DB98_16569A(2)_1
4/6/04 2:57 PM
Page 14
4. Set Up the Model Option
4-1 Setting Option Setup Method
ex) Option No. :
Step 1 : Enter the Option Setup mode.
1st
Take out the batteries of remote control.
2nd
Press the temperature
insert the battery again.
3rd
Make sure the remocon display shown as
button simultaneously and
.
Step 2 : Enter the Option Setup mode and select your option according to the following procedure.
Feature
1
Display
Setting Option SEG1.
Push the
button to set the display panel to
.
Every time you push the button, the display panel reads
...
repeatedly.
2
Setting Option SEG2.
Push the
button to set the display panel to
.
Every time you push the button, the display panel reads
...
repeatedly.
3
3
1,4
Change it into the set display of Option SEG3 and SEG4
with the
2,5
4
button.
Setting Option SEG3.
Push the
button to set the display panel to
.
Every time you push the button, the display panel reads
...
repeatedly.
5
Setting Option SEG4.
Push the
button to set the display panel to
.
Every time you push the button, the display panel reads
...
repeatedly.
12
Samsung Electronics
DB98_16569A(2)_1
4/6/04 2:57 PM
Page 15
Set Up the Model Option
Feature
Display
6
Change it into the set display of Option SEG5 and SEG6
with the
button.
7
Setting Option SEG5.
Push the
button to set the display panel to
.
Every time you push the button, the display panel reads
...
repeatedly.
8
Setting Option SEG6.
Push the
button to set the display panel to
.
Every time you push the button, the display panel reads
...
repeatedly.
6,9
7,10
8,11
9
Change it into the set display of Option SEG7 and SEG8
with the
button.
10
Setting Option SEG7.
Push the
button to set the display panel to
.
Every time you push the button, the display panel reads
...
repeatedly.
11
Setting Option SEG8.
Push the
button to set the display panel to
.
Every time you push the button, the display panel reads
...
repeatedly.
12
Change it into the set display of Option SEG9 and SEG10
with the
12
13
14
button.
13
Setting Option SEG9.
Push the
button to set the display panel to
.
Every time you push the button, the display panel reads
...
repeatedly.
14
Setting Option SEG10.
Push the
button to set the display panel to
.
Every time you push the button, the display panel reads
...
repeatedly.
Samsung Electronics
13
DB98_16569A(2)_1
4/6/04 2:57 PM
Page 16
Set Up the Model Option
Step 3 : Upon completion of the selection, check you made right selections.
Whenever you press the
button, the set Option will be displayed.
Step 4 : Pressing the ON/OFF button (
)
When pressing the operation ON/OFF key with the direction of remote controller for unit, the sound "Ding" is heard and the
OPERATION LED lamp is flickering at the same time, then the input of option is completed. (If the "ding" sound isn't heard,
try again pressing the ON/OFF button.)
Step 5 : Unit operation test-run
First, Remove the battery from the remote controller.
Second, Re-insert the battery into the remote controller.
Third, Press ON/OFF (
) key with the direction of remote controller for set.
• Error Mode
14
1st
If all lamps of indoor unit are flickering, Plug out, plug in power plug again and press ON/OFF key to retry.
2nd
If the unit is not working properly or all lamps are continuously flickering after setting the option code, see if the
correct option code is set up for its model.
Samsung Electronics
DB98_16569A(2)_1
4/6/04 2:57 PM
Page 17
4-2 Table of the option Code
Model
Option Code
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
SEG8
SEG9
SEG10
2
0
0
0
0
7
0
3
4
0
2
0
0
0
0
7
0
2
2
E
AST12WHWE/AST12WHWB
AS12WHWB/AS14WHWB
AS09W8WB
Samsung Electronics
15