Hikvision DS-KD-TDM Touch & Display Modul Owner's Manual

Video Intercom Module Door
Station
User Manual
Video Intercom Module Door Station User Manual
Legal Information
©2021 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved.
About this Manual
The Manual includes instructions for using and managing the Product.
Pictures, charts, images and all other information hereinafter are for
description and explanation only. The information contained in the Manual
is subject to change, without notice, due to firmware updates or other
reasons. Please find the latest version of this Manual at the Hikvision
website ( https://www.hikvision.com/ ).
Please use this Manual with the guidance and assistance of professionals
trained in supporting the Product.
Trademarks
and other Hikvision's trademarks and logos are the
properties of Hikvision in various jurisdictions.
Other trademarks and logos mentioned are the properties of their
respective owners.
Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL
AND THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND
FIRMWARE, ARE PROVIDED "AS IS" AND "WITH ALL FAULTS AND ERRORS".
HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR
FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS
AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR
ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES,
INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS,
BUSINESS INTERRUPTION, OR LOSS OF DATA, CORRUPTION OF SYSTEMS, OR
LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH OF CONTRACT,
TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN
i
Video Intercom Module Door Station User Manual
CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS.
YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET PROVIDES FOR
INHERENT SECURITY RISKS, AND HIKVISION SHALL NOT TAKE ANY
RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR
OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS
INFECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION
WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE
LAWS, AND YOU ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE
CONFORMS TO THE APPLICABLE LAW. ESPECIALLY, YOU ARE RESPONSIBLE,
FOR USING THIS PRODUCT IN A MANNER THAT DOES NOT INFRINGE ON THE
RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF
PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND
OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY
PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION
OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR
PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN
THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR
FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE
APPLICABLE LAW, THE LATTER PREVAILS.
ii
Video Intercom Module Door Station User Manual
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Symbol
Danger
Caution
Note
Description
Indicates a hazardous situation which, if not avoided, will or
could result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, could result in equipment damage, data loss,
performance degradation, or unexpected results.
Provides additional information to emphasize or
supplement important points of the main text.
iii
Video Intercom Module Door Station User Manual
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved
by the party responsible for compliance could void the user's authority to
operate the equipment.
FCC compliance: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference
that may cause undesired operation.
iv
Video Intercom Module Door Station User Manual
EU Conformity Statement
This product and - if applicable - the supplied accessories too are
marked with "CE" and comply therefore with the applicable
harmonized European standards listed under the EMC Directive
2014/30/EU, the RoHS Directive 2011/65/EU
2012/19/EU (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the
European Union. For proper recycling, return this product to your
local supplier upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more information
see: www.recyclethis.info
2006/66/EC (battery directive): This product contains a battery
that cannot be disposed of as unsorted municipal waste in the
European Union. See the product documentation for specific
battery information. The battery is marked with this symbol,
which may include lettering to indicate cadmium (Cd), lead (Pb),
or mercury (Hg). For proper recycling, return the battery to your
supplier or to a designated collection point. For more information
see:www.recyclethis.info
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
1. this device may not cause interference, and
2. this device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radioexempts de licence. L'exploitation est autorisée aux deux
conditions suivantes :
v
Video Intercom Module Door Station User Manual
1. l'appareil ne doit pas produire de brouillage, et
2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser) gain approved for the
transmitter by Industry Canada. To reduce potential radio interference to
other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur
radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou
inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de
réduire les risques de brouillage radioélectrique à l'intention des autres
utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la
puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité
nécessaire à l'établissement d'une communication satisfaisante.
This equipment should be installed and operated with a minimum distance
20cm between the radiator and your body.
Cet équipement doit être installé et utilisé à une distance minimale de 20
cm entre le radiateur et votre corps.
vi
Video Intercom Module Door Station User Manual
Contents
1 Appearance ................................................................................................ 1
2 Terminal and Wiring ................................................................................... 9
2.1 Terminal Description ......................................................................................... 9
2.2 Module Door Station Wiring ........................................................................... 13
2.2.1 Door Lock Wiring .................................................................................... 13
2.2.2 Door Contact Wiring ............................................................................... 14
2.2.3 Exit Button Wiring .................................................................................. 14
2.2.4 RS-485 Card Reader Wiring .................................................................... 15
3 Installation ................................................................................................ 16
3.1 Configure Sub Module Address ....................................................................... 16
3.2 One-Module Installation ................................................................................. 17
3.2.1 One-Module Surface Mounting .............................................................. 17
3.2.2 One-Module Flush Mounting ................................................................. 20
3.3 Two-Module Installation ................................................................................. 25
3.3.1 Two-Module Surface Mounting .............................................................. 25
3.3.2 Two-Module Flush Mounting ................................................................. 29
3.4 Three-Module Installation .............................................................................. 33
3.4.1 Three-Module Surface Installation ......................................................... 33
3.4.2 Three-Module Flush Mounting ............................................................... 37
3.5 More-Than-Three Module Installation ............................................................ 41
3.5.1 More-than-Three Module Surface Mounting ......................................... 41
3.5.2 More-Than-Three Module Flush Mounting ............................................ 47
vii
Video Intercom Module Door Station User Manual
4 Activation ................................................................................................. 55
4.1 Activate Device via Client Software ................................................................. 55
4.2 Edit Network Parameters ................................................................................ 55
5 Configuration via Client Software ............................................................. 57
5.1 Device Management ....................................................................................... 57
5.1.1 Add Online Device .................................................................................. 57
5.1.2 Add Device by IP Address ....................................................................... 58
5.1.3 Add Device by IP Segment ...................................................................... 58
5.2 Live View via Door Station .............................................................................. 59
5.3 Remote Configuration ..................................................................................... 59
5.3.1 Device Management .............................................................................. 59
5.3.2 Local Parameters Settings ....................................................................... 61
5.3.3 System Settings ....................................................................................... 62
5.3.4 Network Settings .................................................................................... 65
5.3.5 Video & Audio Settings ........................................................................... 70
5.3.6 Image Settings ........................................................................................ 72
5.3.7 Schedule Settings .................................................................................... 75
5.3.8 Intercom Settings .................................................................................... 76
5.3.9 Access Control Settings ........................................................................... 81
5.4 Organization Management ............................................................................. 85
5.4.1 Add Organization .................................................................................... 85
5.4.2 Modify and Delete Organization ............................................................. 85
5.5 Person Management ....................................................................................... 85
5.5.1 Add Person ............................................................................................. 86
viii
Video Intercom Module Door Station User Manual
5.5.2 Modify and Delete Person ...................................................................... 87
5.5.3 Import and Export Person Information .................................................. 87
5.5.4 Get Person Information from Device ...................................................... 88
5.5.5 Change Person to Other Organization .................................................... 88
5.5.6 Issue Card in Batch ................................................................................. 89
5.5.7 Permission Settings ................................................................................. 90
6 Video Intercom Operation ........................................................................ 92
6.1 Video Intercom Operation via Device ............................................................. 92
6.1.1 Call Resident ........................................................................................... 92
6.1.2 Issue Card ............................................................................................... 93
6.1.3 Unlock Door ............................................................................................ 94
6.2 Video Intercom Operation via Client Software ............................................... 95
6.2.1 Receive Call from Door Station ............................................................... 95
6.2.2 Live View via Door Station ...................................................................... 97
6.2.3 View Call Logs ......................................................................................... 97
6.2.4 Search Video Intercom Information ....................................................... 97
A. Relevant Instructions for External Power Supply and Wiring of 2-wire
Video Intercom Products (2020-1-20) ....................................................... 101
B. Communication Matrix and Device Command ..................................... 106
ix
Video Intercom Module Door Station User Manual
1 Appearance
Main Unit
Figure 1-1 Main Unit Appearance
Table 1-1 Appearance Description
No.
Description
1
Microphone
2
Low Illumination IR Supplement Light
3
Built-in Camera
4
Loudspeaker
5
Call Button
6
Nametag
7
TAMPER
8
Network Interface
9
Module-​Connecting Interface (output)
10
Terminals
1
Video Intercom Module Door Station User Manual
Note
Nametag area supports insert customized name card. The suggested card
size is: 58 (L) x 11.7(W) mm.
●
The module connecting interface is used to connect other function
module, such as nametag module, keypad module, card reader module,
etc. All these modules are known as sub module.
●
Two-Wire Main Unit
Figure 1-2 Two-Wire Main Unit
Table 1-2 Appearance Description
No.
Description
1
Microphone
2
Low Illumination IR Supplement Light
3
Built-in Camera
4
Loudspeaker
5
Call Button
6
Nametag
7
TAMPER
8
Two-Wire Interface
2
Video Intercom Module Door Station User Manual
No.
Description
9
Module-​Connecting Interface (output)
10
Terminals
Note
Nametag area supports insert customized name card. The suggested card
size is: 58 (L) x 11.7(W) mm.
●
The module connecting interface is used to connect other function
module, such as nametag module, keypad module, card reader module,
etc. All these modules are known as sub module.
●
Nametag Module
Figure 1-3 Nametag Module Appearance
Table 1-3 Appearance Description
No.
