Metered Commercial
FLW1526C
Para bajar una copia de estas instrucciones
en español, visite www.alliancelaundry.com.
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
www.alliancelaundry.com
Part No. 802734ENR7
January 2014
Installation/Operation
Frontload Washers
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property
damage.
W030
NOTE: The WARNING and IMPORTANT instructions appearing in this manual are not meant to cover all
possible conditions and situations that may occur. It must be understood that common sense, caution, and
carefulness are factors which cannot be built into these washers. These factors MUST BE supplied by the
person(s) installing, maintaining, or operating the washer.
Always contact the distributor, service agent, or the manufacturer about any problems or conditions you do not
understand.
802734ENR1
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
1
Table of
Contents
Safety Information..............................................................................
Explanation of Safety Messages...........................................................
Important Safety Instructions ...............................................................
4
4
4
Installation...........................................................................................
Dimensions and Specifications.............................................................
Before You Start ...................................................................................
Tools ................................................................................................
Installing the Washer ............................................................................
Step 1: Position Washer Near Installation Area ..............................
Step 2: Position and Level the Washer ............................................
Step 3: Connect Fill Hoses...............................................................
Step 4: (Non-Gravity Drain Models Only)
Connect Drain Hose to Drain Receptacle.......................................
Step 5: (Gravity Drain Models Only)
Connect Drain Outlet to Drain System...........................................
Step 6: Remove the Shock Sleeves and Shipping Brace .................
Step 7: Wipe Out Inside of Wash Drum ..........................................
Step 8: Plug In the Washer...............................................................
Step 9: Check Installation ................................................................
Vending.................................................................................................
Meter Case .......................................................................................
Slide Extension Assembly – Models through Serial No. 1211........
Slide Extension Assembly – Models Starting Serial No. 1211 .......
Models Prepped for Card Reader.....................................................
6
6
7
7
8
8
8
9
12
13
14
14
15
16
16
16
17
19
Operation.............................................................................................
Operation Instructions for Coin Slide Operated Washers ....................
Step 1: Load Laundry.......................................................................
Step 2: Close Loading Door.............................................................
Step 3: Add Laundry Supplies .........................................................
Step 4: Set Fabric Selector ...............................................................
Step 5: Set WASH/RINSE Temperatures........................................
Step 6: Insert Money ........................................................................
Indicator Lights ................................................................................
Rapid Advance.................................................................................
Operation Instructions for MDC Washers............................................
Step 1: Load Laundry.......................................................................
Step 2: Close Loading Door.............................................................
Step 3: Add Laundry Supplies .........................................................
Step 4: Set Fabric Selector and Wash Temperature.........................
Step 5: Insert Coin(s) or Card ..........................................................
Step 6: Start Washer.........................................................................
Indicator Lights ................................................................................
20
20
20
20
21
21
21
21
22
22
23
23
23
24
24
25
25
26
11
© Copyright 2014, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
2
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
802734ENR1
Operation Instructions for NetMaster Washers ....................................
Step 1: Load Laundry.......................................................................
Step 2: Close Loading Door.............................................................
Step 3: Add Laundry Supplies .........................................................
Step 4: Set Fabric Selector ...............................................................
Step 5: Set Wash Temperature.........................................................
Step 6: Insert Coin(s) or Card ..........................................................
Step 7: Start Washer.........................................................................
Indicator Lights ................................................................................
27
27
27
27
28
28
28
29
29
Maintenance ........................................................................................
User-Maintenance Instructions.............................................................
Lubrication .......................................................................................
Cold Weather Care...........................................................................
Care of Your Washer .......................................................................
Cleaning Glass Sealing Area ...........................................................
Replacing Hoses...............................................................................
Filter Screens ...................................................................................
Vacations and Extended Non-Use ...................................................
Reinstallation of Shipping Materials ...............................................
Cleaning Foreign Object Trap .........................................................
30
30
30
30
30
30
30
30
30
31
31
Troubleshooting .................................................................................. 32
Contact Information........................................................................... 34
Installer Checklist................................................................ Back Cover
802734ENR1
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
3
Safety Information
Explanation of Safety Messages
Important Safety Instructions
Throughout this manual and on machine decals, you
will find precautionary statements (“DANGER,”
“WARNING,” and “CAUTION”) followed by specific
instructions. These precautions are intended for the
personal safety of the operator, user, servicer, and
those maintaining the machine.
(Save These Instructions)
DANGER
Indicates an imminently hazardous
situation that, if not avoided, will cause
severe personal injury or death.
WARNING
Indicates a hazardous situation that, if not
avoided, could cause severe personal
injury or death.
CAUTION
Indicates a hazardous situation that, if not
avoided, may cause minor or moderate
personal injury or property damage.
Additional precautionary statements (“IMPORTANT”
and “NOTE”) are followed by specific instructions.
IMPORTANT: The word “IMPORTANT” is used
to inform the reader of specific procedures where
minor machine damage will occur if the procedure
is not followed.
NOTE: The word “NOTE” is used to communicate
installation, operation, maintenance or servicing
information that is important but not hazard
related.
WARNING
To reduce the risk of fire, electric shock,
serious injury or death to persons when
using your washer, follow these basic
precautions:
W023
1. Read all instructions before using the washer.
2. Install the washer according to the
INSTALLATION INSTRUCTIONS. Refer to the
GROUNDING INSTRUCTIONS in the
INSTALLATION manual for the proper
grounding of the washer. All connections for
water, drain, electrical power and grounding must
comply with local codes and be made by licensed
personnel when required. Do not do it yourself
unless you know how!
3. Do not install or store the washer where it will be
exposed to water and/or weather.
4. Do not add the following substances or textiles
containing traces of the following substances to
the wash water: gasoline, kerosene, waxes,
cooking oils, vegetable oils, machine oils, drycleaning solvents, flammable chemicals, thinners
or other flammable or explosive substances.
These substances give off vapors that could
ignite, explode or cause the fabric to catch on fire
by itself.
5. Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for two weeks or more. HYDROGEN GAS
IS EXPLOSIVE. If the hot water system has not
been used for such a period, before using a
washing machine or combination washer-dryer,
turn on all hot water faucets and let the water
flow from each for several minutes. This will
release any accumulated hydrogen gas. THE
GAS IS FLAMMABLE, DO NOT SMOKE OR
USE AN OPEN FLAME DURING THIS TIME.
6. To reduce the risk of an electric shock or fire, DO
NOT use an extension cord or an adapter to
connect the washer to the electrical power
source.
4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
802734ENR7
Safety Information
7. Do not allow children to play on or in the washer.
Close supervision of children is necessary when
the washer is used near children. This appliance
is not intended for use by persons (including
children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning the use of
the appliance by a person responsible for their
safety. This is a safety rule for all appliances.
