DREO DR-HSH013B Portable Electric Space Heater User Manual

Add to My manuals
11 Pages

advertisement

DREO DR-HSH013B Portable Electric Space Heater User Manual | Manualzz
PTC Fan Heater
USER MANUAL
www.dreo.com
DR-HSH013B
Looking for help?
Contact us to get expert support.
[email protected]
(888) 290-1688
Mon - Fri, 9:00 am-5:00 pm PST/PDT
www.dreo.com
,,
Thanks for
Choosing
DREO!
Extend Warranty
to 30 Months
Scan or visit dreo.com/warranty
to extend your warranty for free by registering your product.
If you have any product issues, we always stand ready to help.
[email protected]
www.dreo.com
(888) 290-1688
Your support means the world to us. We
hope you enjoy our product as much as
we did creating it.
Mon - Fri, 9:00 am-5:00 pm PST/PDT
CONTENTS
1
2
KNOWING YOUR
HEATER
USING YOUR
HEATER
1-4
5
6-10
4
5
6
11-12
13-14
15-16
IMPORTANT SAFETY
INSTRUCTIONS
CLEANING AND
MAINTENANCE
TROUBLESHOOTING
3
DREO CUSTOMER
CARE
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical
appliances, basic
precautions should
always be followed to
reduce the risk of fire,
electric shock, and
injury to persons and
hyperthermia, including the following:
GENERAL SAFETY
Warning:
In order to avoid
overheating, do not
cover the heater.
1
Do not use the
fan heater near
near flammables
and combustibles.
1. Read all instructions before using this heater.
2. This heater is hot when in use. To avoid burns, do not let bare skin touch
hot surfaces.
3. Use the handle to move this heater.
4. Extreme caution is necessary when any heater is used by or near children
or invalids and whenever the heater is left operating and unattended.
5. Do not insert or allow foreign objects to enter any ventilation or exhaust
opening as this may cause an electric shock or fire, or damage the heater.
6. The output of this heater may vary and its temperature may become hot
enough to burn exposed skin. Use of this heater is not recommended for
persons with a high sensiticity to heat or an inability to react to avoid burns.
7. Do not attempt to modify or repair the product by yourself. Doing so could
void the warranty and cause damage or personal injury. Only a repair technician may disassemble or repair this product.
8. Make sure that no pieces of polystyrene or other packaging material have
been left between elements of the appliance. It may be necessary to pass
over the appliance with a vacuum cleaner.
9. If the machine is not working as it should, has received a sharp blow, has
and dropped, damaged, left outdoors, or dropped into water, do not use
and contact Customer Support.
10. There may be a trace of smoke or odor when the unit is first operated. This
indicates that a drop of oil fell on the heating coil during the manufacturing
process.It will quickly evaporate and should not re-occur.
1 Dreo PTC FAN HEATER
LOCATION SAFETY
1. Do not use outdoors.
2. Ensure the heater is on a stable, secure surface to eliminate the
potential of tipping it over.
3. Keep combustible materials, such as furniture, pillows, bedding, papers,
clothes, and curtains at least 3 feet (0.9 m) from the front of the heater
and keep them away from the sides and rear.
4. A heater has hot and arcing or sparking parts inside. Do not use it in
areas where gasoline, where gasoline, paint, or flammable liquids are
used or stored.
5. To prevent a possible fire, do not block air intakes or exhaust in any
manner. Do not use on soft surfaces, like a bed, where openings may
become blocked.
6. This heater is not intended for use in bathrooms, laundry areas and
similar indoor locations. Never locate heater where it may fall into a
bathtub or other water container.
ELECTRICITY SAFETY
1. Always unplug heater when not in use.
2. Do not operate any heater with a damaged cord or plug or after the heater
malfunctions, has been dropped or damaged in any manner. Discard
heater, or return to authorized service facility for examination and/or
repair.
3. Do not run cord under carpeting. Do not cover cord with throw rugs,
runners, or similar coverings. Do not route cord under furniture or
appliances. Arrange cord away from traffic area and where it will not be
tripped over.
4. To disconnect heater, turn controls to off, then remove plug from outlet.
5. Always plug heaters directly into a wall outlet/receptacle.
6. Never use with an extension cord or relocatable power tap (outlet/power
strip).
7. If there is a loose fit between the plug and the socket or the plug becomes
very hot, the socket may need to be replaced. Check with a qualified
electrician to replace the socket.
8. It is normal for the plug and cord to feel warm to the touch.
9. A plug or cord which becomes hot to the touch or becomes distorted in
shape may be a result of a result of a worn electrical outlet. Worn outlets
or receptacles should be replaced prior to further use of the heater.
Plugging the heater into a worn outlet / receptacle may result in overheating of the power cord or fire.
10. This appliance has a polarized plug (one prong is wider than the other). To
reduce the risk of electric shock, this plug is intended to fit in a polarized
plug. If the plug does not fit fully in the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician. Do not attempt to rig this safety
feature.
Dreo PTC FAN HEATER 2
