AMX | NXA-ENET8-2POE | Specifications | AMX NXA-ENET8-2POE Specifications

Quick Start Guide
MSD-431-L 4.3” Modero S Series® Wall Mount Touch Panel
Overview
Series®
The Modero S
is a touch panel family sophisticated enough for room
control yet priced right for the most cost sensitive installations, including small
huddle spaces and dedicated room scheduling. The smallest of our Modero S
Series wall mount touch panels, the MSD-431-L 4.3” Wall/Flush Mount Touch
Panel (FG2265-03) still features the advanced technology empowering users to
conduct seamless meetings including VoIP, brilliant 24-bit color depth, PoE
connectivity, and streaming video.
Microphone
Sleep Button
Right LED
Left LED
RJ-45
Port
(Front)
Note: For more information on installation and configuration, as well as
complete specifications on this device, please refer to the MSD-431-L/MST-431
Operation/Reference Guide, available at www.amx.com.
Panel Connectors and Wiring
FIG. 1 shows the connectors located on the back of the MSD-431-L.
Power for the MSD-431-L via Power Over Ethernet
Power for the MSD-431-L is supplied via Power Over Ethernet (PoE), utilizing an
AMX-certified PoE injector such as the PS-POE-AF-TC PoE Injector
(FG423-83) or other approved AMX PoE power source. The incoming Ethernet
cable should be connected to the RJ-45 port on the MSD-431-L.
Note: The Micro A/B USB port is used only for firmware uploads, as it is
inaccessible when the device is installed within its back box.
Installing the MSD-431-L
The MSD-431-L can be installed either directly into a solid surface environment,
using either solid surface screws or the included locking tabs for different
mounting options. For more information, please refer to the MSD-431-L/MST431 Operation/Reference Guide, available at www.amx.com.
The MSD-431-L is contained within a clear outer housing known as the back
box. This back box is removed when installing the device into a wall or into a
Rough-In Box.
Installing the MSD-431-L into a wall
The back box (FIG. 2) is designed to attach the panel to most standard wall and
solid surface materials. This back box has two locking tabs (one on the top and
one at the bottom) to help lock the back box to the wall. These locking tabs are
only extended AFTER the back box is inserted into the wall. Using the locking
tabs is highly recommended for standard mounting surfaces such as walls. For
thin walls and solid surfaces, use #4 mounting screws (not included).
RJ-45
Port
Knockout
Micro A/B
USB Port
(Rear)
Locking
Tab
FIG. 1 MSD-431-L
Product Specifications
MSD-431-L Specifications
Power:
PoE (Power over Ethernet), 802.3af, class 2
Power Consumption:
•
•
•
•
•
Maximum: 5W
Typical: 3W
Standby: 2W
Shutdown: 0.6W
Startup Inrush Current: Not Applicable due to PoE
standard
•
•
•
•
•
Operating Temperature: 32° F to 104° F (0° C to 40° C)
Storage Temperature: 4° F to 140° F (-20° C to 60° C)
Humidity Operating: 20% to 85% RH
Humidity Storage: 5% to 85% RH
Power (“Heat”) Dissipation: 13.6 BTU/hr,
Standby: 6.8 BTU/hr
Operating Environment:
Dimensions (HWD):
With Back Box: 3.42” x 5.05” x 2.30”
(87 mm x 128 mm x 58 mm)
Weight:
• Without Back Box: 0.50 lbs (0.22 Kg)
• With Back Box: 0.65 lbs (0.29 Kg)
Certifications:
•
•
•
•
•
•
•
•
Included Accessories:
• MSD-431-L Wall Mounting Template (68-2265-01)
UL
FCC Part 15 Class B
C-Tick CISPR 22 Class B
CE EN 55022 Class B and EN 55024
CE EN 60950-1
IC CISPR 22 Class B
VCCI CISPR 22 Class B
RoHS/WEEE compliant
Note: Optimal performance requires use of one of the following AMX PoE power
supplies (not included):
• PS-POE-AF-TC, PoE Injector, 802.3AF Compliant (FG423-83)
• NXA-ENET8-2POE, Gigabit PoE Ethernet Switch (FG2178-63)
Note: AMX does not support the use of non-AMX power supplies.
MSD-431-L
Back
Box
Knockout
FIG. 2 MSD-431-L Back Box (Side View)
WARNING: When installing the back box, make sure that the assembly is in the
correct position and in the correct place. Once the locking tabs are extended
and locked into place, removing the back box may be difficult without having
access to the back of the wall or causing damage to the wall.
Note: In order to guarantee a stable installation of the MSD-431-L, the thickness
of the wall material must be a minimum of .50 inches (1.27cm) and a maximum
of .875 inches (2.22cm). The surface should also be smooth and flat.
WARNING: The maximum recommended torque to screw in the locking tabs on
the plastic back box is 5 IN-LB [56 N-CM]. Applying excessive torque while
tightening the tab screws, such as with powered screwdrivers, can strip out the
locking tabs or damage the plastic back box.
1.
After ensuring proper placement, cut out the mounting surface. Use the
included mounting template (68-2265-01) or refer to the dimensions in the
MSD-431-L/MST-431 Operation/Reference Guide, available from
www.amx.com, for more information.
