1 of 9
www.mikrotikchina.cn
www.mikrotikchina.com
Supported Hardware
This page should be edited by the user community to reflect their tested hardware and version used.
See also: Device driver list (http://www.mikrotik.com/testdocs/ros/2.9/guide/driverlist.php) in manual
Contents
1 Motherboards
2 Ethernet chipsets
3 x86 Systems
4 Embedded Controllers
5 3G cards
6 Memory cards
7 802.11a/b/g wireless cards
7.1 802.11n wireless cards
8 T1/E1
9 GPS
10 Storage controllers (SAS/SCSI/RAID)
Motherboards
Vendor
Model
ROS
version
Result
Asrock
Intel 82801G chipset
3.0-3.14
Bad performance, locks up under heavy load, supports multi cpu,
PATA not supported, integrated ethernet not recognized. Maybe it's
just Asrock bad motherboard don't know if the problem is in intel
82801G chipset tested on 2 motherboards, never tested on 2.9.x
ASUS
P5B-Deluxe (Intel P965,
3xPCI, 3xPCI-E)
3.13
Works fine on Intel Core 2 Duo E6400. Not supported PATA
controller. Both integrated Gigabit NIC (Marvell Yukon 88E8056 &
88E8001) works fine but only at 100Mbps.
ASUS
P5B-V (Intel P965, 3xPCI,
4xPCI-E)
3.13
Works fine on Intel Dual Core E2180. Not supported PATA
controller. Integrated Gigabit NIC Marvell Yukon 88E8001 works
fine but only at 100Mbps. Winbox via MAC = problem, disconnects
after 3 seconds. Winbox via IP no problem.
ASUS
P5KC (Intel P35, 3x PCI,
3xPCI-E)
3.10
Not supported PATA controller (JMicron JMB363), ROS can boot
from USB flash drive; internal ethernet not recognized.
ASUS
P5GC-MX/1333 (2x PCI)
3.7
Works great for pentium dual-core e2160, hdd pata and sata, 1,5gb
ram dual channel mode, except the attansic l2 ethernet onboard
card is not recognized.
ASUS
P5GC (6xPCI)
2.9.39
Ethernet recognized but not working
ASUS
P7P55D PRO
4.5
Works ok, PATA controller (JMicron JM363) and internal Ethernet
successfully recognized.
ASUS
P6T SE
4.0
RouterOS boots and works with SATA disk set to 'IDE compatibility
mode'.
ASUS
A7V133-C
3.0 beta 7
Works fine
ASUS
A7V600-X
3.25
Works fine
EPoX
EP-4VKMI
3.16 - 3.24
Works fine.
EPoX
8RDA+
3.6
Work fine including integrated ethernet
2.9.x
Excellent performance under 2.9. Not tested under v3. Onboard
Ethernet Works perfectly.
Intel
D815EGEW
Intel
DG950
2.9.42
Ethernet not recognized
Intel
D945GCCRL
2.9.43 &
3.0 beta 5
Ethernet & DoM not recognized
Intel
D945GCLF2
3.23
4 core's, 2gb ram, 32gb ssd, no problems.
Intel
D945GCPE
3.0 beta 9
Work fine including integrated ethernet
Works fine but integrated ethernet (just disable) goes up and down
on reboots multi-cpu= yes. shared IRQ for PCI devices, decrease
nic performace.
Intel
D945GCNL
3.11
Intel
D945GNT
2.9.45
Works fine
Intel
DP55WG
4.6
multi-cpu smp works great, onboard NIC not supported by
RouterOS 4.6 yet though, must use pci/pci express nics
Intel
DQ965GFEKR (D41676)
3.7, 3.4
Works fine on 3.7/3.4 if multi-cpu=no, BUT 3.5-3.7 fail to boot with
E4600 processor and multi-cpu=yes
www.edcwifi.com
source : Mikrotik Wikipedia
2 of 9
www.mikrotikchina.cn
www.mikrotikchina.com
Intel
D845GVSRL
3.7, 3.1,
2.9
Intel
DG965SWH
3.0 beta 9
Works fine, but only with SATA not IDE
Very Stable, used for 4 years
Intel
DG33FB
3.7
Works fine, Ethernet but not working (IRQ 9), set in BIOS
Security/XD Tegnology to disable
Intel
S3210SHLC
4.2
Boot from USB stick. Work fine for my PPPoE server. Up to 1300
users with summary 200Mbit traffic.