Description
1
Call Button
2
Nametag
3
Module-​Connecting Interface (output)
4
Module-​Connecting Interface (input)
5
Debugging Port
3
Video Intercom Module Door Station User Manual
Keypad Module
Figure 1-4 Keypad Module Appearance
Table 1-4 Appearance Description
No.
Description
1
Button
2
Module-​Connecting Interface (output)
3
Module-​Connecting Interface (input)
4
Debugging Port
Indicator Module
Figure 1-5 Indicator Module
4
Video Intercom Module Door Station User Manual
Table 1-5 Appearance Description
No.
Description
1
Calling Indicator
2
Two-way Audio Indicator
3
Unlock Indicator
4
Module-​connecting Interface (output)
5
Module-​connecting Interface(input)
6
Debugging Port
Card Reader Module
Figure 1-6 Card Reader Module
Table 1-6 Appearance Description
No.
Description
1
Card Reading Area
2
Module-​connecting Interface (output)
3
Module-​connecting Interface(input)
4
Debugging Port
5
Video Intercom Module Door Station User Manual
Display Module
Figure 1-7 Display Module
Table 1-7 Description
No.
Description
No.
Description
1
Screen
5
Back Button
2
Up Button
6
Module-​connecting
Interface (output)
3
Down Button
7
Module-​connecting
Interface (input)
4
Confirm Button
8
Debug Port
6
Video Intercom Module Door Station User Manual
Information Module
Figure 1-8 Information Module
Table 1-8 Description
No.
Description
1
Display Area
2
Module-​connecting Interface (output)
3
Module-​connecting Interface (input)
4
Debugging Port
Touch-Display Module
Figure 1-9 Touch-Display Module
7
Video Intercom Module Door Station User Manual
Table 1-9 Description
No.
Description
1
Touch-Display Area
2
TF Card Slot
3
Module-​connecting Interface (output)
4
Module-​connecting Interface (input)
5
Video & Audio Terminal
6
Debugging Port
Note
The debugging port is used for debugging only.
8
Video Intercom Module Door Station User Manual
2 Terminal and Wiring
2.1 Terminal Description
Main Unit Terminals
Figure 2-1 Main Unit Terminals
Table 2-1 Descriptions of Terminals and Interfaces
No.
Interface
Description
A1
NC1
Door Lock Relay Output (NC)
A2
NO1
Door Lock Relay Output (NO)
A3
COM
Common Interface
A4
NC2
Door Lock Relay Output (NC)
A5
NO2
Door Lock Relay Output (NO)
A6
GND
Grounding
A7
12 VDC
Power Input
A8
GND
Grounding
B1
AIN2
For the access of Door Magnetic 2
B2
AIN1
For the access of Door Magnetic 1
9
Video Intercom Module Door Station User Manual
No.
Interface
Description
B3
AIN3
For the access of Exit Button 1
B4
AIN4
For the access of Exit Button 2
B5
485-
Module-​connecting Interface
B6
485+
B7
12 V OUT
B8
GND
C
LAN
PoE Network Interface(Supports IEEE
802.3af/at-Compliant Devices)
Two-Wire Main Unit Terminal
Figure 2-2 Two-Wire Main Unit Terminal
Table 2-2 Descriptions of Terminals and Interfaces
No.
Interface
Description
A1
NC1
Door Lock Relay Output (NC)
A2
NO1
Door Lock Relay Output (NO)
A3
COM
Common Interface
A4
NC2
Door Lock Relay Output (NC)
10
Video Intercom Module Door Station User Manual
No.
Interface
Description
A5
NO2
Door Lock Relay Output (NO)
A6
GND
Grounding
A7
12 VDC
Reserved
A8
GND
Grounding
B1
AIN2
For the access of Door Magnetic 2
B2
AIN1
For the access of Door Magnetic 1
B3
AIN3
For the access of Exit Button 1
B4
AIN4
For the access of Exit Button 2
B5
485-
Module-​connecting Interface
B6
485+
B7
12 V OUT
B8
GND
C
Two-Wire Interface
Two-Wire Interface
Sub Module Terminal (Except Touch-Display Module)
Figure 2-3 Sub Module Terminal (Except Touch-Display Module)
11
Video Intercom Module Door Station User Manual
Table 2-3 Description
No.
Interface
Description
A1
485-
Module-​Connecting Interface (Input)
A2
485+
A3
12V IN
A4
GND
B1
485-
B2
485+
B3
12V OUT
B4
GND
Module-​Connecting Interface (Output)
Touch-Display Module
Figure 2-4 Touch-Display Module
Table 2-4 Description
No.
Interface
Description
A1
485-
Module-​Connecting Interface (Input)
A2
485+
A3
12V IN
12
Video Intercom Module Door Station User Manual
No.
Interface
Description
A4
GND
B1
485-
B2
485+
B3
12V OUT
B4
GND
C1
GND
Grounding Interface
C2
CVSB IN
Composite Video Broadcast Signal Input
(Reserved)
C3
LINEOUT-
Audio Output (Reserved)
C4
LINEOUT+
Module-​Connecting Interface (Output)
2.2 Module Door Station Wiring
2.2.1 Door Lock Wiring
Figure 2-5 Door Lock Wiring
13
Video Intercom Module Door Station User Manual
Note
Terminal NC1/COM is set as default for accessing magnetic lock/electric bolt;
terminal NO2/COM is set as default for accessing electric strike.
2.2.2 Door Contact Wiring
Figure 2-6 Door Contact Wiring
Note
AIN1 and AIN2 are defaulted to connect door contact. Door contact connected to
AIN1 detects status of the lock that connected to NC1/NO1; Door contact connected
to AIN2 detects the status of the lock connected to NC2/NO2.
2.2.3 Exit Button Wiring
14
Video Intercom Module Door Station User Manual
Figure 2-7 Exit Button Wiring
Note
AIN3 and AIN4 are set as default for connecting exit button. Exit button connected to
AIN3 opens the lock connected to NC1/NO1; Exit button connected to AIN4 controls
the lock that connected to NC2/NO2.
2.2.4 RS-485 Card Reader Wiring
To connect RS-485 card reader, refer to the picture below.
Figure 2-8 RS-485 Card Reader Wiring
15
Video Intercom Module Door Station User Manual
3 Installation
Note
●
Make sure the device in the package is in good condition and all the assembly
parts are included.
●
Sub module must work along with the main unit.
●
Set the sub module address before start the installation steps.
●
Make sure the place for surface mounting is flat.
●
Make sure all the related equipment is power-off during the installation.
●
Tools that you need to prepare for installation:
Drill (ø6), cross screwdriver (PH1*150 mm), and gradienter.
3.1 Configure Sub Module Address
You need to set the sub module address via DIP switch before installation.
Steps
1. Remove the rubber cover on the rear panel of the sub module to expose the DIP
switch.
Figure 3-1 DIP Switch
2. Set the sub module address according to the DIP rules, and install the rubber
cover back.
16
Video Intercom Module Door Station User Manual
Note
●
●
Bit 1, 2, 3, 4 are used to coding the sub module address. Bit 5, 6, 7 are reserved.
Set Bit 8 as on to enable a resistance (120Ω).
Valid sub module address is from 1 to 8. The address should be unique for
connecting to the main unit.
The sub module address and its corresponding switch status are displayed as
below.
Table 3-1 Description
Sub
1
Module
Address
2
3
4
5
6
7
8
Bit 1
ON
OFF
ON
OFF
ON
OFF
ON
OFF
Bit 2
OFF
ON
ON
OFF
OFF
ON
ON
OFF
Bit 3
OFF
OFF
OFF
ON
ON
ON
ON
OFF
Bit 4
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
3.2 One-Module Installation
3.2.1 One-Module Surface Mounting
17
Video Intercom Module Door Station User Manual
Before You Start
Figure 3-2 Mounting Frame
Note
●
●
The dimension of one module mounting frame (W × H × D) is: 117 mm × 107 mm
× 32.7 mm.
The dimensions above are for reference only. The actual size can be slightly
different from the theoretical dimension.
Steps
1. Paste the installation Sticker 1 onto the wall. Make sure the sticker is placed
horizontally via measuring with the gradienter.
2. Drill 4 holes according to the screw holes on the sticker.
Note
●
The suggested size of hole is 6 (diameter) × 25 (depth) mm.
●
The suggested length of cables left outside is 100 mm.
18
Video Intercom Module Door Station User Manual
Figure 3-3 Drill Screw Holes
3. Remove the stricker and insert the expansion sleeves into the screw holes.
4. Fix the mounting frame onto the wall with 4 expansion bolts.
Figure 3-4 Fix the Mounting Frame
19
Video Intercom Module Door Station User Manual
5. Connect the cables to the corresponding interfaces of the main unit and insert the
main unit into the frame.
Figure 3-5 Insert the Main Unit
6. Fix the cover onto the frame.
Figure 3-6 Fix the Cover
3.2.2 One-Module Flush Mounting
20
Video Intercom Module Door Station User Manual
Before You Start
Figure 3-7 Front and Side View of the Gang Box
Figure 3-8 Gang Box
21
Video Intercom Module Door Station User Manual
Note
The dimension of one-module gang box is: 115 (W) × 134 (H) × 56 (D) mm. The
dimension is for reference only.