8. Do not reach into the washer if the washtub is
moving.
9. Never operate the washer with any guards, panels
and/or parts removed or broken. DO NOT tamper
with the controls or bypass any safety devices.
10. DO NOT operate individual units if they have
been separated from a stack unit.
11. Use your washer only for its intended purpose,
washing clothes. Always follow the fabric care
instructions supplied by the garment
manufacturer.
12. Always read and follow manufacturer’s
instructions on packages of laundry and cleaning
aids. To reduce the risk of poisoning or chemical
burns, keep them out of the reach of children at
all times (preferably in a locked cabinet). Heed
all warnings or precautions.
13. Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
14. Loading door MUST BE CLOSED any time the
washer is to fill, tumble or spin. DO NOT bypass
the loading door switch by permitting the washer
to operate with the loading door open.
802734ENR7
15. Be sure water connections have a shut-off valve
and that fill hose connections are tight. CLOSE
the shut-off valves at the end of each wash day.
16. Keep your washer in good condition. Bumping or
dropping the washer can damage safety features.
If this occurs, have your washer checked by a
qualified service person.
17. Do not repair or replace any part of the washer, or
attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that you understand and have the
skills to carry out. ALWAYS disconnect the
washer from electrical supply before attempting
any service.
18. Disconnect the power cord by grasping the plug,
not the cord. If the supply cord is damaged, it
must be replaced by a special cord or assembly
available from the manufacturer or its service
agent.
19. Before the washer is removed from service or
discarded, remove the lid or door to the washing
compartment.
20. Failure to install, maintain, and/or operate this
washer according to the manufacturer’s
instructions may result in conditions which can
produce bodily injury and/or property damage.
NOTE: The WARNING and IMPORTANT
SAFETY INSTRUCTIONS appearing in this
manual are not meant to cover all possible
conditions and situations that may occur. Common
sense, caution and care must be exercised when
installing, maintaining, or operating the washer.
Always contact your dealer, distributor, service agent
or the manufacturer about any problems or conditions
you do not understand.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5
Installation
Dimensions and Specifications
Coin Slide Models
21.56 in. (54.76 cm)
36 in. (91.44 cm)
14.6 in.
(37.08 cm)
13.1 in.
(33.3 cm)
31.1 in. (79 cm)
29.6 in. (75.1 cm)
24 in.
(61.0 cm)
Standard Capacity Meter Case
43 in. (109.2 cm)
High Capacity Meter Case
43.875 in. (111.44 cm)
Coin Slide Models 40.19 in. (102.08 cm)
Electronic Control Models 38.19 in. (97 cm)
Electronic Control Models
22.06 in. (56.03 cm)
26.875 in. (68.3 cm)
28 in. (71.1 cm)
2 in.
(5.1 cm)
1.5 in.
(3.8 cm)
FLW2201N
MODELS EQUIPPED WITH DRAIN HOSE
FLW2201N
Coin Slide Models
21.56 in. (54.76 cm)
28 in. (71.1 cm)
4.1 in.
(10.41cm)
1.5 in.
(3.8 cm)
36 in. (91.44 cm)
14.6 in.
(37.08 cm)
13.1 in.
(33.3 cm)
31.1 in. (79 cm)
29.6 in. (75.1 cm)
24 in.
(61.0 cm)
Standard Capacity Meter Case 43 in. (109.2 cm)
High Capacity Meter Case 43.875 in. (111.44 cm)
Coin Slide Models 40.19 in. (102.08 cm)
Electronic Control Models 38.19 in. (97 cm)
Electronic Control Models
22.06 in. (56.03 cm)
4.2 in.
(10.67cm)
26.875 in. (68.3 cm)
1
MODELS WITH GRAVITY DRAIN
FLW2202N
1
6
1.5 in. (3.81 cm) Inside Diameter
1.86 in. (4.72 cm) Outside Diameter
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
802734ENR7
Installation
Before You Start
Tools
For most installations, the basic tools you will need
are:
1
2
NOTE: If the washer is delivered on a cold day
(below freezing), or is stored in an unheated room
or area during the cold months, do not attempt to
operate it until the washer has had a chance to
warm up.
NOTE: Install dryer before washer. This allows
room for attaching exhaust duct.
3
4
NOTE: Some moisture in the wash drum is normal.
Water is used during testing at the manufacturer.
5
D074I
1
2
3
4
5
Wrench
Screwdriver
Pliers
Socket Wrench
Level
Figure 1
802734ENR7
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
7
Installation
Installing the Washer
Step 2: Position and Level the Washer
Step 1: Position Washer Near Installation
Area
Move washer so that it is within 4 feet (1.2 meters) of
the desired area of installation.
NOTE: For best performance and to minimize
vibration or movement, install washer on a solid,
sturdy and level floor. Some floors may need to be
reinforced, especially on a second floor or over a
basement. Do not install the washer on carpeting,
soft tile, a platform or other weakly supported
structures.
WARNING
Washers elevated above floor level must
be anchored to that elevated surface,
base or platform. The material used to
elevate the washer should also be
anchored to the floor to ensure that the
washer will not walk or that the washer
can not be physically pulled, tipped or
slid from its installed position. Failure to
do so may result in conditions which can
produce serious injury, death and/or
property damage.
W306
Position washer so it has sufficient clearance for
installation and servicing.
NOTE: Use of the dispenser drawer or washer door
as a handle in the transportation of the washer may
cause damage to the dispenser or door.
Place washer in position on a solid, sturdy and level
floor. Installing the washer on any type of carpeting,
soft tile, a platform or other weakly supported
structures is not recommended.
Place a level on the cabinet top and check if the
washer is level from side to side and front to back.
NOTE: Level must rest on raised portion of top
panel. Refer to Figure 3.
If washer is not level, tilt washer to access the front
and rear leveling legs. For easier access to leveling
legs, prop up washer with a wooden block. Refer to
Figure 3. Loosen 7/8 in. locknut and adjust legs until
the washer is level from side to side and front to back
(using a level). Washer should not rock.
H135I
H135I
Figure 2
8
Tighten the locknuts securely against the washer
base using the 7/8 in. wrench. If the locknuts are not
tight, washer will move out of position during
operation.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
802734ENR7
Installation
NOTE: DO NOT slide washer across floor if the
leveling legs have been extended, as legs and base
could become damaged.
Remove rubber feet from accessories bag and place on
all four leveling legs.
Verify that unit doesn’t rock.
3
2
1
Water Supply
Water supply faucets must fit standard 3/4 inch
(19.1 mm) female garden hose couplings. DO NOT
USE SLIP-ON OR CLAMP-ON CONNECTIONS.
