats to accept
pounds (79kg).
drawer mounting screws. See drawer for mounting hole locations.
Cabinet Support:
The support frame:
IMPORTANT NOTE: When installed in combination with a single oven,
• Width: 31-3/8"(797)
check to be certain that any oven supports near the cutout do not
• Height: 10-7/8”(276)
obstruct the 26" required cabinet depth of the warming drawer cutout.
• Thickness: 3/4"(19)
The support frame cut-out:
• Width: 28-1/2"(724)
• Height: 9-1/4"(235)
• A 2-3/8"(60) minimum clearance between oven and warming drawer
cutouts are required. Additional clearance may be required if 2" x 4"(51 x
102) blocks are used to support runners or solid floor of the oven above.
• The warmer drawer may be supported by either a solid bottom, 2" x 4"
or 2" x 2"(51 x 102 or 51 x 51) runners.
• The support must be level, there is no way to level the drawer once it is
installed.
• The entire weight of the drawer is supported by the runners or solid
floor and must be capable of supporting 175 pounds (79kg).
Integrated Front Panel Panel Kit.qxd
W
O L F
P
A N E L
W
K
10/10/2003
A R M I N G
I T
I
D
6:03 AM
Page 3
R A W E R
N S T A L L A T I O N
Installation Procedures:
CAUTION
Anti-tip Precautions: An
anti-tip block must be
installed to prevent the
warming drawer from
tipping forward when
opened. Failure to do so
could result in personal
injury.
Step 1:
• Install 2" x 4" or 2" x 2"(51 x 102
or 51 x 51) anti-tip block against rear
cabinet wall, measuring 9-1/4"(235)
from floor of cutout to the bottom of
the block.
• Install front support framing
around cabinet opening of 10-3/8"
(263). Framing must be a minimum
of 9-1/4"(235) opening to allow for
the warmer drawer installation.
• Front support framing must be a
minimum of 3/4"(19) thick.
• Mount front support frame
securely to cabinet.
I
N T E G R A T E D
I
F
R O N T
N S T R U C T I O N S
Step 2:
• Slide left corner of the drawer into
the opening.
• Drive wood screws provided with
the Warming Drawer into the four
holes.
• If the outlet is in an adjacent
• Install Front Panel.
cabinet, push power cord into the
hole leading to the outlet location.
• Turn power back on to wall
PLEASE NOTE: Check to be certain
receptical.
the power cord does not get trapped
under the drawer. Thread the cord
through the hole as you push back
the drawer into the opening. You
must follow all National and/or Local
Electric Code Regulations.
• Turn power off to wall receptacle.
• If the outlet is installed in the
opening, plug the cord into the
outlet. Coil the power cord and
secure the power cord to the side of
the warming drawer with the power
cord clip.
• Push the drawer back until the
front flange is flush with the front
support frame.
Door
Assembly
Front Panel
• Open the drawer fully.
• Drill pilot holes through the holes
in the overlapping frame, one on
each corner.
DOOR
ASSEMBLY
FRONT
PANEL
Integrated Front Panel Panel Kit.qxd
W
O L F
P
A N E L
W
K
10/10/2003
A R M I N G
I T
I
D
6:03 AM
Page 4
R A W E R
N S T A L L A T I O N
Install Front Panel and
Condensation Trap:
1. Remove two mounting nuts from
Wolf Warming Drawer door front
and discard nuts and lockwashers.
DO NOT DISCARD Warming
Drawer vent spacer.
I
F
N T E G R A T E D
I
R O N T
N S T R U C T I O N S
TWO NUTS AND
WASHERS
WARMING DRAWER
VENT SPACER
DOOR FRONT
ASSEMBLY
2. Align condensation trap with
mounting holes on Warming
Drawer door front. Install condensation trap over vent spacer with
pem nuts supplied. Make sure that
spacer slots align with drawer slots
for proper ventilation.
3. Make sure that Warming Drawer
Moisture Select Lever located on
inside of door front moves freely.
If Moisture Select Lever does not
move freely, readjust pem nuts
used to install condensation trap.
4. Install integrated front panel by
sliding top lip of front panel over
Warming Drawer door front.
DOOR FRONT
PANEL
PEM NUT
PEM NUT
CONDENSATION
TRAP
DOOR FRONT
ASSEMBLY
5. Insert three (3) screws in top of
front panel lip through door frame
assembly. Use screwdriver to
tighten screws.
6. Insert three (3) screws in bottom
of front panel through door frame
assembly. Use screwdriver to tighten
screws.
804630 REV-A
10/03