Asus | DSL-N10S | User manual | Asus DSL-N10S User manual

DSL-N10S
Wireless-N150 ADSL Modem Router
User Manual
E9742
First Edition
September 2014
Copyright © 2014 ASUSTeK Computer Inc. All Rights Reserved.
No part of this manual, including the products and software described in it, may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language in any form or by any means, except documentation kept by the purchaser for
backup purposes, without the express written permission of ASUSTeK Computer Inc.
(“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or
altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2)
the serial number of the product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES
OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE
LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES
(INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE
OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR
ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED
FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME
WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY
ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR
INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS
AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered
trademarks or copyrights of their respective companies, and are used only for identification or
explanation and to the owners’ benefit, without intent to infringe.
Offer to Provide Source Code of Certain Software
This product contains copyrighted software that is licensed under the General Public License
(“GPL”), under the Lesser General Public License Version (“LGPL”) and/or other Free Open
Source Software Licenses. Such software in this product is distributed without any warranty
to the extent permitted by the applicable law. Copies of these licenses are included in this
product.
Where the applicable license entitles you to the source code of such software and/or other
additional data, such data should have been shipped along with this product.
You may also download it for free from http://support.asus.com/download.
The source code is distributed WITHOUT ANY WARRANTY and licensed under the same
license as the corresponding binary/object code.
ASUSTeK is eager to duly provide complete source code as required under various Free
Open Source Software licenses. If however you encounter any problems in obtaining the
full corresponding source code we would be much obliged if you give us a notification to the
email address gpl@asus.com, stating the product and describing the problem (please do
NOT send large attachments such as source code archives etc to this email address).
2
Table of contents
About this guide..................................................................................... 5
Chapter 1
Knowing your wireless router
Package contents................................................................................... 7
System requirements............................................................................. 7
Before you proceed................................................................................ 7
Hardware features.................................................................................. 8
Chapter 2
Getting started
Setting up the wireless router............................................................. 13
Accessing the router’s web GUI....................................................... 13
Using the Quick Internet Setup (QIS)............................................... 14
Chapter 3
Configuring the network clients
Managing your network clients........................................................... 17
Chapter 4
Configuring via the web GUI
Configuring the Interface Setup.......................................................... 21
Configuring the Internet settings...................................................... 21
Configuring the local area network (LAN) settings........................... 23
Configuring the wireless network settings........................................ 24
Configuring the Advanced Setup........................................................ 25
Configure the firewall settings.......................................................... 25
Configuring the routing settings....................................................... 26
Configure the NAT settings.............................................................. 27
Configure the ADSL settings............................................................ 28
Configuring the Access Management................................................ 29
Configuring the ACL......................................................................... 29
Configuring the UPnP settings......................................................... 31
Configuring the DDNS settings........................................................ 32
Configuring the Maintenance.............................................................. 33
Configuring the Administrator........................................................... 33
Upgrading the firmware.................................................................... 34
Restoring the wireless router’s settings........................................... 35
Diagnostics....................................................................................... 36
3
Table of contents
Status..................................................................................................... 37
Checking your device information and basic settings...................... 37
Configuring the System Log............................................................. 38
Setting up the Wi-Fi Protected Setup (WPS)...................................... 39
Chapter 5
Troubleshooting
Troubleshooting................................................................................... 40
Appendices
Notices................................................................................................... 43
ASUS Contact Information................................................................... 52
Networks Global Hotline Information................................................. 53
4
About this guide
This user guide contains information that you need to install and configure the
ASUS Wireless Router.
How this guide is organized
This guide contains the following parts:
• Chapter 1: Knowing your wireless router
This chapter provides information on the package contents, system
requirements, hardware features, and LED indicators of the ASUS Wireless
Router.
• Chapter 2: Getting started
This chapter provides instructions on accessing the router’s web GUI and
quickly setting up the Internet connection via the Quick Internet Setup (QIS)
function.
• Chapter 3: Configuring the network clients
This chapter provides instructions on setting up the clients in your network to
work with your ASUS Wireless Router.
• Chapter 4: Configuring via the web GUI
This chapter provides instructions on configuring the ASUS Wireless Router’s
Internet service settings, advanced settings, administration settings, diagnostic
settings, and viewing your router’s status.
• Chapter 5: Troubleshooting
This chapter provides you with a troubleshooting guide for solving common
problems you may encounter when using the ASUS Wireless Router.
• Appendices
This chapter provides you with the regulatory Notices and Safety Statements.
5
Conventions used in this guide
WARNING: Information to prevent injury to yourself when trying to complete a task.
CAUTION: Information to prevent damage to the components when trying to complete a task.
IMPORTANT: Instructions that you MUST follow to complete a task.
NOTE: Tips and additional information to aid in completing a task.
6
1
Knowing your
wireless router
Package contents
Check the following items in your ASUS Wireless Router package.
DSL-N10S Wireless-N150 ADSL Modem Router
RJ-45 cable
RJ-11 cable
Power adapter
Warranty card
Quick Start Guide
External splitter
Note: If any of the items is damaged or missing, contact your retailer.
System requirements
Before installing the ASUS Wireless Router, ensure that your system/network
meets the following requirements:
•
•
•
•
An Ethernet RJ-45 port (10Base-T/100Base-TX)
At least one IEEE 802.11b/g/n device with wireless capability
An installed TCP/IP and Internet browser
Operating system: Windows98® SE and higher
Before you proceed
Take note of the following guidelines before installing the ASUS Wireless Router:
• The length of the Ethernet cable that connects the device to the network (hub,
ADSL/cable modem, router, wall patch) must not exceed 100 meters.
• Place the device on a flat and stable surface as far from the ground as
possible.