Water supply faucets should be readily accessible to
permit turning them off when washer is not being
used.
Recommended cold water temperature is 60° to 80°
Fahrenheit (16° to 27° Celsius). Recommended
maximum hot water temperature is 125° Fahrenheit
(51° Celsius). Warm water is a mixture of hot and cold
water. Warm water temperature is dependent upon
water temperature and pressure of both the hot and
cold water supply lines.
WARNING
6
5
4
FLW2125N
To prevent personal injury, avoid contact
with inlet water temperatures higher than
125° Fahrenheit (51° Celsius) and hot
surfaces.
W748
Mixing Valve Flow Rates
FLW2125N
1
2
3
4
5
6
Leveling Leg
Washer Base
Level
Wood Block
Locknut
Rubber Foot
HOT
Pressure liters per minute
(psi)
(gallons per
minute)
Figure 3
Step 3: Connect Fill Hoses
WARNING
Under certain conditions, hydrogen gas
may be produced in a hot water system
that has not been used for two weeks or
more. HYDROGEN GAS IS EXPLOSIVE. If
the hot water system has not been used
for such a period and before using the
washer, turn on all hot water faucets and
let the water flow from each for several
minutes. This will release any
accumulated hydrogen gas. The gas is
flammable. Do not smoke or use an open
flame during this time.
W029
802734ENR7
COLD
liters per minute
(gallons per
minute)
20
6 (1.6)
9.4 (2.5)
40
8.2 (2.2)
13 (3.4)
60
9.9 (2.6)
14.5 (3.8)
100
9.6 (2.5)
15.9 (4.2)
120
9.8 (2.6)
15.9 (4.2)
Water pressure must be a minimum of 20 to a
maximum of 120 pounds per square inch (138 to 827
kPa) static pressure measured at the faucet.
NOTE: Water pressure under 20 pounds per
square inch (138 kPa) will cause an extended fill
time in the washer and may not properly flush out
the detergent dispenser.
Turn on the water supply faucets and flush the lines for
approximately two minutes to remove any foreign
materials that could clog the screens in the water
mixing valve.
NOTE: When installing in newly constructed or
renovated building, it is very important to flush the
lines since build-up may have occurred during
construction.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9
Installation
Connecting Hoses
2
Insert each filter screen into the end of each fill hose
that will connect to the water supply faucet. The screen
must be facing outward. Refer to Figure 4.
3
1
Insert each plain rubber washer into the other end of
each fill hose that will connect to the water mixing
valve at the rear of the washer. Refer to Figure 4.
Thread hose couplings onto valve connections fingertight, then approximately 1/4 turn with pliers.
IMPORTANT: DO NOT cross thread or
overtighten couplings.
WATER
MIXING
VALVE
4
Turn water on and check for leaks. If leaks are found,
retighten the hose couplings. Continue tightening and
rechecking until no leaks are found.
1
FLW1977N
1
2
3
4
Water Supply Faucets
Hot Water Connection
Cold Water Connection
Fill Hoses
Figure 5
COLD
HOT
3
2
4
IMPORTANT: Turn off water supply faucets after
check-out and demonstration. Owner should turn
off water supply whenever there will be an
extended period of non-use.
NOTE: Longer fill hoses are available (as optional
equipment at extra cost) if the hoses supplied with
the washer are not long enough for the installation.
Order hoses as follows:
No. 20617 Fill Hose (8 feet) (2.44 m)
No. 20618 Fill Hose (10 feet) (3.05 m)
TLW1976N
1
2
3
4
Faucet
Fill Hoses
Plain Rubber Washer
Filter Screens
Figure 4
IMPORTANT: Hoses and other natural rubber
parts deteriorate after extended use. Hoses may
develop cracks, blisters or material wear from the
temperature and constant high pressure they are
subjected to.
All hoses should be checked on a monthly basis for
any visible signs of deterioration. Any hose showing
the signs of deterioration listed above should be
replaced immediately. All hoses should be replaced
every five years.
10
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
802734ENR7
Installation
Risers
Risers (or air cushions) may have to be installed if the
pipes knock or pound when flow of water stops. The
risers are more efficient when installed as close as
possible to the water supply faucets (refer to
Figure 6).
1
Step 4: (Non-Gravity Drain Models Only)
Connect Drain Hose to Drain Receptacle
Remove the drain hose from its shipping position on
the rear of the washer by removing the shipping tape.
IMPORTANT: Drain receptacle must be capable of
handling a minimum of 1-3/8 inch (3.5 cm) outside
diameter drain hose.
1
2
W005I
W005I
1
2
Risers (Air Cushions)
Water Supply Faucets
Figure 6
FLW1978N
1
Shipping Tape
Figure 7
802734ENR7
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
11
Installation
Standpipe Installation
Step 5: (Gravity Drain Models Only)
Connect Drain Outlet to Drain System
Place the drain hose into the standpipe.
Remove the beaded tie-down strap from accessories
bag and place around standpipe and drain hose and
tighten strap to hold hose to standpipe. Refer to
Figure 8. This will prevent the drain hose from
dislodging from drain receptacle during use.
Remove drain fitting (four inches long) and hose
clamp from accessories bag. Insert drain fitting into
drain outlet hose. Clamp hose and fitting.
Connect the drain fitting to a vented drain system
using a flexible connection (obtain locally). Inside
diameter of fitting is 1.53 in. (3.89 cm) and outside
diameter is 1.66 in. (4.22 cm). The drain system must
be vented to prevent an air lock or siphoning.
IMPORTANT: Increasing the drain hose length,
installing elbows, or causing bends will decrease
drain flow rates and increase drain times,
impairing machine performance.
24 TO 36 in.
(61 TO 91.44 cm)
RECOMMENDED
HEIGHT
1
FLW1979N
FLW1979N
1
Standpipe 2 in. (5.08 cm) or 1-1/2 in. (4 cm)
Figure 8
2
Drain Flow Rate
Drain Height
Flow Rate
liters per minute
(gallons per minute)
0.9 m (3 ft.)
31 (8.19)
1.5 m (5 ft.)
27.5 (7.27)
1.8 m (6 ft.)
23.9 (6.31)
2.1 m (7 ft.)
18.5 (4.89)
2.4 m (8 ft.)
10.6 (2.79)
1
FLW1980N
FLW1980N
1
2
Drain Trough
Drain Outlet Hose
Figure 9
12
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
802734ENR7
Installation
Step 6: Remove the Shock Sleeves and
Shipping Brace
4. Replace panel.
1. Remove panel.
FLW2272N
FLW2272N
Figure 13
FLW2269N
FLW2269N
Figure 10
2. Remove brace. Five bolts secure brace to
machine. For easier removal, remove in order
shown.