Intel
D945GZT-M
3.0rc4
Works fine
Chaintech
AADF950
3.0 beta 5
Works fine
Abit
KT7E
3.0 beta 7
Works fine
ECS
nForce3-A
3.6
Work fine including integrated ethernet
No Apparent Problems, Disabled any unneeded devices in the BIOS
ECS
P4M800PRO-M478
2.9.43
Abit
BE6
2.9.43
Works
VIA
EPIA-MII12000
2.9.42
Locks up under heavy load across wireless
Supermicro
5015M-MR
2.9.28
Motherboard is PDSMi w dual core
Supermicro
PDSBM-LN2+
2.9.51 &
3.16
http://forum.mikrotik.com/viewtopic.php?f=1&t=28184
Supermicro
PDSMi-LN4+
2.9.51,
3.13, 3.20
Very stable even with dual-cores enabled.
Gigabyte
GA-41M-ES2L
3.28
Works fine; CPU Intel Core2 Dual 2.7GHz; 2XRB44GV
Gigabyte
GA-6BXS
2.9.43
Works fine
Gigabyte
GA-8I848P-G
3.6
Work fine including integrated ethernet
Gigabyte
GA-8ST667 rev. 3.0
3.13
Works fine; CPU Intel Celeron 2,4GHz; Chipset SiS 645DX; 5xPCI;
Gigabyte
GA-M720-US3 rev 1.0
4.6
Works fine (downvolted to 1.1V)
Gigabyte
GA-MA790GP-UD4H
3.30
Works fine
Gigabyte
K8-NS-ULTRA
2.9.x-3.7
Excelent work, including both onboard ethernet (100 and 1000 lan)
Gigabyte
GA-MA770-DS3 (rev. 2.0)
3.10
Works fine and extreme stable include onboard LAN, IDE DOM can
load normally
Chipset P35 (Tested Using
Gigabyte GA-P35-DS3L &
Abit IP35)
3.7
Work fine but only with SATA, not IDE (Include DOM), bellow v3.7
problem with SATA too
Virtual PC 2007
3.7
Installs and and tries to boot.
Runs Wicked Fast! I have had up to 8 Ethernet interfaces running
simultaneously.
Microsoft
VMware
Workstation v6.0.3
3.7
VMware
ESXi v4
3.30
Select IDE type for virtual disk - works perfectly!
Xen 3.2.1 on Intel C2Q
4.x
Installs and runs fine on HVM bootloader using Intel VT technology.
Even switches to RouterOS console from Dom0 shell. Ethernet
interfaces work perfectly. Do not install xen/kvm RouterOS
packages!
DFI
AD73 Pro (Chipset VIA
KT266A/VT8233ACD)
2.9.x-3.30
Works fine. All 5 PCI's ocupied with 1 x LAN and 6 x R52H's (3 in
RouterBoard11 and 3 in RouterBoard14!)
DFI
AK75-EC (Chipset VIA
KT133A/686B)
3.14-3.30
Stable. All PCI's ocupied with LAN, miniPCI-PCI adapters fitted with
R5H/R52H's and XR5's
Fujitsu
Siemens
Primergy RX100S5
3.1, 3.7,
3.22
Can Install from Netinstall with RAID (LSI) Controller enable. Can't
install from CD and Netinstall with only SATA or PATA mode. But
NOT RUN
MSI
785GM-E51
4.11
Works fine, booted from USB stick, integrated LAN working
Ethernet chipsets
Vendor
ROS
version
Model
Result
Works! Extremely reliable, doesn't fully support
tagged vlans
3Com
3c905B Cyclone 100BaseTX
2.9.51
3Com
3cSOHO100-TX [Hurricane] (rev: 48)
3.14rc1
Works
3Com
3c905C-TX/TX-M [Tornado] (rev: 120)
2.9.51
Works! Extremely reliable, doesn't fully support
tagged vlans
3Com
3c905C-TX/TX-M [Tornado] (rev: 116)
2.9.51
Works! Extremely reliable, doesn't fully support
tagged vlans
3Com
3c905B-FX Fast Etherlink XL FX 100baseFx
[Cyclone] (rev: 0)
2.9.43
Works but no link in Winbox and no Graph in
Dude !!!!