• Keep the device clear from metal obstructions and away from direct sunlight.
Chapter 1: Knowing your wireless routerDSL-N10S
7
• Keep the device away from transformers, heavy-duty motors, fluorescent lights,
microwave ovens, refrigerators, and other industrial equipment to prevent
signal loss.
• Install the device in a central area to provide ideal coverage for all wireless
mobile devices.
• Install the device at least 20cm from a person to comply with the RF Guidelines
for Human Exposure of the Federal Communications Commission (FCC).
Hardware features
Top panel
Status indicators
LED
8
Status
Indication
Off
No power
On
Power on
Slow Flash
No signal detected
Fast Flash
The device is synchronizing with the DSL
device
On
The device is connected to the DSL
device.
DSL-N10SChapter 1: Knowing your wireless router
Status indicators
LED
Status
Indication
Off
No connection or in bridge mode.
Flashing
Internet data is transmitted in the routing
mode.
On
The Internet connection is normal in the
routing mode and no Internet data is
being transmitted.
Off
No power or no physical connection
On
Has physical connection to an Ethernet
network.
Flashing
Transmitting or receiving data (through
Ethernet cable)
Off
Inactive WLAN connection
On
Active WLAN connection
Flashing
Transmitting data through the WLAN
interface
Off
Inactive WPS connection
On
WPS connection is successful
Flashing
WPS is active and the wireless router
is waiting for the client to successfully
connect to it.
Chapter 1: Knowing your wireless routerDSL-N10S
9
Rear panel & Side panels
10
DSL-N10SChapter 1: Knowing your wireless router
Item
Description
Power switch
Press this button to turn the power on/off.
Power (DC-In) port
Insert the AC adapter into this port to connect your router to a
power source.
LAN port
Connect a RJ-45 Ethernet cable to this port to establish LAN
connection.
ADSL port
Connect an RJ-11 telephone cable to this port or a splitter
connected from this port.
WPS button / Wi-Fi switch*
WPS mode: Press this button for more than four seconds to enable
the WPS function.
Wi-Fi switch mode: Press this button to turn on/off the Wi-Fi
function.
*• W
i-Fi switch function is only available in some countries or
regions.
• If you press the button for less than four seconds, the Wi-Fi
function will not be enabled.
WLAN button
Press this button to enable or disable WLAN function.
Reset button
Using a pointed blunt object, press this button for more than one
second to reset the system to its factory default settings.
Air vents
These vents provide ventilation to your router.
Chapter 1: Knowing your wireless routerDSL-N10S
11
12
DSL-N10SChapter 1: Knowing your wireless router
2
Getting started
Setting up the wireless router
The ASUS Wireless Router includes a web graphical user interface (web GUI)
that allows you to configure the wireless router using your web browser on your
computer.
Note: For details on configuring your wireless router using the web GUI, refer to Chapter 4:
Configuring via the web GUI.
Accessing the router’s web GUI
To access the router’s web GUI:
1. In your web browser, key in http://192.168.1.1.
2. Key in the user name and password. You may choose to log in as
administrator (user name/password: admin) or as an ordinary user (user
name/password: user/user).
Note: When you log in as the administrator, the Quick Internet Setup (QIS) Wizard is displayed.
For details about the QIS Wizard, refer to the next section Using the Quick Internet Setup
(QIS).
Chapter 2: Getting startedDSL-N10S
13
Using the Quick Internet Setup (QIS)
The Quick Internet Setup (QIS) function guides you in quickly setting up your
Internet connection.
Important: Obtain the necessary information about your Internet connection type from your ISP.
1. Click Quick Start.
2. In Step 1: Quick Start - Password page, set up your password and click
Next.
3. In Step 2: Quick Start - Time Zone page, select the appropriate time for
your location and click Next.
14
DSL-N10SChapter 2: Getting started
4. In Step 3: Quick Start - ISP Connection Type page, select your Internet
connection type, and click Next.
Chapter 2: Getting startedDSL-N10S
15
5. In Step 4: Quick Start - Wlan page, set up the parameter for your WLAN
network.
Notes:
• Do not include quotation marks (" or ') in your SSID or use spaces at the start of your SSID.
• For WPA pre-shared key and WEP key settings, do not use quotation marks (" or '), angle
brackets (>), square brackets (]) and spaces at the start of your key, and spaces at the start
or two spaces between your key.
6. In Step 5: Quick Start Complete!! page, click Next to save the
configuration settings. Click Back to modify the settings. Click Exit to
cancel the settings.
16
DSL-N10SChapter 2: Getting started
3
Configuring the
network clients
Managing your network clients
To manage your network clients to your ASUS Wireless Router, you must have the
correct parameters for wireless, LAN, and WAN connection types. Ensure that the
clients’ IP addresses are within the same subnet as the ASUS Wireless Router.
By default, the ASUS Wireless Router integrates the DHCP server function that
automatically assigns the IP addresses to the clients in your network. You may also
manually assign the static IP addresses to selected clients in your network.
Note: ASUS recommends the following settings in establishing manually assigned IP addresses
to your client in the Router mode:
• IP address: 192.168.1.xxx (xxx can be any number between 2 and 254. Ensure that the IP address is not used by another device)
• Subnet Mask: 255.255.255.0 (same as the ASUS Wireless Router)
• Gateway: 192.168.1.1 (IP address of the ASUS Wireless Router)
• DNS: 192.168.1.1 (ASUS Wireless Router) or assign a known DNS server in your network
Chapter 3: Configuring the network clients
DSL-N10S
17
Windows® 2000
1.Click Start > Control Panel >
Network and Dial-up Connection.
Right-click Local Area Connection,
then click Properties.