FLW2268N
FLW2268N
5
Figure 14
1
2
4
3
FLW2270N
Figure 11
3. Remove shock sleeves.
IMPORTANT: The shipping brace, bolts,
lockwashers and shock sleeves should be saved and
MUST be reinstalled whenever the unit is moved
more than four feet. Do not lift or transport unit
from front or without shipping materials installed.
Refer to the User’s Guide for proper instructions
on reinstalling the shipping materials.
IMPORTANT: DO NOT tip washer more than
6 inches (152.4 mm) in any direction after shipping
brace has been removed. Shock absorbers may
separate and damage to washer may result. For
leveling purposes, the washer may be tilted a
maximum of 6 inches (152.4 mm) in any direction.
FLW2271N
FLW2271N
Figure 12
802734ENR7
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
13
Installation
Step 7: Wipe Out Inside of Wash Drum
Before using washer for the first time, use an all-purpose
cleaner, or a detergent and water solution, and a damp
cloth to remove shipping dust from inside wash drum.
The washer is designed to be operated on a separate
branch, polarized, three-wire, effectively grounded,
120 Volt, 60 Hertz, AC (alternating current), circuit
protected by a 15 ampere fuse, equivalent fusetron or
circuit breaker.
The three-prong grounding plug on the power cord
should be plugged directly into a polarized three-slot
effectively grounded receptacle rated 110/120 Volts
AC (alternating current) 15 Amps. Refer to Figure 16
to determine correct polarity of the wall receptacle.
2
3
1
120±12
V.A.C.
0 V.A.C.
FLW2126N
FLW2126N
120±12
V.A.C.
Figure 15
4
5
Step 8: Plug In the Washer
Electrical Requirements
(120 Volt, 60 Hertz with 3-Prong Grounding Plug)
Standard 120 Volt, 60 Hertz
3-Wire Effectively
Grounded Circuit
NOTE: The wiring diagram is located in the
control hood.
DRY2022N
WARNING
To reduce the risk of fire, electric shock,
serious injury or death, all wiring and
grounding MUST conform with the latest
edition of the National Electrical Code,
ANSI/NFPA No. 70, and such local
regulations as might apply. It is the
customer’s responsibility to have the
wiring, fuses and circuit breakers
installed by a qualified electrician to make
sure adequate electrical power is
available to the washer.
W518
1
2
3
4
5
L1
Ground
Neutral Side
Round Grounding Prong
Neutral
Figure 16
WARNING
To reduce the risk of an electric shock or
fire, DO NOT use an extension cord or an
adapter to connect the washer to the
electric power source.
W082
When plugging in the washer:
 DO NOT overload circuits.
 DO NOT use an extension cord.
 DO NOT use an adapter.
 DO NOT operate other appliances on the same
circuit. Use separately fused 15 Amp circuits.
14
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
802734ENR7
Installation
Grounding Instructions
Step 9: Check Installation
The washer must be grounded. In the event of
malfunction or breakdown, grounding will reduce the
risk of electric shock by providing a path of least
resistance for electric current.
Refer to Installer Checklist on the back cover of this
manual and make sure that washer is installed
correctly.
The washer is equipped with a cord having an
equipment-grounding conductor and a three-prong
grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and
grounded in accordance with all local codes and
ordinances.
Run washer with a test load to make sure it is
operating properly and properly leveled.
a. Put about six pounds of laundry (four bath
towels and three jeans) into washer.
b. Close door.
c. Rapid advance to spin portion of cycle.
d. When washer spins at high speed, verify that
it is stable.
WARNING
Improper connection of the equipmentgrounding conductor can result in a risk
of electric shock. Check with a qualified
electrician or service person if you are in
doubt as to whether the washer is
properly grounded.
e. If it is not, after cycle is complete, refer to
Step 2 and readjust leveling legs.
W327
DO NOT modify the plug provided with the washer –
if it will not fit the outlet, have a proper outlet installed
by a qualified electrician.
NOTE: Have a qualified electrician check the
polarity of the wall receptacle. If a voltage reading
is measured other than that in Figure 16, the
qualified electrician should correct the problem.
802734ENR7
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
15
Installation
Vending
Meter Case
The factory mounted coin meter case does not include
the service door lock, coin slide, coin drawer, coin
drawer lock or keys. These parts must be ordered (at
extra cost) according to the purchaser’s requirements
direct from the manufacturer of your choice.
2. If installing a Greenwald coin slide, position
extension lever (to be installed on extension
bracket) with arm that has one star facing down.
Refer to Figure 17.
Greenwald
Coin Slide
NOTE: On models with standard capacity meter
case and high capacity meter case models starting
with Serial Nos. beginning 1010, you have the
option of using a screw type lock or a 1/4 turn lock
on the meter case service door. If you choose to use
a screw lock, then the special bracket (located
inside the meter case) must be used. DO NOT use
the special bracket if a 1/4 turn lock is used. High
capacity meter case models with Serial Nos.
beginning 0910 through 1010 use 1/4 turn lock only.
Coin Drawer Security (Models with standard
capacity meter case and high capacity meter case
models starting with Serial Nos. beginning 1010
only) – For additional security, drill out the two pilot
holes on each side of the front of the meter case to 1/4
or 5/16 inch (6.4 or 7.9 mm) holes and install a bicycle
lock through these holes.
NOTE: An 8 in. (20.32 cm) coin drawer is required
for coin operated electronic control models with
standard capacity meter case and high capacity
meter case models starting with Serial Nos.
beginning 1010. High capacity meter case models
with Serial Nos. beginning 0910 through 1010
require a 7.21 in. (18.31 cm) coin drawer.
Slide Extension Assembly – Models
through Serial No. 1211
Monarch or
ESD Coin Slide
One Star
Two Stars
TLW2088N
Figure 17
3. If installing a Monarch or ESD coin slide,
position lever with arm that has two stars facing
down. Refer to Figure 17.
4. Install extension lever with rounded corner
facing away from extension bracket using bolt,
one or two flat washers (shims) (use number of
washers included in kit) and nut. Refer to Figure
18. Make sure washers are flat against bracket.
Spring
One or Two
Flat Washers (Shims)
Bolt
Rounded Corner
Nut
Loops
(Coin Slide Models with standard capacity meter
case and high capacity meter case models starting
with Serial Nos. beginning 1010 only)
NOTE: High capacity meter case models with
Serial Nos. beginning 0910 through 1010 require a
coin slide with a switch installed on it.
1. Remove slide extension parts from parts
accessories bag included in unit.
