Miele DA 289 Operating instructions

Operating and installation instructions
Ventilation System
DA 289-3
To prevent accidents
and machine damage,
read these instructions
before installation or use.
UV
M.-Nr. 05 853 730
Table of contents
IMPORTANT SAFETY INSTRUCTIONS
Functional description
Guide to the hood
Operation
Main power switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Turning on the fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Selecting the power level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Delayed Shut Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Turning off the fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Turning the lighting on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Dimming the lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Grease filter timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Checking the grease filter timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Reprogramming the grease filter timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Cleaning and care
Grease filter and air intake panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Cleaning the casing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Changing the light bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
After Sales Service
Installation instructions
2
IMPORTANT SAFETY INSTRUCTIONS
Read these Operating Instructions carefully before installing or
using the Ventilation System.
This appliance is intended for
residential use only. Use the
appliance only for its intended
purpose. The manufacturer cannot
be held responsible for damages
caused by improper use of the
hood.
This appliance complies with current
safety requirements. Improper use of
the appliance can lead to personal
injury and material damage.
READ AND SAVE THESE
INSTRUCTIONS
CAUTION
For General Ventilating Use Only.
Do Not Use To Exhaust Hazardous
Or Explosive Materials And Vapors.
This appliance is designed to vent
cooking smoke and odors only.
Be certain your appliance is properly installed and grounded by a
qualified technician.
To guarantee the electrical safety of this
appliance, continuity must exist
between the appliance and an effective
grounding system. It is imperative that
this basic safety requirement be met. If
there is any doubt, have the electrical
system of the house checked by a
qualified electrician. The manufacturer
can not be held responsible for
damages caused by the lack, or
inadequacy of, an effective grounding
system.
Before connecting the appliance to
the power supply make sure that
the voltage and frequency listed on the
data plate correspond with the household electrical supply. This data must
correspond to prevent machine
damage. Consult a qualified electrician
if in doubt.
Installation work and repairs should
only be performed by a qualified
technician in accordance with all
applicable codes and standards.
Repairs and other work by unqualified
persons could be dangerous and the
manufacturer will not be held
responsible.
3
IMPORTANT SAFETY INSTRUCTIONS
This equipment is not designed for
maritime use or for use in mobile
installations such as caravans or aircraft. However, under certain conditions
it may be possible for an installation in
these applications. Please contact the
nearest Miele dealer or the Miele Technical Service Department with specific
requirements.
Before servicing or cleaning the
unit, switch power off at the service
panel and lock the service disconnecting means to prevent power from being
switched on accidentally. When the
service disconnecting means can not
be locked, securely fasten a prominent
warning device, such as a tag, to the
service panel.
Before discarding an old
appliance, unplug it from the
power supply and remove the power
cord and any doors to prevent hazards.
Use
Do not allow children to play with
or operate the appliance or its
controls. Supervise its use by the
elderly or infirm.
Be careful when preparing a
flambé beneath the hood.
Flames may be drawn up into the hood
by the suction or grease filters may
catch fire.
Never operate gas burners without
pots.
Do not leave cooking surfaces
unattended while in use. Overheated food, oil and grease can catch
fire.
Do not use the hood without the
grease filters in place.
Clean the grease filters regularly.
Dirty filters are a fire hazard.
Do not use a steam cleaner to
clean the hood. Steam could
penetrate electrical components and
cause a short circuit.
In areas subject to infestation by
cockroaches or other pest, keep
the appliance and its surroundings
clean at all times. Any damage caused
by cockroaches or other pest will not
be covered under warranty.
4
IMPORTANT SAFETY INSTRUCTIONS
, WARNING - TO REDUCE
THE RISK OF A RANGE TOP
GREASE FIRE:
Never leave surface units unattended at high settings. Boilovers
cause smoking and greasy spillovers
may ignite. Heat oils slowly on low or
medium settings.
Always turn hood "ON" when cooking at high heat or when cooking
flaming foods.