Intel
S82557 10/100MBit
2.9.43
works
Intel
PWLA8391GT PRO1000/GT
3.7, 3.1, 2.9
Extremely Stable, used for years
Intel
PWLA8391GTL PRO1000/GT
3.4
Extremely Stable, used for years
Intel
82575EB & 8257GB
3.15
Added support
Intel
82576 Gigabit ET Quad port
4.5
Not recognized
www.edcwifi.com
source : Mikrotik Wikipedia
3 of 9
www.mikrotikchina.cn
www.mikrotikchina.com
Intel
82572EI (EXPI9300PTBLK)
4.5, 4.6
Works
Intel
82572GI (EXPI9400PTBLK)
4.5
Works
Intel
82574L (EXPI9301CT)
5.0 beta 1
Supported in ROS 5 / Works
Intel
82571EB (EXPI9404PT) QUAD
4.6
Works
Intel
S82557/S82555 10/100 Mbit TX
2.9.50 / 3.16
Works Stable! FCC ID:EJMNPDSPD035
Intel
PRO 1000 MT
2.9.51
Works
Intel
82541GI/PI Gigabit Ethernet Controller (rev: 5)
2.9.49
Working
Intel
10Gbit Ethernet PCI Express
3.17
Works
Intel
82557/8/9 Ethernet Pro 100 (rev: 5)/Dual
ports(Two ports/2-port)/RJ-45"
4.10
Works, fine!
D-Link
DFE-528TX rev. E1
3.13
Works
D-Link
DFE-580TX 4-port
3.0 beta 5
Bad card, not recommended. Hangs router
D-Link
DFE-530/538TX
2.9.43 - 3.x
Works well, no apparent problems.
D-Link
DUB-E100 USB
3.18
added support, reported to be working
Marvell
88E8001 Gigabit Ethernet Controller (rev: 20)
3.13
Works
3.6
reported to be working with some BIOS setting
enabled
Marvell
88E8056
DECchip
21143 (ZYNX ZX410 4-port cPCI)
2.9.51
Working
Realtek
RTL-8169 Gigabit Ethernet x4 (rev: 16)
3.0-3.11
Working Extremely reliable, used 4 mounts
Realtek
RTL8111 (10/100/1000Mbit)
3.10
Seems to be working only in older RouterOS v3
releases, v3.10 and before.
Realtek
RTL8111C, RTL8111DL (10/100/1000Mbit)
4.6 - 4.11
Working
Realtek
RTL8139C+
3.14
Works
Realtek
RTL8139D
3.x
Some work, others don't. Check for yourself.
Realtek
RTL-8139/8139C/8139C+ (rev: 16)
4.9 & 4.10
Works, fine!
Realtek
RTL-8029(AS) (rev: 0)"
4.9 & 4.10
Works, fine!
ZNYX
ZX346Q
3.27
Works
VIA
VT6102 [Rhine-II] (rev: 67)"
4.9 & 4.10
Works, fine!
x86 Systems
Model
ROS version
Result
Dell Optiplex GX1
2.9.x-3.0
Intel onboard/cpu 450-600Mhz, eth:3com, best for wirless stations; uptime over 200d, no
problems at all.
Compaq Presario
2282
2.9.43
With 3c905 [Boomerang], no apparent problems
Dell GX100
2.9.x - 3.7
Intel onboard, 2 free pci, Intel cpu
Dell GX240
2.9.x - 3.7
Intel onboard, 2 free pci, Intel cpu, IDE HDD.
Dell GX260
2.9.x - 3.7
Intel onboard, 2 free pci, Intel cpu, IDE HDD.
Dell GX270
2.9.x - 3.7
Intel onboard, 2 free pci, Intel cpu. IDE HDD.
Dell GX280
2.9.x - 3.7
Intel onboard, 2 free pci, Intel cpu, SATA HDD.
Dell Dimension
XPS GEN 3
2.9.x
Lan Onboard, 4 free pci, Intel cpu , SATA HDD ( Excellent Stability )
Dell Inspiron
Desktop 518
2.9.x - 3.7
After netinsall stuck on "loading system"
Dell PowerEdge
860
3.x
1U Rackmount, 2x Broadcom Gigabit onboard, 1x Intel CPU (many options), 1 PCI/1 PCIe
or 2 PCIe riser options, SATA HDD ONLY. (some issues with floppy netinstall)
Dell PowerEdge
R200
Severe stability and clock issues with non-current ROS. Works like a top on 3.19 though.
>= 3.19
Also, if using an SATA-to-CF converter, the license key for the CF card in an R200 will only
recommended
transfer to other R200's without Mikrotik reissuing it.
Dell PowerEdge
2950
3.x
2U Rackmount, Optional Redundant Power Supplies, 2x Broadcom Gigabit onboard, 2x
Intel CPU (many options), 2- 8xPCIe & 1- 4xPCIe Standard (other risers available), SATA
HDD ONLY, 2x internal USB - MUST SPECIAL ORDER WITHOUT RAID CONTROLLER.
