ST-66552 AIR TIRE BUFFER (4000RPM)
PARTS LIST
No. Parts No.
1
66552-01
2
66552-02
3
66552-03
4
66552-04
5
66552-05
6
66552-06
7
66552-07
8
66552-08
9
66552-09
10
66552-10
11
66552-11
12
66552-12
13
66552-13
14
66552-14
15
66552-15
16
66552-16
66552 16
17
66552-17
18
66552-18
Description
Motor Housing
Valve Bushing
Lever Pin
Valve Stem
O-Ring
O-Ring
Spring
Regulator
O-Ring
O-Ring
Valve Screw
Throttle Lever
Stop Rod
Spring
Pin
Silencer
Sil
Deflector
Air Inlet
Q'ty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
No.
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
Parts No.
66552-19
66552-20
66552-21
66552-22
66552-23
66552-24
66552-25
66552-26
66552-27
66552-28
66552-29
66552-30
66552-31
66552-32
66552-33
66552-34
66552 34
66552-35
66552-36
Description
Q'ty
Ball Bearing (626)
1
Rear End Plate
1
Pin
3
Cylinder
1
Rotor Blade
4
Washer
1
Annular Gear
1
Needle Bearing
3
Pin
3
Ball Bearing (6201)
2
Hexagon Nut
1
Nose Housing
1
Spanner Wrench (14mm)
1
Rotor
1
Front End Plate
1
Ball
B ll Bearing
B i (6000)
1
Pinion Gear
3
Gear Complete
1
ST-66552-P-0909A-GT
Foreword
Sumake is a manufacturer and exporter of air
tools since established. We have devote all our
efforts in improving quality and tools’ life. As
well as the noise and vibration of tools. Bring all
ki
ffi i
fit and
d enjoy
j
off you working
efficiences,
profits,
using the tool is our principle.
Features
This tool is designed to meet an extremely wide
range of metal materials to be cut into any shape,
t i ht side
id or curvedd side.
id
straight
A portion of the water content, however, is
condensed in the piping, and can enter the tool
mechanism, and may cause trouble. So, install an
air filter and on oiler between the compressor and
the tool. Use a 3 HP or larger compressor for
each sander.
2-3 Air hose
Clean the hose with a blast of compressed air
before connecting the hose to air tool. This will
prevent both moisture and dust within the hose
from entering the tool and causing possible rust
or malfunction. To compensate for unusually
long hose (over 25 ft), the line pressure should be
i
increased
d accordingly.
di l
Operator‘s instruction
1.
Main Applications
A breakthrough in cutting speed and durability.
This lightweight, fast cutting tool is ideally suited
for body shop and sheet metal work. Leaves sheet
metal smooth and free from burrs and distortion.
.
2.
Drainag
e
Cautions for Use
2-1 Air pressure
Maximum performance is displayed at the proper
sanding speed, obtainable at a gauge pressure of
6.2 bar. Range-wise, this is an air pressure from 5
to 7 bar (70 to 100 psi)
3. Operation, Adjusting And Replacing
M th d
Method
5
7
2 2 Air
2-2
Ai line
li
Use a 3/8“ air hose between the compressor and
the tool . Compressed air is cooled and its water
content separated, as soon as the air leaves the
compressor.
Coupler
Leader
hose
2-4 The approved eye protector, ear-muff,
mouth-muffle, and gloves should be worn when
operate this tool.
2-5 The working place shall be ventilative.
2-6 Release the on-off device in the case of
energy supply failure.
Recoil
hose
Water
separation
Air
supply
Regulator
Drain
daily
3.1 On-off device
To operate this tool, just push the lever toward
the tool itself. The tool continuously reciprocates
as one push the lever down and it stops running
as the lever is released.
Tool
Nipple
Oiler
For the sake of safety, put it on hanger or on a
soft flat pad when not in use.
3.2 Replace and adjusting
There is no user serviceable part inside this tool.
Please send the tool to a qualified personnel or our
service section to repair or/and replace worn parts.
4.
Maintenance
4-1 Lubrication
Before connecting the hose , apply 4 or 5 drops of
#60 spindle oil at the air inlet. Use of a thicker oil
can lead to reduced performance or malfunction.
If a thicker oil is used by accident, wipe it away
immediately Also
immediately.
Also, every 3 or 4 hours of
operation, oiling is necessary.
4-2 Storage
Avoid storing the tool in a location subject to high
humidity. If the tool is left as it is used , the
residual moisture inside the tool can cause rust.
Before
storing
oilil the
f
i and
d after
f operation,
i
h tooll at
the air inlet with spindle oil and run it for a short
time.
4-3 Disposal
If the tool is too seriously damaged to be used
anymore, drop it in a resource recycling can.
Never drop it into fire.
4-4 Ordering service Parts
For further operational and handling information
or for replacement of parts and components,
contact the sale agent from whom you purchased
the tool or the service division of our company.
* In ordering parts and components, give each
part number, name and quantity.
Warning
1. This tool is not insulted for coming into contact
with electric power source.
2. It is forbidden to use this tool in explosive
atmospheres and do not put any combustible
material near the workpiece since it emit sparks
when grind with metal material.
3. The metal cutting trash might be sharp and it is
blew out from the under part of Dies.
4 Prevent long hair or loose clothing from
4.
drawing in while operate this tool.
5. Never carry the tool by hose and beware of a
whipping compressed air hose.
6. The workpiece shall be fixed by proper device.
7. Keep your body balance and beware of the fall
of the severed workpiece
workpiece.
ST 66552 I 1807B GT
ST-66552-I-1807B-GT
">