Steps
1. Drill an installation hole, and pull the cables out.
Note
●
●
The suggested dimension of installation hole is 118 (W) × 108 (H) × 45.5 (D)
mm.
The suggested length of cables left outside is 100 mm.
Figure 3-9 Drill Installation Hole
2. Remove the plastic sheet of the cable entry.
3. Mark the gang box screw holes on the wall.
1) Route the cables through the gang box hole.
2) Insert the gang box into the installation hole.
3) Mark the gang box screw holes' position with a marker, and take out the gang
box.
22
Video Intercom Module Door Station User Manual
Figure 3-10 Mark the Screw Holes
4. Drill 4 holes according to marks on the wall, and insert the expansion sleeves into
the screw holes.
Note
The suggested size of the hole is 6 (diameter) × 45 (depth) mm.
5. Route the cables through the gang box hole. Insert the gang box into the
installation hole. Fix the gang box with 4 expansion bolts.
Figure 3-11 Fix the Gang Box
6. Fill the gap between the gang box and the wall with concrete. Remove the 4
mounting ears with tool after concrete is dry.
23
Video Intercom Module Door Station User Manual
Figure 3-12 Remove the Mounting Ears
7. Connect the cables to the corresponding interfaces of the main unit and insert the
unit into the gang box.
Figure 3-13 Insert the Main Unit
8. Fix the cover and the main unit with 2 socket head cap screws by using a hexagon
wrench (supplied).
24
Video Intercom Module Door Station User Manual
Figure 3-14 Fix the Cover
3.3 Two-Module Installation
3.3.1 Two-Module Surface Mounting
Before You Start
Figure 3-15 Mounting Frame
25
Video Intercom Module Door Station User Manual
Note
●
●
The dimension of two-module mounting frame (W × H × D) is: 219 mm × 107 mm
× 32.7 mm.
The dimensions above are for reference only. The actual size can be slightly
different from the theoretical dimension.
Steps
1. Paste the installation Sticker 1 onto the wall. Make sure the sticker is placed
horizontally via measuring with the gradienter.
2. Drill 4 holes according to the screw holes on the sticker. The suggested size of hole
is 6 (diameter) × 25 (depth) mm. The suggested length of cables left outside is 270
mm.
Figure 3-16 Drill Screw Holes
3. Remove the sticker and insert the expansion sleeves into the screw holes.
4. Fix the mounting frame onto the wall with 4 expansion bolts.
26
Video Intercom Module Door Station User Manual
Figure 3-17 Fix the Mounting Frame
5. Thread the module-connecting line across the thread hole of the frame. Pass the
main unit connecting lines across the thread hole to the upper grid.
Figure 3-18 Placement of Lines
6. Connect the cables.
1) Connect the lines and module-connecting line to the corresponding interfaces
of the main unit, then place the main unit into the upper grid.
2) Connect the other end of the module-connecting line to the input interface of
the sub module.
27
Video Intercom Module Door Station User Manual
3) Organize the cable with cable tie in the package. The suggested cable
connection picture as shown below.
Figure 3-19 Line Connection Effect Picture
7. Insert the modules into the frame after wiring. The main unit must be placed in
the top grid.
Figure 3-20 Insert the Modules
8. Use the hexagon wrench in the package to fix the cover onto the frame.
28
Video Intercom Module Door Station User Manual
Figure 3-21 Fix the Cover
3.3.2 Two-Module Flush Mounting
Before You Start
Figure 3-22 Gang Box
29
Video Intercom Module Door Station User Manual
Note
The dimension of two-module gang box is: 237 (W) × 134 (H) × 56 (D) mm. The
dimension is for reference only.
Steps
1. Drill the installation hole, and pull the cable out.
Note
●
●
The suggested dimension of installation hole is 220 (W) × 108 (H) × 45.5 (D)
mm.
The suggested length of cables left outside is 270 mm.
Figure 3-23 Drill the Installation Hole
2. Select a cable entry and remove the plastic sheet.
3. Mark the gang box screw holes on the hole.
1) Routs the cables through the gang box hole.
2) Insert the gang box into the installation hole.
3) Mark the gang box screw holes' position with a marker, and take out the gang
box.
30
Video Intercom Module Door Station User Manual
Figure 3-24 Mark the Screw Holes
4. Drill 4 holes according to the marks on the wall, and insert the expansion sleeves
into the screw holes. The suggested size of hole is 6 (diameter) × 45 (depth) mm.
5. Fix the gang box with 4 expansion bolts.
Figure 3-25 Fix the Gang Box
6. Fill the gap between the gang box and the wall with concrete. Remove the
mounting ears with tool after concrete is dry.
31
Video Intercom Module Door Station User Manual
Figure 3-26 Remove the Mounting Ears
7. Connect cables and insert the modules.
1) Connect Cable 1 and one end of Cable 2 to the corresponding interfaces of the
main unit, then insert the main unit into the upper grid.
2) Connect the other end of Cable 2 to the input interface of the sub module.
Insert it into the lower grid.
Figure 3-27 Connect Cables and Insert the Modules
32
Video Intercom Module Door Station User Manual
Note
Cable 1 refers to the cables pulled out from the wall that connected to the main
unit. Cable 2 refers to the module-connecting line in the accessory package.
8. Fix the cover with 2 socket head cap screws by using a hexagon wrench (supplied).
Figure 3-28 Fix the Cover
3.4 Three-Module Installation
3.4.1 Three-Module Surface Installation
Before You Start
Figure 3-29 Mounting Frame
33
Video Intercom Module Door Station User Manual
Note
●
●
The dimension of two-module mounting frame (W × H × D) is: 320.8 mm × 107
mm × 32.7 mm.
The dimensions above are for reference only. The actual size can be slightly
different from the theoretical dimension.
Steps
1. Paste the installation sticker 1 onto the wall. Make sure the sticker is placed
horizontally via measuring with the gradienter.
2. Drill 4 holes according to the screw holes on the sticker.The suggested size of hole
is 6 (diameter) × 25 (depth) mm. The suggested length of cables left outside is 270
mm.
Figure 3-30 Drill Screw Holes
3. Remove the sticker and insert the expansion sleeves into the screw holes.
4. Fix the mounting frame onto the wall with 4 expansion bolts.
34
Video Intercom Module Door Station User Manual
Figure 3-31 Fix the Mounting Frame
Note
The mounting frame should be placed exactly as shown below for this step. The
tamper plate should be at the low right of the first grid.
Figure 3-32 Mounting Frame
5. Thread the module-connecting line across the thread holes of the frame. Pass the
main unit connecting line across the thread hole to the top grid.
35
Video Intercom Module Door Station User Manual
Figure 3-33 Placement of Lines
6. Connect the cables.
1) Connect the lines and module-connecting line 1 to the corresponding interfaces
of the main unit, then place the main unit into the upper grid.
2) Connect the other end of the module-connecting line 1 to the input interface of
the sub module. Connect two sub modules via module-connecting line 2.
3) Organize the cables with cable tie in the package. The suggested cable
connection picture as shown below.
Figure 3-34 Line Connection Effect Picture
7. Insert the modules into the frame after wiring. The main unit must be placed in
the top grid.
36
Video Intercom Module Door Station User Manual
Figure 3-35 Insert the Modules into the Frame
8. Use the hexagon wrench in the package to fix the cover onto the frame.
Figure 3-36 Fix the Cover
3.4.2 Three-Module Flush Mounting
37
Video Intercom Module Door Station User Manual
Before You Start
Figure 3-37 Gang Box
Note
●
●
The dimension of one-module gang box is: 338.8(W)×134(H)×56(D) mm.
The dimensions above are for reference only. The actual size can be slightly
different from the theoretical dimension.
Steps
1. Cave the installation hole, and pull the cable out.The suggested dimension of
installation hole is 321.8(W)×108(H)×45.5(D) mm. The suggested length of cables
left outside is 270 mm.
38
Video Intercom Module Door Station User Manual
Figure 3-38 Cave the Installation Hole
2. Select a cable entry and remove the plastic sheet.
3. Mark the gang box screw holes on the wall.
1) Route the cables through the gang box hole.
2) Insert the gang box into the installation hole.
3) Mark the gang box screw holes' position with a marker, and take out the gang
box.
Figure 3-39 Mark the Screw Holes
4. Drill 4 holes according to marks on the wall, and insert the expansion sleeves into
the screw holes. The suggested size of hole is 6 (diameter) × 45 (depth) mm.
5. Fix the gang box with 4 expansion bolts.
39
Video Intercom Module Door Station User Manual
Figure 3-40 Fix the Gang Box
6. Fill the gap between the gang box and wall with concrete. Remove the mounting
ears with tool after concrete is dry.
Figure 3-41 Remove the Mounting Ears
7. Connect cables and insert the modules.
1) Connect Cable 1 and one end of Cable 2 to the corresponding interfaces of the
main unit, then insert the main unit into the upper grid.