(some issues with floppy netinstall)}
HP Proliant
DL380 G5
3.17
Works, but only if installed from CDROM (Netinstall to Windows mounted HDD causes
issues)
Asus EEE PC 701
3.x
SFF Laptop, 1x10/100 ethernet (Not detected), Stock Wireless unsupported (AR5007E In
Mini-PCIX slot), 630/900Mhz processor, 512MB RAM, 4GB SSD (Not detected), USB2.0
Bootable, SDHC Reader functions as a USB Stick
Dell PowerEdge
SC1425
3.x
Rackmount, Intel Xeon 2.8 1MB 800FSB, 1024MB DDR2 PC3200 ECC, 2x Intel 82541GI
Gigabit Ethernet, HD150gb SATA, USB works, very stable
Fujitsu Siemens
Primergy
RX100S5
3.7, 3.22
Can Install from Netinstall with RAID (LSI) Controller enable. Can't install from CD and
Netinstall with only SATA or PATA mode. But NOT RUN
www.edcwifi.com
source : Mikrotik Wikipedia
4 of 9
www.mikrotikchina.cn
Toshiba Magnia
SG20
www.mikrotikchina.com
CPU Celeron, VIA chipsets, onboard LAN Realtek and Intel, IDE HDD, PCMCIA tested with
Orinoco Silver, miniPCI LT WinModem not work
2.9.44
Embedded Controllers
ROS
version
Model
Result
WRAP.1E-2
2.9.51, 3.7
3 Ethernet, 1 miniPCI, 128 MB - Working
WRAP.2E
2.9.51, 3.7,
3.9, 3.10
1 Ethernet, 2 MiniPCI, 128 MB - Work fine
ALIX 2-2
2.9.48
2 Ethernet, 2 miniPCI - Working
Adlink cPCI-6770 Low
Power Pentium III
2.9 and 3.0
CompactPCI CPU Module - Working, excellent performance!
Advantech PCA-6751
2.9.49
Working
Soekris 4801-50
2.9.48
3 Ethernet, 128MB, CF 512MB - Working
Soekris 4826-48
3.10
233 Mhz CPU, 128 Mbyte SDRAM, 1 Ethernet, 1 Serial, 256 Mbyte CF Flash, 2
Mini-PCI sockets, PoE. Limited power available/runs only 1 high power card (@26dB)
along with another lower power card (@17dB)
Soekris net4801-48/50
+ lan1641
3.22
All 7 (3+4) ethernet works, USB works (tested with Huawei 3G modem), extra serial
port works. And RouterOS installed on CF card.
ALIX 2C0
2.9,3.0
2 Ethernet, 2 miniPCI ,128Mb 433Mhz Amd Geode- Working Perfect
ALIX 2C1
2.9,3.0
2 Ethernet, 2 miniPCI ,128Mb 433Mhz Amd Geode- Working Perfect
ALIX 2C3
2.9,3.0
2 Ethernet, 2 miniPCI ,256Mb 500Mhz Amd Geode- Working Perfect
ALIX 3C1
2.9,3.0
2 Ethernet, 2 miniPCI ,128Mb 433Mhz Amd Geode- Working Perfect
ALIX 3C2
2.9,3.0
2 Ethernet, 2 miniPCI ,256Mb 500Mhz Amd Geode- Working Perfect
3G cards
Model
AirPrime/Sierra PC 5220!
ROS
version
Result
v3
AnyData ADU E100A
(aka "USB Wireless HSDPA/UMTS 2.1GHz
GSM/GPRS/EGPRS 900/17000MHz/CDMA 1x EVDO
v3.14
Rev.A")
AnyData ADU 500A USB
(aka "USB Wireless HSDPA/UMTS 2.1GHz
GSM/GPRS/EGPRS 900/1800MHz/CDMA 1x EVDO
v3.14
Rev.A")
Audiovox PC5220 CDMA Dual Band 1XEV-DO PC
Card
v3
C-motech CNU-680 CDMA 1x EV-DO 450Mhz USB
Modem (used by Triatel)
v3.22
Dell 5520
v3
Ericsson_F3507g_Mobile_Broadband_Module
V3.28
Huawei E226 USB modem,
3.25
Huawei E220 USB modem, E200BIS
3.0rc8
Huawei E169 USB modem (used by Tele2)
3.22
Huawei E180 USB modem
3.20
Huawei E1550
v3.26
Huawei E1553 (USB)
v4.6
Siemens M20
v3.28
Huawei Mobile Connect Model E620 (3G);
v3
Kyocera KPC650
v3
Novatel EU740
v3
Novatel EU870
v3
Novatel EV620 CDMA/EV-DO
v3
Novatel Merlin ES620 / Merlin ES720 / Ovation
U720
v3
Novatel Merlin ES620 SM Bus
v3
Novatel Merlin S720 (HSDPA);
v3
Set init string AT+CFUN=1, data channel and info channel to 3.