Clean ventilating fans frequently.
Grease should not be allowed to
accumulate on fan or filter.
Use proper pan size. Always use
cookware appropriate for the size
of the surface element.
, WARNING
TO REDUCE THE RISK OF INJURY
TO PERSONS IN THE EVENT OF A
RANGE TOP GREASE FIRE,
OBSERVE THE FOLLOWING:
SMOTHER FLAMES with a close
fitting lid, cookie sheet, or metal
tray, then turn off the burner.
BE CAREFUL TO PREVENT BURNS.
If the flames do not go out immediately,
EVACUATE AND CALL THE FIRE
DEPARTMENT.
NEVER PICK UP A FLAMING
PAN - You may be burned.
DO NOT USE WATER, including
wet dishcloths or towels - a violent
steam explosion will result.
Use an extinguisher
ONLY IF:
– You know you have a Class ABC
extinguisher, and you already know
how to operate it.
– The fire is small and contained in the
area where it started.
– The fire department is being called.
– You can fight the fire with your back
to an exit.
5
IMPORTANT SAFETY INSTRUCTIONS
Installation
, WARNING
To reduce the risk of fire, use
only metal ductwork.
When installing the hood, make
sure that a minimum safety distances of 14 3/8" is maintained between
a Miele cooktop and the bottom of the
hood.
If local building codes require a greater
safety distance, follow their requirement.
For non-Miele cooking appliances
maintain the safety distances recommended by the cooktop manufacturer
in their installation and operating
instructions.
If there is more than one appliance
beneath the hood and they have different minimum safety distances always
select the greater distance.
Be careful not to damage hidden
electrical wiring or plumbing when
cutting or drilling into the wall or ceiling.
Do not use an extension cord to
connect the appliance to electricity.
Extension cords do not guarantee the
required safety of the appliance, (e.g.
danger of overheating).
Do not install this hood over
cooktops burning solid fuel.
Any fittings, sealant, or materials
used to install the ductwork must
be made of approved non-flammable
materials.
6
Never connect an exhaust hood to
an active chimney, dryer vent, vent
flue, or room ventilating ductwork. Seek
professional advice before connecting
an exhaust hood vent to an existing,
inactive chimney or vent flue.
Ducted fans must always be
vented outdoors.
Make sure that the airflow in the
room is sufficient for combustion
and exhausting of all non-electric heating appliances (water heaters, gas
cooktops, gas ovens, etc.), otherwise
backdrafts may occur. Follow the heating manufacturer’s guidelines and
safety standards or those published by
the National Fire Protection Association
(NFPA), or the American Society for
Heating, Refrigeration and Air
Conditioning Engineers (ASHRAE).
If in doubt, consult an experienced
professional.
Functional description
The ventilation hood works by air extraction. The air is drawn in through the
air intake panel, cleaned by the grease
filter and directed outside.
The hood comes equipped with a
non-return flap. This flap automatically
closes when the hood is turned off so
that no exchange of outside air and
room air can occur. When the hood is
turned on, the air pressure of the exhaust fan automatically opens the flap
blowing the inside air and cooking
odors outside.
7
Guide to the hood
8
Guide to the hood
a Chimney extension
i Light button
b Chimney
This button turns the light on and off
and also dims the light.
c Canopy
The lighting can be used independently
of the fan.
d Control panel
e Overhead lighting
j On/Off button
k Fan power selection
f Main power switch
Four fan speed selection
g Grease filter
l
h Air intake panel
Delayed shut down
This button activates the Delayed Shut
Down feature. The fan can be set to
turn off automatically after either 5 or 15
minutes.
m Grease filter button
The indicator above the grease filter
button lights when the grease filter and
air intake panel need to be cleaned.
This button is also used:
– to reset the grease filter timer after
cleaning the grease filter and air
intake panel (see "Cleaning and
Care").
– to show how long the grease filter
has been in use (see "Operation /
Filter timers").