11. Hyperthermia can result in death. Symptoms of hyperthermia include
high body temperature, headache, nausea, vomiting, tiredness, dizziness,
fainting, and rapid pulse. If you begin to experience symptoms related
to hyperthermia, turn off the heater and seek medical attention.
12. To avoid excessive room temperatures which can cause hyperthermia:
DO NOT leave product running unattended in a confined space around
infants, or individuals with reduced physical, sensory, or mental capabilities.
13. Use this heater only as described in this manual. Any other use not
recommended by the manufacturer may cause fire, electric shock, or
injury to persons.
14. CAUTION – High temperature, keep electrical cords, drapery, andother
furnishings at least 3 feet (0.9 m) from the front of the heater and away
from the side and rear.
WARNING – Risk of Hyperthermia.
Safety Plug
This unit is iequipped with Dreo's FortPlug™ restorable overheat protection to prevent fire accidents.
When the area around the power plug switch overheats,
the protection will cut off the heating power to prevent
overheating or fire.
When activated, the screen will show PP and power indicator will
start flashing.
Note: The machine will not be operational until power is
restored to normal.
After the plug overheat protection takes effect, please unplug the
heater and make sure that:
- The current is greater than 15A.
- The socket is not loose or has aged.
- The outlet is not shared with other appliances.
- The heater is not plugged through a extension cord.
- The plug is not bent or damaged.
- The power cord is not tied or pressed by other objects.
Check your Quick Start Guide for detailed safety instructions.
After confirming that the above risks are not present, wait for the plug
temperature to cool (at least 5 minutes), then plug it.
If the overheat plug protection is repeatedly triggered, it is
recommended to use another outlet, or contact Dreo customer
service.
WARNING - Risk of Heat Stroke
(Hyperthermia)
Hyperthermia can result in death in infants or others
Use caution to avoid overheating individuals
Read and follow all instructions before use
FOR HOUSEHOLD
USE ONLY
READ AND SAVE
THESE INSTRUCTIONS
Gentle Reminder:
Specifications
Check the appliance regularly
and refer to TROUBLESHOOTING
or contact our customer support
if it shows any of the following
signs:
- Power cord or plug is damaged.
- Loud noise, unusual smell or excessive heat.
Model
DR-HSH013B
Rated Power
1500W
Input
120V~ 60Hz
HOT SURFACE
THE FRONT SURFACE CAN BE VERY HOT
DURING USE.
DO NOT TOUCH WHEN IN USE.
Caution: To prevent electric shock, please match the wide blade of
the plug with the wide slot insert.
3 Dreo PTC FAN HEATER
Dreo PTC FAN HEATER 4
KNOWING YOUR
HEATER
Package Contents
2
3
USING YOUR
HEATER
Control Panel
Power On/Off
Touch to turn the heater on or off.
Note:
- When the heater is plugged into the electric outlet, the
power indicator
will light in red.
- Once turned off, a 30-second countdown will show up
on the display as the fan will continue to run for 30
seconds to blow out the remaining heat.
Mode Settings
Touch to switch between
->
->
.
Power heat with three heating levels:
H1 (900W),H2 (1300W), H3(1500W)
The heater will automatically select its optimal
heating power, depending on the difference
between the set temperature (41-95 ) and
ambient temperature.
Note:
- When the ambient temperature reaches the
set temperature, the heater will turn off
automatically in 30 seconds.
- When the ambient temperature drops below
the set temperature, the heater will operate on
low or high power (900W or 1500W), depending on
the difference between the two temperatures.
Fan only.
Touch
5 Dreo PTC FAN HEATER
to turn on/off oscillation.
Dreo PTC FAN HEATER 6
Auto-Off Timer
· When the heater is on, touch to set a timer (0-12h).
After the timer ends, the heater will turn off
automatically.
· To cancel, set the timer to 0 hour.
Heat Level / Temperature
· In Power Heat mode, touch
or
to adjust the
heating level.
· In ECO mode, touch
or
to adjust the set
temperature.
Note:
In ECO mode, the heater will turn off automatically when
the set temperature has been reached. If your heater turns
off frequently, please raise the set temperature, or switch
to Power Heat mode.
Child Lock
Long press
and
for 3s to activate /
deactivate the Child Lock function, when activated,
the
on the display will light up, and all the buttons
on the space heater will be locked.
Fan Only
Mute/Unmute
Plugged in
Child Lock
Timer
Power Heat with three
heating levels:
H1(900W)
H2(1300W)
H3(1500W)
Mute/Unmute
To turn on/off the button sounds, long press
for 3s.
7 Dreo PTC FAN HEATER
Dreo PTC FAN HEATER 8
More Features
This appliance features auto-brightness.
The display adapts automatically based on the ambient
lighting conditions.
Touch
to activate the control panel and LED display.
Memory Function
Tip-Over Protection
The heater will remember its
last settings (temperatures,
working modes, oscillation status)
once turned on again.
When the heater is tipped over,it will
shut off automatically with the error
code “ P4 ” on the display.
24-Hour Auto Off
Overheat Protection
This feature is not ON by default.
When this feature is ON, the heater
will shut off automatically after