2) Connect the other end of Cable 2 to the input interface of Sub Module 1.
Connect one end of Cable 3 to the output interface of Sub Module 1 and insert
it into the middle grid.
3) Connect the other end of Cable 3 to the input interface of Sub Module 2. Insert
it into the bottom grid.
40
Video Intercom Module Door Station User Manual
Figure 3-42 Connect Cables and Insert Modules
Note
Cable 1 refers to the cables pulled out from the wall that connected to the main
unit. Cable 2 and Cable 3 refer to the module-connecting line in the accessory
package.
8. Fix the cover and the main unit with 2 socket head cap screws by using a hexagon
wrench (supplied).
Figure 3-43 Fix the Cover
3.5 More-Than-Three Module Installation
3.5.1 More-than-Three Module Surface Mounting
41
Video Intercom Module Door Station User Manual
Before You Start
Figure 3-44 Mounting Frame
Note
●
●
It takes two three-module mounting frames. The dimension of three-module
mounting frame (W × H × D) is: 320.8 mm × 107 mm × 32.7 mm.
The dimensions above are for reference only. The actual size can be slightly
different from the theoretical dimension.
Steps
1. Paste two Sticker 1 onto the wall. Make sure the stickers are placed horizontally
via measuring with the gradienter.
2. Drill 8 holes according to the screw holes on the sticker.
Note
●
The suggested size of hole is 6 (diameter) × 25 (depth) mm.
●
The suggested length of cables left outside is 270 mm.
3. Pull out the cable through the cable hole of the left sticker.
42
Video Intercom Module Door Station User Manual
Figure 3-45 Drill Screw Holes
4. Remove the stickers and insert the expansion sleeves into the screw holes.
5. Thread the module-connecting line (400 mm) and grounding line across the
thread hole of both frames.
Figure 3-46 Place the Grounding Line and Module-Connecting Line
43
Video Intercom Module Door Station User Manual
Note
●
There are 6 module-connecting lines in the package: 190 mm × 4 and 400 mm ×
2.
●
Take the 400 mm module-connecting line for this step.
●
The green-yellow line in the package is for grounding.
6. Fix the mounting frame onto the wall with 8 expansion bolts.
Figure 3-47 Fix the Mounting Frame
7. Pass the main unit connecting line across the thread hole to the top grid of the left
frame. Thread the module-connecting line (190 mm) across the thread hole of the
frame. The lines should be placed as shown below.
Figure 3-48 Placement of Lines
44
Video Intercom Module Door Station User Manual
8. Connect the cables.
1) Connect the cables from the wall and module-connecting line 1 to the
corresponding interfaces of the main unit, then place the main unit into the
upper grid.
2) Connect the other end of the module-connecting line 1 to the input interface of
the sub module. Connect all sub modules via module-connecting lines.
3) Organize the cable with cable tie in the package. The suggested cable
connection picture as shown below.
Figure 3-49 Line Connection Effect Picture
45
Video Intercom Module Door Station User Manual
9. Insert the modules into the frame after wiring. The main unit must be placed in
the top grid on the left.
Figure 3-50 Insert the Modules
10. Pull the grounding line out and fixed its two end to the screw on the cover.
Figure 3-51 Connect the Grounding Line to the Cover
11. Use the hexagon wrench in the package to fix the cover onto the frame.
46
Video Intercom Module Door Station User Manual
Figure 3-52 Fix the Cover
3.5.2 More-Than-Three Module Flush Mounting
47
Video Intercom Module Door Station User Manual
Before You Start
Figure 3-53 Gang Box
Note
It takes two three-module gang boxes. The dimension of the gang box is: 338.8 (W) ×
134 (H) × 56 (D) mm. The dimension is for reference only.
48
Video Intercom Module Door Station User Manual
Steps
1. Drill the installation hole, and pull the cable out.The suggested dimension of
installation hole is 321.8 (W) × 315 (H) × 45.5 (D) mm. The suggested length of
cables left outside is 270 mm.
Figure 3-54 Cave the Installation Hole
2. Connect two gang boxes as below.
Figure 3-55 Connect Two Gang Boxes
3. Select a cable entry and remove the plastic sheet.
49
Video Intercom Module Door Station User Manual
4. Remove the plastic sheets on the side of the gang boxes (shown as 1 and 2)
below:
Figure 3-56 Remove the Plastic Sheets
5. Mark the gang box screw holes on the wall.
1) Route the cables through the gang box hole.
2) Insert the gang box into the installation hole.
3) Mark the gang box screw holes' position with a marker, and take out the gang
box.
Figure 3-57 Mark the Screw Holes
50
Video Intercom Module Door Station User Manual
6. Drill 8 holes according to the marks on the wall, and insert the expansion sleeves
into the screw holes. The suggested size of hole is 6 (diameter) × 45 (depth) mm.
7. Fix the gang boxes with 8 expansion bolts.
Figure 3-58 Fix the Gang Boxes
8. Fill the gap between the gang box and wall with concrete. Remove the mounting
ears with tool after concrete is dry. Route the grounding line through the cable
entries.
Figure 3-59 Remove the Mounting Ears
Note
The green-yellow line in the package is for grounding.
9. Connect cables and insert the modules.
51
Video Intercom Module Door Station User Manual
1) Connect Cable 1 and one end of Cable 2 to the corresponding interfaces of the
Main Unit, then place the Main Unit into the upper grid of the left gang box.
2) Connect the other end of Cable 2 to the input interface of Sub Module 1.
Connect one end of Cable 3 to the output interface of Sub Module 1 and insert
it into the middle grid of the left gang box.
3) Finish the wiring and inserting according to the cable number and the position
shown as below.
Figure 3-60 Install Mounting Frame
The cables connect to each module shown as below.
Figure 3-61 Cables Connection
52
Video Intercom Module Door Station User Manual
Note
●
Cable 2,3,5 and 6 are the module-connecting lines (190 mm) in the package.
●
Cable 4 is the module-connecting line (400 mm) in the package.
●
Main unit must be put in the top grid.
10. Pull the grounding line out and fixed its two end to the screw on the cover.
Figure 3-62 Connect the Grounding Line to the Cover
11. Fix the cover with 2 socket head cap screws by using a hexagon wrench
(supplied).
53
Video Intercom Module Door Station User Manual
Figure 3-63 Fix the Cover
54
Video Intercom Module Door Station User Manual
4 Activation
4.1 Activate Device via Client Software
You can only configure and operate the door station after creating a password for
the device activation.
Default parameters of door station are as follows:
●
Default IP Address: 192.0.0.65.
●
Default Port No.: 8000.
●
Default User Name: admin.
Steps
1. Run the client software, click Maintenance and Management → Device
Management → Device to enter the page.
2. Click Online Device.
3. Select an inactivated device and click Activate.
4. Create a password, and confirm the password.
Note
We highly recommend you to create a strong password of your own choosing
(using a minimum of 8 characters, including at least three kinds of following
categories: upper case letters, lower case letters, numbers, and special characters)
in order to increase the security of your product. And we recommend you change
your password regularly, especially in the high security system, changing the
password monthly or weekly can better protect your product.
5. Click OK to activate the device.
Note
●
●
When the device is not activated, the basic operation and remote operation of
device cannot be performed.
You can hold the Ctrl or Shift key to select multiple devices in the online
devices, and click the Activate button to activate devices in batch.
4.2 Edit Network Parameters
55
Video Intercom Module Door Station User Manual
To operate and configure the device via LAN (Local Area Network), you need connect
the device in the same subnet with your PC. You can edit network parameters via
iVMS-4200 client software.
Steps
1. Select an online activated device and click the Modify Netinfo.
2. Edit the device IP address and gateway address to the same subnet with your
computer.
3. Enter the password and click OK to save the network parameters modification.
Note
●
●
●
The default port No. is 8000.
The default IP address of the door station is 192.0.0.65.
After editing the network parameters of device, you should add the devices to
the device list again.
56
Video Intercom Module Door Station User Manual
5 Configuration via Client Software
5.1 Device Management
Device management includes device activation, adding device, editing device, and
deleting device, and so on.
After running the iVMS-4200, video intercom devices should be added to the client
software for remote configuration and management.
5.1.1 Add Online Device
Before You Start
Make sure the device to be added is in the same subnet with your computer.
Otherwise, please edit network parameters first.
Steps
1. Click Online Device to select an active online device.
2. Click Add.
3. Enter corresponding information, and click Add.
57
Video Intercom Module Door Station User Manual
Figure 5-1 Add to the Client
5.1.2 Add Device by IP Address
Steps
1. Click +Add to pop up the adding devices dialog box.
2. Select IP/Domain as Adding Mode.
3. Enter corresponding information.
4. Click Add.
5.1.3 Add Device by IP Segment
58
Video Intercom Module Door Station User Manual
You can add many devices at once whose IP addresses are among the IP segment.
Steps
1. Click +Add to pop up the dialog box.
2. Select IP Segment as Adding Mode.
3. Enter corresponding information, and click Add.
5.2 Live View via Door Station
Steps
1. On the main page of the client software, click Main View to enter the Live View
page.