– to change the number of hours
counted by the grease filter timer
(see "Operation / Reprogramming the
filter timers").
9
Operation
Main power switch
Selecting the power level
^ Remove the air intake panel to access the main power switch (see
"Cleaning and Care").
^ Use the _ controls to select the
desired power level.
^ Press the main power switch to "I".
The fan and lighting are ready to use.
If the appliance is not going to be used
for a long period of time (e.g. while vacationing) it should be turned off at the
main power switch to "0".
The next time it is turned on, the hood
will operate at the level previously used.
& =increases the fan speed
$ =decreases the fan speed
Level "1" to "3" (green indicators) are
usually sufficient for normal cooking.
Intensive setting
Level "4" (yellow indicator) should be
used for a short period when frying or
cooking food with a strong aroma.
Turning on the fan
Fan performance
^ Press the On/Off button.
The maximum air flow capacity is
625 cfm. Factors such as narrow duct
diameter and bends will affect this
value.
Level 1 operates at 40% capacity
Level 2 operates at 60% capacity
Level 3 operates at 80% capacity
Level 4 operates at 100% capacity
10
Operation
Delayed Shut Down
Turning the lighting on/off
If odors or smoke remain in the kitchen
after cooking has been completed, the
Delayed Shut Down feature can be selected to allow the hood to continue
running for either 5 or 15 minutes.
The overhead lighting can be turned
on and off independently of the fan.
^ Press the light button briefly to turn
on the lighting.
^ Press the Delayed Shut Down button
while the fan is still running.
Press once = 5 minute delay
(left indicator lights)
Press twice = 15 minute delay
(right indicator lights)
To cancel the Delayed Shut Down feature press the button again.
Turning off the fan
^ Press the On/Off button to turn the
fan off.
The indicator goes out.
Automatic Safety Shut Off
The fan will turn off automatically 10
hours after the last button was activated.
The lighting however will remain on.
The light button indicator illuminates.
^ Press the light button briefly again to
turn off the lighting.
The light button indicator will go out.
Dimming the lighting
The brightness of the lighting can be
adjusted.
^ While the lighting is turned on, press
the light button.
The lighting will dim until the button is
released.
^ If the button is pressed again, the
lighting will brighten until the button is
released.
If the button is pressed continuously,
the light will cycle between bright and
dark.
^ Press the light button again to turn off
the lighting.
^ Press the On/Off button to turn the
fan back on again.
11
Operation
Grease filter timer
Checking the grease filter timer
A timer monitors the hours of fan operation. The indicator for the grease filter
will light after 30 hours of operation. The
grease filter and air intake panel must
then be cleaned.
To check the percentage of time already used:
After the grease filter has been cleaned
and put in place, the grease filter timer
must be reset.
^ To do this, press the grease filter button for about 3 seconds.
^ Press the On/Off button to turn the
fan on.
^ Press the grease filter button.
The indicator will go out.
The number of flashing _ indicators
show the percentage of programmed
hours that have been used.
1 indicator = less than 25 %
2 indicators = less than 50 %
3 indicators = less than 75 %
4 indicators = less than 100 %
This information will remain stored in
memory in the event of a power failure.
12
Operation
Reprogramming the grease filter
timer
The grease filter timer is preset to 30
hours. This time can be lengthened or
shortened to 20, 30, 40 or 50 hours.
^ Press the On/Off button to turn off the
fan.
– A time of 20 hours should be programmed in kitchens with frequent
pan or deep frying.
– A time of 20 hours should also be
programmed if the kitchen is only
used occasionally to prevent grease
which has accumulated over a long
period of time from hardening on the
filters making cleaning more difficult.
^ Press the Delayed Shut Down and
grease filter buttons at the same time.
The indicator for the grease filter and
one of the _ indicators will flash.
The lit _ indicator shows the programmed time:
1st indicator from the left
2nd indicator from the left
3rd indicator from the left
4th indicator from the left
=
=
=
=
20 hours
30 hours
40 hours
50 hours.
