Miele | T1526 | Operating instructions | Miele T1526 Operating instructions

Operations Manual
for the T 1526
Vented Dryer
It is essential to read these
operating instructions before
installing or using the machine to avoid
the risk of accident, or damage
to the machine.
]
M.-Nr. 05 017 940
Contents
Contents
Guide to the machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Your contribution to the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Loading and unloading the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Notes on laundry care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Program selection
Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To select a program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To change a program during drying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Correct procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
After the program has finished. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
11
11
11
11
Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Problem solving guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
After-sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
INSTALLATION INSTRUCTIONS
Grounding and Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Installation - venting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Consumption data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
2
Guide to the machine
Guide to the machine
1
2
3
4
5
Supply cable with plug
Control panel
Drum door
Exhaust connection (left or rear)
Four height-adjustable legs
3
Guide to the machine
Pushbuttons
Indicator lamps
– Door
This button is used to open the door
(does not stay pushed in).
– PROGRAM SEQUENCE
The program sequence indicator
lamps show the current state of the
drying program.
– j ON / k OFF
When the machine is turned on, the
“On” indicator will light up if the door is
closed. If the door is open, the drum
light will be on.
– Buzzer
Allows the buzzer to sound when the
drum rotates during the anti-crease
cycle.
– Low temp.
Lower drying temperatures for delicate fabrics, e.g. acrylics (symbol r).
– Start
Starts the selected program (does
not stay pushed in).
– DRYING STAGE REACHED
These indicator lamps show which
drying stage the program has
reached. For program stages “Normal” and “Extra dry” the indicator
lamp remains at the “Normal” position.
PROGRAM SETTING-SELECTOR
Set the required program by turning the
knob either clockwise or counterclockwise.
– COTTONS
– PERMANENT PRESS
– TIMED DRYING
Items can be either dried for 20
minutes (incl. a cooling-down phase)
or cool air fluffed for 15 minutes.
4
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
WARNING - To reduce the risk of fire,
electrical shock, or injury to persons
when using your appliance, follow
basic precautions, including the following:
1. Read these operating instructions before using your dryer for the first
time, as this is for your own safety
and for the protection of your machine.
2. Remember to remove the door when
disposing of an old machine to prevent children from accidently locking
themselves in the machine and endangering their lives.
3. Do not install or store this appliance
where it will be exposed to the
weather.
4. Do not install your dryer in rooms
where freezing temperatures may
occur. The reliability of the electronic
control system may be impaired.
5. This machine should only be used for
drying the following fabrics:
7. Clean the lint filter before and after
each load.
8. Do not dry articles that have been
previously cleaned in, washed in,
soaked in, or spotted with gasoline,
dry-cleaning solvents, other flammable or explosive substances as they
give off vapors that could ignite or
explode.
9. Do not allow children to play on or in
the appliance. Close supervision of
children is necessary when the appliance is used near the children.
10.To avoid back-pressure or accumulation of exhaust fumes, provide adequate room ventilation, by means of
permanent vents or an open window.
11.Always close the door after use to
prevent children from leaning on the
door and causing the dryer to tilt.
12.Keep area around the exhaust opening and adjacent surrounding areas
free from accumulation of lint, dust
and dirt.
– Items which can be machine dried
as specified by the laundry care
label.
– Items which have been washed in
water.
6. The following fabrics pose a fire hazard:
– Items which contain foam rubber,
rubber or rubberlike components.
– Items which have been treated with
inflammable cleaning agents, such
as gasoline or dry-cleaning solvents.
– Items containing hair lacquer, hairspray, nail polish remover or similar
substances.
5
IMPORTANT SAFETY INSTRUCTIONS
13.The interior of the machine and exhaust duct should be cleaned periodically by qualified personnel.
14.Do not reach into the dryer if the
drum is moving.
15.Do not tamper with controls.
16.Do not repair or place any part of the
appliance or attempt any servicing
unless specifically recommended in
the user maintenance instruction or
in published user repair instructions
that you understand and have the
skills to carry out.
Repairs to electrical appliances
should only carried out by qualified
personnel.
Incorrectly repaired machines may
pose a considerable risk to the user.
17.Formation of lint.
Lint is principally the result of friction
when items are worn and washed.
Machine-drying hardly causes any
lint to form and, as has been established by reseach institutes, has no
effect on the lifetime of fabrics.
18.Warning - Do not use fabric softener/anti static dryer sheets.
Residues from these products blockup (clog) the lint filter causing premature failure of the dryer.
