Everdure RBES63 Operating instructions

INSTALLATION, OPERATION
& MAINTENANCE INSTRUCTIONS
FOR EVERDURE RANGE HOOD
Models Included:
RBES63
RBES91
RBES92 IMBERLEY
DESIGNED TO PERFECTION
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
FOR EVERDURE RANGE HOOD RBES63, RBES91, RBES92
CONTENTS
SECTION
PAGE NO.
Important Safety Instructions………………
Appliance Details …………………………
General Information ……………………..
What Is Supplied ………….………………
What May Be Needed For Installation …
Installation Instructions ……………………
Operating Instructions ……………………
Cleaning ……………………………………
Troubleshooting ……………………………
3
4
4
4
4
4-6
7-8
9
10
It is important that you retain these instructions, proof of purchase as well as
other important documents about this product for future reference.
2
DESIGNED TO PERFECTION
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT:
Read the assembly instruction section and safety precautions of this booklet
carefully before removing the contents of this carton.
1.
In certain circumstances electrical appliances may be a danger hazard.
2.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience or knowledge, unless they have been given supervision or
instruction concerning the use of the appliance by a person responsible for their safety. Children should
be supervised to insure that they do not play with the appliance.
3.
Do not check the status of the filters while the cooker hood is operating.
4.
Do not touch the light bulbs after appliance use.
5.
Do not disconnect the appliance with wet hands and do not disconnect the power cord with extreme
force.
6.
7.
8.
9.
10.
Do not flambé underneath range hood.
Avoid free flame, as it may cause damage to the filters and be a fire hazard.
If frying food, ensure to check regularly to avoid the oil overheating and becoming a fire hazard.
Unplug the appliance before carrying out maintenance or replacing lamps.
If the power cord is damaged, it must be replaced the manufacturer, an authorized service centre or
similarly qualified persons to avoid a hazard.
Indoor use only.
When the appliance is not in use and before cleaning, unplug the appliance from the outlet.
It is recommended to operate the range hood prior to cooking.
It is recommended to leave the range hood in operation for 15 minutes after cooking is terminated in
order to completely eliminate cooking vapours and odours.
Turn off the range hood when not in use.
Don’t use or stop use if the range hood is damaged especially the supply cord and the case.
Don’t immerse the range hood in liquid.
The exhaust air must not be discharge into a flue which is used for exhausting fumes from appliance
burning gas or other fuels (not applicable to appliances that only discharge the air back into the room).
Regulations concerning the discharge of air have to be fulfilled. There shall be adequate ventilation of
the room when the range hood is used at the same time as appliances burning gas of other fuels.
Clean the surface of the cooker hood regularly using cloth moistened with denatured alcohol of non
abrasive liquid detergent.
There is a fire risk if cleaning is not carried out in accordance with the instruction.
The 600mm unit is intended for use above hobs with four elements and the 900mm units are intended
for use above hobs units with five elements.
If the instruction for the minimum distance between the supporting surface of the cooking vessels on the
hob and the lowest part of the range hood are specified by hob instructions, these instructions should be
taken into account.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
DO NOT
OPERATE THIS APPLIANCE BEFORE READING THE
INSTRUCTION BOOKLET
DESIGNED TO PERFECTION
3
APPLIANCE DETAILS
Voltage:
220-240V
Frequency:
50Hz
Lamp Max:
2x20W G4 halogen lamps
Rated Input Power:
230W
GENERAL INFORMATION
Before installing and operating the range hood, carefully read the following important information regarding
installation safety and maintenance. Keep this information booklet accessible for further consultations.
The appliance has been designed to exhaust cooking fumes externally. Before installation, please ensure that
the following have been supplied and that the tools listed below are readily available.
WHAT IS SUPPLIED
Range hood (including one way valve for flue x 1) x 1
Installation kit x 1 – RBES63 & RBES91: Short bolts x 10, long screws x 7, plastic plugs x 7
Installation kit x 1 – RBES92: Short bolts x 8, Medium bolts x 4, long screws x 7, plastic plugs x 7
Mounting brackets x 3
Instruction booklet x 1
WHAT MAY BE NEEDED FOR INSTALLATION
Electric Drill
Tape Measure
Spirit Level
Screwdrivers
Duct Tape
Jig Saw
Ladder
Torch (If natural lighting is minimal)
INSTALLATION INSTRUCTIONS
Please ensure that before installing the range hood, all power is switched off.
Installation must be in accordance to the local electrical authority and codes.
This range hood must be earthed at all times for the operators’ safety.
The G.P.O. for the range hood should be positioned to enable the user to turn the power off, to enable
cleaning and any maintenance required.
The G.P.O. should be installed within 600mm from the rear of the unit.