^ Use the $ or & button to select the
desired time.
^ Store the selection by pressing the
grease filter button.
If the procedure is not stored within
4 minutes of programming, the hood
will automatically default to the "old"
data.
13
Cleaning and care
Grease filter and air intake
panel
Removing the air intake panel
The reusable metal grease filter removes solid particles from the vented
kitchen air (grease, dust, etc).
The grease filter and the air intake
panel should be cleaned every 3 - 4
weeks or whenever the grease filter indicator lights.
Keep the grease filter clean to prevent a fire hazard.
^ To remove the air intake panel gently
pull out and downward, shifting the
lower part a bit to the right. Lift it out
of the latches.
Removing the grease filter
To remove the grease filter, pull on the
lever.
14
Cleaning and care
^ Clean the filter
- by hand: use a scrub brush in
warm water with a mild detergent.
- in a dishwasher: place the filters in
the lower basket, making sure that
the spray arm is not blocked.
Depending on the detergent, cleaning the grease filter in a dishwasher
may cause permanent discoloration
of the filter surface. Performance of
the filter will not be affected by this
discoloration.
^ After cleaning, the filter can be
placed on a towel to air dry.
^ Clean the air intake panel according
to "Cleaning the casing".
^ While the filter and the air intake
panel are removed, clean any dirt or
grease from the interior casing to prevent the risk of fire.
^ Push the grease filter back in place.
^ Hook the air intake panel on the
latches and push a little to the left.
Push it toward the unit so that it clicks
in place.
^ After returning the grease filter, press
the grease filter button for 3 seconds
to reset the timer.
The indicator light will go out.
^ If the grease filter and air intake
panel are cleaned before the grease
filter timer has reached its maximum,
the grease filter button should be
pressed for 6 seconds to reset the
counter to zero.
15
Cleaning and care
Before cleaning or servicing the
hood, disconnect it from the power
supply by either removing the fuse,
unplugging it from the outlet or manually "tripping" the circuit breaker.
Cleaning the casing
,Never use abrasive cleaners,
scouring pads, steel wool or caustic
(oven) cleaners on the hood. They
will damage the surface.
^ The air intake panel, exterior surfaces
and controls can be cleaned with
warm water and liquid dish soap applied with a soft sponge.
^ Wipe dry using a soft cloth.
Only use a slightly damp sponge
when cleaning the controls. Water
could penetrate into the electronics
and cause damage.
Glass surfaces can be cleaned using
glass cleaner.
16
Stainless steel
Stainless steel surfaces can be cleaned
using a non-abrasive stainless steel
cleaner.
To help prevent resoiling, a conditioner
for stainless steel can also be used.
Apply sparingly with even pressure.
Stainless steel colored controls
^ These controls may become discolored or damaged if not cleaned regularly.
Do not use a stainless steel cleaner
on these controls.
Cleaning and care
Changing the light bulbs
Before changing the light bulbs, disconnect the hood from the power
supply by either removing the fuse,
unplugging it, or manually "tripping"
the circuit breaker.
When in use halogen bulbs become
extremely hot, and they can burn
your hands. Do not attempt to
change the bulbs until they have
had sufficient time to cool down.
Do not touch the bulb surface. Fingerprints or body oils deposited on
the bulb will decrease the life of the
bulb. Please follow the bulb manufacturer’s instructions.
^ Pull the old bulb out of its socket using the enclosed lever. Replace it
with a new one. Be careful not to
drop the bulb on the cooktop.
Replacement bulbs may be ordered
from Miele’s Technical Service Department.
USA 1-800-999-1360
CDN 1-800-565-6435
17
After Sales Service
In the event of a fault which you cannot
correct yourself please contact:
– Your Miele Dealer
or
– The Miele Technical Service
Department
USA
1-800-999-1360
techserv@mieleusa.com
CDN
1-800-565-6435
service@miele.ca
When contacting the Technical Service
Department, please quote the model
and serial number of your appliance.