2.Select Internet Protocol (TCP/IP),
then click Properties.
3.Select Obtain an IP address
automatically if you want
the IP settings to be assigned
automatically. Otherwise, select
Use the following IP address: and
key in IP address, Subnet mask,
and Default gateway.
4.Select Obtain DNS server
address automatically if you
want the DNS server settings to be
assigned automatically. Otherwise,
select Use the following DNS
server addresses: and key in the
Preferred and Alternate DNS
server.
5.Click OK when done.
18
DSL-N10S
Chapter 3: Configuring the network clients
Windows® XP
1.Click Start > Control Panel >
Network Connection. Right-click
Local Area Connection, then
select Properties.
2.Select Internet Protocol (TCP/IP),
then click Properties.
3.Select Obtain an IP address
automatically if you want
the IP settings to be assigned
automatically. Otherwise, select
Use the following IP address: and
key in IP address, Subnet mask,
and Default gateway.
4.Select Obtain DNS server
address automatically if you
want the DNS server settings to be
assigned automatically. Otherwise,
select Use the following DNS
server addresses: and key in the
Preferred and Alternate DNS
server.
5.Click OK when done.
Chapter 3: Configuring the network clients
DSL-N10S
19
Windows® Vista/7
1.Click Start > Control Panel >
Network and Internet > Network
and Sharing Center. Click View
status > Properties > Continue.
2.Select Internet Protocol
Version 4 (TCP/IPv4), then click
Properties.
3.Select Obtain an IP address
automatically if you want
the IP settings to be assigned
automatically. Otherwise, select
Use the following IP address:
and key in IP address and
Subnet mask.
4.Select Obtain DNS server
address automatically if you
want the DNS server settings
to be assigned automatically.
Otherwise, select Use the
following DNS server
addresses: and key in the
Preferred and Alternate DNS
server.
5.Click OK when done.
20
DSL-N10S
Chapter 3: Configuring the network clients
4
Configuring via
the web GUI
Configuring the Interface Setup
The Interface Setup page allows you to configure the settings of these three
network types: Internet, LAN, and Wireless.
Configuring the Internet settings
The Internet page allows you to configure your Internet settings.
Chapter 4: Configuring via the web GUI
DSL-N10S
21
To configure the Internet settings:
1. Click Interface Setup > Internet tab.
2. In the AMT VC dropdown list, select the virtual circuit, and key in the virtual
path values for the asynchronous transfer mode ranging from 0 to 255 in the
VPI field, and the VCI values ranging from 1 to 65535.
3. In the IPv4/IPv6 field, select IPv4, IPv4/IPv6 or IPv6.
4. In the Encapsulation item, select Dynamic IP Address, Static IP address,
PPPoA/PPPoE or Bridge Mode.
To configure the PPP settings:
1. In the User Name and Password fields, key in the user name and password
provided by your ISP.
2. In the Connection Settings list, you can select Always On
(Recommended), Connect on Demand, or Connect Manually. If you select
Connect on Demand type, key in the time of inactivity (in minutes) when the
Internet connection is automatically disconnected.
3. Click SAVE to apply the settings made.
22
DSL-N10S
Chapter 4: Configuring via the web GUI
Configuring the local area network (LAN) settings
The LAN page allows you to configure your local area network (LAN) settings.
Configuring the LAN settings
The LAN page allows you to configure the interface of your local area network.
To configure the LAN settings:
1. Click Interface Setup > LAN tab. In the Router Local IP field, key in the IP
Address and IP Subnet Mask.
2. In the DHCP options, select Disabled, Enabled, or Relay.
3. Key in the Starting IP Address, IP Pool Count and Lease Time. Select a
DNS Relay mode from the dropdown list.
4. Click SAVE to apply the settings made or CANCEL to discard changes.
Chapter 4: Configuring via the web GUI
DSL-N10S
23
Configuring the wireless network settings
The Wireless page allows you to configure the wireless settings.
Configuring the basic wireless network settings
To configure the wireless settings:
1. Click Interface Setup > Wireless tab.
2. In the Access Point Settings, select Activated or Deactivated to enable or
disable the access point.
3. Key in the necessary parameters for Access Point and select the wireless
mode.
4. In the 11n Settings field, select from the dropdown list the channel bandwidth
to accommodate higher transmission speeds.
5. In the Multiple SSIDs Settings field, tick Yes or No to enable/disable
broadcast SSID or WPS, then key in the SSID you want to use. Assign a
24
DSL-N10S
Chapter 4: Configuring via the web GUI
unique name containing up to 32 characters for your SSID (Service Set
Identifier) or network name to identify your wireless network. Wi-Fi devices
can identify and connect to the wireless network via your assigned SSID. The
SSIDs on the information banner are updated once new SSIDs are saved to
the settings. Select the Authentication type.
6. In WDS Settings field, tick On or Off to enable or disable the WDS (Wireless
Distribution System).
7. In MAC Address Filter field, click Activated or Deactivated to enable or
disable the MAC address filter function. Select Allow Association or Deny
Association from the dropdown list to allow or block access to the wireless
network for those network clients whose MAC addresses are on the list.
8. Click SAVE to apply the settings made or CANCEL to discard changes.
Configuring the Advanced Setup
The Advanced Setup page allows you to configure the following advanced
settings: Firewall, routing, NAT, VLAN and ADSL.
Configure the firewall settings
The Firewall page allows you to enable or disable the firewall and SPI functions.
Chapter 4: Configuring via the web GUI
DSL-N10S
25
Configuring the routing settings
The Routing page displays the devices on the routing list and allows you to
configure the routing settings.
Configuring the routing settings
If your network makes use of more than one wireless router, you can configure a
routing table to share the same Internet service.