continuously running for 24 hours.
When the heater overheats, it will
shut off automatically with the error
code “ FF ” on the display.
Long press the timer for 3 seconds
to turn this feature ON/OFF when
this heater is on standby. The
display will show "ON" and "OF"
respectively.
9 Dreo PTC FAN HEATER
Dreo PTC FAN HEATER 10
CLEANING AND
MAINTENANCE
4
ATTENTION
Always turn off and unplug before cleaning.
DO NOT unscrew
the unit.
DO NOT use
cleaning agents.
DO NOT use
abrasive scrubbers.
Fire or electrical shock hazard.
DO NOT immerse the main unit in water.
NEVER allow water to get inside the heater.
Outer Surface
Use a soft, dry cloth to gently wipe clean
the outer surface.
Except for cleaning, any servicing
should be performed by an authorized
service representative.
Store in a cool, dry area and keep the
cable out of high-traffic areas to avoid
tripping hazards.
Air Inlet
Use a soft, dry cloth or a cotton-tipped
swab to remove any dust from the air inlet.
11 Dreo PTC FAN HEATER
Dreo PTC FAN HEATER 12
TROUBLESHOOTING
Problem
Malfunction
codes on LED
display
Possible Causes
5
Solution
E2 - Temperature
sensor short circuit
Unplug it from the power
source and contact
Customer Support.
E1 - Temperature
sensor open circuit
Unplug it from the power
source and contact
Customer Support.
FF - Overheat
Protection
Unplug and wait for it
to cool down before
plugging in again.
P4 - Tip-Over
Protection
Place the heater back on
a flat, level and stable
surface.
Power cord is not
properly plugged in.
Connect the plug to
a powered electrical
outlet.
Heater does
not start
Unplug and allow it to
cool.
Overheat protection
has been activated.
No power is passing
through the unit.
Heater does
not start
The heater
suddenly
stops during
heating.
Ensure that your circuit
breaker or fuse is working
properly.
Ensure that your heater is
placed on a flat and even
surface.
The set temperature
is lower than the ambient
temperature.
Ensure that the temperature is
set to be higher than the
ambient temperature.
The temperature
exceeds the threshold
of the thermal cutoff.
Turn off and unplug the unit.
Allow it to cool and plug into
the electrical outlet again.
The heater is tipped
over.
Place it on a flat, level and
stable surface.
In ECO mode, the heater
will turn off automatically
when the set temperature
has been reached.
This is normal. If your heater
turns off frequently, please
raise the set temperature, or
switch to Power Heat mode.
If your problem is not listed or still persists, contact our Customer
Support (see page 16).
Remove any objects on
or near the heater.
13 Dreo PTC FAN HEATER
Dreo PTC FAN HEATER 14
DREO CUSTOMER
CARE
Default 12-Month Warranty
6
This appliance is covered by Dreo warranty for 12 months from the date of
its original purchase.
Extend Your Warranty
Extend your warranty by registering your new appliance on our website
https://dreo.com/warranty.
The warranty will not apply in cases of:
1. Accident, misuse, or repairs performed by unauthorized personnel.
2. Any unit that has been tampered with or used for commercial purposes.
3. Normal wear and tear of wearable parts.
4. Use of force, damage caused by external influences.
5. Damage caused by non-observance of the User Manual, e.g. connection
to an unsuitable mains supply or noncompliance with the instructions.
6. Partially or completely dismantled appliances.
7. Defects caused by or resulting from damages from shipping or from
repairs, service, or alteration to the product or any of its parts that have
been perform ed by a repair person not authorized by Dreo.
We can only provide after-sales service for products that are sold by Dreo
or Dreo authorized retailers and distributors. If you have purchased the
appliance from a different place, please contact your seller for return and
warranty issues.
We’re Here to Help!
(888) 290-1688
[email protected]
Mon - Fri, 9:00 am-5:00 pm PST/PDT
www.dreo.com
Shenzhen Hesung Innovation
Technology Co., LTD
26F, Bldg A7, Creative City, Shenzhen, China
Rev_1.1_EN
15 Dreo PTC FAN HEATER
Dreo PTC FAN HEATER 16

advertisement

Key Features

  • PTC ceramic heating element for a long lifespan and energy-efficient heat generation.
  • Overheat and tip-over protection for added safety.
  • Adjustable thermostat for precise temperature control.
  • Two heat settings for customizing the warmth level.
  • Easy-to-use controls with a simple interface.
  • LED display for clear visibility.
  • Remote control for convenient operation.
  • Lightweight and portable design for easy movement.
  • Stylish appearance that complements any home décor.

Related manuals

Frequently Answers and Questions

Is the heater safe to use around children and pets?
Yes, the heater has multiple safety features, including overheat and tip-over protection, making it safe to use around children and pets.
How many heat settings does the heater have?
The heater has two heat settings, allowing you to choose the desired warmth level.
Can I use the heater in a bathroom?
No, the heater is not intended for use in bathrooms or other areas with high humidity.
How do I clean the heater?
Unplug the heater and allow it to cool completely before cleaning. Use a soft, dry cloth to wipe down the exterior surfaces.

advertisement