2. In the left list of the window, double-click the device IP or click the play icon to live
view.
3. Optional: On the Live View page, control-click and select Capture to get the
picture of the live view.
5.3 Remote Configuration
Click
to set the parameters of the device.
Note
Run the browser, click
Mode.
→ Internet Options → Security to disable the Protected
5.3.1 Device Management
You can manage the linked device on the page.
Click Device Management to enter the settings page.
59
Video Intercom Module Door Station User Manual
Figure 5-2 Device Management
Add Device
●
●
Click Add to add the indoor station or sub door station. Enter the
parameters and click OK to add.
Click Import. Enter the information of the device in the template to
import devices in batch.
Export
Click Export to export the information to the PC.
Delete
Select the device and click Delete to remove the selected device from the
list.
Refresh
Click Refresh to get the device information.
Optional: Set Device Information.
●
Click
to edit device information.
●
Click
to delete device information from the list.
●
Select Status and Device Type to search devices.
60
Video Intercom Module Door Station User Manual
5.3.2 Local Parameters Settings
You can configure the parameters of the live view, record files and captured pictures.
The record files and captured pictures are the ones you record and capture by using
the web browser. You can also set and view the saving paths of the captured pictures
and recorded videos on the PC that running the web browser.
Figure 5-3 Local Parameters
Live View Parameters
Stream Type
Set the stream type as Main Stream or Sub-stream.
Play Performance
Set the live view performance to Shortest Delay, Balanced or Fluent.
Auto Start Live View
Check Yes to enable the function.
Image Format
Select the image format for picture capture.
Click Save to enable the settings.
Record File Parameters
Record File Size
61
Video Intercom Module Door Station User Manual
Select the packed size of the manually recorded and downloaded video
files to 256M, 512M or 1G. After the selection, the maximum record file
size is the value you selected.
Save record files to
Set the saving path for the manually recorded video files.
Click Save to enable the settings.
Picture and Clip Settings
Save snapshots in live view to
Set the saving path of the manually captured pictures in live view mode.
Note
You can click Browse to change the directory for saving the clips and
pictures, and click Open to open the set folder of clips and picture saving.
Click Save to enable the settings.
5.3.3 System Settings
Follow the instructions below to configure the system settings, include System
Settings, Maintenance, Security, and User Management, etc.
Click System to enter the settings page.
Basic Information
Click System Settings → Basic Information to enter the settings page. On
the page, you can edit Device Name and Device No. Set the Language and
System Type according to your needs.
Click Save to enable the settings.
Time Settings
Click System Settings → Time Settings to enter the settings page. Select the
Time Zone of your location from the drop-down list.
62
Video Intercom Module Door Station User Manual
●
●
Enable NTP, set the Server Address, NTP Port and Interval.
Enable Manual Time Sync., set the time manually or check the Sync. with
computer time.
Click Save to enable the settings.
DST
Click System Settings → DST to check Enable DST. Set the parameters
according to your needs and click Save to enable the settings.
About
Click System Settings → About to enter the page. Click View Licenses to
view open source software Licenses.
Maintenance
Click Maintenance → Upgrade & Maintenance to enter the settings page.
Figure 5-4 Maintenance
●
Reboot: Click Reboot to reboot the device.
●
Default
Click Default to restore all parameters to default settings.
Restore All
Click Restore All to reset all the parameters, except the IP parameters
and user information, to the default settings.
63
Video Intercom Module Door Station User Manual
●
●
●
Export parameters:
1. Select Device Parameters, and click Export to pop up the dialog box.
2. Set and confirm the encryption password.
3. Click OK to export parameters.
Import Config. File:
1. Click browse icon to select the configuration file.
2. Click Import and enter the encryption password to import.
Upgrade:
1. Click browse icon to select the upgrade file.
2. Click Upgrade.
Note
○
○
The upgrading process will last 1 to 10 minutes, do not power off
during the upgrading. The device reboots automatically after
upgrading.
You can select controller, display module and sub modules to
upgrade.
Authentication
Click Security → Authentication to enter the settings page. On the page,
you can select RTSP Authenticationaccording to your actual needs.
Click Save to enable the settings.
Security Service
Click Security → Security Service to enter the settings page. On the page,
you can enable SSH according to your actual needs.
Click Save to enable the settings.
User Management
Click User Management to enter the settings page.
Administrator can edit the permission for the users.
64
Video Intercom Module Door Station User Manual
Note
We highly recommend you to create a strong password of your own
choosing (using a minimum of 8 characters, including at least three kinds of
following categories: upper case letters, lower case letters, numbers, and
special characters) in order to increase the security of your product. And we
recommend you change your password regularly, especially in the high
security system, changing the password monthly or weekly can better
protect your product.
Online Users
Click User Management → Online Users to enter the page.
Figure 5-5 Online Users
Click Refresh to get the present information.
Arming/Disarming Information
Click User Management → Arming/Disarming Information to view the
information. Click Refresh to get the present information.
5.3.4 Network Settings
TCP/IP Settings
TCP/IP settings must be properly configured before you operate the device over
network. The device supports IPv4.
Steps
1. Click Network → Basic Settings → TCP/IP to enter the settings page.
65
Video Intercom Module Door Station User Manual
Figure 5-6 TCP/IP Settings
2. Configure the network parameters.
- Check DHCP, the device will get the parameters automatically.
- Set the IPv4 Address, IPv4 Subnet Mask and IPv4 Default Gateway manually.
3. Configure the corresponding DNS server parameters.
4. Click Save to enable the settings.
Port Settings
Steps
1. Click Network → Basic Settings → Port to enter the settings page.
66
Video Intercom Module Door Station User Manual
Figure 5-7 Port Settings
2. Set the ports of the device.
HTTP Port
The default port number is 80, and it can be changed to any port No. which is
not occupied.
HTTPS Port
The default port number is 443, and it can be changed to any port No. which is
not occupied.
RTSP Port
The default port number is 554.
Server Port
The default server port number is 8000, and it can be changed to any port No.
ranges from 2000 to 65535.
3. Click Save to enable the settings.
SIP Setting
Steps
1. Click Network → Basic Settings → SIP to enter the settings page.
67
Video Intercom Module Door Station User Manual
Figure 5-8 SIP Settings
2. Check Enable VOIP Gateway.
3. Configure the SIP parameters.
4. Click Save to enable the settings.
FTP Settings
Steps
1. Click Network → Advanced → FTP to enter the settings page.
68
Video Intercom Module Door Station User Manual
Figure 5-9 FTP Settings
2. Check Enable FTP.
3. Select Server Type.
4. Input the Server IP Address and Port.
5. Configure the FTP Settings, and the user name and password are required for the
server login.
6. Set the Directory Structure, Parent Directory and Child Directory.
7. Set the picture naming rules.
69
Video Intercom Module Door Station User Manual
8. Click Save to enable the settings.
5.3.5 Video & Audio Settings
Video Parameters
Steps
1. Click Video/Audio → Video to enter the settings page.
Figure 5-10 Video Parameters
2. Select the Stream Type.
3. Configure the video parameters.
Stream Type
Select the stream type to main stream or sub stream.
Video Type
Select the stream type to video stream, or video & audio composite stream.
The audio signal will be recorded only when the Video Type is Video & Audio.
Resolution
Select the resolution of the video output.
Bitrate Type
Select the bitrate type to constant or variable.
Video Quality
70
Video Intercom Module Door Station User Manual
When bitrate type is selected as Variable, 6 levels of video quality are
selectable.
Frame Rate
Set the frame rate. The frame rate is to describe the frequency at which the
video stream is updated and it is measured by frames per second (fps). A
higher frame rate is advantageous when there is movement in the video
stream, as it maintains image quality throughout.
Max. Bitrate
Set the max. bitrate from 32 to 16384 Kbps. The higher value corresponds to
the higher video quality, but the better bandwidth is required.
Video Encoding
The device supports H.264.
I Frame Interval
Set I Frame Interval from 1 to 400.
4. Click Save to save the settings.
Audio Parameters
Steps
1. Click Video/Audio → Audio to enter the settings page.
Figure 5-11 Audio Settings
2. Configure the stream type and the audio encoding type.
Stream Type
Select the stream type to main stream or sub stream.
Audio Encoding
The device support G.711ulaw and G.711 alaw.
71
Video Intercom Module Door Station User Manual
3. Adjust the Input Volume, Output Volume and Speak Volume.
Note
Available range of volume: 0 to 10.
4. Click Save to save the settings.
5.3.6 Image Settings
Display Settings
Configure the image adjustment, backlight settings and other parameters in display
settings.
Steps
1. Click Image → Display Settings to enter the display settings page.
Figure 5-12 Display Settings
2. Select the Format.
3. Set the display parameters.
WDR
Wide Dynamic Range can be used when there is a high contrast of the bright
area and the dark area of the scene.
Brightness
Brightness describes bright of the image, which ranges from 1 to 100.
Contrast
72
Video Intercom Module Door Station User Manual
Contrast describes the contrast of the image, which ranges from 1 to 100.
Saturation
Saturation describes the colorfulness of the image color, which ranges from 1
to 100.