Note: We recommend that you do not change the default route settings unless you have
advanced knowledge of routing tables.
If you want to add a device on the list, click ADD ROUTE. The following screen
appears. Key in the necessary parameter for the new device and click SAVE when
finish.
26
DSL-N10S
Chapter 4: Configuring via the web GUI
Configure the NAT settings
NAT (Network Address Translation) allows a Virtual Private Network (VPN)
connection to pass through the router to the network clients.
To configure the NAT settings:
1. Go to Advanced Setup > NAT.
2. Select the Virtual Circuit and Number of IPs.
3.Enter DMZ and Virtual Servers settings.
4.Click Save.
Chapter 4: Configuring via the web GUI
DSL-N10S
27
Configure the ADSL settings
This page allows you to configure the ADSL settings. Select the ADSL mode and
ADSL type, click SAVE when done.
28
DSL-N10S
Chapter 4: Configuring via the web GUI
Configuring the Access Management
The Advanced Setup page allows you to configure the following advanced
settings: ACL, Filter, SNMP, UPnP, and DDNS.
Configuring the ACL
The ACL (Access Control List) configuration page allows you to specify the
services that are accessible from LAN or WAN side.
To configure the ACL settings:
1. Click Access Management > ACL tab.
2. In ACL, tick Activated to enable ACL management.
3. In the IP Address fields, key in the desired IP to add.
4. Click Save.
Chapter 4: Configuring via the web GUI
DSL-N10S
29
Configure the Filter settings
The Filter page allows you to restrict certain types of outgoing or incoming data
packets from or to the network clients based on their MAC addresses.
To configure the Filter settings:
1. Click Access Management > Filter tab.
2. Select the Filter Type Selection.
3. In the Direction field, select Outgoing, Incoming, or Both.
4. In the Source IP address field, key in the IP address of the network client
whose incoming packets you want to restrict.
5. In the Destination IP address field, key in the IP address of the network
client whose outgoing packets you want to restrict.
6. Click Save to add the IP filter settings to the IP/MAC Filter Listing.
30
DSL-N10S
Chapter 4: Configuring via the web GUI
Configure the SNMP settings
This page allows you to configure the SNMP (Simple Network Management
Protocol) settings.
To configure the SNMP settings:
1. Click Access Management > SNMP tab.
2. Tick Activated to enable SNMP.
3. Key in the trap host.
4. Click Save when done.
Configuring the UPnP settings
The UPnP (Universal Plug and Play) Configuration page allows you to access the
media of the UPnP devices found in your network.
To configure the UPnP settings:
1. Click Access Management > UPnP tab.
2. In the UPnP field, tick Activated to enable UPnP connection.
3. In the Auto-configured field, tick Activated to enable auto-configuration.
4. Click Save to save the settings.
Chapter 4: Configuring via the web GUI
DSL-N10S
31
Configuring the DDNS settings
Setting up DDNS (Dynamic DNS) allows you to access the router from outside
your network through the provided ASUS DDNS Service or another DDNS service.
To configure the DDNS settings:
1. Click Access Management > DDNS tab.
2. In the Dynamic DNS field, tick Activated to enable DDNS connection.
3. Configure the following settings below. When done, click Save.
• My Host Name: Key in the Host Name in the format of xxx.asuscomm.com
(xxx is your host name).
• If you want to use a different DDNS service, fill in the User Name or E-mail
Address and Password.
32
DSL-N10S
Chapter 4: Configuring via the web GUI
Configuring the Maintenance settings
The Maintenance page allows you to restore the wireless router to its default or to
its saved configuration settings, upgrade the firmware, view the system logs and
diagnostics.
Configuring the Administrator settings
The Administrator page allows you to modify the password.
To modify a password:
1. Click Maintenance > Administration tab.
2. Key in your password to the New Password and Confirm Password fields.
3. Click Save to modify the selected user account.
Chapter 4: Configuring via the web GUI
DSL-N10S
33
Upgrading the firmware
The Firmware page allows you to upgrade the wireless router’s firmware version.
NOTE: Download the latest firmware from the ASUS Support site at http://support.asus.com.
To upgrade the firmware:
1. Click Maintenance > Administration tab.
2. In the New Firmware Location field, click Browse to locate the new firmware
file on your computer.
3. Click Upgrade. Wait for a few minutes for the uploading process to complete.
34
DSL-N10S
Chapter 4: Configuring via the web GUI
Restoring the wireless router settings
The SysRestart page allows you to restore the wireless router to its default settings
or to a previously saved configuration settings.
To configure the SysRestart settings:
1. Click Maintenance > SysRestart tab.
2. Select Current Settings or Factory Default Settings.
3. Click Restart to load the selected configuration and reboot the router’s
system.
Chapter 4: Configuring via the web GUI
DSL-N10S
35
Diagnostics
The Diagnostics page allows you to detect and view problems with your network.
36
DSL-N10S
Chapter 4: Configuring via the web GUI
Status
The Status page allows you to view the current status of your wireless router, the
connection status, and the system logs.
Checking your device information and basic settings
Go to Status > Device Info tab to view these information:
• LAN
The LAN field displays some basic LAN settings of the wireless router, the
LAN IP address, Subnet mask and DHCP server status.
•
•
WAN
The WAN field displays the basic status of WAN and DNS server of the router.
ADSL
The ADSL field shows the status of ADSL line, upstream rate, downstream
rate, and other information.
Chapter 4: Configuring via the web GUI
DSL-N10S
37
Viewing the System Log
The System Log page allows you to view the system logs.