www.edcwifi.com
source : Mikrotik Wikipedia
5 of 9
www.mikrotikchina.cn
Novatel Merlin XU870 HSDPA/3G
www.mikrotikchina.com
v3
Novatel U730 (Wireless HSDPA Modem)
v3
Novatel Wireless CDMA card
v3
Option Fusion UMTS Quad-GPRS (Vodafone
Globetrotter);
v3.4
Option Globetrotter HSDPA USB (aka Teltonika
ModemUSB/H7.2 U3G150)
v3
Option Qualcomm 3G WCDMA Model
M00201-10886 miniPCI-e
v3.27
works also in RouterBOARD with miniPCI-e slot and SIM slot (SIM
slot required)
Option Qualcomm 3G CDMA Model M00301
(GTM380) miniPCI-e
v3.28
works in RouterBOARD 411U with miniPCI-e slot and SIM slot
(SIM slot required). Set data channel and info channel to 3.
Option Qualcomm 3G CDMA Model M00401
(GTM382) miniPCI-e
works in RouterBOARD 411U with miniPCI-e slot and SIM slot.
Set data channel and info channel to 3. Performance on CZ O2 in
v3.28 &
Prague HSDPA connection about 2.6Mbit download and 0.7Mbit
v4.6
upload. Latency between 100-300ms. Application based on this
on http://carlive.cz [1] (http://carlive.cz) .
Ericsson 3G F3607gw miniPCI-e
v3.28
Sierra Aircard 595
v3
Sierra Aircard 595U USB Sprint Card
v3
Sierra Wireless AirCard 580
v3
Sierra Wireless AirCard 595
v3
Sierra Wireless AirCard 597E
v3
Sierra Wireless AirCard 597E
v3
Sierra Wireless AirCard 875
v3
Sierra Wireless AirCard 880
v3.8
Sierra Wireless AirCard 880 E
v3.8
Sierra Wireless AirCard 881
v3.8
Sierra Wireless AirCard 881 E
v3.8
Sierra Wireless EM5625
v3
Sierra Wireless MC5720
v3
Sierra Wireless MC5720
v3
Sierra Wireless MC5725
v3
Sierra Wireless MC8755
v3
Sierra Wireless MC8755 for Europe
v3
Sierra Wireless MC8765
v3
Sierra Wireless MC8775
v3
Sierra Wireless MC8780
v3.8
Sierra Wireless MC5725
v3.18
Sierra Wireless MC5727
v3.18
Sierra Wireless MC8785
v3.18
Sierra Wireless MC8790
v3.18
Sierra Wireless MC8790
v3.18
Sierra Wireless MC8781
v3.8
Sierra Wireless Sierra 598 (Sprint) USB
v3.x
Sierra Wireless MP3G - EVDO
v3.8
works in RouterBOARD 411U with miniPCI-e slot and SIM slot
(SIM slot required). Set data channel and info channel to 2. Set
init string AT+CFUN=1
Users have reported that the device doesn't show up after
shutdown, reboot is required. Init-string:
ATE0V1&D2&C1S0=0+IFC=2,2;AT+CGDCONT=1,"IP","apnstring"; - where the apn-string is your correct APN. A reboot can
be required after settings are changed, to make it working. Data
and Info channel are 0.