Sharpness
Sharpness describes the edge contrast of the image, which ranges from 1 to
100.
4. Set the Day/Night Mode.
Figure 5-13 Day/Night Mode
- Set Day Mode or Night Mode manually.
- Set the mode as Auto and edit the sensitivity according to your needs.
- Set the mode as Scheduled-Switch. Set the start time and end time.
Note
Daytime is from configured start time to configured time. The rest of the time is
set as night by default.
5. Set the backlight parameters.
73
Video Intercom Module Door Station User Manual
Figure 5-14 Backlight
1) Check the checkbox to enable BLC.
2) Select BLC Area.
6. Click Save to enable the settings.
OSD Settings
You can customize the camera name, time/date format, display mode, and OSD size
displayed on the live view.
Steps
1. Click Image → OSD Settings to enter the settings page.
2. Check the corresponding checkbox to select the display of camera name, date or
week if required.
3. Edit the Camera Name.
4. Select from the drop-down list to set the Time Format and Date Format.
5. Adjust the OSD position.
6. Click Save to enable the settings.
Target Cropping
Steps
1. Click Image → Crop to enter the page.
2. Check Enable Target Cropping to enable the function.
3. Click
to crop photo.
74
Video Intercom Module Door Station User Manual
4. Click
to crop video.
5. Select Cropping Resolution.
6. Click Save.
Note
●
●
You can select Cropping Resolution as 704*576, 1280*720, or 1920*1080.
You can zoom in or zoom out the image by selecting Cropping Resolutionafter
clicking Save.
5.3.7 Schedule Settings
You can create call schedule, or else the device will call indoor station all day by
default.
Steps
1. Click Schedule → Video Intercom → Call Schedule .
2. Click the next row below Enable Indoor Station All Day by Default.
3. Enter Schedule Name.
4. Select Call Type.
5. Set Weekly Schedule.
1) Click Weekly Schedule.
Figure 5-15 Weekly Schedule
2) Drag mouse to set the schedule according to the actual needs.
75
Video Intercom Module Door Station User Manual
3) Optional: Click the copy icon to copy the schedule to other days according to
the actual needs.
4) Click Save.
6. Set Holiday Schedule.
1) Click Holiday Schedule.
Figure 5-16 Holiday Schedule
2) Click Add.
3) Set Start Time and End Time.
4) Select Call Type.
5) Drag mouse to set the schedule according to the actual needs.
6) Click OK.
7) You can edit or delete the schedule according to the actual needs.
8) Click Save.
Note
The holiday schedule have higher priority than weekly schedule when you set
the two schedule at the same time.
5.3.8 Intercom Settings
Device No. Settings
76
Video Intercom Module Door Station User Manual
Steps
1. Click Device No. to enter the page.
Figure 5-17 Villa Door Station No. Settings
2. Select the device type from the drop-down list, and set the corresponding
information including Building No., Floor No., Door Station No., Community No.
and Unit No.
Note
When you select Doorphone as Device Type, only Community No., Building No.
and Unit No. can be set.
3. Click Save to enable the device number configuration.
Note
●
●
●
●
For main door station (D series or V series), the No. is 0.
For sub door station (D series or V series), the No. cannot be 0. The No.of sub
door station ranges from 1 to 99.
For each villa or building, at least one main door station (D series or V series)
should be configured, and one sub door stations (D series or V series) can be
customized.
For one main door station (D series or V series), up to 8 sub door stations can
be configured.
Linked Network Settings
77
Video Intercom Module Door Station User Manual
Steps
1. Go to Intercom → Session Settings to enter the settings page.
2. Set Register Number and Registration Password.
3. Set Main Station IP and VideoIntercom Server IP.
4. Enable Protocol 1.0.
5. Click Save to enable the settings.
Time Parameters
Go to Intercom → Time Parameters to enter the page.
Configure Max. Call Duration, Max. Message Duration, Max. Ring Duration, and
click Save.
Note
●
●
●
Max. call duration between the module indoor station and client ranges from 90 s
to 120 s. The call will end automatically when the actual calling duration is longer
than the configured one.
Max. message duration ranges from 30 s to 60 s. The message will end
automatically when the actual message duration is longer than the configured
one.
Max. ring duration refers to the maximum duration of the module indoor station
when it is called without being accepted. Max. ring duration ranges from 65 s to
255 s.
Ring-Back Tone Settings
Click Intercom → Ringbacktone Settings to enter the settings page.
Click Add to select the ring tone from PC.
Note
Available Audio Format: WAV、AAC, Size: Less than 600 KB, Sample Rate: 8000Hz,
Mono.
Press Button to Call
Steps
1. Go to Intercom → Press Button to Call to enter the settings page.
78
Video Intercom Module Door Station User Manual
Figure 5-18 Press Button to Call
2. Edit room No. in the button settings and select Link Time Schedule.
Note
●
●
The number of buttons may vary with different models. Please refer to the
actual product.
The schedule settings refers to Schedule Settings for details.
3. Click Save to enable the settings.
Input and Output
Go to Intercom → I/O Settings to enter the settings page.
Figure 5-19 IO Input and Output
Select I/O Input No., Input, I/O Output No. and Output.
Click Save to enable the settings.
Note
●
I/O Input supports 4-channel inputs.
79
Video Intercom Module Door Station User Manual
Table 5-1 I/O Input
●
I/O Input No.
Input
1
Door Status
2
Disable/Door Status
3
Exit Button
4
Disable/Exit Button
I/O Output supports 2-channel outputs.
Table 5-2 I/O Output
I/O Output No.
Output
1
Electric Lock
2
Disable/Electric Lock
Sub Module Configuration
Steps
1. Click Intercom → Sub Module Configuration , and you can view the sub module
information, including No., module type, status, and version.
2. Click to edit the sub module.
Display Module
●
Slide
to adjust Screen Backlight Brightness.
Slide Enable Buzzer to enable the function.
●
Touch-Display Module
Slide to adjust Screen Backlight Brightness.
●
Slide Enable Buzzer to enable the function.
●
Select Address Book Display Mode according to actual needs.
●
Enable Homepage Shortcut Dial, you can tap contact on the main page to call.
●
Click Add to add custom buttons.
●
80
Video Intercom Module Door Station User Manual
Note
●
●
●
The module address is used to differentiate the sub modules. See Configure Sub
Module Address for detailed configuration instructions.
For the other sub modules (indicator module, keypad module and card reader
module), it prompts Not supported.
The room No. for the main unit's call button is 1 by default; and the room No.
for the nametag modules call buttons are 2 to 7 by default.
Number Settings
Steps
1. Click Intercom → Number Settings , and you can view the No., room No., and SIP
number.
2. Add the number.
1) Click Add.
2) Enter Room No., and SIP.
3) Optional: Click Add to add SIP according to the actual needs.
4) Click OK.
3. Optional: Click
to edit the number.
5.3.9 Access Control Settings
Permission Password
Steps
1. Click Access Control → Password Settings to enter the settings page.
81
Video Intercom Module Door Station User Manual
Figure 5-20 Password Settings
2. Select Password Type.
3. Enter and confirm the password.
4. Click Save to enable the settings.
Door Parameters
Steps
1. Click Access Control → Door Parameters to enter the settings page.
Figure 5-21 Door Parameters
82
Video Intercom Module Door Station User Manual
2. Select the door and edit the door name.
3. Edit Open Duration.
4. Set door contact status.
5. Click Save to enable the settings.
Card Security
Click Access Control → Card Security to enter the settings page.
Slide to enable card encryption parameters.
Click Save to enable the settings.
Elevator Control
Before You Start
Make sure that the door station is in the mode of main door station. Only the main
door station supports elevator control function.
Steps
1. Click Access Control → Elevator Control Parameter to enter the settings page.
83
Video Intercom Module Door Station User Manual
Figure 5-22 Elevator Control
2. Check to enable elevator control function.
3. Select an Elevator No., and select an elevator controller type for the elevator.
4. Select Interface Type.
5. Enter Negative Floor Capacity, and select Alarm Receiver Type.
6. Enter the elevator controller's Server IP Address, Port No., User Name, and
Password.
7. Click Save to enable the settings.
Note
●
Up to 4 elevator controllers can be connected to one door station.
●
Up to 10 negative floors can be added.
●
Make sure the interface types of elevator controllers, which are connected to
the same door station are consistent.
84
Video Intercom Module Door Station User Manual
5.4 Organization Management
On the main page of the Client Software, click
the configuration page.
PersonalManagement to enter
5.4.1 Add Organization
Steps
1. In the organization list on the left, click +Add.
2. Enter the Organization Name as desired.
3. Click OK to save the adding.
4. Optional: You can add multiple levels of organizations according to the actual
needs.
1) You can add multiple levels of organizations according to the actual needs.
2) Then the added organization will be the sub-organization of the upper-level
organization.
Note
Up to 10 levels of organizations can be created.
5.4.2 Modify and Delete Organization
You can select the added organization and click
to modify its name.
You can select an organization, and click X button to delete it.
Note
●
●
The lower-level organizations will be deleted as well if you delete an organization.