Miele dryers are designed to dry
laundry without static cling. However, should fabric softener be required, use liquid fabric softener in
the wash cycle.
Clean lint filter mesh monthly by washing/scrubbing with hot soap and
water.
6
19.Do not place items exposed to cooking oils in your dryer. Items contaimed with cooking oils may contribute to a chemical reaction that could
cause a load to catch fire.
SAVE THESE INSTRUCTIONS
For grounding and electrical connection instructions, refer to the electrical connection section.
Your contribution to the environment
Your contribution to the environment
Disposal of the packing material.
The transport and protective packing is
mostly manufactured from the following
recycled or re-useable materials:
– corrugated paper/cardboard
Disposal of your old machine.
Old machines contain materials which
can be recycled. Please contact your
recycling center or scrap merchant
and render the machine inoperative as
per the “Important Safety Instructions”
before disposing of the appliance.
– polystyrene - CFC-free
– polyethylene foil (transparent)
– untreated wood
– fiber board
Please check local environmental regulations before disposing of packing materials and discarding the appliance.
7
Loading and unloading the machine
Loading and unloading the machine
WARNING - To reduce the risk of fire,
electric shock, or injury to persons,
read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.
Load the laundry loosely into the
drum.
Duvet covers and pillowcases
should be fastened before drying in
order to prevent small items from rolling inside of them.
If the wash is not removed at the end
of the drying program, the machine
will automatically enter the anticrease cycle for 60 minutes. This entails the drum being rotated at short
intervals in order to reduce the formation of creases.
Once the laundry has been
removed, check that the drum is
empty. Any items left in the drum
could be damaged through overdrying during the next program.
Clean the lint filter after each drying
cycle to prevent excessive energy
consumption, longer program times
and the risk of fire.
The door should always be closed
after use.
Important: Check that laundry cannot be trapped by the door as this
may cause damage to the fabric.
8
Notes on laundry care
Notes on laundry care
Before drying, check the instructions
on the fabric care label.
The following fabrics should not be
dried in a tumble dryer:
– Woollens and wool blends
These fabrics tend to become matted
and shrink.
– Items filled with down
The fine fabric interior tends to shrink,
depending on the quality of the item
involved.
– Pure linen
These items should only be machinedried if specified as suitable by the
manufacturer on the textile care label.
The surface of the fabric may otherwise tend to become “rough”.
Miele dryers have been designed to
dry laundry free of static cling, without
the use of dryer softener sheets or similar products. The dryer continuously
monitors the moisture content of the
laundry, and automatically shuts off the
heat when the selected degree of dryness is reached. Through the use of a
cool down period, (where the machine
operates without heat), cool, static free
laundry is the end result. Dryer softener
sheets perform the same function by
depositing a chemical residue on both
the clothes and the interior of the dryer.
Over time, this coating may lead to performance reductions in the dryer.
Notes:
Knitted fabrics and flannel sheets tend
to shrink when washed for the first time
and also when dried. They should not
be overdried (Extra dry)!
Starched laundry can also be dried in
the tumble dryer.
Permanent press items should be
briefly spun in the washing machine before drying. Items which are prone to
creasing should not be dried in the
“PERMANENT PRESS- Normal +” - Program.
Drip-dry shirts made of pure cotton
may tend to crease, depending on the
quality of their finish.
These items should be dried in a
“Hand iron”program.
Permanent press fabrics tend to crease
more as the size of the load increases.
This is particularly true of very delicate
fabrics. The load should be reduced to
2 kg or, if necessary, to 1.5 kg.
Do not dry new dark-colored fabrics
together with light-colored items as
they may discolor.
If fabric softening is desired, it is more
convenient, economical and beneficial to
the clothing if a liquid softener is automatically dispensed while the clothes are
in the washing machine. Please see the
washing machine operating instructions
for directions on how to automatically dispense a liquid softener.
9
Program selection
Program selection
Functional description
An electronic sensor system monitors
the moisture content of the laundry.
Once the required degree of dryness is
reached, cold air enters the drum to
cool the laundry.
The drying program is then terminated.
Function of the pushbuttons
– Low temp.
When selected the machines lower
drying temperatures for delicate fabrics, (e.g. acrylics, nylon).
– Start
Starts the selected program.
“PROGRAM SEQUENCE”
indicators
The program sequence indicator lamps
show the current status of the drying
program.
“DRYING STAGE REACHED”
indicators
This indicator shows which drying
stage the program has reached.