CAUTION: Making sure the actual cutout opening is slightly smaller than the
provided dimensions is highly recommended. This action provides the installer
with a margin for error if the opening needs to be expanded. Too little wall
material removed is always better than too much.
2.
Remove either the top or the bottom knockout from the back box,
depending upon the required installation. Thread the incoming wiring
through the hole in the rear of the back box.
3.
Thread the incoming Ethernet wiring from their terminal locations through
the surface opening and through the access slot.
4.
Push the back box flat into the mounting surface and secure with either the
locking tabs or #4 mounting screws (not included). In order to prevent
damage to the touch panel, make sure that any screws used are flush with
the back box, and the back box goes freely into the opening.
5.
Insert each connector into its corresponding location along the back of the
MSD-431-L.
6.
Test the incoming wiring by attaching the panel connections to their
terminal locations and applying power. Verify that the panel is receiving
power and functioning properly to prevent repetition of the installation.
Note: Do not disconnect the connectors from the touch panel. The unit must be
installed with the attached connectors before being inserted into the drywall.
7.
Latch the panel onto the top hooks on the back box and rotate it down.
Press gently but firmly and evenly on the surface of the glass until the top
panel snap “clicks” to lock it down.
WARNING: if you see a gap between the panel and the back box, or feel any
binding while locking down the panel, stop immediately and verify that no cables
or other items are in the way. Do not force the panel into position, as this can
cause damage to the touch screen or the panel electronics.
8.
5.
6.
Press the Device Name field to open the Device Name keypad.
Enter a unique Device Name assignment for the panel and press OK.
Accessing the Connection & Networks Page
1.
2.
From the Settings Page, select Connection & Networks. If the page is
password protected, this opens a password keypad.
Enter the panel password into the keypad (the default is 1988) and select
OK to access the page.
Connecting to a Master
The panel requires that you establish the type of connection you want to make
between it and your Master.
In the Connection & Networks page:
1.
Select Master Connection to open the Master Connection page (FIG. 4).
Reconnect the terminal Ethernet and USB to their respective locations on
either the Ethernet port or NetLinx Master.
Uninstalling the MSD-431-L
In order to access the back of the MSD-431-L, such as to install a USB
connection for firmware upgrades, the device may need to be uninstalled from
the back box. To uninstall the MSD-431-L:
9.
From the bottom, pull gently outward from the back box. Gently rock the
panel back and forth to free the bottom from the back box.
10.
Rotate it up to release the top latch hooks, and carefully pull the device
free from the back box. Take care not to damage or pull the connections on
the back of the device.
Configuring the MSD-431-L
The MSD-431-L is equipped with Settings Pages that allow you to set and
configure various features on the panel. For more information on connecting and
configuring the MSD-431-L to a network, please refer to the Modero S Series
Programming Guide, available at www.amx.com.
Accessing the Settings Pages
FIG. 4 Master Connection page
2.
Press Mode to toggle through the available connection modes:
Connection Modes
Mode Description
Procedures
Auto
The device connects to the first
master that responds.
This setting requires that you set
the System Number.
Setting the System Number:
1. Select Master System Number to open
the keypad.
2. Set your Master System Number and
select OK.
URL
The device connects to the
specific IP of a master via a TCP
connection.
This setting requires that you set
the Master’s IP.
Setting the Master IP:
1. Select the Master IP number to the
keyboard.
2. Set your Master IP and select OK.
Listen
The device “listens” for the
Master to initiate contact.
This setting requires you provide
the master with the device’s IP.
Confirm device IP is on the Master URL list.
You can set the Host Name on the device
and use it to locate the device on the master.
Host Name is particularly useful in the DHCP
scenario where the IP address can change.
To access the Settings Pages on the MSD-431-L, press and hold the Sleep
Button (FIG. 1) on the top of the panel for 3 seconds. The user will be prompted
to release the button to enter the Settings page (FIG. 3).
3.
FIG. 3 Settings page
Accessing the Configuration Page
1.
2.
From the Settings Page, select Configuration. If the Configuration page is
password protected, this opens a password keypad.
Enter the panel password into the keypad (the default is 1988) and select
OK to access the page.
Setting the Panel’s Device Number and Device Name
In the Configuration page:
1.
Press Panel to open the Panel Configuration page.
2.
Ensure that the Synchronize Device Names button is not selected, and
click it to deselect it if it is.
3.
Press Device Number to open the Device Number keypad.
4.
Enter a unique Device Number assignment for the panel and press OK.
If you have enabled password security on your Master, you need to set the
username and password within the device.
a. Select Username to open the Master User keyboard.
b. Set your Username and select OK.
c. Select the Password to open the Master Password keyboard.
d. Set your Master Password and select OK.
e. Press the Back button twice to return to the Settings page.
Configuring the Panel to a Network
The first step is to configure the panel’s communication parameters. This only
configures the panel to communicate with a network, and it is still necessary to
tell the panel with which Master it should be communicating.
Network Communication With a DHCP Address
In the Connection & Networks page:
1.
Select Network Connection to open the Network Connection page.
2.
Toggle the DHCP/Static field until the choice cycles to DHCP. This action
causes all fields on the page (other than Host Name) to be greyed-out.
3.
Select Host Name to open the Host Name keyboard. Enter the new host
name and click OK.
For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).
8/13
©2013 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
AMX reserves the right to alter specifications without notice at any time.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com
93-2265-03
REV: D
Download PDF