To configure the system log:
1. Click Status > System Log tab.
2. Click Save Log to save a copy of logs information to your local drive.
3. Click Clear Log to clear the system logs from the table.
38
DSL-N10S
Chapter 4: Configuring via the web GUI
Setting up the Wi-Fi Protected Setup (WPS)
WPS (Wi-Fi Protected Setup) allows you to set up a secure and protected wireless
network easily.
Note: Ensure that you use a wireless LAN adapter with WPS function.
To enable the WPS function, press the WPS button on your router for more than
four seconds.
Chapter 4: Configuring via the web GUI
DSL-N10S
39
5
Troubleshooting
Troubleshooting
This troubleshooting guide provides solutions to some common problems that
you may encounter while installing or using the ASUS Wireless Router. These
problems require simple troubleshooting that you can perform by yourself. Contact
the ASUS Technical Support if you encounter problems not mentioned in this
chapter.
Problem
The client cannot establish a
wireless connection with the
router.
Action
Out of Range:
• Put the router closer to the wireless client.
• Try to change the channel settings.
Authentication:
• Use wired connection to connect to the
router.
• Check the wireless security settings.
Cannot find the router:
• Insert a pointed blunt object in the Reset
hole at the right side for more than five
seconds.
• Check the setting in the wireless adapter
such as SSID and encryption settings.
Cannot access the Internet
via wireless LAN adapter.
40
• Move the router closer to the wireless client.
• Ensure that the wireless adapter is
connected to the correct wireless router.
• Ensure that the wireless channel in use
conforms to the channels available in your
country/area.
• Check the encryption settings.
• Ensure that the ADSL or Cable connection
is correct.
• Retry using another Ethernet cable.
DSL-N10S Chapter 5: Troubleshooting
Problem
Action
Internet is not accessible.
• Check the status indicators on the ADSL
modem and the wireless router.
• Ensure that the WAN LED on the wireless
router is ON. If the LED is not ON, change
the cable and try again.
When ADSL Modem “Link”
light is ON (not blinking), this
means Internet Access is
possible.
• Restart your computer.
• Refer to the Quick Start Guide of the
wireless router and re-configure the settings.
• Check if the WAN LED on the wireless
router is ON.
• Check the wireless encryption settings.
• Check if the computer can get the IP
address (via both wired network and
wireless network).
• Ensure that your web browser is configured
to use the local LAN, and is not configured
to use a proxy server.
If the ADSL “LINK” light blinks • Ensure that all your cables are all properly
continuously or stays off,
connected .
Internet access is not possible • Disconnect the power cord from the ADSL
- the Router is unable to
or cable modem, wait a few minutes, then
establish a connection with
reconnect the cord.
the ADSL network.
• If the ADSL light continues to blink or stays
OFF, contact your Internet service provider.
Network name or encryption
keys are forgotten.
• Try setting up the wired connection and
configuring the wireless encryption again.
• Insert a pointed blunt object in the Reset
hole at the right side of the wireless router
for more than five seconds.
Chapter 5: Troubleshooting DSL-N10S
41
Problem
How to restore the system to
its default settings?
Action
• Insert a pointed blunt object in the Reset
hole at the right side of the wireless router
for more than five seconds.
• Refer to the section Restoring the wireless
router settings in Chapter 4 of this user
manual.
The following are the factory default settings:
User Name: admin
Password: admin
Enable DHCP: Yes (if WAN cable is plugged in)
IP address: 192.168.1.1
Domain Name: (Blank)
Subnet Mask: 255.255.255.0
DNS Server 1: 192.168.1.1
DNS Server 2: (Blank)
SSID: ASUS
42
DSL-N10S Chapter 5: Troubleshooting
Appendices
Notices
For the following equipment: DSL-N10S
ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest
standards for protecting our environment. We believe in providing solutions for you
to be able to responsibly recycle our products, batteries, other components, as well
as the packaging materials. Please go to http://csr.asus.com/english/Takeback.htm
for the detailed recycling information in different regions.
REACH
Complying with the REACH (Registration, Evaluation, Authorisation, and
Restriction of Chemicals) regulatory framework, we published the chemical
substances in our products at ASUS REACH website at
http://csr.asus.com/english/REACH.htm
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
AppendicesDSL-N10S
43
Prohibition of Co-location
This device and its antenna(s) must not be co-located or operating in conjunction
with any other antenna or transmitter.
Safety Information
To maintain compliance with FCC’s RF exposure guidelines, this equipment should
be installed and operated with minimum distance 20cm between the radiator and
your body. Use on the supplied antenna.
Declaration of Conformity for R&TTE directive 1999/5/EC
Essential requirements – Article 3
Protection requirements for health and safety – Article 3.1a
Testing for electric safety according to EN 60950-1 has been conducted. These are
considered relevant and sufficient.
Protection requirements for electromagnetic compatibility – Article 3.1b
Testing for electromagnetic compatibility according to EN 301 489-1 and EN 301
489-17 has been conducted. These are considered relevant and sufficient.
Effective use of the radio spectrum – Article 3.2
Testing for radio test suites according to EN 300 328- 2 has been conducted.
These are considered relevant and sufficient.
CE Mark Warning
This is a Class B product, in a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
Operation Channels: Ch1~11 for N. America, Ch1~14 Japan, Ch1~13 Europe
(ETSI)
IC Warning
The Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulation.
Cet appareil numerique de la class B respecte toutes les exigences du Reglement
sur le materiel brouilleur du Canada.
44
AppendicesDSL-N10S
GNU General Public License
Licensing information
This product includes copyrighted third-party software licensed under the terms of
the GNU General Public License. Please see The GNU General Public License
for the exact terms and conditions of this license. We include a copy of the GPL
with every CD shipped with our product. All future firmware updates will also
be accompanied with their respective source code. Please visit our web site for
updated information. Note that we do not offer direct support for the distribution.