Extension Bracket
Extension Lever
TLW2089N
Star(s) Facing Down
TLW2089N
Figure 18
5. Torque nut between 2 and 2.26 Nm (18 and 20
inch-pounds), or tighten nut firmly.
6. Install extension spring in bracket hole and hole
in upper arm of lever. Refer to Figure 18.
7. Bend loops closed after installation.
8. Check to make sure the lever swings freely.
16
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
802734ENR7
Installation
Installing Extension Onto Coin Slide:
Option 1
1. Install slide extension onto top of coin slide using
two remaining screws and lockwashers. Refer to
Figure 19.
Attaching
Screws
6. Check to make sure coin slide is operating
properly by inserting coins and starting a cycle.
The IN USE light will turn on, or flash if it is
already on, to indicate proper operation.
Installing Extension Onto Coin Slide:
Option 2
1. Install coin slide according to manufacturer’s
instructions.
2. Insert coins into coin slide and slowly push slide
in. Stop before coins fall into coin box. This will
allow installing extension through meter case
service door opening.
Lockwashers
Coin Slide
Slide
Extension
3. Install slide extension onto top of coin slide using
two screws and lockwashers. Refer to Figure 19.
NOTE: Make sure extension lever is above switch
activation lever.
TLW1564K
Figure 19
2. Insert coins and partially extend coin slide.
3. Insert coin slide on its side through meter case
opening. Then rotate 90 degrees to its proper
orientation.
4. Return coin slide and hook slide pins onto meter
case.
5. Continue coin slide installation according to
manufacturer’s instructions.
4. Check to make sure coin slide is operating
properly by inserting coins and starting a cycle.
The IN USE light will turn on, or flash if it is
already on, to indicate proper operation.
Slide Extension Assembly – Models
Starting Serial No. 1211
1. Remove slide extension parts from parts
accessories bag included in unit.
2. Install extension lever with arm that has one star
facing down. Refer to Figure 21.
NOTE: During coin slide installation, make sure
activation lever is up and off the switch. Refer to
Figure 20.
1
One Star
TLW2088N
Figure 21
TLW2090N
TLW2090N
1
Lever Off Switch
Figure 20
802734ENR7
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
17
Installation
NOTE: If more switch down-force is required,
install lever with arm that has two stars facing
down to provide additional switch travel.
3. Install extension lever with rounded corner
facing away from extension bracket using bolt,
washer and nut. Refer to Figure 22.
Extension Bracket and
Lever Assembly
Coin Slide Bracket Letter "A"
Spring
Installed
4. Install spring to extension bracket with hook
facing down. Install other end of spring to
extension lever with hook facing left while
standing in front of unit. Refer to Figure 22.
Spring
Washer
Bolt
Rounded
Corner
TLW2163N
Figure 23
Extension
Bracket
Nut
6. Install coin slide extension assembly onto top of
coin slide using two remaining screws and
lockwashers. Refer to Figure 24.
TLW1610K
Extension
Lever
TLW1610K
Coin Slide Extension
Assembly
Spring Installed
Figure 22
5. Install extension bracket and lever assembly onto
coin slide bracket using two screws and locknuts.
Refer to Figure 23.
IMPORTANT: Install coin slide bracket with side
marked "A" facing up and toward extension
bracket and lever assembly. Refer to Figure 23.
TLW2164N
Figure 24
18
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
802734ENR7
Installation
7. Before installing coin slide and extension, make
sure ground wire is tucked under control shield to
provide clearance for coin slide. Refer to
Figure 25.
Ground Wire Placement
Models Prepped for Card Reader
The machine is shipped from the factory with the
Electronic Control Diagnostic Harness Assembly
unplugged. To avoid unauthorized manual
programming or vending, perform the following steps.
1. Open control panel. Refer to Figure 26.
2. Locate diagnostic harness on electronic control.
3. Plug connectors for “white/black” wire and “red/
blue” wire together.
1
TLW2157N
Figure 25
Installing Extension Onto Coin Slide:
Option 1
1. Insert coins and partially extend coin slide.
2. Insert coin slide on its side through meter case
opening. Then rotate 90 degrees to its proper
orientation.
3. Return coin slide and hook slide pins onto meter
case.
FLW6R
1
Control Panel
Figure 26
4. Continue coin slide installation according to
manufacturer’s instructions.
5. Check to make sure coin slide is operating
properly by inserting coins and starting a cycle.
The IN USE light will turn on, or flash if it is
already on, to indicate proper operation.
Installing Extension Onto Coin Slide:
Option 2
1. Install coin slide according to manufacturer’s
instructions.
2. Insert coins into coin slide and slowly push slide
in. Stop before coins fall into coin box. This will
allow installing extension through meter case
service door opening.
3. Install slide extension onto top of coin slide using
two screws. Refer to Figure 24.
4. Check to make sure coin slide is operating
properly by inserting coins and starting a cycle.
The IN USE light will turn on, or flash if it is
already on, to indicate proper operation.
802734ENR7
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
19
Operation
Operation Instructions for Coin
Slide Operated Washers
IMPORTANT: Prior to first wash, use an allpurpose cleaner, or a detergent and water solution,
and a damp cloth to remove shipping dust from
inside of washtub.
Step 2: Close Loading Door
Close the loading door tightly. The washer will not
operate with the loading door open.
O
IMPORTANT: Remove all sharp objects from
laundry to avoid tears and rips to items during
normal machine operation.
Step 1: Load Laundry
Load items loosely into wash drum.
NOTE: Small items such as baby socks may get
caught around the door. Place these articles inside a
mesh garment bag.
FLW2128N
Figure 28
FLW2127N
Figure 27
When washing bulky items such as blankets and
comforters, use the DELICATE cycle. The cycle
includes agitation and final spin speeds that maintain
the load’s balance and minimize wear to the articles.
20
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
802734ENR7
Operation
Step 3: Add Laundry Supplies
Step 4: Set Fabric Selector
Open dispenser drawer. Measure and add low sudsing,
high efficiency (HE) detergent (1), bleach (2) and
fabric softener (3) to the dispenser drawer (refer to
Figure 29). Close dispenser drawer.
Set regular loads at NORMAL or PERM PRESS. Set
delicate loads at DELICATE.
IMPORTANT: If using non-HE detergent, avoid
oversudsing by using 1/2 of the detergent
manufacturer's recommended amount.
CAUTION
H171I
Dispenser drawer requires a special tool
for removal. Contact a service person if
removal is necessary.
W236
Figure 30
Step 5: Set WASH/RINSE Temperatures
Set at HOT (COLD rinse), WARM (COLD rinse) or
COLD (COLD rinse).
NOTE: Always follow manufacturer’s care labels.