Sierra Wireless MP3G - UMTS/HSPA
v3.8
Sierra Wireless Compass 885 (USB)
v3.28
Silicon Labs MobiData GPRS USB Modem
v3.22
Sprint U301/301U 4G wireless card
v4.6
C-MOTECH Co, FW301DOWMX, QUALCOMM Patch 33504
Sprint U300/300U 4G wireless card
v4.6
C-MOTECH Co, FW301DOWMX, QUALCOMM Patch 33504
Verizon Express Network PC5220 (AirPrime 5220)
v3
ZTE AC8700
v3.6
ZTE MF620 / MF622
v3
ZTE MF620 / MF622 (3G)
v3.6
ZTE MF668
v4.5
T-Mobile (Germany) Web´n´Walk Box Micro
(Huawei E220)
v3.x
Vodafone (Germany) Easybox 2 (Huawei E220)
v3.x
AKA Telecom New Zealand's new XT network. Works a treat.
www.edcwifi.com
USB
source : Mikrotik Wikipedia
6 of 9
www.mikrotikchina.cn
O2 (Germany) Surfbox Mini (Huawei E220)
v3.x
E-Plus & Base (Germany) USB Minimodem
(Huawei E220)
v3.x
Huawei E600
v3.15
Novatel Merlin V640/XV620
v3.15
Novatel Merlin V620/S620
v3.15
Novatel Merlin EX720/V740/X720
v3.15
Novatel Merlin V720/S720/PC720
v3.15
Novatel Merlin XU870 HSDPA/3G
v3.15
Novatel X950D
v3.15
Novatel ES620/ES720/U720/USB720
v3.15
Novatel E725/E726
v3.15
Vodafone EU740/Novatel non-Vodafone EU740
v3.15
Vodafone K3565/Huawei E160
v3.23
Novatel EU850D/EU860D/EU870D
v3.15
Novatel MC930D/MC950D
v3.15
Novatel MC727/U727
v3.15
Novatel Expedite EV620 CDMA/EV-DO
v3.15
Novatel Expedite EU740 HSDPA/3G, Dell Wireless
5500 Mobile/Dell Wireless 5505 Mobile
v3.15
Novatel Expedite E720 CDMA/EV-DO
v3.15
Novatel Expedite ET620 CDMA/EV-DO
v3.15
Onda H600/ZTE MF330
v3.15
BP3-USB & BP3-EXT HSDPA
v3.15
ZTE MY 39 (MSM 6500 based)
v3.20
Cricket A600
v3.26
Globetrotter HSDPA Modem Option N.V.
v3.26
Sony Ericsson MD300
v3.26
ZTE MF 626
v3.26
ZTE MF 627
v3.26
Pantech / UTStarcom UM175
v3.27
Novatel U760
v3.30
ZTE K3565-Z
v4.4
Novatel Expedite EV620
v4.5
Novatel MC760 VMU
v4.5
Franklin Wireless FW300DOWMX
v4.5
Huawei EC1260
v4.5
Vodafone K3520-Z
v4.6
Vodafone K3765
v4.6
Telstra 3G Elite
v5.x
Vodafone Huawei K4505
v5.x
Vertex VW 110
v5.x
www.mikrotikchina.com
On Alltel's CDMA EVDO RevA network average 700-800kbps up
and 2.4-2.8Mbps down
Revision: BD_P673A2V1.0.0B09
Memory cards
NB! New flash cards need always formatting!
Legend:
V - works
X - doesn't work
? - not tested
NA - not available for this RB
Model
Type
RB600
RB1000
RB433AH
RB450G
PQI 4GB 120x HiSpeed
CF
X
?
NA
2GB Transcend 133x
CF
X
?
NA
?
?
2GB Kingston 133x (Elite Pro, code CF/2GB-S2)
CF
V
?
NA
?
4GB Kingston 133x (Elite Pro)
CF
?
V
NA
?
4GB Kingston CF/4GBIN
CF
X
?
NA
?
8GB A-Data Speedy G08GNMC7B0095
CF
V
V
NA
?
16GB A-Data Speedy
CF
V
V
NA
?
4GB Apacer Photo Steno IV 300X
CF
X
X
NA
?
1GB Sandisk Ultra II BB05024GA
CF
V
V
NA
?
www.edcwifi.com
source : Mikrotik Wikipedia
7 of 9
www.mikrotikchina.cn
www.mikrotikchina.com
2GB Sandisk Ultra II
CF
?
V
NA
?
8GB Sandisk Ultra II
CF
?
V
NA
?
8GB SanDisk Extreme III (200X,30MB/s)
CF
?
V
NA
?
2.5GB Seagate ST1 (ST625211CF)
CF microdrive
V
V
NA
?
8GB Seagate ST1
CF microdrive
V
V
NA
?
64MB Nokia
microSD
NA
NA
?
V
512MB Kingston
microSD
NA
NA
V
?
1GB Apacer
microSD
NA
NA
V
?
1GB Kingston (SDC/1GB)
microSD
NA
NA
?
X
2GB Kingston
microSD
NA
NA
X
X
2GB Traxdata
microSD
NA
NA
?