Make sure there is no person added under the organization, or the organization
cannot be deleted.
5.5 Person Management
After adding the organization, you can add person to the organization and manage
the added person such as issuing cards in batch, importing and exporting person's
information in batch, etc.
85
Video Intercom Module Door Station User Manual
Note
●
Up to 2,000 persons can be added.
●
Up to 5 cards can be added to each person.
5.5.1 Add Person
Person information is necessary for the video intercom system. And when you set
linked device for the person, the intercom between intercom devices can be realized.
Steps
1. Select an organization in the organization list and click Add on the Person panel to
pop up the adding person dialog.
Note
The Person No. will be generated automatically and is editable.
2. Set basic person information.
1) Enter basic information: name, gender, tel, birthday details, effective period and
email address.
Note
The length of person name should be less than 15 characters.
2) Click Add face to upload the photo.
Note
The picture should be in *.jpg format.
Click Upload
Select the person picture from the local PC to upload it
to the client.
Click Take Phone
Take the person's photo with the PC camera.
Click Remote
Collection
Take the person's photo with the collection device.
3. Issue the card for the person.
1) Click Credential → Card .
2) Click + to pop up the Add Card dialog.
3) Select Normal Card as Card Type.
4) Enter the Card No.
86
Video Intercom Module Door Station User Manual
5) Click Read and the card(s) will be issued to the person.
4. Link the device to the person.
1) Set the linked devices.
Linked Device
You can bind the indoor station to the person.
Note
If you select Analog Indoor Station in the Linked Device, the Door Station
field will display and you are required to select the door station to
communicate with the analog indoor station.
Room No.
You can enter the room No. of the person.
2) Click OK to save the settings.
5. Click Add to save the settings.
5.5.2 Modify and Delete Person
Select the person and click Edit to open the editing person dialog.
To delete the person, select a person and click Delete to delete it.
Note
If a card is issued to the current person, the linkage will be invalid after the person is
deleted.
5.5.3 Import and Export Person Information
The person information can be imported and exported in batch.
Steps
1. Exporting Person: You can export the added persons' information in Excel format
to the local PC.
1) After adding the person, you can click Export Person to pop up the following
dialog.
2) Click ... to select the path of saving the exported Excel file.
3) Check the checkboxes to select the person information to export.
4) Click OK to start exporting.
87
Video Intercom Module Door Station User Manual
2. Importing Person: You can import the Excel file with persons information in batch
from the local PC.
1) Click Import Person.
2) You can click Download Template for Importing Person to download the
template first.
3) Input the person information to the downloaded template.
4) Click ... to select the Excel file with person information.
5) Click OK to start importing.
5.5.4 Get Person Information from Device
If the added device has been configured with person information (including person
details, fingerprint, issued card information), you can get the person information
from the device and import to the client for further operation.
Steps
Note
This function is only supported by the device the connection mothod of which is
TCP/IP when adding the device.
1. In the organization list on the left, click to select an organization to import the
persons.
2. Click Get from Device to pop up the dialog box.
3. The added device will be displayed.
4. Click to select the device and then click Get to start getting the person information
from the device.
Note
●
●
●
The person information, including person details, person's fingerprint
information (if configured), and the linked card (if configured), will be imported
to the selected organization.
If the person name stored in the device is empty, the person name will be filled
with the issued card No. after importing to the client.
The gender of the persons will be Male by default.
5.5.5 Change Person to Other Organization
You can move the person to another organization if needed.
88
Video Intercom Module Door Station User Manual
Steps
1. Select the person in the list and click Change Organization.
2. Select the organization to move the person to.
3. Click OK to save the settings.
5.5.6 Issue Card in Batch
You can issue multiple cards for the person with no card issued in batch.
Steps
1. Click Batch Issue Cards to enter the dialog page. All the added person with no card
issued will display in the Person(s) with No Card Issued list.
Figure 5-23 Issue Card in Batch
2. Click Settings.
89
Video Intercom Module Door Station User Manual
Figure 5-24 Card Settings
3. Select Card Type and Card No. Type.
4. Click OK to save the settings.
Result
After issuing the card to the person, the person and card information will display in
the Person(s) with Card Issued list.
5.5.7 Permission Settings
Add Permissions
Steps
1. On the main page, click
page.
AccessControlInfo → Access Group to enter the
2. Click +Add to pop up the adding dialog box.
3. Configure the parameters.
90
Video Intercom Module Door Station User Manual
1) Enter the Name of the permission.
2) Select the Template of the schedule.
3) Check the person to Selected according to your needs.
4) Check the device to Selected according to your needs.
4. Click Save.
5. Check the permission and click Apply All to Device.
The status of the permission displays as Applied.
6. Optional: Click Applying Status to check the details.
Modify/Delete Permissions
On the page of the permission settings, click
permission.
to edit the parameters of the
Select one or more permissions, click Delete to remove the permissions.
91
Video Intercom Module Door Station User Manual
6 Video Intercom Operation
6.1 Video Intercom Operation via Device
6.1.1 Call Resident
Note
●
Make sure you have configured the room No. of the device.
●
Make sure you have add contacts to the device via iVMS-4200 Client Software.
Call Resident via Main Module or Nametag Module
Press the call button on the main unit or on the nametag unit.
Call Resident via Keypad Module
Enter the Room No. on the keypad module, and press # to start calling.
Note
You can press * via keypad module to hang up.
Call Resident via Display Module
Press
on the display module to enter the contact list.
Figure 6-1 Contacts
Press or hold ˄/˅ to select a contact.
92
Video Intercom Module Door Station User Manual
Press OK and confirm to call.
Note
●
Hold ˄ or ˅ to scroll the page up or down faster.
●
You can press Back button via display module to hang up.
Call Resident via Touch-Display Module
You can call corresponding resident in the two ways. They are:
●
On the main page of the touch-display module, tap
to call.
and enter the No.
Figure 6-2 Call Residents
●
On the main page of the touch-display module, tap
in the list to call.
to select a contact
Note
Two themes of the main page are supported. You can change it remotely via
client software.
6.1.2 Issue Card
Before You Start
Make sure you have issue the card locally or remotely. See Person Management for
issuing card via Client software for details.
Issue Card via Main Card: You can swipe card to issue it after swiping the main card
in advance.
Steps
1. Present the main card on the card reading area, and hear two beeps.
93
Video Intercom Module Door Station User Manual
2. Present the unauthorized sub cards in turn after hearing a beep.
3. Present the main card again to end the card issuing process.
Note
●
●
●
DS-KD-M/DS-KD-TDM supports Mifare card, DS-KD-E/DS-KD-TDE supports EM
card.
If the amount of sub cards exceeds 10000, no more sub cards can be issued.
Up to 5 sub cards can be issued once. The issued frequency is no more than
2000.
6.1.3 Unlock Door
Unlock Door by Password
You can unlock the door by entering the password via the keypad module or
touch-display module.
Note
On the main page of touch-display module, tap
page to unlock the door.
to enter the call/unlock
Figure 6-3 Call/Unlock
Four formats of password are supported. They are:
●
【#】+ Public Password +【#】
●
【#】+ Password +【#】
●
【#】+ Duress Password +【#】
94
Video Intercom Module Door Station User Manual
Note
●
Password contains 6 digits.
●
You're allowed to set 3 public passwords via iVMS-4200 client software.
●
The password varies according to different rooms.
Unlock Door by Card
Note
Make sure the card has been issued. You can issue the card via the door
station, or via iVMS-4200 client software.
Present the card on the card induction area via card reader module or
touch-display module (with card reading function) to unlock the door.
Note
The main card does not support unlocking the door.
6.2 Video Intercom Operation via Client Software
The Video Intercom Management module provides the function of video intercom,
checking call logs and managing notice via the iVMS-4200 Client Software.
Note
For the user with access control module permissions, the user can enter the Access
Control module and manage video intercom and search information.
You should add the device to the software and configure the person to link the
device in Access Control module before your configuration remotely.
Click
AccessControlInfo → Video Intercom → Video Intercom on the left bar
to enter the Video Intercom page.
6.2.1 Receive Call from Door Station
Steps
1. Select the client software in door station page to start calling the client and an
incoming call dialog will pop up in the client software.
95
Video Intercom Module Door Station User Manual
Figure 6-4 Device Call
2. Click Answer to answer the call. Or click Hang Up to decline the call.
3. After you answer the call, you will enter the In Call page.
Adjust the Volume of
Loudspeaker
Click
Hang Up
Click Hang Up to hang up.
Adjust the Volume of
Microphone
Click
Unlock Remotely
For door station, you can click
door remotely.
to adjust the volume of loudspeaker.
to adjust the volume of the microphone.
to open the
Note
●
●
●
●
One video intercom device can only connect with one client software.
The maximum ring duration can be set from 15s to 60s via the Remote
Configuration of the video intercom device.
The maximum speaking duration between indoor station and iVMS-4200 can be
set from 120s to 600s via the Remote Configuration of indoor station.
The maximum speaking duration between door station and iVMS-4200 can be
set from 90s to 120s via the Remote Configuration of door station.