These are shown on the data plate
which is visible when the grease filter is
removed.
18
Installation instructions
Table of contents
Caring for the environment
Installation accessories
Plywood backing
Electrical data
Appliance dimensions
Installation
Installation instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Dismantling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Air extraction
Condensate trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
20
Caring for the environment
Disposal of packing material
Disposal of an old appliance
The cardboard box and packing
materials protect the appliance during
shipping. They have been designed to
be biodegradable and recyclable.
Please recycle.
Old appliances may contain materials
that can be recycled. Please contact
your local recycling authority about the
possibility of recycling these materials.
Ensure that any plastic wrappings,
bags etc. are disposed of safely and
kept out of the reach of children.
Danger of suffocation!
Before discarding an old hood, unplug it from the outlet and cut off its
power cord to prevent hazards.
21
Installation accessories
22
Installation accessories
a 3 protective shields
prevent scratches to the chimney during installation.
b Upper retaining plate secures the
chimney extension.
c Middle retaining plate for additional stability of the chimney.
5 large headed screws 5 x 40 mm
for securing the retaining plates and the
canopy.
(S8 wall anchors included in the packaging are not for use in USA / CDN.)
d 2 hose clips for securing the
ducting.
e 1 reducing collar
for use with 5" (125 mm) exhaust
ducting.
f 1 non-return flap for vented air
extraction only.
Caution: During the installation process, please be careful of sharp
edges that can cause harm.
2 screws 5 x 60 mm for securing the
chimney.
6 screws 3.5 x 9.5 mm for securing the
canopy and filter housing
1 lever for dismantling the chimney and
changing the light bulbs
Installation instruction sheet
23
Plywood backing
The majority of the weight of the installed ventilation system will be
supported by the lower retaining
plate. It must be firmly attached to
the stud framing behind the drywall.
If studs are not available in the required locations, a plywood backing
(min. 1/2" (13 mm) thick) spanning at
least two studs must be installed.
Failure to adequately support the
weight as stated may result in the
ventilation system falling off the wall,
causing personal injury and property
damage.
(If plywood backing is not needed, proceed to the included installation sheet.)
To install a plywood backing
^ Find the studs to the left and right of
the mounting location by tapping the
wall or using a stud finder.
^ Mark a vertical cutting line along the
center of each stud.
Be careful not to damage any wiring
or plumbing that may be located behind the wall. Make sure that the
power supply to the area where this
installation is being performed has
been turned off at the breaker panel
before cutting into the wall.
^ Remove the drywall between the cutting lines and replace it with plywood
of a matching thickness (min. 1/2"
(13 mm) thick). Tape the joints and
refinish the wall.
^ Proceed to the included installation
sheet to complete the installation.
^ Determine and mark the location of
the retaining plate for the canopy as
outlined on the installation sheet.
^ Make a cutting line 3" (76 mm) above
and 3" (76 mm) below the outline of
the retaining plate.
24
Electrical data
All electrical work should be performed by a qualified electrician in
strict accordance with national and
local safety regulations.
Installation, repairs and other work
by unqualified persons could be
dangerous. The manufacturer can
not be held responsible for unauthorized work.
Ensure that power to the appliance
is OFF while installation or repair
work is performed.
Important
The hood comes equippped with a 5 ft
(1.5 m) power cord with a NEMA 5-15
molded plug for connection to a
120 VAC, 60 Hz, 15 A power outlet.
Maximum load . . . . . . . . . . . . . . 390W
Light. . . . . . . . . . . . . . . . . . . . . 4 x 10 W
Voltage . . . . . . . . . . . . . . . . . . . . . 120 V
Frequency . . . . . . . . . . . . . . . . . . 60 Hz
Circuit rating. . . . . . . . . . . . . . . . . . 15 A
Verify that the voltage, load and circuit
rating information found on the data
plate (located behind the grease filter),
match the household electrical supply
before installing the hood.