V
4GB Apacer SDHC (class 6)
microSD
NA
NA
V
X
4GB Axiz
microSD
NA
NA
V
?
4GB Kingston
microSD
NA
NA
V
?
4GB Kingston SDHC (C04G JAPAN class 4)
microSD
NA
NA
V
?
4GB Transcend SDHC
microSD
NA
NA
V
?
4GB Sandisk Mobile Ultra Micro SDHC (with card reader)
microSD
NA
NA
?
V
8GB Sandisk SDHC (0733702482DLE)
microSD
NA
NA
V
V
8GB Sandisk Mobile microSDHC (SDSDQ-8192-A11M)
microSD
NA
NA
?
V
8GB Sandisk Mobile Ultra SDHC (Class 6)
microSD
NA
NA
?
V
8GB Kingston SDHC (Class 4)
microSD
NA
NA
V
X
8GB ADATA micro SDHC (AUSDH8GCL6) (Class 6)
microSD
NA
NA
?
V
16GB Sandisk micro SDHC (SDSDQ-16384-P36M) class 2
microSD
NA
NA
NA
X
16GB Sandisk micro SDHC (0835B03279DQ) class 2
microSD
NA
NA
V
V
Note: Pushing the "Kingston SDHC 8GB card" all the way into the socket caused the card not to work properly! It had to be
pulled out ~1mm for it to work!
802.11a/b/g wireless cards
research papers (http://www.besttermpaper.com/)
Form
factor
Model
Platform
ROS
Result
TechnicLan TMP-5414A (http://www.techniclan.com
/Wireless_mPCI_TMP5414A_11abg_108Mbps_Atheros_solution,p,74.html)
miniPCI
All
2.9 / 3.x
RouterBOARDs
/ 4.x
Perfect, Stable
Compex WLM54AG-20 (http://www.compex.com.sg
/fullDescription.aspx?pID=23)
miniPCI
RB1xx / RB3xx /
2.9 / 3.x
RB4xx / RB5xx /
/ 4.x
RB6xx / x86
Perfect, Stable
Compex WLM54A-26 (http://www.compex.com.sg
/fullDescription.aspx?pID=25)
miniPCI
RB1xx / RB3xx /
2.9 / 3.x
RB4xx / RB5xx /
/ 4.x
RB6xx / x86
Perfect, Stable
SparkLAN WMIA-165G
miniPCI
RB1xx / RB3xx /
2.9 / 3.x
RB4xx / RB5xx /
/ 4.x
RB6xx / x86
Perfect, Stable
SparkLAN WMIA-166AG
miniPCI
RB1xx / RB3xx /
2.9 / 3.x
RB4xx / RB5xx /
/ 4.x
RB6xx / x86
Perfect, Stable
SparkLAN WMIA-166AGH
miniPCI
RB1xx / RB3xx /
2.9 / 3.x
RB4xx / RB5xx /
/ 4.x
RB6xx / x86
Perfect, Stable
Alfa AWPCI 085 H
miniPCI
RB1xx/RB333
/RB4xx/x86
2.9&3.x
All just perfect
TP-Link TL-WN550/551
PCI
x86
2.9&3.x
Perfect 19dB rated, stable at
21
TP-Link TL-WN650/651
PCI
x86
2.9&3.x
Perfect 19dB rated, stable at
21. Unstable with
compression activated
D-Link AG530 a/b/g (both rev.A1 and A2)
PCI
x86
2.9&3.x
Perfect. Works perfect, in
both 2.4 and 5.x GHz
D-Link DWL-G510
PCI
x86
only
2.9.x
tested
Perfect. Tested Rev A1
D-Link DWL-G520
PCI
x86
2.9.x &
3.x
Works well.
www.edcwifi.com
source : Mikrotik Wikipedia
8 of 9
www.mikrotikchina.cn
D-Link DWL-G520+A/RaLink 2591 Chipset
PCI
www.mikrotikchina.com
x86
4.9
NOT Work!
Gigabyte b/g GN-WI01GT
miniPCI-e
x86
3.x
Works also in RouterBOARDs
with miniPCI-e slot
Senao NL-2511CD EXT2
PCMCIA
x86&rb230
only
2.9x
tested
Perfect. Just about the most
sensitive card i used, in the
good sense. Only 11b.
Planet WL-8310
PCI
x86
only
2.9.x
tested
Perfect. Stability.
Netgear WG311T 108
PCI
x86
only
2.9x
tested
Perfect. stability
SMC SMCWPCIT-G
PCI
x86
3.x
tested
Perfect on A/B/G.