96
Video Intercom Module Door Station User Manual
6.2.2 Live View via Door Station
You can get the live view of the main unit in the Main View module and control the
door station remotely.
In the Main View module, double-click a door station or drag the device to a display
window to start the live view.
Right click on the live view page, clickthe unlock icon to remote unlock the door.
6.2.3 View Call Logs
Before You Start
You can check all the call logs, including dialed call logs, received call logs and missed
call logs. You can also directly dial via the log list and clear the logs.
Steps
1. In the Video Intercom page, click Call Log to enter the Call Log page.
Figure 6-5 View Call Logs
All the call logs will display on this page and you can check the log information,
e.g., call status, start time, resident's organization and name, device name and
ring or speaking duration.
2. Optional: Click the call button to re-dial the resident.
6.2.4 Search Video Intercom Information
97
Video Intercom Module Door Station User Manual
You can search the call logs between the iVMS-4200 client software and video
intercom devices, device unlocking logs and the sent notice information.
In the main page, click
AccessControlInfo to enter the access control module.
In the Access Control module, click Video Intercom.
Search Call Logs
Steps
1. In the Video Intercom page, click Call Log to enter the Call Log page.
Figure 6-6 Call Logs
2. Set the search conditions, including call status, device type, start time and end
time.
Call Status
Click ˅to unfold the drop-down list and select the call status as Dialed,
Received or Missed. Or select All to search logs with all statuses.
Device Type
Click ˅ to unfold the drop-down list and select the device type as Indoor
Station, Door Station, Outer Door Station or Analog Indoor Station. Or select
All Devices to search logs with all device types.
Day Mode Start Time/Day Mode End Time
Click
logs.
to specify the start time and end time of a time period to search the
98
Video Intercom Module Door Station User Manual
Reset the Settings
Click Reset to reset all the configured search conditions.
3. Click Search and all the matched call logs will display on this page.
4. Optional: Check the detailed information of searched call logs, such as call status,
ring/speaking duration, device name, resident organization, etc.
5. Optional: Input keywords in the Search field to filter the desired log.
6. Optional: Click Export to export the call logs to your PC.
Search Unlocking Logs
Steps
1. In the Information Search page, click Unlocking Log to enter the Unlocking Log
page.
Figure 6-7 Unlocking Logs
2. Set the search conditions, including unlocking type, device type, start time and
end time.
Unlocking Type
Click ˅ to unfold the drop-down list and select the unlocking type as Unlock by
Password, Unlock by Duress, Unlock by Card, Unlock by Resident or Unlock
by Center. Or select All to search logs with all unlocking types.
Device Type
99
Video Intercom Module Door Station User Manual
Click ˅ to unfold the drop-down list and select the device type as Door Station
or Door Station (V Series). Or select All Devices to search logs with all device
types.
Start Time/End Time
Click
logs.
to specify the start time and end time of a time period to search the
`Reset the Settings
Click Reset` to reset all the configured search conditions.
3. Click Search and all the matched unlocking logs will display on the page.
4. Optional: Check the detailed information of searched unlocking logs, such as
unlocked time, card No., device No., etc.
5. Optional: Input keywords in the Search field to filter the searching result.
6. Optional: Click
on the Capture column to view the captured pictures.
Note
Viewing captured picture should be supported by device.
7. Optional: Click Export to export the unlocking logs to your PC.
100
Video Intercom Module Door Station User Manual
A. Relevant Instructions for External
Power Supply and Wiring of 2-wire Video
Intercom Products (2020-1-20)
Power Description
2-Wire Distributor
DS-KAD706
DS-KAD704
CH6
CH1 to CH5
16 W
6W
CH4
CH1 to CH3
16 W
6W
Modular Door Station
The main module & the sub-module maximum power consumption.
Model
Stable Power Consumption
DS-KD8003-IME2
4W
DS-KD-KK
0.8 W
DS-KD-KP
1W
DS-KD-DIS
2.5 W
DS-KD-E
0.8 W
DS-KD-M
0.8 W
DS-KD-INFO
1.5 W
Indoor Station
101
Video Intercom Module Door Station User Manual
Model
Stable Power Consumption
DS-KH6320-WTE2
6W
Example of the Calculation Model of the Modular Door
Station Sub-Module
The sum of the power consumption of each module must be less than the
total power consumption of the power supply.
2-Wire
Model
DS-KD8003- DS-KD-DIS
IME2
DS-KD-KP
DS-KD-M
/
Quantity
1
1
2
2
/
Power
4W
2.5 W
2W
1.6 W
Total: 10.1
W
Because 10.1 W ≤ 16 W, we can support powering this device through
KAD706 channel 6 or KAD704 channel 4.
2-Wire
Model
DS-KD8003IME2
DS-KD-M
DS-KD-KK
/
Quantity
1
1
12
/
Power
4W
0.8 W
9.6 W
Total: 14.4 W
Because 14.4 W ≤ 16 W, we can support powering this device through
KAD706 channel 6 or KAD704 channel 4.
102
Video Intercom Module Door Station User Manual
Wire Testing Standards
●
●
●
●
When there are multiple cores in one parallel line, only one pair of closed
cores are allowed to transmit signal. It is not allowed to use multiple pair
of cores in one cable to transmit signal.
When using parallel lines, it is suggested to use those with shielding layer.
If dual core or multiple core parallel lines without shielding layer are
routed, stability of signal transmission can be effected. You need to run a
test before installation.
Impedance of twist pair in network cable are over 42 Ω/100 m, so
network cable cannot transmit enough power to indoor station. Network
cable is not allowed to use during installation.
Strong electricity and weak electricity cannot be wired in the same route,
they need to be wired separately and the distance should be more than
0.5 meter.
Table A-1 Table A
Routing
Path
Twisted
Pair : 24
AWG (0.2
mm2)
Twisted
Pair : 20
AWG (0.5
mm2)
Twisted
Pair :
18AWG
(0.8 mm2)
Twisted
Pair :
16AWG (1
mm2)
Parallel
lines (0.5
mm2 to 0.8
mm2)
DSTransmissio Transmissio Transmissio Transmissio Transmissio
KAD706-S- n Distance n Distance n Distance n Distance n Distance
DS-KAD706 ≤ 60 m
≤ 60 m
≤ 60 m
≤ 50 m
≤ 35 m
DSTransmissio Transmissio Transmissio Transmissio Transmissio
KAD706n Distance n Distance n Distance n Distance n Distance
DS-KAD706 ≤ 60 m
≤ 60 m
≤ 60 m
≤ 50 m
≤ 35 m
DSKAD706DS-
Transmissio Transmissio Transmissio Transmissio Transmissio
n Distance n Distance n Distance n Distance n Distance
≤ 35 m
≤ 60 m
≤ 60 m
≤ 50 m
≤ 35 m
103
Video Intercom Module Door Station User Manual
Routing
Path
Twisted
Pair : 24
AWG (0.2
mm2)
Twisted
Pair : 20
AWG (0.5
mm2)
Twisted
Pair :
18AWG
(0.8 mm2)
Twisted
Pair :
16AWG (1
mm2)
Parallel
lines (0.5
mm2 to 0.8
mm2)
KD8003IME2
DSKAD706DSKH6320WTE2
Transmissio Transmissio Transmissio Transmissio More
n Distance n Distance n Distance n Distance parameters
≤ 35 m
≤ 100 m
≤ 100 m
≤ 100 m
in Table B
Routing Path
Parallel lines:
24 AWG (0.2
mm2)
Parallel lines:
20 AWG (0.5
mm2)
Parallel lines:
18 AWG (0.8
mm2)
Parallel lines:
16 AWG (1
mm2)
DS-KAD706DS- KH6320WTE2
Transmission
Distance ≤ 50
m
Transmission
Distance ≤
100 m
Transmission
Distance ≤
100 m
Transmission
Distance ≤
100 m
Device Installation
●
●
●
●
Installation environment (temperature, moisture etc.) need to follow
requirements in specification or power output can be effected.
Power consumption of modular door station (main module and sub
modules) should be less than 12W. Please reach local technical support if
you are not sure about power consumption of each module. Door station
should be connected to CH6 of the video/audio distributor. If modular
door station is connected to any terminal of CH1 to CH5, up to 3 sub
modules can be connected.
Indoor station should be connected to any terminal of CH1 to CH5 of the
video/audio distributor.
Up to 15 video/audio distributor can be cascaded. If more distributors are
needed, you should cascade network switch supporting 1000 Mbps. The
whole 2-wire system can have up to 500 devices.
104
Video Intercom Module Door Station User Manual
●
Power supply must be certified by Hikvision.
●
Indoor station needs to use firmware released after October, 2019.
105
Video Intercom Module Door Station User Manual
B. Communication Matrix and Device
Command
Communication Matrix
Scan the following QR code to get the device communication matrix.
Note that the matrix contains all communication ports of Hikvision access
control and video intercom devices.
Figure B-1 QR Code of Communication Matrix
Device Command
Scan the following QR code to get the device common serial port
commands.
Note that the command list contains all commonly used serial ports
commands for all Hikvision access control and video intercom devices.
Figure B-2 Device Command
106
UD23547B-A
">