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.
59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
Everyone is permitted to copy and distribute verbatim copies of this license
document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to
share and change it. By contrast, the GNU General Public License is intended
to guarantee your freedom to share and change free software--to make sure the
software is free for all its users. This General Public License applies to most of the
Free Software Foundation’s software and to any other program whose authors
commit to using it. (Some other Free Software Foundation software is covered
by the GNU Library General Public License instead.) You can apply it to your
programs, too.
When we speak of free software, we are referring to freedom, not price. Our
General Public Licenses are designed to make sure that you have the freedom to
distribute copies of free software (and charge for this service if you wish), that you
receive source code or can get it if you want it, that you can change the software or
use pieces of it in new free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny
you these rights or to ask you to surrender the rights. These restrictions translate
to certain responsibilities for you if you distribute copies of the software, or if you
modify it.
For example, if you distribute copies of such a program, whether gratis or for a
fee, you must give the recipients all the rights that you have. You must make sure
that they, too, receive or can get the source code. And you must show them these
terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you
this license which gives you legal permission to copy, distribute and/or modify the
software.
AppendicesDSL-N10S
45
Also, for each author’s protection and ours, we want to make certain that everyone
understands that there is no warranty for this free software. If the software is
modified by someone else and passed on, we want its recipients to know that what
they have is not the original, so that any problems introduced by others will not
reflect on the original authors’ reputations.
Finally, any free program is threatened constantly by software patents. We wish to
avoid the danger that redistributors of a free program will individually obtain patent
licenses, in effect making the program proprietary. To prevent this, we have made it
clear that any patent must be licensed for everyone’s free use or not licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
Terms & conditions for copying, distribution, & modification
0. This License applies to any program or other work which contains a notice
placed by the copyright holder saying it may be distributed under the terms of
this General Public License. The “Program”, below, refers to any such program
or work, and a “work based on the Program” means either the Program or
any derivative work under copyright law: that is to say, a work containing
the Program or a portion of it, either verbatim or with modifications and/or
translated into another language. (Hereinafter, translation is included without
limitation in the term “modification”.) Each licensee is addressed as “you”.
Activities other than copying, distribution and modification are not covered
by this License; they are outside its scope. The act of running the Program is
not restricted, and the output from the Program is covered only if its contents
constitute a work based on the Program (independent of having been made by
running the Program). Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program’s source code
as you receive it, in any medium, provided that you conspicuously and
appropriately publish on each copy an appropriate copyright notice and
disclaimer of warranty; keep intact all the notices that refer to this License and
to the absence of any warranty; and give any other recipients of the Program a
copy of this License along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may
at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it,
thus forming a work based on the Program, and copy and distribute such
modifications or work under the terms of Section 1 above, provided that you
also meet all of these conditions:
a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.
46
AppendicesDSL-N10S
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed
as a whole at no charge to all third parties under the terms of this License.
c) If the modified program normally reads commands interactively when run,
you must cause it, when started running for such interactive use in the most
ordinary way, to print or display an announcement including an appropriate
copyright notice and a notice that there is no warranty (or else, saying that
you provide a warranty) and that users may redistribute the program under
these conditions, and telling the user how to view a copy of this License.
(Exception: if the Program itself is interactive but does not normally print such
an announcement, your work based on the Program is not required to print an
announcement.)
These requirements apply to the modified work as a whole. If identifiable
sections of that work are not derived from the Program, and can be reasonably
considered independent and separate works in themselves, then this License,
and its terms, do not apply to those sections when you distribute them as
separate works. But when you distribute the same sections as part of a whole
which is a work based on the Program, the distribution of the whole must be on
the terms of this License, whose permissions for other licensees extend to the
entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to
work written entirely by you; rather, the intent is to exercise the right to control
the distribution of derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with
the Program (or with a work based on the Program) on a volume of a storage
or distribution medium does not bring the other work under the scope of this
License.
3. You may copy and distribute the Program (or a work based on it, under Section
2) in object code or executable form under the terms of Sections 1 and 2 above
provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable source
code, which must be distributed under the terms of Sections 1 and 2 above on
a medium customarily used for software interchange; or,
b) Accompany it with a written offer, valid for at least three years, to give any
third party, for a charge no more than your cost of physically performing source
distribution, a complete machine-readable copy of the corresponding source
code, to be distributed under the terms of Sections 1 and 2 above on a medium
customarily used for software interchange; or,
c) Accompany it with the information you received as to the offer to distribute
corresponding source code. (This alternative is allowed only for noncommercial
distribution and only if you received the program in object code or executable
form with such an offer, in accord with Subsection b above.)
The source code for a work means the preferred form of the work for making
modifications to it. For an executable work, complete source code means
all the source code for all modules it contains, plus any associated interface
AppendicesDSL-N10S
47
definition files, plus the scripts used to control compilation and installation of
the executable. However, as a special exception, the source code distributed
need not include anything that is normally distributed (in either source or
binary form) with the major components (compiler, kernel, and so on) of the
operating system on which the executable runs, unless that component itself
accompanies the executable.
If distribution of executable or object code is made by offering access to copy
from a designated place, then offering equivalent access to copy the source
code from the same place counts as distribution of the source code, even
though third parties are not compelled to copy the source along with the object
code.
4. You may not copy, modify, sublicense, or distribute the Program except as
expressly provided under this License. Any attempt otherwise to copy, modify,
sublicense or distribute the Program is void, and will automatically terminate
your rights under this License. However, parties who have received copies, or
rights, from you under this License will not have their licenses terminated so
long as such parties remain in full compliance.