Ensure that when installing the range hood, that it is protected from any possible damage from tools etc.
Ducting for this unit must be installed in accordance to the local authority.
Ensure that the fixings used for this range hood are suitable.
Check the area where the range hood is to be fitted, to ensure that it is structurally sound.
The Everdure RBES63, RBES91 & RBES92 range hoods are intended to be installed directly onto a wall.
4
DESIGNED TO PERFECTION
INSTALLATION OF THE EVERDURE RBES63 & RBES91 RANGE HOODS DIRECTLY TO A WALL
Ensure that the wall is structurally sound, and is capable of carrying the weight of the range hood.
The range hood can be placed at a minimum of 600mm away from an electric cooktop, or 650mm
minimum from a gas cooktop. The unit is held to a wall via 3 brackets (supplied with the unit):
1. Hook Bracket.
2. Centre Bracket (flat).
3. Top Bracket (U-shaped).
Place the hood main unit (no u-shaped section) against the wall at the correct position and mark off the top
of the unit. Remove the unit and measure up 22mm to get the top level for the hook bracket. Place the hook
bracket (hooks up) under the mark and mark in the 3 screw holes. Remove the bracket and drill three (3)
Ø8mm holes 100mm apart. Insert plastic plugs into the holes and fix the hook bracket onto the wall. Place
the hood main unit onto the hooks. See pic2.
Screw the centre bracket onto the back of the u-shaped section using the supplied short screws (this helps
keep the width at the back even with the front). Place the u-shaped section onto the main unit and fix in
place with 2 short screws.
Add the soot tube to the one way valve, and vent it outside. See pic3.
Calculate the final height of the u-shaped section and pull out the inside u-shaped section to a suitable
height (see pic4) to check. Mark the 2 sides near the top and push the inner section out of the way. Place
the top bracket (slots to the bottom) centred between the 2 marks, mark the 2 screw holes. Remove the
bracket and drill two (2) Ø8mm holes at the marks. Insert plastic plugs into the holes and fix the hook
bracket onto the wall (slightly loose). Note: The top edge of the u-shaped bracket matches the top edge of
the u-shaped section – adjust according to your own needs.
Pull up the inside u-section to allocate the top bracket correctly, and tighten the screws. Pull the u-section
over the bracket completely and fix into place with 2 screws at the sides (see pic5).
For timber framed houses, special care should be taken that all brackets are attached to areas that will
support the weight of the range hood.
DESIGNED TO PERFECTION
5
INSTALLATION OF THE EVERDURE RBES92 RANGE HOOD DIRECTLY TO A WALL
Ensure that the wall is structurally sound, and is capable of carrying the weight of the range hood.
The range hood can be placed at a minimum of 600mm away from an electric cooktop, or 650mm
minimum from a gas cooktop. The unit is held to a wall via 3 brackets (supplied with the unit):
1. Hook Bracket.
2. Centre Bracket (flat).
3. Top Bracket (U-shaped).
Place the hood main unit (no u-shaped section) against the wall at the correct position and mark off the top
of the unit. Remove the unit and measure up 20mm to get the top level for the hook bracket. Place the hook
bracket (hooks up) under the mark and mark in the 3 screw holes. Remove the bracket and drill three (3)
Ø8mm holes 115mm apart. Insert plastic plugs into the holes and fix the hook bracket onto the wall. Place
the hood main unit onto the hooks. See pic1.
Add the soot tube to the one way valve, and vent it outside (See pic2).
Screw the centre bracket onto the back of the u-shaped section using the supplied short screws (this helps
keep the width at the back even with the front). Place the u-shaped section onto the main unit and fix in
place with 2 short screws (see pic3A). Slide the glass into position and fix into place with 4 screws (see
pic3B).
Calculate the final height of the u-shaped section and pull out the inside u-shaped section to a suitable
height (see pic4) to check. Mark the 2 sides near the top and push the inner section out of the way. Place
the top bracket (slots to the bottom) centred between the 2 marks, mark the 2 screw holes. Remove the
bracket and drill two (2) Ø8mm holes at the marks. Insert plastic plugs into the holes and fix the hook
bracket onto the wall (slightly loose). Note: The top edge of the u-shaped bracket matches the top edge of
the u-shaped section – adjust according to your own needs.
Pull up the inside u-section to allocate the top bracket correctly, and tighten the screws. Pull the u-section
over the bracket completely and fix into place with 2 screws at the sides (see pic5).
For timber framed houses, special care should be taken that all brackets are attached to areas that will
support the weight of the range hood.
NOTE: Care should be taken that the range hood is fitted correctly (see diagram below). Incorrect
installation can cause a build up of grease and oils and cause damage to the unit.