If there is any question concerning the
electrical connection of this appliance
to your power supply, please consult a
licensed electrician or call Miele’s Technical Service Department.
USA 1-800-999-1360
CDN 1-800-565-6435
WARNING:
THIS APPLIANCE MUST BE
GROUNDED
25
Appliance dimensions
26
Appliance dimensions
Cut out area in wall or ceiling for
entrance of 6" (150 mm)
ductwork or 5" (125 mm)
ductwork with a reducing collar.
Standard unit height H =
37 13/16" - 51 15/16"
(960 – 1320 mm)
Read the entire installation procedure
and determine height (S) before beginning the installation. Installations differ
depending on the model and venting
method. If the hood is fitted flush to the
ceiling, the sum of S + H + Workspace
should not exceed the room height.
Distance S above the cooktop
Do not install this exhaust hood over
cooktops burning solid fuel.
When installing the hood, make sure
that the minimum safety distance
(S) between the top of a Miele
cooktop and the bottom of the hood
3
is at least 14 /8" (365 mm).
For non-Miele cooking appliances
maintain the safety distances recommended by the cooktop manufacturer in their installation and operating instructions.
If there is more than one appliance
beneath the hood and they have different minimum safety distances always select the greater distance.
See "IMPORTANT SAFETY INSTRUCTIONS" for further information.
27
Installation
Installation instruction
Dismantling
See the enclosed installation instruction
sheet.
If the hood needs to be disassembled,
follow the instructions on the installation
sheet in reverse order.
Please read the "Important Safety Instructions" and Installation instructions
before installing this hood.
A lever is enclosed for easier removal
of the chimney extension.
Protective film
The casing is covered by a protective
film to prevent scratches during transport.
Peel off the film before installing the
casing parts.
^ After removing the screws from the
chimney, slide the lever between
chimney and chimney extension and
gently apply pressure to ease the
chimney from its hooks.
28
Air extraction
,WARNING
Danger of toxic fumes.
Gas cooking appliances release
carbon monoxide that can be
harmful or fatal if inhaled.
The exhaust gases extracted by
the hood should be vented outside of the building only.
Do not terminate the exhaust
ducts in attics, garages,
crawlspaces, etc.
To reduce the risk of fire, only use
metal ductwork.
Please read and follow the
"IMPORTANT SAFETY
INSTRUCTIONS" to reduce the risk of
personal injury. Follow all local building
codes when installing the hood.
Exhaust ducting and connections
– The ducting should be as short and
straight as possible, and the number
of sharp bends should be minimized.
– For most efficient air extraction, the
diameter of the ductwork should not
be less than 6" (150 mm). Use of flat
ducts also reduces the air extraction
efficiency.
– Noise levels of the hood will increase
if flat ducts or round ducts of less
than 6" (150 mm) in diameter are
used.
– Use smooth or flexible pipes made
from approved non-flammable materials for exhaust ducting.
– Where the ductwork is horizontal, it
must slope away from the hood at
least 1/8" per foot (1cm per meter) to
prevent condensation dripping into
the appliance.
– If the exhaust is ducted through an
outside wall, a Miele Telescopic Wall
Vent can be used.
29
Air extraction
Condensate trap
Important:
If the ductwork runs through rooms,
ceilings, garages, etc. where temperature variations exist, it may need to be
insulated to reduce condensation. In
some cases, a condensate trap may
also be required to collect and evaporate any condensate which may occur.
When installing a condensate trap,
ensure that it is positioned vertically
and if possible directly above the
exhaust outlet.
– If the exhaust is ducted into an inactive flue, the air must be expelled
parallel to the flow direction of the
flue.
Never connect an exhaust hood to
an active chimney, dryer vent, vent
flue, or room venting ductwork. Seek
professional advice before connecting an exhaust hood vent to an existing, inactive chimney or vent flue.
30
31
Alteration rights reserved /5002
This bio-friendly paper was bleached without the use of chlorine.
M.-Nr. 05 853 730 / V00