5. You are not required to accept this License, since you have not signed it.
However, nothing else grants you permission to modify or distribute the
Program or its derivative works. These actions are prohibited by law if you do
not accept this License. Therefore, by modifying or distributing the Program (or
any work based on the Program), you indicate your acceptance of this License
to do so, and all its terms and conditions for copying, distributing or modifying
the Program or works based on it.
6. Each time you redistribute the Program (or any work based on the Program),
the recipient automatically receives a license from the original licensor to
copy, distribute or modify the Program subject to these terms and conditions.
You may not impose any further restrictions on the recipients’ exercise of the
rights granted herein. You are not responsible for enforcing compliance by third
parties to this License.
7. If, as a consequence of a court judgment or allegation of patent infringement
or for any other reason (not limited to patent issues), conditions are imposed
on you (whether by court order, agreement or otherwise) that contradict the
conditions of this License, they do not excuse you from the conditions of this
License. If you cannot distribute so as to satisfy simultaneously your obligations
under this License and any other pertinent obligations, then as a consequence
you may not distribute the Program at all. For example, if a patent license
would not permit royalty-free redistribution of the Program by all those who
receive copies directly or indirectly through you, then the only way you could
satisfy both it and this License would be to refrain entirely from distribution of
the Program.
If any portion of this section is held invalid or unenforceable under any
particular circumstance, the balance of the section is intended to apply and the
section as a whole is intended to apply in other circumstances.
48
AppendicesDSL-N10S
It is not the purpose of this section to induce you to infringe any patents or
other property right claims or to contest validity of any such claims; this section
has the sole purpose of protecting the integrity of the free software distribution
system, which is implemented by public license practices. Many people have
made generous contributions to the wide range of software distributed through
that system in reliance on consistent application of that system; it is up to the
author/donor to decide if he or she is willing to distribute software through any
other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a
consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries
either by patents or by copyrighted interfaces, the original copyright holder
who places the Program under this License may add an explicit geographical
distribution limitation excluding those countries, so that distribution is permitted
only in or among countries not thus excluded. In such case, this License
incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the
General Public License from time to time. Such new versions will be similar in
spirit to the present version, but may differ in detail to address new problems or
concerns.
Each version is given a distinguishing version number. If the Program specifies
a version number of this License which applies to it and “any later version”, you
have the option of following the terms and conditions either of that version or
of any later version published by the Free Software Foundation. If the Program
does not specify a version number of this License, you may choose any version
ever published by the Free Software Foundation.
10. If you wish to incorporate parts of the Program into other free programs whose
distribution conditions are different, write to the author to ask for permission.
For software which is copyrighted by the Free Software Foundation, write to
the Free Software Foundation; we sometimes make exceptions for this. Our
decision will be guided by the two goals of preserving the free status of all
derivatives of our free software and of promoting the sharing and reuse of
software generally.
NO WARRANTY
11 BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS
NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY
APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING
THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE
THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY
AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE
AppendicesDSL-N10S
49
PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL
NECESSARY SERVICING, REPAIR OR CORRECTION.
12 IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED
TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER
PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS
PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING
ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM
(INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING
RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD
PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY
OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
DGT Warning
Safety Warning
SAFE TEMP: This wireless router should be only used in environments with
ambient temperatures between 5ºC(41ºF) and 40ºC(104ºF).
DO NOT expose to or use near liquids, rain, or moisture. DO NOT use the modem
during electrical storms.
50
AppendicesDSL-N10S
For Turkey only
Authorised distributors in Turkey:
BOGAZICI BIL GISAYAR SAN. VE TIC. A.S.
Tel. No.:
+90 212 3311000
Address:
AYAZAGA MAH. KEMERBURGAZ CAD. NO.10
AYAZAGA/ISTANBUL
CIZGI Elektronik San. Tic. Ltd. Sti.
Tel. No.:
+90 212 3567070
Address:
CEMAL SURURI CD. HALIM MERIC IS MERKEZI
No: 15/C D:5-6 34394 MECIDIYEKOY/ISTANBUL
KOYUNCU ELEKTRONiK BiLGi iSLEM SiST. SAN. VE DIS TIC. A.S.
Tel. No.:
+90 216 5288888
Address:
EMEK MAH.ORDU CAD. NO:18, SARIGAZi,
SANCAKTEPE ISTANBUL
AEEE Yönetmeliğine Uygundur.