NOTE: Remove all protective plastic coatings from the stainless steel surfaces before use.
6
DESIGNED TO PERFECTION
OPERATING INSTRUCTIONS
Note: Before the unit can be operated, it must be ducted.
Connect the plug into the power.
FOR RBES92 ELECTRONICALLY OPERATED RANGEHOODS
The range hood has indication diagrams to allow you to easily select the fan operating speed required.
Push the low button, indicated by a fan with 3 blades, and the motor will run at a low speed. An indicator
light will also illuminate. Push it again and the motor will stop.
Push the medium button, indicated by a fan with 4 blades and the motor will run at a medium speed. An
indicator light will also illuminate. Push it again and the motor will stop.
Push the high button, indicated by a fan with 5 blades and the motor will run at a high speed. An indicator
light will also illuminate. Push it again and the motor will stop.
Push the light button; the indicating light on, and the two lighting lamps will come on. Push it again and the
lamps will turn off.
DESIGNED TO PERFECTION
7
FOR RBES63 & RBES91 PUSH BUTTON OPERATED RANGEHOODS
The range hood has indication diagrams to allow you to easily select the fan operating speed required.
Push the low button, indicated by a fan with 3 blades, and the motor will run at a low speed.
Push the medium button, indicated by a fan with 4 blades and the motor will run at a medium speed.
Push the high button, indicated by a fan with 5 blades and the motor will run at a high speed.
Push stop button, indicated by an (O) and the motor will stop.
Push the light button, indicated by a lit globe and the two lights will come on. Push it again and the light will
turn off.
DESIGNED TO PERFECTION
Light
High
Mid
Low
Stop
8
CLEANING
SAFETY PRECAUTION
Before cleaning your range hood or performing any maintenance, please ensure that the range hood is
turned off at the power point.
Do not use abrasive cleaners to clean the range hood. The use of warm soapy water and a cloth are
recommended.
Ensure that the range hood is cleaned regularly, as a build up of grease and fat may occur otherwise.
The filters on the range hood must be cleaned regularly to maintain efficiency, and prevent grease build up.
It is recommended that this is undertaken every 4 – 6 weeks, depending on frequency of use.
The filters can be cleaned with warm soapy water or a cloth, or they may be washed in a dishwasher. If
washed in a dishwasher, discolouration may occur to the mesh and frame.
Cleaning of the range hood must be performed as described above, otherwise there is a possibility of a fire
hazard due to grease and fat build up.
The filters on the range hood must be cleaned regularly to maintain efficiency, and prevent grease build up.
The filter mesh is made of a high density Stainless Steel. It is recommended that this is undertaken every 4 –
6 weeks, depending on frequency of use.
The filters can be cleaned with warm soapy water or a cloth, or they may be washed in a dishwasher. If
washed in a dishwasher, discolouration may occur to the mesh and frame.
DESIGNED TO PERFECTION
9
TROUBLESHOOTING
Fault
Light on, but
motor does
not work
Possible Cause
Solution
The impellor leaf blocked
Get rid of the blockage
The capacitor damaged
Replace capacitor (By an authorised
person only)
Replace motor (By an authorised
person only)
Replace motor (By an authorised
person only)
Replace lights
The motor bearing damaged or
jammed
A bad smell from the motor
Light damaged
Light does not
work, motor
does not work
Oil leakage
Shaking of the
hood
Power cord loose or disconnected
One way valve and the air
ventilation entrance are not tightly
sealed
Leakage from the connection of Ushaped section and cover
The impellor leaf damaged and
causes shaking
The motor is not fixed tightly
The body is not fixed tightly
Insufficient
suction
The Range
hood inclines
The distance between the range
hood and the gas top is too far
The fixing screw not tight enough
Connect the wires as per the
electric diagram (By an authorised
person only)
Take down the one way valve and
seal with sealant
Take U-shaped section down and
seal.
Replace the leaf (By an authorised
person only)
Lock the motor tightly (By an
authorised person only)
Fix the body tightly
Refit the range hood to the correct
distance
Tighten the hanging screw and
make it horizontal
NOTE: Any electrical repairs to this appliance must conform to your local, state and federal laws. Please
contact the service centre if in any doubt before undertaking any of the above.
10
DESIGNED TO PERFECTION
7
10
DESIGNED TO PERFECTION
11
All Service and Assembly Enquiries:
1300 766 066
A division of Shriro Australia Pty Ltd
23-27 Chaplin Drive Lane Cove NSW 2066
1300 766 066
www.everdurekitchen.com.au
IM Ref: RBES63 27/2009/02FC
FOR INDOOR USE ONLY
DESIGNED TO PERFECTION