3
2
1
H170I
Figure 31
Step 6: Insert Money
FLW2129N
FLW2129N
1
2
3
Place coin(s) in slide and carefully push in as far as
possible and then pull slide out as far as possible. After
IN USE light comes on (indicating start of cycle),
press the PUSH-TO-START button.
Detergent
Bleach
Fabric Softener
1
Figure 29
W297I
1
W297I
Service Door
Figure 32
802734ENR7
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
21
Operation
Indicator Lights
Rapid Advance
IN USE
The Rapid Advance feature allows the owner to
quickly advance through an active cycle to a specific
cycle step.
This light will remain on while washer is in use.
DOOR LOCKED
This light will come on after the PUSH-TO-START
button has been pressed and the washer door has
locked. It will remain on until the wash cycle has
ended.
FINAL SPIN AND TUMBLE
This light will come on at the start of the final spin and
remain on until the wash cycle has ended.
CLOSE DOOR
This light will come on if door is not closed tightly.
Firmly push door until light goes out.
IMPORTANT: If washer fails to operate properly
after installation, make sure electrical service and
water supply faucets are turned on. Are all the
controls properly set? Have a qualified service
person refer to the wiring diagram (located inside
of cabinet) and check for broken, loose or incorrect
wiring.
NOTE: Once a cycle has started, the door can only
be opened by first unplugging the power cord and
waiting one minute.
NOTE: If service door remains open, rapid
advance cycles can be used for a free vend.
Press the PUSH-TO-START button to start the cycle.
Press PUSH-TO-START button again to advance
through each cycle step. Refer to Table 1 for cycle
steps.
Cycle Steps
Wash Fill/Agitate cycle step
Wash Distribute cycle step
Wash Pulse Spin cycle step
Rinse Fill/Agitate cycle step
Rinse Distribute cycle step
Rinse Pulse Spin cycle step
Extra Rinse Fill/Agitate cycle step (If extra rinse is
enabled)
Extra Rinse Distribute cycle step (If extra rinse is enabled)
Extra Rinse Pulse Spin cycle step (If extra rinse is enabled)
WARNING
Final Fill/Agitate cycle step
To reduce the risk of bodily injury, do not
remove laundry from washer until all
lights are out, and all moving parts have
stopped.
W092
The washer will stop (pause) shortly before the first
spin and final spin.
22
To enter Rapid Advance, open the service door long
enough for the IN USE light to turn on and close the
door. Refer to Figure 32.
Final Distribute cycle step
Final Pulse Spin cycle step
Final High Spin cycle step (Final Spin light on)
Breakaway cycle step (Final Spin light on)
End of cycle (door will remain locked for about 1 minute)
Table 1
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
802734ENR7
Operation
Operation Instructions for
MDC Washers
Step 2: Close Loading Door
IMPORTANT: Prior to first wash, use an allpurpose cleaner, or a detergent and water solution,
and a damp cloth to remove shipping dust from
inside of washtub.
Close loading door tightly. The washer will not
operate with the loading door open.
IMPORTANT: Remove all sharp objects from
laundry to avoid tears and rips to items during
normal machine operation.
Step 1: Load Laundry
Load items loosely into wash drum.
NOTE: Small items such as baby socks may get
caught around the door. Place these articles inside a
mesh garment bag.
FLW2132N
FLW2132N
Figure 34
FLW2131N
Figure 33
When washing bulky items such as blankets and
comforters, use the DELICATES COLD cycle. The
cycle includes agitation and final spin speeds that
maintain the load’s balance and minimize wear to the
articles.
802734ENR7
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
23
Operation
Step 3: Add Laundry Supplies
Open dispenser drawer. Measure and add low sudsing,
high efficiency (HE) detergent (1), bleach (2) and
fabric softener (3) to the dispenser drawer (refer to
Figure 35). Close dispenser drawer.
IMPORTANT: If using non-HE detergent, avoid
oversudsing by using 1/2 of the detergent
manufacturer's recommended amount.
Step 4: Set Fabric Selector and Wash
Temperature
Push touchpad for NORMAL/HOT, NORMAL/
WARM, PERM PRESS/WARM or DELICATES/
COLD cycle. Light indicates selection.
NOTE: Changes can be made to Fabric Selector
setting up until the first fill is complete.
3
2
1
FLW1920N
FLW1920N
Figure 36
FLW2130N
1
2
3
Detergent
Bleach
Fabric Softener
Figure 35
CAUTION
Dispenser drawer requires a special tool
for removal. Contact a service person if
removal is necessary.
W236
24
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
802734ENR7
Operation
Step 5: Insert Coin(s) or Card
Step 6: Start Washer
To Insert Money
After vend price has been satisfied, push the START
pad. DOOR MUST BE CLOSED TO START
WASHER.
Insert coin(s) in coin slot. Check pricing as seen on
digital display.
FLW1923N
W387I
Figure 37
FLW1923N
Figure 39
To Insert Card
Insert card into opening.
DRY1927N
Figure 38
802734ENR7
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
25
Operation
Indicator Lights
WASH
WASH is lit at the beginning of a wash cycle and will
remain lit until the wash cycle is complete.
RINSE
RINSE is lit at the beginning of all RINSE cycles and
will remain lit until the rinse cycle is complete.
SPIN
IMPORTANT: If washer fails to operate properly
after installation, make sure electrical service and
water supply faucets are turned on. Are all the
controls properly set? Have a qualified service
person refer to the wiring diagram (located inside
of washer control hood) and check for broken,
loose or incorrect wiring.
NOTE: Once a cycle has started, the door can only
be opened by first unplugging the power cord and
waiting one minute.
SPIN is lit for all spin cycles.
WARNING
DOOR LOCKED
DOOR LOCKED is lit whenever the door is locked.
The door cannot be opened when this light is on.
START
START flashes one second on and one second off when
the full vend price has been satisfied.
26
To reduce the risk of bodily injury, do not
remove laundry from washer until all
lights are out, and all moving parts have
stopped.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
W092
802734ENR7
Operation
Operation Instructions for
NetMaster Washers
Step 3: Add Laundry Supplies
IMPORTANT: Prior to first wash, use an allpurpose cleaner, or a detergent and water solution,
and a damp cloth to remove shipping dust from
inside of washtub.
IMPORTANT: Remove all sharp objects from
laundry to avoid tears and rips to items during
normal machine operation.
Open dispenser drawer. Measure and add low sudsing,
high efficiency (HE) detergent (1), bleach (2) and
fabric softener (3) to the dispenser drawer (refer to
Figure 42). Close dispenser drawer.
IMPORTANT: If using non-HE detergent, avoid
oversudsing by using 1/2 of the detergent
manufacturer's recommended amount.