“PROGRAM SETTING” selector
– Door
This button is used to open the door.
– ON/OFF
When the machine is turned on, the
“On” indicator lamp lights if the door is
closed. When the door is open, the
drum is illuminated.
– Buzzer
When depressed, the buzzer will
sound as the drum rotates during the
anticrease cycle.
10
There is a range of settings for both
"Cottons" and "Permanent Press".
In addition, items can be either dried
for 20 minutes (incl. a cooling-cycle
lasting 8 mins.) or fluffed in cool air for
15 minutes.
Program selection
To select a program
Press the "On/Off" button.
To change a program during
drying
Set the program selector to the
desired program.
The new program will start from the beginning.
The tables on the following pages list
the range of applications for the different programs.
Set the desired program by turning
the program selector either clockwise or counterclockwise.
Press the "Start" button.
The program status will be stored for
30 minutes in the event of a power
failure.
The program is canceled if:
– There is a power failure lasting more
than 30 minutes.
– The door is opened after the machine has entered the "Cooling
down" or "Anti-crease" stage.
Correct procedure
1 Press the "On/Off" button.
2 Press the "Door" button.
3 Open the door and load the machine.
4 Close the door with a firm swing - do
not push it shut.
5 If drying delicate fabrics, press the
"Low temp." button.
6 Select the "Buzzer" if so desired.
7 Select a program.
8 Press the "Start" button.
After the program has finished
1 Set the program selector to "Finish".
2 Remove the laundry.
3 Clean the lint filter.
4 Turn off the machine.
11
Programs
Programs
Drying stage
Type of laundry/fabric
Max. load
Special instructions
Multi-layer fabrics, mixed
loads of cotton fabrics,
e.g.jeans, towels,
sweatsuits.
Uniform loads of cotton
fabrics e.g. flannel items,
underwear, socks.
6 kg
The “Extra dry” program
should not be selected for
jersey wear items or items
that may shrink.
If items are still damp,
select the “Extra dry”
program.
Normal-
Knitted cotton fabrics
susceptible to shrinkage,
e.g. jersey wear or
lightweight cotton fabrics.
6 kg
If items are still damp,
select the “Normal“
program.
Hand iron r
Hand iron rr
Cotton or linen fabrics, to
be left damp for easier
ironing.
6 kg
Machine iron
Cotton or linen fabrics,
including starched laundry,
to be ironed on the rotary
iron, (B865E).
6 kg
Moisture can be increased
or decreased by using
“Hand iron rr” or “Hand
iron r” respectively.
The laundry can be loosely
rolled to prevent it from
drying out until it can be
ironed.
COTTONS
Extra dry
Normal
12
6 kg
Programs
Drying stage
Type of laundry/fabric
Max. load
Special instructions
Permanent press items
made of synthetic or
blended fabrics, e.g.
pullovers, dresses, pants,
etc., which are not dried
adequately in the “Normal”
program.
Permanent press shirts,
table cloths, bedding etc.
made of blended woven or
knitted fabrics, e.g.
cotton/synthetic.
3 kg
With blended fabrics
consisting of wool and
synthetics, consult the
manufacturer’s instructions,
as the wool component
may cause the fabric to
matt and shrink.
PERMANENT PRESS
Normal +
Normal
3 kg
Permanent press shirts,
table cloths, pillowcases
etc. cotton/synthetics,
which are to be pressed.
3 kg
warm
Individual items, e.g.
comforters, or very small
loads.
-
This cycle will run for the
full 20 minutes, even if the
clothes are dry sooner.
cool air
Items which you want to
"fluff".
6 kg
-
Hand iron
TIMED DRYING
13
Cleaning and care
Cleaning and care
Cleaning the lint filter
The lint is collected by the lint filter in
the door.
Clean the filter after every program.
Grip the filter by the recessed
handle and pull up to remove.
Cleaning the dryer
Before cleaning the tumble dryer;
disconnect the machine from the
power supply.
The dryer can be cleaned using
soapy water or a mild detergent (not
scouring powder) and dried with a
soft cloth.
The drum may be cleaned using a
suitable stainless steel cleaner following the manufacturer’s instructions.
The machine must never be hosed
down. Do not use any abrasive substances or scouring pads to clean
the machine.
Any remaining lint in the hollow part
of the door can be removed through
the gap at the bottom.
The lint filter can be rinsed with water if
necessary.
Dry the lint filter before putting it
back in place.