AppendicesDSL-N10S
51
ASUS Contact Information
ASUSTeK COMPUTER INC. (Asia Pacific)
Address
15 Li-Te Road, Peitou, Taipei, Taiwan 11259
Websitewww.asus.com.tw
Technical Support
Telephone+886228943447
Support Fax
+886228907698
Online support
support.asus.com
ASUS COMPUTER INTERNATIONAL (America)
Address
800 Corporate Way, Fremont, CA 94539, USA
Telephone+15107393777
Fax
+15106084555
Websiteusa.asus.com
Online support
support.asus.com
ASUS COMPUTER GmbH (Germany and Austria)
Address
Harkort Str. 21-23, D-40880 Ratingen, Germany
Support Fax
+49-2102-959931
Websiteasus.com/de
Online contact
eu-rma.asus.com/sales
Technical Support
Telephone (Component)
Telephone Germany
(System/Notebook/Eee/LCD)
Telephone Austria
(System/Notebook/Eee/LCD)
Support Fax
Online support
52
+49-2102-5789555
+49-2102-5789557
+43-820-240513
+49-2102-959911
support.asus.com
AppendicesDSL-N10S
Networks Global Hotline Information
Region
Country
Hotline Number
Service Hours
09:00-13:00 ;
14:00-18:00 Mon-Fri
09:00-18:00 Mon-Fri
Cyprus
800-92491
France
0033-170949400
0049-1805010920
09:00-18:00 Mon-Fri
0049-1805010923
(component support)
10:00-17:00 Mon-Fri
0049-2102959911 ( Fax )
0036-15054561
09:00-17:30 Mon-Fri
09:00-13:00 ;
199-400089
14:00-18:00 Mon-Fri
09:00-13:00 ;
00800-44142044
14:00-18:00 Mon-Fri
0043-820240513
09:00-18:00 Mon-Fri
Germany
Hungary
Italy
Greece
Austria
Netherlands/
Luxembourg
Belgium
Europe Norway
Sweden
Finland
Denmark
Poland
Spain
Portugal
Slovak Republic
Czech Republic
Switzerland-German
Switzerland-French
Switzerland-Italian
United Kingdom
Ireland
Russia and CIS
Ukraine
0031-591570290
09:00-17:00 Mon-Fri
0032-78150231
0047-2316-2682
0046-858769407
00358-969379690
0045-38322943
0048-225718040
0034-902889688
00351-707500310
00421-232162621
00420-596766888
0041-848111010
0041-848111014
0041-848111012
0044-8448008340
0035-31890719918
008-800-100-ASUS
0038-0445457727
09:00-17:00 Mon-Fri
09:00-18:00 Mon-Fri
09:00-18:00 Mon-Fri
10:00-19:00 Mon-Fri
09:00-18:00 Mon-Fri
08:30-17:30 Mon-Fri
09:00-18:00 Mon-Fri
09:00-18:00 Mon-Fri
08:00-17:00 Mon-Fri
08:00-17:00 Mon-Fri
09:00-18:00 Mon-Fri
09:00-18:00 Mon-Fri
09:00-18:00 Mon-Fri
09:00-17:00 Mon-Fri
09:00-17:00 Mon-Fri
09:00-18:00 Mon-Fri
09:00-18:00 Mon-Fri
AppendicesDSL-N10S
53
Networks Global Hotline Information
Region
Country
Australia
New Zealand
Japan
Korea
Thailand
Singapore
Asia-Pacific
Malaysia
Philippine
India
India(WL/NW)
Indonesia
Americas
54
Hotline Numbers
1300-278788
0800-278788
0800-1232787
0081-473905630
( Non-Toll Free )
0082-215666868
0066-24011717
1800-8525201
0065-64157917
0065-67203835
( Repair Status Only )
0060-320535077
1800-18550163
1800-2090365
0062-2129495000
500128 (Local Only)
Vietnam
1900-555581
Hong Kong
USA
Canada
Mexico
00852-35824770
1-812-282-2787
001-8008367847
Service Hours
09:00-18:00 Mon-Fri
09:00-18:00 Mon-Fri
09:00-18:00 Mon-Fri
09:00-17:00 Sat-Sun
09:00-18:00 Mon-Fri
09:00-17:00 Sat-Sun
09:30-17:00 Mon-Fri
09:00-18:00 Mon-Fri
11:00-19:00 Mon-Fri
11:00-19:00 Mon-Fri
11:00-13:00 Sat
10:00-19:00 Mon-Fri
09:00-18:00 Mon-Fri
09:00-18:00 Mon-Sat
09:00-21:00 Mon-Sun
09:30-17:00 Mon-Fri
9:30 – 12:00 Sat
08:00-12:00
13:30-17:30 Mon-Sat
10:00-19:00 Mon-Sat
8:30-12:00 EST Mon-Fri
9:00-18:00 EST Sat-Sun
08:00-20:00 CST Mon-Fri
08:00-15:00 CST Sat
AppendicesDSL-N10S
Networks Global Hotline Information
Region
Middle
East +
Africa
Country
Egypt
Saudi Arabia
UAE
Turkey
South Africa
Israel
Romania
Bosnia
Herzegovina
Bulgaria
Hotline Numbers
800-2787349
800-1212787
00971-42958941
0090-2165243000
0861-278772
*6557/00972-39142800
*9770/00972-35598555
0040-213301786
Service Hours
09:00-18:00 Sun-Thu
09:00-18:00 Sat-Wed
09:00-18:00 Sun-Thu
09:00-18:00 Mon-Fri
08:00-17:00 Mon-Fri
08:00-17:00 Sun-Thu
08:30-17:30 Sun-Thu
09:00-18:30 Mon-Fri
00387-33773163
09:00-17:00 Mon-Fri
00359-70014411
00359-29889170
00385-16401111
00382-20608251
00381-112070677
00368-59045400
00368-59045401
Estonia
00372-6671796
Latvia
00371-67408838
Lithuania-Kaunas 00370-37329000
Lithuania-Vilnius 00370-522101160
Balkan
Countries Croatia
Montenegro
Serbia
Slovenia
09:30-18:30 Mon-Fri
09:30-18:00 Mon-Fri
09:00-17:00 Mon-Fri
09:00-17:00 Mon-Fri
09:00-17:00 Mon-Fri
08:00-16:00 Mon-Fri
09:00-18:00 Mon-Fri
09:00-18:00 Mon-Fri
09:00-18:00 Mon-Fri
09:00-18:00 Mon-Fri
NOTE:
For more information, visit the ASUS support site at:
http://support.asus.com
Manufacturer:
ASUSTeK Computer Inc.
Tel:
+886-2-2894-3447
Address:
4F, No. 150, LI-TE RD., PEITOU,
TAIPEI 112, TAIWAN
Authorised representative ASUS Computer GmbH
in Europe:
Address:
HARKORT STR. 21-23, 40880
RATINGEN, GERMANY
AppendicesDSL-N10S
55
Download PDF