Step 1: Load Laundry
3
Load items loosely into wash drum.
2
NOTE: Small items such as baby socks may get
caught around the door. Place these articles inside a
mesh garment bag.
1
FLW2130N
1
2
3
Detergent
Bleach
Fabric Softener
FLW2131N
Figure 42
Figure 40
When washing bulky items such as blankets and
comforters, use the DELICATES cycle. The cycle
includes agitation and final spin speeds that maintain
the load’s balance and minimize wear to the articles.
Step 2: Close Loading Door
CAUTION
Dispenser drawer requires a special tool
for removal. Contact a service person if
removal is necessary.
W236
Close loading door tightly. The washer will not
operate with the loading door open.
FLW2132N
Figure 41
802734ENR7
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
27
Operation
Step 4: Set Fabric Selector
Step 6: Insert Coin(s) or Card
Push touchpad for NORMAL, PERM PRESS or
DELICATES cycle. Light indicates selection.
To Insert Money
NOTE: Changes can be made to Fabric Selector
setting up until the first fill is complete.
NORMAL
PERM
PRESS
DELICATES
HOT
WARM
COLD
Insert coin(s) in coin slot. Check pricing as seen on
digital display.
START
W387I
H205I
Figure 45
H205I
To Insert Card
Figure 43
Step 5: Set Wash Temperature
Push touchpad for HOT, WARM or COLD. Light
indicates selection.
Insert card into opening. Do not remove the card until
REMOVE CARD LED is lit.
NOTE: Always follow manufacturer’s care labels.
NORMAL
PERM
PRESS
DELICATES
HOT
WARM
COLD
START
M343I
Figure 46
H206I
H206I
Figure 44
28
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
802734ENR7
Operation
Step 7: Start Washer
INSERT COIN/CARD
After vend price has been satisfied, push the START
pad. DOOR MUST BE CLOSED TO START
WASHER.
INSERT COIN/CARD is lit to prompt the user to insert
coins or card to satisfy the vend price. When INSERT
COIN/CARD is lit, the digits and decimal point show
the vend price remaining to be satisfied.
REMOVE CARD (Card Models Only)
NORMAL
HOT
PERM
PRESS
WARM
DELICATES
COLD
REMOVE CARD flashes after the START pad has
been pressed and the vend has been deducted from the
card.
START
IMPORTANT: If washer fails to operate properly
after installation, make sure electrical service and
water supply faucets are turned on. Are all the
controls properly set? Have a qualified service
person refer to the wiring diagram (located inside
of washer control hood) and check for broken,
loose or incorrect wiring.
H207I
H207I
Figure 47
Indicator Lights
WASH
WASH is lit at the beginning of a wash cycle and will
remain lit until the wash cycle is complete.
RINSE
RINSE is lit at the beginning of the RINSE or EXTRA
RINSE cycle and will remain lit until the rinse cycle is
complete.
NOTE: Once a cycle has started, the door can only
be opened by first unplugging the power cord and
waiting one minute.
WARNING
To reduce the risk of bodily injury, do not
remove laundry from washer until all
lights are out, and all moving parts have
stopped.
W092
SPIN
SPIN is lit for all spin cycles.
DOOR LOCKED
DOOR LOCKED is lit whenever the door is locked.
The door cannot be opened when this light is on.
802734ENR7
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
29
Maintenance
User-Maintenance Instructions
Replacing Hoses
Lubrication
Hoses and other natural rubber parts deteriorate after
extended use. Hoses may develop cracks, blisters or
material wear from the temperature and constant high
pressure they are subjected to.
All moving parts are sealed in a permanent supply of
lubricant or are equipped with oilless bearings.
Additional lubrication will not be necessary.
Do not lubricate the door hinge. If the hinge makes
noise, replace the hinge.
Cold Weather Care
All hoses should be checked on a monthly basis for
any visible signs of deterioration. Any hose showing
the signs of deterioration listed above should be
replaced immediately. All hoses should be replaced
every five years.
If the washer is delivered on a cold day (below
freezing), or is stored in an unheated room or area
during the cold months, do not attempt to operate it
until the washer has had a chance to warm up.
Filter Screens
Care of Your Washer
If the washer is filling with water slower than normal,
check the filter screens. Clean or replace them if
necessary.
Use only a damp or sudsy cloth for cleaning the
control panel. Some cleaning product sprays may
harm the finish on the control panel or damage the
interior of the hood. DO NOT use products that
contain alcohol on the control panel.
Wipe the washer cabinet as needed. If detergent,
bleach or other washing products are spilled on the
cabinet, wipe immediately. Some products will cause
permanent damage if spilled on the cabinet.
Do not use scouring pads or abrasive cleansers.
The wash drum will need no particular care although it
may need rinsing or wiping after an unusual load has
been washed.
Check the filter screens in the fill hoses for debris or
damage annually. Clean or replace them if necessary.
Order filter screen Part No. F270300 from the nearest
authorized parts distributor.
Vacations and Extended Non-Use
IMPORTANT: To avoid possible property damage
due to flooding, turn off the water supply to the
washer whenever there will be an extended period
of non-use.
Leave the loading door open during extended periods
of non-use to allow the wash drum to dry out and
avoid a musty smell.
The outside of the door window can be cleaned with
household window cleaner.
Running an occasional rinse cycle with bleach will
help to avoid a musty smell in the wash drum.
Cleaning Glass Sealing Area
In order to assure that the door properly seals against
water leaks, the following surfaces should be wiped
off periodically:
 The outside perimeter of the door glass where the
seal contacts the glass
 The front surface of the door seal lip
Usually a mild soap solution will work. If there is an
extreme build-up of minerals from a hard water
supply, the surfaces may need to be cleaned with a
lime removal chemical.
30
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
802734ENR7
Maintenance
Reinstallation of Shipping Materials
Cleaning Foreign Object Trap
To prevent damage while moving the washer, the
shipping materials MUST be reinstalled.
The washer’s pump has a trap that may collect foreign
objects. The trap may need to be cleaned if water is
draining slower than usual. To clean:
 Disconnect washer from electrical supply.
 While supporting the front access panel, remove
two screws from the bottom edge of the panel.
 Gently lower the panel to remove it from the
washer.
 Place the shock sleeves on all four shock
absorbers. Refer to Figure 48.
 Insert hooked end of shipping brace into the open
slot of the motor mount. Refer to Figure 48.
 Attach the brace with the five bolts and washers.
Refer to Figure 48.
 Reinstall front access panel.
 Disconnect washer from electrical supply.
 While supporting the front access panel, remove
two screws from the bottom edge of the panel.