14
Problem solving guide
Problem solving guide
Electrical appliances should only be repaired by qualified personnel. Incorrectly repaired machines may put the user at risk. There are, however, minor
problems which can be corrected without contacting the Service Department.
What to do if, . . . ?
Cause . . .
Remedy . . .
. . . the tumble dryer fails to
start when turned on?
Check whether the “On”
indicator lights up. If so, failure
to start may be due to an
incorrect program selection
procedure.
Repeat the switch-on procedure
in the correct sequence, as
outlined in the “Program
Selection” chapter.
If the “On” indicator lamp does
not illuminate, check that:
– The “ON/OFF” button is
depressed.
– The door is properly closed.
– The machine is plugged in
and the fuse or circuit breaker
has not tripped.
Select a longer drying program.
. . . the laundry is not sufficiently dry?
. . . the drying times are too
long?
. . . the “anti-crease” indicator
lamp in the sequence indicator display starts flashing?
The load consists of dissimilar
items (size and fabrics).
Small loads or individual items
may cause the program to
terminate the cycle prematurely.
Small loads can be time-dried.
The lint filter is clogged.
Clean the lint filter in the door.
The laundry was not spun in the
washer for a sufficient time.
Make sure that the laundry is
thoroughly spun before drying.
– Turn the program selector
to “finish”.
– Turn the machine off and
then on again.
– Select a program.
– Press the “Start” button.
If the indicator lamp starts
flashing again, this indicates a
fault in the machine.
Please contact the Miele
Service Dept.
15
Problem solving guide
What to do if, . . . ?
. . . the drum door opens during the drying cycle?
. . . the interior drum light fails
to function?
. . . you have to open the door
in the event of a power
failure?
16
Cause . . .
The machine has overheated.
The temperature limiter opened
the drum door and caused the
machine to turn off
automatically.
Possible reasons for
overheating:
– The lint filter in the door is
clogged.
– The vent duct is blocked.
– The vent aperture (e.g.
louvred window vent, wall
vent) is blocked.
Remedy . . .
It only lights up when the
machine is switched on. The
bulb may be burnt out.
See next page.
Before restarting the program,
proceed as follows:
– Release the ON/OFF button.
– Clean the affected part of the
machine.
– Turn on the machine again.
– Reselect the terminated
program.
– Press the “Start” button.
If the drum door opens again,
the Miele Service Dept. should
be contacted.
See next page.
Problem solving guide
The interior drum light fails to function: The bulb may be burnt out.
To open the door in the event of a
power failure
Replace it as follows:
Turn off the machine or disconnect
it from the power supply.
Open the door.
Pull forward on the un-hinged side of
the door.
Unscrew the plastic bulb cover located inside the drum and above the
door (see illustration).
The light bulb must not exceed the
maximum wattage quoted on the
data plate.
Replace the bulb and the plastic
cover.
The cover must be correctly installed
and tightened, otherwise moisture may
seep in and cause the socket to corrode.
This is a temperature-resistant bulb
and should only be ordered from your
Miele Service Dept.
17
After-sales service
After-sales service
In the event of problems which cannot
be solved, please contact:
– Your Miele Dealer
– The nearest Miele Service Department (see back cover for the adress).
When contacting the Service Department, please quote the Model and Serial numbers of your appliance, both of
which can be found on the right side
after the door is opened.
Specimen:
18
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
Grounding and Electrical connection
Grounding instructions
This appliance must be grounded.
In the event of a malfunction, grounding will reduce the risk of electric shock
by providing a path of least resistance
for the electric current. This appliance
is equipped with a cord having an
equipment grounding conductor and a
grounding plug. The plug must be
plugged into an appropriate outlet that
is properly installed and grounded in
accordance with all local codes and ordinances.
Warning
Improper connection of the equipment-grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or
serviceman if you are in doubt as to
whether the appliance is properly
grounded.
Do not modify the plug provided
with the appliance; if it will not fit the
outlet, have a proper outlet installed
by a qualified electrician.
Electrical connection
This installation should be done by an
experienced and qualified person, in
most cases a licensed electrician, in accordance with local codes and regulations.
This dryer is supplied with a 1.5 m power
cord with a 3-pole, 4 wire grounding plug,
14-30P (regular Canadian dryer plug).
This plug has to be plugged into a 3-pole,
4 wire grounding receptacle, 14-30R
(regular Canadian dryer receptacle).
The receptacle has to be connected to
Line 1, Line 2, Neutral and Ground wires.
The voltage is 120/240 V AC or 120/208 V AC.
“EASY INSTALLATION KIT”
If you do not have a designated line,
4 wire, 120/240 V – 15 or 30 Amps, for
this appliance, but you have the 4 wire,
120/(208)240 V – 30 Amp Canadian
dryer wall receptacle (14-30 R) you can
use the Miele Double Receptacle Box.
This consists of two standard receptacles 14-30 R, 4 fuses, box and plug
cord, which allows you to use that
single dryer wall receptacle to supply
power to a Miele washer and Miele
dryer. Both machines may operate at
the same time because each uses
maximum about 15 A current.
For more information on the electrical
connection on the Miele Double Receptacle Box please contact:
– your Miele dealer
– the nearest Miele Service Department.
19
INSTALLATION INSTRUCTIONS
Installation
Turn the counternuts up and tighten
against the bottom.
A gap of 10 mm must be maintained between the bottom of machine and the floor. This gap must
not be blocked by deep pile carpet,
plinths etc., as this will prevent a sufficient intake of cold air.
Where to install the machine
The space required by the vent
duct should be taken into consideration when calculating the distance
between the machine and a wall or
other appliances.
The machine should be level to ensure
safe and proper operation. Minor discrepancies do not, however, have an
adverse effect on operation.
The tumble dryer can also be placed
on top of a Miele washing machine (capacity 6 kg) for a stacked installation.
An appropriate stacking kit is required
and can be obtained from your Miele
dealer, or the Miele Parts Dept.
The machine can be leveled by turning the legs clockwise or counterclockwise as necessary.
20
INSTALLATION INSTRUCTIONS
Exhaust venting
The moist air from the dryer must be
vented to the outside.
Installing the connector on the left
side of the machine
Remove the cap covering the exhaust part as follows:
The appliance should not be vented
into a chimney, a wall, a ceiling, or
any concealed spaces of the building.
When installing, try to avoid:
– very long venting systems
– too many bends or angles
– tight corners
otherwise . . .
. . . the drying results will be affected,
. . . drying will take longer and use more
energy.
Materials suitable for venting:
– rigid metal pipe
– flexible metal pipe
Install the venting in such a way that
the expelled air cannot be drawn
back into the machine.
– Insert a thin screwdriver into the slot
by the retaining hook. Press the hook
gently upwards.
At the same time turn the cap
counterclockwise.
Do not vent the dryer into a flue
used by gas or fuel boilers or
heaters.
A vent connector is included with the
machine. It should be pressed into the
vent outlet and will simplify the connection of the exhaust pipe.
Before installation, disconnect the
tumble dryer from the electrical supply (unplug from the wall socket, or
turn off the circuit breaker.
Installation at the rear
The machine comes supplied with
the connector installed on the rear
exhaust port.
In the same way remove the vent
socket from the rear exhaust port.
Secure into the side port by pressing
it in and turning it clockwise.
Seal the rear exhaust port using the
cap.
21
INSTALLATION INSTRUCTIONS
The shorter the exhaust ductwork, the
more efficient the dryer will be. Expelled air is slowed down in the ducts
due to friction against the inner walls,
therefore the shorter and smoother the
inner walls are, the less friction will
occur.
An elbow or bend creates more friction
than a straight duct. An additional duct
length factor must therefore be added
for each elbow or bend (see Table I).
This factor expresses the resistance of
the bend in terms of a straight length of
duct.
The additional length factor is then
added to the measured duct length to
give the effective duct length.
A larger duct diameter also helps to reduce friction. The duct diameter should
therefore be increased with increasing
duct length.
To calculate the effective duct length.
Measure the actual duct length.
Establish the number of elbows or
bends necessary, noting the type of
bend, angle and radius involved
(see Table I).
Add the additional length factor as
specified in Table I to the actual duct
length to give the effective duct
length.
The necessary duct diameter should
then be found in Table II.
Note:
Drying times and energy consumption
remain unaltered for 100 mm duct up to
a total length of 8 m.
Longer duct may lead to slight increases in drying times and energy
consumption but will not impair the
function of the machine as long as the
necessary duct diameter is used (see
Table II).
Tabel I
Type of bend
Flexible metal piping
Plain piping
Elbow
Concertina bend
Wall vent kit with louvres, or window vent kit
Wall vent kit with flap, or window vent kit
Exhaust connection, left side
22
Angle
Radius in mm
90°
90°
45°
90°
100-300
300-500
100-500
100
90°
200
Additional duct
length in m
0.5
0.3
0.3
0.35
2.3
0.7
3.6
1.25
4,9
INSTALLATION INSTRUCTIONS
Table II
Effective duct
length (m)
0-8
8-12
12-17
17-23
23-31
31-41
Example:
Internal diameter or
edge length (mm)
100
110
120
130
140
150
Flexible ducting has been used for the
following example.
Exhaust connection, left . . . . . . . 4.9 m
Length (L) . . . . . . . . . . . . . . . . . . 1.2 m
Lower radius (R = 400 mm) . . . . 0.5 m
Height (H) . . . . . . . . . . . . . . . . . . 1.2 m
Upper radius (R) . . . . . . . . . . . . . 0.5 m
Wall pipe with louvred vent . . . . . 3.6 m
Effective duct length . . . . . . . . . 11.9 m
Result:
A duct diameter of 110 mm is adequate since the effective length is less
than 12 m as specified in Table II.
23
INSTALLATION INSTRUCTIONS
Moist air can be ducted outside by a wall
vent or window vent, both of which are
available from most hardware stores.
Window vent kit - example
Wall vent kit - example
1. Louvred wall vent frame
2. Wall vent duct
3. Adapter
4. Louvred wall vent
5. Flap
6. Screw
7. Wall anchor
1. Louvred window vent frame
4. Louvred window vent
5. Flap
8. Clips (4 pcs.)
9. Raised head screws (4 pcs.)
Dryer-side view:
1. Window vent kit
2. Adapter for vent duct
Dryer-top view:
1. Wall pipe
2. Flexible foam-gasket
A flexible foam gasket must be used if the
tumble dryer is directly connected to the wall
vent.
24
The window vent kit is installed into in a plexiglass pane. If using an existing glass pane, cut a
hole with a diameter of 125 mm.
INSTALLATION INSTRUCTIONS
Fig. 1
Ducting (side view) with flexible vent hose to an
exhaust flue.
1. Wall vent duct A. Wire spiral-wound hose
2. Adapter
B. Flexible ducting
3. Flue isulated against damp
Fig. 2
Ducting (side view) with plastic piping to a wall
vent kit.
Fig. 3
Connection of piping to the tumble dryer.
1. Drain pipe
2. Adapter for vent duct between tumble dryer
and plastic drain pipe
Fig.4
Height of vent outlet for washer dryer stack.
1. Wall vent kit
2. Adapter
3. Drain pipe (outer dia. 110 mm)
25
Technical data
Technical data
Height. . . . . . . . . . . . . . . . . . . . . . . . . .
85 cm (adjustable +1/-0.5 cm)
Width . . . . . . . . . . . . . . . . . . . . . . . . . .
59.5 cm
Depth (incl. distance from wall) . . . . . .
70 cm
Weight . . . . . . . . . . . . . . . . . . . . . . . . .
57 kg
Drum volume . . . . . . . . . . . . . . . . . . . .
126 l
Capacity . . . . . . . . . . . . . . . . . . . . . . . .
6 kg dry laundry
Rated load . . . . . . . . . . . . . . . . . . . . . .
See Data Plate
Fuse rating . . . . . . . . . . . . . . . . . . . . . .
See Data Plate
26
Consumption data
Consumption data
load
Final spin speed in washer*
Electrical
consumption
kg
rpm
kwh
Drying time
incl.
cooling down
time
mins
Extra dry
6
1200
1400
1600
3.65
3.50
3.20
92
89
81
Normal
6
1200
1400
1600
3.15
3.00
2.70
82
79
71
Normal-
6
800 (70 % residual moisture)
1200
1400
1600
3.85
3.00
2.85
2.55
98
79
75
68
Hand iron rr
6
800 (70 % residual moisture)
1200
1400
1600
3.10
2.25
2.10
1.80
82
63
59
52
Machine iron
6
1200
1400
1600
1.80
1.65
1.35
52
48
41
Cottons
Permanent Press
Normal +
3
1000
1.49
44
Normal
3
1000 (50 % residual moisture)
1.40
41
Hand iron
3
1000
1.20
37
The specified program running times and electrical consumption values were established under standard conditions (EN 61121/A11).
Different types of fabrics, load size and residual moisture after spinning may effect the specified
values.
*These values apply if the laundry is spun in a Miele washing machine before drying.
27
All rights reserved/001
3498
This paper is made from 100% chlorine-free bleached cellulose and therefore protects the environment.
Download PDF