Wistron DCMA-81
miniPCI
x86,rb
2.9.xx,
3.xx
Perfect on A/B/G with or
without compression.
Wistron DCMA-82
miniPCI
rb
3.xx
Works on some RB, but on
2/3 of my RB433 it causes the
board to reboot when
enabled. Many other people
have had similar experiences.
Not recommended. Maybe OK
on 133
Senao NMP-8602
miniPCI
x86&rb411
2.9x,3.x
tested
Perfect on a/b/g
Dbii F20 (http://dbii.com/f20.html)
miniPCI
RB411 & RB433
3.x
tested
Perfect on B/G, too thick for 3
in rb433
Dbii F50 (http://dbii.com/f50.html)
miniPCI
RB411 & RB433
3.x
tested
Perfect on A, too thick for 3 in
rb433
Dbii F20-PRO (http://www.dbii.com/f20-PRO.html)
miniPCI
RB411 & RB433
3.x
tested
Perfect on B/G, too thick for 3
in rb433
Dbii F50-PRO (http://www.dbii.com/f50-PRO.html)
miniPCI
RB411 & RB433
3.x
tested
Perfect on A, too thick for 3 in
rb433
Ubiquiti XR2 (http://www.ubnt.com/products/xr2.php)
miniPCI
RB433
3.x
works as advertised, too
thick for 3 in rb433
Ubiquiti XR5 (http://www.ubnt.com/products/xr5.php)
miniPCI
RB433, x86
3.x
works as advertised, too
thick for 3 in rb433
Ubiquiti SR9 (http://www.ubnt.com/products/sr9.php)
miniPCI
RB433
3.x
works as advertised, thin
enough to load 3 in RB433
3.x
works as advertised, thin
enough to place cards above,
but antenna port may contact
cards below
Ubiquiti XR9 (http://www.ubnt.com/products/xr9.php)
miniPCI
RB411 & RB433
Valemount KXS30SG (http://www.staros.com
/documentation/KXS30SG%20Sell%20Sheet.pdf)
miniPCI
RB433
3.2 &
4.2
tested
B/G only, no A. Big heat sink
means card should be
installed on highest mount
when other cards being used.
High power consumption can
cause power problems,
otherwise works perfectly.
Zcomax XG-650 (http://www.zcomax.cz/Xg650.aspx)
miniPCI
RB112 & RB433
4.2 &
4.6
Not working (driver doesnt
work / exist). It has a TI
TNETW1130GVF chipset.
AR5BMB5
miniPCI
RB411,x86
3.xx, 4.3 Not working. Atheros chipset.
802.11n wireless cards
Form factor
Model
ROS
Result
SparkLAN WMIA-198N (http://store.dcsindo.com/interfaces/wireless-minipci/wmia198n.html)
miniPCI
4x, 5x
Perfect,
Stable
Compex WLM200N5-23 (http://www.compex.com.sg/fullDescription.aspx?pID=96)
miniPCI
4.0b3
Perfect,
Stable
Compex WLM200NX (http://www.compex.com.sg/fullDescription.aspx?pID=32)
miniPCI
4.0b3
Perfect,
Stable
RouterBOARD R2N (http://www.routerboard.com/prices.html)
miniPCI
4.0b3
works
RouterBOARD R52N (http://www.routerboard.com/prices.html)
miniPCI
4.0b3
works
TP-Link Wireless N (2T2R)
miniPCI
4.0b3
works
Ubiquiti SR71-A (http://www.ubnt.com/products/sr71a.php)
miniPCI
4.0b3
works
Ubiquiti SR71-A (http://www.ubnt.com/products/sr71a.php)
miniPCI
4.0b3
works
www.edcwifi.com
source : Mikrotik Wikipedia
9 of 9
www.mikrotikchina.cn
www.mikrotikchina.com
T1/E1
Model
Form factor
Farsite FarSync TE1
Platform
PCI
ROS
x86
3.15
Result
supported
Note: Since v3.15 RouterOS doesn't support any Sync/T1/E1 cards except select Farsite models
GPS
Model
EXAMPLE
Connection
USB
Platform
x86
ROS
3.30
Result
supported
Storage controllers (SAS/SCSI/RAID)
Post only tests since RouterOS v5beta5
Brand
EXAMPLE
Model
model
Motherboard
x86
RouterOS
v5beta5
Works / Doesn't
Yes,works
www.edcwifi.com
source : Mikrotik Wikipedia