 Gently lower the panel to remove it from the
washer.
NOTE: The pump may have some water in it. Use a
rag or a container to catch water. If the wash drum
is full of water, use a wet/dry shop vacuum to catch
the water.
 With rag or vacuum ready, unscrew the cap on
the left side of the pump and remove trap.
 Clean the debris from the trap.
 Reinstall the trap and access panel.
 Reconnect washer to electrical supply.
1
2
3
4
FLW2124N
FLW2124N
1
2
3
4
Shock Sleeves
Motor Mount
Hooked End of Shipping Brace
Bolts and Lockwashers
Figure 48
Refer to Installation section, step 6 for proper
procedures whenever the washer is moved.
802734ENR7
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
31
Troubleshooting
Try these troubleshooting tips before making a service call. They may save time and money.
Washer Symptom
Possible Cause/Solution
Won’t Fill








Make sure power cord is plugged all the way into the electrical outlet.
Make sure hot and cold water faucets are turned on.
Make sure that the fill hoses are not kinked or twisted.
Press PUSH-TO-START button or START keypad.
Make sure that the controls are properly set.
Make sure that the loading door is closed tightly.
Check the laundry room fuse or circuit breaker.
Clean the screens in the water mixing valve and the filter screens located at the faucet end
of the fill hoses.
Won’t Start







Make sure loading door is closed tightly.
Press PUSH-TO-START button or START keypad.
Make sure power cord is plugged all the way into the electrical outlet.
Check the laundry room fuse or circuit breaker.
Insert coin(s) or card.
Activate time accumulator. Push the coin slide all the way in (coin slide models only).
Make sure door latch is properly adjusted relative to door lock.
Won’t Spin/Tumble







Make sure loading door is closed tightly.
Press PUSH-TO-START button or START keypad.
Make sure power cord is plugged all the way into the electrical outlet.
Make sure controls are properly set.
Check the laundry room fuse or circuit breaker.
Broken drive belt. Call the service person.
Foreign object trap in pump may be clogged. Clean the trap. Refer to
Maintenance section.
Stops/Pauses During
Cycle



Pauses are part of the washer’s normal operation.
Wash load may be unbalanced. Washer will stop and then restart spin automatically.
Check the laundry room fuse or circuit breaker.
Won’t Drain




Make sure drain hose is not kinked or twisted.
Make sure drain hose is not clogged.
Make sure drain receptacle is not clogged.
Refer to the Installation section to make sure that the drain hose has been properly
installed.
Foreign object trap in pump may be clogged. Clean the trap. Refer to Maintenance
section.

Water Leaks







Check that fill hoses are properly installed on the faucets and the washer’s water mixing
valve.
Check the condition of the fill hoses. Replace fill hoses every five years.
Check the condition of the rubber door gasket for tears or holes.
Make sure drain receptacle is not clogged.
Check building plumbing.
Laundry load may be oversudsing or overloaded. Make sure you are using low-sudsing,
high efficiency (HE) detergent and proper load sizes.
Make sure outside perimeter of the door glass where seal contacts glass is clean.
(continued)
32
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
802734ENR7
Troubleshooting
(continued)
Washer Symptom
Too Many Soap Suds
Possible Cause/Solution



Vibrates/Moves
Slightly



Laundry load may be oversudsing. Make sure you are using low sudsing, high efficiency
(HE) detergent.
Make sure you are using the amount of detergent recommended on the detergent’s label.
If using non-HE detergent, use only 1/2 of the detergent manufacturer's recommended
amount.
Laundry load may be overloaded. Make sure you are using proper load sizes.
Make sure washer is level. Uneven leveling can cause vibration.
Make sure washer is installed on a solid, sturdy and level floor. The washer should not be
installed on carpeting, soft tile, a platform or other weakly supported structures.
Make sure rubber feet are installed on all four leveling legs. Refer to Installation section,
Step 5.
Is Noisy


Make sure washer is level. Uneven leveling can cause vibration.
Some sounds may be a part of normal operation for a frontload washer.
Load is too Wet

Wash load may be unbalanced. The washer may have limited the spin speed to prevent
damage to the machine. Redistribute the load.
Load is too small. Add items to make full load.

Wrong Water
Temperature



802734ENR7
Make sure that the controls are properly set.
Check fill hoses. Make sure hot faucet hose is connected to hot mixing valve (indicated
with “H” on the valve bracket) and cold faucet is connected to cold mixing valve
(indicated with “C” on the valve bracket).
Make sure laundry room water heater is adjusted properly.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
33
Contact Information
If service is required, contact the nearest Factory
Authorized Service Center.
If you are unable to locate an authorized service center
or are unsatisfied with the service performed on your
unit, contact:
Alliance Laundry Systems
Shepard Street
P.O. Box 990
Ripon, WI 54971-0990
U.S.A.
www.alliancelaundry.com
Phone: +1 (920) 748-3121
When calling or writing about your unit, PLEASE
GIVE THE MODEL AND SERIAL NUMBERS. The
model and serial numbers are located on the
nameplate. The nameplate will be in the location
shown in Figure 49.
Date Purchased ____________________________
Model Number ____________________________
Serial Number ____________________________
Please include a copy of your bill of sale and any
service receipts you have.
WARNING
To reduce the risk of serious injury or death,
DO NOT repair or replace any part of the unit
or attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that you understand and have
the skills to carry out.
W329
If replacement parts are required, contact the source
from where you purchased your washer or call (920)
748-3950 for the name and address of the nearest
authorized parts distributor.
1
FLW2123N
FLW2123N
1
Nameplate
Figure 49
34
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
802734ENR7
Installer Checklist
Fast Track for Installing the Washer
(Refer to the manual for more detailed information)
1
5
• Position Washer
Near Installation
Area.
CHECK
(Gravity Drain Models Only)
•
Connect Drain
Outlet to Drain
System.
CHECK
H135IE0A
FLW1980N
FLW1980N
H135IE0A
2
6
• Position and Level
the Washer.
• Remove the Shock
Sleeves and Shipping
Brace.
FLW2125N
FLW2125N
CHECK
CHECK
3
• Connect Fill Hoses.
7
COLD
HOT
FLW2124N
FLW2124N
• Wipe Out Inside of
Wash Drum.
TLW1976N
TLW1976N
CHECK
4
CHECK
(Non-Gravity Drain Models Only)
8
• Connect Drain Hose
to Drain Receptacle.
• Plug In the
Washer
D254IE0A
FLW1979N
FLW1979N
CHECK
FLW2126N
FLW2126N
D254IE0A
CHECK
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT